Aal Aln440 Spec
2016-02-24
: Pdf Aal Aln440 Spec aal_aln440_spec spec products aal
Open the PDF directly: View PDF .
Page Count: 2
Download | |
Open PDF In Browser | View PDF |
TYPE ALN440 – Towne Commons® • Hinged top for easy relamping • Four distribution patterns • Unitized one-piece lens with a one-piece memory retentive silicone g asket provides a sealed fixture as well as easy lens replacement • Powder coat finish in 13 standard colors with a polymer primer sealer • Tool-less access to the ballast module and quick disconnects for easy servicing 1. LUMINAIRE 2. LAMP/BALLAST 4. OPTIONS 5. CONTROL 4. OPTIONS 1. LUMINAIRE ARM OR POST TOP MOUNT Clear acrylic lens, coated lamp ALN 440-C Clear lens, glass refractor ALN 440-GR3 (Type 3) ALN 440-GR5 (Type 5) Clear lens, horizontal cutoff reflector ALN 440-H2 (Type 2) ALN 440-H3 (Type 3) ALN 440-H4 (Type 4) ALN 440-H5 (Type 5) TOP MOUNTED ARM OR PENDANT MOUNT Clear acrylic lens, coated lamp ALN 440D-C Clear lens, glass refractor ALN 440D-GR3 (Type 3) ALN 440D-GR5 (Type 5) Clear lens, horizontal cutoff reflector ALN 440D-H2 (Type 2) ALN 440D-H3 (Type 3) ALN 440D-H4 (Type 4) ALN 440D-H5 (Type 5) 2. LAMP/BALLAST COMPACT FLUORESCENT (120 thru 277 volt) GE F57QBX lamp. Reflector models only PL57 GE F70QBX lamp. Reflector models only PL70 METAL HALIDE (120/208/240/277) Medium base, ED-17 lamp 70MH 100MH 50MH G12 base, T-6 ceramic lamp 70MHT6 CHM (Glass chimney with polished brass holder. Reflector models only) CND (3-lamp candelabra with polished brass holder, lamps included. For decorative use only. Reflector models only) LDL (Lightly diffused lens for fixtures with a refractor or reflector) HSS-L (House side shield for use with glass refractors or clear lens only, consists of three field installed panels attached to the inside of the lens. Installing three panels blocks 180° of the lens. Not available with PL ballast options) HSS-R (House side shield for use with horizontal reflectors. Factory installed. Not for Type 5) QL (Socket for T-4 mini-cand lamp, field wired to a separate circuit. QL lamp wattage not to exceed primary lamp wattage. Reflector models only) QRS (Restrike controller and T-4 socket for quartz lamp. Configured to light following resumption of power until HID reaches full brightness. Lamp wattage not to exceed ballast wattage.) MAT (Mast arm adapter slips over a 2 3/8"/60mm O.D. pipe and is secured with 4 stainless steel set screws. For ALN440D only) PMS (Pendant mount with 48"/1220mm stem and canopy with swivel. For ALN440D only) PMC (Pendant kit includes canopy and 48"/1220mm of brass chain. For ALN440D only) PT5 (Post top adaptor for a 5"/127mm O.D. pole) 347 (120/277/347 volt for HID ballasts) PULSE START METAL HALIDE (120/208/240/277 volt ballast) Medium base, ED-17 lamp 150PSMH G12 base, T-6 ceramic lamp 150PSMHT6 HIGH PRESSURE SODIUM (120/208/240/277 volt ballast) Medium base, ED-17 lamp 50HPS 70HPS 100HPS 150HPS All ballasts are factory wired for 277 volts, unless specified. Lamps not included. 3. COLOR WH Arctic White BL Black BLT Matte Black DGN Dark Green DB Dark Bronze WDB Weathered Bronze MDB Bronze Metallic ALN440-H3-CHM 3. COLOR VBU Verde Blue CRT Corten MAL Matte Aluminum MG Medium Grey AGN Antique Green LG Light Grey RAL Premium Color CUSTOM * * Contact Factory 5. CONTROL SCP (Programmable motion control, factory default is 50%, requires pole) PCA-C (Rotatable photocell-Contemporary) SPECIFICATIONS HOUSING The fixture shall be cast A356 alloy aluminum, free of any porosity or cosmetic fillers. Castings shall be of uniform wall thickness, minimum .188" with no warping or mold shifting. The top shall hinge open by loosening two captive fasteners. The top shall seal the lamp compartment with a full surround silicone gasket. The lens shall be one-piece clear optical grade acrylic with a one-piece memory retentive silicone gasket on top and bottom. The ballast assembly shall be accessible by turning two spring loading latches, to lift out the ballast module. Quick disconnects shall be used for all electrical connections. All internal and external hardware shall be stainless steel. OPTICAL MODULE REFLECTORS: The optical assembly shall be completely sealed with a one-piece memory retentive silicone gasket to prevent dust, insect, or moisture contamination. The reflector module shall consist of segmented, specular and semi specular Alzak® panels precisely formed and positioned within the housing on a carrier plate. Reflector models shall be IES rated as a cutoff luminaire. REFRACTORS: The GR3 and GR5 shall be precision molded borosilicate glass refractors with a Type 3 or Type 5 distribution. The refractors shall be mounted to a gasketed aluminum holder with an internal pressure plate 6. MOUNTING See next page WALL MOUNT WMA1M WMA3 WMA38 WMA56 WMA1L WMA35U WMA39 WMA57 WMA2M WMA36U WMA4 WMA6 WMA2L WMA7 WMA55 WMA7 WMA8 WMA11 WMA18 WMA9D WMA12 WMA22D WMA9U WMA16 WMA22U WMA10 WMA17 POLE MOUNT TRA1M TRA1L TRA2M TRA2L TRA3 TRA4 TRA5U TRA6U TRA55 TRA56 TRA57 TRA7 TRA7-2 TRA8 TRA8-2 TRA9 TRA9-2 SLA1 SLA1-2 SLA3 SLA4 SLA4-2 SLA7 SLA7-2 SLA7(5) SLA7(5)-2 SLA8U SLA8D SLA9-2 SLA10 SLA16 SLA9 SLA16-2 SLA17 SLA17-2 SLA18 SLA18-2 SLA22D SLA22U PENDANT PM1 PM2 PM3 ARCHITECTURAL AREA LIGHTING 16555 East Gale Ave. | City of Industry | CA 91745 P 626.968.5666 | F 626.369.2695 | www.aal.net Copyright © 2012 | Rev 2.15 6. MOUNTING JOB TYPE NOTES | 1 | TYPE ALN440 – Towne Commons® DIMENSIONS Photometric Report ELECTRICAL CATALOG NUMBER: ALN 440-H3 100MH POST TOP Ballasts shall be high power factor rated for -30°C starting. The standard cast fitter slips The ballast shall be mounted to a cast holder for FILENAME: maximumALN 440-H3 100MH.IES over a 4"/100mm O.D. pole. heat dissipation. Medium base, porcelain socketsIESNA:LM-63-2002 shall WT: 42 lbs EPA: 2.16 [TEST] LRL 599-2B be pulse rated. The compact fluorescent shall have an [TESTLAB] LRL [MANUFAC] ARCHITECTURAL AREA LIGHTING electronic transformer, 120 thru 277 volt. High output [LUMCAT] ALN 440-H3 100MH fluorescent lamps shall be powered by an electronic ballast [LUMINAIRE] HEXAGONAL CAST ALUMINUM HOUSING, [MORE] SEGMENTED, SEMI-SPECULAR/HAMMERTONE and shall be rated for a minimum starting temperature [MORE] ALZAK REFLECTOR. TOP OF FIXTURE of -10°C. The electrical assembly shall be installed and [MORE] HINGES FOR RELAMPING. CORROSION [MORE] RESISTANT POLYESTER POWDER COAT FINISH. prewired in the fixture. 18"/460mm Wednesday, July 11, 2012 32" 815mm [MORE] HORIZONTAL LAMP. TYPE III REFLECTOR. [LAMPCAT] MH100/U/M RELAMPING [LAMP] ONE 100 WATT MEDIUM BASE E-17 CLEAR METAL HALIDE The top of the fixture shall hinge open for relamping by SUMMARY DATA loosening two stainless steel fasteners. ALN 440 EFFICIENCY (Total): 61.7 % MOUNTING EFFICIENCY (Down / Up): 59.7 % / 2.0 % Post top mounting: The fixture shall slip over a 4"/100mm EFFICIENCY (Street / House): 41.2 % / 20.4 % ROADWAY CLASSIFICATION: ARM MOUNT TYPE III, SHORT O.D. pole or tenon and be secured to the pole with three (or CUTOFF CLASSIFICATION: 18"/460mm DIASEMICUTOFF x 28"/710mm LUMENS/LAMP: 00 six) stainless steel set screws. WT: 40 lbs EPA:932.16 NO. OF LAMPS: 18"/460mm 1 LUMINOUS CIRCULAR Arm or wall mounting: The fixture shall be attached to the OPENING: Diameter: 1.50 (Feet) cast arm with three stainless steel bolts and a silicone INPUT WATTS: 129 gasket. CATALOG NUMBER: ALN 440-H5 100MH Photometric Report 28" 710mm FINISH FILENAME: ALN 440-H5 100MH.IES Fixture finish shall consist of a five stage pretreatment IESNA:LM-63-2002 regimen with a polymer primer sealer, oven dry off[TEST] and LRL 599-2D top coated with a thermoset super TGIC polyester[TESTLAB] powderLRL [MANUFAC] ARCHITECTURAL AREA LIGHTING [LUMCAT] ALN 440-H5 100MH coat finish. The finish shall meet the AAMA 2604-02 [LUMINAIRE] HEXAGONAL CAST ALUMINUM HOUSING, performance specification which includes p assing a 3000 [MORE] SEGMENTED, SEMI-SPECULAR/HAMMERTONE [MORE] ALZAK REFLECTOR. TOP OF FIXTURE hour salt spray test for corrosion resistance. Wednesday, July 11, 2012 ALN 440D [MORE] HINGES FOR RELAMPING. CORROSION [MORE] RESISTANT POLYESTER POWDER COAT FINISH. CERTIFICATION [MORE] HORIZONTAL LAMP. TYPE V REFLECTOR. Fixtures shall be listed with ETL for outdoor, wet location [LAMPCAT] MH100/U/M ALN440 H3 100MH WATTAGE: 129 [LAMP] ONE 100 WATT MEDIUM BASE E-17 CLEAR METAL HALIDE use, conforming to the UL 1598 and Canadian CSA 22.2 no. 250 standard. B2 U3 G2 SUMMARY DATA FORWARD LIGHT LUMEN EFFICIENCY (Total): 62.2 % WARRANTY / TERMS AND CONDITIONS OF SALE % EFFICIENCY (Down / Up): % / 2.6 3.5% 198 FL 30 o 59.6 EFFICIENCY (Street / House): 30.3 % / 31.9 % Download: o 30.3% 1727 FM 60 TYPE ROADWAY CLASSIFICATION: III, SHORT http://www.hubbelllighting.com/resources/warranty/ CUTOFF CLASSIFICATION: 30.8% FH 80 o CUTOFF 1755 LUMENS/LAMP: 9300 FVH 90 o 1 0.9% 49 NO. OF LAMPS: LUMINOUS OPENING: CIRCULAR Diameter: BACK LIGHT 1.50 (Feet) o 129 INPUT WATTS: 3.0% BL 30 BM 60 o BH 80 o BVH 90 o 17.2% 9.6% 1.5% 174 984 549 88 UPLIGHT UL 100 o UH 180 o 1.1% 2.1% 61 121 ALN440 H5 100MH LUMEN OUTPUT: 5705 ISO-ILLUMINANCE DIAGRAM (fc) EFFICACY: 44.2 Lm/W Mounting UPLIGHT 2.0% Height Multiplier DOWNLIGHT 59.4% -----------------------10 15 20 25 30 35 40 45 50 0.010.020.05 0.1 0.2 0.5 1. 4.000 1.778 1.000 0.640 0.444 0.327 0.250 0.198 0.160 + = Point of max candela 14' MOUNTING Mounting Height =HEIGHT 20 Feet. Each box represents one mounting height. WATTAGE: 129 LUMEN OUTPUT: 5751 EFFICACY: 44.6 Lm/W ISO-ILLUMINANCE DIAGRAM (fc) Reported data calculated from manufacturer's data file, based on IESNA recommended methods. B3 U3 Photometric Viewer v3.4 AAL reserves the right to change product specifications without notice. G3 FORWARD LIGHT FL 30 o 3.8% FM 60 o 23.4% FH 80 o 18.1% FVH 90 o 1.3% LUMEN 219 1349 1043 73 BACK LIGHT BL 30 o BM 60 o BH 80 o BVH 90 o 3.7% 24.4% 19.7% 1.5% 211 1404 1130 85 UPLIGHT UL 100 o 1.2% UH 180 o 2.9% 70 169 Mounting UPLIGHT 2.6% Height Multiplier DOWNLIGHT 59.3% -----------------------10 15 20 25 30 35 40 45 50 0.5 4.000 1.778 1.000 0.640 0.444 0.327 0.250 0.198 0.160 1. 0.2 0.1 0.05 0.02 0.01 + = Point of max candela 14' MOUNTING Mounting Height =HEIGHT 20 Feet. Each box represents one mounting height. IES files can be found at www.aal.net Reported data calculated from manufacturer's data file, based on IESNA recommended methods. ARCHITECTURAL AREA LIGHTING Photometric Viewer v3.4 16555 East Gale Ave. | City of Industry | CA 91745 P 626.968.5666 | F 626.369.2695 | www.aal.net Copyright © 2012 | Rev 2.15 | 2 |
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Instance ID : uuid:a3650208-3fcf-204b-bad3-d92d8216128c Original Document ID : adobe:docid:indd:7004a196-23f9-11e2-848d-eb0c099dca8f Document ID : xmp.id:01484D6627206811822A8BA6E49CA6DF Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:00484D6627206811822A8BA6E49CA6DF Derived From Document ID : xmp.did:C81541332E206811822AC279C9E0D196 Derived From Original Document ID: adobe:docid:indd:7004a196-23f9-11e2-848d-eb0c099dca8f Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2016:02:22 12:09:17-08:00 Create Date : 2016:02:22 12:09:17-08:00 Modify Date : 2016:02:22 12:09:20-08:00 Metadata Date : 2016:02:22 12:09:20-08:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 2 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools