Mariner
2012-11-11
: Pdf Mariner mariner spec products industrial
Open the PDF directly: View PDF 
.
Page Count: 2
APPLICATIONS
• For use in corrosive, hosedown, marine, shipboard and hazardous environ-
ments. Integrally ballasted luminaire. SFMM Series is for marine applications.
SFM2 Series is for hazardous and marine applications.
SPECIFICATIONS
• Restricted Breathing “RB” option for lower T-Ratings.
•Elevated ambient “EA” options capability up to 65°C.
• “Quick release” lens latches for ease of entry, no screws.
• Luminaire, lens frame, lens latches – 16 gauge 316SS.
• Mounting yoke, safety lens door chains, cord grips (SFMM), conduit hubs
(SFM2) – SS316.
• Mounting accessories are hot dipped galvanized steel.
LISTINGS
• SFMM and SFM2 Listings: UL1598 and 1598A Marine Outdoor.
NEMA 4X; IP66/67
•SFM2 Listings: UL844 Standard: Class I, Division 2 Groups A, B, C, D; Class I,
Zone 2 Groups IIC, IIB, IIA.
ExnR, AxnR Restricted Breathing.
• Type approval American Bureau of Shipping (ABS)
MARINER™
FLOODLIGHT
STAINLESS STEEL FLOOD
HUBBELL INDUSTRIAL LIGHTING SHEET # SFM-SPEC7/10
Industrial Lighting
Cat. #
Job Type
Approvals
ORDERING INFORMATION
ORDERING EXAMPLE: SFM2-40-P-8-EA
A
B
C
10.16"(258.06mm)
DE
Center Hole
0.88" (22.2mm)
2 Holes
0 56"
(14.3mm)
G
H
L
F
K
J
I
ABCDEF
185/16"25
7/32"20
7/32"1
1/2"3
3/32"19
23/32"
465 mm 640 mm 513 mm 39.7 mm 79.5 mm 500 mm
GHI JKL
819/32" 11" 2" 2" 1013/16"4
7/32"
220 mm 279.4 mm 50.8 mm 50.8 mm 274.3 mm 106.3 mm
Series Source OptionsVoltageWattage
- - - -
SERIES
SFMM Stainless Flood Marine
SFM2 Stainless Flood Marine
Class I, Division 2
WATTAGE
15 150W HPS, PS
17 175W PS
25 250W HPS, PS5
40 400W HPS, PS
SOURCE
SHigh Pressure Sodium
PPulse Start (PS) Metal Halide
(lamp included)
VOLTAGE
5480V5
6Tri-Tap®(120/277/347V)
8Quad-Tap®
(120/208/240/277V)
E220/240V, 50 Hz
P220V, 60 Hz
(250, 400W MH only)
OPTIONS
F(X) Fusing (specify voltage)1,2,3
RS Hot Re-Strike (150W HPS)
QS Quartz Standby4
PCR(X) Photo Control1,2,3,4
EA Elevated Ambient (40°C,
55°C, 65°C) capabilities,
see chart for applicable
wattages
RB Restricted Breathing Housing
allowing lower T-Ratings for
SFM2 & SFMH2 Series only.
Fixture provided with test
port entry on side.
1 To denote voltage, replace Xwith 1=120V; 2=208V; 3=240V; 4=277V; 5=480V; 6=347V.
2 Not UL 1598A Marine Listed or CSA listed for hazardous location.
3 CSA certification applicable to Tri-Tap®ballast only.
4 Available in SFMM only. Not suitable for hazardous location.
5 250W Pulse Start not available in 480V or Tri-Tap®.
Copyright © 2010 HUBBELL LIGHTING All Rights Reserved SFM-SPEC7/10 Printed in USA
Hubbell Industrial Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • PHONE: 864-678-1000
For more information visit our web site: www.hubbell-ltg.com
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
Industrial Lighting
SFMM/SFM2
INTEGRAL BALLAST SUPPLY WIRE RATINGS
(SUFFIX “EA”)
SFMM/SFM2*
INTEGRAL BALLAST AMBIENT SUITABILITIES & T-RATINGS*
(SUFFIX “EA”)
WATTAGE/LAMP TYPE AMBIENT TEMPERATURE
40°C 55°C 65°C
175W MH 90°C 90°C 110°C
250W MH, PS 110°C 110°C —
400W MH, PS 110°C — —
150W HPS 90°C 90°C 110°C
250W HPS 90°C 110°C —
400W HPS 110°C — —
175W MV 90°C 110°C 110°C
250W MV 90°C 110°C —
400W MV 110°C — —
T-RATINGS & AMBIENT TEMPERATURE
WATTAGE & 40°C 55°C 65°C
LAMP TYPE CLASS I CLASS I CLASS I CLASS I CLASS1 CLASS I
DIV 2/ ZONE 2 DIV 2/ ZONE 2 DIV 2/ ZONE 2
ZONE 2 ExnR ZONE 2 ExnR ZONE 2 ExnR
AExnR AExnR AExnR
150W PS T1 T4 T1 T3 T1 T3
175W MH T1 T4 T1 T3 T1 T3
250W MH, PS T1 T3 T1 T1 — —
400W MH, PS T1 T3 — — — —
150W HPS T2A/T2 T4 T2 T4 T2 T3
250W HPS T1 T3 T1 T3 — —
400W HPS T1 T3 — — — —
175W MV T1 T4 T1 T4 T1 T3
250W MV T1 T3 T1 T3 — —
400W MV T1 T3 — — — —
* For standard SFM2 (less suffix EA), apply T-Ratings from 40°C column above.
