Unified MAPEI MSDS 556101
2015-10-30
: Pdf 556101 556101 Forms
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
MAPEI® Material Safety Data Sheet (MSDS) - North America Read complete MSDS prior to using product. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Product Name: Ultrabond ECO™ 575 Product Description: Premium Cove Base Adhesive ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------IN THE EVENT OF A CHEMICAL EMERGENCY INVOLVING A SPILL, LEAK, FIRE, EXPLOSION, EXPOSURE OR ACCIDENT CONTACT THE FOLLOWING NUMBERS: EMERGENCY 24 HOUR NUMBER (USA) CHEMTREC 1-800-424-9300 (Canada) CANUTEC 1-613-996-6666 CONSUMER STATEMENT: CAUTION - EYE IRRITANT. NON-TOXIC. WORK AND HYGIENE PRACTICE: Remove contaminated clothing immediately. Wash hands, after each use and before eating, drinking, or using toiletries. Minimize contact of product on skins. ________________________________________________________________________________________________________________________ I - GENERAL INFORMATION MANUFACTURER: USA and Puerto Rico Canada MAPEI INC. MAPEI CORPORATION II - PHYSICAL CHARACTERISTICS 0 g/L Calculated VOC (See below.) >212°F (>100°C) Boiling Point 1,0 Vapor Pressure (mmHg) 1144 East Newport Center Drive 2900 Francis-Hughes Avenue Deerfield Beach, FL 33442 Laval, QC H7L 3J5 Vapor Density (AIR=1) Specific Gravity (H20=1) Ph: (954) 246-8888 Ph: (450) 662-1212 Melting/Freezing Point (F) N/E Evaporation Rate (Butyl Acetate=1) Solubility in water pH (paste/liquid) Same as water. Soluble 8,0 - 10,0 Appearance and Odor Beige paste. Slight odor of latex. MSDS PREPARED BY: Regulatory Affairs Department - MAPEI North America REVISION DATE (YYYY/MM/DD): 2005/07/15 For most current MSDS, download document from: www.mapei.com 1,10 - 1,20 1,00 - 1,30 (VOC per CA South Coast Air Quality Management District, Rule 1168) ________________________________________________________________________________________________________________________ III - HAZARD ASSESSMENT Hazardous Components (specific chemical identity; common names): OSHA (PEL) ACGIH (TLVTWA) Other Limits Recommended % Percent (Optional) THIS PRODUCT CONTAINS NO HAZARDOUS INGREDIENTS AS DEFINED BY US OSHA HAZARD COMMUNICATION STANDARD - 29 CFR 1910.1200 OR SECTION 13 OF THE CANADIAN HAZARDOUS PRODUCTS ACT. For California (Proposition 65): This product contains no chemicals reportable under Proposition 65. All ingredients are listed within or exempted from US TSCA and Canadian DSL. (USA) - HMIS (Hazardous Materials Identification System) Rating: Health - 1 Fire - 0 Reactivity - 0 Protection - B "*" = chronic effect (Canada) - WHMIS (Workplace Hazardous Materials Information System) Classifications: Not regulated under WHMIS. ________________________________________________________________________________________________________________________ IV - TRANSPORTATION By GROUND - USA and Puerto Rico (DOT): Not Regulated By SEA (IMDG): Not Regulated By GROUND - Canada (TDG): Not Regulated By AIR (IATA): Not Regulated ________________________________________________________________________________________________________________________ V - FIRE AND EXPLOSION HAZARD DATA Lower Explosive Limit (%) - N/E Upper Explosive Limit (%) Flash Point: >212°F (>100°C) Unusual Fire and Explosion Hazards - Some decomposition products may be harmful. N/E Extinguishing Media: Will not burn except under extreme temperatures. Water spray, carbon dioxide, dry chemical or foam. Special Fire Fighting Procedures: Wear standard fire fighting gear with self-contained breathing apparatus. ________________________________________________________________________________________________________________________ VI - REACTIVITY DATA Stability: Stable Conditions to Avoid: None known. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------English Version on pages 2 and 3. Page 2 of 7 Ultrabond ECO™ 575 Version Française à la pages 4 et 5. La versión en Español en las páginas 6 y 7. MSDS Page 2 de 7 Páginas 2 de 7 Incompatibility (Materials to Avoid): Strong oxidizing agents, strong acids, and strong bases. Hazard Decomposition of By-products: Carbon monoxide, carbon dioxide, oxides of nitrogen, and other unidentified organic compounds. Polymerization: Will Not Occur Conditions to Avoid: None known. ________________________________________________________________________________________________________________________ VII - HEALTH HAZARD DATA Routes of entry during normal usage: Inhalation? YES Skin? YES Ingestion? NO Health Hazards: Acute: No effects are suspected under normal professional use. Chronic: None known. Carcinogenicity: NTP - NO IARC - NO OSHA - NO Signs and Symptoms of Overexposure: No effects are suspected under normal professional use. Medical Conditions That Can Be Aggravated by Exposure: Allergies, skin and respiratory disorders. Product sensitivity. ________________________________________________________________________________________________________________________ VIII - EMERGENCY AND FIRST AID PROCEDURE Eyes: Flush with cool water for 15 minutes while holding eyelid open. If irritation persists, seek medical attention immediately. Skin: Avoid contact with skin. Remove contaminated clothing. Wash affected area thoroughly with soap and water. If irritation persists, seek immediate medical attention. Inhalation: Remove to fresh air if allowable concentrations of any of the hazardous ingredients are exceeded. If not breathing, trained personnel should initiate artificial respirations and immediate medical attention should be obtained. Ingestion: Do not induce vomiting. Do not give anything by mouth to an unconscious person. Seek medical attention immediately. ________________________________________________________________________________________________________________________ IX - PRECAUTIONS FOR SAFE HANDLING AND USE Steps to be taken if Material is Leaked or Spilled: Wear protective equipment. Contain by diking with inert absorbent materials and put into an approved waste container. Waste Disposal Method: Dispose in accordance to local environmental regulation. Precautions to be taken during Handling and Storage: Keep container closed when not in use. Store at 60-95°F (15-35°C) and out of the sun. Use adequate ventilation to avoid breathing vapors when cover is removed. Avoid prolonged skins contact. Other Precautions: _______________________________________________________________________________________________________________________ X - CONTROL MEASURES Respiratory Protection: If workplace exposure limit of product is exceeded, a NIOSH/MSHA approved air supplied respirator is required in absence of proper environmental control. Engineering or administrative controls should be implemented to reduce exposure. Local Exhaust - Use in WELL VENTILATED areas only. Mechanical - Use only intrinsically safe devices. Ventilation: Special - N/A Other - N/A Eye Protection: Safety glasses or goggles as necessary to prevent eye contact. Protective Gloves: Impervious. (Nitrile, rubber, or better) As needed to minimize contact with skin. Other Protective Equipment: _______________________________________________________________________________________________________________________ N/A="Not Applicable" N/E="Not Established" The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the use thereof. MAPEI assumes no responsibility for personal injury or property damage to vendees, users, or third parties caused by the material. Such vendees or users assume all risks associated with the use of the material. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------English Version on pages 2 and 3. Page 3 of 7 Ultrabond ECO™ 575 Version Française à la pages 4 et 5. La versión en Español en las páginas 6 y 7. MSDS Page 3 de 7 Páginas 3 de 7
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-701 Modify Date : 2005:09:19 20:16:40-04:00 Create Date : 2005:09:19 20:16:27-04:00 Metadata Date : 2005:09:19 20:16:40-04:00 Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Title : Unified MAPEI MSDS Creator : DHouse Document ID : uuid:ed95b42b-34a5-41b0-9a79-5ed1665cddf0 Instance ID : uuid:f093e081-ce1b-45ab-8ee7-91ca11ed7d59 Producer : Acrobat Distiller 6.0 (Windows) Page Count : 2 Author : DHouseEXIF Metadata provided by EXIF.tools