Bt Fd101 Fast Rolling Door Of Control Receiver Function Operation Manual
User Manual: Pdf
Open the PDF directly: View PDF 
.
Page Count: 7
| Download | |
| Open PDF In Browser | View PDF |
BTFD101 Fast rolling door of control receiver function operation manual Ⅰ‧Receiver function 1. A transmitter can prevent copy function, the code have million sets. The receiver memorizes capacity of the 2000 transmitters. 2. Use transmitters to control receiver have two ways. One is 4keys to control receiver. The other is 1key（recycle mode）to control receiver. 3. Receiver builtin theft proof alarm function. Add a reed switch and alarm system. While rolling door is on top, press an OFFkey of transmitter, the receiver will into theft proof mode. If the rolling door is abnormal opened, will drive beeps. 4. Receiver provides 2 methods in lighter. One is added under DC24V 10W of lighter in receiver. Another is added a 24V relay to control existent lighter in garage. While rolling door is running, the lighter will brighten. 5. Protection function：the rolling door touch obstructer will up or stop while it is running. 6. Choose attached charge board and storage battery for charging in normal time. While power outage, the storage battery will supply power to work in rolling door. 7. Provide driving output in traffic signal. Add a relay that NC switch connect green light and NO switch connect red light. While the rolling door is opening or closing will show the traffic signal. 8. Set time (max to 127 seconds) to down function：the rolling door on top will count the time, after time is up, the rolling door will automatic down. Ⅱ‧Set time (max to 127 seconds)to down 1. Switch off SW31, SW32 and SW33 on the receiver. 2. After the rolling door on top, press OFF key of transmitter into power off mode. 3. Start set time to down – switch on SW32 in the receiver, then each beep 1 second, count beep for necessary downing time (max to 127 seconds). After counts necessary downing time, switch off SW32, receiver memory necessary downing time and stop beep. 4. Relieve downing time – switch on SW32 in the receiver, then each beep in 1 second. Less than 4 seconds switch off SW32, receiver clear the downing time and stop beep. Ⅲ‧Reset transmitter code and add transmitters i. Learn first transmitter code： 1. Lose power of the receiver over 15 seconds; prepare a transmitter. 2. Power on the receiver and press SW1 of receiver under 10 seconds, start beep that into learning code mode, synchronous press UP and DOWN key of transmitter under 10 seconds, after receiver got the signal will clean former code, memory this transmitter code, and stop beep and quit learning mode. ii. Add other transmitter code： 1. Prepare original transmitter and new transmitters. 2. Synchronous press STOP and OFF key of original transmitter, receive will beep that into add transmitter code mode. 3. Synchronous press UP and DOWN key of new transmitter under beeps 10 seconds, after receiver got the signal will memory new transmitter code. Add other Page 17 transmitters code will recount 10 seconds. If did not add transmitter code will beep and quit the learning code mode. Ⅳ‧Remote control receiver method by transmitter i. Remote control mode by 4 keys of transmitter： ( See illustration 4 in page 5) 1. Switch off SW33 in receiver board, 4 keys of transmitter can remote control receiver. 2. On 4 keys of transmitter mode, set SW31 and SW32 function as table： SW 31 SW 32 SW 33 OFF OFF ON OFF OFF ON FUNCTION Press OFF key of transmitter, receiver don’t accept manual switch control, and also don’t accept UP and DOWN of OFF transmitter. We called “power off mode” in this operation manual. Press OFF key of transmitter, receiver accept manual OFF switch and transmitter control. OFF Set necessary downing time: auto countdown. ii. 1 key of transmitter remote control mode (1 key recycle mode)： 1. Switch on SW33 on the receiver board, 1 key of transmitter in remote control mode; receiver was coerced set power off mode. 2. SW31 and SW32 were set which key of transmitter to control receiver as table： SW 31 SW 3 SW 33 FUNCTION 2 ON OFF ON UP key of transmitter to control receiver. (UP key recycle mode) OFF ON ON STOP key of transmitter to control receiver. (STOP key recycle mode) ON ON ON DOWN key of transmitter to control receiver. (DOWN key recycle mode) OFF OFF ON OFF key of transmitter to control receiver. (OFF key recycle mode) 3. In 1 key of transmitter mode, 4 keys of transmitter can control 4 receivers. 4. Remote control 2 receivers by 1 transmitter. One receiver adjust SW31 ON, SW32 OFF, SW33 OFF, can control receiver by UP and STOP and DOWN of transmitter. Another receiver adjust SW31 OFF, SW32 OFF, SW33 ON, can control receiver by OFF key of transmitter (recycle mode). iii. Notice item： 1. Code transportation method by wireless transmit, each receivers will receive signal while set code. When shared a transmitter in public and individual guard, attention order and methods in code learning. 2. Set remote controller in individual and public guard. Prior set code learning in individual guard, then add transmitter code in public guard. 3. The first transmitter keep well in public guard, forward add transmitters need the first transmitter into the code learning mode in the receiver. Ⅴ‧Alarm and reed switch of wiring and function i. Wiring： Page 27 1. Terminal M and V connect to reed switch, set reed switch in rolling door bottom. (See illustration 6 in page 6) 2. Provide NC/NO switch of alarm output to terminal CNT5 of the receiver board, ON and OFF of NC/NO switch to control beep in alarm. (See illustration 1 in page 4) ii. Function： 1. Theft proof mode: while rolling door is on bottom, receiver checks if have the signal of reed switch, if the receiver accepts signal will into the theft proof mode. When the rolling door was opened did not through manual switch or remote controller, receiver will drive alarm to beep until rid. 2. Rid beep: while beep in alarm, press any key of transmitter can rid beep. Ⅵ‧Type and wiring of accessory board i. Accessory board type： 1. Charge board – wire connect from UPS mark of the receiver board to charge board. Then wire connects from charge board to the storage battery. Receiver board charge power to the storage battery in common time. While lose power the storage battery provides power to receiver board. (See illustration 10 in page 7) 2. Traffic lights control board – connect wire from CNT4 on the receiver board to traffic lights control board that provide 2 pairs terminals, follow direction connect to green lamp and red lamp. Another two orange wires are input power on the traffic lights control board. 2 orange wires connect with adapter. Notice the receiver supply voltage is AC220V, traffic lights must use AC220V; if supply voltage is AC110V, and traffic lights must use AC110V. So traffic lights control board is according rolling door opening or closing to show traffic lights signal. While rolling door is opening will turn on the red lamp, while rolling door is closing will turn on the green lamp. (See illustration 2 in page 5) 3. Connect Interior lamp: provide terminal connect lamp. (See illustration 3 in page 5) Ⅶ‧Connect wiring of inferred signal i. Connect inferred signal： 1. Purpose: while rolling door is downing or stop, if the inferred sensor detected something, the rolling door will auto up. 2. Receiver board provides E and V of terminal to connect N.O. switch of inferred sensor. (See illustration 6 in page6) Page 37 Wires connection illustration 14 13 1 2 3 4 15 5 6 7 8 1 9 10 11 12 Alarm connection—Collocate with reed switch(See illustration 6). When rolling door closed at bottom, press OFF key of transmitter, receiver enter antithief mode. After into antithief mode, if rolling door didn’t open by manual switch or transmitter, receiver drove alarm to beeps. Input power ALARM 2 Connect traffic lights control board—Red lamp lights on when rolling door opens, green lamp lights on when rolling door down. Red light Green light Light power line Page 47 3 Connect interior lamp(DC24V/10W output ） —Receiver illumining light on when rolling door is running. Interior lamp 4 makes ð Function selected switch（SW3）—setting transmitter: 4keys control receiver or one key control receiver. ※Switch SW33 OFF: 4keys of transmitter to control. ※Switch SW33 ON: one key of transmitter to control. Forward to yourself put switch to down, represent :OFF Forward to yourself put switch to up, represent :ON 4keys control mode— Press OFF key of transmitter, receiver don’t accept manual switch control, and also don’t accept UP and DOWN of transmitter. Press OFF key of transmitter, receiver accept manual switch and transmitter control. Timing down automatically, setting time mode. One key recycle control mode— Receiver controlled by launcher’s “up” key. Receiver controlled by launcher’s “stop” key. Receiver controlled by launcher’s “down” key. Receiver controlled by launcher’s “off” key. 5 Obstruction selected switch（SW2 07 section）—when rolling door is running and touched obstruction, it can go up or stop. This selection switch can set the obstructed strength. More value indicates bigger obstruction. Page 57 6 Connection of 1key recycle control, infrared sensor, reed switch— C E M V Connect way1: 1 key recycle control C E M V Connect way2: infrared sensor C E M V Infrared receiver (N.O. switch) N.O. Infrared signal Connect way3: Reed switch Magnet C E M V 7 8 Induced (N.C. switch) ~ ~ ~ Reed switch Connect manual switch, control board of power instruction light (Set receiver’s cover in inside) — Connect manual switch in outside—If receiver at a far place, you can connect manual switch in outside. OUTSIDE SWITCH D S U V UP STOP D S U V 9 DOWN AC18V input end—AC18V output of transformer connect at this point. Page 67 10 UPS — UPS terminal connect to receiver board. UPS (Storage battery+ charge board) 11 AC24V input end—AC24V output of transformer connect at this point. 12 Connect MOTOR to receiver board. UP (Black) Common (Green) Down (White) 13 Connect counter (DC24V) to receiver board—After connected with DC24V counter, it count the number of times during rolling door is running. Count one time during motor is opening or closing. DC24V 888888 14 15 Beeper(used in setting mode selection, function setting, condition instruction)—know when will beep, please see receiver’s function operation manual. Switch of multiple magnify （ Current degree big – small, modify 4 ＞○ 3 ＞○ 2 ＞○ 1) — switch of multiple magnify ( ○ 1 ○ 3 ○ Bigger Medium 2 ○ Big（Manufactory set） 4 ○ Small EX1: Slat of roller door is more big or more heavy, load current will bigger, need modify switch of multiple magnify to next number (if switch on , turn to ) EX2: Slat of roller door is smaller or lighter, load current will smaller, need modify switch of multiple magnify to under number (if switch on , turn to ) Page 77
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 7 Creator : Macromedia FlashPaper 2.01.2283.0 Create Date : 2007:09:26 22:02:54+08:00 Producer : PDFlib 5.0.3 (C++/Win32)EXIF Metadata provided by EXIF.tools