Taper Fill Surgical Technique Rev C
2015-04-28
: Pdf Taperfill Surgical Technique Rev C TaperFill_Surgical_Technique_Rev_C_ 4 2015 pdf
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
TaperFill™ Surgical Technique Table of Contents Indications and Contraindications TaperFill™ Hip Size Charts DJO Surgical 9800 Metric Boulevard Austin, TX (800) 456-8696 www.djosurgical.com 3 4-5 Preoperative Planning 6 General Architecture and Bone Quality 6 Planning for Equalization of Leg Lengths 6 Planning for Proper Offset 6 Prosthesis Size 6 Surgical Approach 7 Femoral Neck Resection 7 Use of the Box Osteotome 7 Canal Finder 8 Tapered Reamer 8 Broaching 9 Trial Reduction Final Implantation 10 11 Reduction 11 Closure 11 Aftercare 11 This brochure is presented to demonstrate a surgical technique. DJO Surgical, as the manufacturer of this device, does not practice medicine and cannot recommend this or any other surgical technique for use on a specific patient. The choice of the appropriate surgical technique is the responsibility of the surgeon performing the operation. 2▷ TaperFill™ Hip System Surgical Technique Surgical Technique Taperfill™ Hip System System Description The TaperFill Hip System consists of the following: • Increased sizing options with fourteen standard sizes: 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, and 19. • Standard and Lateralized offset versions in each size (Lateral offset only for size 19.) • Delta Ceramic heads are available. • Reduced neck geometry. • A twelve-degree proximal taper in the porous coating section. • Taper of the distal medial border of the prosthesis • Single reamer. • Broach handle attachment allowing for version control during broaching and simple removal of the broach. • Threaded stem inserts that allows for complete control of version during implantation. Indications Joint replacement is indicated for patients suffering from disability due to: • Noninflammatory degenerative joint disease including osteoarthritis and avascular necrosis of the natural femoral head • Rheumatoid arthritis • Correction of functional deformity • Femoral fracture This device may also be indicated in the salvage of previously failed surgical attempts. The constrained acetabular component is indicated for primary or revision patients at high risk of hip dislocation due to a history of prior dislocation, bone loss, soft tissue laxity, neuromuscular disease, or intra-operative instability and for who all other options to constrained acetabular components have been considered. This stem is to be press-fit. This stem is intended for cementless use. Contraindications Joint replacement is contraindicated where there is: • Infection or sepsis; • insufficient bone quality which may affect the stability of the implant; • muscular, neurological or vascular deficiencies, which compromise the affected extremity; • Osteomyelitis; • Rapid joint destruction or bone absorption apparent on roentgenogram; • Pathological conditions of the acetabulum, which would prevent achieving proper range of motion, appropriate head stability, and/or a well-seated and supported smooth articulation of the head within the acetabulum; • Alcoholism or other addictions; • Materials sensitivity; • Loss of ligamentous structures; • High levels of physical activity (e.g. competitive sports, heavy physical labor); • Materials sensitivity; • Pregnancy • Uncooperative patient or a patient with neuralgic disorders and incapable of following instructions • Distant foci of infections 3▷ TaperFill™ Hip System Surgical Technique TaperFill™ Hip Stem Sizing Charts The TaperFill Hip stem is press-fit titanium, P2® coated tri-tapered design. Each stem size is available in standard and lateralized offset versions (size 19 is only available in the lateral offset option). Standard PART # SIZE A NECK LENGTH B STEM LENGTH C NECK OFFSET D E DISTANCE TO A-A DISTANCE TO B-B F A-A M/L G A-A A/P H B-B M/L I B-B A/P 425-96-005 5 37 104.5 38 84 51 27 15 15 9 425-96-006 6 37 106 39 86 53 28 16 15 10 425-96-007 7 37 107.5 39 87 54 28 17 16 10 425-96-008 8 37 109 40 89 56 29 17 17 11 425-96-009 9 37 111 40 90 58 30 18 17 11 425-96-010 10 37 112.5 41 92 60 31 19 18 12 425-96-011 11 37 114 41 93 61 32 20 18 12 425-96-012 12 37 115.5 42 95 63 33 20 19 12 425-96-013 13 37 117 42 96 65 34 20 20 12 425-96-014 14 37 118.5 43 98 67 35 21 21 13 425-96-015 15 37 120 43 99 69 36 22 21 13 425-96-016 16 37 121.5 44 101 70 37 22 22 13 425-96-017 17 37 123 44 102 72 38 23 23 13 Lateralized PART # SIZE A NECK LENGTH 425-97-005 5 42.5 425-97-006 6 425-97-007 7 425-97-008 B STEM LENGTH C NECK OFFSET D E DISTANCE TO A-A DISTANCE TO B-B F 51 27 15 A-A M/L 104.5 46 84 42.5 106 47 86 53 28 42.5 107.5 47 87 54 28 8 42.5 109 48 89 56 425-97-009 9 42.5 111 48 90 425-97-010 10 42.5 112.5 49 425-97-011 11 42.5 114 49 425-97-012 12 42.5 115.5 50 95 425-97-013 13 42.5 117 50 96 425-97-014 14 42.5 118.5 51 98 67 425-97-015 15 42.5 120 51 99 69 425-97-016 16 42.5 121.5 52 101 70 425-97-017 17 42.5 123 52 102 425-97-019 19 42.5 125 53 105 4▷ TaperFill™ Hip System Surgical Technique G A-A A/P H B-B M/L I B-B A/P 15 9 16 15 10 17 16 10 29 17 17 11 58 30 18 17 11 92 60 31 19 18 12 93 61 32 20 18 12 63 33 20 19 12 65 34 20 20 12 35 21 21 13 36 22 21 13 37 22 22 13 72 38 23 23 13 74 39 24 25 13 A F C G E A SECTION A-A A B D B H B C I A SECTION B-B E A A B D B 5▷ TaperFill™ Hip System Surgical Technique B Preoperative Planning Proper preoperative planning is done both with and without the use of templates. Proper radiographs should generally include a single A/P of the pelvis and an A/P and lateral radiograph of the hip to include the proximal one-third of the femur. A radiograph with the hip in 15 degrees of internal rotation is preferred. If proper positioning of the hip is not possible, this must be taken into consideration when templating for prosthesis size, leg length, and offset. Whenever possible, x-ray magnification calibration should be used and radiographs representing 20% magnification should be a goal. The information obtained during the templating process is crucial to successful hip arthroplasty. Following the steps outlined below will greatly facilitate the ease of implantation and proper prosthesis choice and placement. It is important to note that templating is only a guide for prosthesis sizing and positioning. General Architecture and Bone Quality When assessing initial radiographs for general architecture and bone quality of the hip, pay special attention to: • Areas of bone loss, especially in the superior weight-bearing dome of the acetabulum. • Proximal femoral geometry, specifically the relationship between the size of the metaphyseal flare and the diameter of the femoral canal. • Cortical thickness both proximally and distally. • Degree of osteoporosis Planning for Equalization of Leg Lengths • Clinically measure the leg lengths and note any discrepancies. • Radiographically measure any leg length discrepancy on the A/P pelvis view using the relationship between a set point on the lesser trochanter and a line drawn along the inferior borders of both pubic rami. • Note the correlation with the clinical and radiographic measurements. 6▷ TaperFill™ Hip System Surgical Technique • Using the x-ray template for the neck-cutting guide, measure where a standard neck cut would be made. • Either the level of the neck cut can be adjusted or the templated implant size may be changed to adjust the discrepancy in leg length. Planning for Proper Offset The availability of two offsets allows not only for restoration of proper offsets in each individual patient, but also allows increased stability of the hip in each stem size without increasing leg length. • Draw a vertical line through the center of the femoral canal exiting proximally. • Locate the center of the femoral head and draw a horizontal line perpendicular to the vertical line from the center of the femoral head. • Measure the distance of the horizontal line. This is the offset. • Compare the offset to the offset table (page 4, column C). Once the size is templated, compare that determination to the recommended offset to estimate final prosthesis selection. Prosthesis Size • Using the template, align the centerline of the femoral stem to the center of the femoral shaft. • Use varying sizes to template. The proper size should be in contact with the endosteal surface laterally and medially in the porous coating section of the prosthesis. • Once a provisional size has been determined, overlay the standard and lateralized version of the same stem size and assess the relationship between the center of the femoral head on the template and the true anatomic femoral head. • Choose the prosthesis that overlays most accurately in size and offset. • As a check, once you determine your size by templating, compare the offset of that size with the offset, as previously measured in step three. Surgical Technique Surgical Approach Surgical approach is determined by surgeon preference. The TaperFill Hip stem and instrumentation have been designed to accommodate all surgical approaches with ease. General principles of proper arthroplasty surgical approach should be followed. These include: If the noted neck version is within this range with the leg in a neutral position, simply follow the version angle of the neck with the box osteotome and subsequent broaches. Adjust this accordingly. Figure 1 Figure 2 • Proper patient positioning. • An incision of adequate length. • Consistent use and placement of retractors for optimal visualization. Femoral Neck Resection The femoral neck cut can be made using the neck cutting guide by placing a pin in the center of the femoral head and sliding the guide over the pin (Figure 1). The distal part of the guide is centered over the femoral neck. Alternatively, you can place the femoral broach against the outer surface of the femur at the level determined by preoperative templating. You can then mark the osteotomy with an electrocautery. Prior to cutting, always check the level of the resection visually and in relation to the lesser trochanter for proper positioning. As a general rule, the femoral neck cut should be approximately 15mm above the lesser trochanter. After the femoral neck cut is made, the acetabular prosthesis is implanted. Use of the Box Osteotome Lateralization of the prosthesis is critical to proper positioning. Visualize the center of the femoral canal along the outer border and mark a vertical centerline using an electrocautery along the outer surface of the proximal femur extending proximally. Note where this line exits at your femoral neck cut. A rongeur is useful to initially remove laterally retained femoral neck. Centering the box osteotome over the vertical centerline, remove a few millimeters of proximal bone (Figure 2). Care must be taken to ensure proper version by placing the leg in a neutral rotation position and noting the version of the femoral neck. This allows a check for proper anteversion of the stem. Normal version is approximately 10-15 degrees of anteversion. 7▷ TaperFill™ Hip System Surgical Technique Instrumentation Guide [803-03-012] Box Osteotome [803-00-040] Canal Finder Figure 3 (a). Figure 3 (b). Figure 4 (a). Figure 4 (b). A thin, sharp canal finder is then used and placed down the centerline (Figure 3). This should encounter minimal resistance. Pay special attention to both medial/lateral and anterior/posterior placement of the canal finder. Tapered Reamer The tapered reamer should be attached to power, although hand reaming is possible. Placing the reamer down the center of the canal, ream straight down the canal to the distance determined by preoperative templating. The reamer has proximal markings corresponding to the prosthesis sizes. These marking should be brought down to the level of the osteotomy (Figure 4). Depth mark for corresponding implant size Instrumentation Starter Reamer [803-00-035] Tapered Reamer [803-03-001] 17 15 13 11 9 7 8▷ TaperFill™ Hip System Surgical Technique Insertion Depth Broaching Instrumentation The TaperFill System’s broach handle (Figure 5) is designed for quick attachment and release of the broaches. Insertion of the broach into the femoral cavity is accomplished by using a mallet against the proximal strike plate. Striking the underside of the strike plate facilitates removal of the broach. Broaching is begun with the smallest available broach. As a general guideline, follow the version previously determined by the box osteotome and pay special attention to varus/valgus and anterior/posterior positioning. Pay special attention to proper lateralization of each successive broach. While the prosthesis is designed for implantation straight down the canal, the surgeon can make modifications of the positioning as needed. Successive broaching is done until the prosthesis reaches a stable position and the level of the broach teeth approximates the neck resection (Figure 6). Calcar reaming may be performed; however, since this is a collarless prosthesis, it is not necessary (Figure 7). Excessive force is not necessary to seat the broach to a stable position. Figure 5 9▷ TaperFill™ Hip System Surgical Technique Figure 6 Small Calcar Reamer [803-00-032] Broach Handle [803-03-059] Large Calcar Reamer [803-00-033] Figure 7 Trial Reduction Figure 8 Once the broach reaches a position of stability, you are ready for trial reductions. The TaperFill Hip stem has two options, a standard and lateral offset (Figure 8). Neck trials are available in standard and lateralized versions (Figure 9). Either may be used on the same broach trial. Depending on your preoperative templating, place the appropriate head and neck trial on the broach (Figure 10). When performing trial reductions there are four important things to check: 1. Visually inspect the reduction of the head in the cup. Make sure the reduction is concentric and the appropriate amount of coverage of the femoral head is obtained. 2. Critical for the prevention of dislocation, assess appropriate tissue tension general, 1-2mm of pistoning is appropriate when pulling straight on the leg. Pulling the leg in a neutral position is important to get a true assessment of tissue tension. 3. Move the leg in a variety of positions to assess stability. The hip should be stable through a full functional range of motion. Pay special attention to particular maneuvers that lead to instability. Additionally assess the presence of anterior or posterior acetabular osteophytes that may cause the hip to sublux out of the cup. 4. Measure leg lengths at this time. If you are performing the surgery with the patient in a supine position, assessing proper leg lengths is straight forward. Patients in a lateral decubitus position present more difficulty. In those situations, your preoperative templating of the relationship of the center of the femoral head to the tip of the greater trochanter is that much more important. Depending upon your preoperative templating, you can assess your leg length status and adjust accordingly. Instrumentation Neck Trials [803-21-026/027] 10 ▷ Head Distractor Handle [803-03-036] TaperFill™ Hip System Surgical Technique Head Distractor Small [803-03-037] Head Distractor Large [803-03-038] Standard Lateral Standard Lateral Figure 9 Figure 10 Final Implantation Figure 12 (a). Figure 12 (b). Once the final construct is determined, final implantation of the prosthesis is performed. The TaperFill Hip stem is placed by hand into the prepared femur, and the stem inserter is then used to seat the implant. Seat the stem down the canal in the broached space (Figure 12). It is generally proud by one to three centimeters. Impact the prosthesis down to a stable position with a mallet. Visually confirm the prosthesis is stable on further impaction. An audible “tone change” occurs frequently when a stable position is reached. Take care not to impact the final prosthesis with too much force. Reduction Go through the same four steps outlined previously with trial head components. The proper final head is then placed and firmly impacted (Figure 13). The acetabulum is inspected for any bone or soft tissue and the hip is reduced. Closure Standard hip closure is then performed. Inspect the joint and the entire wound for bone and soft tissue and thoroughly irrigate. Attention to detail during the closure, with care to properly reapproximate key structures will improve joint stability and wound healing. Aftercare Postoperative instructions have some variability based on surgeon preference and patient factors. In general, patients are allowed full weight bearing with the TaperFill Hip stem, but are protected with a walker or Lofstrand crutches for six weeks mainly to protect the soft tissues. Physical therapy instructions are clear. The physical therapist is to only work on gait training and arthroplasty precautions. Patients are restricted from any passive range-of-motion or resistive exercises since these can stretch soft tissue repairs and capsular structures. Only active range-of-motion exercises through a limited range are recommended. The patients are walking on postoperative day one and discharged when specific parameters, set by the joint arthroplasty team, are met. 11 ▷ TaperFill™ Hip System Surgical Technique Figure 13 Instrumentation Stem Inserter [803-03-027] Head Impactor [803-03-018] CAUTION: Federal Law (USA) restricts this device to sale by or on the order of a physician. DJO Surgical I A DJO Global Company T 800.456.8696 D 512.832.9500 F 512.834.6300 9800 Metric Blvd. I Austin, TX 78758 I U.S.A. djosurgical.com ©2013 Encore Medical, L.P. See package insert for a complete listing of indications, contraindications, warnings, and precautions. 0020328-Rev C 06/14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2014:06:05 14:38:10-07:00 Creator : Adobe InDesign CS5.5 (7.5.3) Modify Date : 2015:04:23 09:08:48-05:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2015:04:23 09:08:48-05:00 Creator Tool : Adobe InDesign CS5.5 (7.5.3) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 8029 bytes, use -b option to extract), (Binary data 8121 bytes, use -b option to extract) Instance ID : uuid:4d50d3f0-d0a3-4043-939c-39e5efedd502 Document ID : xmp.did:F18A0C879A2168118083A85280D93E4C Original Document ID : xmp.did:2747D1FFDC2068118083FEB076C2F263 Rendition Class : proof:pdf History Action : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:2747D1FFDC2068118083FEB076C2F263, xmp.iid:2B47D1FFDC2068118083FEB076C2F263, xmp.iid:2C47D1FFDC2068118083FEB076C2F263, xmp.iid:B68FACDAA72168118083FEB076C2F263, xmp.iid:BB8FACDAA72168118083FEB076C2F263, xmp.iid:C08FACDAA72168118083FEB076C2F263, xmp.iid:1AA75209C02168118083FEB076C2F263, xmp.iid:1FA75209C02168118083FEB076C2F263, xmp.iid:1DA3C485C22168118083FEB076C2F263, xmp.iid:24A3C485C22168118083FEB076C2F263, xmp.iid:720746A6C42168118083FEB076C2F263, xmp.iid:DFF1775FC52168118083FEB076C2F263, xmp.iid:E0F1775FC52168118083FEB076C2F263, xmp.iid:1BC781C9C52168118083FEB076C2F263, xmp.iid:23C781C9C52168118083FEB076C2F263, xmp.iid:9B0324E3C82168118083FEB076C2F263, xmp.iid:99D1B0AACB2168118083FEB076C2F263, xmp.iid:5F9510CACC2168118083FEB076C2F263, xmp.iid:B9ED52FDCC2168118083FEB076C2F263, xmp.iid:B2FAEF53CF2168118083FEB076C2F263, xmp.iid:6C0B804FD02168118083FEB076C2F263, xmp.iid:D2252C29D12168118083FEB076C2F263, xmp.iid:EE94A7A1D12168118083FEB076C2F263, xmp.iid:4DC5FA7D872268118083FEB076C2F263, xmp.iid:FC096DA78E2268118083FEB076C2F263, xmp.iid:EA7D57E6072068118083F42639060FF2, xmp.iid:518A61E6072068118083F42639060FF2, xmp.iid:55CE22E30B2068118083F42639060FF2, xmp.iid:56CE22E30B2068118083F42639060FF2, xmp.iid:E65D2821CE2068118083F42639060FF2, xmp.iid:A010F8026E2168118083F42639060FF2, xmp.iid:ECF29F0F732168118083F42639060FF2, xmp.iid:F2F29F0F732168118083F42639060FF2, xmp.iid:630A5D47782168118083F42639060FF2, xmp.iid:690A5D47782168118083F42639060FF2, xmp.iid:C6A5ED92932168118083F42639060FF2, xmp.iid:8E41E8E8972168118083F42639060FF2, xmp.iid:0D6EB8C1982168118083F42639060FF2, xmp.iid:063FDBEB9D2168118083F42639060FF2, xmp.iid:EC9F8EFF9F2168118083F42639060FF2, xmp.iid:843CC522A12168118083F42639060FF2, xmp.iid:54879F67A12168118083F42639060FF2, xmp.iid:A27147A0B02168118083F42639060FF2, xmp.iid:BCB41F49312268118083F42639060FF2, xmp.iid:A964668A362268118083F42639060FF2, xmp.iid:F96E7B9F5D2268118083F42639060FF2, xmp.iid:E591FE555E2268118083F42639060FF2, xmp.iid:BE78CB9A5E2268118083F42639060FF2, xmp.iid:3CA215D65E2268118083F42639060FF2, xmp.iid:5F44F1CC602268118083F42639060FF2, xmp.iid:BE97E6FF602268118083F42639060FF2, xmp.iid:D1263224612268118083F42639060FF2, xmp.iid:26053DF4642268118083F42639060FF2, xmp.iid:E2EB8FB7C82B68118083B02A63E4BFDB, xmp.iid:D7734FC4C82B68118083B02A63E4BFDB, xmp.iid:4CE77665CA2B68118083B02A63E4BFDB, xmp.iid:4DE77665CA2B68118083B02A63E4BFDB, xmp.iid:E8A01742CE2B68118083B02A63E4BFDB, xmp.iid:FE26C5A6D12B68118083B02A63E4BFDB, xmp.iid:AFD3D6BDD52E68118083B02A63E4BFDB, xmp.iid:5EA0AB10D62E68118083B02A63E4BFDB, xmp.iid:CF5C7887D62E68118083B02A63E4BFDB, xmp.iid:B0B0353CD82E68118083B02A63E4BFDB, xmp.iid:56C65B81D82E68118083B02A63E4BFDB, xmp.iid:4A74CB77D92E68118083B02A63E4BFDB, xmp.iid:8B6F30A90E2068118083E0B968D4B27A, xmp.iid:C80783D9A820681180839176ABC9318C, xmp.iid:C40C5529A920681180839176ABC9318C, xmp.iid:C50C5529A920681180839176ABC9318C, xmp.iid:C60C5529A920681180839176ABC9318C, xmp.iid:C6A023C9AA20681180839176ABC9318C, xmp.iid:EE2ACA55AB20681180839176ABC9318C, xmp.iid:7B096AECAC20681180839176ABC9318C, xmp.iid:7C096AECAC20681180839176ABC9318C, xmp.iid:CE236A090D2068118083EA55C00FDC0E, xmp.iid:08159A5C0D2068118083EA55C00FDC0E, xmp.iid:362A437A0D2068118083EA55C00FDC0E, xmp.iid:01801174072068118083EDF924271601, xmp.iid:DB2D2974072068118083EDF924271601, xmp.iid:DC2D2974072068118083EDF924271601, xmp.iid:DD2D2974072068118083EDF924271601, xmp.iid:D6EC1D74072068118083CAE97AB3A0FA, xmp.iid:5ECF217407206811808386BBC5928BE6, xmp.iid:FD69D6368D226811822AE383C3BA5B64, xmp.iid:FE69D6368D226811822AE383C3BA5B64, xmp.iid:F4691F8D8D226811822AE383C3BA5B64, xmp.iid:F5691F8D8D226811822AE383C3BA5B64, xmp.iid:EE5881DF8F226811822AE383C3BA5B64, xmp.iid:C402890690226811822AE383C3BA5B64, xmp.iid:F0E185CE91226811822AE383C3BA5B64, xmp.iid:00B6FB2592226811822AE383C3BA5B64, xmp.iid:F4046ECF92226811822AE383C3BA5B64, xmp.iid:0043B83A93226811822AE383C3BA5B64, xmp.iid:8F45F73594226811822AE383C3BA5B64, xmp.iid:1E7C986994226811822AE383C3BA5B64, xmp.iid:1F7C986994226811822AE383C3BA5B64, xmp.iid:DD47EE7C072068118083950CC5EE51C6, xmp.iid:3E22F209082068118083950CC5EE51C6, xmp.iid:56CAF227092068118083AD35BFC6A775, xmp.iid:4A30FD27092068118083AD35BFC6A775, xmp.iid:0B6C8E910B2068118083AD35BFC6A775, xmp.iid:CCCB869C0D2068118083AD35BFC6A775, xmp.iid:7B5BBC630A2068118083A85280D93E4C, xmp.iid:7C5BBC630A2068118083A85280D93E4C, xmp.iid:7D5BBC630A2068118083A85280D93E4C, xmp.iid:7E5BBC630A2068118083A85280D93E4C, xmp.iid:7F5BBC630A2068118083A85280D93E4C, xmp.iid:805BBC630A2068118083A85280D93E4C, xmp.iid:19CABC479A2168118083A85280D93E4C, xmp.iid:66FC5A6F9A2168118083A85280D93E4C, xmp.iid:67FC5A6F9A2168118083A85280D93E4C, xmp.iid:68FC5A6F9A2168118083A85280D93E4C, xmp.iid:F18A0C879A2168118083A85280D93E4C History When : 2013:06:13 10:39:25-07:00, 2013:06:13 11:02:22-07:00, 2013:06:13 11:02:22-07:00, 2013:06:13 11:29:17-07:00, 2013:06:13 11:49:40-07:00, 2013:06:13 14:19:40-07:00, 2013:06:13 14:22:23-07:00, 2013:06:13 14:26:50-07:00, 2013:06:13 14:40:11-07:00, 2013:06:13 14:52:37-07:00, 2013:06:13 14:55:25-07:00, 2013:06:13 15:00:36-07:00, 2013:06:13 15:02:21-07:00, 2013:06:13 15:03:33-07:00, 2013:06:13 15:10:12-07:00, 2013:06:13 15:25:45-07:00, 2013:06:13 15:45:39-07:00, 2013:06:13 15:53:41-07:00, 2013:06:13 15:55:07-07:00, 2013:06:13 16:11:51-07:00, 2013:06:13 16:18:53-07:00, 2013:06:13 16:24:59-07:00, 2013:06:13 16:28:21-07:00, 2013:06:14 14:10:14-07:00, 2013:06:14 15:01:30-07:00, 2013:06:17 15:14:42-07:00, 2013:06:17 15:14:43-07:00, 2013:06:17 15:43:15-07:00, 2013:06:17 15:48:43-07:00, 2013:06:19 09:58:19-07:00, 2013:06:19 09:58:19-07:00, 2013:06:19 10:34:28-07:00, 2013:06:19 11:06:37-07:00, 2013:06:19 11:11:49-07:00, 2013:06:19 11:25:36-07:00, 2013:06:19 14:27:13-07:00, 2013:06:19 14:58:16-07:00, 2013:06:19 15:04:19-07:00, 2013:06:19 15:41:18-07:00, 2013:06:19 15:56:10-07:00, 2013:06:19 16:04:18-07:00, 2013:06:19 16:06:14-07:00, 2013:06:19 17:55:12-07:00, 2013:06:20 09:16:14-07:00, 2013:06:20 09:53:51-07:00, 2013:06:20 14:33:38-07:00, 2013:06:20 14:38:44-07:00, 2013:06:20 14:40:40-07:00, 2013:06:20 14:42:19-07:00, 2013:06:20 14:56:23-07:00, 2013:06:20 14:57:48-07:00, 2013:06:20 14:58:49-07:00, 2013:06:20 15:26:07-07:00, 2013:08:01 14:28:43-07:00, 2013:08:01 14:29:04-07:00, 2013:08:01 14:40:44-07:00, 2013:08:01 15:08:23-07:00, 2013:08:01 15:08:23-07:00, 2013:08:01 15:32:40-07:00, 2013:08:05 11:42:09-07:00, 2013:08:05 11:42:09-07:00, 2013:08:05 11:45:28-07:00, 2013:08:05 11:57:41-07:00, 2013:08:05 11:59:37-07:00, 2013:08:05 12:06:31-07:00, 2014:02:06 10:04:48-08:00, 2014:03:07 10:18:56-08:00, 2014:03:07 10:21:10-08:00, 2014:03:07 10:21:10-08:00, 2014:03:07 10:23:24-08:00, 2014:03:07 10:32:48-08:00, 2014:03:07 10:36:44-08:00, 2014:03:07 10:48:06-08:00, 2014:03:07 10:48:44-08:00, 2014:03:07 12:49:07-08:00, 2014:03:07 12:49:07-08:00, 2014:03:07 12:49:57-08:00, 2014:03:10 15:45:25-07:00, 2014:03:10 15:45:25-07:00, 2014:03:10 15:45:40-07:00, 2014:03:10 15:45:40-07:00, 2014:03:10 15:51:49-07:00, 2014:03:12 09:44:52-07:00, 2014:06:02 14:27:02-07:00, 2014:06:02 14:29:26-07:00, 2014:06:02 14:29:26-07:00, 2014:06:02 14:46:03-07:00, 2014:06:02 14:46:04-07:00, 2014:06:02 14:47:09-07:00, 2014:06:02 14:59:54-07:00, 2014:06:02 15:02:21-07:00, 2014:06:02 15:07:05-07:00, 2014:06:02 15:10:05-07:00, 2014:06:02 15:17:07-07:00, 2014:06:02 15:18:33-07:00, 2014:06:02 15:23:43-07:00, 2014:06:02 15:26:58-07:00, 2014:06:02 15:30:55-07:00, 2014:06:03 09:36:27-07:00, 2014:06:03 09:36:27-07:00, 2014:06:03 09:53:43-07:00, 2014:06:03 10:08:21-07:00, 2014:06:03 14:53:12-07:00, 2014:06:03 14:53:12-07:00, 2014:06:03 14:53:21-07:00, 2014:06:03 14:53:21-07:00, 2014:06:03 14:54:26-07:00, 2014:06:03 14:54:26-07:00, 2014:06:05 14:37:01-07:00, 2014:06:05 14:37:01-07:00, 2014:06:05 14:37:31-07:00, 2014:06:05 14:37:40-07:00, 2014:06:05 14:37:41-07:00 History Software Agent : Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5 History Changed : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /metadata, /, /metadata, /, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata Derived From Instance ID : xmp.iid:68FC5A6F9A2168118083A85280D93E4C Derived From Document ID : xmp.did:66FC5A6F9A2168118083A85280D93E4C Derived From Original Document ID: xmp.did:2747D1FFDC2068118083FEB076C2F263 Derived From Rendition Class : default Doc Change Count : 1167 Format : application/pdf Producer : Adobe PDF Library 9.9 Trapped : False Page Count : 12EXIF Metadata provided by EXIF.tools