Cimarron Led Spec Sheet

2016-04-21

: Pdf Cimarron Led Spec Sheet cimarron_led_spec_sheet spec products spaulding

Open the PDF directly: View PDF PDF.
Page Count: 4

A B C D E F G
6 3/4"
171mm
21 3/4"
552mm
16"
406mm
6 5/8"
168mm
6 5/16"
160mm
5 5/8"
143mm
6 1/8"
155mm
CIMARRON
LED
Construction:
Stylish vertically finned die-cast solid top
housing for maximum heat dissipation;
Stops collection of unsightly debris from
gathering on top of the housing
Rugged lower die-cast aluminum heat
sink accelerates thermal management
and optimizes PCB and optical perfor-
mance
• Separate optical and electrical compart-
ment for optimum component operation
• One piece die cut silicone gasket ensures
weather proof seal around each
individual LED for IP65 rating
Backlight Control (BC) option available for
85% spill light reduction, doesn’t change
fixture appearance or EPA, recommended
for Type III and Type IV distributions
• Stamped bezel provides mechanical
compression to seal the optical assembly
• Complements the Hubbell Southwest
series of outdoor fixtures
Weight - 45.0 pounds, EPA - 1.3 ft2
• Suitable for applications requiring 3G
testing prescribed by ANSI C136.31
Optics:
• Choice of 72 high brightness LED configu-
rations with individual acrylic lenses
specially designed for IES Type II, III, IV and
V distributions
Auto optics designed for front row 1A and
interior rows 2A (see distribution under
ordering and page 2)
• CCT: 3000K (80 CRI), 4000K (70 CRI),
5000K (70 CRI), and turtle friendly Amber
LED options
Electrical:
• Universal input voltage 120-277 VAC,
50/60 Hz
• Integral step-down transformer for 347V
& 480V
• Ambient operating temperature -40˚ C to 40˚ C
Automatic thermal self-protection
Drivers have greater than 90% power
factor and less than 10% THD
Optional continuous dimming to 10% or
dual circuitry available
• LED drivers have output power over-
voltage, over-current protection and short
circuit protection with auto recovery
1050 mA driver available with 90L con-
figuration for increased lumen output
• LED electrical assembly, including PR
devices, consumes no power in
the ‘off’ state
Surge protection – 20KA; Turns fixture off
at end of life; Includes LED for end of life
indication (see surge suppressor page 4)
Controls:
Drivers are 0-10V dimming standard.
Photocell, occupancy sensor and wireless
controls available for complete on/off
and dimming control
Lumen maintenance:
L90 at 60,000 hours (Projected per IESNA
TM-21-11)
Installation:
Two die-cast aluminum arm designs: The
decorative arm offers a sleek upswept look
while the straight arm follows the housing’s
contoured lines for continuity of style
Fixture ships with arm installed for ease of
installation and mounts to #2 drill pattern
Wall bracket, mast arm fitter and pole
accessories are also available
allowing easy mounting for virtually
any application
Finish:
TGIC thermoset polyester powder paint
finish applied at nominal 2.5 mil thickness
Warranty:
Five year limited warranty (for more infor-
mation visit: http://www.hubbelloutdoor.com/
resources/warranty/
Listings:
Listed to UL1598 and CSA C22.2#250.0-
24 for wet locations
Models meet DesignLights Consor-
tium (DLC) qualifications, consult
DLC website for more details:
http://www.designlights.org/QPL
• IDA approved • IP65
90 LED 3/4 VIEW 30 LED
LED Product Partner
CERTIFICATIONS/LISTINGS
DIMENSIONS
PRODUCT IMAGE(S)
SPECIFICATIONS
60 LED 90 LED
C
Upswept Arm
Straight Arm
A
A
B
B
D
E
F
G
ORDERING INFORMATION SEE NEXT PAGE
Cat.#
Approvals
Job Type
Spaulding Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2016 SPAULDING LIGHTING, All Rights ReservedFor more information visit our website: www.spauldinglighting.com • Printed in USA CL1LED-SPEC 4/16
*3000K and warmer CCTs only
ORDERING INFORMATION ORDERING EXAMPLE: CL1-A-90LU-5K-3-DB-RPA3
Notes: 1- For BL option 90L and 60L; N/A 347V & 480V
2 - BL & CD cannot be combined
3 - Fuse option not available with universal voltage
4 - Select F3 fusing option for 220V
5 - Photocell receptacle not available with BL option
6 - Recommended for Type III and IV distributions only
7 - Available in 350mA drive current only Type IV, 5M
8 - 0-10V fully adjustable dimming with automatic daylight calibration and
different time delay settings, must order minimum of one SCP-REMOTE
control to program dimming settings (see accessories)
9 - Must specify 120V, 208V, 240V or 277V; not available with
PR option; consult factory for 347V and 480V application, not available
with BL or CD options.
10 - Not available with AD arm
11 - Not available with 480V
12 - Not available with 347V or 480V
13 - Not available with WIR or WIRSC
14 - Not available with SCO, SCL, SCP or SCPW
NO. OF LEDS
90L
90 High brightness LEDs
60L
60 High brightness LEDs
30L
30 High brightness LEDs
SERIES
CL1
Cimarron LED
MOUNTING
AArm mount construction (6” straight
rigid arm included & acceptable for 90°
configurations)
AD Decorative arm mount const. (6” decora-
tive upswept arm incl. & acceptable for
90° configurations)
MAF Mast arm fitter for mounting to standard
2 3/8" mast arm bracket, includes 6"
straight rigid arm
COLOR
DB
Dark Bronze
BL
Black
WH
White
GR
Gray
PS
Platinum Silver
RD
Red
(premium color)
FG
Forest Green
(premium color)
CC Custom Color
OPTIONS
BC6Backlight control
CD2Continuous dimming
WB Wall bracket
RPA3 3” Round pole adapter
RPA4 4” Round pole adapter
RPA5 5” Round pole adapter
RPA6 6” Round pole adapter
F(X)3,4 Fusing (replace X with
voltage: 1-120V, 2-208V,
3-240V, 4-277V, 5-480V,
F-347V)
VG Vandal guard
7PR Photocell receptacle (7-pin
ANSI C136.41—2013 recep-
tacle for use with standard
Twist-Lock® photo controls,
shorting caps, and ANSI
C136.41 external wireless
control devices. Select SCL
option to add occupancy sens-
ing capability when using with
compatible external wireless
devices.
CL1
CCT
3K
3000K
4K
4000K
5K
5000K
AM7
Amber (590 nm
available for
“Turtle Friendly”
applications
(consult factory)
DISTRIBUTION
2Type II
3Type III
4Type IV
5M Type V Medium
5S Type V Short
5W Type V Wide
2L Type II Rotated 90° left
3L Type III Rotated 90° left
4L Type IV Rotated 90° left
2R Type II Rotated 90° right
3R Type III Rotated 90° right
4R Type IV Rotated 90° right
1A Auto Front Row Type I
1AR Auto Front Row Type I Rotated 90° right
1AL Auto Front Row Type I Rotated 90° left
2A Auto Front Row Type II
2AR Auto Front Row Type II Rotated 90° right
2AL Auto Front Row Type II Rotated 90° left
VOLTAGE
U3
Universal 120V-277V,
50/60 Hz
1120V
2208V
3240V
4277V
5
480V, 60 Hz
F
347V, 60 Hz
E4
220V, 50 Hz
DRIVE CURRENT
Leave blank for
700mA (standard)
035 350mA Amber
CCT only
105 1050 mA (use with
90L only for higher
lumen output)
Spaulding Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2016 SPAULDING LIGHTING, All Rights ReservedFor more information visit our website: www.spauldinglighting.com • Printed in USA CL1LED-SPEC 4/16
PIR MOTION/OCCUPANCY
CONTROL OPTIONS
SCO10,12,13 On/Off control (line voltage device not
for use with 7PR receptacle option and
external wireless control devices)
SCL10,12,13 Add-on occupancy sensor for use with
ext. wireless control device connected
thru 7PR receptacle. Consult control
manufacturer for compatibility.
SCP8,10,12,13 Programmable dimming control (line
voltage device not for use with 7PR
receptacle option and external wire-
less control devices). A minimum of
one SCP-REMOTE accessory remote
control required for configuration;
(Standard lens with greater sensitivity;
motion detection radius equal to .75
X luminaire mounting height (approx.
distance)
SCPW8,10,12,13 Programmable dimming control
(line voltage device not for use
with 7RP receptacle option and
external wireless control devices);
A minimum of one SCP-REMOTE
accessory remote control re-
quired for configuration. (Wide
lens with motion detection radius
equal to 1.3 X luminaire mounting
height (approx. distance)
WIRELESS CONTROL OPTIONS
WIR11,14 wiSCAPE Fixture Module, in-fixture
relay for wireless lighting control
WIRSC10,12,14 wiSCAPE Fixture Module, in-fixture
relay for wireless lighting control and
motion/occupancy control
CONTROLS GUIDE
As energy codes become more restrictive and we push for
sustainable lighting designs, the integration of lighting controls
and luminaires have become more and more important. Hubbell
Lighting offers numerous outdoor lighting controls solutions for
the most demanding applications. Visit the link below to learn
more about energy-saving controls.
www.hubbelllighting.com/solutions/controls/
#LEDS
DRIVE
CURRENT
SYSTEM WATTS
DIST.
TYPE
5K
(5000K nominal, 70 CRI)
4K
(4000K nominal, 70 CRI)
Amber
(590 )
LUMENS LPW1B U G LUMENS LPW1B U G LUMENS LPW1BUG
120-277V
347-480V
30
700 mA
70W 80W
1A 8244 118 1 0 1 8162 117 1 0 1 — — —
2A 8202 117 1 0 1 8121 116 1 0 1 — — —
2
110
2
0
3
7639
109
2
0
2
3
110
2
0
2
7635
109
2
0
2
4
111
1
0
2
7726
110
1
0
2
5S
120
3
0
0
8291
118
3
0
0
5M 7940 113 3 0 1 7862 112 3 0 1 — — —
5W
110
3
0
2
7591
108
3
0
2
60 135W 150W
1A
120
1
0
2
16011
119
1
0
1
2A
119
1
0
2
15929
118
1
0
2
2
112
3
0
3
14984
111
3
0
3
3
112
3
0
3
14977
111
3
0
3
415306 113 2 0 3 15154 112 2 0 3 2488 51 001
5S
122
4
0
0
16263
120
4
0
0
5M
115
4
0
2
15421
114
4
0
2
2533
51
2
0
1
5W
111
4
0
3
14891
110
4
0
3
90 205W 225W
1A
116
2
0
2
23546
115
2
0
2
2A
115
2
0
2
23425
114
2
0
2
2
109
3
0
4
22035
107
3
0
4
3
109
3
0
4
22026
107
3
0
4
422509 110 3 0 4 22286 109 3 0 4 3558 76 101
5S 24156 118 5 0 0 23916 117 5 0 0 — — —
5M 22905 112 4 0 2 22678 111 4 0 2 3596 76 201
5W
108
5
0
3
21899
107
5
0
3
90 1050mA 325W 350W
1A
98
2
0
2
31394
97
2
0
2
2A
97
2
0
2
31233
96
2
0
2
2
91
4
0
5
29380
90
3
0
5
3
91
3
0
4
29367
90
3
0
4
4
92
3
0
5
29714
91
3
0
5
5S
99
5
0
0
31888
98
5
0
0
5M
94
5
0
3
30237
93
5
0
3
5W
91
5
0
4
29198
90
5
0
4
COVER
CAST ADAPTER
CAST ADAPTER
THREADED ROD
GASKET
FLAT WASHER
SCREW
COVER
LOCKWASHER
HEX NUT
RETAINER WASHER
ARM
CAST ARM
FIXTURE
TO
HOUSING
(3-HOLE PATTERN END)
SQUARE POLE COVER
POLE COVER POLE COVER
POLE TOP
.875
Ø .875
HOLE
3.875
3.5
Ø .563
3 HOLES
ROUND POLE
ROUND POLE
SQUARE POLE
SQUARE & ROUND POLES
UPSWEPT ARM MOUNT
SQUARE & ROUND POLES
#2 DRILL PATTERN FOR POLES
NUT PLATE
NUT PLATE
NUT PLATE
SQUARE POLE
COVER
CAST ADAPTER
CAST ADAPTER
THREADED ROD
GASKET
FLAT WASHER
SCREW
COVER
LOCKWASHER
HEX NUT
RETAINER WASHER
ARM
CAST ARM
FIXTURE
TO
HOUSING
(3-HOLE PATTERN END)
SQUARE POLE COVER
POLE COVER POLE COVER
POLE TOP
.875
Ø .875
HOLE
3.875
3.5
Ø .563
3 HOLES
ROUND POLE
ROUND POLE
SQUARE POLE
SQUARE & ROUND POLES UPSWEPT ARM MOUNT
SQUARE & ROUND POLES
#2 DRILL PATTERN FOR POLES
NUT PLATE
NUT PLATE
NUT PLATE
SQUARE POLE
3.30
5.62
1.16
5.59
3.40
1.95
1.95
3.89
.83
5.62
1.16
1.95
3.89
5.59
3.40
1.95
2.50
MAF – HORIZONTAL MAST ARM FITTER
ACCESSORIES/REPLACEMENT PARTS - Order Separately
Catalog Number Description
CR-RPA3-XX1Round pole adapter for straight arm (314 - 334”)
CR-RPA4-XX1Round pole adapter for straight arm (378 - 412”)
CR-RPA5-XX1Round pole adapter for straight arm (5”)
CR-RPA6-XX1Round pole adapter for straight arm (6”)
CRD-RPA2-XX1Round pole adapter for upswept arm (234 - 318”)
CRD-RPA3-XX1Round pole adapter for upswept arm (314 - 334”)
CRD-RPA4-XX1Round pole adapter for upswept arm (378 - 412”)
CRD-RPA5-XX1Round pole adapter for upswept arm (5”)
CRD-RPA6-XX1Round pole adapter for upswept arm (6”)
WB-CR-XX1Wall bracket
TPLB-XX1Twin parallel luminaire bracket
MAF-CL-XX3Horizontal mast arm fitter for 2 3/8” OD arm. Mounts to standard
6” arm (ordered with fixture)
1 - Replace XX with color choice, eg.: DB for Dark Bronze 2 -When ordering poles, specify Pole Drill Pattern #2 3 - Fixture must include standard 6” arm
Spaulding Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2016 SPAULDING LIGHTING, All Rights ReservedFor more information visit our website: www.spauldinglighting.com • Printed in USA CL1LED-SPEC 4/16
Catalog Number Description
SCP-REMOTE9Remote control for SCP option. Order at least
one per project to program and control.
93052458 20KA surge protection with an end of life LED
indicator
AUTOMOTIVE DEALERSHIP OPTICS
For Automotive Dealership applications Spaulding Lighting has developed two optics designed for
enhanced and proper lighting of the auto dealership merchandise and the front row 1A and interior
rows 2A (See CL1 distribution information for details)
1A - Front Row Auto Optic 2A - Drive Lane Auto Optic
Optic 1A
Maximum illumination on front row display
Maximum pole spacing
Optic 2A
Excellent front row illumination and drive lane
Optimal uniformity for drive lane and interior rows
ENERGY DATA
Power Factor
>.9
Total Harmonic
Distortion
<10%
ENERGY SAVING DATA
SURGE PROTECTION
Spaulding Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2016 SPAULDING LIGHTING, All Rights ReservedFor more information visit our website: www.spauldinglighting.com • Printed in USA CL1LED-SPEC 4/16
• Field replaceable surge protection device (SPD) provides 20KA and 10KV protection meeting ANSI/IEEE
C62.41.2 Category C High and Surge Location Category C3
The SPD is designed with a clamping voltage of 1600V at 20KA using industry standard 8/20µs waveform
Max surge current = 20,000 Amps (see table)
LED Indicator – Green LED is unlit at end of life
Pulse Rating
(8 x 20 µSec)
Strikes Surge
120,000 A
215,000 A
15 10,000 A
120 3,000 A
cRUus CE
In10KA 5KA
MOTION CONTROLS
P
o
l
e
S
h
a
d
o
w
P
o
l
e
S
h
a
d
o
w
P
o
l
e
S
h
a
d
o
w
SCP - Designed for intermediate coverage area
SCPW - Designed for widest coverage area
Vehicle detection is possible however less reliable than human detection; Vehicle detection is
dependent upon the following: rate of speed, mounting height of luminaire and vehicle temperature
Start up delay from initial motion detection to
fixture illumination is approximately 1-2 seconds
Note: Extreme heat or cold temperatures may limit detection.
Note: Extreme heat or cold temperatures may limit detection.
P
o
l
e
S
h
a
d
o
w
60
30
30
r = .75 x h
d = 1.5 x h
P
o
l
e
S
h
a
d
o
w
60
30
30
r = .75 x h
d = 1.5 x h
P
o
l
e
S
h
a
d
o
w
60
30
30
r = .75 x h
d = 1.5 x h
Catalog Number Description
SETA-XX1 Square pole tenon adapter (4 at 90 degrees)
RETA-XX1 Round pole tenon adapter (4 at 90 degrees)
TETA-XX1 Hexagonal pole tenon adapter (3 at 120 degrees)
1 Replace XX with color choice, eg.: DB for Dark Bronze
TENON TOP POLE BRACKET ACCESSORIES
(2 3/8” OD tenon) (RSS version requires 4” round pole adapter)
PHOTOCONTROL EQUIPMENT
MOUNTING ACCESSORIES
Catalog Number Description
PTL-1 Photocontrol - twist-lock cell (120V)
PTL-8 Photocontrol - twist-lock cell (120-277V)
PTL-5 Photocontrol - twist-lock cell (480V)
PTL-6 Photocontrol - twist-lock cell (347V)
PSC Shorting cap - twist-lock
Catalog Number Description
ARM-CL-K-TA-XX1Adjustable mounting arm for single fixture (2-3/8 tenon) – 5 lbs. 2.3 kgs.
ARM-CL-TK-TA-XX1Adjustable mounting arm for two fixtures at 180˚ (2-3/8 tenon) – 7 lbs. 3.2 kgs.
ARM-CL-K-S-XX110” adjustable arm – .5 lbs. .05 kgs. – 5.75 lbs. 2.6 kgs.
1 Replace XX with color choice, eg.: DB for Dark Bronze
2 Fixture must include standard 6” straight arm
MAL-KF-X
MAL-TK-X
ARM-CL-K-TA-XX ARM-CL-K-S-XX
ARM-CL-TK-TA-XX

Navigation menu