Kenmore Front Load Washer Wiring Sheet 417.24182301
2013-04-09
: Pdf Kenmore Front Load Washer Wiring Sheet 417.24182301 Kenmore Front Load Washer Wiring Sheet 417.24182301 Kenmore
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
TECH SHEET - RETAIN FOR SERVICE TECHNICIAN Disconnect from Electrical Supply Before Servicing Washer. Timer/off Door/open WIRING DIAGRAM 6 AQUA 4.3 BLK/WHT #4 #6 BLK/RED AQUA RED C10.8 (F) C10.9 (E) C10.10 (D) SOFTENER 2 C10.6 (C) BLEACH 7B TIMER T B DIRECT 12 C6.6 (AC) BLK 2 5B AQUA 3 2 WATER LEVEL PRESSURE SWITCH 3M 3B BROWN TAN/BLK 1 1B WHT/RED YELLOW JUMPER WIRE 4M 6F 7C 2 1 5M 5C BLUE 0C 0T 3C C10.2 (A) BLK 1C PINK/BLK 2.2 C10.1 (B) TIMER LINE SWITCH 1 PURPLE SLIDE COIN METER 4.4 DOOR LOCK COIL 3 4M YELLOW 2.1 5M 2 B T TIMER MOTOR RINSE WATER #2 PINK 1 HOT C10.3 (T2) 1 5 MOTOR WINDING BLUE WATER VALVES T TACHOGENERATOR COLD 1 WAX MOTOR BLU/ WHT PTC 2 BLEACH DOOR LAMP 3 SOFTENER 1 2 C6.3 (P3) C6.2 (P2) C6.4 4 MS 10 WASH WATER 6 JUMPER POSITION FOR MANUAL WASHERS 6 3 5 GRAY 2 3F WHT/RED 2 3M ORG/WHT M YELLOW 1 C 1 WASH WATER RED/BLK 6M 8 B ORG/BLK 5F 6F BLK/WHT 14 GREEN 5M T T YEL/WHT 4F T TEMP SWITCH 4M 4 YEL/BLK B START SWITCH TAN/WHT C10.5 (TM) 2B C10.4 (T1) C6.1 (P1) MOTOR CONTROL DROP COIN METER C6.5 (AC) L1 TEMPERATURE SWITCH DOOR LOCK SWITCH PUMP MOTOR M +t 2 6C 6T DISPENSER VALVES #3 #1 N WHT BLU/WHT DISPENSER DRAWER REED SWITCH 2 1 WHT WATER TEMP SWITCH #7 SWITCH POSITION WHT W/R GND #5 GRN CABINET DASHED LINES = NOT ON ALL MODELS BOLD LINES = INTERNAL TIMER CIRCUIT COIN METER COLD WARM DELICATE HOT CIRCUIT 1-3 1-5 X X X 2-6 X X X X Motor Will Not Run 1. CHECK FOR POWER: Advance the timer knob to the drain increment. If the drain pump does not run, check household safety circuit. If the drain pump runs go to step 2. 2. CHECK FOR MOTOR MOVEMENT: Turn the water off to the washer. Remove electrical power from the washer and remove the back panel. Remove the motor drive belt. Reconnect electrical power and set the timer to the start of the Regular wash cycle and pull the knob out. If motor does not rotate, check for a poor connection in the timer line switch, coin box circuit, or door lock switch. If good, and motor does not run go to Step 3. 3. MEASURE VOLTAGES: Remove the six pin plug from the speed control unit. Measure the voltage between pins 5 and 6 on the harness. If the meter reads 0 check the connection in the timer line switch or door lock. If the meter reads 120 Vac go to step 4. 6 Speed Control 4. Set the timer to the Heavy Wash position of the Regular wash cycle. Remove the ten pin plug from the speed control unit. Measure the voltage between pins 1, 2, 6 and 10 of the ten pin plug to pin 5 of the 6 pin plug on the harness. The voltage at pins 2, 6, and 10 should read 120 Vac and 0 Vac at pin 1. If not, check timer contacts 1C to 1B, 5C to 5B, and 7C to 7B for closed contacts, and 3C to 3B for open contacts. If the voltage readings are correct, go to step 5. 7. Remove electrical power from the washer. With an ohmmeter check the resistance between pins 1 and 2, 2 and 3, and 3 and 1 of the six pin plug on the harness. If the meter reads other than 2.6 ohms ± 7%, replace the motor. Speed Control 6 5 10 1 6 1 6 Speed Control Quick Facts 1 5. MEASURE RESISTANCES: Check the fuse on the speed control board. If the fuse is open, replace the speed control board. If good, go to step 6. 6. Remove the 6 pin plug from the speed control unit. Measure the resistance between pins 1 and 2, 2 and 3, and 3 and 1 of the speed control unit. If the meter reads other than 3 Meg ohms ± 10%, replace the speed control board. • The timer motor will not run continuously. The speed control unit controls the timer motor and advances the timer when needed. • In some tumble modes, the tub may not tumble for the first 16 to 20 seconds after start-up. • Extremely low water pressure may cause tub rotation to stop until WLC satisfied. 1 IMPORTANT SAFETY NOTICE This information is intended for use by technicians possessing adequate background of electrical, electronic and mechanical experience. Any attempt to repair a major appliance may result in personal injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use. IMPORTANT If grounding wires, screws or clips used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened. Certain internal parts are intentionally NOT grounded and may present a risk of electric shock only during servicing. Do not contact the following parts while the appliance is energized: pump, drive motor and electronic control boards. PART NO. 134578300 This information is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. The seller or manufacturer cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of this data. ! WARNING L1 N DOOR LOCK SOLENOID WON'T ENERGIZE (Timer In OFF Position - Metered Machine) 4.4 COIN METER SWITCH L1 N IF NO MOTOR ROTATION DURING FILL OR AGITATION 2.1 C6.6 (AC) DOOR LOCK COIL PUSH-TO-START SWITCH DOOR LOCK SOLENOID WON'T ENERGIZE (Timer In OFF Position - Non-Metered Machine) 2.1 4.4 JUMPER WIRE DOOR LOCK COIL PUSH-TO-START SWITCH DOOR LOCK SOLENOID WON'T ENERGIZE OT YELLOW JUMPER WIRE (OPTIONAL) 4.4 OC TIMER C6.1 (P1) (PHASE 2) 2 C6.2 (P2) (PHASE 3) 1 C6.3 (P3) C10.3 (T2) (TACH) 5 (TACH) 6 C10.4 (T1) (GND) 4 C6.4 (GND) MOTOR DOOR LOCK COIL 1 0T 0C 2.2 TIMER OC TIMER (PHASE 1) 3 2.1 DOOR LAMP WON'T LIGHT OT C6.5 (AC) 4.3 DOOR LOCK 1C 3 2 WATER LEVEL SWITCH C10.2 (A) 1B 12T TIMER TIMER 3C C10.1 (B) 3B TIMER DOOR LAMP 5C TIMER CONTACTS 1, 3, 5 AND 7: C10.6 (C) 5B TIMER 7C REFER TO TIMER CHART FOR THE MOTOR CONTROL CODE AND MACHINE FUNCTION. C10.10 (D) 7B TIMER SPEED CONTROL IF NO HOT, WARM, OR COLD WATER DURING WASH FILL 3 1 OT OC TIMER 4.3 2.2 DOOR LOCK 2 2C WATER LEVEL SWITCH 4C 8T 1 8C 1 3 5 1 TEMP SWITCH YELLOW JUMPER WIRE (OPTIONAL) 2 REED SWITCH HOT WATER SOLENOID TIMER 1 10C 10B TIMER TEMP SWITCH 2 REED SWITCH COLD WATER SOLENOID IF NO MOTOR ROTATION DURING SPIN 0T 0C TIMER IF NO COLD WATER DURING RINSE FILL OT 0C TIMER 4.3 2.2 DOOR LOCK 1 2.2 4.3 DOOR LOCK 3 1 2 WATER LEVEL SWITCH 2C TIMER 4T 4C TIMER C6.6 (AC) 2C 4C TIMER 2 WATER LEVEL SWITCH 8T 10C 10T TIMER 1 COLD WATER SOLENOID 2 REED SWITCH C6.5 SPEED CONTROL 12C TIMER 4.3 2.2 DOOR LOCK MS 6T 6C TIMER MOTOR TIMER C6.5 (AC) (PHASE 1) 3 C6.1 (P1) (PHASE 2) 2 C6.2 (P2) (PHASE 3) 1 C6.3 (P3) (TACH) 5 C10.3 (T2) (TACH) 6 C10.4 (T1) (GND) 4 C6.4 (GND) MOTOR IF TIMER WON'T ADVANCE OC TIMER C10.8 (F) C10.9 (E) 3 C10.5 OT 6 2 1C 1B 12T 12C TIMER C10.2 (A) TIMER 3C 3B C10.1 (B) TIMER 5C 5B C10.6 (C) TIMER 7C IF WATER PUMP DOES NOT WORK (Models With Pump) M OT OC TIMER 4.3 2.2 DOOR LOCK 12C TIMER 7B TIMER 14C 14B TIMER C10.10 (D) SPEED CONTROL PUMP MOTOR IF WATER DUMP VALVE DOES NOT WORK (Models With Dump Valve) OT OC TIMER 4.3 2.2 DOOR LOCK 12C TIMER 14C 14T TIMER DUMP VALVE MOTOR NOTE: BOLD LINES INDICATE INTERNAL TIMER CIRCUITS. DIAGNOSTIC STRIP CIRCUITS IMPORTANT Reconnect all grounding devices, all parts of this appliance capable of conducting electrical current are grounded. If grounding wires, screws, straps, clips, nuts or washers used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened. PART NO. 134578300
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Count : 4 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:179a9ea0-3f91-4ea0-b35c-d7716dfead09 Producer : Acrobat Distiller 6.0 (Windows) Keywords : Creator Tool : Acrobat PDFMaker 6.0 for AutoCAD Modify Date : 2005:07:28 10:50:05-05:00 Create Date : 2005:07:28 10:50:05-05:00 Metadata Date : 2005:07:28 10:41:58-05:00 Document ID : uuid:a61e5b6a-ea8b-4682-b158-2739b31f5192 Format : application/pdf Title : untitled Creator : Description : Author : Subject :EXIF Metadata provided by EXIF.tools