CL2500 Instruction Manuals MASTER Installation Directions

: Pdf 622636-Installationsheet 622636-InstallationSheet 092644 Batch5 unilog

Open the PDF directly: View PDF .
Page Count: 2

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

www.kleintools.com

139677 Rev. 11/13 B

ENGLISH

• 1000A AC/DC

• TRUE RMS

• AUTO / MANUAL

RANGE

• NON CONTACT

VOLTAGE TESTER

• MAX / MIN / HOLD

• ANALOG BAR GRAPH

• 3-5/6 DIGIT

5999 COUNT LCD

• BACKLIGHT

• WORKLIGHT

ENGLISH

8. Non Contact Voltage (NCV): > 25V AC

SYMBOLS USED ON LCD

~

AC Measurement DC Measurement

-

Negative DC Value

AT

Auto Range Active

O

.L.

Overload: Range Exceeded Apo

Auto Power-Off Active

Low Battery

HOLD

Hold Active

MIN

Minimum Reading

M

AX

Maximum Reading

%

Duty Cycle Mode Frequency Mode

V

Voltage Measurement

A

Current in Amps

Ω

Resistance in Ohms Diode Test

F

Capacitance in Farads Continuity Test

Relative / Zero Mode

n

Nano 10

-9

µ

Micro 10

-6

m

Milli 10

-3

k

Kilo 10

3

M

Mega 10

6

ELECTRICAL SPECIFICATIONS

DC Voltage Measurement

Range Resolution Accuracy

600mV ˜ 600V 0.1mV ˜ 0.1V ± (0.5% + 4 digits)

1000V 1V ± (0.8% + 10 digits)

Overload Protection: 1000V

AC Voltage Measurement

Range Resolution Accuracy

600mV ˜ 750V 0.1mV ˜ 1V ± (2.0% + 5 digits)

Overload Protection: 750V RMS

Frequency Response: 45 to 400 Hz

Minimum Voltage for Frequency Measurement: 200mV

Response: True RMS

DC Current Measurement

Range Resolution Accuracy

600µA 0.1µA ± (1.2% + 3 digits)

2000µA 1µA

60A 0.01A ± (2.5% + 15 digits)

600A ~ 1000A 0.1A ~ 1A ± (1.5% + 8 digits)

Overload Protection:

• Voltage: 600V RMS

• Current: 2000µA (leads), 1000A (clamp)

AC Current Measurement

Range Resolution Accuracy

600µA 0.1µA ± (2.0% + 5 digits)

2000µA 1µA ± (1.5% + 5 digits)

60A 0.01A ± (2.9% + 15 digits)

600A ~ 1000A 0.1A ~ 1A ± (1.9% + 8 digits)

Overload Protection:

• Voltage: 600V RMS

• Current: 2000µA (leads), 1000A (clamp)

Frequency: 45 to 400Hz

Minimum Current for Frequency Measurement: 400µA (leads) or 20A (clamp)

Response: True RMS

Resistance Measurement

Range Resolution Accuracy

600Ω ˜ 6MΩ0.1Ω ˜ 0.001MΩ ± (1.0% + 4 digits)

60MΩ0.01MΩ± (2.0% + 4 digits)

Overload Protection: 600V RMS

Capacitance Measurement

Range Resolution Accuracy

60nF ˜ 6000µF 0.01nF ˜ 1µF ± (3.5% + 6 digits)

Overload Protection: 600V RMS

Frequency Measurement

Range Resolution Accuracy

99.99Hz ˜ 499.9kHz 0.01Hz ˜ 100Hz ± (0.1% + 4 digits)

Overload Protection: 600V RMS

Duty Cycle Measurement

Range Resolution Accuracy

0.1 ˜ 99.9% 0.1% ± (0.2% per kHz + 0.1% + 5 digits)

Overload Protection: 600V RMS

Diode Test

Overload Protection Range Test Current Open Circuit Voltage

600V RMS 6.0V Appx. 0.25mA < 1.8V DC

Continuity Test

Overload Protection Open Circuit Voltage Threshold (Appx.)

600V RMS < 0.44V ~40Ω

Non Contact Voltage Detector

On Voltage

Appx. 25V AC and above



WARRANTY

www.kleintools.com/warranty

CLEANING

Turn instrument off and disconnect test leads. Clean the instrument by using

a damp cloth. Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when instrument is not in use for a prolonged period of

time. Do not expose to high temperatures or humidity. After a period of storage

in extreme conditions exceeding the limits mentioned in the Specifications

section, allow the instrument to return to normal operating conditions before

using it.

DISPOSAL / RECYCLE

Caution: This symbol indicates that equipment and its accessories

shall be subject to a separate collection and correct disposal.

750V

1000V

1000A

Dwg Name: CL2500-139677ART Dwg No: 139677

ECO No: 14678 Pkg Dwg Ref: 1650 Rev: B

Color Reference: CEN-PACK-003-A

Instruction Manual

CL2500

CL2500 Instruction Manuals - MASTER.indd 1-4 11/20/2013 2:57:08 PM

ENGLISH

5. Resistance:

< 60MΩ

Features:

MAX/MIN

RANGE

HOLD

I

J

FEATURE DETAILS

CL2500

Instruction Manual

GENERAL SPECIFICATIONS

The Klein Tools CL2500 is a True RMS, auto-ranging clamp meter. It measures

AC / DC voltage, AC / DC current, resistance, capacitance, frequency, and duty

cycle. It can also test non-contact voltage, diodes, and continuity.

• Operating Altitude: 2000 meters

• Storage Altitude: 10000 meters

• Humidity: 0% to 80% at 32°F to 95°F (0°C to 35°C)

0% to 70% at 32°F to 131°F (0°C to 55°C)

• Operating Temperature: 0°C / 32°F to 40°C / 104°F < 75% R.H.

• Storage Temperature: -20°C / -4°F to 60°C / 140°F

• Accuracy Temperature: 18°C / 64°F to 28°C / 82°F

• Temperature Coefcient: 0.1*(specified accuracy) / °C

• Dimensions: 8.09" x 2.56" x 1.38" (205 mm x 65 mm x 35 mm)

• Weight: 14 oz. (400 g)

• Calibration: Accurate for one year

• Certications: UL & cUL standard UL3111-1 Listed

• Pollution Degree: 2

• Accuracy: ± (% of reading + # of least significant digits)

• Ingress Protection: IP42

• Drop Protection: 1 m (3 ft.)

• Safety Rating: CATIII 1000V, CAT IV 600V

WARNINGS

To ensure safe operation and service of the tester, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

• Before each use, verify meter operation by measuring

a known voltage or current.

• Never use the meter on a circuit with voltages that exceed the

category based rating of this meter.

• Do not use the meter during electrical storms, or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Ensure meter leads are fully seated, and keep fingers away from

the metal probe contacts when making measurements.

• Do not open meter to replace batteries while probes are connected.

• Use caution when working with voltages above 60V DC,

or 25V AC RMS. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock,

replace batteries if a low battery indicator appears.

• Unless measuring voltage or current, shut off and lock out

power before measuring resistance or capacitance.

• Always adhere to local and national safety codes. Use individual

protective equipment to prevent shock and arc blast injury where

hazardous live conductors are exposed.

SYMBOLS

~

AC Alternating Current Warning or Caution

DC Direct Current Dangerous levels

DC/AC Voltage or Current Double Insulated Class II

Ground Safe for disconnect

from live conductors

AC Source

A. Use CAT IV 600 rated leads or higher.

Do not attempt to measure more than 1000V DC or 750V AC or 2000µA.

B. Keep hands below line when measuring high current levels.

C. Auto Power-Off (Apo)

• Device will power off after 30 minutes non-use.

• Turn the dial or press a button to wake.

• Disabled during Max / Min function.

• Holding Select button while turning on disables Auto Power-Off.

D. Select Functionality Button

• Quick press (<0.5 sec):

»Switch between AC and DC.

»Switch between and .

• Long press (>1 sec):

»Switch between AC, Frequency, and Duty Cycle modes.

»Zero the DC current clamp reading.

E. Hold / Backlight / Worklight

• Press to hold the current input on the display.

• Press again to return to live reading.

• Press for 2 seconds to enable / disable lights.

• Using lights decreases battery life.

F. Auto / Manual Range

• Press repeatedly to cycle through manual ranges.

• Press for 2 seconds to return to auto ranging mode.

• AT is displayed on LCD only during auto ranging mode.

G. Max / Min Hold

• Press to enter Max / Min mode; the largest and smallest

values will be saved while in this mode.

• Press repeatedly to alternate between the maximum and minimum readings.

• Press for 2 seconds to return to live reading and clear

the stored maximum and minimum values.

H. I. Battery Replacement

• When indicator is displayed on the LCD, batteries must be

replaced.

• Remove the back screw and replace 2 x AAA batteries.

J. Magnetic Back

• Attach instrument to metal for hands-free use.

K. Bar Graph

• The bar graph shows an approximate analog representation

of a measurement.

• The bar graph responds much faster than the digital display.

• The scale of the bar graph is zero to the maximum reading of

the selected range.

FUNCTION INSTRUCTIONS

7

1

6

2

3

5

1. AC / DC Current (large): < 1000A

Features:

ZERO (DC)

MAX/MINRANGEHOLD

• Center wire in guides for best accuracy.

• Opposing currents cancel. Use line-splitter (USA only) when necessary.

2. AC / DC Current (small): < 2000µA

Features:

MAX/MINRANGEHOLD

• Select AC or DC current source.

• Current above 2000µA will damage instrument.

3. AC / DC Voltage: < 750V AC or 1000V DC

Features:

MAX/MINRANGEHOLD

• Select AC or DC voltage source.

4. Frequency (Hz) / Duty Cycle (See FEATURE DETAILS)

Features:

HOLD

• Select , , or setting.

• Do not measure resistance on a live circuit.

6. Capacitance:

< 6000µF

Features:

HOLD

• Safely discharge capacitor before measurement.

• Reading may take up to 60 seconds for large capacitors.

7. Diode / Continuity

Display shows:

• Forward voltage drop if forward biased.

• “O.L.” if reverse biased.

Diode Features:

• Display shows resistance.

• Buzzer sounds if less than 40Ω.

Continuity Features:

HOLD MAX/MIN

B

8

4

HOLD MAX/MIN

1

C

D

A

K

E

F

G

H

PRESIONE

Diodo Continuidad

PRESIONE

Diodo Continuidad

4

Dwg Name: CL2500-139677ART Dwg No: 139677

ECO No: 14678 Pkg Dwg Ref: 1650 Rev: B

Color Reference: CEN-PACK-003-A

CL2500 Instruction Manuals - MASTER.indd 5-8 11/20/2013 2:57:11 PM