ATD31166_rev_0418 ATD31166 Rev 0418
User Manual: Pdf ATD31166_rev_0418
Open the PDF directly: View PDF 
.
Page Count: 7
| Download | |
| Open PDF In Browser | View PDF |
ATD-31166 3/8” x 50’ Retractable Air Hose Reel Owner’s Manual Features Specifications x Heavy-gauge, all-steel reel assembly x8-position ratchet mechanism locks reel at desired hose length x 5-position adjustable roller outlet arm and slotted mounting bolt holes allow easy reel mounting to ceiling, wall, floors, workbenches, vehicles, etc. x Maximum Pressure: 300 psi x Hose: 3/8" x 50 ft. x Max Air Flow: 25 CFM x Inlet Air Connection 1/4" NPT(F) swivel x Hose Connections 1/4" NPT(M) Made in China to ATD Tools, Inc. Specifications Visit us on the web at www.atdtools.com ATD31166_rev_0418 Read and understand entire manual before assembling or using hose reel Failure to follow instructions or warnings could result in personal injury and/or property damage. Safety Rules DO NOT EXCEED 300 PSI incoming air pressure (from compressor) Wear impact-resistant eye protection that meets ANSI Spec. Z87.1 in work area at all times. Do not release hose when rewinding. Hold hose end and allow hose to rewind slowly. Never allow children to use hose reel. Keep children clear of work area at all times. Warning Do not over tighten reel. This may permanently damage the spring in the winding mechanism. Ideally, the reel should be adjusted to wind up only as far as the desired height needed to reach the hose stop. Exercise care when handling the hose reel during normal operation. This hose reel has a rotating spool powered by springs under tension. Mounting hardware and fasteners should be installed to maintain tightness under vibration and checked periodically to ensure tightness. Overhead installation mountings should be such that the reel is not supported by bolts in tension. A safety chain or cable is strongly recommended to minimize damage and/or possible injury in the event of mounting failure. Installing Hose Reel Note: Due to the infinite ways one would mount this reel, the mounting hardware is not included and must be purchased separately. Decide first where reel will be mounted before purchasing hardware. Different mounting positions require different types of hardware. Reel can be mounted on the floor, ceiling, or wall. When choosing a location, remember that you can only mount reel to a load-bearing structural member capable of supporting combined weight of reel, hose, and forces caused by pulling or maneuvering hose. Generally, mounting reel near your air compressor is best since you can connect the two with a shorter, less expensive length of hose. Also, air compressor controls will be nearby for convenient adjusting. OUTLET HOSE HOSE STOP GUIDE ARM MOUNTING BASE 1 Once you have located a mounting spot, consult the “Typical Mounting Positions” chart below and choose the diagram that most closely matches your mounting position. If necessary, adjust guide arm position to match diagram. Typical Mounting Positions WALL FLOOR CEILING ADJUSTING THE GUIDE ARM x Pull out 3 feet of hose and allow reel to lock in position. x Remove the four bolts connecting guide arm to mounting base. x Rotate guide arm in 90° increments to desired position total number of positions is five (5). x Replace four bolts and tighten. Continue by choosing proper mounting hardware. See illustration on following page for Dimensions. Use washers on mounting bolts to help bear weight of reel (Bolts and Washers are not included). After reel is secured in position, attach air hose coming from compressor. Wrap threads of male connector on incoming air hose with Teflon tape (included) or thread sealant and connect to air inlet valve on side of hose reel. Connect other end of incoming air hose to air compressor. Apply Teflon tape to threads on hose before attaching air tools. 2 8.464” (21.5 cm) 20.07” (51 cm) 22.04” (56 cm) 1-3/16” 4-23/32” 3” 4-15/16” 1/2” 5-29/32” 3 ADJUSTING THE HOSE BALL STOP The hose ball stop determines the length of hose that remains outside of reel. To adjust, pull hose out past desired position of hose ball stop and latch reel. Loosen both screws and move ball stop to proper position. Tighten screws. Operating Hose Reel 1. Slowly pull hose from reel to desired length. A ratcheting mechanism inside reel makes a short series of clicking sounds every half revolution of reel. 2. To lock reel in position, listen for clicking sounds as hose is slowly pulled from reel. When reel clicks, stop pulling hose. Decrease tension on hose and reel should lock in position. 3. To retract hose onto reel, slowly pull out hose until series of clicking sounds stops (1/8 revolution). DO NOT LET GO OF HOSE! 4. Allow hose to retract slowly until hose ball stop rests against the hose guide. 5. Periodically check the hose for excessive wear and hose connections for air leaks. ADJUSTING RECOIL TENSION 1. Disconnect incoming air supply. 2. Pull out about 2 feet of hose and latch the reel. 3. Remove hose ball stop 4. While firmly holding onto edge of reel drum, unlatch reel and carefully allow drum to slowly rewind, drawing hose end back through guide arm roller assembly and onto reel. Latch reel in position. 5. To Increase Tension: Unlatch reel and turn clockwise (as viewed from air inlet side). To Decrease Tension: Unlatch and allow reel to rotate slowly counterclockwise (as viewed from air inlet side). 6. Once desired spring tension is reached, latch reel in position. Feed hose end through roller assembly in guide arm and reattach hose ball stop. 7. Connect incoming air supply. REPLACING HOSE 1. Secure and stabilize reel. In most cases, hose can be replaced with reel still mounted. 2. Disconnect incoming air supply. 3. Pull out entire length of hose and lock reel. Make sure reel is securely locked in place. 4. Unscrew hose clamps that secure hose to drum. Disconnect inlet-end of hose from air inlet valve. 5. Pull inlet-end of hose through slot in drum and guide rollers, removing old hose completely. 6. Remove spring hose guard, hose clamp and hose ball stop from old hose. Fit these parts on new hose in identical positions. 7. Feed inlet-end of hose through guide rollers and slot in drum. 8. Apply Teflon sealant tape or thread sealant to hose connector and connect to air inlet valve. 9. Attach hose clamp to drum. Rewind hose onto reel using normal operation. 4 ATD-31166 32 5 36 22 4 21 24 13 17 9 3 24 34 32 29 17 26 14 15 27 2 31 35 30 16 8 17 11 10 37 12 7 7 38 39 ITEM# ORDERING PART# 1 PRT31166-01 2 PRT31166-02 3 PRT31166-03 4 PRT31166-04 5 PRT31166-05 6 PRT31166-06 7 PRT31166-07 8 PRT31166-08 9 PRT31166-09 10 PRT31166-11-29 11 PRT31166-11-29 12 PRT31166-11-29 13 PRT31166-13 14 PRT31166-14 15 PRT31166-15 16 PRT31166-16 17 PRT31166-17 18 PRT31166-18 6 17 1 28 20 25 25 18 PART DESCRIPTION SPRING CANISTER DRUM (AIR INLETSIDE) DRUM (MOUNTING BRACKET SIDE) MOUNTING BRACKET GUIDE ARM AIR INLET VALVE BODY & SWIVEL COLLAR WITH O-RINGS 3/8ͳHOSE SPRING HOSE GUARD HUB BEARING ASSEMBLY LOCKING CAM, SPRING, LOCKING GEAR KIT* LOCKING CAM, SPRING, LOCKING GEAR KIT* LOCKING CAM, SPRING, LOCKING GEAR KIT* AXLE LOCK WASHER NUT BOLT LOCK NUT CLAMP ITEM# ORDERING PART# 20 PRT31166-20 21 PRT31166-21 22 PRT31166-22 24 PRT31166-24 25 PRT31166-25 26 PRT31166-26 27 PRT31166-27 28 PRT31166-28 29 PRT31166-11-29 30 PRT31166-30 31 PRT31166-31 32 PRT31166-32 34 PRT31166-34 35 PRT31166-35 36 PRT31166-36 37 PRT31166-37 38 PRT31166-38 39 PRT31166-39 *PRT31166-11-29 includes item numbers 10. 11, 12 & 29 5 PART DESCRIPTION BOLT WASHER NUT BOLT NUT LOCK NUT ROLLER GUIDE BRACKET ASSEMBLY HOSE STOPPER ASSEMBLY LOCKING CAM, SPRING, LOCKING GEAR KIT* SPACING WASHER RETAINING RING BOLT SET SCREW SPACING WASHER NUT SPACING WASHER PIN 3/8" LEAD HOSE WARRANTY 1 YEAR LIMITED WARRANTY THIS WARRANTY AND CONFIRMED RECEIPT(S) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES PURCHASED FROM: _______________________________________ DATE PURCHASED: ________________________________________ INVOICE/RECEIPT NUMBER: _________________________________________ Your ATD-31166 is warranted for a period of 12 months from the original purchase date. For a period of one (1) year from your purchase date, ATD Tools Inc. will repair or replace (at its option) without charge, your ATD product if it was purchased new and the product has failed due to a defect in material or workmanship which you experienced during normal use of the product. This limited warranty is your exclusive remedy. To access the benefits of this warranty, contact your supplier, or point of sale directly. You may be advised to return the product under warranty, freight prepaid, to your supplier for warranty determination. If this ATD product is altered, abused, misused, modified, or undergoes service by an unauthorized technician, your warranty will be void. We are not responsible for damage to ornamental designs you place on this ATD product and such ornamentation should not cover any warnings or instructions or they may void the warranty. This warranty does not cover scratches, superficial dents, and other abrasions to the paint finish that occur under normal use. It also does not cover normal wear items such as but not limited to brushes, batteries, drill bits, drill chucks, pads or blades. Subject to the law in your state: (1) Your sole and exclusive remedy is repair or replacement of the defective product as described above. (2) ATD is not liable for any incidental damages, including but not limited to, lost profits and unforeseeable consequences. (3) The repair and replacement of this product under the express limited warranty described above is your exclusive remedy and is provided in lieu of all other warranties, express or implied. All other warranties, including implied warranties and warranties of merchantability or fitness for a particular purpose are disclaimed and, if disclaimer is prohibited, these warranties are limited to one year from your date of purchase of this product. Some states’ laws do not allow limited durations on certain implied warranties and some states’ laws do not allow limitations on incidental or consequential damages. You should consult the law in your state to determine how your rights may vary. [Affix receipt or invoice here for safe keeping] 6
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : jlovetto Create Date : 2018:04:10 16:02:43-05:00 Modify Date : 2018:04:10 16:02:43-05:00 XMP Toolkit : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08 Format : application/pdf Title : ATD31166_rev_0418 Creator : jlovetto Metadata Date : 2018:04:10 15:55:41-05:00 Creator Tool : Adobe Illustrator CS5.1 Thumbnail Width : 28 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 4139 bytes, use -b option to extract) Instance ID : uuid:b15cf0fe-9be1-43a8-8a63-79c41a819dae Document ID : xmp.did:12B6FA7C013DE81183F7EBD911239923 Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:11B6FA7C013DE81183F7EBD911239923 Derived From Document ID : xmp.did:11B6FA7C013DE81183F7EBD911239923 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved, saved, saved History Instance ID : xmp.iid:B5446DECB145E51184B4BC506D6491B3, xmp.iid:CF34972B8007E811AE14AED5B8044135, xmp.iid:11B6FA7C013DE81183F7EBD911239923, xmp.iid:12B6FA7C013DE81183F7EBD911239923 History When : 2015:08:18 09:29:42-05:00, 2018:02:01 14:20:31-06:00, 2018:04:10 15:55:23-05:00, 2018:04:10 15:55:36-05:00 History Software Agent : Adobe Illustrator CS5.1, Adobe Illustrator CS5.1, Adobe Illustrator CS5.1, Adobe Illustrator CS5.1 History Changed : /, /, /, / Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : True N Pages : 1 Max Page Size W : 8.500000 Max Page Size H : 11.000000 Max Page Size Unit : Inches Font Name : Calibri-Bold, Calibri, ArialMT, Arial-BoldItalicMT, Arial-BoldMT, MyriadPro-Bold, MyriadPro-Regular, SimSun, SymbolMT Font Family : Calibri, Calibri, Arial, Arial, Arial, Myriad Pro, Myriad Pro, 宋体, Symbol Font Face : Bold, Regular, Regular, Bold Italic, Bold, Bold, Regular, Regular, Regular Font Type : Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, TrueType, Open Type Font Version : Version 5.73, Version 5.73, Version 5.20, Version 5.20, Version 5.20, Version 2.062;PS 2.000;hotconv 1.0.57;makeotf.lib2.0.21895, Version 2.062;PS 2.000;hotconv 1.0.57;makeotf.lib2.0.21895, Version 5.03, Version 5.00 Font Composite : False, False, False, False, False, False, False, False, False Font File Name : calibrib.ttf, calibri.ttf, arial.ttf, arialbi.ttf, arialbd.ttf, MyriadPro-Bold.otf, MyriadPro-Regular.otf, simsun.ttc, symbol.ttf Plate Names : Cyan, Magenta, Yellow, Black, PANTONE 286 C, PANTONE 505 C, PANTONE 187 C Swatch Group Name : Default Swatch Group, Grays, Brights Swatch Group Type : 0, 1, 1 Swatch Colorant Swatch Name : White, Black, CMYK Red, CMYK Yellow, CMYK Green, CMYK Cyan, CMYK Blue, CMYK Magenta, C=15 M=100 Y=90 K=10, C=0 M=90 Y=85 K=0, C=0 M=80 Y=95 K=0, C=0 M=50 Y=100 K=0, C=0 M=35 Y=85 K=0, C=5 M=0 Y=90 K=0, C=20 M=0 Y=100 K=0, C=50 M=0 Y=100 K=0, C=75 M=0 Y=100 K=0, C=85 M=10 Y=100 K=10, C=90 M=30 Y=95 K=30, C=75 M=0 Y=75 K=0, C=80 M=10 Y=45 K=0, C=70 M=15 Y=0 K=0, C=85 M=50 Y=0 K=0, C=100 M=95 Y=5 K=0, C=100 M=100 Y=25 K=25, C=75 M=100 Y=0 K=0, C=50 M=100 Y=0 K=0, C=35 M=100 Y=35 K=10, C=10 M=100 Y=50 K=0, C=0 M=95 Y=20 K=0, C=25 M=25 Y=40 K=0, C=40 M=45 Y=50 K=5, C=50 M=50 Y=60 K=25, C=55 M=60 Y=65 K=40, C=25 M=40 Y=65 K=0, C=30 M=50 Y=75 K=10, C=35 M=60 Y=80 K=25, C=40 M=65 Y=90 K=35, C=40 M=70 Y=100 K=50, C=50 M=70 Y=80 K=70, PANTONE 286 C, PANTONE 187 C, PANTONE 505 C, C=0 M=0 Y=0 K=100, C=0 M=0 Y=0 K=90, C=0 M=0 Y=0 K=80, C=0 M=0 Y=0 K=70, C=0 M=0 Y=0 K=60, C=0 M=0 Y=0 K=50, C=0 M=0 Y=0 K=40, C=0 M=0 Y=0 K=30, C=0 M=0 Y=0 K=20, C=0 M=0 Y=0 K=10, C=0 M=0 Y=0 K=5, C=0 M=100 Y=100 K=0, C=0 M=75 Y=100 K=0, C=0 M=10 Y=95 K=0, C=85 M=10 Y=100 K=0, C=100 M=90 Y=0 K=0, C=60 M=90 Y=0 K=0 Swatch Colorant Mode : CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK Swatch Colorant Type : PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, SPOT, SPOT, SPOT, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS Swatch Colorant Cyan : 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 14.999998, 0.000000, 0.000000, 0.000000, 0.000000, 5.000001, 19.999999, 50.000000, 75.000000, 84.999996, 90.000004, 75.000000, 80.000001, 69.999999, 84.999996, 100.000000, 100.000000, 75.000000, 50.000000, 35.000002, 10.000002, 0.000000, 25.000000, 39.999998, 50.000000, 55.000001, 25.000000, 30.000001, 35.000002, 39.999998, 39.999998, 50.000000, 100.000000, 0.000000, 50.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 84.999996, 100.000000, 60.000002 Swatch Colorant Magenta : 0.000000, 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 90.000004, 80.000001, 50.000000, 35.000002, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 30.000001, 0.000000, 10.000002, 14.999998, 50.000000, 94.999999, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 94.999999, 25.000000, 44.999999, 50.000000, 60.000002, 39.999998, 50.000000, 60.000002, 64.999998, 69.999999, 69.999999, 65.999997, 100.000000, 100.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 75.000000, 10.000002, 10.000002, 90.000004, 90.000004 Swatch Colorant Yellow : 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 0.000000, 0.000000, 90.000004, 84.999996, 94.999999, 100.000000, 84.999996, 90.000004, 100.000000, 100.000000, 100.000000, 100.000000, 94.999999, 75.000000, 44.999999, 0.000000, 0.000000, 5.000001, 25.000000, 0.000000, 0.000000, 35.000002, 50.000000, 19.999999, 39.999998, 50.000000, 60.000002, 64.999998, 64.999998, 75.000000, 80.000001, 90.000004, 100.000000, 80.000001, 0.000000, 78.999996, 100.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 94.999999, 100.000000, 0.000000, 0.003099 Swatch Colorant Black : 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 30.000001, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 25.000000, 0.000000, 0.000000, 10.000002, 0.000000, 0.000000, 0.000000, 5.000001, 25.000000, 39.999998, 0.000000, 10.000002, 25.000000, 35.000002, 50.000000, 69.999999, 2.000000, 20.000000, 25.000000, 100.000000, 89.999402, 79.998797, 69.999701, 59.999102, 50.000000, 39.999402, 29.998803, 19.999701, 9.999102, 4.998803, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.003099 Swatch Colorant Tint : 100.000000, 100.000000, 100.000000 Producer : Acrobat Distiller 11.0 (Windows) Page Count : 7EXIF Metadata provided by EXIF.tools