Iconix All Suture Anchor Brochure

Iconix All Suture Anchor Brochure iconix_all_suture_anchor_brochure iconix_all_suture_anchor_brochure 3 2013 pdf 258413772373414384

: Pdf Iconix All Suture Anchor Brochure iconix_all_suture_anchor_brochure 2 2013 pdf

Open the PDF directly: View PDF .
Page Count: 8

All Suture Anchor

with IntelliBraid Technology

e ICONIX family of anchors symbolize the next generation of suture anchor technology. e all suture based system

allows for less bone removal during pilot hole creation without compromising pullout strength. e innovative design is

truly the rst of its kind.

Introduction

Searching For a Better Option

IntelliBraid Technology

Without SC Technology

e IntelliBraid Technology creates a bunching eect using targeted compression zones within the implant sheath for optimal xation.

Self-Centering Technology

e ICONIX disposable drills feature a unique Self Centering (SC) Technology, to ensure accurate pilot hole placement.

With SC Technology

12.0 mm

Measurements - Aer

ICONIX 1

4.5 mm

3.0 mm

ICONIX 2,3,25

Measurements - Before

4.0 mm

8.0 mm

Competitive Advantages

• Four all suture congurations

• A completely all suture based implant made of HSS (Force Fiber) and a polyester sheath

• Helps eliminate the possibility of loose bodies in the joint due to anchor breakage

ICONIX 1

1 strand #2 Force Fiber

Use w/1.4mm instrumentation

ICONIX 2

2 strands #2 Force Fiber

Use w/2.3mm instrumentation

ICONIX 3

3 strands #2 Force Fiber

Use w/2.3mm instrumentation

ICONIX 25

2 strands #5 Force Fiber

Use w/2.3mm instrumentation

• Smaller drill allows for minimal bone removal

during pilot hole creation

• More anchors can be placed in smaller footprint

Typical

3.0mm Drill Hole

ICONIX

2.3mm Drill Hole

ICONIX

1.4mm Drill Hole

Anchors

Pilot Hole

• e ICONIX Anchor System is intelligently sized and color coded to reduce risk of human error

Intelligent Design

2.3mm1.4mm

Competitive Advantages

• Smaller drill guides cause less damage to surrounding tissue

• Universal crown tips can be used on the face and rim of the glenoid

• Options when you need them

• e ICONIX Anchor System was specically designed for both Rotator Cu and Instability repairs, with curved

and straight option guides

Rotator Cuff

Instability

Straight Short

Straight

12º

25º

2.3mm 1.4mm

Guides

Competitive Advantages

• e ICONIX Anchor System is specically designed for Hip FAI procedures with curved and straight guide options

• Designed to provide proper guide length during all FAI cases

• Directs anchor trajectory away from the acetabular socket

• Unique SLANT mouth helps place anchor closer to the acetabulum rim, allowing for a more anatomic repair

2.3mm 1.4mm

12º Slant

25º Slant

3mm

Hip - FAI

Technique

Rotator Cuff

Instability

Hip - FAI

Take selected drill guide and place on

bone in preferred position.

Insert the awl or drill into the drill

guide and advance until positive

stop is hit.

Insert anchor, lightly mallet to fully seat the

anchor into the bone until positive stop is

hit. Untether the suture from the inserter

handle. Pull the anchor inserter handle.

Pull on all sutures to set the anchor.

Take selected drill guide and place on

bone in preferred position.

Insert the drill into the drill guide and

advance until positive stop is hit.

Insert anchor, lightly mallet to fully seat the

anchor into the bone until positive stop is

hit. Untether the suture from the inserter

handle. Pull the anchor inserter handle.

Pull on all sutures to set the anchor.

(Instructions for Hip - FAI are same

as for Instability)

Pull-out Strength1

Competitive Advantages

Stryker ICONIX 25

Stryker ICONIX 3

Stryker ICONIX 2

Stryker ICONIX 1

Biomet JuggerKnot

single loaded

Linvatec Y-Knot

single loaded

0 100 200 300 400 500 600

Anchor

Ultimate Pull-out Force (N)

One pound force is approximately equal to 4.5 Newtons

• Cannulated obturators help save time while gaining access to the hip joint

Cannulated Obturator

A surgeon must always rely on his or her own professional clinical judgment when deciding whether to use a particular

product when treating a particular patient. Stryker does not dispense medical advice and recommends that surgeons be

trained in the use of any particular product before using it in surgery.

The information presented is intended to demonstrate the breadth of Stryker product offerings. A surgeon must always

refer to the package insert, product label and/or instructions for use before using any Stryker product. Products may not be

available in all markets because product availability is subject to the regulatory and/or medical practices in individual mar-

kets. Please contact your Stryker representative if you have questions about the availability of Stryker products in your area.

Stryker Corporation or its divisions or other corporate affiliated entities own, use or have applied for the following trade-

marks or service marks: ICONIX, Stryker. All other trademarks are trademarks of their respective owners or holders.

Force Fiber is a registered trademark of Teleflex Incorporated.

Literature Number: LJPICX-B

MS/GS 09/12

Copyright © 2012 Stryker

Printed in USA

325 Corporate Drive

Mahwah, NJ 07430

t: 201 831 5000

www.stryker.com

325 Corporate Drive

Mahwah, NJ 07430

t: 201 831 5000

www.stryker.com

References:

Tech Report # RD-12-080

PART NUMBER DESCRIPTION

3910-500-512

3910-500-522

3910-500-532

3910-500-525

3910-500-550

3910-500-551

3910-500-552

3910-500-553

3910-500-554

3910-500-555

3910-500-556

3910-500-557

3910-500-558

3910-500-559

3910-500-560

3910-500-561

Obturator

3910-500-562

3910-500-563

3910-500-564

3910-500-565

3910-500-566

3910-500-567

Drills / Awl

3910-500-568

3910-500-569

3910-500-571

3910-500-573

3910-500-574

Tray

3910-500-575

ICONIX 1 with IntelliBraid Technology, 1.4mm Anchorwith 1 strand #2 Force Fiber

ICONIX 2 with IntelliBraid Technology, 2.3mm Anchor with 2 strands #2 Force Fiber

ICONIX 3 with IntelliBraid Technology, 2.3mm Anchor with 3 strands #2 Force Fiber

ICONIX 25 with IntelliBraid Technology, 2.3mm Anchor with 2 strands #5 Force Fiber

ICONIX Straight Guide SHORT for 1.4mm anchor

ICONIX Straight Guide SHORT for 2.3mm anchor

ICONIX Straight Guide for 1.4mm anchor

ICONIX 12º Guide for 1.4mm anchor

ICONIX 25º Guide for 1.4mm anchor

ICONIX Straight Guide for 2.3mm anchor

ICONIX 12º Guide for 2.3mm anchor

ICONIX 25º Guide for 2.3mm anchor

ICONIX SLANT 12º Guide for 1.4mm anchor

ICONIX SLANT 25º Guide for 1.4mm anchor

ICONIX SLANT 12º Guide for 2.3mm anchor

ICONIX SLANT 25º Guide for 2.3mm anchor

ICONIX Pencil Tip Obturator SHORT for 1.4mm anchor

ICONIX Pencil Tip Obturator SHORT for 2.3mm anchor

ICONIX Trocar Tip Obturator for 1.4mm anchor

ICONIX Trocar Tip Obturator for 2.3mm anchor

ICONIX Cannulated Bullet Obturator for 1.4mm anchor

ICONIX Cannulated Bullet Obturator for 2.3mm anchor

ICONIX 1.4mm Disposable Drill

ICONIX 2.3mm Disposable Drill

ICONIX 1.4mm Reusable Straight Drill

ICONIX 2.3mm Reusable Straight Drill

ICONIX 2.3mm Reusable Awl

Multi-System Reusable Tray

Anchors

Guides