EN 300440
2016-04-12
: Pdf En 300440 EN_300440 CertsReports 525824 ProductFiles
Open the PDF directly: View PDF 
.
Page Count: 31
| Download | |
| Open PDF In Browser | View PDF |
Shenzhen SEM.Test Technology Co., Ltd. Radio Measurement and Test Report For Winstars Technology Limited t Block 4, TaiSong Industrial Park, DaLang Street, LongHua Town, Bao’an es district, Shenzhen, China EN 300 440-1 V1.6.1 (2010-08) EN 300 440-2 V1.4.1 (2010-08) Test Standards: Product Description: High Power Wi-fi AP/Router WS-WN570HA1 SE M. T Tested Model: Report No.: STR15098069E-2 Tested Date: 2015-09-08 to 2015-09-22 Issued Date: 2015-09-22 Tested By: Jack Kang / Engineer Reviewed By: Silin Chen / Engineer Approved & Authorized By: Jandy So / PSQ Manager Prepared By: Shenzhen SEM.Test Technology Co., Ltd. 1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C.（518101） Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen SEM.Test Technology Co., Ltd. REPORT NO.: STR15098069E-2 PAGE 1 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. TABLE OF CONTENTS 1 GENERAL INFORMATION ..................................................................................................................................... 3 1.1 Product Description for Equipment Under Test (EUT) .................................................................................... 3 1.2 Test Standards ................................................................................................................................................... 4 1.3 Test Methodology ............................................................................................................................................. 4 1.4 Test Facility ....................................................................................................................................................... 4 1.5 EUT Setup and Test Mode ................................................................................................................................ 5 1.6 Measurement Uncertainty ................................................................................................................................. 5 1.7 Test Equipment List and Details ....................................................................................................................... 6 2. SUMMARY OF TEST RESULTS ............................................................................................................................. 7 t 3. EQUIVALENT ISOTROPICALLY RADIATED POWER ..................................................................................................... 8 3.1 Standard Applicable .......................................................................................................................................... 8 3.2 Test Procedure ................................................................................................................................................... 8 3.3 Summary of Test Results .................................................................................................................................. 9 es 4. PERMITTED RANGE OF OPERATING FREQUENCIES .................................................................................................. 10 4.1 Applicable Standard ........................................................................................................................................ 10 4.2 Test Procedure ................................................................................................................................................. 10 4.3 Test Results/Plots ............................................................................................................................................ 11 5. SPURIOUS EMISSIONS ................................................................................................................................................. 13 5.1 Limit of Spurious Emissions........................................................................................................................... 13 5.2 Test Procedure ................................................................................................................................................. 13 5.3 Environmental Conditions .............................................................................................................................. 13 5.4 Summary of Test Results/Plots ....................................................................................................................... 13 SE M. T 6. DUTY CYCLE .............................................................................................................................................................. 21 6.1 Applicable Standard ........................................................................................................................................ 21 6.2 Test Procedure ................................................................................................................................................. 21 6.3 Environmental Conditions .............................................................................................................................. 21 6.4 Summary of Test Results/Plots ....................................................................................................................... 21 7. RECEIVER SPURIOUS EMISSIONS ............................................................................................................................... 22 7.1 Limit of Spurious Emissions........................................................................................................................... 22 7.2 Test Procedure ................................................................................................................................................. 22 7.3 Environmental Conditions .............................................................................................................................. 22 7.4 Summary of Test Results/Plots ....................................................................................................................... 22 EXHIBIT 1 - PRODUCT LABELING ........................................................................................................................ 25 Proposed CE Label Format ................................................................................................................................... 25 Proposed Label Location on EUT......................................................................................................................... 25 EXHIBIT 2 - EUT PHOTOGRAPHS.......................................................................................................................... 26 EXHIBIT 3 - TEST SETUP PHOTOGRAPHS .......................................................................................................... 30 REPORT NO.: STR15098069E-2 PAGE 2 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 1 GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) General Description of EUT Product Name: Trade Name: Model No.: Adding Model(s): Rated Voltage: High Power Wi-fi AP/Router N/A WS-WN570HA1 525824 DC 24V from adapter Model: TDX-2400500 Input: AC 100-240V 50/60Hz, Output: DC 24V 0.5A SE M. T Power Adaptor Model: t Manufacturer: Address of manufacturer: Winstars Technology Limited Block 4, TaiSong Industrial Park, DaLang Street, LongHua Town, Bao’an district, Shenzhen, China Winstars Technology Limited Block 4, TaiSong Industrial Park, DaLang Street, LongHua Town, Bao’an district, Shenzhen, China es Client Information Applicant: Address of applicant: Note: The test data is gathered from a production sample, provided by the manufacturer. Technical Characteristics of EUT Wi-Fi(5.8G) Support Standards: Frequency Range: RF Output Power: Type of Modulation: Quantity of Channels Channel Separation: Type of Antenna: Antenna Gain: REPORT NO.: STR15098069E-2 802.11ac 5775-5825MHz for 802.11a 13.52dBm (EIRP) BPSK/QPSK/16QAM/64QAM/256QAM 6 for 802.11ac 10MHz External Antenna 7.0dBi PAGE 3 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 1.2 Test Standards The following report is prepared on behalf of the Winstars Technology Limited in accordance with ETSI EN 300 440-2, Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive. t The objective of the manufacturer is to determine compliance with ETSI EN 300 440-2, Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive. 1.3 Test Methodology es Maintenance of compliance is the responsibility of the manufacturer. Any modification of the product maybe which result in lowering the immunity should be checked to ensure compliance has been maintained SE M. T All measurements contained in this report were conducted with ETSI EN 300 440-1, Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 1: Technical characteristics and test methods. The equipment under test (EUT) was configured to measure its highest possible emission level. For more detail refer to the Operating Instructions. 1.4 Test Facility FCC – Registration No.: 934118 Shenzhen SEM.Test Technology Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files and the Registration is 934118. Industry Canada (IC) Registration No.: 11464A The 3m Semi-anechoic chamber of Shenzhen SEM.Test Technology Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 11464A. CNAS Registration No.: L4062 Shenzhen SEM.Test Technology Co., Ltd. is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L4062. All measurement facilities used to collect the measurement data are located at 1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao’an District, Shenzhen, P.R.C (518101). REPORT NO.: STR15098069E-2 PAGE 4 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 1.5 EUT Setup and Test Mode The equipment under test (EUT) was configured to measure its highest possible emission/immunity level. The test modes were adapted according to the operation manual for use, the EUT was operated in the engineering mode to fix the Tx frequency that was for the purpose of the measurements, more detailed description as follows: Test Mode List Description Remark TM1 Low Channel 5775 MHz TM2 Middle Channel 5805 MHz TM3 High Channel 5825 MHz t Test Mode Test Conditions Temperature (℃) 20 Voltage (V) AC 230V Special Cable List and Details LTHV HTHV HTLV -20 -20 55 55 AC 207V AC 253V AC 207V AC 253V Length (m) Shielded/Unshielded With / Without Ferrite DC Cable 1.0 Unshielded Without Ferrite RJ45 Cable 1.0 Unshielded Without Ferrite Manufacturer Model Serial Number Lenovo E10 LR-63C8R SE M. T Cable Description LTLV es Normal Auxiliary Equipment List and Details Description Notebook 1.6 Measurement Uncertainty Measurement uncertainty Parameter Conditions Uncertainty EIRP Conducted ±0.42dB Frequency Range --- ±1×10-7 Transmitter Spurious Emissions Radiated ±5.2dB Receiver Spurious Emissions Radiated ±5.2dB REPORT NO.: STR15098069E-2 PAGE 5 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 1.7 Test Equipment List and Details Manufacturer Agilent E4407B Serial Number MY41440400 2016-06-16 Spectrum Analyzer Agilent N9020A US47140102 2016-06-16 Signal Generator Agilent 83752A 3610A01453 2016-06-16 Power Divider Weinschel 1506A PM204 2016-06-16 Spectrum Analyzer Rohde & Schwarz FSP 836079/035 2016-06-16 EMI Test Receiver Rohde & Schwarz ESVB 825471/005 2016-06-16 Amplifier Agilent 8447F 3113A06717 2016-06-16 Amplifier C&D PAP-1G18 2002 2016-06-16 Broadband Antenna Schwarz beck VULB9163 9163-333 2016-06-16 Horn Antenna ETS 3117 00086197 2016-06-16 DC Power Supply LW APR-3003 N/A 2016-06-16 Attenuator ATTEN es Model ATS100-4-20 Due. Date / 2016-06-16 SE M. T Description t Spectrum Analyzer REPORT NO.: STR15098069E-2 PAGE 6 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 2. SUMMARY OF TEST RESULTS EN 300440-1 V1.6.1 (2010-08) Reference Description of Test Item Result 7.1.3 Equivalent Isotropically Radiated Power Pass 7.2.4 Permitted Range of Operating Frequencies Pass 7.3.6 Spurious Emissions Pass 7.4.3 Duty Cycle Pass 7.5.1 Additional requirements for FHSS equipment N/A 8.3.5 Receiver Spurious Radiations Pass t Standards SE M. T es Pass: The EUT complies with the essential requirements in the standard Fail: The EUT does not comply with the essential requirements in the standard N/A: not applicable REPORT NO.: STR15098069E-2 PAGE 7 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 3. Equivalent Isotropically Radiated Power 3.1 Standard Applicable SE M. T es t According to ETSI EN 300 440-1 section 7.1.3, the effective radiated power shall not exceed the power class value given in following table: 3.2 Test Procedure According to section 7.1.2 of the standard EN 300440-1, the test procedure shall be as follows: 1. Using a suitable means, the output of the transmitter shall be connected to the spectrum analyzer, the spectrum analyzer shall be capable of faithfully reproducing the envelope peaks and the duty cycle of the transmitter output signal. The observed duty cycle of the transmitter (Tx on/(Tx on + Tx off)) shall be noted as x, (0 < x < 1) and recorded. 2. The average output power of the transmitter shall be determined using the spectrum analyzer. The observed value shall be recorded as "A" (in dBm). 3. The e.i.r.p. shall be calculated from the above measured power output A, the observed duty cycle x, and the applicable antenna assembly gain "G" in dBi, according to the formula: - P = A + G + 10 log (1/x); 4. The measurement shall be repeated at the lowest, the middle, and the highest frequency of the stated frequency range.These frequencies shall be recorded. FHSS equipment shall be made to hop continuously to each of these three frequencies separately. These measurements shall be performed at normal and extreme test conditions. REPORT NO.: STR15098069E-2 PAGE 8 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 3.3 Summary of Test Results Test Conditions Measured Value Antenna Gain EIRP Limit dBm dBi dBm dBm Low Channel (5775MHz) 6.52 7 13.52 13.98 LTLV 6.42 7 13.42 13.98 LTHV 6.30 7 13.30 13.98 HTHV 6.09 7 13.09 13.98 HTLV 6.28 7 13.28 13.98 Middle Channel (5805MHz) 5.89 7 12.89 13.98 LTLV 5.85 7 12.85 13.98 LTHV 5.79 7 12.79 13.98 HTHV 5.69 7 12.69 13.98 HTLV 5.76 7 12.76 13.98 7 12.62 13.98 7 12.56 13.98 7 12.59 13.98 es Normal t Normal High Channel (5825MHz) 5.62 LTLV 5.56 LTHV 5.59 SE M. T Normal HTHV 5.61 7 12.61 13.98 HTLV 5.46 7 12.46 13.98 REPORT NO.: STR15098069E-2 PAGE 9 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 4. Permitted Range of Operating Frequencies 4.1 Applicable Standard According to EN 300 440-1 section 7.2 4.2 Test Procedure es t The frequency range of the equipment is determined by the lowest and highest frequencies occupied by the power envelope in accordance with CEPT/ERC Recommendation 74-01 [2]. fH is the highest frequency of the power envelope, it is the frequency furthest above the frequency of maximum power where the output power drops below the level of –75 dBm/Hz spectral power density (-30 dBm if measured in a 30 kHz reference bandwidth) eirp. fL is the lowest frequency of the power envelope; it is the frequency furthest below the frequency of maximum power where the output power drops below the level of –75 dBm/Hz spectral power density (-30 dBm if measured in a 30 kHz reference bandwidth) eirp. SE M. T According to section 7.2.2 of the standard EN 300440-1, the test procedure shall be as follows: 1. Put the spectrum analyzer in video averaging mode with a minimum of 50 sweeps selected. 2. Select the lowest operating frequency of the equipment under test and activate the transmitter with modulation applied. The RF emission of the equipment shall be displayed on the spectrum analyzer. 3. Using the marker of the spectrum analyzer, find lowest frequency below the operating frequency at which spectral power density drops below the required value. 4. Select the highest operating frequency of the equipment under test and find the highest frequency at which the spectral power density drop below the required value. 5. The difference between the frequencies measured in step 3 and step 4 is the operating frequency range. The equivalent isotropically radiated power is then calculated from the measured value, the known antenna gain, relative to an isotropic antenna, and if applicable, any losses due to cables and connectors in the measurement system. REPORT NO.: STR15098069E-2 PAGE 10 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 4.3 Test Results/Plots Test Conditions Frequencies (MHz) at -30dBm/30kHz (EIRP) Lowest Frequency (fL) Highest Frequency (fH) Normal 5731.16 5868.94 LTLV 5731.24 5868.86 LTHV 5731.24 5868.86 HTHV 5731.16 5868.94 HTLV 5731.16 5868.94 t The frequency range lies within the band 5725MHz to 5875MHz (fL > 5725MHz and fH < 5875MHz), fullfit the requirements of the standard. SE M. T es Test plots hereby for reference with the normal case: REPORT NO.: STR15098069E-2 PAGE 11 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. SE M. T es t Lowest Frequency Channel Edge for reference: Highest Frequency Channel Edge for reference: REPORT NO.: STR15098069E-2 PAGE 12 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 5. Spurious Emissions 5.1 Limit of Spurious Emissions t The power of any spurious emission shall not exceed the following values given in the following table. es 5.2 Test Procedure The EUT was placed on a nonmetal table which is 1.5 meter above the grounded reference plane and set to work in normal operation mode. Details refer to EN 300 440-1 subclause 7.3.4. The EUT was operating at transmitting mode to represent worst case during final qualification test. SE M. T 5.3 Environmental Conditions Temperature: 23 °C Relative Humidity: 45% ATM Pressure: 1014 mbar 5.4 Summary of Test Results/Plots According to the data sheet, the EUT complied with the EN 300 440 standards, and had the worst margin of: -5.41 dB at 851.0353 MHz in the Horizontal polarization, High Channel, 3Meters REPORT NO.: STR15098069E-2 PAGE 13 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. SE M. T es t Spurious Emission from 30MHz to 1GHz Test Mode: Transmitting-Low channel (5775MHz) Horizontal: No. Frequency Reading Correct Result Limit Margin (MHz) (dBm) Factor(dB) (dBm) (dBm) (dB) 1 105.2718 -87.47 17.40 -70.07 -54.00 -16.07 ERP 2 734.4913 -86.97 26.98 -59.99 -54.00 -5.99 ERP 3 875.2470 -87.16 28.42 -58.74 -36.00 -22.74 ERP REPORT NO.: STR15098069E-2 PAGE 14 OF 31 Remark RF REPORT Shenzhen SEM.Test Technology Co., Ltd. Frequency Reading Correct Result Limit Margin (MHz) (dBm) Factor(dB) (dBm) (dBm) (dB) 1 100.9340 -88.20 17.85 -70.35 -54.00 -16.35 ERP 2 739.6605 -87.62 27.29 -60.33 -54.00 -6.33 ERP 3 827.4934 -86.67 26.91 -59.76 -54.00 -5.76 ERP SE M. T No. es t Vertical: REPORT NO.: STR15098069E-2 PAGE 15 OF 31 Remark RF REPORT Shenzhen SEM.Test Technology Co., Ltd. SE M. T es t Test Mode: Transmitting-Middle channel (5805MHz) Horizontal: No. Frequency Reading Correct Result Limit Margin (MHz) (dBm) dB (dBm) (dBm) (dB) 1 106.0126 -88.06 17.32 -70.74 -54.00 -16.74 ERP 2 401.8385 -87.70 21.88 -65.82 -36.00 -29.82 ERP 3 734.4913 -86.89 26.98 -59.91 -54.00 -5.91 ERP REPORT NO.: STR15098069E-2 PAGE 16 OF 31 Remark RF REPORT Shenzhen SEM.Test Technology Co., Ltd. Frequency Reading Correct Result Limit Margin (MHz) (dBm) dB (dBm) (dBm) (dB) 1 99.5281 -88.82 17.83 -70.99 -54.00 -16.99 ERP 2 734.4913 -87.28 26.98 -60.30 -54.00 -6.30 ERP 3 893.8567 -86.84 28.55 -58.29 -36.00 -22.29 ERP SE M. T No. es t Vertical: REPORT NO.: STR15098069E-2 PAGE 17 OF 31 Remark RF REPORT Shenzhen SEM.Test Technology Co., Ltd. SE M. T es t Test Mode: Transmitting-High channel (5825MHz) Horizontal: No. Frequency Reading Correct Result Limit Margin (MHz) (dBm) dB (dBm) (dBm) (dB) 1 103.8055 -88.41 17.55 -70.86 -54.00 -16.86 ERP 2 750.1083 -86.91 26.87 -60.04 -54.00 -6.04 ERP 3 851.0353 -87.11 27.70 -59.41 -54.00 -5.41 ERP REPORT NO.: STR15098069E-2 PAGE 18 OF 31 Remark RF REPORT Shenzhen SEM.Test Technology Co., Ltd. Frequency Reading Correct Result Limit Margin (MHz) (dBm) dB (dBm) (dBm) (dB) 1 100.2286 -87.78 17.92 -69.86 -54.00 -15.86 ERP 2 734.4913 -86.52 26.98 -59.54 -54.00 -5.54 ERP 3 851.0353 -87.46 27.70 -59.76 -54.00 -5.76 ERP SE M. T No. es t Vertical: REPORT NO.: STR15098069E-2 PAGE 19 OF 31 Remark RF REPORT Shenzhen SEM.Test Technology Co., Ltd. Spurious Emission Above 1GHz Frequency Reading Correct Result Limit Margin Polar (MHz) (dBm) dB (dBm) (dBm) (dB) H/V Low Channel-5775MHz 11550 -51.43 3.1 -48.33 -30 -18.33 H 17325 -53.45 4.2 -49.25 -30 -19.25 H 11550 -51.27 3.1 -48.17 -30 -18.17 V 17325 -53.75 4.2 -49.55 -30 -19.55 V t Middle Channel-5805MHz -51.28 3.1 -48.18 -30 -18.18 H 17415 -52.73 4.5 -48.23 -30 -18.23 H 11610 -51.36 3.1 -48.26 -30 -18.26 V 17415 -55.53 4.5 -51.03 -30 -21.03 V -48.16 -30 -18.16 H -51.04 -30 -21.04 H -46.27 -30 -16.27 V -49.96 -30 -19.96 V es 11610 High Channel-5825MHz -51.26 3.1 17475 -55.54 4.5 11650 -49.37 3.1 17475 -54.46 4.5 SE M. T 11650 Note: Testing is carried out with frequency rang 30MHz to 40 GHz, which above 4th Harmonics are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. REPORT NO.: STR15098069E-2 PAGE 20 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 6. Duty Cycle 6.1 Applicable Standard SE M. T es t Test is conducting under the description of ETSI EN 300 440-1 section 7.4. Where an acknowledgement is required, the additional transmitter on-time shall be included and declared by the manufacturer. 6.2 Test Procedure Test is conducting under the description of ETSI EN 300 440-1 section 7.4.2. 6.3 Environmental Conditions Temperature: 22 °C Relative Humidity: 45% ATM Pressure: 1019 mbar 6.4 Summary of Test Results/Plots For generic use devices operating at frequency range 5725-5875MHz, according to ETSI EN 300 440-1, the duty cycle is no restriction. REPORT NO.: STR15098069E-2 PAGE 21 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. 7. Receiver Spurious Emissions 7.1 Limit of Spurious Emissions According to the ETSI EN 300 440-1 section 8.3.5, the power of any spurious emission shall not exceed 2 nW in the range 25 MHz to 1 GHz and shall not exceed 20 nW on frequencies above 1 GHz. 7.2 Test Procedure t The EUT was placed on a nonmetal table which is 1.5 meter above the grounded reference plane and set to work in receiving operation mode. For more detail please refer to the ETSI EN 300 440-1 section 8.3.4. The EUT was operating at normal to represent worst case during final qualification test. Temperature: 22 °C Relative Humidity: 45% ATM Pressure: 1019 mbar 7.4 Summary of Test Results/Plots es 7.3 Environmental Conditions SE M. T According to the data sheet, the EUT complied with the EN 300 440 standards, and had the worst margin of: -14.26 dB at 737.0714 MHz in the Vertical polarization, Receiving mode, 3Meters REPORT NO.: STR15098069E-2 PAGE 22 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. SE M. T es t Receiver Spurious Emission From 30MHz To 1GHz Test Mode: Receiving mode Horizontal: No. Frequency Reading Correct Result Limit Margin (MHz) (dBm) dB (dBm) (dBm) (dB) 1 43.6585 -71.77 -7.73 -79.50 -57.00 -22.50 ERP 2 56.3948 -71.04 -8.16 -79.20 -57.00 -22.20 ERP 3* 454.3100 -71.70 -2.11 -73.81 -57.00 -16.81 ERP REPORT NO.: STR15098069E-2 PAGE 23 OF 31 Remark RF REPORT Shenzhen SEM.Test Technology Co., Ltd. Frequency Reading Correct Result Limit Margin (MHz) (dBm) dB (dBm) (dBm) (dB) 1 330.1949 -83.22 6.80 -76.42 -57.00 -19.42 ERP 2 473.8347 -82.08 10.09 -71.99 -57.00 -14.99 ERP 3* 737.0714 -81.44 10.18 -71.26 -57.00 -14.26 ERP SE M. T No. es t Vertical Remark Note: Testing is carried out with frequency rang 30MHz to 10th Harmonics frequency, which above 1GHz are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. REPORT NO.: STR15098069E-2 PAGE 24 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. EXHIBIT 1 - PRODUCT LABELING t Proposed CE Label Format Proposed Label Location on EUT es Specifications: Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. The ‘CE’ marking must be affixed to the EUT or to its data plate. Where this is not possible or not warranted on account of the nature of the apparatus, it must be affixed to the packaging, if any, and to the accompanying documents. The ‘CE’ marking must have a height of at least 5 mm. If the ‘CE’ marking is reduced or enlarged the proportions given in the above graduated drawing must be respected. SE M. T CE Label Location REPORT NO.: STR15098069E-2 PAGE 25 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. EXHIBIT 2 - EUT PHOTOGRAPHS t EUT View 1 SE M. T WIFI 2.4G Antenna es WIFI 5G/5.8G Antenna EUT View 2 REPORT NO.: STR15098069E-2 PAGE 26 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. SE M. T es t EUT View 3 EUT View 4 REPORT NO.: STR15098069E-2 PAGE 27 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. SE M. T es t EUT View 5 EUT Housing and Board View 1 REPORT NO.: STR15098069E-2 PAGE 28 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. SE M. T es t EUT Housing and Board View 2 REPORT NO.: STR15098069E-2 PAGE 29 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. EXHIBIT 3 - TEST SETUP PHOTOGRAPHS SE M. T es t Spurious Emission Test Setup (Below 1GHz) Spurious Emission Test Setup (Above 1GHz) REPORT NO.: STR15098069E-2 PAGE 30 OF 31 RF REPORT Shenzhen SEM.Test Technology Co., Ltd. SE M. T es t Extreme Conditions Test Setup ***** END OF REPORT ***** REPORT NO.: STR15098069E-2 PAGE 31 OF 31 RF REPORT
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2015:10:08 14:14:21+08:00 Create Date : 2015:10:08 14:13:41+08:00 Metadata Date : 2015:10:08 14:14:21+08:00 Format : application/pdf Title : Microsoft Word - EN 300440 Creator : Administrator Document ID : uuid:ad37e71c-e325-4cc1-8b88-1520fa1d0f3e Instance ID : uuid:201889ef-dec2-467d-aa50-4cac490bd8dc Page Count : 31 Author : AdministratorEXIF Metadata provided by EXIF.tools