BeamSafe II Perimeter Access Guarding Sensor Datasheet Beam Safe En 201507 F242I E 01

2016-05-24

: Pdf Beamsafe Ii Datasheet En 201507 F242I-E-01 BeamSafe II_datasheet_en_201507_F242I-E-01 Omron

Open the PDF directly: View PDF PDF.
Page Count: 7

C1
OMRON SCIENTIFIC TECHNOLOGIES, INC.
USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 www.sti.com
C
Perimeter Access Guarding
BeamSafe® II
Description
The BeamSafe II is a
long-range single-beam safety
control designed for perimeter
and access guarding. “Diverse
redundant” microprocessor
design provides safe, control
reliable operation.
A BeamSafe II system
consists of one transmitter
and one receiver. No intercon-
necting cables or separate
control enclosure are required.
Mounted on the receiver, four
separate visible indicators
provide instant information on
system clear, blocked or inter-
locked status as well as signal
strength. Additional diagnostic
indicators on the receiver
provide codes to assist with
troubleshooting. Output options
include redundant solid-state
or force-guided relays located
in the receiver.
Immunity to weld flash and
ambient light are enhanced
by coding the infrared beam.
This feature also eliminates
interference from other Beam-
Safe II units installed in close
proximity. A tight beam angle
reduces problems associated
with reflective surfaces. The
Beamsafe II’s built-in lens
heater is effective in environ-
ments where condensation
may form on the transmitter or
receiver lens.
C US
Long-Range, Single-Beam Safety Control
• 60m(200ft.)range
• Fourpossibletransmitcodeseliminatecrosstalkfrommultipleunitsinthesamearea
• Signalstrengthindicatorandintegral“GunSight”alloweasyinstallation
• Nointerconnectingcablesrequired,whichspeedslong-rangeinstallations
• Adjustablemountingbracketsalloweasyalignment
• Threemodelsavailable:
– Relayoutputwith24VDCpowerinput
– Relayoutputwith85to250VACpowerinput
– Solid-stateoutputwith24VDCpowerinput
• Switch-selectedAutomaticStartorStart/RestartInterlockoperation
• Lensheater
• DesignedinaccordancewithIEC61496,EN954-1and
ANSIB11.19-2003
Rev.8.12
BS2
Shown here
with optional
quick-disconnect
cable kit.
FileNo.LR90200
Specifications
Performance
ProtectedHeight: Single Beam
OperatingRange: 0.3to60m(1to200ft.)
BeamDiameter: 31mm(1.2in.)
MaximumResponseTime:
<0.035secondsforallmodels
DCModelsInputPower: 24V±10%(negativeground)
Receiver/RelayOutput:0.45AMax
Receiver/SSOutput:0.80AMax
Transmitter:0.17AMax
ACModelsInputPower:100
to230VAC±10%,50/60Hz;
Receiver115VAC:16VA
Receiver230VAC:25VA
Transmitter115VAC:10.5VA
Transmitter230VAC:20VA
EffectiveApertureAngle: 2.5°maximumhalfangle
FrequencySelection: 4non-interferingcodes,allmodels
Diagnostics: Built-in diagnostic indicators
Output: RelayOutputVersion:Tworelayswithforce-guidedcontacts,NOrated4A
at115VAC,200Wswitchedpower(2.0kVA).DCLoadsarelimitedto100V
maximum.Estimatedmechanicallifeis50,000,000operations.Electricallifeis
typically1,000,000operationsat200VA.
AuxiliaryMonitoringRelay:400VAC/DCmaximum,0.1A;totalpower180mW
maximum.
Solid-StateOutputVersion:Twosafetysolid-staterelayoutputs.Eachoutput
sources(PNP)upto0.25Aat24VDC.
Construction: Polyesterpowder-paintedaluminumbody.Anodizedaluminumend-caps.
Operating Temperature: 0to55°C(32to131°F)
Protection Category: IP65;NEMA4
Agencies: DesignedinaccordancewithIEC61496,type4andUL/CSArequirements.
Specicationsaresubjecttochangewithoutnotice.
OMRON SCIENTIFIC TECHNOLOGIES, INC.
USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 www.sti.com
C2
C
Applications (mm/in.)
BeamSafe® II Perimeter Access Guarding
Transmitter
Transmitter
Receiver
Receiver
Floor
36 in
900 mm
16 in
400 mm
1 to 176 ft
0.3 to 53 m
Long-Range
Perimeter Guarding
Twotransmitter/receiverpairsusingtwo
mirrors and Omron STI mounting stands to
direct the beam around a corner.
Double Bounce
This configuration guards access to
hazardousworkcells.Onetransmitterand
receivercombinedwithtwoOmronSTI4
in. mirrors and mounting brackets.
Transmitter
Receiver
36 in
900 mm
16 in
400 mm
1 to 75 ft
0.3 to 23
Floor
45° Mirror
45° Mirror
Transmitter
Receiver
Floor
36 in
900 mm
16 in
400 mm
1 to 59 ft
0.3 to 18 m
Perimeter Guarding
Shown here with one transmitter and
receiver. Mirrors are used to form two
beams and also turn corners.
Dimensions (mm/in.)
BeamSafeII
R
BeamSafeII Receiver
F1
F2
R
A
REF.
B
C
SLOTS FOR
T-NUTS
MOUNTING HOLES (4) FOR
ALTERNATE REAR MOUNTING
ALTERNATE REAR
CABLE ENTRY
25.4
1.00
BACK/REAR VIEW SIDE VIEW
FRONT VIEW
77.9
3.07
74.3
2.93
60
2.36
108
4.25 158.8
6.25 REF.
168.7
6.64
24.4
0.96
50.8
2.00
32.4
1.28
R27.3
1.075
TOP VIEW
35°13.0
0.55(X2)
MOUNTING BRACKET
SURFACE MTG "FOOTPRINT" DIMENSIONS
35.1
1.38
6.9
0.27DIA.
3.9
0.27(X3) C
LBOTTOM VIEW
55.9
2.20
mm
IN
Dimensions: ±
0.25
±
0.01
ADJUSTABLE
MOUNTING
BRACKET
239.6
9.44
178.9
7.05
160.1
6.31
197.7
7.79
137.2
5.40
118.4
4.66
197.7
7.79
137.2
5.40
118.4
4.66
197.7
7.79
137.2
5.40
118.4
4.66
AC Transmitter
AC Receiver
DC Receiver
DC Transmitter
BeamSafe II,
Relay Output Version
Unit Length Dims ABC
BeamSafe II, Relay Output Version
C3
OMRON SCIENTIFIC TECHNOLOGIES, INC.
USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 www.sti.com
C
BeamSafe® II Perimeter Access Guarding
Earth/Ground
Output A
Output B
Auxiliary Monitor Relay
(Non Safety Output)
(N.C.)
Start
2
Two Normally Open Contacts AC Voltage Connections
BS2RAC
7
8
3
2
1
6
5
11
12
1
2
MPCE 1MPCE 2
To Machine Control Stop Circuit
No external voltage is
to be applied to
terminals 1 & 2.
Damage to unit will occur.
2
1` WARNING: Arc suppression devices
should only be installed across the
coils of the machine control relays.
Never install Arc Suppression
devices directly across the control
output contacts of the BeamSafe.
An arc suppression device installed
across the contacts may fail with a
short circuit and will result in an
unsafe condition.
These relay contacts must be force-
guided contacts.
J6
J7
3User supplied over current
protection, 4A max.
Arc Suppressor
MPCE 2
1`
Arc Suppressor
MPCE 1
1`
3
3
100 to 230 VAC
BeamSafeII Receiver
BeamSafeII
R
FRONT VIEW
BOTTOM VIEW
35°
MOUNTING HOLES (4) FOR
ALTERNATE REAR MOUNTING
191
7.52
111.8
4.40 93.0
3.66
50.8
2.00
55.2
2.17
88.9
3.50 139.7
5.50
25.4
1.00
20.5
0.81
50.8
2.00
35.1
1.38
47.6
1.875
R27.3
1.075
32.4
1.275
Ø6.9
0.27
REF.
ALTERNATE REAR
CABLE ENTRY
SIDE VIEW
168
6.62 REF.
BACK/REAR VIEW
TOP VIEW
ADJUSTABLE MOUNTING BRACKET
SLOTS FOR
T-NUTS
13.0
0.55(X2)
6.9
0.27(X3)
MOUNTING BRACKET
SURFACE MTG "FOOTPRINT" DIMENSIONS
C
L
mm
IN
Dimensions: ± 0.25
± 0.01
BeamSafe II,
Solid-State Output Version, Tranmitter and Receiver
This drawing is available in
CAD format at www.sti.com
Dimensions (continued) (mm/in.)
Wiring
OMRON SCIENTIFIC TECHNOLOGIES, INC.
USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 www.sti.com
C4
C
BeamSafe® II Perimeter Access Guarding
Wiring (continued)
Earth/Ground
Output A
Output B
Start (N.C.)
Signal Return
1
Arc Suppressor
MPCE 2
Arc Suppressor
MPCE 1
1
Two Normally Open Contacts DC Voltage Connections (Solid-State Output Model)
6
7
3
1
4
5
MPCE 1
2
MPCE 2
To Machine Control Stop Circuit
24 VDC
+24 -24
No external voltage is
to be applied to
terminals 4 & 5;
Damage to unit will occur.
3
2
1`
WARNING: Arc suppression devices
should only be installed across the
coils of the machine control relays.
Never install Arc Suppression
devices directly across the control
output contacts of the BeamSafe.
An arc suppression device installed
accros the contacts may fail with a
short circuit and will result in an
unsafe condition.
These relay contacts must be force
guided contacts.
Sourcing
If load is less than 50 mA a resistor
must be installed across the load.
J5
2
BS2RC24
3
3
C5
OMRON SCIENTIFIC TECHNOLOGIES, INC.
USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 www.sti.com
C
BeamSafe® II Perimeter Access Guarding
Wiring (continued) (mm/in.)
Accessories (mm/in.)
Brackets
OR
BSMK
38.1
1.500
38.35
1.510
MOUNTING TABS
(4 PLACES)
MIR45-FG and MIR45-SS
MIRROR
STAINLESS STEEL
OR
GLASS
MIRROR
SUPPORT
BLOCK
MIRROR
STAND
PIPE
MIR45BKT
Earth/Ground
Output B
Auxiliary Monitor Relay
(Non Safety Output)
(N.C.)
Start
2
Two Normally Open Contacts 24 VDC Voltage Connections
6
3
2
1
1
2
4
5
MPCE 1MPCE 2
To Machine Control Stop Circuit
No external voltage is
to be applied to
terminals 4 & 5.
Damage to unit will occur.
2
1`
WARNING: Arc suppression devices
should only be installed across the
coils of the machine control relays.
Never install Arc Suppression
devices directly across the control
output contacts of the BeamSafe.
An arc suppression device installed
accros the contacts may fail with a
short circuit and will result in an
unsafe condition.
These relay contacts must be force-
guided contacts.
J1
J2
3
User supplied over current
protection, 4A max.
BS2R24
Output A
6
5
4
Arc Suppressor
MPCE 2
1`
Arc Suppressor
MPCE 1
1`
3
3
24 VDC
J2
Front Surface Glass or
Stainless Steel Mirror
OMRON SCIENTIFIC TECHNOLOGIES, INC.
USA Tel. 1/888/510-4357 Canada Tel. 1/866/986-6766 www.sti.com
C6
C
BeamSafe® II Perimeter Access Guarding
Accessories (mm/in.)
For information on safety light
curtain accessories, see page D74
✎
Ordering
Safety Standards and Precautions
The BeamSafe II meets applicable OSHA, ANSI and RIA
standardsandwasdesignedinaccordancewithIEC61496,DIN
EN50100andEN954-1.
Only use the BeamSafe II on machinery that stops consistently
and immediately anywhere in its cycle or stroke. Never use a
BeamSafe II on a full-revolution clutched press or machine.
The BeamSafe II is a single optical beam, not a curtain of light.
Therefore it is not designed for use as a point-of-operation device.
If one or more BeamSafe II systems do not protect all access to
thehazardousmachinearea,theunprotectedaccessmustbe
guarded by fencing, barriers or other appropriate methods.
The purchaser, installer and employer are responsible for
meeting all appropriate laws, rules and regulations relating to the
proper use, installation, operation and maintenance of this control
and the guarded machine.
Laser Alignment Tool
Target Clip
BEAMCHECK
Laser Level Unit
Laser Mounting Adaptor
BeamSafe II BeamSafe II
BS2LA
Model No. Description
BS2X24 Transmitter,24VDC
BS2XAC Transmitter,85to250VAC,50/60Hz
BS2XC24 Transmitter,24VDC,CompactSize(Thisisnot
compatiblewithQDXandQDRseriesconnectors)
BS2R24 Receiver,24VDC,RelayOutput
BS2RAC Receiver,85to250VAC,50/60Hz,RelayOutput
BS2RC24 Receiver,24VDC,CompactSize,Solid-stateOutput
(ThisisnotcompatiblewithQDXandQDRseries
connectors)
Accessories
MIR45-FG 4in.mirrorforusewithMIR45BKT-FrontSurfaceGlass
MIR45-SS 4in.mirrorforusewithMIR45BKT-StainlessSteel
MIR45BKT Bracketformountingabovemirrorsat45°anglesfor
usein“doublebounce”applications(kitmountsone
mirror)
BSMK Bracket kit. Allows mounting of one BeamSafe II
transmitter and one BeamSafe II receiver to Omron STI
mounting stands
MIRS-04 4ft.standformountingmirrorsandBeamSafeIIunits
MIRS-06 6ft.standformountingmirrorsandBeamSafeIIunits
QDR-12 12ft.,12-conductorreceivercable,withquick-
disconnect socket
QDR-20 20ft.,12-conductorreceivercable,withquick-
disconnect socket
QDR-35 35ft.,12-conductorreceivercable,withquick-
disconnect socket
QDX-12 12ft.,3-conductortransmittercable,withquick-
disconnect socket
QDX-20 20ft.,3-conductortransmittercable,withquick-
disconnect socket
QDX-100 100ft.,3-conductortransmittercable,withquick-
disconnect socket
BS2LA LaserAlignmentTool
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.
55.59.01.43.00
• 01-800-226-6766 • mela@omron.com
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • mela@omron.com
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
Authorized Distributor:
F242I-E-01 07/15
Note: Specifications are subject to change. © 2015 Omron Electronics LLC Printed in U.S.A.
Printed on recycled paper.
Automation Control Systems
• Machine Automation Controllers (MAC) • Programmable Controllers (PLC)
• Operator interfaces (HMI) • Distributed I/O • Software
Drives & Motion Controls
• Servo & AC Drives • Motion Controllers & Encoders
Temperature & Process Controllers
• Single and Multi-loop Controllers
Sensors & Vision
• Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors
• Amplified Photomicrosensors • Measurement Sensors
• Ultrasonic Sensors • Vision Sensors
Industrial Components
• RFID/Code Readers • Relays • Pushbuttons & Indicators
• Limit and Basic Switches • Timers • Counters • Metering Devices
• Power Supplies
Safety
• Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety
Controllers • Light Curtains • Safety Relays • Safety Interlock Switches
OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON EUROPE B.V. •
Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands.
•
+31 (0) 23 568 13 00
•
www.industrial.omron.eu

Navigation menu