User´s Guide: BNI EIP 502 105 R015 / 508 EN Manual

User Manual: Pdf

Open the PDF directly: View PDF .
Page Count: 54

Download
Open PDF In Browser	View PDF

BNI EIP-502-105-R015
BNI EIP-508-105-R015
EtherNet/IP™ IP67 modules
User's Guide

Table of Contents

Notes
1.1. Structure of the guide
1.2. Typographical Conventions
Enumerations
Actions
Syntax
Cross-references
1.3. Symbols
1.4. Abbreviations
1.5. Deviating views

3
3
3
3
3
3
3
3
3
3

Safety
2.1. Intended Use
2.3. General Safety Notes
2.4. Resistance to Aggressive Substances
Dangerous Voltage

4
4
4
4
4

First Steps
3.1. Module Overview
3.2. Mechanical Connection
3.3. Electrical Connection
Power Supply
Grounding
Ethernet IP Interface
I/O Port
IO-Link Port
Port

5
5
6
6
6
6
6
7
7
7

Technical Data
4.1. Dimensions
4.2. Mechanical Data
4.3. Operating Conditions
4.4. Electrical Data
4.5. Ethernet
4.6. Function Indicators
Module Status
Port

8
8
8
8
8
9
9
9
10

Integration
5.1. Integration in Rockwell RS Logix 5000
5.2. Address Specifications
5.3. Data Configuration
5.4. Configuration Data
Module Configuration BNI EIP-502-105-XXX
Module Configuration BNI EIP-508-105-XXX
Module Configuration BNI EIP-507-005-Z040, BNI EIP-527-005-Z040
Module Configuration BNI EIP-508-XXX-XXXX-C06
IO-Link Port Configuration
Cycle Settings
Validation Settings
Parameter Server
Upload Flag on the IO-Link Device

11
11
15
15
15
16
16
16
16
17
18
18
19
19

Configuration via Explicit Messages
QuickConnect
Rockwell Automation Products that are Compatible with QuickConnect

www.balluff.com

20
20
21

Balluff Network Interface EtherNet/IP™

Example with Rockwell Components
PLC Program
Fault State
Enable/Disable Fault State
Fault State Action
IO-Link Device Parameterization
Read IO-Link Parameter
Write IO-Link Parameter

22
23
26
26
26
27
27
29

Process Data
7.1. Process Data Inputs
Standard Input Data
IO-Link Input Data
7.2. Process Data Outputs
Standard Output Data
IO-Link Output Data

30
30
30
31
32
32
32

Display
8.1. General
8.2. Address Specifications
8.3. Control and Display
8.4. Display Information
8.5. Design and Symbols
8.6. Startup
8.7. Main Menu
8.8. IP Setup
8.9. Network Config
8.10. Edit mode
8.11. Module Information
8.12. General Information

33
33
33
33
33
34
34
34
35
35
36
37
37

Web Server
9.1. General
9.2. Navigation / Info
9.3. Login/Logout
9.4. "Home" dialog
9.5. "Ports" dialog
No appropriate IODD uploaded
Appropriate IODD uploaded
9.6. "IODD" dialog
9.7. "Config" dialog
9.8. "Log" dialog

38
38
39
40
41
43
43
44
46
47
49

Appendix
10.1. Scope of Delivery
10.2. Order Number
10.3. Ordering Information

51
51
51
51

Notes

www.balluff.com

Notes

1.1. Structure of the
guide

This guide is arranged so that one chapter builds upon the other.
Chapter 2: Basic safety instructions
Chapter 3: Main steps for installing the device
………

1.2. Typographical
Conventions

The following typographical conventions are used in this manual.

Enumerations

Enumeration is shown in the form of bulleted lists.
•
Entry 1,
•
Entry 2

Actions

Action instructions are indicated by a preceding triangle. The result of an action is indicated
by an arrow.
 Action instruction 1.
 Result of action.
 Action instruction 2.
Actions can also be indicated as numbers in parentheses.
(1) Step 1
(2) Step 2

Syntax

Numbers:
Decimal numbers are shown without additional information (e.g. 123),
Hexadecimal numbers are shown with the additional indicator hex (e.g., 00 hex) or the prefix
"0x" (e.g., 0x00).

Cross-references

Cross-references indicate where additional information on the topic is located.

1.3. Symbols

Note
This symbol indicates general notes.
Attention!
This symbol indicates a security notice which most be observed.

1.4. Abbreviations

BNI
I
EIP
EMC
FE
O

1.5. Deviating views

Product views and illustrations in this manual may differ from the actual product. They are
intended only as illustrative material.

www.balluff.com

Balluff Network Interface
Standard input port
EtherNet/IP™
Electromagnetic compatibility
Function ground
Standard output port

Balluff Network Interface EtherNet/IP™

Safety

2.1. Intended Use

2.2. Installation and
Startup

2.3. General Safety
Notes

2.4. Resistance to
Aggressive
Substances

Dangerous
Voltage

The BNI EIP-… is a decentralized IO-Link, input and output module for connecting to the
EtherNet/IP™ network.
Attention!
Installation and startup are to be performed by trained technical personnel only.
Skilled specialists are people who are familiar with the work such as installation
and the operation of the product and have the necessary qualifications for these
tasks. Any damage resulting from unauthorized tampering or improper use shall
void warranty and liability claims against the manufacturer. The operator is
responsible for ensuring that the valid safety and accident prevention regulations
are observed in specific individual cases.
Commissioning and inspection
Before commissioning, carefully read the User's Guide.
The system must not be used in applications in which the safety of persons depends on the
function of the device.
Intended use
Warranty and liability claims against the manufacturer shall be rendered void by damage
from:
•
Unauthorized tampering
•
Improper use
•
Use, installation or handling contrary to the instructions provided in this User's
Guide.
Obligations of the owner/operator
The device is a piece of equipment in accordance with EMC Class A. This device can
produce RF noise. The owner/operator must take appropriate precautionary measures
against this for its use. The device may be used only with a power supply approved for this.
Only approved cables may be connected.
Malfunctions
In the event of defects and device malfunctions that cannot be rectified, the device must be
taken out of operation and protected against unauthorized use.
Intended use is ensured only when the housing is fully installed.
Attention!
The BNI modules always have good chemical and oil resistance. When used in
aggressive media (such as chemicals, oils, lubricants and coolants, each in a high
concentration (i.e. too little water content)), the material must first be checked for
resistance in the particular application. No defect claims may be asserted in the
event of a failure or damage to the BNI modules caused by such aggressive
media.
Attention!
Before working on the device, switch off its power supply.
Note
In the interest of continuous improvement of the product,
Balluff GmbH reserves the right to change the technical data of the product and
the content of these instructions at any time without notice.

www.balluff.com

First Steps

3.1. Module Overview
17

1
2

5
14

6
7

Figure – Overview: BNI EIP-508-105-R015
1
2
3
4
5
6
7
8
9

www.balluff.com

Mounting hole
EtherNet/IP™ port 2
Display
Power supply, input
Status LED: communication / module
Port 08 / 09 (IO-Link, standard I/O)
Pin/port LED: signal status
Port 10 / 11 (IO-Link, standard I/O)
Port 12 / 13 (IO-Link, standard I/O)

10
11
12
13
14
15
16
17

Port 14 / 15 (IO-Link, standard I/O)
Port 06 / 07 (IO-Link, standard I/O)
Port 04 / 05 (IO-Link, standard I/O)
Port 02 / 03 (IO-Link, standard I/O)
Port 00 / 01 (IO-Link, standard I/O)
Power supply, output
EtherNet/IP™ port 1
Ground connection

Balluff Network Interface EtherNet/IP™

First Steps

3.2. Mechanical
Connection

The module is secured by means of two M6 screws and two washers.
Insulation support is available separately.

3.3. Electrical
Connection
Power Supply

7/8”, male

Function

+24 V

Actuator supply

+24 V

Module / sensor supply

OUT

Description

GND module / sensor and actuator supply

7/8” female

Note
Where possible, use a separate power source to supply the sensor/bus and
actuator with power.
Total current < 9 A The total current of all modules must not exceed 9 A even in
the case of series connection of the actuator supply.
Grounding

Note
The functional ground connection between housing and machine must have a
low impedance and be as short as possible.
Ethernet IP
Interface

www.balluff.com

M12, D-coded, female
Pin
1
2
3
4

Tx+
Rx+
TxRx-

Function
Transmit Data +
Receive Data +
Transmit Data Receive Data -

First Steps

I/O Port

M12, A-coded, female
Pin
1
2
3
4
5

Function
+24 V, 200 mA
Input/output 2A
GND
Input/output 2A
FE

Note
For the digital sensor inputs, refer to guideline on inputs EN 61131-2, Type 2.
Note
The total current of the module must not exceed 9 A.
Note
Unused I/O ports must be provided with cover caps to comply with degree of
protection IP67.
IO-Link Port

M12, A-coded, female
Pin
1
2
3
4
5

Function
+24 V, 1.6 A
Input/output 2A
GND
IO-Link/input/output 2A
n.a.

Port

BNI EIP-502-105-R015
BNI EIP-508-105-R015

www.balluff.com

Port
00/01, 02/03, 08/09, 10/11 04/05, 06/07, 12/13, 14/15
IN / OUT
IN / OUT / IO-Link
IN / OUT / IO-Link

Balluff Network Interface EtherNet/IP™

Technical Data

4.1. Dimensions

4.2. Mechanical Data

4.3. Operating
Conditions

4.4. Electrical Data

www.balluff.com

Housing material

Plastic housing, resistant (Fortron 6165 A6 black)

Enclosure rating per IEC 60529

IP 67 (only when plugged-in and threaded-in)

Supply voltage

7/8" 4-pin, connector / female

Input ports / output ports

M12, A-coded (8x female)

Dimensions (W x H x D in mm)

68 x 226 x 42.9

Type of mounting

Screw mounting with 2 mounting holes

Ground strap installation

Weight

Approx. 670 gr.

Operating temperature Ta
Storage temperature

-5 °C ... 70 °C
-25 °C ... 70 °C

EMC
- Immunity
- Emission

EMC Directive 2004/108/EEC
- EN 61000-6-2
- EN 61000-6-4

Shock/vibration

EN 60068-2-6, EN 60068-2-27
EN 60068-2-29, EN 60068-2-64

Supply voltage

18...30.2 V DC, in accordance with EN 61131-2

Ripple

< 1%

Input current at 24 V

130 mA

Technical Data

4.5. Ethernet

Ethernet IP port

2 x 10Base/100Base Tx

Connection for Ethernet IP port

M12, D-coded, female

Cable types in accordance with
IEEE 802.3

Shielded, twisted pair min. STP CAT 5/ STP CAT 5e

Data transmission rate

10/100 Mbps

Max. cable length

100 m

Flow control

Half-duplex/full-duplex (IEEE 802.33x pause)

4.6. Function
Indicators

Status LEDs

Port LEDs

Module Status

LED
UA
US

Mod

Netw
ork

100
LNK

www.balluff.com

Display
Green
Red, flashing
Red
Green
Red, flashing
Green, flashing
Green
Red, flashing
Red-green, flashing
Off
Green, flashing
Green
Red, flashing
Red-green, flashing
Off
Yellow
Green

Description
Output power OK
Low output power (< 18V)
No output power (< 11V)
Input power OK
Low input power (< 18V)
Incorrect or no configuration of the module
Module is working
Fixed bus clock is not possible
Initial sequence
Module has no IP address
Module has IP, but no connection established
Connection established
Connection timeout
Initial sequence
Bus clock: 10 Mbps
Bus clock: 100 Mbps
Data transfer

Balluff Network Interface EtherNet/IP™

Technical Data

Port

Each port has two bicolored LEDs for displaying the I/O statuses.

IO-Link port

I/O port

Display

www.balluff.com

Status

Description

Off

I/O status

The status of the input or output pins is 0

Yellow
Red,
flashing
Red

I/O status

The status of the input or output pins is 1

Short-circuit

Short-circuit between pin 1 and 3

Short-circuit

Short-circuit at dedicated pin

Green
Green,
flashing
Green,
rapidly
flashing
Red
Red,
flashing
quickly

IO-Link

IO-Link communication active

IO-Link

No IO-Link communication

IO-Link

IO-Link pre-operate during data storage

Short-circuit

Short-circuit at pin 4
Validation failed /
Data storage failed /
Wrong device for data storage

IO-Link

Integration

5.1. Integration in
Rockwell RS
Logix 5000

Here you see an example of how the module can be integrated into a Rockwell RS Logix
5000:
First go offline

Right-click Ethernet (on the correct scanner card)
Select a new module

www.balluff.com

Balluff Network Interface EtherNet/IP™

Integration

Then select the general Ethernet module as the ETHERNET module in the communication
path

Now enter a user-defined tag name to select the general format Data-SINT, to enter the IP
address of the module and to enter the correct connection parameters.

www.balluff.com

Integration

The new module and corresponding controller tags are generated automatically.

Then download the configuration

www.balluff.com

Balluff Network Interface EtherNet/IP™

Integration

When the download is done, you can observe and control the tags using the Controller Tags option. Make
sure you select the correct tag name, which you configured beforehand.
The input, output and configuration data for this is described on the following pages.
You can use these tags for the programming, too.

www.balluff.com

Integration

5.2. Address
Specifications

These settings are factory-set.
IP-Adresse:
192.168.1.1
Subnetmaske:
255.255.255.0
Gatewayadresse: 192.168.1.1

5.3. Data
Configuration

Please enter the following values in the control system. They describe the data sizes of the
input, output and configuration data.
Instanc ID
Input
Output
CONFIG

5.4. Configuration
Data

100
101
102

502
200
134
98

508
392
262
194

Data length
507
196
130
98

527
196
128
98

508-C06
128
86
0

The following tables show an allocation of the configuration data sequence. The standard
values specified below describe a configuration with the IO-Link function at Pin 4 and
standard I/O functions at Pin 2 and 4 of each port. The input and output functions of the
configured standard I/O ports are set via the process data.
BNI EIP-502-105-XXXX, BNI EIP-507-005-Z040, BNI EIP-527-005-Z040
Slot
1
2
3
4
5

Byte
0…1
2…25
26…49
50…73
74…97

Module part
Module
IO-Link port 0
IO-Link port 1
IO-Link port 2
IO-Link port 3

Description
General configuration for the entire module
Configuration of IO-Link port 0
Configuration of IO-Link port 1
Configuration of IO-Link port 2
Configuration of IO-Link port 3

BNI EIP-508-105-XXXX
Byte
0…1
2…25
26…49
50…73
74…97
98…121
122…145
146…169
170…193

Slot
1
2
3
4
5
6
7
8
9

Module part
Module
IO-Link port 0
IO-Link port 1
IO-Link port 2
IO-Link port 3
IO-Link port 4
IO-Link port 5
IO-Link port 6
IO-Link port 7

Description
General configuration for the entire module
Configuration of IO-Link port 0
Configuration of IO-Link port 1
Configuration of IO-Link port 2
Configuration of IO-Link port 3
Configuration of IO-Link port 4
Configuration of IO-Link port 5
Configuration of IO-Link port 6
Configuration of IO-Link port 7

Note
The BNI EIP-508-XXX-XXXX-C06 has no configuration data. These are fixed
and can not be changed.

www.balluff.com

Balluff Network Interface EtherNet/IP™

Module
Configuration
BNI EIP-508-105XXX

Module
Configuration
BNI EIP-507-005Z040, BNI EIP527-005-Z040

www.balluff.com

Description
3

Port function
0x00: Standard I/O
0x01: IO-Link

Bit

Module
Configuration BNI
EIP-508-XXXXXXX-C06

Bit
7

Byte

Module
Configuration
BNI EIP-502-105XXX

Byte

Integration

Byte

Port function
0x00: Standard I/O
0x01: IO-Link

Bit
7

6
P3

Description
3

2
P1

Reserved

0
P0

Port function
0x00: Standard I/O
0x01: IO-Link

The IO-Link ports are always activated.

Integration

IO-Link Port
Configuration

Byte

6
Basic

Description
3

2
Time

Validation type

4
5
6
7
8
9
…
24

Vendor ID 1
Vendor ID 2
Device ID 1
Device ID 2
Device ID 3
Serial number 1
…
Serial number 16

…

www.balluff.com

Bit
7

0
Cycle time
Validation type
0 No validation
1 compatible (VID + DID)
2 Identical (VID + DID + SerNum)
Vendor ID
Device ID

Serial number

Parameter server
0x8X Enable
0x0X Disable
Parameter server
0x40 Delete
0xX1 Enable upload
0xX2 Disable download
The data of the other IO-Link ports is structured identically and described in the following.
For the BNI EIP-508-xxx-xxxx-C06 these data are not adjustable.

Balluff Network Interface EtherNet/IP™

Cycle Settings

This parameter can be used to influence the IO-Link communication speed. Calculated
using the multiplier and the time base, the IO-Link cycle time can be increased.
The time base is described in Table B3. The multiplier is entered in decimal form from
0…63.
Bit
7

Time
base

Description
3

Multiplier

0
Bit 0 to 5: Multiplier
These bits contain a 6-bit multiplier for the
calculation of MasterCycleTime or MinCycle
Time. Permissible values for the multiplier
are
0 to 63.
Bit 6 to 7: Time Base
These bits specify the time base for the
calculation of MasterCycleTime or
MinCycleTime.

Possible values of MasterCycleTime and MiniCycleTime
Time base
encoding

Time base
value

00
01

0.1 ms
0.4 ms

1.6 ms

Calculation
Multiplier x time base
6.4 ms + multiplier x time base
32.0 ms + multiplier x time base

Cycle time
0.4 ms to 6.3 ms
6.4 ms to 31.6 ms
32.0 ms to 132.8 ms

11
Reserved
Reserved
Reserved
NOTE: The value 0.4 results from the minimum possible transmission time according to
A.3.7.
Validation
Settings

www.balluff.com

No validation: validation deactivated, every device will be accepted.
Compatibility: manufacturer ID and device ID are compared to the IO-Link device data.
Identity: manufacturer ID and device ID and serial number are compared to the
IO-Link device data. The IO-Link communication is only started if there is a match.

Integration

Parameter Server

Enable: data management functions enabled, parameter data and identification data of the
IO-Link device are stored permanently.
Disable: data management functions disabled, stored parameter data and identification
data of the IO-Link device remain stored.
Deleted: data management functions disabled, stored parameter data and identification
data of the IO-Link device are deleted.
Enable upload:
If only the upload is enabled, the master always starts an upload of the parameter data. In
this case, the upload is independent of the upload flag of the IO-Link device. If no data is
stored in the Master Port, an upload likewise takes place. (e.g. after deleting the data or
before the first data upload)
Enable download:
If only the download is enabled, the master always starts a download of the parameter data.
In this case, the download is likewise independent of the upload flag of the IO-Link device.
If no data is stored in the Master Port, however, an upload takes place first. (e.g. after
deleting the data or before the first data upload)
Enable upload and download:
If the upload and download are enabled, different parameter sets are distinguished
depending on the upload flag of the IO-Link device.
If no parameter data is stored in the IO-Link master port, an initial upload takes place. (e.g.
after deleting the data or before the first data upload)
If the upload flag is set on the IO-Link device, an upload of the parameter data always takes
place.
If no upload flag is set and parameter data has already been stored, a download of the
parameter data always takes place.
Note
After the upload of the parameter data, the vendor ID and device ID of the
connected IO-Link device are also still saved until the data records are deleted.
When the connected IO-Link device is started, a validation takes place. Thus, only
an IO-Link device of the same type can be used for the data management.
If an IO-Link device of a different type is to be used, the contents of the parameter
server must be deleted.
The data storage is supported only by IO-Link devices with IO-Link Revision 1.1.

Upload Flag on
the IO-Link
Device

The upload flag is needed to overwrite already saved data in the parameter server with new
parameter data of the same IO-Link device.
To enable the upload flag of an IO-Link device,
the data value 0x05 must be entered in the index 0x02, subindex 0.
(For information about configuration via IO-Link, refer to the "Web Server" chapter under
"Device Properties" or the "Configuration via Explicit Messages" chapter
under "IO-Link Device Parameterization")

www.balluff.com

Balluff Network Interface EtherNet/IP™

Configuration via Explicit Messages

QuickConnect

The QuickConnect function makes it faster to boot up and integrate the BNI EIP-50x-105X015 modules.

Enabling QuickConnect automatically takes over all necessary port properties on the module:






Static IP address
Ports at 100 Mbps full-duplex
Auto-negotiation disabled
Auto MDI-X disabled
Prepared for linear topology

You can configure QuickConnect via the following
class instance attribute of the explicit messages:
Class
245 (0xF5)

Instance
1 (0x01)

Attribute
12 (0x0C)

Value
0: disabled (default)
1: enabled

Note
For QuickConnect to be enabled, ACD (Address Conflict Detection) must also be
enabled. This is switched on by default.
The ACD can be reviewed and changed using the following class instance attributes of the
explicit messages:
Class
245 (0xF5)

www.balluff.com

Instance
1 (0x01)

Attribute
10 (0x0A)

Value
0: disabled
1: enabled(default)

Configuration via Explicit Messages

Rockwell
Automation
Products that
are Compatible
with
QuickConnect

Source:
Allen-Bradley Ethernet/IP QuickConnect Application Technique
Page 13

www.balluff.com

Balluff Network Interface EtherNet/IP™

Configuration via Explicit Messages

Example with
Rockwell
Components

Source:
Allen-Bradley Ethernet/IP QuickConnect Application Technique, Page 12
Please also note the following:






www.balluff.com

Direct connection between PLC and QuickConnect slave with crossover cable
Slave-to-slave connection using patch cable
For setting up the topology, only the linear topology with a maximum of 20 modules
on the tool side is permitted.
If needed, only one managed switch may be used between the PLC and Ethernet/IP
slave.
To trigger the QuickConnect sequence, an electrical lock signal is required that
reads in the supply voltage of the QuickConnect slaves via the controller.

Configuration via Explicit Messages

PLC Program

Source:
Allen-Bradley Ethernet/IP QuickConnect Application Technique, Page 29

www.balluff.com

Balluff Network Interface EtherNet/IP™

Configuration via Explicit Messages

Source:
Allen-Bradley Ethernet/IP QuickConnect Application Technique, Page 30

www.balluff.com

Configuration via Explicit Messages

Source:
Allen-Bradley Ethernet/IP QuickConnect Application Technique, Page 31

www.balluff.com

Balluff Network Interface EtherNet/IP™

Configuration via Explicit Messages

Source:
Allen-Bradley Ethernet/IP QuickConnect Application Technique, Page 32
Fault State

A safe state that the port is to take on in the case of a loss of bus communication can be
predefined for each output on the port pins.
The fault state settings can be configured using the following class instance attributes of the
explicit messages.

Enable/Disable
Fault State

Class
9 (0x09)

Instance
1–m

Attribute
6

Value
0: Fault state disabled
1: Fault state enabled

Fault State
Action

Class
9 (0x09)

Instance
1–m

Attribute
5

Value
0: Output on
1: Hold last state

m: Number of outputs
Note
The fault state settings are stored only temporarily in the module. They are deleted
after a power reset.
To ensure a long-term fault state configuration, the configuration has to be
programmed via the PLC so that the settings are transferred to the module again
when the system is restarted.

www.balluff.com

Configuration via Explicit Messages

IO-Link Device
Parameterization

There are two options for configuring an IO-Link device connected to the IO-Link port.


Configuration via the web server
refer to the "Web Server" chapter under "Device Properties"



Configuration via explicit messages

The following example describes how Rockwell RSLogix 5000 devices can be used to
configure an IO-Link device via explicit messages.
For this purpose, the "MSG" components in the PLC program are used.

Read IO-Link
Parameter

Service Code
0x32

Class
0x96

Instance
1-n

Attribute
0x03
(Read Parameter)

n: Number of ports
Source Length must correspond to at least the read parameters, but a larger value can also
be entered. (In this example, 100 bytes)
As the Source Element (Write) and as the Destination Element (Read),
create one SINT[100] array each and select the first line[0].

www.balluff.com

Balluff Network Interface EtherNet/IP™

Configuration via Explicit Messages

In the Source Element Array (Write), enter which index is to be read.
In this example, this is index 0x4E.

Destination Array (Read) shows the read-out value.
In case of a configuration error, the error code is likewise displayed there.
In the "Communication" window, you have to select the Ethernet module
on which the configuration is to take place.

www.balluff.com

Configuration via Explicit Messages

Write IO-Link
Parameter

Service Code
0x32

Class
0x96

Instance
1-n

Attribute
0x02
(Write
Parameter)

n: Number of the ports
Source Element and Destination Element are to be selected so they are identical to the
previous example, "Read IO-Link parameter".
The Source Length must be exactly the same length as the parameter data to be written.
In this example, index 0x4E, subindex 0,
value 0x02 is written in Source Element Array (Write).
In case of a configuration error, an error code appears in Destination Element Array (Read).

In the "Communication" window, you likewise have to select the Ethernet module
on which the configuration is to take place.

Note
The explicit messages functions are implemented in accordance with the
Volume 1: Common Industrial Protocol Specification and
Volume 2: Ethernet/IP Adaption of CIP.

www.balluff.com

Balluff Network Interface EtherNet/IP™

Process Data

7.1. Process Data
Inputs

Standard Input
Data

www.balluff.com

The input data size is 200 bytes. Take a look at the tables below for the allocation of the
process data inputs.
BNI EIP-502-105-R015
Byte
Module part
0…7
Standard I/O ports
8…55
IO-Link port 1
56…103
IO-Link port 2
104…151
IO-Link port 3
152…199
IO-Link port 4

Description
Process data inputs at the standard inputs
Process data inputs at IO-Link port 1
Process data inputs at IO-Link port 2
Process data inputs at IO-Link port 3
Process data inputs at IO-Link port 4

BNI EIP-508-105-R015
Byte
Module part
0…7
Standard I/O ports
8…55
IO-Link Port 0
56…103
IO-Link port 1
104…151
IO-Link port 2
152…199
IO-Link port 3
200…247
IO-Link port 4
248…295
IO-Link port 5
296…343
IO-Link port 6
344…391
IO-Link port 7

Description
Process data inputs at the standard inputs
Process data inputs at IO-Link port 0
Process data inputs at IO-Link port 1
Process data inputs at IO-Link port 2
Process data inputs at IO-Link port 3
Process data inputs at IO-Link port 4
Process data inputs at IO-Link port 5
Process data inputs at IO-Link port 6
Process data inputs at IO-Link port 7

BNI EIP-502-105-R015 and BNI EIP-508-105-R015
Byte

I32

I34

I22

I24

I12

I14

I02

I04

I72

I74

I62

I64

I52

I54

I42

I44

Bit

S0
S4

O32

O34

O22

O24

O12

O14

O02

O04

O72

O74

O62

O64

O52

O54

O42

O44

Description
Input data
I04  Input at port 0, pin 4
The result is 0 only if the port is
configured as an IO-Link port.
Short-circuit status
Short-circuit between pin 1 and 3
at the registered port
Overload status
O04  Overload at port 0, pin 4
Only if the port is configured as an
output.
Status of the power supply
NV: No actuator power supply
PS: Power supply for sensor
PA: Power supply for actuator
Reserved

Process Data

BNI EIP-502-105-R015 and BNI EIP-508-105-R015
Byte

IO-Link Input Data

Bit
7

8
…
39
0

IOL

PDI

55
…

www.balluff.com

IO-Link port 0 input data

42
43
44
45
46
47
48
49
50
51
52
53
54

Description

Mode

Vendor ID 1
Vendor ID 2
Device ID 1
Device ID 2
Device ID 3
Type
Event code high
Event code low
Type
Event code high
Event code low
Type
Event code high

IO-Link status
IOL: Port in IO-Link mode
DC: Device connected
0: Reserved
IO-Link error
VF: Validation failed
SC: IO-Link short-circuit
DF: Data storage validation failed
PDI: Process data invalid
Vendor ID
Device ID

Mode:
0: Reserved
1: Event single shot
2: Event disappears
Mode
0
3: Event appears
Event 2
Type:
0: Reserved
Mode
0
1: Notification
Event 3
2: Warning
Event code low
3: Error
The data of the other IO-Link ports are structured identically and described in the following.
Event 1

Balluff Network Interface EtherNet/IP™

Process Data

7.2. Process Data
Outputs

Standard Output
Data

IO-Link Output
Data

The output data size is 134 bytes. Take a look at the tables below for the allocation of the
process data outputs.
BNI EIP-502-105-R015
Byte
Module part
0…5
Standard I/O ports
6…37
IO-Link port 1
38…69
IO-Link port 2
70…101
IO-Link port 3
102…133
IO-Link port 4

Description
Process data outputs at the standard inputs
Process data outputs at IO-Link port 1
Process data outputs at IO-Link port 2
Process data outputs at IO-Link port 3
Process data outputs at IO-Link port 4

BNI EIP-508-105-R015
Byte
Module part
0…5
Standard I/O ports
6…37
IO-Link Port 0
38…69
IO-Link port 1
70…101
IO-Link port 2
102…133
IO-Link port 3
134…165
IO-Link port 4
166…197
IO-Link port 5
198…229
IO-Link port 6
230…261
IO-Link port 7

Description
Process data outputs at the standard inputs
Process data output at IO-Link port 0
Process data output at IO-Link port 1
Process data output at IO-Link port 2
Process data output at IO-Link port 3
Process data output at IO-Link port 4
Process data output at IO-Link port 5
Process data output at IO-Link port 6
Process data output at IO-Link port 7

Byte

O32

O34

O22

O24

O12

O14

O02

O04

O72

O74

O62

O64

O52

O54

O42

O44

R32

R34

R22

R24

R12

R14

R02

R04

R72

R74

R62

R64

R52

R54

R42

R44

Byte
6…37
…

www.balluff.com

Bit
7

Bit

Description
Output data
O04  Output at port 0, pin 4
To use this function at an IOLink port, the port has to be
configured as an output.
Restart
Restart of the output after a
short-circuit is detected
Reserved
Display control system
DL: Display disabled / PLC
lock
GO: Green display LED
illuminates
RO: Red display LED
illuminates

Description
IO-Link port 0 output data

The data of the other IO-Link ports are structured identically and described in the
following.

Display

8.1. General

With the implemented display, the address is output directly to the devices BNI EIP…
The following address types are possible:
•
IP address
•
Subnet mask
•
Gateway address
Each address is composed of 4 octets.
The display also shows information about the hardware and firmware update.
The display has a locking function that can be enabled from the control panel. If the lock is
set, no more editing can be done (see bit layout, Chapter 6.2 Standard output data).

8.2. Address
Specifications

IP address:
Subnet mask:
Gateway address:

8.3. Control and
Display

192.168.1.1
255.255.255.0
192.168.1.1

IP
SN
GW

↑
3

1 Display
2 Arrow key
3 Octet cursor
8.4. Display
Information

1
2
3

4 Address type cursor
5 "Set" key
6 LED

Cursor for selecting the address type
Cursor for selecting the address type

IP
SN
IP
GW
3

Cursor for selecting the octet
IP: IP address
SN: Subnet address
GW: Gateway address

www.balluff.com

3: First octet
2: Second octet
1: Third octet
0: Fourth octet

Balluff Network Interface EtherNet/IP™

Display

8.5. Design and
Symbols

In the following flow charts, some symbols are used to describe the display functionality:
Current status
Switch
S

Condition: Briefly press the Set key

Condition: Press and hold the Set key (at least 3 seconds)



Condition: Briefly press the arrow key

8.6. Startup
BALLUFF

BALLUFF

BNI
EIP-508105-R015

Module name

VERSION
HW: 1.0
SW: 1.0

Hardware and firmware update

IP
192 . 168 .
015 . 005

Current IP

Subnet
255 . 255 .
255 . 000

Current subnet mask
e

Gateway
000 . 000 .
000 . 000

Current gateway address
8.7. Main Menu

Standard view
4th octet of the IP address

007
S
Network
Config

Menu: Network Config



…

S
Menu: IP Setup

IP
SETUP


…

S
Menu: Module Information

•
•

www.balluff.com

MODULE
INFO



…

Press the Set key briefly to scroll through the main menu.
Press the arrow key to open the menu.

Display

8.8. IP Setup
X STATIC
DHCP
FACTORYSETTING

IP editing mode
S

S
STATIC
DHCP
X FACTORYSETTING

STATIC
X DHCP
FACTORYSETTING



X STATIC
DHCP
FACTORYSETTING


Editing mode
•
•

Press and hold the Set key to call up the editing mode.
The preferred value is configured by briefly pressing the arrow key.

8.9. Network Config

IP
192.168.
015.005



168
S

192

•
•
•
•
•
•

www.balluff.com

000
S

255
S

255

Gateway
000.000.
000.000

Editing mode
Programming mode

005
015



Editing mode
Programming mode

Subnet
255.255.
255.000

000
S

000

000
S

000

Press and hold the Set key to call up the editing mode.
The preferred value is configured by briefly pressing the arrow key.
Press and hold the arrow key to call up the fast program mode.
Briefly pressing the Set key saves the entered value and scrolls to the next octet.
The 4th octet represents the beginning of the editing process.
The completely entered address is saved by briefly pressing the Set key when
editing the first octet. The entered value appears right afterwards in the IP overview
display.
Manual changes to IP, subnet or gateway lead to an automatic change of the IP
setup to "static".

Balluff Network Interface EtherNet/IP™

Display

8.10.

Edit mode

•
•
•
•
•

In the Network Configuration menu, select IP / Subnet or Gateway Address.
Press the set button long to switch to edit mode.
Press the arrow key briefly to change the number.
Press the Set button briefly to move to the next position.
After the last digit, press the set button briefly to move to the next octet of the address
or to accept the new number after the last octet.
Note
The module has to be restarted to work with the new configuration.

www.balluff.com

Display

8.11. Module
Information


BNI
EIP-508105-R015

•
•
8.12. General
Information

•
•
•
•
•
•
•
•



Version
SW: x.x
HW: x.x



MAC ID
XX : XX : XX :
XX : XX : XX

Briefly pressing the arrow key allows scrolling through the "Module information"
menu.
The product name, module updates and Mac-ID are displayed as information.
Press and hold the arrow key to scroll quickly in editing mode.
If no key is pressed for 10 seconds, the view reverts to the standard display (4th
octet of the IP address). Changes that have not been saved will be lost.
Differences between the new configuration and the configuration with which the
module works are indicated by an unequal sign. In this case, the screen switches
to the standard display after 5 seconds.
The display flashes in editing mode. The display flickers in fast scroll mode.
If the module receives a single ping, the word "Ping" appears on the display for a
couple of seconds. Then the previous display returns. You can exit ping mode
sooner by briefly pressing the Set key.
If the module receives two or more pings, the word "Ping" appears on the display.
You can exit the display only by briefly pressing the Set key. Then the display
before the ping returns.
The LED function of the display LEDs can be set in a user-specific manner by
setting several bits in the process data outputs. (see bit layout, standard output
data)
The plc lock function can also be used by setting a bit in the process data outputs.
(see bit layout, standard output data)
Note
You cannot select editing mode in the display if the plc lock is set in the process
data inputs by a bit (see bit layout, standard output data)

www.balluff.com

Balluff Network Interface EtherNet/IP™

Web Server

9.1. General

The BNI fieldbus module contains an integrated web server for retrieving detailed device
information and for configuring the device.
To use the web interface you must first ensure that the module has been correctly integrated
into your network. In addition the IP subnet of the BNI module must be accessible from the
PC on which the browser is running. Please use Internet Explorer 10 or newer as the browser;
older versions may result in display problems.
For open a connection with the web server, enter the IP address of the module in the address
line of the browser. The homepage then appears with the essential device information.

www.balluff.com

Web Server

9.2. Navigation / Info

The navigation bar is located in the upper area of the window, which allows you to switch
between the various dialogs of the web interface. To do this click on the corresponding icon.
When the "Info" tab is selected the following overview appears:

The "BALLUFF" logo at upper right links to the international Balluff homepage.

www.balluff.com

Balluff Network Interface EtherNet/IP™

Web Server

9.3. Login/Logout

To make configuration settings on the fieldbus module using the web interface, you must first
log in. Functionalities which cannot be used without logging in are indicated by the grayed out
buttons.
The default password is:
BNI PNT-XXX-XXX-XXXX
BNI EIP-XXX-XXX-XXXX
BNI ECT-XXX-XXX-XXXX

"BNIPNT“
"BNIEIP“
"BNIECT“

The password cannot be changed!

After successfully logging in the dialogs are shown as follows:

Use the "Logout" button to log out again. After 5 minutes of no interaction with the Webserver
the user is automatically logged out.
Note
For security reasons the fieldbus module shows only one login at a time with
configuration access. Reading (without logging in) is however possible from multiple
PCs at the same time on the fieldbus module.

www.balluff.com

Web Server

9.4. "Home" dialog

Under "Home" you are given the essential information about the fieldbus itself and its network
activity. You are also shown whether the configuration block was enabled by the controller
(PLC).
Information is also shown about the current process data and the status of the module via
the corresponding LEDs. After selecting "LED Legend" a Help dialog appears which explains
the meaning of the LEDs.
If an IO-Link device is connected to one of the configured IO-Link terminals, some of the
device data will be displayed in addition to the module data in the form of a link. After selecting
one of these links the corresponding device dialog is opened.

www.balluff.com

Balluff Network Interface EtherNet/IP™

Web Server

PNT:

EIP:

www.balluff.com

Web Server

9.5. "Ports" dialog

The "Ports" dialog displays information and process data for the connected IO-Link devices.
Select the desired IO-Link Port in the image of the fieldbus module on the right side to see the
device data.
Note
The IO-Link device data are only displayed if the port is also
configured as an IO-Link port!

No appropriate
IODD uploaded

It is possible to read and write the configuration parameters of the IO-Link device via the
"Parameters" option. The parameter indexes and subindexes of the IO-Link device are
described in the corresponding separate user's guide (and follow the IO-Link conventions).
Under "Events" you can see whether a diagnostic event from the IO-Link device exists.
Under "Parameter Server Content" you can view the content of the parameter server if
parameter data is stored on the parameter server.

"Ports" dialog with direct parameter access

www.balluff.com

Balluff Network Interface EtherNet/IP™

Web Server

Appropriate IODD
uploaded

If an IODD appropriate to the IO-Link device connected to the currently selected port has
been uploaded (see "Dialog "IODD"), the normal dialog for "Process Data" and "Parameters"
is not displayed, but rather an expanded dialog.
Information from the IODD of the device is used so that the data can be better understood.
Thus in the following screenshot not only are the input data of the distance sensor displayed
as a hex number, but also interpreted and labeled under "Input".
Since the sensor has no parameters, none are displayed.

Dialog "Ports“: IODD interpretation and device image

www.balluff.com

Web Server

If the IODD of the IO-Link device on the currently selected port has parameters, these are
shown in table format (see following screenshot). In this example the parameters for the Balluff
Smart Light are shown.
The Smart Light is a signal light which can be used in three different modes. These modes can
be set using an IO-Link parameter. The parameter values and associated texts are stored in
the IODD.
This means "Operation Mode" can be read out and displayed ("Read" and "Read All" buttons)
or written to the device ("Write" button).
If subindexes have no buttons they cannot be individually processed but rather only the entire
index at once.
Note
Each changed value must be individually written by clicking on the "Write" button!

"Ports" dialog: Parameter list of an IO-Link device with uploaded IODD

www.balluff.com

Balluff Network Interface EtherNet/IP™

Web Server

9.6. "IODD" dialog

Using this dialog you can transfer IODDs (device description files for IO-Link devices) and the
associated device images to the fieldbus module, so that a detailed representation of the
connected IO-Link devices in the "Ports" dialog is possible.
When IO-Link devices are connected and IO-Link ports are activated, the dialog shows a table
with information about the IO-Link devices.
The fieldbus module file system supports only device names in "8+3" format, i.e. with a
restricted name length. Since IODD files are generally published with a long file name, these
must be renamed and given a shorter naming scheme on the PC before uploading to the
fieldbus module.
For this a help setting is provided in the dialog, with the associated required IODD file name
for the currently connected IO-Link devices shown in the bottom section of the list (column
IODD Filename).
Image files without IODD can also be uploaded; the images are still displayed in the "Ports"
dialog.

Using the "Delete" button you can delete IODDs and device images from the fieldbus when
needed.
Note
Before selecting the IODD it must be renamed on the PC to the file name which is
shown in the table in the "IODD Filename" column!

www.balluff.com

Web Server

9.7. "Config" dialog

The configuration page enables configuration of the module. You can change both the
module information texts and the port configuration.
The "Set Ports" action is not permanently stored in the device and is lost after the next reboot
or reset.
PNT / ECT:

www.balluff.com

Balluff Network Interface EtherNet/IP™

Web Server

EIP:

The parameter set “Module Configuration” on the left side is used by clicking "Save
Configuration" and permanently stored in the device.
The "Reboot" button reboots the device as if the power to the module had been turned off
and on again.
Clicking on "Factory Reset" deletes the configuration and log files saved in the device and
then performs a reboot, so that the device is restored to the default factory configuration as
on delivery.

www.balluff.com

Web Server

9.8. "Log" dialog

This dialog provides general service information about the device as well as a logging
function.
The upper table (see screenshot below) contains important information for all service
inquiries.
Note
If you have a detailed question about a specific situation, send us a screenshot of
this Website or print the site as a PDF.
Logging shows events which have occurred in chronological order. This provides a tool for
detailed troubleshooting in equipment.

www.balluff.com

Balluff Network Interface EtherNet/IP™

Web Server

Events are classified using the "Severity“ column:
Internal Error (Emergency, Alert, Critical)
 The fieldbus module has detected a fault in itself (hardware or software) which should
not occur during normal operation. If this happens, the module must be serviced or
replaced.
External Error (Error, Warning)
 The fieldbus module has detected what may be a non-permissible event which is
affecting the module from the outside. The system may require troubleshooting.
Event (Informational, Notice)
The fieldbus module has detected an important normal operating event and reports it. These
may include for example configuration actions over the web interface and other configuration
interfaces which are also recorded.
Clicking on "Set Module Time” sends the current browser time to the fieldbus module but
does not permanently store it. After a reset, reboot or loss of power the time begins to run
again from the year 2000.
Clicking on "Update Log” refreshes the display, and "Clear Log” deletes all entries. The log
entries are stored in a ring buffer.

www.balluff.com

Appendix

10.1. Scope of
Delivery

The BNI EIP comprises the following elements:
•
IO-Link block
•
4x M12 dummy plugs
•
Ground strap
•
M4x6 screw
•
20 informational signs

10.2. Order Number

BNI EIP-50x-105-R015
Balluff Network Interface
Ethernet IP
Functions
502 = IP 67 IO-Link master module, 4 IO-Link ports
508 = IP 67 IO-Link master module, 8 IO-Link ports
Versions
105 = display version, 2-port switch
Mechanical version
R015 = plastic housing, resistant (Fortron 6165 A6 black)
Data transmission: 2 x M12x1 internal thread
Power supply: 7/8" external thread, 7/8" internal thread
Sensor connections: 8 x M12x1 internal thread

10.3. Ordering
Information

www.balluff.com

Product order code
BNI EIP-502-105-R015
BNI EIP-508-105-R015

Order code
BNI008Z
BNI008M

Notes

www.balluff.com

Balluff GmbH
Schurwaldstrasse 9
D-73765 Neuhausen a.d.F.
Germany
Phone +49 7158 173-0
Fax
+49 7158 5010
www.balluff.com
balluff@balluff.de

No. 922508-726 E 04.124053  Edition D17  Replaces Edition B17 Subject to modification

www.balluff.com

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 54
Language                        : de-DE
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Title                           : User´s Guide: BNI EIP-502-105-R015 / BNI EIP-508-105-R015 EN
Creator                         : Claudia Exner
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2017:05:02 14:49:02+02:00
Modify Date                     : 2017:05:02 14:49:02+02:00
Document ID                     : uuid:88346884-F3E9-4C57-9E5A-F4CC15F12436
Instance ID                     : uuid:88346884-F3E9-4C57-9E5A-F4CC15F12436
Author                          : Claudia Exner

EXIF Metadata provided by EXIF.tools

User´s Guide: BNI EIP 502 105 R015 / 508 EN Manual

Navigation menu

Versions of this User Manual:

Views

Navigation