Installation Directions

2014-10-17

: Pdf 79025-Installationsheet 79025-InstallationSheet Batch10 unilog

Open the PDF directly: View PDF PDF.
Page Count: 3

DownloadInstallation Directions
Open PDF In BrowserView PDF
BUL10256

ECP - SERIES

REV. D
PRE ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS FOR COUPLINGS AND SUPPORT
BRACKETS ON ECLIPSE COMMAND ENCLOSURES

A) CENTER THE SUPPORT BRACKET (PART 2)
ON WIDTH AND DEPTH OF THE
ENCLOSURE. SEE CHART BELOW. CLAMP
DOWN THE BRACKET AT THE LOCATION
GIVEN BELOW ON THE OUTSIDE OF THE
ENCLOSURE.

A (DEPTH OF
ENCLOSURE)

B) CHECK THE 3 DRILL PATTERNS ON PAGE 2
FOR THE PATTERN THAT APPLIES TO THE
COUPLING (PART 1) PURCHASED. USING
THE SUPPORT BRACKET AS A TEMPLATE,
MARK AND DRILL THROUGH THE ECP
ENCLOSURE AS SHOWN.

B

C) ASSEMBLE THE COUPLING TO THE
ENCLOSURE AS PRE-ASSEMBLY
INSRUCTIONS.
ECP #
ECP12126
ECP12168
ECP161610
ECP162010
ECP202412
ECP20246

ASSEMBLY INSTRUCTIONS

A
6" (152.5mm)
8" (203mm)
10" (254mm)
10" (254mm)
12" (305mm)
6" (152.5mm)

B
.125" (3.2mm)
1.125" (28.6mm)
2.125" (54mm)
2.125" (54mm)
3.125" (79.4mm)
.125" (3.2mm)

1/4 - 20 STUDS INSIDE
ECP ENCLOSURE

A) FASTEN SUPPORT BRACKET (PART 2) TO
THE INSIDE OF THE ECP ENCLOSURE
USING 1/4 - 20 KEP NUTS (PART 5) OVER
THE FOUR STUDS IN THE ENCLOSURE.

ECP
ENCLOSURE

1

B) ASSEMBLE THE COUPLING (PART 1) TO
THE ENCLOSURE WITH THE GASKET
(PART 3) TO OUTSIDE AND METAL RING
(PART 4) TO INSIDE AS SHOWN TO THE
RIGHT.

3

C) FASTEN THE COUPLING TO ENCLOSURE
USING 4 SOCKET SCREWS (PART 6).

PART # QTY.
DESCRIPTION
1
1
COUPLING
2
1
SUPPORT BRACKET
3
1
GASKET
4
1
METAL RING (ON 50
& 80 SERIES ONLY)
5
4
1/4 - 20 KEP NUT
6
4
M6 OR M8 SOCKET
SCREW

TOOL BOX

3/8 or 7/16" Socket
Wrench or Driver

5mm or 6mm
Allen Key

2

4

5

6

Tape
Measure

"C" Clamp

HAMMOND
MANUFACTURING

TM

ENCLOSURES
PAGE 1 OF 3

BUL10256

ECP - SERIES

REV. D

ASSEMBLY INSTRUCTIONS FOR COUPLINGS AND SUPPORT
BRACKETS ON ECLIPSE COMMAND ENCLOSURES
DRILLING INSTRUCTIONS

DRILLING PATTERN FOR TARA COUPLINGS

A) FASTEN THE SUPPORT
BRACKET (PART 2) AS
SHOWN ON PAGE 1 IN PRE
ASSEMBLY INSTRUCTIONS.
1.81

DRILL THE CENTER HOLE
B) AND THE 4 MOUNTING
HOLES IN THE SIZE AND
LOCATION SPECIFIED BY
THE COUPLINGS LISTED.

1.81

DRILL THRU
2.0" (50.8mm)
DIA

C) DE - BURR HOLES AND USE
THE TOUCH UP PAINT TO
COAT RAW EDGES.

USE INSIDE RADIUS
OF THE SLOT AS A
DRILL TEMPLATE,
DRILL THRU .28" (7mm)
DIA IN ENCLOSURE

D) ASSEMBLE THE COUPLING
TO THE ENCLOSURE AS
SHOWN ON PAGE 1.

DRILLING PATTERN FOR 80 SYSTEM COUPLINGS

DRILLING PATTERN FOR 50 SYSTEM COUPLINGS

3.42

2.284

3.42

2.284

DRILL THRU
2.0" (50.8mm)
DIA

CUT THRU TABS AND
SLOTS FOR 3.58" (91mm)
DIA HOLE

USE OUTSIDE RADIUS
OF THE SLOT AS A
DRILL TEMPLATE,
DRILL THRU .28" (7mm)
DIA IN ENCLOSURE

TOOL BOX

Centre
Punch

USE OUTSIDE HOLES
AS A DRILL TEMPLATE,
DRILL THRU .35" (9mm)
DIA IN ENCLOSURE

Hand File Drill, Use Bit Specified
In Drill Pattern

Cutting
Tool

Touch Up
Paint

HAMMOND
MANUFACTURING

TM

ENCLOSURES
PAGE 2 OF 3

BUL10256

ECP - SERIES
ASSEMBLY INSTRUCTIONS FOR REMOVAL OF ALUMINUM
FRONT PANEL ON ECLIPSE COMMAND ENCLOSURES

REV. D
NOTE: REAR DOOR ON ECP ENCLOSURE.
IF THE REAR DOOR IS REVERSED FROM R.H. HINGE TO
L.H. HINGE (WHEN FACING THE REAR OF THE ENCLOSURE),
REMOVE THE HINGE PINS, REMOVE THE 1/4 TURN LATCH,
ROTATE 90 DEGREES COUNTER CLOCK WISE THEN
REINSTALL (SEALING WASHER IN PLACE) THROUGH THE
HOLE IN THE DOOR. INSTALL LARGE RETAINING NUT AND
TORQUE TO 190 INLB (CAM MUST TURN UP IN UNLATCHED
POSITION). INSTALL HINGE PINS FROM TOP TO BOTTOM.

PART # QTY.
1
1

5
4

2

1

3

4

4

4

5
6

4
1

6

DESCRIPTION
ALUMINUM
FACE PANEL
FRONT FRAME
EXTRUSION
5M SOCKET
SCREW
SEALING
WASHER
M5 HEX NUT
SEALING
GASKET

1

2

3

M5 SOCKET SCREWS ARE SECURED IN
THE FRAME. IF ONE LOOSENS WHILE
REMOVING THE PANEL, RERIGHTEN
BEFORE RE-ASSEMBLY. SEE STEP C.
ASSEMBLY INSTRUCTIONS
A) OPEN THE REAR DOOR TO ACCESS THE MOUNTING HARDWARE (PARTS 3, 4 & 5)
THAT FASTEN THE ALUMINUM FACE PANEL (PART 1) AND FRONT FRAME
EXTRUSION (PART 2) TO THE ECP ENCLOSURE. THE HEX NUTS AND SEALING
WASHERS ARE LOCATED IN EACH CORNER ON THE INSIDE OF THE ENCLOSURE.
B) UNDO HEX NUTS AND THE SEALING WASHERS AND REMOVE THE FRONT PANEL
AND THE FRONT FRAME EXTRUSION FROM THE ENCLOSURE. CHECK THAT THE
SEALING GASKET (PART 6) IS NOT DAMAGED. SEE NOTE ON
"BEFORE RE-ASSEMBLY".
C) IF A M5 SOCKET SCREW LOOSENS WHILE REMOVING THE PANEL, RE-TIGHTEN
BEFORE ASSEMBLING USING A 2.5mm ALLEN KEY.
D) AFTER REWORKING THE FRONT PANEL, ASSEMBLE THE FACE PANEL AND THE
FRONT FRAME EXTRUSION TO THE ENCLOSURE USING HEX NUTS AND SEALING
WASHERS. TORQUE HEX NUTS TO 30 IN/LB.
TOOL BOX

8mm Socket
Wrench or Driver

BEFORE RE-ASSEMBLY
CAUTION: CHECK THE
GASKET ON THE ENCLOSURE
SURFACE FOR DAMAGE
BEFORE RE-ASSEMBLY. IF THE
GASKET IS CUT OR TORN,
CONTACT HAMMOND
MANUFACTURING FOR
IMMEDIATE REPLACEMENT.
SEE STEP B.

HAMMOND
MANUFACTURING

2.5mm
Allen Key

TM

ENCLOSURES
PAGE 3 OF 3
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
Producer                        : GPL Ghostscript 8.54
Create Date                     : 2009:06:22 07:43:40
Modify Date                     : 2009:06:22 07:43:40
Title                           : 
Creator                         : PScript5.dll Version 5.2.2
Author                          : ekozak
Subject                         :
EXIF Metadata provided by EXIF.tools

Navigation menu