Installation Directions

2014-10-17

: Pdf 79025-Installationsheet 79025-InstallationSheet Batch10 unilog

Open the PDF directly: View PDF PDF.
Page Count: 3

HAMMOND
MANUFACTURING
TM
ENCLOSURES
TOOL BOX
BUL10256
ECP - SERIES
ASSEMBLY INSTRUCTIONS FOR COUPLINGS AND SUPPORT
BRACKETS ON ECLIPSE COMMAND ENCLOSURES
REV. D
PAGE 1 OF 3
1/4 - 20 STUDS INSIDE
ECP ENCLOSURE
1
3
4
65
2
CENTER THE SUPPORT BRACKET (PART 2)
ON WIDTH AND DEPTH OF THE
ENCLOSURE. SEE CHART BELOW. CLAMP
DOWN THE BRACKET AT THE LOCATION
GIVEN BELOW ON THE OUTSIDE OF THE
ENCLOSURE.
CHECK THE 3 DRILL PATTERNS ON PAGE 2
FOR THE PATTERN THAT APPLIES TO THE
COUPLING (PART 1) PURCHASED. USING
THE SUPPORT BRACKET AS A TEMPLATE,
MARK AND DRILL THROUGH THE ECP
ENCLOSURE AS SHOWN.
ASSEMBLE THE COUPLING TO THE
ENCLOSURE AS PRE-ASSEMBLY
INSRUCTIONS.
PART # QTY. DESCRIPTION
1 1 COUPLING
2 1 SUPPORT BRACKET
3 1 GASKET
4 1 METAL RING (ON 50
& 80 SERIES ONLY)
5 4 1/4 - 20 KEP NUT
6 4 M6 OR M8 SOCKET
SCREW
ASSEMBLY INSTRUCTIONS
A)
B)
C)
A (DEPTH OF
ENCLOSURE)
B
FASTEN SUPPORT BRACKET (PART 2) TO
THE INSIDE OF THE ECP ENCLOSURE
USING 1/4 - 20 KEP NUTS (PART 5) OVER
THE FOUR STUDS IN THE ENCLOSURE.
ASSEMBLE THE COUPLING (PART 1) TO
THE ENCLOSURE WITH THE GASKET
(PART 3) TO OUTSIDE AND METAL RING
(PART 4) TO INSIDE AS SHOWN TO THE
RIGHT.
FASTEN THE COUPLING TO ENCLOSURE
USING 4 SOCKET SCREWS (PART 6).
3/8 or 7/16" Socket
Wrench or Driver
5mm or 6mm
Allen Key Tape
Measure "C" Clamp
ECP # A B
ECP12126 6" (152.5mm) .125" (3.2mm)
ECP12168 8" (203mm) 1.125" (28.6mm)
ECP161610 10" (254mm) 2.125" (54mm)
ECP162010 10" (254mm) 2.125" (54mm)
ECP202412 12" (305mm) 3.125" (79.4mm)
ECP20246 6" (152.5mm) .125" (3.2mm)
PRE ASSEMBLY INSTRUCTIONS
A)
B)
C)
ECP
ENCLOSURE
HAMMOND
MANUFACTURING
TM
ENCLOSURES
TOOL BOX
BUL10256
ECP - SERIES
ASSEMBLY INSTRUCTIONS FOR COUPLINGS AND SUPPORT
BRACKETS ON ECLIPSE COMMAND ENCLOSURES
REV. D
PAGE 2 OF 3
FASTEN THE SUPPORT
BRACKET (PART 2) AS
SHOWN ON PAGE 1 IN PRE
ASSEMBLY INSTRUCTIONS.
DRILL THE CENTER HOLE
AND THE 4 MOUNTING
HOLES IN THE SIZE AND
LOCATION SPECIFIED BY
THE COUPLINGS LISTED.
DE - BURR HOLES AND USE
THE TOUCH UP PAINT TO
COAT RAW EDGES.
ASSEMBLE THE COUPLING
TO THE ENCLOSURE AS
SHOWN ON PAGE 1.
DRILLING INSTRUCTIONS
A)
B)
C)
D)
DRILL THRU
2.0" (50.8mm)
DIA
USE INSIDE RADIUS
OF THE SLOT AS A
DRILL TEMPLATE,
DRILL THRU .28" (7mm)
DIA IN ENCLOSURE
1.81
1.81
2.284
2.284 3.42 3.42
USE OUTSIDE RADIUS
OF THE SLOT AS A
DRILL TEMPLATE,
DRILL THRU .28" (7mm)
DIA IN ENCLOSURE
DRILL THRU
2.0" (50.8mm)
DIA CUT THRU TABS AND
SLOTS FOR 3.58" (91mm)
DIA HOLE
USE OUTSIDE HOLES
AS A DRILL TEMPLATE,
DRILL THRU .35" (9mm)
DIA IN ENCLOSURE
DRILLING PATTERN FOR 50 SYSTEM COUPLINGS DRILLING PATTERN FOR 80 SYSTEM COUPLINGS
Centre
Punch
Touch Up
Paint
Drill, Use Bit Specified
In Drill Pattern
Hand File Cutting
Tool
DRILLING PATTERN FOR TARA COUPLINGS
HAMMOND
MANUFACTURING
TM
ENCLOSURES
TOOL BOX
BUL10256
ECP - SERIES
ASSEMBLY INSTRUCTIONS FOR REMOVAL OF ALUMINUM
FRONT PANEL ON ECLIPSE COMMAND ENCLOSURES
REV. D
PAGE 3 OF 3
OPEN THE REAR DOOR TO ACCESS THE MOUNTING HARDWARE (PARTS 3, 4 & 5)
THAT FASTEN THE ALUMINUM FACE PANEL (PART 1) AND FRONT FRAME
EXTRUSION (PART 2) TO THE ECP ENCLOSURE. THE HEX NUTS AND SEALING
WASHERS ARE LOCATED IN EACH CORNER ON THE INSIDE OF THE ENCLOSURE.
UNDO HEX NUTS AND THE SEALING WASHERS AND REMOVE THE FRONT PANEL
AND THE FRONT FRAME EXTRUSION FROM THE ENCLOSURE. CHECK THAT THE
SEALING GASKET (PART 6) IS NOT DAMAGED. SEE NOTE ON
"BEFORE RE-ASSEMBLY".
IF A M5 SOCKET SCREW LOOSENS WHILE REMOVING THE PANEL, RE-TIGHTEN
BEFORE ASSEMBLING USING A 2.5mm ALLEN KEY.
AFTER REWORKING THE FRONT PANEL, ASSEMBLE THE FACE PANEL AND THE
FRONT FRAME EXTRUSION TO THE ENCLOSURE USING HEX NUTS AND SEALING
WASHERS. TORQUE HEX NUTS TO 30 IN/LB.
ASSEMBLY INSTRUCTIONS
A)
B)
C)
D)
8mm Socket
Wrench or Driver
2.5mm
Allen Key
NOTE: REAR DOOR ON ECP ENCLOSURE.
IF THE REAR DOOR IS REVERSED FROM R.H. HINGE TO
L.H. HINGE (WHEN FACING THE REAR OF THE ENCLOSURE),
REMOVE THE HINGE PINS, REMOVE THE 1/4 TURN LATCH,
ROTATE 90 DEGREES COUNTER CLOCK WISE THEN
REINSTALL (SEALING WASHER IN PLACE) THROUGH THE
HOLE IN THE DOOR. INSTALL LARGE RETAINING NUT AND
TORQUE TO 190 INLB (CAM MUST TURN UP IN UNLATCHED
POSITION). INSTALL HINGE PINS FROM TOP TO BOTTOM.
3
M5 SOCKET SCREWS ARE SECURED IN
THE FRAME. IF ONE LOOSENS WHILE
REMOVING THE PANEL, RERIGHTEN
BEFORE RE-ASSEMBLY. SEE STEP C.
5
4
6
1
2
PART # QTY. DESCRIPTION
1 1 ALUMINUM
FACE PANEL
2 1 FRONT FRAME
EXTRUSION
3 4 5M SOCKET
SCREW
4 4 SEALING
WASHER
5 4 M5 HEX NUT
6 1 SEALING
GASKET
BEFORE RE-ASSEMBLY
CAUTION:
CHECK THE
GASKET ON THE ENCLOSURE
SURFACE FOR DAMAGE
BEFORE RE-ASSEMBLY. IF THE
GASKET IS CUT OR TORN,
CONTACT HAMMOND
MANUFACTURING FOR
IMMEDIATE REPLACEMENT.
SEE STEP B.

Navigation menu