Kl Sarhid Spec
2016-08-26
: Pdf Kl Sarhid Spec kl_sarhid_spec spec products kim
Open the PDF directly: View PDF 
.
Page Count: 5
Housing: One-piece die-cast, low copper (<0.6% Cu) aluminum
alloy with integral cooling ribs over the optical chamber and electrical
compartment. Solid barrier wall separates optical and electrical
compartments. Double-thick wall with gussets on the support-arm
mounting end. The fixture’s housing forms a half cylinder with 58°
front face plane providing a recess to allow a flush single-latch detail.
All hardware is stainless steel or electro-zinc plated steel.
Lens Frame: One-piece die-cast, low copper (<0.6% Cu) aluminum
alloy lens frame with 1" minimum depth around the gasket flange.
Integral hinges with stainless steel pins provide no-tool mounting and
removal from housing. Single die-cast aluminum am-latch provides
positive locking and sealing of the optical chamber by a one piece
extruded and vulcanized silicone gasket to provide an IP66 rating for
the optical module. Clear F" thick tempered glass lens retained by
eight steel clips with full silicone gasketing around the perimeter.
Reflector Module: Specular Alzak® optical segments are rigidly
mounted within a die-cast aluminum enclosure that attaches to the
housing as a one-piece module. Reflector module is field rotatable
in 90° increments. PMH and HPS sockets are porcelain 4KV pulse
rated medium base. All reflector modules are factory prewired with
quick-disconnect plug and include silicone seal at the penetration of the
internal barrier wall in the luminaire housing.
Electrical Module: All electrical components are UL and CSA
recognized, mounted on a single plate and factory prewired with
quick-disconnect plugs. Electrical module attaches to housing with
no-tool hinges and latches, accessible by opening the lens frame only.
All ballasts are high power factor rated -20°F. starting.
Support Arm: One-piece extruded aluminum with internal bolt guides
and fully radiussed top and bottom. Luminaire-to-pole attachment is by
internal draw bolts, and includes a pole reinforcing plate with wire strain
relief. Arm is circular cut for specified round pole.
Optional Wall Mounting: Fixture mounts to 3" or 4" junction boxes by
a cast aluminum adapter plate with fixture mounting bolts.
Finish: Each luminaire receives a fade and abrasion resistant,
electrostatically applied, thermally cured, triglycidal isocyanurate
(TGIC) polyester powdercoat finish. Standard colors include (BL) Black,
(DB) Dark Bronze, (WH) White, (PS) Platinum Silver, (SG) Stealth Gray,
(LG) Light Gray, and (CC) Custom Color (Include RAL#).
CAUTION: Fixtures must be grounded in accordance with local codes
or the National Electrical Code. Failure to do so may result in serious
personal injury.
Approvals:
Specifications
Date:
Page: 1 of 5
© 2015 KIM LIGHTING • 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
SAR
The Archetype®
revision 04/08/15 • kl_ sarhid_spec.pdf
70 to 175 watt
Medium Base Lamps
5"
12"
Maximum Fixture weight (150HPS) = 25 lb
Arm
cross-section
1L"
4J"
17B"
6"
Type:
Job:
Catalog number:
Select pole from Kim Pole Catalog. If pole is provided by others indicate O.D. for arm fitting.
/ / / / /
Mtg. Fixture Electrical Module Finish Options Optional
See pages 3-4
Vertical
Slipfitter Mount
See page 5
See page 2
Listings and Ratings
UL cUL 15981 CE 25C Ambient
1Suitable for wet locations.
KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE.
70 to 150 watt
Medium Base
Maximum Fixture weight (150HPS) = 25 lb
Mounting
3SY configuration is available
for round poles only.
Finish
TGIC powder coat
Plan View:
Flat Lens
1Custom colors subject to additional charges, minimum quantities and extended lead times.
Consult representative. Custom color description:
Wall Mount
Page: 2 of 5
Type:
Job:
EPA: 0.7 1.4 1.2 1.9 1.9 2.5
Cat. No.: l 1SA l 2SB l 2SL l 3ST l 3SY l 4SC l 1W
Standard Features
© 2015 KIM LIGHTING • 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
SAR
The Archetype®
revision 04/08/15 • kl_ sarhid_spec.pdf
Electrical Module
HPS = High Pressure
Sodium
PMH = Pulse Start Metal
Halideh
Cat. Nos. for Electrical Modules available:
Lamp Lamp Line
Watts Type Volts
150 HPS 120
High Pressure Sodium
l 70HPS120 l 100HPS120 l 150HPS120
l 70HPS208 l 100HPS208 l 150HPS208
l 70HPS240 l 100HPS240 l 150HPS240
l 70HPS277 l 100HPS277 l 150HPS277
l 70HPS347 l 100HPS347 l 150HPS347
l 70HPS480 l 100HPS480 l 150HPS480
Lamp ED-17, Clear ED-17, Clear ED-17, Clear
Socket Medium Base Medium Base Medium Base
ANSI Ballast S-62 S-54 S-55
Pulse Start Metal Halide
l 70PMH120 l 100PMH120 l 150PMH120
l 70PMH208 l 100PMH208 l 150PMH208
l 70PMH240 l 100PMH240 l 150PMH240
l 70PMH277 l 100PMH277 l 150PMH277
l 70PMH347 l 100PMH347 l 150PMH347
l 70PMH480 l 100PMH480 l 150PMH480
Lamp ED-17, Clear ED-17, Clear ED-17, Clear
Socket Medium Base Medium Base Medium Base
ANSI Ballast M-98 M-90 M-102
Fixture
Cat. No. designates fixture
and light distribution.
See the Kim Site/Roadway
Optical Systems Catalog for
detailed information on re-
flector design and applica-
tion.
Light Distribution: Type I Type II Type III Type IV Type V
Forward Throw Square
Full Cutoff Full Cutoff Full Cutoff Full Cutoff Full Cutoff
Cat. No.: l SAR1 l SAR2 l SAR3 l SAR4 l SAR5
Color: Black Dark Bronze Light Gray Stealth Gray Platinum Silver White Custom Color1
Cat. No.: l BL l DB l LG l SG l PS l WH l CC
NOTE: Due to the Energy Independence and Security Act (EISA) of 2007, Kim Lighting can no longer supply probe start
metal halide ballasts with its luminaires, effective January 1, 2009. Contact Kim Lighting for availability of replacement
ballasts for warranty service claims.
(Visit www.aboutlightingcontrols.org or the Library of Congress website for more details).
H"
4L"
Page: 3 of 5
Fixture mounts to 3" or 4" junction boxes by a cast alu-
minum adapter plate with fixture mounting bolts.
NOTE: Junction box in wall must provide adequate
fixture support. See NEC sections 370-13, 17 and
410-14, 16. Quick-disconnect plug and wiring are pro-
vided to allow field connections prior to fixture
mounting.
Wall Mounting
Cat. No. l 1W
l No Option
Select from Mounting on
page 2.
Photocell Control
Cat. No. (See right)
l No Option≠
SAR
The Archetype®
revision 04/08/15 • kl_ sarhid_spec.pdf
Convex Glass Lens
Cat. No. l CGL
l No Optionˇ
The F" thick clear convex tempered glass lens replaces
the standard flat glass lens. Provides increased lens
presence and provides a subtle improvement in
uniformity where pole spacing is extreme. Increases
effectiveness of houseside shielding.
4"
3"
Poly carbonate Lens
Cat. No. l LS
l No Option
Fixture supplied with a one piece vacuum formed,
clear, UV stabilized convex polycarbonate, fully gasket-
ed, replacing the standard tempered glass lens.
CAUTION: Use only when vandalism is anticipated to
be high. Useful life is limited by UV discoloration from
sunlight and metal halide lamps.
2K"
1L"
Wall mount using adapter plate
3" or 4" J-box in wall (by others)^
J-box
SS
S
S
S
1SA 2SB
2SL 3ST, 3SY 4SC
Mounting Configuration:
S – Fixture with Photocell Sensor
S – slave unit(s)
No fixture wattage limit.e
s
s
s s s s
s
Photocell Sensor
Cat. No. Line Volts:
l A-30 120V
l A-31 208V
l A-32 240V
l A-33 277V
l A-35 347V
l A-34 480V
Fixture supplied with an internal photocell with
the sensor on the fixture end facing the pole. For multi-
ple-fixture pole mountings, one fixture has a photocell
to operate the others. Not available if wall mounted
(1W).
© 2015 KIM LIGHTING • 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
Type:
Job:
Optional Features
Convex Glass Lens
Polycarbonate Lens
Quartz Standby
Cat. No. l QS
l No Option
Integral electronic device energizes a T-4 mini-can socket during
initial lamp start-up or after a power interruption. De-energizes
prior to HID lamp reaching full brightness. T-4 halogen lamp by
others; 100 watt maximum.
Horizontal Slipfitter Mount
Cat. No. l HSF
l No Option
Page: 4 of 5
Replaces standard mounting arm with a slipfitter which
allows fixture to be mounted to a horizontal pole davit-
arm with 2" pipe-size mounting end (2C" O.D.). Cast
aluminum slipfitter with set screw anti-rotation lock.
Bolts to housing from inside the electrical compartment
using mounting holes for the standard support arm.
Davit-arm must be field drilled at a set screw location to
insure against fixture rotation. Finished to match fixture
and arm.
Horizontal Slipfitter
Mount by Kim
Davit-arm with 2" pipe-size
fixture mount (by others)
Standard die-cast latch is provided with a captive 10-32
stainless steel flat socket-head screw to prevent unau-
thorized opening.
NOTE: Required only for vandal protection in locations
where fixtures can be reached by unauthorized persons.
© 2015 KIM LIGHTING • 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
Tamper-Resistant Latch
Cat. No. l TL
l No Option
SAR
The Archetype®
revision 04/08/15 • kl_ sarhid_spec.pdf
(Types II, III, and IV only) Fixtures with the standard
flat glass lens are available with stamped aluminum
louvers that pass streetside light and block houseside
light, and a blackened panel added to the reflector to
reduce houseside reflections. Fixtures with the optional
convex glass lens are available with a formed aluminum
shield that passes streetside light and blocks houseside
light, and a black anodized panel added to the reflector
to reduce houseside reflections. Use with clear lamps
only, as coated lamps reduce effectiveness.Ü
Houseside Shield
Cat. No. (See right)
l No Option
Cat. No.
l HS
l HSC
Recommended for use with clear lamps only. Effectiveness is reduced for
coated lamps. Not for use with Type V light distributions.
For use with all fixtures with convex glass lens. Not for use with Type V light
distributions.
HS
for flat lens
HSC
for convex lens or
polycarbonate lens
Type:
Job:
Optional Features
Tamper-Resistant Latch
Neighbor Friendly Shield
Cat. No. l NFS
l No Option
(Type IV only) Stamped internal shield and blocking
panels are used to direct and redirect lighting into a
forward throw distribution. The amount of light directed
and redirected toward the back of the liminaire is
dramatically reduced to create extremely low glare
behind the pole. Only available on the Type IV reflectors.hNFS
Vertical Slipfitter Mounts
Cat. No. includes Mounting
Cat. No. (See right)
l No Option
Page: 5 of 5
Vertical
Slipfitter
Mount
by Kim
Pole with 2" pipe-size
tenon (by others)
Allows fixture with standard support arm to be mounted
to poles having a 2" pipe-size tenon (2C" O.D. x 4K"
min. length). All mounting configurations can be used
(1SA, 2SB, 2SL, 3ST, 3SY, 4SC). 4" square or round
die-cast aluminum with flush cap, secured by four C"
stainless steel set point allen screws, finished to match
fixture and arm.
NOTE: 3SY only available on round slipfitter.
SAR
The Archetype®
revision 04/08/15 • kl_ sarhid_spec.pdf
© 2015 KIM LIGHTING • 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
Cat. No.
l VSF-1SA
l VSF-2SB
l VSF-2SL
l VSF-3ST
l VSF-3SY
l VSF-4SC Square
Round
Cat. No. Mounting Configuration
l SVSF-1SA 1SA - single arm mount
l SVSF-2SB 2SB - 2 at 180°
l SVSF-2SL 2SL - 2 at 90°
l SVSF-3ST 3ST - 3 at 90°
3SY - 3 at 120°
l SVSF-4SC 4SC - 4 at 90°
Stainless
steel set
screws
Type:
Job:
Optional Features
