906292 Instructions

Installation & Operating Instructions

120-240 VOLT, 277 VOLT, 277-347 VOLT OR 480 VOLT

READ THESE INSTRUCTIONS BEFORE FIRING UP YOUR FIXTURE

KEEP ORIGINAL PACKAGING: All returns need to be in the original packaging in order

to avoid product damage during shipping. Any damage to products not in their original

packaging will not be covered under warranty.

SAFETY FIRST!

Failure to observe the following safety warnings may result in serious injury. In addition, failure to

observe these safety warnings will result in a waiver of all liabilities and will void all warranties.

WARNING:

 If the exterior of the lamp is damaged, replace lamp immediately.

 When re-lamping, make sure lamp has time to cool before touching.

 Make sure power cord is connected properly.

 Disconnect power before re-lamping.

 DO NOT hang by power or lamp cord.

 DO NOT make contact with the interior of the socket while power is on.

 DO NOT operate light systems in wet locations.

  DO NOT plug system into supply voltage other than what is designated on ballast.

  DO NOT attempt to rewire or recongure your system, it will void warranty and could cause

serious safety hazards (i.e. power cord, lamp cord, lamp socket or ballast).

 Keep away from children.

(Part# 906292) 120-240 Volt Fixture: Includes 6.5 ft. Convertible Smart Volt™ Dual Ferrite power cord

with 120 and 240 volt plugs to convert to 120-240 volt cord.

(Part# 906293) 277 Volt Fixture: Includes 8 ft. hardwired power cord with a L7-15p twist lock plug.

(Part# 906306) 277-347 Volt Fixture: Includes 8 ft. hardwired power cord with a L24-20p twist lock plug.

(Part# 906308) 480 Volt Fixture: Includes 8 ft. hardwired power cord with a L8-20p twist lock plug.

LAMP INCLUDED

1000 W DE

COMMERCIAL FIXTURE

PRO SUN™

2

Sun System Pro Sun 1000 W DE Commercial

FIXTURE SYSTEM SETUP :

1. Remove the system from the box along with all additional parts.

2. These systems do not require much setup.

3. Insert a DE lamp into a DE reflector. (FIG. 1) Insert each lamp wire of the double-ended

lamp into both socket slots. Make sure the wires are straight. Push both ends of lamp

rmly down into the metal clips. Slide each socket slider lock over both ends of the

lamp to secure the lamp into place.

4. Hang the xture using eye bolts or some other means of securely hanging from the

ceiling. Sun Grip® Push Button Light Hangers (#710122, #710114, #710116 &

#710123), (FIG. 2), Sky Hook® Light Hangers (#710119) or jack chain (#350205)

may be used to adjust the hanging height.

5. Plug the unit into the proper NEMA congured receptacle or hardwire unit depending

on model voltage.

Push both ends of lamp rmly

down into the metal clips. Slide both sockets in the locked

position for a secure lamp.

SLIDE THIS WAY

SLIDE SOCKET

LOCK ALL THE WAY

UNTIL IT STOPS HERE

FIG. 1 FIG. 2

SAFETY FIRST!

  DO NOT alter or modify this unit in any way. It may cause bodily injury

or death as this is a high power electrical device.

 DO NOT submerse in water or splash water on the unit.

 DO NOT plug or unplug the lamp cord while the ballast is energized.

These high performance, ultra high frequency electronic ballasts are extremely efcient.

They have a high power factor and high luminous efcacy. It’s stable performance creates

constant power output even when power fluctuates (power surge). Short circuit protection

technology prevents damage to the lamp and other ballasts connected to the same circuit.

1. INSTALLATION PROCEDURE

  DO NOT alter or modify the electronic ballast in any way. Not only may it damage the

unit, it will void the warranty.

  Lamp power rating must match electronic ballast power rating.

3. NOTES

  This Sun System Pro Sun 1000 W DE Commercial Fixture is designed to operate

1000 watt double-ended H.I.D. lamps.

  This unit offers short-circuit and power fluctuation protection.

 Features internal built-in circuit breaker.

2. SPECIFICATIONS

  120, 208, 240, 277, 347 and 480 volt

  Power source frequency: 50/60 Hz

  Power Factor (cosø): > 0.97

  Ambient Temp: 50˚ F to 120˚ F

Crest Factor: < 1.6

 Acoustic Resonance: none

  Total Harmonic Distortion

(THD): < 10.0%

240 V WIRING - VERY IMPORTANT

All digital ballasts may malfunction if the 240 volt circuit has a neutral. The input for the

ballast is 2 HOT WIRES and 1 GROUND WIRE. If you are using a light controller ONLY bring

a ground wire and two hot leads from your electrical panels.

HOT RESTRIKE

The Sun System Pro Sun 1000 W DE Commercial Fixture features a hot restrike function

to protect the lamp and ballast. This function allows the ballast to reignite the lamp once

it has cooled. In the event of a power interruption or failed ignition the ballast will wait

one minute and attempt to restart the lamp. If the lamp does not ignite at that time it

will make four more attempts in ve minute intervals. If the ballast has ran though the

complete sequence (1 minute -5 minutes -5 minutes -5 minutes -5 minutes) the ballast

will go into a locked mode. The ballast will not begin the ignition sequence again until it

has been disconnected from power. This can be achieved by unplugging the ballast and

plugging it back in or waiting until the next set timer cycle. Do not unplug the ballast until

it has completed the full twenty-six minute sequence. 3

Connect appropriate

AC power plug here

120-240 VOLT FIXTURE

277, 347 AND 480 VOLT FIXTURE 277 Volt Fixture: Includes 8 ft. hardwired

power cord with a L7-15p twist lock plug.

347 Volt Fixture: Includes 8 ft. hardwired

power cord with a L24-20p twist lock plug.

480 Volt Fixture: Includes 8 ft. hardwired

power cord with a L8-20p twist lock plug.

120-240 Volt Fixture: Includes 6.5 ft. Convertible

Smart Volt™ Dual Ferrite power cord with 120 and

240 volt plugs to convert to 120-240 volt cord.

LAMP REPLACEMENT - Be sure to disconnect the power source before changing

lamps. Always use the specied wattage lamp.

TIMER BOX - If you are connecting a 240, 277, 347 or 480 volt xture to a timer box,

please make sure that it cuts off both legs when timer is switched off. If you continue to

supply 120 volt to your ballast when the timer is switched off, it may damage your ballast.

ERROR CODES - If the ballast encounters any abnormal conditions the built-in

self-diagnostic feature will display easily identiable error codes. Error codes can be

identied by the number of flashes made by the green LED marked “turbo”.

1 Flash = Ballast Protection: This code means that the ballast has gone into a

locked mode to protect itself. This may be followed by another code to help

troubleshoot the cause.

2 Flash = Bad Lamp/Short Circuit: This code means that the ballast has a bad

connection somewhere between the ballast and lamp. Reasons can include

a bad lamp, loose lamp, loose lamp cord, a short in the cord or reflector, or a

short in the ballast receptacle.

3 Flash = Low Voltage: This code means the power coming from the outlet to your

ballast is not sufcient to power the unit.

4 Flash = Over Temperature: This code means the ballast has shut itself off due to

overheating (>140° F).

5 Flash = Over Voltage: This code means the power from the outlet to your ballast

has exceeded the maximum allowed voltage.

6 Flash = Lamp Fault: Incorrect/non compatible lamp will not work with ballast.

The Sun System 1 Etelligent digital lighting controller enables the grower to control up to 400

xtures. Features an industry rst, ability to control any Sun System Etelligent compatible xture

or ballast with the same controller, operating on separate channels. This two channel controller

allows daisy-chaining up to 200 xtures per zone. Enabling complete control of your growing

environment with timed on/off switching, sunrise/sunset, accurate temperature readings with

dual thermal probes and thermal-threshold auto dim-shutdown for additional protection.

Sun System 1 Etelligent Controller Kit #902245 allows wired control of the on/off dimming

capabilities. Complete kit includes: 1 Etelligent Controller, 1 universal power adapter 5 ft/1.5 m cable,

2 each 16 ft/5 m signal wires with ferrites for connection from controller to ballast and 2 each 16 ft/5

m temperature probes.

4

CONTROL UP TO 400 SUN SYSTEM DOUBLE-ENDED

COMMERCIAL FIXTURES OR OTHER COMPATIBLE

MODELS WITH ONE ETELLIGENT CONTROLLER!

ZONE A (up to 200 xtures) ZONE B (up to 200 xtures)

 This product contains delicate electronic components. This means that if it is placed near an object that transmits

radio signals, it could cause interference. This could be, for example, mobile telephones, walkie talkies, CB radios,

remote controls and microwaves. If interference occurs, move such objects away from the appliance.

Sun System

Pro Sun 1000 W DE Commercial Fixture.

Compliant with FCC Part 18 Class A (governs commercial use) and FCC Part 18 Class B (governs residential

use) as tested by an independent US testing lab in a true as used conguration. In our case, Northwest EMC

or ElectroMagnetic Investigations, Hillsboro OR.

This installation guide does not supersede national, state, or local regulations for electrical installations.

TROUBLESHOOTING… IF YOUR FIXTURE DOES NOT WORK:

1. CHECK YOUR ELECTRICAL SOURCE: Make sure the unit is plugged in properly and that the

breaker is not tripped or fuse blown.

2. CHECK THE LAMP COLOR: Make sure the lamp is fully seated in the socket.

POSSIBLE CAUSES CORRECTIVE MAINTENANCE

LAMP LOOSE

IN SOCKETS

Make sure that the lamp is fully inserted into the socket and that the

socket is in the closed position.

INCORRECT

VOLTAGE

Make sure you are using the correct input voltage with xture. If

using incorrect voltage, disconnect the xture from the power source

immediately.

DEFECTIVE OR

IMPROPER WIRING

Examine wiring to ensure it agrees with wiring diagrams on xture label.

Check connections to see that they are secure. If wiring a 240 volt xture,

DO NOT use a neutral. The correct wiring is two hot wires and a ground.

POOR ELECTRICAL

CONNECTIONS

Check wiring and lamp contact with socket. Make sure the lamp cord is

rmly seated in output receptacle.

INCORRECT

LAMP Verify that you are using a 1000 W double-ended lamp.

LAMP

DAMAGE

Investigate possibility of outer bulb damage.

Look for broken tubes or loose metal parts. Replace lamp.

TROUBLESHOOTING GUIDE

Follow the troubleshooting tips below. If troubleshooting techniques fail, bring ballast back to

your place of purchase to request warranty service.

5

FCC compliance This device complies with Part 18 of the FCC Rules.

Advisory statement

This product may cause interference to radio equipment

and should not be installed near maritime safety

communications equipment or other critical navigation

or communication equipment operating between

0.45-30 MHz.

The interference potential

of the device or system

The interference potential of the device or system is the

operating frequency; 110 kHz.

Maintenance of the system Unplug the unit, wait 30 seconds, and plug the unit

back in.

Simple measures that can be taken

by the user to correct interference Move the unit away from any radio device.

WARRANTY SERVICE:

Please read warranty information rst. If after troubleshooting problems the light will still

not work, you should return the light to the dealer where you purchased it. They will be able

to further evaluate the light and test its various components and quite possibly will be able

to identify and/or x any problems. Often the problem is as simple as a defective lamp. If

the dealer is unable to x the light, they will return it to us for factory repair. Many dealers

have loaner xtures that you may check out until yours is returned (usually not more than

7-10 days). Please complete the “Dealer Search” on our website to locate the dealer nearest

you. To located dealers within the United States: www.HawthorneGC.com. To located dealers

within Canada: www.HawthorneGC.ca. If there are no dealers in your area, you may contact

us directly for technical support. If we cannot help you resolve the problem over the phone,

we will issue you a RMA # (return merchandise authorization) authorizing you to return the

system to us for factory reconditioning (if the unit is under warranty). You will need to provide

an email address or fax number so that the Authorization Form may be sent to you. You will

need to include this Authorization Form in the packaging when returning your Sun System

Pro Sun unit. Also please write the RMA # on the outside of the box. Please package the light

carefully in its original packaging. If it is damaged in shipment we will not be responsible.

Once we receive the light, we will repair it within 48 hours (business) and return it to you

via UPS Ground. If the unit cannot be repaired, a replacement will be sent. If there are no

replacements available, a comparable unit will be sent back.

IMPORTANT:

PROOF OF PURCHASE REQUIRED FOR RETURNS

SUN SYSTEM PRO SUN 1000 W DE COMMERCIAL FIXTURE:

3 Year Warranty Returning Units: Please contact your retail store for returns.

WARRANTY INFORMATION: The Hawthorne Gardening Company warrants to the

original purchaser of this product against defects in material and workmanship under normal

use for 3 year on SUN SYSTEM PRO SUN 1000 W DE COMMERCIAL FIXTURE. During the

warranty period, The Hawthorne Gardening Company will, at our option, and without charge,

repair or replace this product if the unit or any of its components fail or malfunction. This

warranty is expressly in lieu of all other warranties, expressed or implied, including the

warranties of merchantability and tness for use and of all other obligations or liabilities

on the part of the seller. This warranty shall not apply to this product or any part thereof

which has been damaged by accident, abuse, misuse, modication, negligence, alteration

or misapplication. The Hawthorne Gardening Company makes no warranty whatsoever in

respect to accessories or parts not supplied by The Hawthorne Gardening Company. This

warranty shall apply only to the United States, including Alaska, Hawaii, territories of the

United States and Canada.

NOTE: The Hawthorne Gardening Company is a manufacturer of supplementary lighting

systems. All sales offerings to the public are done through a nationwide group of dealers. No

sales offerings will be made directly to the general public.

6

NOTES

_________________________________________________________________________

7

NOTES

_________________________________________________________________________

Manufactured for Hawthorne Hydroponics LCC,

a subsidiary of The Hawthorne Gardening Company

3204 NW 38th Circle, Vancouver, WA 98660

|

HawthorneGC.com

|

HawthorneGC.ca

080318LM

906292 Instructions

906293 Instructions 906293_Instructions 906293_Instructions product s sunlightsupply 3:

906306 Instructions 906306_Instructions 906306_Instructions product s sunlightsupply 3:

906308 Instructions 906308_Instructions 906308_Instructions product s sunlightsupply 3:

Navigation menu

Versions of this User Manual:

Views

Navigation