ERROR CODE – AND THEIR MEANING CODES/ERROR

ERROR CODES/ERROR CODE ERROR CODE

ERROR CODES/ERROR CODE ERROR CODE

ERROR CODES/ERROR CODE ERROR CODE

User Manual: Pdf ERROR CODES/ERROR CODE

Open the PDF directly: View PDF PDF.
Page Count: 3

DownloadERROR CODE – AND THEIR MEANING CODES/ERROR
Open PDF In BrowserView PDF
T2000 & T3000 ERROR CODES
The information supplied here is to be used only as a guide. Not all codes apply to all models
and some codes are model specific. This information is provided to assist in determining the
cause of a problem only. In some instances, the error message may be caused by an error
in a completely different location, in these cases the error message may be of little value.

01=HEAP OVERLAP
02=HEAP EXHAUSTED
03=INVALID HEAP ADDRESS
04=INVALID TASK NUMBER
05=INVALID TIMER NUMBER
06=INVALID TIMER
07=INVALID MESSAGE CATEGORY or PATH
08=INVALID MESSAGE CODE or TYPE
09=SOFTWARE INTERRUPT
10=INVALID QUEUE NUMBER
11=INVALID USER CHAR
12=INAPPROPRIATE TAST TYPE
13=ILLEGAL OPCODE
14=XIRQ INTERRUPT
15=CANT CREATE ANY MORE TIMERS
16=CANT CREATE ANY TIMERS
17=TIMER DOES NOT EXIST
18=TIMER ALREADY EXISTS
19=INVALID TIMER VECTOR
20=INVALID CODEWORD RECEIVED
21=INDICATOR BYTE ERROR
22=TRANSMISSION TIMEOUT
23=CODEWORD FIELD PARAMETER
24=INVALID CALL REQUEST
25=TEST MODE RESET VECTOR INCORRECT
26=TASK SUSPENSION CALL
27=TASK QUEUE
28=n/a
29=n/a
30=MSK RX CRC NOT READY
31=MSK TX TIMER
32=MSK TX INTERRUPT
33=MSK TX CRC NOT READY
34=MAK TX UNLOCKED
35=n/a
36=n/a
37=n/a
38=n/a
39=n/a
40=INVALID MESSAGE
41=INVALID PERSONALITY
42=INVALID DATA
43=LOGON CHAR
44=INVALID LOGPERS STATUS
45=INVALID LOGPERS POWERUP MESS
46=INVALID LOGPERS NEXT STATE
47=n/a

ERROR CODE.DOC

48=n/a
49=n/a
50=INVALID BCD DATA
51=MESSAGE DATA
52=STACK OVERFLOW
53=INVALID STRING STORE OVERFLOW
54=INVALID QUEUE BUTTON
55=INVALID QUEUE TIMEOUT
56=DISPLAY MODE
57=LANGUAGE POINTER UNINITIALISED
58=INVALID QUEUE DOSPLAY
59=INVALID QUEUED
60=INVALID TRUNKPERS MODE
61=SDMQUEUE FULL
62=SDM RX
63=FLASH PERSONALITY INVALID
64=n/a
65=n/a
66=n/a
67=n/a
68=INVALID CHANNEL NUNBER
69=CHANNEL BLOCK CACULATION
70=SYSNT FREQUENCY NUMBER TOO BIG
71=ILLEGAL TRANSMITTER POWER LEVEL
72=INAPPROPRIATE DATABASE ITEM TYPE
73=INVALID ANN NUMBERING MODEL
74=INVALID BAUD RATE
75=UNPROGRAMMER DYNAMIC ITEM
76=INVALID GROUP ADDRESS
77=INVALID PRESET CALL
78=INVALID DIALLING SCHEME
79=INVALID PRESET LABEL
80=RX OVERFLOW
81=AUDIO TONE FUNCTION
82=INVALID AUDIO TONE NUMBER
83=CCI RX BUFFER OVERFLOW
84=INVALID CALL TYPE

Page 1 of 3

24/07/02

1 to 12

µProcessor tasks

Processor unable to perform errors task due to software
or hardware fault (catastrophic condition).

13

Illegal opcode

14 to 21

Timer and
processing errors

22

Transmission
timeout

30
31 to 33
34

FFSK receive error
FFSK transmit error
Synthesiser not
locked
Software error
codes
Programming errors

Illegal operating code due to:
- Eprom corruption
- Ctrl board hardware failure.
- The µP has detected an invalid EPROM value.
The µProcessor cannot function due to software or
hardware problems. The µP’s XIRQ line has a low
present. This line should always be high.
An FFSK transmission has not been completed within an
appropriate time (check TXSYNC line from the MODEM
to the µP). The µP has not received proper syncronising
signals from the FFSK modem during transmit mode.
FFSK CRC calculation error.
FFSK to be transmitted corrupted or FFSK timing error.
Synthesiser taking too long to lock up.

40 to 60
70 to 79

Not helpful for servicing.
Incorrect programming of the radio. Causes:
- Wrong programming software used.
- Wrong or invalid data programmed into radio.

T2000 - Out of lock indication
T2010
T2015
T2020

The active channel light is on and all other channel lights flash.
The right hand channel digit flashes.
Both BUSY & TX lights flash.

Trunking error messages
U1 – ESN – ERROR
U2 – DATA – ERROR
U3 – ECC – ERROR

UA0
UA1
UA2
UA3
UA4

ERROR CODE.DOC

The radios ESN, has become corrupt. The radio will have to be
returned to TAIT to be re-formatted.
The programming of the radio has been lost or corrupt.
Programme the radio.
Either the wrong firmware has been fitted to the logic board, in
which case fitting the correct firmware should clear the problem.
Or the ECC has become corrupt, in which case the radio should
be returned to TAIT.
Function unavailable.
Out of range, no communications with the network.
Called unit, out of range, or switched off.
Invalid selection.
Called unit engaged – try again later.

Page 2 of 3

24/07/02

Specific errors
ERROR MESSAGE
Error 0
Error 02

MODEL
T700
ALL

Error 02

ALL

Error 13

ALL

Error 14

ALL

Error 22

ALL

Error 31

ALL

Error 34
Error 68
Error 70
Error 70

ALL
ALL
T2035
ALL
trunking

Error 75

ALL

Error 80

ALL

CONF--ERR

T2020
T2030
T2035
T2040
T2050

PROG

T2020
T2040
T2050

ERROR CODE.DOC

ACTION
RAM problem.
A request for a block of dynamic memory from the heap
cannot be satisfied, as there is insufficient memory
available.
The available memory inside the µP, for storing events,
has been used up. For example this error may occur if the
PTT is repeatedly used in quick succession.
The µP has encountered an illegal instruction. This
should not happen in normal use but may occur if there is
a problem on the µP bus.
The µP has detected a logic low on it's XIRQ pin. This line
should always stay high.
The µP is not receiving correct synchronisation signals
form the FFSK modem during transmit mode.
The µP could not reply to an incoming code word within
the required time.
TX VCO out of lock.
The radio has tried to tune to an invalid channel number.
Change firmware to v3.10 or later.
The channel number the radio has just selected is invalid
(not permitted according to the network parameters). This
may occur if a mistake is made during programming and
the network parameters "highest and lowest channel in
network" have been set wrongly, or changed after setting
all other channel parameters.
The frequency of the channel, which has just been
selected, is invalid (outside the limits allowed for the
radio). This error is usually the result of setting up the
channel blocks (trunking) incorrectly at the time it was
programmed.
The micro is receiving a continuos active signal on the
serial link from the control head (T700TR's), or
programming equipment (T500TR's). This will be visible
as a low logic level at the serial input port of the µP.
This happens if the radio's configuration codes become
corrupt. Switch off radio, short "factory" test points,
switch on radio for 5 seconds, switch off radio and
remove link. When the radio is switched back on it should
show "PROG", if so programme the radio with a known
good file. Trunking radios may still not work and may
need to be returned to Tait to have their electronic serial
numbers re programmed.
The radio has lost it's setup information. Re-program with
a known good setup file.

Page 3 of 3

24/07/02
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Producer                        : Acrobat Distiller 4.0 for Windows
Creator                         : Microsoft Word 8.0
Modify Date                     : 2002:07:24 16:22:02+10:00
Author                          : Alan Prank
Title                           : ERROR CODE – AND THEIR MEANING
Create Date                     : 2002:07:24 16:21:53
Page Count                      : 3
Page Mode                       : UseNone
EXIF Metadata provided by EXIF.tools

Navigation menu