B7210 Report(FCC Part 15B)
2016-04-12
: Pdf B7210 Report(Fcc Part 15B) B7210_Report(FCC_Part_15B) CertsReports 551069 ProductFiles
Open the PDF directly: View PDF 
.
Page Count: 25
| Download | |
| Open PDF In Browser | View PDF |
Report No.：T111221S01-D FCC 47 CFR PART 15 SUBPART B AND ANSI C63.4:2003 IC ICES-003 Issue 4 TEST REPORT For IP Cam Model : B7210 Trade Name : ZAVIO Issued for ZAVIO Inc. 2F, No.13, R&D Rd.II, Science Based Industrial Park, Hsinchu, Taiwan Issued by Compliance Certification Services Inc. Hsinchu Lab. NO. 989-1 Wen Shan Rd., Shang Shan Village, Qionglin Shiang Hsinchu County 30741, Taiwan, R.O.C TEL: +886-3-5921698 FAX: +886-3-5921108 http://www.ccsrf.com E-Mail : service@ccsrf.com Issued Date: January 03, 2012 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF or any government agencies. The test results of this report relate only to the tested sample identified in this report. Page 1 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D Revision History Rev. Issue Date Revisions Effect Page Revised By 00 01/03/2012 Initial Issue All Page 25 Cindy Pon Page 2 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D TABLE OF CONTENTS TITLE PAGE NO. 1. TEST REPORT CERTIFICATION ................................................................................4 2. EUT DESCRIPTION .....................................................................................................5 3. DESCRIPTION OF TEST MODES ...............................................................................5 4. TEST METHODOLOGY ...............................................................................................6 5. FACILITIES AND ACCREDITATION ...........................................................................6 5.1 FACILITIES ............................................................................................................6 5.2 ACCREDITATIONS................................................................................................6 5.3 MEASUREMENT UNCERTAINTY .........................................................................7 6. SETUP OF EQUIPMENT UNDER TEST......................................................................8 7. EMISSION TEST ..........................................................................................................9 7.1 RADIATED EMISSION...........................................................................................9-16 7.2 CONDUCTED EMISSION ......................................................................................17-20 APPENDIX SETUP PHOTOS ..........................................................................................21-25 Page 3 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D 1. TEST REPORT CERTIFICATION ： ZAVIO Inc. ： 2F, No.13, R&D Rd.II, Science Based Industrial Park, Applicant Address Hsinchu, Taiwan Equipment Under Test： IP Cam ： B7210 Model Trade Name Tested Date ： ZAVIO ： December 21, 2011 ~ January 02, 2012 APPLICABLE STANDARD Standard Item Test Result FCC Part 15 Subpart B, CLASS A AND Radiated Emission PASS Conducted Emission PASS ANSI C63.4:2003 IC ICES-003 Issue 4 WE HEREBY CERTIFY THAT: The above equipment has been tested by Compliance Certification Services Inc., and found compliance with the requirements set forth in the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Approved by: Reviewed by: Sb. Lu Sr. Engineer Gundam Lin Sr. Engineer Page 4 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D 2. EUT DESCRIPTION Product Name IP Cam Model Number B7210 Identify Number T111221S01 Received Date December 21, 2011 Power Rating 12Vdc Test Voltage 120Vac, 60Hz DC Power Cable Type Non-shielded cable, 1.5m (Non-detachable) Power Port × 1, Video Out Port × 1, RJ-45 Port × 1, Micro SD Port × 1, DI/DO Port × 2 I/O Port Power Adapter : No. Manufacturer 1 DVE Model No. Power Input Power Output DSA-20CA-12 120150 100-240Vac, 50/60Hz, 0.8A 12Vdc, 1.5A Remark : For more details, please refer to the User’s manual of the EUT. 3. DESCRIPTION OF TEST MODES 1. The following test modes were scanned during the preliminary test: No. Pre-Test Mode 1 Normal Operating / Power Adapter 2 Normal Operating / PoE Mode 2. After the preliminary scan, the following test mode was found to produce the highest emission level. Final Test Mode Emission Radiated Emission Conducted Emission Normal Operating / Power Adapter Normal Operating / PoE Mode Normal Operating / Power Adapter Remark : Then, the above highest emission mode of the configuration of the EUT and cable was chosen for all final test items. Page 5 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D 4. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4:2003 and FCC CFR 47 Part 15 Subpart B, IC ICES-003 Issue 4. 5. FACILITIES AND ACCREDITATION 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at NO. 989-1 Wen Shan Rd., Shang Shan Village, Qionglin Shiang Hsinchu County 30741, Taiwan, R.O.C The sites are constructed in conformance with the requirements of ANSI C63.4:2003 and CISPR 22. All receiving equipment conforms to CISPR 16-1-1, CISPR 16-1-2, CISPR 16-1-3, CISPR 16-1-4, CISPR 16-1-5. 5.2 ACCREDITATIONS Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025. Taiwan TAF The measuring facility of laboratories has been authorized or registered by the following approval agencies. Canada Japan Taiwan USA INDUSTRY CANADA VCCI BSMI FCC MRA Copies of granted accreditation certificates are available for downloading from our web site, http:///www.ccsrf.com Page 6 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D 5.3 MEASUREMENT UNCERTAINTY The following table is for the measurement uncertainty, which is calculated as per the document CISPR 16-4-2. PARAMETER UNCERTAINTY Open Area Test Site (OATS No.3) / Radiated Emission, 30 to 1000 MHz Semi Anechoic Chamber (966 Chamber_B) / Radiated Emission, 30 to 1000 MHz +/- 3.7199 +/- 3.5189 Semi Anechoic Chamber (966 Chamber_B) / Radiated Emission, 1 to 18GHz +/- 2.5164 Semi Anechoic Chamber (966 Chamber_B) / Radiated Emission, 18 to 26 GHz +/- 2.4967 Semi Anechoic Chamber (966 Chamber_B) / Radiated Emission, 26 to 40 GHz Conducted Emission (Mains Terminals), 9kHz to 30MHz +/- 2.7655 +/- 1.5923 This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Consistent with industry standard (e.g. CISPR 22: 2006, clause 11, Measurement Uncertainty) determining compliance with the limits shall be base on the results of the compliance measurement. Consequently the measure emissions being less than the maximum allowed emission result in this be a compliant test or passing test. The acceptable measurement uncertainty value without requiring revision of the compliance statement is base on conducted and radiated emissions being less than UCISPR which is 3.6dB and 5.2dB respectively. CCS values (called ULab in CISPR 16-4-2) is less than UCISPR as shown in the table above. Therefore, MU need not be considered for compliance. Page 7 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D 6. SETUP OF EQUIPMENT UNDER TEST SUPPORT EQUIPMENT No. Product Manufacturer Model No. Serial No. FCC ID 1 Notebook PC HP ProBook 4421s CNF03242PM ----- 2 LCD Monitor DELL 2407WFPb CN-0FC255-466336CP-06JS ----- 3 LCD Monitor ViewSonic VS10563-1M PQ3053205218 DoC 4 8-poer fast Ethernet PoE Switch Air Live POE-FSH804 POEF80411700328 ----- 5 Micro SD Card SanDisk 2GB ----- ----- No. Signal Cable Description 1 Non-shielded RJ45 cable, 10m × 1 2 Non-shielded Video cable, 3m × 1 SETUP DIAGRAM FOR TESTS EUT & peripherals setup diagram is shown in appendix setup photos. EUT OPERATING CONDITION All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. Normal Operating Power Adapter: 1. Setup whole system for test as shown on diagram 2. Notebook PC ping 192.168.1.149 to EUT 3. Video output to LCD MONITOR. 4. All of the functions are under run. 5. Start test. PoE Mode: 1. Remove AC power adapter from EUT. 2. RJ-45 cable linking to PoE ethernet switch. 3. Notebook PC ping 192.168.1.149 to EUT with PoE ethernet switch. 4. Video output to LCD monitor. 5. All of the functions are under run. 6. Start test. Page 8 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D 7. EMISSION TEST 7.1 RADIATED EMISSION LIMITS (1) For Frequency Below 1GHz 47 CFR Part 15 Subpart B Section 15.109 (a) (b) Class A Frequency Field Field Field Distance (MHz) Strength Strength Strength (meters) (µV/m) (µV/m) (dBµV/m) 30 - 88 90 39.1 10 100 Class B Field Strength (dBµV/m) 40.0 Distance (meters) 3 88 - 216 150 43.5 10 150 43.5 3 216 - 960 210 46.4 10 200 46.0 3 Above 960 300 49.5 10 500 54.0 3 CISPR 22 (According to 47 CFR Part 15 Subpart B Section 15.109 (g)) Frequency Distance Field Strengths (dBµV/m) (MHz) (meters) Class A Class B 30 - 230 40 30 10 230 - 1000 47 37 10 (2) For Frequency Above 1GHz (According to 47 CFR Part 15 Subpart B Section 15.109) Field Strength (dBµV/m) Distance Frequency Class A Class B (meters) (GHz) Peak Average Peak Average Above 1GHz 80 60 74 54 3 (3) Frequency Range of Radiated Measurement (For unintentional radiators) Highest frequency generated or Upper frequency of measurement used in the device Range (MHz) or on which the device operates or tunes (MHz) Below 1.705 30 1.705 – 108 1000 108 – 500 2000 500 – 1000 5000 Above 1000 5th harmonic of the highest frequency or 40GHz, whichever is lower Page 9 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D TEST EQUIPMENT Radiated Emission below 1GHz / OATS3 Name of Equipment Manufacturer Model Serial Number Calibration Due Bi-log Antenna SCHAFFER CBL6112B 2696 10/03/2012 EMI Test Receiver ROHDE & SCHWARZ ESCI 101131 01/13/2012 Serial Number Calibration Due Remark: Each piece of equipment is scheduled for calibration once a year. Radiated Emission above 1GHz / 966Chamber_B Name of Equipment Manufacture Model Spectrum Analyzer Agilent E4446A EMI Receiver ROHDE & SCHWARZ ESCS 30 826547/004 10/27/2012 Broadband Hybrid Bi-Log Antenna Sunol Sciences JB1 A100209-4 10/05/2012 Double-Ridged Waveguide Horn ETS-LINDGREN 3117 00078733 12/06/2012 Pre-Amplifier Agilent 8447D 2944A10052 07/19/2012 Pre-Amplifier Agilent 8449B 3008A01916 09/18/2012 Notch Filters Band Reject Micro-Tronics BRM05702-01 MY43360132 06/19/2012 026 N.C.R Remark: 1. Each piece of equipment is scheduled for calibration once a year. 2. N.C.R = No Calibration Request. Page 10 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D TEST SETUP The diagram below shows the test setup that is utilized to make the measurements for emission from below 1GHz. Antenna Tower 10m Bi-log Antenna EUT 1~4m EMI Test Receiver Turntable 1m 0.8m Coaxial Cable Reference ground plane The diagram below shows the test setup that is utilized to make the measurements for emission above 1GHz. Antenna Tower Horn Antenna 3m EUT 1~4m Spectrum Analyzer Turntable Coaxial Cable 0.8m 1m Pre-amp Reference ground plane Page 11 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D TEST PROCEDURE The basic test procedure was in accordance with ANSI C63.4:2003. The devices under test were placed on a rotatable table top 0.8 meter above ground. The table was rotated 360 degrees to determine the position of the highest radiation. EUT is set 3 or 10m meters from the interference receiving antenna which is mounted on the top of a variable height mast. The antenna height is varied between one meter and four meters above ground to find the maximum value of the field strength both horizontal polarization and vertical polarization of the antenna are set to make the measurement. Note： 1. The bandwidth setting on the E.M.I. meter (EMI TEST RECEIVER) is 120 KHz. The levels are Quasi-Peak value readings. The frequency spectrum from 30MHz to 1000MHz was investigated. 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1 MHz for Peak detection and frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 10 Hz for Average detection (AV) at frequency above 1GHz. Page 12 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D TEST RESULTS Below 1 GHz Product Name IP Cam Test By Tom Deng Test Model B7210 Normal Operating / Power Adapter Test Date 2011/12/27 Temp. & Humidity 17°C, 65% Test Mode OATS3 at 10Meter / Horizontal Frequency (MHz) Antenna Cable Meter Emission Margin Limits Azimuth Height Factor Loss Reading Level Limit Remark (dBµV/m) (°) (cm) (dB/m) (dB) (dBµV) (dBµV/m) (dB) 125.11 11.82 2.08 2.95 40.00 16.85 -23.15 130 400 QP 160.03 9.94 2.50 5.12 40.00 17.56 -22.44 146 150 QP 250.65 12.77 3.45 1.41 47.00 17.63 -29.37 139 150 QP 335.48 14.09 4.11 6.14 47.00 24.34 -22.66 290 250 QP 398.26 15.64 4.68 11.78 47.00 32.10 -14.90 223 200 QP 975.36 21.41 9.20 1.32 47.00 31.93 -15.07 84 200 QP OATS3 at 10Meter / Vertical Frequency (MHz) Antenna Cable Meter Emission Margin Limits Azimuth Height Factor Loss Reading Level Limit Remark (dBµV/m) (°) (cm) (dB/m) (dB) (dBµV) (dBµV/m) (dB) 32.81 15.85 0.96 10.16 40.00 26.97 -13.03 30 100 QP 125.11 11.82 2.08 8.90 40.00 22.80 -17.20 360 100 QP 160.03 9.94 2.50 12.59 40.00 25.03 -14.97 188 100 QP 398.26 15.64 4.68 12.43 47.00 32.75 -14.25 107 100 QP 875.56 20.19 8.60 2.25 47.00 31.04 -15.96 34 200 QP 975.36 21.41 9.20 1.71 47.00 32.32 -14.68 67 150 QP Remark: 1. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit. 2. Data of measurement within this frequency range shown " --- " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 3. Emission Level (dBµV/m) = Antenna Factor (dB/m) + Cable Loss (dB) + Meter Reading (dBµV) 4. Margin (dB) = Emission Level (dBuV/m) - Quasi-peak limit (dBuV/m) Page 13 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D Product Name IP Cam Test By Tom Deng Test Model B7210 Normal Operating / PoE Mode Test Date 2011/12/27 Temp. & Humidity 17°C, 65% Test Mode OATS3 at 10Meter / Horizontal Frequency (MHz) Antenna Cable Meter Emission Margin Limits Azimuth Height Factor Loss Reading Level Limit Remark (dBµV/m) (°) (cm) (dB/m) (dB) (dBµV) (dBµV/m) (dB) 75.31 6.93 1.51 7.40 40.00 15.83 -24.17 130 300 QP 125.11 11.82 2.08 8.56 40.00 22.46 -17.54 146 100 QP 151.49 10.69 2.41 15.38 40.00 28.49 -11.51 139 150 QP 398.26 15.64 4.68 19.56 47.00 39.88 -7.12 290 200 QP 485.30 17.28 5.48 2.21 47.00 24.97 -22.03 223 100 QP 534.03 18.24 5.94 1.18 47.00 25.36 -21.64 84 200 QP OATS3 at 10Meter / Vertical Frequency (MHz) Emission Margin Antenna Cable Meter Azimuth Height Limits Level Limit Factor Loss Reading Remark (°) (cm) (dBµV/m) (dBµV/m) (dB) (dB/m) (dB) (dBµV) 39.25 14.48 1.09 13.68 40.00 29.24 -10.76 236 100 QP 75.19 6.92 1.50 26.85 40.00 35.27 -4.73 160 100 QP 125.11 11.82 2.08 18.70 40.00 32.60 -7.40 32 100 QP 150.81 10.75 2.41 20.63 40.00 33.79 -6.21 68 100 QP 398.26 15.64 4.68 18.44 47.00 38.76 -8.24 65 150 QP 521.28 17.96 5.81 3.38 47.00 27.15 -19.85 73 150 QP Remark: 1. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit. 2. Data of measurement within this frequency range shown " --- " in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 3. Emission Level (dBµV/m) = Antenna Factor (dB/m) + Cable Loss (dB) + Meter Reading (dBµV) 4. Margin (dB) = Emission Level (dBuV/m) - Quasi-peak limit (dBuV/m) Page 14 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D Above 1 GHz Product Name IP Cam Test By Tom Deng Test Model B7210 Normal Operating / Power Adapter Test Date 2011/12/26 Temp. & Humidity 17°C, 61% Test Mode 966 Chamber_B at 3Meter / Horizontal Frequency (MHz) Reading- Reading- Correction Result-PK Result-AV Limit-PK Limit-AV Margin Azimuth Height Remark Factor AV PK (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) (dB) (°) (cm) (dB/m) (dBuV) (dBuV) 1070.00 49.45 --- -3.65 45.79 --- 80.00 60.00 -14.21 139.80 100.00 Peak 1175.00 48.20 --- -3.32 44.89 --- 80.00 60.00 -15.11 25.00 100.00 Peak 1600.00 45.09 --- -1.37 43.72 --- 80.00 60.00 -16.28 11.20 200.00 Peak 2645.00 43.27 --- 4.31 47.58 --- 80.00 60.00 -12.42 342.00 200.00 Peak 4205.00 40.94 --- 7.69 48.63 --- 80.00 60.00 -11.37 153.60 200.00 Peak 4835.00 40.95 --- 9.51 50.46 --- 80.00 60.00 -9.54 342.00 100.00 Peak 966 Chamber_B at 3Meter / Vertical Frequency (MHz) Reading- Reading- Correction Result-PK Result-AV Limit-PK Limit-AV Margin Azimuth Height Remark Factor AV PK (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) (dB) (°) (cm) (dB/m) (dBuV) (dBuV) 1050.00 49.88 --- -3.72 46.16 --- 80.00 60.00 -13.84 222.40 100.00 Peak 1175.00 48.07 --- -3.32 44.75 --- 80.00 60.00 -15.25 206.30 100.00 Peak 1600.00 45.01 --- -1.37 43.64 --- 80.00 60.00 -16.36 315.90 100.00 Peak 2760.00 42.78 --- 4.67 47.45 --- 80.00 60.00 -12.55 263.80 200.00 Peak 3075.00 42.65 --- 5.49 48.14 --- 80.00 60.00 -11.86 206.10 200.00 Peak 5855.00 39.30 --- 11.50 50.80 --- 80.00 60.00 -9.20 263.10 100.00 Peak Remark: 1. Average test would be performed if the peak result were greater than the average limit. 2. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 3. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 4. Result = Reading + Correction Factor Margin = Result – Limit Remark Peak = Result(PK) – Limit(AV) Remark AVG = Result(AV) – Limit(AV) Page 15 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D Product Name IP Cam Test By Tom Deng Test Model B7210 Normal Operating / PoE Mode Test Date 2011/12/26 Temp. & Humidity 17°C, 61% Test Mode 966 Chamber_B at 3Meter / Horizontal Frequency (MHz) Reading- Reading- Correction Result-PK Result-AV Limit-PK Limit-AV Margin Azimuth Height Remark Factor AV PK (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) (dB) (°) (cm) (dB/m) (dBuV) (dBuV) 1060.00 49.30 --- -3.69 45.61 --- 80.00 60.00 -14.39 146.60 200.00 Peak 1175.00 46.56 --- -3.32 43.24 --- 80.00 60.00 -16.76 263.80 100.00 Peak 1875.00 44.32 --- 1.10 45.41 --- 80.00 60.00 -14.59 351.30 100.00 Peak 2240.00 43.62 --- 3.01 46.63 --- 80.00 60.00 -13.37 91.60 100.00 Peak 2970.00 42.47 --- 5.32 47.79 --- 80.00 60.00 -12.21 54.80 200.00 Peak 4130.00 41.54 --- 7.44 48.98 --- 80.00 60.00 -11.02 224.90 100.00 Peak 5960.00 40.41 --- 11.73 52.14 --- 80.00 60.00 -7.86 31.80 Peak 200.00 966 Chamber_B at 3Meter / Vertical Frequency (MHz) Reading- Reading- Correction Result-PK Result-AV Limit-PK Limit-AV Margin Azimuth Height Remark Factor AV PK (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) (dB) (°) (cm) (dB/m) (dBuV) (dBuV) 1060.00 52.18 --- -3.69 48.49 --- 80.00 60.00 -11.51 149.10 200.00 Peak 1175.00 46.93 --- -3.32 43.61 --- 80.00 60.00 -16.39 128.40 100.00 Peak 1600.00 45.82 --- -1.37 44.45 --- 80.00 60.00 -15.55 18.20 100.00 Peak 2145.00 43.51 --- 2.70 46.21 --- 80.00 60.00 -13.79 247.70 200.00 Peak 3130.00 42.60 --- 5.55 48.16 --- 80.00 60.00 -11.84 5550.00 40.30 --- 10.86 51.15 --- 80.00 60.00 -8.85 1.30 200.00 Peak 229.40 100.00 Peak Remark: 1. Average test would be performed if the peak result were greater than the average limit. 2. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 3. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 4. Result = Reading + Correction Factor Margin = Result – Limit Remark Peak = Result(PK) – Limit(AV) Remark AVG = Result(AV) – Limit(AV) Page 16 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D 7.2 CONDUCTED EMISSION LIMITS Voltage Limits (dBµV) Frequency Range (MHz) Class A Class B Quasi-peak Average Quasi-peak Average 0.15 - 0.50 79 66 66 - 56* 56 - 46* 0.50 - 5.00 73 60 56 46 5.00 - 30.0 73 60 60 50 Remark: (1) The limit decreases linearly with logarithm of the frequency in the range 0.15 MHz to 0.50 MHz. (2) The lower limit shall apply at the transition frequency. (3) * Decreasing linearly with the logarithm of the frequency. TEST EQUIPMENT Name of Equipment Manufacturer Model Serial Number Calibration Due L.I.S.N SCHWARZBECK NSLK 8127 8127-465 08/09/2012 L.I.S.N SCHWARZBECK NSLK 8127 8127-473 03/14/2012 EMI Receiver ROHDE & SCHWARZ ESCS 30 835418/008 10/20/2012 Pulse Limiter ROHDE & SCHWARZ ESH3-Z2 100117 09/14/2012 Remark: Each piece of equipment is scheduled for calibration once a year. TEST SETUP Page 17 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D Powerline of Peripherals 120VAC / 60Hz Powerline of EUT L.I.S.N. L.I.S.N. 120VAC / 60Hz EUT & Peripherals 120VAC / 60Hz Isolate Transformer EMI Test Receiver TEST PROCEDURE The basic test procedure was in accordance with ANSI C63.4:2003. The test procedure is performed in a 4m × 3m × 2.4m (L×W×H) shielded room. The EUT along with its peripherals were placed on a 1.0m (W) × 1.5m (L) and 0.8m in height wooden table and the EUT was adjusted to maintain a 0.4 meter space from a vertical reference plane. The EUT was connected to power mains through a line impedance stabilization network (LISN) which provides 50 ohm coupling impedance for measuring instrument and the chassis ground was bounded to the horizontal ground plane of shielded room. All peripherals were connected to the second LISN and the chassis ground also bounded to the horizontal ground plane of shielded room. The EUT was located so that the distance between the boundary of the EUT and the closest surface of the LISN is 0.8 m. Where a mains flexible cord was provided by the manufacturer shall be 1 m long, or if in excess of 1 m, the excess cable was folded back and forth as far as possible so as to form a bundle not exceeding 0.4 m in length. Page 18 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D TEST RESULTS Product Name IP Cam Test By Tom Deng Test Model B7210 Normal Operating / Power Adapter Test Date 2011/12/12 Temp. & Humidity 24°C, 65% Test Mode LINE Remark: 1. Correction Factor = Insertion loss + Cable loss 2. Emission level = Reading Value + Correction factor 3. Margin value = Emission level – Limit value Page 19 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D Product Name IP Cam Test By Tom Deng Test Model B7210 Normal Operating / Power Adapter Test Date 2011/12/12 Temp. & Humidity 24°C, 65% Test Mode NEUTRAL Remark: 1. Correction Factor = Insertion loss + Cable loss 2. Emission level = Reading Value + Correction factor 3. Margin value = Emission level – Limit value Page 20 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D APPENDIX SETUP PHOTOS RADIATED EMISSION SETUP Below 1 GHz Power Adapter Page 21 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D PoE Mode Page 22 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D Above 1 GHz Power Adapter Page 23 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D PoE Mode Page 24 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Report No.：T111221S01-D CONDUCTED EMISSION SETUP Page 25 / 25 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Page Count : 25 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:27aba77f-8766-42ff-90af-92c3ba4f14a2 Producer : Acrobat Distiller 6.0.1 (Windows) Modify Date : 2012:01:10 14:37:58+08:00 Create Date : 2012:01:10 14:33:56+08:00 Metadata Date : 2012:01:10 14:37:58+08:00 Document ID : uuid:b3d5fdd1-6096-4699-a5c0-6b89c0827b2d Format : application/pdf Title : untitledEXIF Metadata provided by EXIF.tools