906292 Instructions
906293 Instructions 906293_Instructions 906293_Instructions product s sunlightsupply 3:
906306 Instructions 906306_Instructions 906306_Instructions product s sunlightsupply 3:
906308 Instructions 906308_Instructions 906308_Instructions product s sunlightsupply 3:
2018-09-20
: Pdf 906292 Instructions 906292_Instructions product s
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
PRO SUN ™ 1000 W DE COMMERCIAL FIXTURE LAMP INCLUDED Installation & Operating Instructions 120-240 VOLT, 277 VOLT, 277-347 VOLT OR 480 VOLT (Part# 906292) 120-240 Volt Fixture: Includes 6.5 ft. Convertible Smart Volt™ Dual Ferrite power cord with 120 and 240 volt plugs to convert to 120-240 volt cord. (Part# 906293) 277 Volt Fixture: Includes 8 ft. hardwired power cord with a L7-15p twist lock plug. (Part# 906306) 277-347 Volt Fixture: Includes 8 ft. hardwired power cord with a L24-20p twist lock plug. (Part# 906308) 480 Volt Fixture: Includes 8 ft. hardwired power cord with a L8-20p twist lock plug. READ THESE INSTRUCTIONS BEFORE FIRING UP YOUR FIXTURE KEEP ORIGINAL PACKAGING: All returns need to be in the original packaging in order to avoid product damage during shipping. Any damage to products not in their original packaging will not be covered under warranty. SAFETY FIRST! Failure to observe the following safety warnings may result in serious injury. In addition, failure to observe these safety warnings will result in a waiver of all liabilities and will void all warranties. WARNING: If the exterior of the lamp is damaged, replace lamp immediately. When re-lamping, make sure lamp has time to cool before touching. Make sure power cord is connected properly. Disconnect power before re-lamping. DO NOT hang by power or lamp cord. DO NOT make contact with the interior of the socket while power is on. DO NOT operate light systems in wet locations. D O NOT plug system into supply voltage other than what is designated on ballast. D O NOT attempt to rewire or reconfigure your system, it will void warranty and could cause serious safety hazards (i.e. power cord, lamp cord, lamp socket or ballast). Keep away from children. Sun System Pro Sun 1000 W DE Commercial FIXTURE SYSTEM SETUP : 1. Remove the system from the box along with all additional parts. 2. These systems do not require much setup. 3. Insert a DE lamp into a DE reflector. (FIG. 1) Insert each lamp wire of the double-ended lamp into both socket slots. Make sure the wires are straight. Push both ends of lamp firmly down into the metal clips. Slide each socket slider lock over both ends of the lamp to secure the lamp into place. 4. Hang the fixture using eye bolts or some other means of securely hanging from the ceiling. Sun Grip® Push Button Light Hangers (#710122, #710114, #710116 & #710123), (FIG. 2), Sky Hook® Light Hangers (#710119) or jack chain (#350205) may be used to adjust the hanging height. 5. Plug the unit into the proper NEMA configured receptacle or hardwire unit depending on model voltage. FIG. 1 Push both ends of lamp firmly down into the metal clips. FIG. 2 Slide both sockets in the locked position for a secure lamp. SLIDE THIS W AY SLIDE SOCKET LOCK ALL THE WAY UNTIL IT STOPS HERE SAFETY FIRST! D O NOT alter or modify this unit in any way. It may cause bodily injury or death as this is a high power electrical device. DO NOT submerse in water or splash water on the unit. DO NOT plug or unplug the lamp cord while the ballast is energized. These high performance, ultra high frequency electronic ballasts are extremely efficient. They have a high power factor and high luminous efficacy. It’s stable performance creates constant power output even when power fluctuates (power surge). Short circuit protection technology prevents damage to the lamp and other ballasts connected to the same circuit. 2 1. INSTALLATION PROCEDURE D O NOT alter or modify the electronic ballast in any way. Not only may it damage the unit, it will void the warranty. Lamp power rating must match electronic ballast power rating. 120-240 VOLT FIXTURE Connect appropriate AC power plug here 120-240 Volt Fixture: Includes 6.5 ft. Convertible Smart Volt™ Dual Ferrite power cord with 120 and 240 volt plugs to convert to 120-240 volt cord. 277, 347 AND 480 VOLT FIXTURE 277 Volt Fixture: Includes 8 ft. hardwired power cord with a L7-15p twist lock plug. 347 Volt Fixture: Includes 8 ft. hardwired power cord with a L24-20p twist lock plug. 480 Volt Fixture: Includes 8 ft. hardwired power cord with a L8-20p twist lock plug. 2. SPECIFICATIONS 120, 208, 240, 277, 347 and 480 volt Power source frequency: 50/60 Hz Power Factor (cosø): > 0.97 Ambient Temp: 50˚ F to 120˚ F Crest Factor: < 1.6 Acoustic Resonance: none Total Harmonic Distortion (THD): < 10.0% 3. NOTES T his Sun System Pro Sun 1000 W DE Commercial Fixture is designed to operate 1000 watt double-ended H.I.D. lamps. T his unit offers short-circuit and power fluctuation protection. Features internal built-in circuit breaker. 240 V WIRING - VERY IMPORTANT All digital ballasts may malfunction if the 240 volt circuit has a neutral. The input for the ballast is 2 HOT WIRES and 1 GROUND WIRE. If you are using a light controller ONLY bring a ground wire and two hot leads from your electrical panels. HOT RESTRIKE The Sun System Pro Sun 1000 W DE Commercial Fixture features a hot restrike function to protect the lamp and ballast. This function allows the ballast to reignite the lamp once it has cooled. In the event of a power interruption or failed ignition the ballast will wait one minute and attempt to restart the lamp. If the lamp does not ignite at that time it will make four more attempts in five minute intervals. If the ballast has ran though the complete sequence (1 minute -5 minutes -5 minutes -5 minutes -5 minutes) the ballast will go into a locked mode. The ballast will not begin the ignition sequence again until it has been disconnected from power. This can be achieved by unplugging the ballast and plugging it back in or waiting until the next set timer cycle. Do not unplug the ballast until it has completed the full twenty-six minute sequence. 3 LAMP REPLACEMENT - Be sure to disconnect the power source before changing lamps. Always use the specified wattage lamp. TIMER BOX - If you are connecting a 240, 277, 347 or 480 volt fixture to a timer box, please make sure that it cuts off both legs when timer is switched off. If you continue to supply 120 volt to your ballast when the timer is switched off, it may damage your ballast. ERROR CODES - If the ballast encounters any abnormal conditions the built-in self-diagnostic feature will display easily identifiable error codes. Error codes can be identified by the number of flashes made by the green LED marked “turbo”. 1 Flash = Ballast Protection: This code means that the ballast has gone into a locked mode to protect itself. This may be followed by another code to help troubleshoot the cause. 2 Flash = Bad Lamp/Short Circuit: This code means that the ballast has a bad connection somewhere between the ballast and lamp. Reasons can include a bad lamp, loose lamp, loose lamp cord, a short in the cord or reflector, or a short in the ballast receptacle. 3 Flash = Low Voltage: This code means the power coming from the outlet to your ballast is not sufficient to power the unit. 4 Flash = Over Temperature: This code means the ballast has shut itself off due to overheating (>140° F). 5 Flash = Over Voltage: This code means the power from the outlet to your ballast has exceeded the maximum allowed voltage. 6 Flash = Lamp Fault: Incorrect/non compatible lamp will not work with ballast. CONTROL UP TO 400 SUN SYSTEM DOUBLE-ENDED COMMERCIAL FIXTURES OR OTHER COMPATIBLE MODELS WITH ONE ETELLIGENT CONTROLLER! The Sun System 1 Etelligent digital lighting controller enables the grower to control up to 400 fixtures. Features an industry first, ability to control any Sun System Etelligent compatible fixture or ballast with the same controller, operating on separate channels. This two channel controller allows daisy-chaining up to 200 fixtures per zone. Enabling complete control of your growing environment with timed on/off switching, sunrise/sunset, accurate temperature readings with dual thermal probes and thermal-threshold auto dim-shutdown for additional protection. ZONE A (up to 200 fixtures) 4 ZONE B (up to 200 fixtures) Sun System 1 Etelligent Controller Kit #902245 allows wired control of the on/off dimming capabilities. Complete kit includes: 1 Etelligent Controller, 1 universal power adapter 5 ft/1.5 m cable, 2 each 16 ft/5 m signal wires with ferrites for connection from controller to ballast and 2 each 16 ft/5 m temperature probes. TROUBLESHOOTING GUIDE Follow the troubleshooting tips below. If troubleshooting techniques fail, bring ballast back to your place of purchase to request warranty service. POSSIBLE CAUSES CORRECTIVE MAINTENANCE LAMP LOOSE IN SOCKETS Make sure that the lamp is fully inserted into the socket and that the socket is in the closed position. INCORRECT VOLTAGE Make sure you are using the correct input voltage with fixture. If using incorrect voltage, disconnect the fixture from the power source immediately. DEFECTIVE OR IMPROPER WIRING Examine wiring to ensure it agrees with wiring diagrams on fixture label. Check connections to see that they are secure. If wiring a 240 volt fixture, DO NOT use a neutral. The correct wiring is two hot wires and a ground. POOR ELECTRICAL CONNECTIONS Check wiring and lamp contact with socket. Make sure the lamp cord is firmly seated in output receptacle. INCORRECT LAMP LAMP DAMAGE Verify that you are using a 1000 W double-ended lamp. Investigate possibility of outer bulb damage. Look for broken tubes or loose metal parts. Replace lamp. FCC compliance This device complies with Part 18 of the FCC Rules. Advisory statement This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45-30 MHz. The interference potential of the device or system The interference potential of the device or system is the operating frequency; 110 kHz. Maintenance of the system Unplug the unit, wait 30 seconds, and plug the unit back in. Simple measures that can be taken by the user to correct interference Move the unit away from any radio device. This product contains delicate electronic components. This means that if it is placed near an object that transmits radio signals, it could cause interference. This could be, for example, mobile telephones, walkie talkies, CB radios, remote controls and microwaves. If interference occurs, move such objects away from the appliance. Sun System Pro Sun 1000 W DE Commercial Fixture. Compliant with FCC Part 18 Class A (governs commercial use) and FCC Part 18 Class B (governs residential use) as tested by an independent US testing lab in a true as used configuration. In our case, Northwest EMC or ElectroMagnetic Investigations, Hillsboro OR. This installation guide does not supersede national, state, or local regulations for electrical installations. TROUBLESHOOTING… IF YOUR FIXTURE DOES NOT WORK: 1. CHECK YOUR ELECTRICAL SOURCE: Make sure the unit is plugged in properly and that the breaker is not tripped or fuse blown. 2. CHECK THE LAMP COLOR: Make sure the lamp is fully seated in the socket. 5 WARRANTY SERVICE: Please read warranty information first. If after troubleshooting problems the light will still not work, you should return the light to the dealer where you purchased it. They will be able to further evaluate the light and test its various components and quite possibly will be able to identify and/or fix any problems. Often the problem is as simple as a defective lamp. If the dealer is unable to fix the light, they will return it to us for factory repair. Many dealers have loaner fixtures that you may check out until yours is returned (usually not more than 7-10 days). Please complete the “Dealer Search” on our website to locate the dealer nearest you. To located dealers within the United States: www.HawthorneGC.com. To located dealers within Canada: www.HawthorneGC.ca. If there are no dealers in your area, you may contact us directly for technical support. If we cannot help you resolve the problem over the phone, we will issue you a RMA # (return merchandise authorization) authorizing you to return the system to us for factory reconditioning (if the unit is under warranty). You will need to provide an email address or fax number so that the Authorization Form may be sent to you. You will need to include this Authorization Form in the packaging when returning your Sun System Pro Sun unit. Also please write the RMA # on the outside of the box. Please package the light carefully in its original packaging. If it is damaged in shipment we will not be responsible. Once we receive the light, we will repair it within 48 hours (business) and return it to you via UPS Ground. If the unit cannot be repaired, a replacement will be sent. If there are no replacements available, a comparable unit will be sent back. IMPORTANT: PROOF OF PURCHASE REQUIRED FOR RETURNS SUN SYSTEM PRO SUN 1000 W DE COMMERCIAL FIXTURE: 3 Year Warranty Returning Units: Please contact your retail store for returns. WARRANTY INFORMATION: The Hawthorne Gardening Company warrants to the original purchaser of this product against defects in material and workmanship under normal use for 3 year on SUN SYSTEM PRO SUN 1000 W DE COMMERCIAL FIXTURE. During the warranty period, The Hawthorne Gardening Company will, at our option, and without charge, repair or replace this product if the unit or any of its components fail or malfunction. This warranty is expressly in lieu of all other warranties, expressed or implied, including the warranties of merchantability and fitness for use and of all other obligations or liabilities on the part of the seller. This warranty shall not apply to this product or any part thereof which has been damaged by accident, abuse, misuse, modification, negligence, alteration or misapplication. The Hawthorne Gardening Company makes no warranty whatsoever in respect to accessories or parts not supplied by The Hawthorne Gardening Company. This warranty shall apply only to the United States, including Alaska, Hawaii, territories of the United States and Canada. NOTE: The Hawthorne Gardening Company is a manufacturer of supplementary lighting 6 systems. All sales offerings to the public are done through a nationwide group of dealers. No sales offerings will be made directly to the general public. NOTES _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ 7 NOTES _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ Manufactured for Hawthorne Hydroponics LCC, a subsidiary of The Hawthorne Gardening Company 3204 NW 38th Circle, Vancouver, WA 98660 | ©2018 HawthorneGC.com | HawthorneGC.ca 080318LM _________________________________________________________________________
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Language : en-US XMP Toolkit : Adobe XMP Core 5.6-c143 79.161424, 2017/09/22-11:52:47 Create Date : 2018:08:03 14:22:04-07:00 Metadata Date : 2018:08:03 14:22:06-07:00 Modify Date : 2018:08:03 14:22:06-07:00 Creator Tool : Adobe InDesign CC 13.1 (Macintosh) Instance ID : uuid:992718c9-8309-0b4f-8013-ecb623939f8d Original Document ID : xmp.did:87e97b9b-4bdf-481d-815c-923300646904 Document ID : xmp.id:a9bea3f1-a42e-4328-9ab0-18c2556bc7ba Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:19d51889-a185-435e-ba48-8c27d6282440 Derived From Document ID : xmp.did:01e5681c-1d3e-4e96-9a1b-da881a1b244d Derived From Original Document ID: xmp.did:87e97b9b-4bdf-481d-815c-923300646904 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 13.1 (Macintosh) History Changed : / History When : 2018:08:03 14:22:04-07:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 8 Creator : Adobe InDesign CC 13.1 (Macintosh)EXIF Metadata provided by EXIF.tools