Kl Wc14 Spec
2012-02-01
: Pdf Kl Wc14 Spec kl_wc14_spec spec products kim
Open the PDF directly: View PDF 
.
Page Count: 5
| Download | |
| Open PDF In Browser | View PDF |
Reset Form WC14 14" Wall Commander® revision 7/19/11 • kim_wc14_spec_.pdf Type: Job: Catalog number: Fixture Approvals: / / / Electrical Module Finish Options See pages 3-4 See page 2 Specifications 50 to 150 watt Medium Base Lamps 19" (482.6 mm) 13C" (339.7 mm) 12N" (319.1 mm) Top 5N" (141.3 mm) Front 5N" (141.3 mm) Side Bottom 2D" (66.7 mm) to J-box center Back 5" (127.0 mm) Date: Page: 1 of 5 Housing and Lens The complete housing fastens to a mounting plate with keyhole slots freeing both hands for securing and wiring. Access to field splice is through back of housing. For UP and UP/DOWN model: One-piece die-cast, low copper (<0.6% Cu) aluminum alloy. Lens (Up model) and top lens (Up/Down model) is flat F" thick tempered glass mounted flush with top of housing for water run off, and is silicone sealed. For DOWN model: Two-piece die-cast, low copper (<0.6% Cu) aluminum alloy. Top of housing is closed with a die-cast plate with cooling fins to dissipate heat. The top plate is secured by fasteners and sealed with silicone gasketing around the perimeter. Access Door (UP model): One-piece die-cast, low copper (<0.6% Cu) aluminum alloy with integral stainless steel pin hinges. Two stainless steel thumb latches secure the frame to the housing. Lens Frame (DOWN and UP/DOWN model): One-piece die-cast, low copper (<0.6% Cu) aluminum alloy with integral stainless steel pin hinges. Two stainless steel thumb latches secure the frame to the housing. Sealing is provided by a one-piece molded silicone gasket between the glass lens and the reflector flange. Clear flat lens is F" thick tempered glass secured to lens frame with retainer clips. Reflector Module All sockets are procelain medium base rated 4KV. All models are factory prewired with quick-disconnect plug for mating to the ballast module. For all models: Specular Alzak® optical segments rigidly mounted within a die-cast aluminum enclosure that attaches to the housing by stainless steel hinge and latches. The Wall Grazer and Spot systems include black louver vanes that run parallel to the lamp arc for controlling the hot spot directly behind the luminaire, and the spill light into the atmosphere. Electrical Module: High power factor ballasts are mounted to a rigid aluminum tray and secured to the housing with screws and key hole slots. Factory prewired with quick-disconnect plugs for mating to the reflector module and incoming leads. Mounting Plate: Mounting plate attaches directly to any standard 4" junction box. All mounting plates are die-cast aluminum with reinforced ribs. Two studs are provided in each plate with flange nuts to allow luminaire mounting by key hole slots. Sealant must be applied (by others) between mounting plate and mounting surface to ensure a dry junction box. Finish/Color: Finish is Super TGIC thermoset polyester powder coat paint, 2.5 mil nominal thickness, applied over a titanated zirconium conversion coating; A.S.T.M. 2500 hour salt spray ™ test endurance rating. Standard colors are Black, Dark Bronze, Light Gray, Stealth Gray , Platinum Silver, or White. Custom colors are available. CAUTION: Fixtures must be grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in serious personal injury. 11D" (295.3 mm) WC14 Mounting Plate Attaches directly to any standard 4" J-box (by others) Listings and Ratings UL cUL 1598 1 CE IP66 Rated 25C Ambient 1 Suitable for wet locations KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE. © 2011 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695 WC14 14" Wall Commander® revision 7/19/11 • kim_wc14_spec_.pdf Type: Job: Page: 2 of 5 Standard Features Fixture Cat. No. designates WC14 fixture with: = Up Light Distribution = Down Light Distribution n/a = not available Type III Type II s Type IV t s Type UP ONLY II WC14U2 DOWN ONLY t Type II WC14D2 s Type UP / DOWN II s Type III WC14U3 t Type III WC14D3 s Type III s Type IV WC14U4 t Type IV WC14D4 s Type IV Primary and Secondary Grazers Primary and Secondary Spots Primary Grazer Primary s Spot WC14UG WC14US Primary Grazer Primary t Spot WC14DG WC14DS s t Secondary s Grazer Secondary s Spot Asymmetric Flood s Asymmetric Flood Ray s n/a AsymmetricFlood t n/a t n/a s Asymmetric Flood Ray Ray n/a s Ray1 ,2 t Type II n/a n/a n/a WC14UGD2 WC14USD2 WC14UFD2 WC14URD2 t Type III n/a n/a n/a WC14UGD3 WC14USD3 WC14UFD3 WC14URD3 t Type IV n/a n/a n/a WC14UGD4 WC14USD4 WC14UFD4 WC14URD4 Secondary t Grazer 2 Secondary t Spot 2 t Asymmetric Flood WC14U2DG WC14U3DG WC14U4DG WC14UGDG WC14USDG WC14UFDG WC14URDG WC14U2DS WC14U3DS WC14U4DS WC14UGDS WC14USDS WC14UFDS WC14URDS WC14U2DF WC14U3DF WC14U4DF WC14UGDF WC14USDF WC14UFDF WC14URDF For colored up light ray beam, contact factory. Primary grazer or primary spot optics supplied when specified with the ray option. Secondary grazer or secondary spot optics supplied when specified in all other up/down combination configurations 1 2 Refer to the Kim Lighting Wall Commander Catalog for a complete matrix of available configurations. © 2011 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695 WC14 14" Wall Commander® revision 7/19/11 • kim_wc14_spec_.pdf Type: Job: Page: 3 of 5 Standard Features Electrical Module PMH=Pulse Start Metal Halide HPS=High Pressure Sodium IF = Induction Fluorescent PL = Compact Fluorescent Triple Tube Cat. Nos. for Electrical Modules available: Pulse Start Metal Halide 50PMH120 50PMH208 50PMH240 50PMH277 50PMH347 Lamp ED-17, Clear Socket Medium Base ANSI Ballast M-148 / M-110 High Pressure Sodium 70HPS120 70HPS208 70HPS240 70HPS277 70HPS347 70HPS4803 Lamp ED-17, Clear Socket Medium Base ANSI Ballast S-62 70PMH120 70PMH208 70PMH240 70PMH277 70PMH347 70PMH4803 100PMH120 100PMH208 100PMH240 100PMH277 100PMH347 100PMH4803 150PMH120 150PMH208 150PMH240 150PMH277 150PMH347 150PMH4803 T6 ED-17, Clear G-12 Medium Base M-143 / M-98 ED-17, Clear Medium Base M-140 / M-90 T6 ED-17, Clear G12 Medium Base M-142 / M102 100HPS120 100HPS208 100HPS240 100HPS277 100HPS347 100HPS4803 150HPS120 150HPS208 150HPS240 150HPS277 150HPS347 150HPS4803 ED-17, Clear Medium Base S-54 ED-17, Clear Medium Base S-55 Compact Fluorescent Triple Tube 42PL1201 42PL2081 42PL2401 42PL2771 Lamp Coated Socket GX24q-4 Base ANSI Ballast 57PL1201, 2, 4 57PL2081, 2, 4 57PL2401, 2, 4 57PL2771, 2, 4 Coated GX24q-5 Base Lamp Lamp Line Watts Type Volts 150 PMH 277 Induction Fluor. 55IF1204 55IF2084 55IF2404 55IF2774 Induction Fluor. Multiple CFL lamp configurations (ie, two 42W lamps) are possible with certain optical systems. Consult factory for details. Remote battery pack and test switch available for 57W CFL lamps - consult factory. “EM” option not available with 55W IF lamps. 3 480 volt with medium base lamp sockets may require approval by the local building code authority. 4 For Type II, Type III, or Type IV fixtures only. Up or down. NOTE: Lamp and electrical data supplied for reference purposes only. All initial lumen values shown may vary from one manufacturer to another. Consult lamp manufacturer’s data for exact lumen and life data. CAUTION: All manufacturers of metal halide lamps recommend turning them off for 15 minutes once per week when under continuous operation. This will reduce the risk of arc tube rupture at end of life. Also, color temperature may differ between manufacturers of metal halide lamps. See lamp manufacturers’ specification sheets. WARNING: Fixtures must be installed and grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in serious personal injury. For lamp/ballast information outside of the U.S.A. and Canada, please consult our local Kim representative. Lamps by others. 1 2 Black Dark Bronze Light Gray Stealth Gray™ Platinum Silver White Custom Color5 Color: Finish Super TGIC powder coat paint Cat. No.: BL DB LG SG PS WH CC over a titanated zirconium 5 Custom colors subject to additional charges, minimum quantities and extended lead times. conversion coating. Consult representative. Custom color description: © 2011 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695 WC14 14" Wall Commander® revision 7/19/11 • kim_wc14_spec_.pdf Type: Job: Page: 4 of 5 Optional Features Base Socket Cat. No. G12 No Option Available for 70W and 150W Pulse Start Metal Halide lamps only. Photocell Control Factory installed inside housing with fully gasketed sensor on side wall. Cat. No. (see right) No Option Lexan® non-yellowing enclosure Cat. No. WC14LS No Option Wire Guard Cat. No. WC14WG No Option Fusing Cat. No. (see right) No Option Quartz Standby Cat. No. QS No Option Houseside Shield Cat. No. HS No Option Cat. No. A-30 A-31 A-32 Line Volts: 120V 208V 240V Cat. No. A-33 A-34 A-35 Line Volts: 277V 480V 347V F" clear convex vacuum formed non-yellowing Lexan® enclosure with gasket. Mounts over lens to predrilled door frame holes. NOTE: Catalog number is for one enclosure. Order 2 enclsoures for both up and down distributions For use with all WC14 fixtures, UP or DOWN. 11 ga. (.12" dia.) BB Wire. (.75" sq. welded mesh pattern.) Finish is Super TGIC thermoset polyester powder coat paint, over zinc plated wireform. Finished to match the fixture. Only available with flat lens applications. NOTE: Catalog number is for one wire guard. Order 2 wire guards for both up and down distributions. WG14 = 11C" x 10J" x 1K" deep Photocell Control Lexan® Enclosure Wire Guard High temperaure fuse holders factory installed inside the fixture housing. Fuse is included. Line Volts: 120V Cat. No.: SF 208V 240V 277V DF DF SF 347V SF 480V DF Integral electronic device energizes a T-4 mini-can socket during initial lamp start-up or after a power interruption. De-energizes prior to HID lamp reaching full brightness. T-4 halogen lamp by others; 100W maximum. Up or down shield for Type II, III, and IV area optics only. Combination louver shield and black end-panel for reflector. Factory installed to reflector module. Reduces light toward wall. CAUTION: Do not use the houseside shield option with the grazer or spot as it will interfere with the light distribution. © 2011 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695 Single Fuse Quartz Standby Houseside Shield WC14 14" Wall Commander® revision 7/19/11 • kim_wc14_spec_.pdf Type: Job: Page: 5 of 5 Optional Features L" conduit holes Direct Conduit Entries Cat. No. DCE No Option Two conduit locations provided on the housing, (1) on the side wall and (1) on top of housing for L" conduit clearance. Emergency Battery Back-up Cat. No. EM No Option Internal battery pack provides 90 minutes of supplemental light at 750 lamp lumens on 42 watt compact fluorescent lamps only. Remote mounted battery pack also available for 57W CFL - consult factory. Color Ray Kits Each color ray kit includes (5) glass tile pieces, except for the multi-color kit which includes (5) of each color plus (5) clear, (30 pieces total). Color: Amber Blue Green Red Yellow Multi-Color Cat. No.: CRA CRB CRG CRR CRY CRM battery back-up Single or multi-color ray kits available. NOTE: Ray colors and distributions may vary with reflector types, sources, and color temperatures. Not recommended for all lamp types. Contact factory for more information. Easy and Flexible Field Installation: Simply arrange the color glass tiles into the slide channel and replace the retaining pin. Secure the reflector assembly back into the housing and latch the lens frame shut. Wall Commander reflector assembly with ray option © 2011 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Mode : UseThumbs XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:08:23 Producer : Acrobat Distiller 4.0 for Macintosh Create Date : 1999:09:09 11:21:15Z Modify Date : 2011:07:20 09:58:55-07:00 Metadata Date : 2011:07:20 09:58:55-07:00 Creator Tool : QuarkXPress(tm) 4.04 Document ID : uuid:df8e3874-c4b0-4adb-b46a-521f1fb22496 Instance ID : uuid:267745d1-8092-4f53-95de-4cf8e5e68a6b Format : application/pdf Creator : Title : Has XFA : No Page Count : 5 Page Layout : SinglePage Author :EXIF Metadata provided by EXIF.tools