Kl Sarhid Spec
2016-08-26
: Pdf Kl Sarhid Spec kl_sarhid_spec spec products kim
Open the PDF directly: View PDF 
.
Page Count: 5
| Download | |
| Open PDF In Browser | View PDF |
SAR The Archetype® revision 04/08/15 • kl_ sarhid_spec.pdf Type: Job: Catalog number: / / Approvals: / Mtg. Fixture Electrical Module Finish See page 2 / / Options See pages 3-4 Optional Vertical Slipfitter Mount See page 5 Select pole from Kim Pole Catalog. If pole is provided by others indicate O.D. for arm fitting. Specifications 70 to 150 watt 70 to 175 watt Medium Base Medium Base Lamps Maximum Fixtureweight weight (150HPS) Maximum Fixture (150HPS) = 25=lb25 lb 5" 6" 17B" 4J" 1L" Arm cross-section 12" Date: Page: 1 of 5 Housing: One-piece die-cast, low copper (<0.6% Cu) aluminum alloy with integral cooling ribs over the optical chamber and electrical compartment. Solid barrier wall separates optical and electrical compartments. Double-thick wall with gussets on the support-arm mounting end. The fixture’s housing forms a half cylinder with 58° front face plane providing a recess to allow a flush single-latch detail. All hardware is stainless steel or electro-zinc plated steel. Lens Frame: One-piece die-cast, low copper (<0.6% Cu) aluminum alloy lens frame with 1" minimum depth around the gasket flange. Integral hinges with stainless steel pins provide no-tool mounting and removal from housing. Single die-cast aluminum am-latch provides positive locking and sealing of the optical chamber by a one piece extruded and vulcanized silicone gasket to provide an IP66 rating for the optical module. Clear F" thick tempered glass lens retained by eight steel clips with full silicone gasketing around the perimeter. Reflector Module: Specular Alzak® optical segments are rigidly mounted within a die-cast aluminum enclosure that attaches to the housing as a one-piece module. Reflector module is field rotatable in 90° increments. PMH and HPS sockets are porcelain 4KV pulse rated medium base. All reflector modules are factory prewired with quick-disconnect plug and include silicone seal at the penetration of the internal barrier wall in the luminaire housing. Electrical Module: All electrical components are UL and CSA recognized, mounted on a single plate and factory prewired with quick-disconnect plugs. Electrical module attaches to housing with no-tool hinges and latches, accessible by opening the lens frame only. All ballasts are high power factor rated -20°F. starting. Support Arm: One-piece extruded aluminum with internal bolt guides and fully radiussed top and bottom. Luminaire-to-pole attachment is by internal draw bolts, and includes a pole reinforcing plate with wire strain relief. Arm is circular cut for specified round pole. Optional Wall Mounting: Fixture mounts to 3" or 4" junction boxes by a cast aluminum adapter plate with fixture mounting bolts. Finish: Each luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) polyester powdercoat finish. Standard colors include (BL) Black, (DB) Dark Bronze, (WH) White, (PS) Platinum Silver, (SG) Stealth Gray, (LG) Light Gray, and (CC) Custom Color (Include RAL#). Caution: Fixtures must be grounded in accordance with local codes or the National Electrical Code. Failure to do so may result in serious personal injury. UL cUL 15981 1 Listings and Ratings CE Suitable for wet locations. 25C Ambient KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE. © 2015 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716 SAR The Archetype® revision 04/08/15 • kl_ sarhid_spec.pdf Type: Job: Page: 2 of 5 Standard Features Mounting 3SY configuration is available for round poles only. Plan View: Wall Mount EPA: 0.7 1.4 1.2 1.9 1.9 2.5 Cat. No.: l 1SA l 2SB l 2SL l 3ST l 3SY l 4SC l 1W Fixture Cat. No. designates fixture and light distribution. See the Kim Site/Roadway Optical Systems Catalog for detailed information on reflector design and application. Electrical Module HPS = High Pressure Sodium PMH = Pulse Start Metal Halideh Lamp Lamp Line Watts Type Volts 150 HPS 120 Flat Lens Light Distribution: Type I Type II Type III Full Cutoff Full Cutoff Full Cutoff Cat. No.: l SAR1 l SAR2 l SAR3 Cat. Nos. for Electrical Modules available: High Pressure Sodium l 70HPS120 l 100HPS120 l 70HPS208 l 100HPS208 l 70HPS240 l 100HPS240 l 70HPS277 l 100HPS277 l 70HPS347 l 100HPS347 l 70HPS480 l 100HPS480 Lamp ED-17, Clear Socket Medium Base ANSI Ballast S-62 Pulse Start Metal Halide l 70PMH120 l 70PMH208 l 70PMH240 l 70PMH277 l 70PMH347 l 70PMH480 Lamp ED-17, Clear Socket Medium Base ANSI Ballast M-98 Type IV Forward Throw Full Cutoff l SAR4 Type V Square Full Cutoff l SAR5 l 150HPS120 l 150HPS208 l 150HPS240 l 150HPS277 l 150HPS347 l 150HPS480 ED-17, Clear ED-17, Clear Medium Base S-54 Medium Base S-55 l 100PMH120 l 100PMH208 l 100PMH240 l 100PMH277 l 100PMH347 l 100PMH480 l 150PMH120 l 150PMH208 l 150PMH240 l 150PMH277 l 150PMH347 l 150PMH480 ED-17, Clear Medium Base M-90 ED-17, Clear Medium Base M-102 Note: Due to the Energy Independence and Security Act (EISA) of 2007, Kim Lighting can no longer supply probe start metal halide ballasts with its luminaires, effective January 1, 2009. Contact Kim Lighting for availability of replacement ballasts for warranty service claims. (Visit www.aboutlightingcontrols.org or the Library of Congress website for more details). Finish TGIC powder coat Color: Black Dark Bronze Cat. No.: l BL l DB Light Gray Stealth Gray l LG l SG Platinum Silver White l PS l WH Custom Color1 l CC Custom colors subject to additional charges, minimum quantities and extended lead times. Consult representative. Custom color description: 1 © 2015 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716 SAR The Archetype® revision 04/08/15 • kl_ sarhid_spec.pdf Type: Job: Page: 3 of 5 Optional Features Wall Mounting Cat. No. l 1W l No Option Select from Mounting on page 2. Photocell Control Cat. No. (See right) l No Option≠ Fixture mounts to 3" or 4" junction boxes by a cast aluminum adapter plate with fixture mounting bolts. NOTE: Junction box in wall must provide adequate fixture support. See NEC sections 370-13, 17 and 410-14, 16. Quick-disconnect plug and wiring are provided to allow field connections prior to fixture mounting. Fixture supplied with an internal photocell with the sensor on the fixture end facing the pole. For multiple-fixture pole mountings, one fixture has a photocell to operate the others. Not available if wall mounted (1W). Cat. No. l A-30 l A-31 l A-32 l A-33 l A-35 l A-34 Convex Glass Lens Cat. No. l CGL l No Optionˇ Polycarbonate Lens Cat. No. l LS l No Option Quartz Standby Cat. No. l QS l No Option Line Volts: 120V 208V 240V 277V 347V 480V 4L" Wall mount using adapter plate 3" or 4" J-box in wall (by others)^ Mounting Configuration: S – Fixture with Photocell Sensor S – slave unit(s) No fixture wattage limit.e s S S 1SA S 2K" The F" thick clear convex tempered glass lens replaces the standard flat glass lens. Provides increased lens presence and provides a subtle improvement in uniformity where pole spacing is extreme. Increases effectiveness of houseside shielding. 2SL s 2SB s s s Photocell Sensor J-box H" s s S S 3ST, 3SY 4SC 1L" Fixture supplied with a one piece vacuum formed, clear, UV stabilized convex polycarbonate, fully gasketed, replacing the standard tempered glass lens. CAUTION: Use only when vandalism is anticipated to be high. Useful life is limited by UV discoloration from sunlight and metal halide lamps. Integral electronic device energizes a T-4 mini-can socket during initial lamp start-up or after a power interruption. De-energizes prior to HID lamp reaching full brightness. T-4 halogen lamp by others; 100 watt maximum. © 2015 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716 4" Convex Glass Lens 3" Polycarbonate Lens SAR The Archetype® revision 04/08/15 • kl_ sarhid_spec.pdf Type: Job: Page: 4 of 5 Optional Features Houseside Shield Cat. No. (See right) l No Option (Types II, III, and IV only) Fixtures with the standard flat glass lens are available with stamped aluminum louvers that pass streetside light and block houseside light, and a blackened panel added to the reflector to reduce houseside reflections. Fixtures with the optional convex glass lens are available with a formed aluminum shield that passes streetside light and blocks houseside light, and a black anodized panel added to the reflector to reduce houseside reflections. Use with clear lamps only, as coated lamps reduce effectiveness.Ü Cat. No. l HS l HSC Neighbor Friendly Shield Cat. No. l NFS l No Option Tamper-Resistant Latch Cat. No. l TL l No Option Horizontal Slipfitter Mount Cat. No. l HSF l No Option HS for flat lens HSC for convex lens or polycarbonate lens Recommended for use with clear lamps only. Effectiveness is reduced for coated lamps. Not for use with Type V light distributions. For use with all fixtures with convex glass lens. Not for use with Type V light distributions. (Type IV only) Stamped internal shield and blocking panels are used to direct and redirect lighting into a forward throw distribution. The amount of light directed and redirected toward the back of the liminaire is dramatically reduced to create extremely low glare behind the pole. Only available on the Type IV reflectors.h Standard die-cast latch is provided with a captive 10-32 stainless steel flat socket-head screw to prevent unauthorized opening. NOTE: Required only for vandal protection in locations where fixtures can be reached by unauthorized persons. Replaces standard mounting arm with a slipfitter which allows fixture to be mounted to a horizontal pole davitarm with 2" pipe-size mounting end (2C" O.D.). Cast aluminum slipfitter with set screw anti-rotation lock. Bolts to housing from inside the electrical compartment using mounting holes for the standard support arm. Davit-arm must be field drilled at a set screw location to insure against fixture rotation. Finished to match fixture and arm. NFS Tamper-Resistant Latch Davit-arm with 2" pipe-size fixture mount (by others) Horizontal Slipfitter Mount by Kim © 2015 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716 SAR The Archetype® revision 04/08/15 • kl_ sarhid_spec.pdf Type: Job: Page: 5 of 5 Optional Features Vertical Slipfitter Mounts Cat. No. includes Mounting Cat. No. (See right) l No Option Allows fixture with standard support arm to be mounted to poles having a 2" pipe-size tenon (2C" O.D. x 4K" min. length). All mounting configurations can be used (1SA, 2SB, 2SL, 3ST, 3SY, 4SC). 4" square or round die-cast aluminum with flush cap, secured by four C" stainless steel set point allen screws, finished to match fixture and arm. NOTE: 3SY only available on round slipfitter. Cat. No. l VSF-1SA l VSF-2SB l VSF-2SL l VSF-3ST l VSF-3SY l VSF-4SC Round Stainless steel set screws Square Pole with 2" pipe-size tenon (by others) Vertical Slipfitter Mount by Kim Cat. No. Mounting Configuration l SVSF-1SA 1SA - single arm mount l SVSF-2SB 2SB - 2 at 180° l SVSF-2SL 2SL - 2 at 90° l SVSF-3ST 3ST - 3 at 90° 3SY - 3 at 120° l SVSF-4SC 4SC - 4 at 90° © 2015 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2015:04:08 07:40:30-07:00 Metadata Date : 2015:04:08 07:40:32-07:00 Modify Date : 2015:04:08 07:40:32-07:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:6b929ae8-30a5-e745-8557-c6da7ac99568 Original Document ID : xmp.did:F87F11740720681188C6CB66EB0B0C52 Document ID : xmp.id:B003FA740920681188C6CB66EB0B0C52 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:AF03FA740920681188C6CB66EB0B0C52 Derived From Document ID : xmp.did:AF03FA740920681188C6CB66EB0B0C52 Derived From Original Document ID: xmp.did:F87F11740720681188C6CB66EB0B0C52 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2015:04:08 07:40:30-07:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 5 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools