GE Washer Compact WSLP1500 WSLS1500 31 9189
2013-04-09
: Pdf Ge - Washer - Compact - Wslp1500 - Wsls1500 - 31-9189 GE - Washer - Compact - WSLP1500 - WSLS1500 - 31-9189 GE, Camco, Hotpoint, Mofat
Open the PDF directly: View PDF 
.
Page Count: 37
| Download | |
| Open PDF In Browser | View PDF |
GE Consumer & Industrial Technical Service Guide SEPTEMBER 2009 GE Compact Washer TEMP START LOAD OPTIONS PAUSE ULTRA CLEAN CYCLES WSLP1500J WSLS1500J 31-9189 GE Appliances General Electric Company Louisville, Kentucky 40225 POWER IMPORTANT SAFETY NOTICE The information in this service guide is intended for use by individuals possessing adequate backgrounds of electrical, electronic, and mechanical experience. Any attempt to repair a major ap pli ance may result in personal injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use. WARNING To avoid personal injury, disconnect power before servicing this prod uct . If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. RECONNECT ALL GROUNDING DEVICES If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened. GE Consumer & Industrial Technical Service Guide Copyright © 2009 All rights reserved. This service guide may not be reproduced in whole or in part in any form without written permission from the General Electric Company. –2– Table of Contents Back Cover ...........................................................................................................................................................................19 Brake Control Motor ........................................................................................................................................................32 Circuit Board Connections ............................................................................................................................................17 Component Locator Views ...........................................................................................................................................15 Control Features ................................................................................................................................................................ 9 Control Panel and PCB ................................................................................................................................................18 Dispenser Assembly ........................................................................................................................................................25 Drain Pump .........................................................................................................................................................................25 Error Codes ..........................................................................................................................................................................34 Fuse .........................................................................................................................................................................................24 Installation ........................................................................................................................................................................... 6 Introduction ......................................................................................................................................................................... 5 Lid Switch and Harness .................................................................................................................................................23 Nomenclature .................................................................................................................................................................... 4 Outer Tub and Suspension Assembly .....................................................................................................................29 Pressure Sensor .................................................................................................................................................................21 Schematic.............................................................................................................................................................................36 Service Test Mode.............................................................................................................................................................35 Shaft Assembly ..................................................................................................................................................................33 Shaft Assembly and Brake Overview .....................................................................................................................31 Special Features ................................................................................................................................................................ 8 Top Cover..............................................................................................................................................................................24 Troubleshooting ................................................................................................................................................................34 Unbalance Switch.............................................................................................................................................................22 Warranty .............................................................................................................................................................................37 Wash Basket .......................................................................................................................................................................28 Washer Components ......................................................................................................................................................18 Washing Motor and Belt................................................................................................................................................27 Water Valve .........................................................................................................................................................................20 –3– Nomenclature Model Number W S L S 1 5 0 0 J W W Brand W = GE Washer Color WW = White Feature Package S = Unitized Compact Engineering Revision Model Year F - 2005 G - 2006 H - 2007 J - 2008 K - 2009 Capacity/Configuration L = Large Control Platform S = Stationary Voltage 0 = US Voltage Nomenclature Serial Number The first two numbers of the serial number identify the month and year of manufacture. Example: AS123456S = January, 2009 Mini-Manual A - JAN D - FEB F - MAR G - APR H - MAY L - JUN M - JUL R - AUG S - SEP T - OCT V - NOV Z - DEC 2009 - S 2008 - R 2007 - M 2006 - L 2005 - H 2004 - G 2003 - F 2002 - D 2001 - A 2000 - Z 1999 - V 1998 - T The letter designating the year repeats every 12 years. Example: T - 1974 T - 1986 T - 1998 The nomenclature plate is located on the back below the top cover. The mini-manual is placed in an envelope located under the control panel. –4– Introduction The new GE Compact Washer has the following features: • Electronic One-Touch Controls with LED readout simplify cycle selection and provide accurate cycle times. • One-Touch Loading Sensing eliminates guesswork and helps reduce water waste. • Ten wash cycles provide a setting for almost every load, from heavy cottons to casual synthetics; includes settings for light- to heavy-soil regular, whites, colors, casual and delicate fabrics. • Three wash/rinse temperatures ― A variety of temperatures provides great wash results and longer fabric life. • Four water levels match the water level to each load to reduce water waste per cycle. • One Wash/Spin Speed ― Provides reliable cleaning performance for regular clothes. • Custom Wash Cycle ― Saves a favorite cycle for future use. • Dispenser adds diluted detergent and fabric softener at the correct time during the wash or rinse cycles. • Overflow Protection ― Activates the drain pump whenever water reaches overflow level during a temporary stop, waiting action, or spin action. Overflow also sensed 3 times during a wash or rinse cycle. • Built-in Status indicators display certain associated error codes. • The wash tub is constructed of durable stainless steel. • UV stabilizers are utilized on the control panel, top cover, and lid to prevent yellowing when exposed to sunlight. –5– Installation Location • Washer must be installed on firm flooring. Concrete flooring is best, but wood base is sufficient, providing floor support meets FHA standards. • Washer should not be installed on rugs or exposed to the weather. • Install or store washer where it will not be exposed to temperatures below freezing. • Minimum clearances between washer and adjacent walls or other surfaces are: 2” either side, 2” front, and 3” rear. • Minimum vertical space from floor to overhead shelves, cabinets, ceilings, etc., is 96”. • Closet doors must be louvered or otherwise ventilated and have at least 60 square inches open area for washer only, or if the closet contains both a washer and dryer, doors must contain at least 120 square inches of open area, equally distributed. 60 sq. in. (387.1 sq. cm 60 sq. in. (387.1 sq. cm Closet door Note: The clearances stated are minimums. Consideration must be given to providing adequate clearances for installation and servicing. Cable Tie Cable Tie Cable Tie g Stand Pipe Laundry Tub GEA00044 GEA00045 Plumbing • Water pressure must be 10 psi minimum to 150 psi maximum dynamic pressure measured at faucet. • Water temperature on household water heater should be set to deliver water at 120° to 150°F (50° to 66°C) in the washer when HOT wash is selected. • Shut-off valves should be supplied for both hot and cold water lines. • Drain water into a standpipe or laundry tub. The discharge height must not be less than 30” nor more than 8’ above the base of the washer. The standpipe must be 1½” minimum inside diameter and must be open to the atmosphere. (Continued next page) –6– Electrical Wiring • National Electrical Codes or prevailing local codes and ordinances must be followed. • 120V, 60Hz must be supplied and connected to an individual, properly grounded branch circuit, protected by a 15- or 20-amp circuit breaker or time delay fuse. • Wiring must be 2-wire with ground. Electrical Rating Voltage AC......................................................120 Hertz ...................................................................60 Total connected load amperage ........10.0 For use on adequately wired 120-volt, 15-amp circuit having 2-wire service with a separate ground wire. This appliance must be grounded for safe operation. Leveling the Washer Excessive vibration will occur if the washer is not leveled. This will also trip the unbalance switch and stop the washer. Check to ensure the washer is level. With the door open, the spin basket should be centered in the opening as shown in the “leveled” view. If the spin basket is not in the center or “unleveled” as shown at far right, level the washer as follows: Leveled Note: Be careful not to kick or step on the leveling locks. • Pull out the leveling locks located at the bottom front of the left and right sides of the washer. This releases the spring loaded leveling feet. • The washer will attempt to automatically level itself. • Check level at body panel line and adjust as necessary. • Push leveling locks back in. • Manually level the rear feet (side to side). Unleveled GEA00042 –7– Special Features Before starting the washer: • Load the laundry in the washer. • Add the detergent and fabric softener to the dispenser drawer. Detergent and Fabric Softener Dispenser Drawer Maximum Fill Tower The detergent and fabric softener dispensers will automatically release their contents at the proper time during the cycle. To Use the Detergent Dispenser: Add measured detergent to the dispenser. Make sure detergent is spread evenly and is level. To Use the Fabric Softener Dispenser: Use only liquid fabric softener. Pour into dispenser, using amount recommended on package. Do not fill any higher than the top of the maximum fill tower. Never pour fabric softener directly on clothes. It may stain them. Cleaning the Detergent and Fabric Softener Dispenser Drawer 1. Remove the drawer by opening it fully then tilting the front of the door up. Pull out. 2. Rinse the drawer with water. If necessary use a soft cloth to wipe off any debris. 3. Line up the drawer with the opening and push the dispenser drawer straight in. Lint Filter Clean the lint filter inside the wall of the wash basket once a week for best filtering results. To remove: Press the tab at the top of the filter and pull out. To clean: Open the filter. Clean the filter with a toothbrush. –8– Control Features About the control and indicator settings. COLD HOT WARM TEMP EXTRA LARGE LARGE MEDIUM SMALL EXTRA SMALL SOAK WASH HEAVY DUTY RINSE SPIN LOCK LOAD HOLD 3 SECS TO LOCK/UNLOCK EST. MINUTES REMAINING LOAD SENSING COLORS WHITES DELICATES SPEED WASH CUSTOM CYCLE POWER START ULTRA CLEAN CONTROLS PAUSE H DELAY WURAS S 1 to 18 HO CYCLES OPTIONS Before starting the washer: • Load the laundry in the washer. • Add the detergent and fabric softener to the dispenser drawer. START PAUSE To Use Automatic One-Touch Washing The LOAD SENSING feature automatically senses the size of your load, tub fills with the appropriate amount of water, and calculates the amount of wash time required to complete the cycle. NOTE: When using the LOAD SENSING feature, it is normal for the pulsator to rotate before water fills in the tub. • To choose the automatic LOAD SENSING feature, press POWER ON/OFF. LOAD SENSING is the default water setting. Manually selecting a load size cancels LOAD SENSING. • Select the desired CYCLE, OPTION and water TEMP setting. • Then press START/PAUSE. • The COLORS indicator light will light up automatically unless you have selected one of the other LOAD SENSING cycles such as WHITES, DELICATES, SPEED WASH, CUSTOM CYCLE or ULTRA CLEAN. • Then simply press START/PAUSE. NOTE: When the cycle is operating, the OPTIONS LED flashes. When the washer is in PAUSE, the LED does not flash. –9– (Continued Next Page) To Choose Your Own Cycle Selections POWER ON/OFF 1 Press the POWER ON/OFF button to turn on the control panel. WASH OPTIONS 2 Choose the wash options you would like to include in the cycle. Press the WASH OPTIONS button until all the options you want to include are lit. More than one option can be selected. Soak+Wash +Rinse+Spin Soak+Wash+Heavy Duty+Rinse+Spin COLORS X X X X WHITES X X X DELICATES X X X SPEED WASH X X X X Cycle CUSTOM CYCLE ULTRA CLEAN Wash+Rinse Wash+Heavy Wash +Spin Duty+Rinse+Spin +Rinse Rinse +Spin Wash Only Rinse Only Spin Only X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X LOAD SIZE 3 The water level should just cover the clothes. Adjust the load size accordingly. Loosely load clothes no higher than the top row of holes in the washer basket. WASH CYCLE 4 These wash cycles control the length of the washing process. The chart on the following page will help match the WASH CYCLE setting to your specific laundry needs. When a cycle is selected, the automatic temperature that the machine defaults to can be changed to whatever temperature you desire. – 10 – (Continued next page) The control can add an additional 4 wash cycles to each washing process. Each additional wash cycle adds approximately 16 minutes. To add additional wash cycles: • Select a cycle using Automatic One-Touch Washing. • Press the START/PAUSE pad. • Anytime after the START pad is pressed, if the OPTIONS pad is pressed, the display will show 1. • Pressing the OPTIONS pad again will change the display to 2. Selections from 1 to 5 are available. NOTE: Once a selection is made, the control will automatically add additional time to the Est Minutes Remaining display. 1 is the normal wash cycle without additional time added. When the SPIN (only) option is selected, spin cycle time can be adjusted by pressing the OPTIONS pad after the cycle has started. The display will show the actual minutes remaining in any SPIN (only) cycle. Colors For easy care and wrinkle-resistant items. Whites For heavy to lightly soiled cotton, household linens, towels, work and play clothes. Delicates For lingerie and delicate fabrics with light to normal soils. Speed For one or two lightly soiled items Wash that are needed quickly. Custom Manually selected options of water temperature and wash options saved for future uses. (See NOTE 1.) Ultra Maximizes detergent efficiency by adding Clean water in steps and slowly diluting the detergent to the standard level. (See NOTE 2.) Default Wash/Rinse Temperatures WARM/COLD HOT/COLD COLD/COLD WARM/COLD WARM/COLD WARM/COLD NOTE 1. To use CUSTOM CYCLE, set the CYCLES selection to CUSTOM CYCLE. Select TEMP and OPTIONS choices. Press START/PAUSE pad. Control remembers, and the next time CUSTOM CYCLE is selected, the most recent settings will be displayed. CUSTOM CYCLE always utilizes LOAD SENSING. Load size cannot be locked in. NOTE 2. The washer partially fills, (approximately 75%) then begins to agitate for approximately 30 seconds. The washer will then pause and continue to fill for about 10 seconds, then agitate. It repeats this process, in varying degrees and stages, 4 times before the tub is at the correct water level and the machine completes the wash cycle. – 11 – (Continued Next Page) Time-Table of Function 1. Twenty minute SOAK function occurs only when selected. This time has not been added to the ALL TIME column. 2. When one or more additional rinse cycles are selected, this shorter ADDITIONAL RINSE SPIN time is used for all rinse cycles except the final rinse cycle. The final rinse cycle uses the FINAL SPIN time. The time from this ADDITIONAL RINSE SPIN column has not been added to the ALL TIME column. 3. The actual fill time is a function of water flow rate and may be more or less than the time specified. If more time is needed, the countdown will pause. If less time is needed, the control deletes the remaining fill time. 4. The rinse water valve flushes fabric softener from dispenser for 75 seconds ((10’ on / 5’ off) -5 times) at the beginning of the last rinse cycle only. – 12 – (Continued Next Page) About the control lock. The control lock feature only locks the control during a cycle. Control lock does not lock the control in the standby mode. To activate control lock, press and hold LOAD and OPTIONS pads simultaneously for 3 seconds while the washer is in a cycle. The display will alternate between CL and time remaining. – 13 – (Continued Next Page) Water System and Filtering Weight Recognition Function (Load Sensing) • The weight recognition function measures the washing load before water is supplied. • The weight recognition function is canceled when water level key is pressed prior to the completion of weight recognition function. • If the current water level is above the lowest level at the beginning of weight sensing, it is automatically set as a high level. • If you change wash cycle after sensing weight, the high water level is automatically selected regardless of the water level decided by the sensing of weight. Water Supply Function • Relations between water level, frequency, and water supply capacity are as follows: Water Level Frequency Chart LEVEL EMPTY EXTRA SMALL SMALL MEDIUM LARGE EXTRA LARGE • GALLONS 0 8.00 10.6 12.4 13.2 19.6 FREQUENCY (kHz) 25.2 24.1 23.43 23.03 22.80 22.13 If the water level does not reach the selected level within 60 minutes after starting water supply, the Water Supply Error (7E) is displayed. Supplementary water supply is performed during every washing or rinsing operation. The steps are as follows: • Supply water to the water level selected. • Perform the ACTIVATE operation for 1.5 minutes. • Sense the present water level after stopping motor. • Compare the present water level to the water level selected. • If present water level is less than the water level selected, supply water to the water level selected. If present water level is greater than the water level selected, continue the washing or rinsing operation. • Total time of supplementary water supplying is not over 30 seconds. – 14 – Component Locator Views Top View Lint Filter 304 Stainless Steel Wash Basket Pulsator Tub Cover Water Valve Assembly Fuse Pressure Sensor Unbalance Switch Water Inlet Ports – 15 – (Continued Next Page) Component Locator Views (Con't) Rear View Pressure Sensor Hose Drain Hose Connector Suspension Rod Tub Outlet Hose Belt Drain Pump Pump Cleanout Dispenser Drawer – 16 – Circuit Board Connections PCB (Printed Circuit Board) CN4 (WHT) CN5 (RED) CN2 (BLK) CN1 CN3 CN1 - Door Switch, Unbalance Switch, Pressure Sensor CN2 - Line Voltage CN3 - Neutral, Neutral to Water Valve Solenoids CN4 - Washing Motor CN5 - Washing Motor, Washing Motor Condenser CN6 - Water Valve Solenoids, Brake Control Motor, Drain Pump Motor – 17 – CN6 Washer Components 3. Remove the 2 Phillips-head screws that attach the control panel to the top cover. Control Panel and PCB The control panel is located on the front of the top cover. The control panel consists of an LED display, and an 8 push-button keypad that operates a printed circuit board (PCB). Note: In the following step, 9 tabs located inside the control panel are engaged in 9 corresponding slots in the top cover. Control Panel Removed from Top Cover The PCB is supplied with 120 VAC at PCB locations CN2 pin 1 to CN3 pin 2. A 12-amp fuse is installed in the white neutral line and is located under the rear cover. (See Fuse.) CN3 CN2 WARNING: Sharp edges may be exposed when servicing washer. Use caution to avoid injury and wear Kevlar gloves or equivalent protection. To remove the control panel and PCB: The control panel is attached to the top cover with 2 recessed Phillips-head screws (1 on each side). It is necessary to remove 2 screw covers to access the screws. 4. Slide the control panel to the left, then lift the panel from the top cover. 1. Open the lid. 2. In the notch provided, insert a straightened paper clip or small flat blade screwdriver, then pry and lift the 2 screw covers (1 on each side), from the top of the control panel. Caution: To prevent damage to the control panel, place a cloth or towel over the front of the top cover. 5. Place the control panel face down on the protected top cover. Screw Cover Notch – 18 – (Continued next page) 6. Remove the 5 Phillips-head screws that attach the PCB to the control panel. Place the control panel and the cloth or towel aside. Back Cover Removal of the back cover provides access to the water valve, pressure sensor, unbalance switch, fuse, and lid springs. The back cover is held to the rear of the top cover with 2 Phillips-head screws and 4 tabs. The tabs are located inside the back cover. After removal of the screws, the back cover can be lifted straight up. BACK COVER TOP COVER 7. Place the PCB wiring side up and note the wiring locations and routing, then disconnect the wiring from the PCB. Caution: • To prevent misalignment of the control panel selector buttons to the PCB, when installing the PCB to the control panel route the wiring as shown below. • Make sure all screw locations on the PCB fully contact the control panel before installing the screws. • Before reapplying power, check for proper button operation, press each button and listen for an audible click. • When installing the control panel to the top cover, before sliding the panel toward the right, make sure all panel tabs are engaged with slots in the cover. – 19 – The water valve is located at the rear center of the top cover. Water Valve The water valve consists of a valve body and 3 solenoid coils. It is only available as a complete assembly. Each solenoid controls a specific water function. To remove the water valve: 1. Remove the back cover. (See Back Cover.) 2. Remove the 3 Phillips-head screws and lift the valve cover from the valve. • Each coil on the water valve assembly has an approximate resistance value of 1.2K Ω. • The water valves receive power from the PCB. • When energized, there should be approximately 120 VAC at the appropriate coil. VALVE COVER CN6 3. Disconnect the 3 wire harnesses from the valve. CN6 CN6 CN3 Rinse Water Hot Water Cool Water 4. Lift the water valve straight up and remove the valve from the top cover. – 20 – Pressure Sensor Test Pressure Sensor The pressure sensor is connected by a clear hose to an air reservoir near the bottom of the outer tub and operates by a frequency (kHz) signal to the inverter board. If the pressure sensor is not operating correctly, perform the following test: Operate the washer on the spin cycle until all remaining water is drained from the washer. The pressure sensor wires (violet, orange, and pink) are connected at pins 1, 2, and 3 at CN1 on the PCB. (See Circuit Board Connections.) Clear the pressure switch air tube of any obstructions such as lint, detergent or fabric softener deposits, or foreign objects. The approximate resistance value of the transducer, measured between the pink and violet wires, is approximately 23 Ω. Check the approximate water levels at each load selection. Water levels are measured from the bottom of the wash basket: EXTRA SMALL - 5 ½ inches SMALL - 6 ¾ inches MEDIUM - 7 ½ inches LARGE - 8 ¾ inches EXTRA LARGE - 11 ¾ inches When the water level rises in the washer tub, air is trapped in the reservoir. As the water level rises, the air pressure in the reservoir increases. • The pressure is translated into an electrical signal (frequency) by the pressure sensor. • The frequency will vary from approximately 27 kHz (empty tub) to 22 kHz (full tub). • This frequency can be measured at the pressure sensor between the orange and violet wires. CN1 LEVEL EMPTY EXTRA SMALL SMALL MEDIUM LARGE EXTRA LARGE GALLONS 0 8.00 10.6 12.4 13.2 19.6 FREQUENCY (kHz) 25.2 24.1 23.43 23.03 22.80 22.13 Extra Small Water Level Shown The frequency is monitored by the PCB, which turns off the water valves when the desired water level is achieved. Note: The water level will vary slightly depending on the load size, which is measured by the weight recognition function and any supplementary water needed. This information is sent to the PCB, which then determines the appropriate water level. – 21 – (Continued next page) The pressure sensor is located on the top cover, left of the water valve. Unbalance Switch To remove the pressure sensor: Note: Before disconnecting the hose from the pressure sensor, be sure the water level is below the bottom of the spin basket. 1. Remove the back cover. (See Back Cover.) 2. Disconnect the pressure sensor wire harness. The unbalance switch is located at the right rear corner of the top cover. The switch actuator is inserted through a hole in the top cover. The normally open contacts will close when the lid is closed. With the lid closed, the contacts will momentarily open when an out of balance load allows the outer tub to push the actuator approximately 3/4-inch toward the rear of the cabinet. The first two times the switch is tripped, the washer stops, time is added to the display, tub fills with water, agitates, then spins again. If the switch is tripped a third time, Ub will appear in the display. With Ub displayed, the lid will need to be opened, the clothing redistributed, and START selected to complete the cycle. Disconnect The continuity of the switch can be checked at the switch terminals or at the PCB location, CN1 pin 4 and pin 11. 3. Carefully push both hooks slightly outward, then lift the pressure sensor. An open unbalance switch will: Hook • Cause Lo, lid open, to appear in the display • Not stop the fill function • Stop the wash cycle • Stop the drain pump • Stop the spin cycle • Not stop the drain pump operating during overflow protection. Hook 4. Using pliers, squeeze the clamp and pull the air tube off the pressure sensor. Clamp Air Tube CN1 Note: Lo, lid open, shown in the display can be caused by an open lid switch or open unbalance switch. Test each switch separately to determine which one is at fault. The unbalance switch and actuator are replaced as an assembly. – 22 – (Continued next page) To remove the unbalance switch: 1. Remove the back cover. (See Back Cover.) 2. Disconnect the 2 wires from the switch. Lid Switch and Harness When the lid is in the closed position, a magnet located inside the front half of the lid will activate and close the lid switch contacts. 3. Remove the 2 Phillips-head screws that attach the switch to the top cover. Unbalance Switch Magnet Disconnect Disconnect An open lid switch affects washer operation the same as an open unbalance switch. (See Unbalance Switch.) 4. Lift and remove the unbalance switch from the washer. Note: Lo, lid open, shown in the display can be caused by an open lid switch or open unbalance switch. Test each switch separately to determine which one is at fault. CN1 The lid switch is attached to the inside of the top cover with 2 Phillips-head screws. The top cover must be lifted to access the lid switch. (See Top Cover.) Actuator Lid Switch Note: When replacing the lid switch, note the routing of the wire harness. – 23 – Fuse Top Cover The washer utilizes a fuse connected in the neutral line of the top cover wire harness. The fuse is rated at 250 VAC and 12 amps. The fuse and fuse holder are located at the right rear corner of the top cover. To remove the top cover: To remove the fuse: 2. Remove the 2 Phillips-head screws that attach the front of the top cover to the cabinet. 1. Remove the control panel and PCB. (See Control Panel and PCB.) 1. Remove the back cover. (See Back Cover.) 2. Lift the fuse holder from the recess in the top cover. Fuse Holder 3. Remove the back cover. (See Back Cover.) 4. Remove the foam tape. Recess Note: In the following step, 2 wire harnesses are located inside the wire harness cover. 5. Unwrap the electrical tape and remove the wire harness cover. 3. Disengage the latch from the tab and open the fuse holder. 6. Disconnect the 2 wire harnesses. Harness Cover Electrical Tape Tab Foam Tape Latch 7. Remove the pressure sensor and air tube clamp. (See Pressure Sensor.) 8. Remove the Phillips-head screw that attaches the ground wire to the cabinet. 4. Remove fuse from fuse clips. Ground Wire Clip Clip 9. Lift the top cover from the cabinet. – 24 – Dispenser Assembly Drain Pump The dispenser assembly provides automatic dispensing of detergent and fabric softener as long as the user fills the compartments prior to starting the washer. The pump consists of a 120-VAC, 60-Hz motor, impeller, impeller housing, and a removable strainer that helps prevent foreign objects from entering the pump impeller and drain outlet. The products added to the dispenser are diluted with water before they are dispensed into the wash basket. This is controlled by the PCB. • The pump runs whenever the washer is in the spin function of a cycle. • The drain pump runs if water reaches overflow level and the washer is plugged in. • The pump is capable of eliminating 4 gallons (15 liters) per minute. • Recommended minimum standpipe diameter is 1 ½ inches. • Standpipe maximum height is 96 inches, measured from the floor at the washer location. • The pump motor has an approximate resistance value of 11.8 Ω. Each of the 3 water valve solenoids is controlled by the PCB to release at the right time during the wash and rinse cycles. Water released to dilute detergent passes through a guide that evenly distributes water into the detergent reservoir. Water released in the final rinse cycle flows directly into the fabric softener reservoir. To remove the dispenser assembly: 1. Open the lid and pull the dispenser drawer out to the stop position. 2. Tilt the front of the drawer up and pull it out of the dispenser cavity. CN3 CN6 The drain pump is located inside the left rear corner of the washer. To clean the impeller and impeller housing: 3. Remove the Phillips-head screw that attaches the guide to the top of the cavity. WARNING: The drain pump is not grounded. To avoid electric shock, unplug the unit before servicing. Note: The impeller can be accessed for cleaning without removing the drain hoses. Under normal conditions, approximately 1 quart of water will drain out when the pump cleanout is removed. Use care to avoid water spills. 1. Disconnect power to the machine. 4. Slide the guide out of the cavity. 2. Place a shallow pan under the drain cleanout. 3. Turn the pump cleanout counterclockwise approximately 2 turns, then pull outward. 4. Remove any debris or foreign objects from the strainer and interior of the pump before reinstalling. – 25 – (Continued next page) To remove the drain pump: Note: In the following step, the tub outlet hose is difficult to remove due to a sealing compound used at the factory. 1. Remove the 2 Phillips-head screws and the access panel from the back of the washer. a. Squeeze the clamp and slide it back. 2. Drain any remaining water from the washer. (See To clean the impeller and impeller housing, this section.) 3. Remove the 2 Phillips-head screws, located below the cleanout, that attach the pump to the back of the cabinet. b. Carefully break the tub outlet hose loose by inserting a small flat-blade screwdriver under the hose to break the seal. c. Remove the hose. 5. Remove the 3 hoses from the pump. Pump Cleanout Caution: To remove the drain pump, the washer must be carefully placed on its front or side. To prevent scratches to the surface of the washer, place a towel or blanket on the floor. 4. Remove the 3 Phillips-head screws that attach the pump to the bottom of the washer base. 6. Remove the Phillips-head screw and the pump cover from the pump. Pump Cover – 26 – (Continued Next Page) Note: The electrical terminal ends, which attach to the drain pump, have locking tabs on them. These tabs cannot be seen because they are encased in plastic. To remove these terminals, grasp the releasing locking tab of the terminal with needlenose pliers. Gently squeeze the pliers' jaws together while pulling the electrical terminal from the drain pump. Washing Motor and Belt The motor assembly consists of a reversible, AC motor. The motor drives the shaft assembly pulley with a V-belt. On the motor plug, check for approximate resistance values: Blue to white and yellow - 5.5 Ω Red to white and yellow - 5.5 Ω ELECTRICAL TERMINAL RELEASE/LOCKING TAB SHOWN WITH PLASTIC COVERING REMOVED ELECTRICAL TERMINAL RELEASE/LOCKING TAB Blue to red - 11 Ω (Can also be measured at PCB CN4 to CN5.) 7. Disconnect the 2 wires from the pump. CN4 CN5 CN3 Disconnect Caution: If the outer tub is not removed as an assembly, to access the belt, the washer can be carefully placed on its front or side. To prevent scratches to the surface of the washer, place a towel or blanket on the floor. Disconnect Caution: To ensure there is no water leakage, care must to taken when reinstalling and sealing the hoses to the drain pump. When installing, apply a thin coat of sealing compound (part no. WH60X15) to the inner surface of the drain hoses. The washing motor is attached to the platform with two 13-mm bolts. To replace it requires removing the belt, two 13-mm (33/64” SAE equivalent) bolts, and the Phillips-head screw that attaches the motor wire harness to the platform. The motor can then be lifted from the platform. To remove the washing motor and belt: 1. Loosen the two 13-mm bolts that attach the washing motor to the platform, then slide the motor toward the shaft assembly. 2. Rotate the belt off the motor and shaft assembly pulleys. – 27 – (Continued next page) 3. Remove the two 13-mm bolts from the motor. Wash Basket 4. Remove the Phillips-head screw that attaches the motor wire harness to the platform. The wash basket is contained inside the outer tub. The wash basket is rotated by a belt-driven shaft assembly. A 36-mm (17/16-in. SAE equivalent) nut attaches the wash basket to the shaft. To remove the wash basket: 1. Drain the washer using the pump cleanout. (See Drain Pump.) 2. Remove the top cover. (See Top Cover.) 3. Remove the 4 Phillips-head screws that attach the tub cover to the outer tub. Remove the cover. *Motor Condenser 5. Lift the motor, then place it harness-side up on the platform. 6. Disconnect the wire harness from the motor. Disconnect 7. Remove the 13-mm hex-nut that attaches the motor pulley to the motor shaft. * The washing motor utilizes a 42 μF condenser. The condenser is a start capacitor. If the condenser is open; the motor will hum, but not start. The condenser is attached to the platform with 2 Phillips-head screws. (For location of condenser, see photo after step 4.) Two wires are connected to the condenser. – 28 – (Continued next page) 4. Place a flat blade screwdriver in the slot under the pulsator cap. Gently pry up and remove the pulsator cap. Outer Tub and Suspension Assembly The wash basket, outer tub, motor, and shaft assembly are suspended by four rod and spring assemblies. The rod and spring assemblies are attached to each corner of the washer cabinet. They extend down and connect to the bottom of the outer tub. Pulsator Cap Suspension Rod 5. Remove the 10-mm (13/32” SAE equivalent) bolt that attaches the pulsator assembly to the shaft. To remove the outer tub: WARNING: The outer tub assembly is heavy and requires two people to remove it from the washer housing. Care should be taken when removing and installing the outer tub assembly. 1. Remove the top cover. (See Top Cover.) 6. Pull the pulsator assembly up and out. 7. Remove the 36-mm hex-head nut (loosen counterclockwise), and wave washer that attach the wash basket to the shaft. 2. Remove the 2 Phillips-head screws and the access panel from the back of the washer 3. Disconnect the 2 wires from the drain pump. 4. Remove the Phillips-head screw and the ground wire from the cabinet. 5. Compress and release the tabs on the 5 wire retainers attached to the back of the cabinet. Note: Water will remain in hoses even when the tub appears empty. Use care to avoid water spills. 36-mm Nut Washer (Under Nut) 6. Remove the tub outlet and tub overflow hoses from the outer tub: a. Cut the plastic clamp and remove it. b. Carefully break the hose loose. c. Remove the hose. 8. Lift the wash basket out of the outer tub. – 29 – (Continued Next Page) 7. Lift the outer tub up and disengage the suspension rod assemblies from each corner of the outer tub. Suspension Rod 8. Pull the outer tub assembly out of the washer cabinet. Caution: To ensure there is no water leakage, care must to taken when reinstalling and sealing the hoses to the outer tub. Note: Factory installed plastic hose clamps are nonreusable. When installing an outer tub assembly, replace the plastic clamps with new screw-type hose clamps provided with the new part. The screwtype hose clamps are also available separately. Clamp Part Number WD01X10322 WD01X10323 WD01X10324 Size 15/16" to 1½" 13/16" to 1¾" 1/2" to 29/32" – 30 – Shaft Assembly and Brake Overview The shaft assembly consists of the pulsator shaft, wash basket hub, and a brake system. The shaft assembly operates in 2 distinct modes, spin and agitation. The pulsator shaft transfers power to the wash system. Motor power is transmitted to the pulsator shaft from the drive belt to the drive pulley. The drive pulley is attached to one end of the pulsator shaft and the pulsator is attached to the other. The wash basket hub is fixed to the washer basket at all times. Brake action is applied to the wash basket hub located inside the shaft assembly and to a gear located at the bottom of the assembly. The brake motor extends or retracts a cable connected to the brake arm with a brake link. The position of the brake arm operates the brake that changes the shaft assembly mode from spin to agitation. In agitation mode, the wash basket hub is fixed to the platform and the pulsator shaft rotates when driven by motor. In spin mode, the pulsator shaft is fixed to the hub and both rotate together. Agitation Mode - No 120 VAC applied to brake motor. Brake cable extended and brake system engaged. Hub Brake Engaged Brake Link Brake Cable Brake Arm Engaged Position Gear Brake Engaged Brake Motor Spin Mode - 120 VAC applied to brake motor. Brake cable retracted and brake system disengaged. Hub Brake Disengaged Brake Link Brake Cable Brake Arm Disengaged Position Brake Motor Gear Brake Disengaged – 31 – To remove the brake control motor: Brake Control Motor 1. Pull out the pin, then remove the brake link from the shaft assembly brake lever. During a normal spin mode that is not interrupted, the basket will coast to a slow stop without the use of the brake control motor. 2. Remove the brake link from the cable. However, if the lid is opened during a spin cycle, the 120 VAC to the brake control motor is stopped, the gear engaged, and the basket stops immediately. 3. Disconnect the brake control motor wire harness. Diagnostic tip: The brake control motor and pump are always energized at the same time. Therefore, if the pump is running, the board is working properly and supplying 120 VAC to the brake control. An open brake control motor will allow the pulsator to turn during spin, but the basket will remain stationary. This will result in wet clothes at the end of the cycle. 4. Remove the 2 Phillips-head screws that attach the brake control motor to the platform. Pin Brake Link Cable Caution: To access the brake control motor, the washer can be carefully placed on its front or side. To prevent scratches to the surface of the washer, place a towel or blanket on the floor. Disconnect The brake control motor has an approximate resistance value of 1.4K Ω. CN3 Note: To prevent the brake cable from dislodging from the brake link, ensure brake link is installed with cable stop cutout facing away from the platform. CN6 The brake control motor is attached to the platform with 2 Phillips-head screws. Cable Stop Cutout – 32 – 3. Remove the belt. (See Washing Motor and Belt.) Shaft Assembly 4. Remove the pin and brake link from the shaft assembly. Manual Shaft Assembly Checks: • • To manually check activation, unplug washer and turn the drive pulley to the right. The activator should easily turn in the same direction at a ratio of 5.33:1. Turn the pulley to the left; the activator should easily turn in that direction. Pin To check spin, manually move the brake lever toward the brake motor to release brake and engage clutch. Rotate pulley to the right; tub should rotate to the right. Brake Link Brake Link Pin Note: Failure to operate as described requires shaft assembly replacement. The shaft assembly is attached to the platform with four 13-mm (33/64” SAE equivalent) bolts. To replace it requires removing the wash basket, belt, and support saddle. 5. Remove the four 13-mm bolts that attach the shaft assembly to the platform. To remove the shaft assembly: 1. Remove the wash basket. (See Wash Basket.) Caution: If the outer tub is not removed as an assembly, to access the shaft assembly, the washer can be carefully placed on its front or side. To prevent scratches to the surface of the washer, place a towel or blanket on the floor. 2. Remove the four 10-mm (13/32” SAE equivalent) bolts that attach the support saddle to the platform. 6. Lift the shaft assembly off the platform. – 33 – Troubleshooting Error Codes NOTE: It’s important to note error codes should only be used to help identify components which require testing. Never replace a part based solely on an error code. The control can generate a false error if the right conditions exist. Use the code only as a reference and always check the component before replacing. Error Water Level Sensor error : “1E ” Water Supply error : “FF ” Drain Pump error : “dr ” Lid Open error : “L o” Unbalance S/W error : “Ub ” Water Leakage error : “LE ” Overflow error : “OE ” Condition Solution Fault Water level sensor fails to send signal for longer than 5 seconds. Press “POWER” button. No other buttons work. Bad PCB or Pressure Sensor S/W. This occurs when the water supply is not finished in 1 hour or there is no change in the water level 4 minutes after the water supply has started. Press “POWER” button or “START/PAUSE” button. No other buttons work. Bad PCB or Pressure Sensor S/W, or Water-Valve Water level does not decrease to reset point within 15 minutes from draining water from washer. Press “POWER” button. No other buttons work. Bad PCB or Pump Moter. Lid is opened during wash cycle. Close lid. Bad PCB, Lid S/W, or Unbalance S/W. Unbalanced load is sensed three times during a wash cycle. Open lid. Rebalance laundry load and close lid. Bad PCB or Unbalance S/W. Press “POWER” button. Bad PCB, Pressure sensor S/W, Pump motor. Press “POWER” button. Bad Drain hose, water valve, Pressure sensor S/W. This occurs when it detects that the water level has fallen below the reset water level for the third time. This occurs when overflow is sensed during temporary stop, waiting action or spin action, otherwise overflow is sensed three times during a wash or rinse cycle. – 34 – Service Test Mode The washer control has a service test mode that can be utilized by the service technician in order to test critical components. This test mode will help the service technician to quickly identify failed or improper operation of certain washer components. Machine must be in idle mode before entering test. Idle mode occurs when the washer has completed a cycle. To enter the service test mode, press simultaneously the OPTIONS, CYCLES, and POWER pads for 1 second. All LEDs will briefly illuminate, then the display will alternately show MICOM number and MICOM version every 2 seconds. Repeated pressing of the START/PAUSE pad initiates specific tests. See table below. To exit test mode press POWER pad. SERVICE MODE TEST Water level sensor-test #1 Water level sensor-test #2 Water level sensor-test #3 Drain and spin, lid open, and unbalance switch test Weight sensing test (See Note) Water valve test Motor test Drain pump test DISPLAY ACTION Fills to extra large level, starts wash. To pump out, repeatedly press START/PAUSE pad until appears in the display. Fills to small level, starts wash. To pump out, repeatedly press START/PAUSE pad until appears in the display. Fills to extra large level. To pump out, repeatedly press START/ PAUSE pad until appears in the display. Starts drain and initiates spin. After 4 failed spin attempts, 3E error, is displayed and error sound is audible. If 3E appears and motor is not operating, replace it. If 3E appears and the motor is operating properly, replace the PCB. If washer drains and spins; lid switch, unbalance switch, and motor OK. Weight sensing begins, then display shows weight sensing data. Press TEMP pad repeatedly to test cool, rinse, and hot water functionality: First press = Cool, Second press = Rinse, Third press = Hot, Fourth press = Off. Press LOAD pad repeatedly to test motor/pulsator rotation: First press = Motor rotates pulsator CW, Second press = Off, Third press = Motor rotates pulsator CCW, Fourth press =Off. Press OPTIONS pad repeatedly to test drain pump: First press = Pump out, Second press = Off Note: Before weight sensing test is initiated, make sure that no water remains in the washer. If water is remaining in the washer, inaccurate data will be displayed, or the test will not proceed. To pump out, repeatedly press START/PAUSE pad until appears in the display. With no clothing in the tub, when placed in the HA test, the following occurs: 1. Weight sensing begins. 2. Weight sensing ends, only the appropriate load light stays lit, and the display shows corresponding weight sensing data. The load light will indicate load size. Adding additional dry clothing, (not water( will decrease the data number as weight is increased. Data readouts are approximate: Extra Small = 97, Small = 89-96, Medium = 82-88, Large = 76-81, and Extra Large = 75 or lower. If the Soak light remains lit, 100 will be added to the display number. – 35 – 2 BLUE – 36 – BLACK COIL 1 WHITE FUSE AC25OV / 12A COIL 2 DOOR S/W BLUE 1 SKYBLU BLACK 1 3 BLACK WHITE 1 1 [BLACK] 1 1 [WHITE] PRESSURE SENSOR 2 RINSE WATER EARTH 5 6 4 3 POWER COOL WATER 1 YELLOW GRAY BROWN RED HOT WATER 2 VIOLET PINK CN6 WHITE BLACK YELLOW 10 5 11 4 YELLOW C O N T R O L 2 1 CN3 YELLOW 1 1 DRAIN PUMP MOTOR 11.77 1 1 BRAKE CONTROL MOTOR 2 1.5K7 1 1 3 2 1 CN5 RED 1 CN4 WHITE 1 [WHITE] 1 3 3 3 3 1 1 BLACK YELLOW YELLOW YELLOW BLACK BLACK BLUE BLUE RED RED YELLOW YELLOW RED BLUE [BLUE] CONDENSOR YELLOW YELLOW WASHING MOTOR WHITE YELLOW P C B WHITE 1 ORANGE UNBALANCE S/W CN1 WHITE RED RED BLACK BLUE BLUE CN2 BLACK Schematic Warranty GE Washer Warranty. (For customers in the U.S.A.) All warranty service provided by our Factory Service Centers, or an authorized Customer Care® technician. To schedule service, on-line, visit us at ge.com, or call 800.GE.CARES (800.432.2737). Please have serial number and model number available when calling for service. Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty. For The Period Of: We Will Replace: One Year From the date of the original purchase Any part of the washer which fails due to a defect in materials or workmanship. During this limited one-year warranty, GE will also provide, free of charge, all labor and related service costs to replace the defective part. What Is Not Covered (in the United States): ■ Service trips to your home to teach you how to use ■ Replacement of house fuses or resetting of circuit the product. ■ Improper installation, delivery or maintenance. ■ Failure of the product if it is abused, misused, or used for other than the intended purpose or used commercially. ■ Damage after delivery. breakers. ■ Damage to the product caused by accident, fire, floods or acts of God. ■ Incidental or consequential damage caused by possible defects with this appliance. ■ Product not accessible to provide required service. EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home. Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General. Warrantor: General Electric Company. Louisville, KY 40225 – 37 –
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2009:09:25 18:12:27-04:00 Create Date : 2009:09:25 08:23:44-04:00 Metadata Date : 2009:09:25 18:12:27-04:00 Format : application/pdf Title : untitled Producer : Acrobat Distiller 8.1.0 (Windows) Document ID : uuid:24044bc2-1ee2-49e5-b74d-f3eb82609306 Instance ID : uuid:583eddd5-7e8b-486d-8d31-b82786f80d0e Page Count : 37EXIF Metadata provided by EXIF.tools