G0513X2B G0513x2f M

G0513X2 g0513x2_m

G0513P g0513p_m

User Manual: Pdf G0513X2B

Open the PDF directly: View PDF .
Page Count: 108 [warning: Documents this large are best viewed by clicking the View PDF Link!]

INTRODUCTION
SECTION 1: SAFETY
- Safety Instructions for Machinery
- Additional Safety for Bandsaws
SECTION 2: POWER SUPPLY
- Availability
SECTION 3: SETUP
SECTION 4: OPERATIONS
SECTION 5: ACCESSORIES
- Basic Eye Protection
SECTION 6: MAINTENANCE
SECTION 7: SERVICE
SECTION 8: WIRING
SECTION 9: PARTS
WARRANTY & RETURNS

MODEL G0513 SERIES

HEAVY-DUTY 17" BANDSAW

OWNER'S MANUAL

(MODELS G0513, G0513P, G0513ANV,

& EXTREME MODELS G0513X2, G0513X2B,

G0513X2BF, & G0513X2F)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TS15097 PRINTED IN TAIWAN

Model

G0513X2B

For Model

G0513X2B

Only

Model

G0513ANV

This manual provides critical safety instructions on the proper setup,

operation, maintenance, and service of this machine/tool. Save this

document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual

may result in fire or serious personal injury—including amputation,

electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

This responsibility includes but is not limited to proper installation in

a safe environment, personnel training and usage authorization,

proper inspection and maintenance, manual availability and compre-

hension, application of safety devices, cutting/sanding/grinding tool

integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage

from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State

of California to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equip-

ment, such as those dust masks that are specially designed to filter

out microscopic particles.

Table of Contents

INTRODUCTION ............................................... 3

Manual Accuracy ........................................... 3

Contact Info.................................................... 3

G0513 Series Combination Manual ............... 3

Basic Controls ................................................ 4

Control Panel ............................................... 4

Front Controls .............................................. 4

Motor Brake ................................................. 4

Rear Controls .............................................. 5

SECTION 1: SAFETY ....................................... 8

Safety Instructions for Machinery .................. 8

Additional Safety for Bandsaws ................... 10

SECTION 2: POWER SUPPLY ...................... 11

Availability .................................................. 11

Full-Load Current Rating ........................... 11

Circuit Information ..................................... 11

Circuit Requirements ................................. 12

Grounding Requirements .......................... 12

Extension Cords ........................................ 14

Voltage Conversion ................................... 14

SECTION 3: SETUP ....................................... 15

Introduction .................................................. 15

Needed for Setup ......................................... 15

Unpacking .................................................... 15

Hardware Recognition Chart ....................... 16

Inventory ...................................................... 17

G0513, G0513P, & G0513ANV ................. 17

G0513X2 ................................................... 18

G0513X2F ................................................. 19

G0513X2B, G0513X2BF ........................... 20

Cleanup ........................................................ 21

Site Considerations ...................................... 21

Floor Load ................................................. 21

Placement Location ................................... 21

Moving & Placing Bandsaw ......................... 22

Using Eye Bolt ........................................... 22

Using Wood Blocks ................................... 22

Mounting ...................................................... 23

Bolting to Concrete Floors ......................... 23

Assembly ..................................................... 23

Installing Guide Post Handwheel, Positive

Stop Bolt, & Table ..................................... 23

Installing Fence

(G0513, G0513P, G0513ANV, G0513X2,

& G0513X2F) ............................................. 25

Installing Fence

(G0513X2B & G0513X2BF) ...................... 26

Installing Foot Brake Pedal

(G0513X2BF & G0513X2F) ...................... 27

Installing Resaw Fence

(G0513X2, G0513X2B, G0513X2BF, &

G0513X2F) .................................................. 27

Initial Blade Tracking ................................... 28

Adjusting Positive Stop ................................ 29

Dust Collection ............................................. 30

Power Cord Connection

(G0513X2BF & G0513X2F) ......................... 30

Test Run ...................................................... 31

Tensioning Blade ......................................... 33

Flutter Method ........................................... 33

Deflection Method ...................................... 34

Adjusting Blade Support Bearings ............... 35

Adjusting Blade Guides ............................... 36

Adjusting Blade Guides

(G0513, G0513P, & G0513ANV) .............. 37

Adjusting Blade Guide Bearings

(G0513X2, G0513X2B, G0513X2BF, &

G0513X2F) ................................................ 38

Aligning Table .............................................. 39

Aligning Fence ............................................. 40

Aligning Fence

(G0513, G0513P, G0513ANV, G0513X2,

& G0513X2F) ............................................. 40

Aligning Fence

(G0513X2B & G0513X2BF) ...................... 41

Calibrating Miter Gauge ............................... 41

SECTION 4: OPERATIONS ........................... 42

Disabling & Locking Switch

(G0513, G0513P, G0513ANV, G0513X2) ... 42

Disabling & Locking Switch

(G0513X2B, G0513X2BF, G0513X2F) ........ 43

General Overview ........................................ 43

Straight Cuts .............................................. 43

Irregular Cuts ............................................. 43

Basic Cutting Tips ..................................... 43

Operation Overview ..................................... 44

Workpiece Inspection................................... 44

Table Tilt ...................................................... 45

Models G0513, G0513P, & G0513ANV .... 45

Models G0513X2, G0513X2B,

G0513X2BF, & G0513X2F ........................ 45

Guide Post ................................................... 46

Fine Tune Tracking ...................................... 46

Blade Selection ............................................ 47

Blade Terminology ..................................... 47

Blade Length ............................................. 47

Blade Width ............................................... 47

Blade Material ............................................ 47

Tooth Set ................................................... 48

Tooth Type ................................................ 48

Blade Selection Chart .................................. 49

Blade Breakage ........................................... 50

Blade Care & Break-In ................................. 50

Blade Changes ............................................ 51

Removing Blade ........................................ 51

Installing Blade .......................................... 51

Blade Speed ................................................ 52

Crosscutting ................................................. 53

Resawing ..................................................... 53

Cutting Curves ............................................. 54

Stacked Cuts................................................ 55

SECTION 5: ACCESSORIES ......................... 56

Basic Eye Protection ................................. 57

SECTION 6: MAINTENANCE ......................... 58

Schedule ...................................................... 58

Wheel Brush ................................................ 58

Cleaning & Protecting .................................. 58

Lubrication ................................................... 58

Blade Post Rack ........................................ 58

Tension Adjustment Assembly .................. 59

Trunnions ................................................... 59

SECTION 7: SERVICE ................................... 60

Troubleshooting ........................................... 60

V-Belt Service .............................................. 63

Checking V-Belt ......................................... 63

Replacing V-Belt ........................................ 63

Blade Lead ................................................... 64

Adjusting Wheel Brush ................................ 65

Adjusting Tension Lever .............................. 65

Adjusting Guide Post Travel ........................ 66

Checking/Adjusting Guide Post Parallel

with Blade Side-to-Side ............................. 66

Checking/Adjusting Guide Post Parallel

with Blade Front-to-Back ........................... 67

Aligning Wheels ........................................... 68

Checking Coplanarity ................................ 68

Shimming Upper Wheel ............................ 69

Adjusting Lower Wheel .............................. 70

Magnetic Brake Adjustment

(G0513X2B, G0513X2BF) ........................... 70

SECTION 8: WIRING ...................................... 71

Wiring Safety Instructions ............................ 71

G0513, G0513P, G0513ANV, & G0513X2

Wiring Diagram ............................................ 72

G0513X2B Wiring Diagram ......................... 73

G0513X2BF Wiring Diagram ....................... 74

G0513X2F 220V Wiring Diagram ................ 75

G0513X2F 110V Wiring Diagram ................ 76

SECTION 9: PARTS ....................................... 77

G0513/G0513P/G0513ANV Main ................ 77

G0513/G0513P/G0513ANV

Table, Trunnion, & Lower Blade Guides...... 79

G0513/G0513P/G0513ANV Fence .............. 80

G0513/G0513P/G0513ANV

Upper Blade Guides & Miter Gauge ............ 81

G0513 Labels............................................... 83

G0513P Labels ............................................ 84

G0513ANV Labels ....................................... 85

G0513X2 Main ............................................. 86

G0513X2 Labels .......................................... 88

G0513X2B Main........................................... 89

G0513X2B Labels ........................................ 91

G0513X2BF Main ........................................ 92

G0513X2BF Labels...................................... 94

G0513X2F Main ........................................... 95

G0513X2F Labels ........................................ 97

G0513X2, G0513X2B, G0513X2BF, &

G0513X2F

Guides & Trunnions ..................................... 98

G0513X2 & G0513X2F

Fence Assembly & Table ........................... 100

G0513X2B & G0513X2BF

Fence Assembly & Table ........................... 101

G0513X2BF & G0513X2F Foot Brake ...... 102

WARRANTY & RETURNS ........................... 105

G0513 Series Bandsaws -3-

INTRODUCTION

We are proud to provide a high-quality owner’s

manual with your new machine!

made every effort to be exact with the

instruc-

tions, specifications, drawings, and photographs

in this manual. Sometimes we make mistakes, but

our policy of continuous improvement also means

that

sometimes the machine

you receive is

slightly different than shown in the manual

If you find this to be the case, and the difference

between the manual and machine leaves you

confused or unsure about something

check our

website for an updated version. W

e post

current

manuals and

manual updates for free

on our web-

site at

www.grizzly.com.

Alternatively, you can call our Technical Support

for help. Before calling, make sure you write down

the

Manufacture Date and Serial Number

from

the machine ID label (see below). This information

is required for us to provide proper tech support,

and it helps us determine if updated documenta-

tion is available for your machine.

Manufacture Date

Serial Number

Manual Accuracy

We stand behind our machines! If you have ques-

tions or need help, contact us with the information

below. Before contacting, make sure you get the

serial number

and manufacture date

from the

machine ID label. This will help us help you faster.

Grizzly Technical Support

1815 W. Battlefield

Springfield, MO 65807

Phone: (570) 546-9663

Email: techsupport@grizzly.com

We want your feedback on this manual. What did

you like about it? Where could it be improved?

Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: manuals@grizzly.com

Contact Info

G0513 Series

Combination Manual

The G0513 Series Bandsaws share many similari-

ties. Thus, this combination manual includes infor-

mation for all seven models of the G0513 Series

Bandsaws.

Unless otherwise specified, information applies to

all models. Headers are used to identify informa-

tion that only applies to specific models.

-4- G0513 Series Bandsaws

Basic Controls

Refer to Figures 1–4 and the following descrip-

tions to become familiar with the basic controls

and components of your bandsaw. Knowledge of

these controls and terminology will help you better

understand this manual.

Control Panel

The 2-button power switch on Models G0513,

G0513P, and G0513X2 is located on the column

for easy access (see Figure 1). The power button

can be disabled with a padlock to prevent unau-

thorized startup of the bandsaw (refer to Page 42

for additional details).

Figure 1. 2-Button power switch.

Figure 2. Control panel with a switch disabling

lock.

Power Switch

Key

On Button

Off Button

The Models G0513X2B, G0513X2BF, and

G0513X2F feature a power switch that can be

disabled with a key to prevent unauthorized start-

ing of the machine (see Figure 2). To disable

the switch, turn the key to "0" and remove it. To

enable the switch, insert the key and turn it to "1."

Front Controls

A. Blade Tension Scale: Allows for easy moni-

toring of blade tension in arbitrary numbers

1–8.

B. Blade Tension Handwheel: Tensions blade

in gradual increments.

C. Blade Tracking Window: Allows you to

monitor blade tracking on the wheel without

opening the wheel cover.

D. Fence and Miter Gauge: Supports workpiece

for controlled straight or angled cuts.

Figure 3. Front controls

(G0513X2BF shown).

E. Foot Brake (Models G0513X2BF &

G0513X2F): Quickly stops bandsaw blade

and motor.

Motor Brake

The Models G0513X2B and G0513X2BF have a

motor brake that activates and quickly stops the

blade when the OFF button is used, or the foot

pedal is pressed on the Model G0513X2BF.

G0513 Series Bandsaws -5-

Rear Controls

F. Wheel Cover Lock Knobs: Secure the

wheel covers.

G. Quick-Release Blade Tension Lever:

Adjusts blade tension for quick blade chang-

es.

H. Blade Tracking Knob and Lock Lever:

Moves and locks upper wheel tilt for blade

tracking.

I. Table Tilt Controls: Adjusts table tilt and

locks the table in place.

J. Magnetic Switch: Provides thermal overload

protection for the motor.

K. Lower Wheel Adjustment Hub: Used when

adjusting coplanarity of the wheels.

L. Guide Post Handwheel and Lock Knob:

Quickly moves the upper guide post to the

desired height; locks setting.

Figure 4. Rear controls

(G0513X2B shown).

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

-6- G0513 Series Bandsaws

MODEL G0513 SERIES 17" BANDSAWS

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

Model Number G0513/G0513P/

G0513ANV G0513X2 G0513X2B G0513X2BF G0513X2F

Product Dimensions

Weight 266 lbs. 325 lbs. 352 lbs. 357 lbs. 335 lbs.

Width (side-to-side) x Depth

(front-to-back) x Height 32" x 32" x 73"

Footprint (Length x Width) 27" x 17

3⁄4"

Shipping Dimensions

Type Wood Slat Crate

Weight 342 lbs. 418 lbs. 446 lbs. 460 lbs. 434 lbs.

Length x Width x Height 20" x 30" x 81" 31" x 21" x 81" 31" x 20" x 81" 31" x 21" x 81"

Electrical

Power Requirement 110V/220V, Single-Phase, 60 Hz 220V, Single-Phase, 60 Hz

110V/220V,

Single-Phase,

60 Hz

Full Load Current 20A at 110V,

10A at 220V

19A at 110V,

9.5A at 220V 8.7A 10A 20A at 110V, 10A

at 220V

Minimum Circuit Size 30A at 110V, 15A at 220V 15A 30A at 110V, 15A

at 220V

Prewired 220V

Switch 2-Button Power Switch Magnetic w/Thermal Overload Protection

Switch Voltage 110V/220V 220V 110V/220V

Cord Included Yes No

Plug Included No Yes, NEMA 6-15 No

Motor

Type TEFC Capacitor Start Induction

Horsepower 2 HP

Voltage 110V/220V 220V 110V/220V

Phase Single-Phase

Amperage 20A at 110V,

10A at 220V

19A at 110V,

9.5A at 220V 8.7A 10A 20A at 110V, 10A

at 220V

Speed 1725 RPM

Cycle 60 Hz

Power Transfer Belt Drive

Bearings Shielded and Permanently Lubricated

Operation

Blade Speeds 1700, 3500 FPM

Table Tilt Left 10°, Right

45° Left 5°, Right 45°

G0513 Series Bandsaws -7-

Model Number G0513/G0513P/

G0513ANV G0513X2 G0513X2B G0513X2BF G0513X2F

Cutting Capacities

Maximum Cutting Height 12

1⁄8"1 2 "

Maximum Capacity Left of

Blade 16

1⁄4"

Blade Information

Standard Blade Length 131

1⁄2"

Blade Width Range 1⁄8"–1"

Blade Guides Roller Disc, Ball

Bearings Ball Bearings

Guide Post Size 1.18" (30mm) Square

Guide Post Type Square Tubing, 0.075" in Wall Thickness

Table Dimensions

Length x Width x Thickness 17" x 17" x 1

1⁄2" 23

5⁄8" x 17

1⁄4" x 1

1⁄2"

Floor to Table Height 37

1⁄2"

Fence Information

Locks in Front Yes

Locks in Rear No

Adjustable for Blade Lead Yes

Resaw Fence Included No Yes

Construction

Table Precision-Ground Cast Iron

Fence Deluxe Extruded

Aluminum Cast Iron Fence w/ Extruded Aluminum Resaw Fence

Body Reinforced Steel

Wheels

Computer-

Balanced Cast

Aluminum

Computer-Balanced Cast Iron

Wheel Tire Polyurethane

Wheel Covers Pre-Formed Steel

Paint Powder Coated

Other Related Information

Foot Brake No Yes

Motor Brake No Yes No

Wheel Diameter 16

3⁄4"

Wheel Width 1

1⁄4"

Dust Ports 2 at 4"

Mobile Base Model D2057A

Other Specifications

Country of Origin Taiwan

Warranty 1 Year

ISO Factory Yes

Serial Number Location ID Label on Upper Wheel Cover

Assembly Time 1 Hour

-8- G0513 Series Bandsaws

ELECTRICAL EQUIPMENT INJURY RISKS. You

can be shocked, burned, or killed by touching live

electrical components or improperly grounded

machinery. To reduce this risk, only allow qualified

service personnel to do electrical installation or

repair work, and always disconnect power before

accessing or exposing electrical equipment.

DISCONNECT POWER FIRST.

Always discon-

nect machine from power supply BEFORE making

adjustments, changing tooling, or servicing machine.

This prevents an injury risk from unintended startup

or contact with live electrical components.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating or

observing machinery to reduce the risk of eye

injury or blindness from flying particles. Everyday

eyeglasses are NOT approved safety glasses.

OWNER’S MANUAL. Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained oper-

ators have a higher risk of being hurt or killed.

Only allow trained/supervised people to use this

machine. When machine is not being used, dis-

connect power, remove switch keys, or lock-out

machine to prevent unauthorized use—especially

around children. Make your workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use

machinery in areas that are wet, cluttered, or have

poor lighting. Operating machinery in these areas

greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental

alertness is required for safe operation of machin-

ery. Never operate under the influence of drugs or

alcohol, when tired, or when distracted.

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words intended to convey the level of impor-

tance of the safety messages. The progression of symbols is described below. Remember that

safety messages by themselves do not eliminate danger and are not a substitute for proper

accident prevention measures. Always use common sense and good judgment.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

This symbol is used to alert the user to useful information about

proper operation of the machine.

NOTICE

SECTION 1: SAFETY

Safety Instructions for Machinery

G0513 Series Bandsaws -9-

WEARING PROPER APPAREL. Do not wear

clothing, apparel or jewelry that can become

entangled in moving parts. Always tie back or

cover long hair. Wear non-slip footwear to reduce

risk of slipping and losing control or accidentally

contacting cutting tool or moving parts.

HAZARDOUS DUST. Dust created by machinery

operations may cause cancer, birth defects, or

long-term respiratory damage. Be aware of dust

hazards associated with each workpiece mate-

rial. Always wear a NIOSH-approved respirator to

reduce your risk.

HEARING PROTECTION. Always wear hear-

ing protection when operating or observing loud

machinery. Extended exposure to this noise

without hearing protection can cause permanent

hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on

machinery can become dangerous projectiles

upon startup. Never leave chuck keys, wrenches,

or any other tools on machine. Always verify

removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use

this tool for its intended purpose—do not force

it or an attachment to do a job for which it was

not designed. Never make unapproved modifica-

tions—modifying tool or using it differently than

intended may result in malfunction or mechanical

failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing

and balance at all times when operating machine.

Do not overreach! Avoid awkward hand positions

that make workpiece control difficult or increase

the risk of accidental injury.

CHILDREN & BYSTANDERS. Keep children and

bystanders at a safe distance from the work area.

Stop using machine if they become a distraction.

GUARDS & COVERS. Guards and covers reduce

accidental contact with moving parts or flying

debris. Make sure they are properly installed,

undamaged, and working correctly BEFORE

operating machine.

FORCING MACHINERY. Do not force machine.

It will do the job safer and better at the rate for

which it was designed.

NEVER STAND ON MACHINE. Serious injury

may occur if machine is tipped or if the cutting

tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement dur-

ing operation greatly increases risk of injury or

loss of control. Before starting, verify machine is

stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

this owner’s manual or the manufacturer for rec-

ommended accessories. Using improper acces-

sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the

risk of accidental injury, turn machine OFF and

ensure all moving parts completely stop before

walking away. Never leave machine running

while unattended.

MAINTAIN WITH CARE. Follow all maintenance

instructions and lubrication schedules to keep

machine in good working condition. A machine

that is improperly maintained could malfunction,

leading to serious personal injury or death.

DAMAGED PARTS. Regularly inspect machine

for damaged, loose, or mis-adjusted parts—or

any condition that could affect safe operation.

Immediately repair/replace BEFORE operating

machine. For your own safety, DO NOT operate

machine with damaged parts!

MAINTAIN POWER CORDS. When disconnect-

ing cord-connected machines from power, grab

and pull the plug—NOT the cord. Pulling the cord

may damage the wires inside. Do not handle

cord/plug with wet hands. Avoid cord damage by

keeping it away from heated surfaces, high traffic

areas, harsh chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time

you experience difficulties performing the intend-

ed operation, stop using the machine! Contact our

Technical Support at (570) 546-9663.

-10- G0513 Series Bandsaws

Additional Safety for Bandsaws

Serious cuts, amputation, or death can occur from contact with the moving saw blade during

operation or if blade breakage occurs. To reduce this risk, anyone operating this machine

MUST completely heed the hazards and warnings below.

GUARDS/COVERS. Blade guards and covers

protect operator from the moving bandsaw blade.

The wheel covers protect operator from getting

entangled with rotating wheels or other moving

par t s. O N LY operate this bandsaw with blade

guard in proper position and wheel covers com-

pletely closed.

BLADE REPLACEMENT. To avoid mishaps that

could result in operator injury, make sure blade

teeth face down toward table and blade is prop-

erly tensioned and tracked before operating.

UPPER BLADE GUIDE SUPPORT. To reduce

exposure of operator to blade and provide maxi-

mum blade support while cutting, keep upper

blade guides adjusted to just clear workpiece.

CUTTING TECHNIQUES. To avoid blade getting

pulled off wheels or accidentally breaking and

striking operator, always turn bandsaw OFF and

wait for blade to come to a complete stop before

backing workpiece out of blade. DO NOT back

workpiece away from blade while bandsaw is run-

ning. DO NOT force or twist blade while cutting,

especially when sawing small curves. This could

result in blade damage or breakage.

WORKPIECE SUPPORT. To maintain maximum

control and reduce risk of blade contact/break-

age, always ensure adequate support of long/

large workpieces. Always keep workpiece flat and

firm against table/fence when cutting to avoid loss

of control. If necessary, use a jig or other work-

holding device.

WORKPIECE MATERIAL. This machine is

intended for cutting natural and man-made wood

products, and laminate covered wood products.

This machine is NOT designed to cut metal,

glass, stone, tile, etc.

HAND PLACEMENT. Placing hands or fingers

in line with blade during operation may result in

serious injury if hands slip or workpiece moves

unexpectedly. Do not position fingers or hands in

line with blade, and never reach under table while

blade is moving.

SMALL/NARROW WORKPIECES. If hands slip

during a cut while holding small workpieces

with fingers, serious personal injury could occur.

Always support/feed small or narrow workpieces

with push sticks, push blocks, jig, vise, or some

type of clamping fixture.

BLADE SPEED. Cutting workpiece before blade

is at full speed could cause blade to grab work-

piece and pull hands into blade. Allow blade to

reach full speed before starting cut. DO NOT start

machine with workpiece contacting blade.

FEED RATE. To avoid risk of workpiece slipping

and causing operator injury, always feed stock

evenly and smoothly.

BLADE CONDITION. Dull blades require more

effort to perform cut, increasing risk of accidents.

Do not operate with dirty, dull, cracked or badly

worn blades. Inspect blades for cracks and miss-

ing teeth before each use. Always maintain proper

blade tension and tracking while operating.

CLEARING JAMS AND CUTOFFS. Always stop

bandsaw and disconnect power before clearing

scrap pieces that get stuck between blade and

table insert. Use brush or push stick, not hands,

to clean chips/cutoff scraps from table.

BLADE CONTROL. To avoid risk of injury due to

blade contact, always allow blade to stop on its

own. DO NOT try to stop or slow blade with your

hand or the workpiece.

G0513 Series Bandsaws -11-

SECTION 2: POWER SUPPLY

Availability

Before installing the machine, consider the avail-

ability and proximity of the required power supply

circuit. If an existing circuit does not meet the

requirements for this machine, a new circuit must

be installed. To minimize the risk of electrocution,

fire, or equipment damage, installation work and

electrical wiring must be done by an electrician or

qualified service personnel in accordance with all

applicable codes and standards.

Full-Load Current Rating

The full-load current rating is the amperage a

machine draws at 100% of the rated output power.

On machines with multiple motors, this is the

amperage drawn by the largest motor or sum of all

motors and electrical devices that might operate

at one time during normal operations.

G0513, G0513P, G0513ANV, & G0513X2F

Full-Load Current Rating

At 110V ..................................................20 Amps

At 220V .................................................10 Amps

G0513X2 Full-Load Current Rating

At 110V .................................................. 19 Amps

At 220V ................................................9.5 Amps

G0513X2B Full-Load Current Rating

At 220V ........................................................ 8.7A

G0513X2BF Full-Load Current Rating

At 220V ......................................................... 10A

The full-load current is not the maximum amount

of amps that the machine will draw. If the machine

is overloaded, it will draw additional amps beyond

the full-load rating.

If the machine is overloaded for a sufficient length

of time, damage, overheating, or fire may result—

especially if connected to an undersized circuit.

To reduce the risk of these hazards, avoid over-

loading the machine during operation and make

sure it is connected to a power supply circuit that

meets the specified circuit requirements.

Note: Circuit requirements in this manual apply to

a dedicated circuit—where only one machine will

be running on the circuit at a time. If machine will

be connected to a shared circuit where multiple

machines may be running at the same time, con-

sult an electrician or qualified service personnel to

ensure circuit is properly sized for safe operation.

A power supply circuit includes all electrical

equipment between the breaker box or fuse panel

in the building and the machine. The power sup-

ply circuit used for this machine must be sized to

safely handle the full-load current drawn from the

machine for an extended period of time. (If this

machine is connected to a circuit protected by

fuses, use a time delay fuse marked D.)

Circuit Information

Electrocution, fire, shock,

or equipment damage

may occur if machine is

not properly grounded

and connected to power

supply.

-12- G0513 Series Bandsaws

Figure 5. Typical 6-15 plug and receptacle.

Grounding Prong

Current Carrying Prongs

6-15 PLUG

GROUNDED

6-15 RECEPTACLE

Grounding Requirements

This machine MUST be grounded. In the event

of certain malfunctions or breakdowns, grounding

reduces the risk of electric shock by providing a

path of least resistance for electric current.

Grounding Requirements for 220V: The plug

specified under “Circuit Requirements for 220V

Operation” on this page has a grounding prong

that must be attached to the equipment-grounding

wire inside the specified power cord. The plug

must only be inserted into a matching recep-

tacle (see Figure 5) that is properly installed and

grounded in accordance with all local codes and

ordinances.

Model Number G0513, G0513P, G0513ANV, G0513X2,

G0513X2F G0513X2B & G0513X2BF

Circuit Requirements For 220V Operation:

Nominal Voltage 220V/240V

Cycle 60 Hz

Phase Single-Phase

Power Supply Circuit 15 Amps

Plug/Receptacle NEMA 6-15

Power Cord “S”-Type, 3-Wire, 14 AWG, 300 VAC

Circuit Requirements For 110V Operation:

Nominal Voltage 110V/120V

N/A

Cycle 60 Hz

Phase Single-Phase

Power Supply Circuit 30 Amps

Plug/Receptacle NEMA L5-30

Power Cord “S”-Type, 3-Wire, 12 AWG, 300 VAC

Circuit Requirements

These machines are prewired to operate on a 220V power supply circuit that has a verified ground and meet

the 220V operation requirements listed below.

Models G0513, G0513P, G0513ANV, G0513X2, and G0513X2F can be converted to operate on a 110V

power supply (refer to Voltage Conversion instructions beginning on Page 14) that has a verified ground

and meet the 220V operation requirements listed below.

G0513 Series Bandsaws -13-

No adapter should be used with plug. If

plug does not fit available receptacle, or if

machine must be reconnected for use on a

different type of circuit, reconnection must

be performed by an electrician or qualified

service personnel, and it must comply with

all local codes and ordinances.

Grounding Requirements for 110V: The plug

specified under “Circuit Requirements for 110V

Operation” on the previous page has a grounding

prong that must be attached to the equipment-

grounding wire inside the specified power cord.

The plug must only be inserted into a matching

receptacle (see Figure 6) that is properly installed

and grounded in accordance with all local codes

and ordinances.

Figure 6. Typical L5-30 plug and receptacle.

Grounding Prong

is Hooked

Hot

Neutral

L5-30 GROUNDED

LOCKING

RECEPTACLE

L5-30

LOCKING

PLUG

For your own safety and protection of

property, consult an electrician if you are

unsure about wiring practices or electrical

codes in your area.

Improper connection of the equipment-grounding

wire can result in a risk of electric shock. The

wire with green insulation (with or without yellow

stripes) is the equipment-grounding wire. If repair

or replacement of the power cord or plug is nec-

essary, do not connect the equipment-grounding

wire to a live (current carrying) terminal.

Check with a qualified electrician or service per-

sonnel if you do not understand these grounding

requirements, or if you are in doubt about whether

the tool is properly grounded. If you ever notice

that a cord or plug is damaged or worn, discon-

nect it from power, and immediately replace it with

a new one.

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

-14- G0513 Series Bandsaws

Extension Cords

We do not recommend using an extension cord

with this machine.

If you must use an extension

cord, only use it if absolutely necessary and only

on a temporary basis.

Extension cords cause voltage drop, which can

damage electrical components and shorten motor

life. Voltage drop increases as the extension cord

size gets longer and the gauge size gets smaller

(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must

be in good condition and contain a ground wire

and matching plug/receptacle. Additionally, it must

meet the following size requirements:

Minimum Gauge Size at 220V .............14 AWG

Minimum Gauge Size at 110V ..............12 AWG

Maximum Length (Shorter is Better).......50 ft.

Voltage Conversion

The voltage conversion MUST be performed by

an electrician or a qualified service personnel.

Models G0513, G0513P, G0513ANV, &

G0513X2

To perform the voltage conversion, install the

correct plug and rewire the motor to the new volt-

age, according to the wiring diagram provided on

Page 73.

Model G0513X2F

To perform the voltage conversion, replace the

magnetic switch with the 110V version (Part No.

P0513X2F244), install the correct power cord

and plug, and rewire the motor to the new volt-

age, according to the wiring diagram provided on

Page 76.

If the diagram included on the motor con-

flicts with the one in this manual, the motor

may have changed since the manual was

printed. Use the diagram provided on the

motor.

G0513 Series Bandsaws -15-

SECTION 3: SETUP

This machine was carefully packaged for safe

transport. When unpacking, separate all enclosed

items from packaging materials and inspect them

for shipping damage.

If items are damaged

please

call us immediately at (570) 546-9663.

IMPORTANT:

Save all packaging materials until

you are completely satisfied with the machine and

have resolved any issues between Grizzly or the

shipping agent. You MUST have the original pack-

aging to file a freight claim. It is also extremely

helpful if you need to return your machine later.

Unpacking

Description Qty

• Additional People ....................................... 1

• Safety Glasses .........................1 per Person

• Cleaner/Degreaser ..................... As Needed

• Disposable Shop Rags ............... As Needed

• Forklift/Strap or Chain w/Lifting Hook

(Each component rated for at least 1000 lbs)

..........................................................1 Each

• 1x4 & 2x4 Shims (Optional) ............... 1 Each

• Feeler Gauges 0.004", 0.016" ............ 1 Each

• Straightedge ............................................... 1

• Fine Ruler ................................................... 1

• Machinist's Square ..................................... 1

• Phillips Screwdriver #2 ............................... 1

• Hex Wrench 6mm ....................................... 1

• Dust Collection System .............................. 1

• Dust Hose 4" .............................................. 2

• Hose Clamps 4" ......................................... 2

Introduction

The bandsaw is an efficient and flexible wood-

working machine. However, the bandsaw func-

tions are inter-dependent and each one must be

properly set up and adjusted so that the entire

machine operates correctly.

For instance, in this SETUP section, you will do

an initial blade tensioning before adjusting the

blade tracking. This will also allow you to properly

adjust the table angle, positive stop, blade guides,

and support bearing.

To prepare the machine for safe cutting and good

results, take extra care when performing these

inter-dependent tasks and complete them in the

correct order.

This machine presents

serious injury hazards

to untrained users. Read

through this entire manu-

al to become familiar with

the controls and opera-

tions before starting the

machine!

Needed for Setup

The following items are needed, but not included,

for the setup/assembly of this machine.

HEAVY LIFT!

Straining or crushing injury

may occur from improperly

lifting machine or some of

its parts. To reduce this risk,

get help from other people

and use a forklift (or other

lifting equipment) rated for

weight of this machine.

-16- G0513 Series Bandsaws

Hardware Recognition Chart

USE THIS CHART TO MATCH UP

HARDWARE DURING THE INVENTORY

AND ASSEMBLY PROCESS.

5mm

Flat

Head

Cap

Screw

G0513 Series Bandsaws -17-

Inventory

The following is a list of items shipped with your

machine. Before beginning setup, lay these items

out and inventory them.

If any non-proprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

G0513, G0513P, & G0513ANV

Shipping Inventory (Figures 7–8) Qty

A. Bandsaw (not shown) ................................. 1

B. Table ........................................................... 1

C. Miter Gauge ................................................ 1

D. Rear Rail .................................................... 1

E. Front Rail ................................................... 1

F. Fence Assembly ......................................... 1

G. Guide Post Handwheel............................... 1

Hardware & Tools (Not Shown) Qty

• Eye Bolt M10-1.5 (May Be Installed) .......... 1

• Flat Washers 8mm (Table) ......................... 4

• Lock Washers 8mm (Table) ....................... 4

• Hex Bolts M8-1.25 x 16 (Table) .................. 4

• Hex Bolt M8-1.25 x 90 (Positive Stop) ........ 1

• Hex Nuts M8-1.25 (Positive Stop, Fence)... 2

• Cap Screws M6-1 x 16 (Fence) .................. 2

• Hex Bolts M6-1 x 20 (Fence) ...................... 2

• Lock Washers 6mm (Fence) ...................... 2

• Flat Washers 6mm (Fence) ........................ 2

• Hex Nut M6-1 (Fence) ................................ 1

• Table Pin..................................................... 1

• Table Insert ................................................. 1

• Fence Handle M8-1.25 x 22 (Fence) .......... 1

• Rail Pad M6-1 x 18 (Fence) ........................ 1

• Hex Wrench 5mm, 8mm....................1 Each

• Open-End Wrench 10 x 13mm ................... 1

Figure 8. Other bandsaw components.

Figure 7. Table and miter gauge.

NOTICE

If you cannot find an item on this list, care-

fully check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpack-

ing or they are pre-installed at the factory.

SUFFOCATION HAZARD!

Keep children and pets away

from plastic bags or packing

materials shipped with this

machine. Discard immediately.

-18- G0513 Series Bandsaws

Figure 10. Other bandsaw components.

G0513X2

Shipping Inventory (Figures 9–10) Qty

A. Bandsaw (not shown) ................................. 1

B. Table ........................................................... 1

C. Miter Gauge ................................................ 1

D. Rear Rail .................................................... 1

E. Resaw Fence ............................................ 1

F. Front Rail .................................................... 1

G. Fence Assembly ......................................... 1

H. Guide Post Handwheel............................... 1

Hardware & Tools (Not Shown) Qty

• Eye Bolt M10-1.5 (May Be Installed) .......... 1

• Flat Washers 8mm (Table, Fence, Rail) ..... 5

• Lock Washers 8mm (Table, Rail) ............... 4

• Hex Bolts M8-1.25 x 25 (Table) .................. 4

• Hex Bolt M8-1.25 x 90 (Positive Stop) ........ 1

• Hex Nuts M8-1.25 (Positive Stop, Fence)... 2

• Cap Screws M6-1 x 16 (Rear Rail) ............. 2

• Hex Bolt M6-1 x 20 (Front Rail) .................. 2

• Cap Screw M8-1.25 x 20 (Rail) .................. 1

• Lock Washers 6mm (Rail) .......................... 2

• Flat Washers 6mm (Rail) ............................ 2

• Hex Nut M6-1 (Fence) ................................ 1

• Table Pin..................................................... 1

• Table Inserts ............................................... 2

• Fence Handle M8-1.25 x 44 (Fence) .......... 1

• Rail Pad M6-1 x 18 (Fence) ........................ 1

• Moving Plate (Fence).................................. 1

• Hex Wrench 5mm, 8mm....................1 Each

• Open-End Wrench 10 x 13mm ................... 1

Figure 9. Table and miter gauge.

G0513 Series Bandsaws -19-

Figure 12. Other bandsaw components.

G0513X2F

Shipping Inventory (Figures 11–12) Qty

A. Bandsaw (not shown) ................................. 1

B. Table ........................................................... 1

C. Miter Gauge ................................................ 1

D. Rear Rail .................................................... 1

E. Resaw Fence ............................................ 1

F. Front Rail .................................................... 1

G. Fence Assembly ......................................... 1

H. Guide Post Handwheel............................... 1

I. Foot Brake Pedal ........................................ 1

Hardware & Tools (Not Shown) Qty

• Eye Bolt M10-1.5 (May Be Installed) .......... 1

• Flat Washers 8mm (Table, Fence, Rail) ..... 5

• Lock Washers 8mm (Table, Rail) ............... 4

• Hex Bolts M8-1.25 x 25 (Table) .................. 4

• Hex Bolt M8-1.25 x 90 (Positive Stop) ........ 1

• Hex Nuts M8-1.25 (Positive Stop, Fence)... 2

• Cap Screws M6-1 x 16 (Rear Rail) ............. 2

• Hex Bolt M6-1 x 20 (Front Rail) .................. 2

• Cap Screw M8-1.25 x 20 (Rail) .................. 1

• Lock Washers 6mm (Rail) .......................... 2

• Flat Washers 6mm (Rail) ............................ 2

• Hex Nut M6-1 (Fence) ................................ 1

• Cap Screws M6-1 x 16 (Foot Brake Pad) ... 2

• Lock Washers 6mm (Foot Brake Pad) ....... 2

• Table Pin..................................................... 1

• Table Inserts ............................................... 2

• Fence Handle M8-1.25 x 44 (Fence) .......... 1

• Rail Pad M6-1 x 18 (Fence) ........................ 1

• Moving Plate (Fence).................................. 1

• Hex Wrench 5mm, 8mm....................1 Each

• Open-End Wrench 10 x 13mm ................... 1

Figure 11. Table and miter gauge.

-20- G0513 Series Bandsaws

Figure 14. Other bandsaw components.

G0513X2B, G0513X2BF

Shipping Inventory (Figures 13–12) Qty

A. Bandsaw (not shown) ................................. 1

B. Table ........................................................... 1

C. Miter Gauge ................................................ 1

D. Resaw Fence ............................................. 1

E. Front Rail .................................................... 1

F. Fence Assembly ......................................... 1

G. Guide Post Handwheel............................... 1

H. Foot Brake Pedal ........................................ 1

Hardware & Tools (Not Shown) Qty

• Eye Bolt M10-1.5 (May Be Installed) .......... 1

• Flat Washers 8mm (Table, Fence, Rail) ..... 8

• Lock Washers 8mm (Table, Rail) ............... 5

• Hex Bolts M8-1.25 x 25 (Table) .................. 4

• Hex Bolt M8-1.25 x 90 (Positive Stop) ........ 1

• Hex Nuts M8-1.25 (Positive Stop, Fence)... 2

• Cap Screws M6-1 x 20 (Rail) ..................... 3

• Cap Screw M8-1.25 x 20 (Rail) .................. 1

• Lock Washers 6mm (Rail) .......................... 3

• Flat Washers 6mm (Rail) ............................ 3

• Hex Nut M6-1 (Fence) ................................ 1

• Cap Screws M6-1 x 16 (Foot Brake Pad) ... 2

• Lock Washers 6mm (Foot Brake Pad) ....... 2

• Table Pin..................................................... 1

• Table Inserts ............................................... 2

• Fence Handle M8-1.25 x 44 (Fence) .......... 1

• Moving Plate (Fence).................................. 1

• Rail Plates .................................................. 3

• Hex Wrench 5mm, 8mm....................1 Each

• Open End Wrench 10 x 13mm ................... 1

Figure 13. Table and miter gauge.

G0513 Series Bandsaws -21-

Cleanup Site Considerations

The unpainted surfaces of your machine are

coated with a heavy-duty rust preventative that

prevents corrosion during shipment and storage.

This rust preventative works extremely well, but it

will take a little time to clean.

Be patient and do a thorough job cleaning your

machine. The time you spend doing this now will

give you a better appreciation for the proper care

of your machine's unpainted surfaces.

There are many ways to remove this rust preven-

tative, but the following steps work well in a wide

variety of situations. Always follow the manufac-

turer’s instructions with any cleaning product you

use and make sure you work in a well-ventilated

area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (WD•40 works well)

• Safety glasses & disposable gloves

• Plastic paint scraper (optional)

Basic steps for removing rust preventative:

Put on safety glasses.

Coat the rust preventative with a liberal

amount of cleaner/degreaser, then let it soak

for 5–10 minutes.

Wipe off the surfaces. If your cleaner/degreas-

er is effective, the rust preventative will wipe

off easily. If you have a plastic paint scraper,

scrape off as much as you can first, then wipe

off the rest with the rag.

Repeat Steps 2–3 as necessary until clean,

then coat all unpainted surfaces with a quality

metal protectant to prevent rust.

NOTICE

Avoid chlorine-based solvents, such as

acetone or brake parts cleaner, that may

damage painted surfaces.

Floor Load

Refer to the Machine Data Sheet for the weight

and footprint specifications of your machine.

Some residential floors may require additional

reinforcement to support both the machine and

operator.

Placement Location

Consider existing and anticipated needs, size of

material to be processed through each machine,

and space for auxiliary stands, work tables or

other machinery when establishing a location for

your new machine. See Figure 15 for the mini-

mum working clearances.

Figure 15. Minimum working clearances.

32"

Children and visitors may be

seriously injured if unsuper-

vised around this machine.

Lock entrances to the shop

or disable start switch or

power connection to prevent

unsupervised use.

-22- G0513 Series Bandsaws

Moving & Placing

Bandsaw

Special care should be taken when moving this

bandsaw. Only use one of the following methods

to lift or move this bandsaw.

Using Eye Bolt

1. Move the crate to the prepared location, then

remove the crate from the shipping pallet.

2. Unbolt the bandsaw from the pallet.

3. Install the eye bolt shown (see Figure 16),

make sure it is threaded all the way in, then

place the lifting hook through the eye bolt and

lift the bandsaw slowly with a forklift.

Using Wood Blocks

1. Move the crate to the prepared location, then

remove the crate from the shipping pallet.

2. Unbolt the bandsaw from the pallet.

3. Carefully place the forklift forks under the

head and insert a 1x4 block between the head

and the left fork and a 2x4 block between the

head and right fork so the bandsaw is level,

as shown in Figure 17.

4. Lift the bandsaw off of the pallet, remove the

pallet, then slowly set the bandsaw into posi-

tion.

Note: If you are concerned about your forklift

forks hitting the tension handwheel, remove the

handwheel before positioning the forks, then rein-

stall it after placing.

Figure 16. Lifting the bandsaw.

Eye Bolt

4. Remove the pallet and slowly set the bandsaw

into position.

This bandsaw is a heavy

machine. Serious personal

injury may occur if safe

moving methods are not

used. Get assistance and

use power equipment to

move the shipping crate

and remove the machine

from the shipping pallet.

Figure 17. Example photo of lifting bandsaw with

forklift using wood shims.

2x4 1x4

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

G0513 Series Bandsaws -23-

We recommend mounting your new machine to

the floor. Because floor materials may vary, floor

mounting hardware is not included. You may also

mount your machine to a mobile base that has

wheel locking or wheel retracting capabilities that

keeps the mobile base from rolling when not in

use.

Bolting to Concrete Floors

Lag shield anchors with lag bolts (see Figure 18)

and anchor studs (see Figure 19) are two popular

methods for anchoring an object to a concrete

floor. We suggest you research the many options

and methods for mounting your machine and

choose the best that fits your specific application.

Mounting

Figure 18. Typical lag shield anchor and bolt.

Figure 19. Typical anchor stud.

Anchor studs are stronger and more per-

manent alternatives to lag shield anchors;

however, they will stick out of the floor,

which may cause a tripping hazard if you

decide to move your machine.

Assembly

Installing Guide Post Handwheel,

Positive Stop Bolt, & Table

1. Secure the guide post handwheel onto the

handwheel shaft flat with the included set

screw (see Figure 20).

Figure 20. Guide post handwheel installed.

Guide Post

Handwheel

2. Thread the M8-1.25 hex nut halfway onto the

M8-1.25 x 90 hex bolt (this is the positive stop

bolt).

3. Thread the positive stop bolt into the thread-

ed hole on bandsaw body (see Figure 21).

Figure 21. Positive stop bolt installed.

Positive Stop

-24- G0513 Series Bandsaws

The table is heavy and requires two people

to lift it onto the trunnions. Remove the saw

blade to make table installation easier.

8. Models G0513, G0513P and G0513ANV:

Secure the table to the trunnions, as shown

in Figure 23 with the (4) M8-1.25 x 16 hex

bolts, 8mm lock washers, and 8mm flat wash-

ers.

Models G0513X2, G0513X2B, G0513X2BF,

and G0513X2F: Secure the table to the trun-

nions with the (4) M8-1.25 x 25 hex bolts,

8mm lock washers, and 8mm flat washers.

9. Replace the saw blade.

4. Loosen blade tension by rotating the quick-

release tension lever clockwise, as shown in

Figure 22.

Figure 22. Quick-release tension lever.

Tighten

Loosen

5. Adjust the upper and lower blade guides

away from the blade. Refer to Adjusting

Blade Guides beginning on Page 36 for

more details.

All saw blades are danger-

ous and may cause per-

sonal injury. To reduce the

risk of being injured, wear

leather gloves when han-

dling saw blades.

6. Remove the saw blade (refer to Blade

Changes on Page 51 for detailed instruc-

tions).

7. With the help of another person, lift the table

onto the trunnions.

Figure 23. Mounting the table.

Trunnions

x 4

G0513 Series Bandsaws -25-

Installing Fence (G0513, G0513P,

G0513ANV, G0513X2, & G0513X2F)

1. Attach the rear rail to the table with the (2)

M6-1 x 16 cap screws, as shown in Figure 24.

2. Attach the front rail with the (2) M6-1 x 20 hex

bolts, 6mm lock washers, and 6mm flat wash-

ers, as shown in Figure 24.

3. Install an M8-1.25 hex nut on the fence

handle, then thread the handle into the fence

assembly, as shown in Figure 25. Tighten

the hex nut against the fence pivot block to

secure the handle.

Figure 25. Handle installed on fence assembly.

Hex

Nut

Pivot Block

4. Thread the M6-1 hex nut onto the rail pad,

then thread the rail pad into the rear of the

fence (see Figure 26).

Figure 26. Installed rail pad.

Rail Pad

Hex Nut

5. Pull the fence handle up and place the fence

assembly on the front rail (see Figure 27 for

an example photo).

Figure 27. Example photo of correctly installed

fence.

6. Push the fence handle down to lock the fence

assembly in place.

7. Adjust the rear rail pad until there is an even

gap between the bottom of the fence and the

table, then tighten the rail pad hex nut against

the fence.

Figure 24. Rail installation.

Rear Rail

Front Rail

x 2

-26- G0513 Series Bandsaws

Installing Fence (G0513X2B &

G0513X2BF)

1. Attach the rail plates to the front rail with the

(3) M6-1 x 20 cap screws, 6mm lock wash-

ers, and 6mm flat washers (see Figure 28).

Figure 28. Installing front rail onto table.

Knob

Flat

Washer

8mm

Flat Washer 6mm

Lock Washer 6mm

Lock Washer

8mm

Front Rail

Rail Plate

Cap Screw

M6-1 x 20

Cap Screw

M8-1.25 x 20

2. Attach the outer two rail plates with the round

and elongated mounting holes to the outer

part of the table bottom with (2) M8-1.25 x 20

knobs and 8mm flat washers.

3. Attach the remaining rail plate with the round

mounting holes using (1) M8-1.25 x 20 cap

screw, 8mm lock washer, and 8mm flat

washer (see Figure 28).

4. Thread the fence handle into the fence, then

tighten the hex nut against the fence pivot

block (see Figure 29).

Figure 29. Fence handle components.

Hex Nut

Fence

Handle

5. Install the fence on the left-hand side of the

blade.

6. Place the fence flush against the bandsaw

blade (see Figure 30).

Figure 30. Fence flush with blade.

8. Re-tighten the pointer adjustment nut.

7. Loosen the pointer adjustment nut (see

Figure 31) and set the pointer in line with "0"

on the measurement scale on the rail.

Figure 31. Calibrating fence pointer

(adjustment nut out of view).

Pointer

Pointer Nut

G0513 Series Bandsaws -27-

To Install the resaw fence:

1. Place the 8mm flat washer on the lock handle

(see Figure 33), slide it through the hole in

the fence, then thread the moving plate onto

the end of the lock handle threads.

Figure 33. Attaching resaw fence.

Resaw Fence

Lock Handle

Moving

Plate

2. Slide the resaw fence over the moving plate,

as shown in Figure 33, so the moving plate

fits inside the channel of the resaw fence,

then tighten the lock handle.

Installing Foot Brake Pedal

(G0513X2BF & G0513X2F)

Secure the foot brake pedal to the brake lever

using the (2) M6-1 x 16 cap screws and 6mm lock

washers, as shown in Figure 32.

Figure 32. Foot brake installed.

Brake

Pedal

Installing Resaw

Fence (G0513X2,

G0513X2B,

G0513X2BF, &

G0513X2F)

-28- G0513 Series Bandsaws

Initial Blade Tracking

Blade tracking is primarily affected by the tilt of

the upper wheel, known as “center tracking.”

However, the alignment of both wheels plays an

important part as well (see the Aligning Wheels

instructions on Page 69 for more details).

The wheels on this bandsaw were aligned at the

factory, so center tracking is the only adjustment

that needs to be performed when the saw is

new.

To center track the blade:

1. DISCONNECT BANDSAW FROM POWER!

2. Make sure the upper and lower blade guides

are adjusted away from the blade.

3. Open the upper wheel cover.

4. Engage the quick tension lever, then turn the

blade tension handwheel until the tension

scale (see Figure 34) is between 4 and 6.

Serious personal injury can

occur if the machine starts

while your hand is touch-

ing the bandsaw wheel dur-

ing tracking adjustments.

Disconnect power from the

bandsaw before perform-

ing blade tracking adjust-

ments.

Figure 34. Blade tensioning controls.

Blade Tension

Scale

Blade Tension

Handwheel

Blade Centered

on Peak of Crown

Blade

Centered

Wheel

CENTER TRACKING

Wheel

Figure 35. Center tracking profiles.

5. Spin the upper wheel by hand at least three

times and watch how the blade rides on the

crown of the wheel. Refer to Figure 35 for an

illustration of this concept.

— If the blade rides in the center of the upper

wheel and is centered on the peak of the

wheel crown, then the bandsaw is already

tracking properly and no further adjust-

ments are needed at this time.

— If the blade does not ride in the center of

the upper wheel and is not centered on the

peak of the wheel crown, then continue

with the following steps.

The wheels may have sharp edges and the

blade teeth may extend beyond the edge,

creating a laceration hazard. Be careful

when turning the wheels by hand.

IMPORTANT

Changes made to the blade tension may

change how the blade tracks.

G0513 Series Bandsaws -29-

6. Loosen the lock lever on the back of the

bandsaw (see Figure 36) so that the blade

tracking knob can rotate.

7. Spin the upper wheel with one hand and

rotate the tracking control knob in small

amounts with the other hand until the blade

consistently rides in the center of the bandsaw

wheel tire.

8. Tighten the tracking control lock knob and

close the upper wheel cover.

Note: For the best performance from your saw,

regularly maintain proper tracking of the blade.

Fine tune tracking must be done with the bandsaw

turned ON. This will be explained later in the

Operations section.

Figure 36. Blade tracking controls.

Blade Tracking

Knob

Lock Lever

Figure 37. Squaring table to blade.

5. Adjust the positive stop bolt against the bot-

tom of the table and secure it by tightening

the hex nut against the trunnion bracket.

6. Check the adjustment for accuracy once you

have tightened the hex nut.

7. Loosen the screw on the pointer, but do not

remove it.

8. Align the tip of the pointer with the 0˚ mark on

the table tilt scale, then re-tighten the screw

to secure the setting.

The positive stop allows the table to be quickly

and accurately returned to the horizontal (0˚) posi-

tion after being adjusted to a different angle.

To position the positive stop:

1. DISCONNECT BANDSAW FROM POWER!

2. Adjust the blade tension until the mark on the

blade tension scale is between 4 and 6.

3. Loosen the hex nut that locks the positive

stop bolt in place.

4. Raise the guide post and place a machinist’s

square on the table next to the side of the

blade, as illustrated in Figure 37. Adjust the

table square with the blade, then secure it

with the table tilt lock lever.

Adjusting Positive

Stop

-30- G0513 Series Bandsaws

Figure 38. Dust hose attached to bottom dust

port.

Dust Collection

To connect a dust collection hose:

1. Fit a 4" dust hose over each dust port and

secure them in place with a hose clamp (see

Figure 38).

2. Tug the hoses to make sure they do not

come off.

Note: A tight fit is necessary for proper per-

formance.

Recommended CFM at Dust Port: 400 CFM

Do not confuse this CFM recommendation with

the rating of the dust collector. To determine the

CFM at the dust port, you must consider these

variables: (1) CFM rating of the dust collector,

(2) hose type and length between the dust col-

lector and the machine, (3) number of branches

or wyes, and (4) amount of other open lines

throughout the system. Explaining how to cal-

culate these variables is beyond the scope of

this manual. Consult an expert or purchase a

good dust collection "how-to" book.

DO NOT operate this bandsaw without an

adequate dust collection system. This saw

creates substantial amounts of wood dust

while operating. Failure to use a dust col-

lection system can result in short and long-

term respiratory illness.

Power Cord

Connection

(G0513X2BF &

G0513X2F)

The power cord connection MUST be performed

by an electrician or qualified service personnel.

Items Needed Qty

Cord “ S”-Type, 3-Wire, 14 AWG, 300 VAC,

at least 6 ft. long ......................................... 1

Phillips Screwdriver #2 ...................................... 1

Wire Nuts for (2) 14 AWG Wires ........................ 3

Electrical Tape ................................... As Needed

To connect the power cord to the machine:

1. Attach the required plug to the cord per

the plug manufacturer's instructions (refer

to Power Supply beginning on Page 11 for

specifications and the NEMA plug wiring on

Pages 75– 76).

2. Remove the power supply junction box cover

from the right rear of the bandsaw (see

Figure 39). It is secured by two screws.

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

Figure 39. Power supply junction box on rear of

bandsaw.

Power Supply

Junction Box

Strain

Relief

G0513 Series Bandsaws -31-

3. Loosen the right strain relief on the junction

box, then feed the cord into the box with

enough slack in the wires to make the con-

nections.

4. Re-tighten the strain relief around the cord.

Tug on it to make sure the wires inside the

box will not move.

5. Connect the incoming ground wire to the

ground post, as shown in Figure 40.

6. Secure the two incoming hot wires to the

black and white wires from the bandsaw

with wire nuts, then wrap the nuts and wires

with electrical tape to make sure they will not

come loose.

7. Re-attach the junction box cover.

Power Supply Junction Box

Ground

From

Power Supply

Bandsaw

Strain

Relief

Ground

Figure 40. Incoming power cord connections.

Once the assembly is complete, test run your

machine to make sure it runs properly and is

ready for regular operation.

The test run consists of verifying the following: 1)

The motor powers up and runs correctly, and 2)

the safety disabling mechanism works correctly.

If, during the test run, you cannot easily locate

the source of an unusual noise or vibration, stop

using the machine immediately, then review

Troubleshooting on Page 61.

If you still cannot remedy a problem, contact our

Tech Support at (570) 546-9663 for assistance.

To test run the machine:

1. Make sure that you have successfully com-

pleted the Initial Blade Tracking procedure

on Page 28 before continuing.

2. Make sure you have read the safety instruc-

tions at the beginning of the manual and that

the machine is setup properly.

3. Make sure all tools and objects used during

setup are cleared away from the machine.

4. Connect the machine to the power source.

5. Test the operation of the machine to verify

that it starts and operates correctly.

G0513, G0513P, G0513ANV, & G0513X2

Only

a. Verify that the machine is operating cor-

rectly by pressing the power button.

— When operating correctly, the

machine runs smoothly with little or

no vibration or rubbing noises.

— Investigate and correct strange or

unusual noises or vibrations before

operating the machine further. Always

disconnect the machine from power

when investigating or correcting

potential problems.

Test Run

-32- G0513 Series Bandsaws

G0513X2B, G0513X2F, & G0513X2BF Only

a. Insert the key into the power switch (see

Figure 41), then turn it to the "1".

Figure 41. G0513X2B and G0513X2BF control

panel.

Power Switch

ON Button

OFF Button

b. Verify that the machine is operating cor-

rectly by pressing the ON button.

— When operating correctly, the

machine runs smoothly with little or

no vibration or rubbing noises.

— Investigate and correct strange or

unusual noises or vibrations before

operating the machine further. Always

disconnect the machine from power

when investigating or correcting

potential problems.

c. Press the OFF button to stop the

bandsaw.

d. WITHOUT resetting the OFF button, press

the ON button. The machine should not

start.

— If the machine does start (with the

OFF button pushed in), immediately

disconnect the machine from power.

The OFF button safety feature is not

working correctly. This safety feature

must work properly before proceed-

ing with regular operations. Call Tech

Support for help.

e. Push the OFF button in, then twist it

clockwise so it pops out. When the OFF

button pops out, the switch is reset and

ready for operation (see Figure 42).

OFF Button

Figure 42. Resetting the OFF button.

f. Turn the key in the power switch to "0".

g. Try to turn the machine ON. The bandsaw

should not start.

— If the bandsaw starts, immediately

disconnect the machine from power.

The switch disabling feature is not

working correctly. This safety feature

must work properly before proceed-

ing with regular operations. Call Tech

Support for help.

6. Test the operation of the foot brake:

G0513X2BF & G0513X2F Only

a. Start the bandsaw, then press the foot

brake. The motor should shut off and the

blade should come to a rapid stop.

— If the motor does not stop or the

blade does not come to a rapid stop,

immediately disconnect the machine

from power. The foot brake feature

is not working correctly. This safety

feature must work properly before

proceeding with regular operations.

Call Tech Support for help.

Congratulations! The test run is complete and you

are ready to proceed with the following adjust-

ments before putting the bandsaw into full opera-

tion.

G0513 Series Bandsaws -33-

Tensioning Blade

A properly tensioned blade is essential for mak-

ing accurate cuts, maximizing the life of the

blade, and making other bandsaw adjustments.

However, it will not compensate for cutting prob-

lems caused by too rapid of a feed rate, hardness

variations between workpieces, and improper

blade selection.

Improper blade tension is unsafe, produces

inaccurate and inconsistent results, and

introduces unnecessary wear on bandsaw

components. Over-tensioning the blade

increases the chance of the blade breaking

or wheel misalignment. Under-tensioned

blades wander excessively while cutting

and will not track properly during opera-

tion.

Tensioning the blade according to the blade

tension scale before the Test Run section

gave an approximate tension for completing

the bandsaw setup. The following proce-

dures tension the blade for operation.

Blade tensioning method is a matter of preference.

The flutter method and the deflection method are

described below. Either method safely tensions

the blade. Experience and personal preference

will help you decide which method your prefer.

Optimal cutting results for any workpiece results

from a combination of correct blade selection,

proper blade tension, and a light and even feed

rate.

Flutter Method

1. DISCONNECT BANDSAW FROM POWER!

2. Make sure the blade is properly center track-

ing as instructed in the Initial Blade Tracking

on Page 28.

3. Raise the guide post all the way, and move

the upper and lower blade guides away from

the blade.

4. Engage the blade tension quick-release lever

to apply tension to the blade (see Figure 43).

7. Slowly increase the tension until the blade

stops fluttering, then turn the blade tension

adjustment knob an additional 1⁄8 to 1⁄4 of a

turn.

8. Turn the bandsaw OFF and disconnect it

from power.

9. Note what the tension gauge reads. Use that

as a guide for tensioning that specific blade

in the future.

10. Re-adjust blade guides as described in

Adjusting Blade Guides beginning on Page

36 for your model bandsaw.

Figure 44. Blade tension handwheel.

Blade Tension

Handwheel

5. Connect the bandsaw to power, and turn the

bandsaw ON.

6. Using the blade tension handwheel

(Figure 44), slowly decrease blade tension

until the blade starts to flutter.

Figure 43. Blade tension quick-release lever

(G0513X2 shown).

Blade Tension

Quick-release

Lever

-34- G0513 Series Bandsaws

Deflection Method

The deflection method is more subjective than the

flutter method. Each blade deflects differently and

every user must determine what "moderate pres-

sure" means. The following are general guide-

lines for tensioning the blade with the deflection

method.

To tension the bandsaw blade:

1. DISCONNECT BANDSAW FROM POWER!

2. Make sure the blade is properly tracking as

instructed in the Initial Blade Tracking sec-

tion on Page 28.

3. Raise the guide post all the way, and move

the upper and lower blade guides away from

the blade.

4. Engage the blade tension quick-release lever

to apply tension to the blade. Whenever changing a blade or adjusting

tension and tracking, the upper and lower

blade support bearings and blade guides

must be properly adjusted before perform-

ing cutting operations.

5. Using moderate pressure, push the center of

the blade sideways.

— If the blade deflects approximately 1⁄4", it is

properly tensioned. Proceed to Step 6.

— If the blade deflects less than 1⁄4" it is

over-tensioned. Turn the blade tensioning

handwheel counterclockwise two full turns

and repeat this step.

— If the blade deflects more than 1⁄4", the

blade is under-tensioned. Apply tension to

the blade a small amount and repeat this

step until the blade is properly tensioned.

6. Re-adjust the blade guides as described in

Adjusting Blade Guides beginning on Page

36 for your model bandsaw.

G0513 Series Bandsaws -35-

Adjusting Blade

Support Bearings

Before adjusting the blade support bear-

ings, make sure the blade is tracking prop-

erly (Page 28) and that it is correctly ten-

sioned (Page 33).

Support bearings stop excessive backward deflec-

tion of the blade from the advancing workpiece.

The proper adjustment of the support bearings

is an important part of making accurate cuts and

prevents damage to the blade teeth from contact

with the blade guides.

It is important that the distance of the support

bearing behind the blade is the same as the dis-

tance of the blade guides behind the teeth gullets,

which is typically about 0.016" (see Figure 45).

0.016"

Gap

0.016"

Gap

Support

Bearing

Blade

Guide

Figure 45. Distance settings of upper support

bearings and blade guides.

Tools Needed Qty

Hex Wrench 5mm .............................................. 1

Feeler Gauge 0.016" .................................1 Each

Crisp Dollar Bill (Optional) ................................. 1

Tip: You can use a crisp dollar bill in place of the

feeler gauge for the following procedures. The

thickness of the bill when folded in half twice is

approximately 0.016".

Refer to Figures 46–47 and the following descrip-

tions to become familiar with the controls to adjust

the support bearings. Then, adjust the surface of

the support bearings approximately 0.016" behind

the blade.

Note: The support bearing controls are similar for

all models.

Figure 46. Upper support bearing controls.

Figure 47. Lower support bearing controls.

-36- G0513 Series Bandsaws

Before adjusting the blade guides, make

sure the blade is tracking properly (Page 28)

and that it is correctly tensioned (Page 33).

A. Support Bearing. Stops excessive back-

ward blade deflection from the pressure of

the advancing workpiece.

Note: The flat surface of the upper support

bearing faces the blade. The round edge of

the lower support bearing faces the blade.

B. Upper Support Bearing Shaft. Mounts the

support bearing behind the blade. When the

support bearing shaft cap screw is loose,

move this shaft by hand to adjust the upper

support bearing approximately 0.016" behind

the blade, then re-tighten the shaft cap screw

to secure the setting.

C. Support Bearing Shaft Cap Screw. When

loose, allows distance adjustment of the sup-

port bearing behind the blade.

D. Lower Support Bearing Adjustment Knob.

When the support bearing shaft cap screw is

loose, moves the support bearing toward or

away from the blade. Use this knob to adjust

the lower support bearing approximately

0.016" behind the blade, then re-tighten the

shaft cap screw to secure the setting.

Adjusting Blade

Guides

The blade guides provide side-to-side support

to keep the blade straight while cutting. These

guides are adjustable in two ways—forward-and-

back and side-to-side.

To keep the blade straight while cutting, the blade

guides must be as close to the sides of the blade

without exerting any clamping pressure. This dis-

tance is typically about 0.004".

To prevent damage to the blade teeth as the blade

deflects back while cutting, the guides must be

behind the teeth gullets the same amount as the

support bearing is behind the blade, which is typi-

cally about 0.016" (see Figure 45 on the previous

page for an illustration of this relationship).

Note: Models G0513, G0513P, and G0513ANV

use carbide discs as guides, while the remaining

models use ball bearings.

Important: Although the function and the distance

adjustment of the blade guides is the same for all

the G0513 Series Models, the guide controls are

not all the same. Use the set of instructions on

the following pages that is correct for your model

of bandsaw.

G0513 Series Bandsaws -37-

Adjusting Blade Guides (G0513,

G0513P, & G0513ANV)

Tools Needed Qty

Hex Wrench 5mm .............................................. 1

Feeler Gauge 0.004" ................................1 Each

Crisp Dollar Bill (Optional) ................................. 1

Fine Ruler .......................................................... 1

Tip: You can use a crisp dollar bill in place of the

feeler gauge. The thickness of the bill is approxi-

mately 0.004" .

To adjust the upper blade guides:

1. DISCONNECT BANDSAW FROM POWER!

2. Loosen the thumb screws shown in Figure 48.

Blade

Guide

Tooth

Gullet

Blade

0.016"

Gap

Support

Bearing

Blade

0.016"

Gap

0.016"

Gap

Support

Bearing

Blade

Guides

0.004"

Gap

Blade

Figure 49. Correct gap between guide guides

and blade.

3. By hand, adjust the distance of the guides

approximately 0.004" from the sides of the

blades (see Figure 49), then re-tighten the

thumb screws to secure the setting.

Figure 48. Upper blade guides side-to-side con-

trols.

Blade

Guides

Thumb

Screws

Figure 50. Back of upper blade guides.

Guide Block

Cap Screw

Guide

Block

4. Loosen the guide block cap screw shown in

Figure 50.

-38- G0513 Series Bandsaws

Blade

Guide

Tooth

Gullet

Blade

0.016"

Gap

Support

Bearing

Blade

0.016"

Gap

0.016"

Gap

Support

Bearing

Blade

Guides

0.004"

Gap

Blade

Figure 51. Correct guide alignment behind the

teeth gullets.

5. By hand, slide the guide block to position the

blade guides approximately 0.016" behind

the teeth gullets (see Figure 51), then re-

tighten the guide block cap screw to secure

the setting.

The lower blade guides are adjusted in the same

manner as the upper blade guides. However,

some controls are different. Refer to Figure 52 to

become familiar with these controls.

Figure 52. Lower blade guide controls.

Thumb

Screw

Guide

Block Guide Block

Cap Screw

Make sure that the blade teeth will not con-

tact the guides when the blade is against the

rear support bearing during the cut or the

blade teeth will be damaged.

Adjusting Blade Guide Bearings

(G0513X2, G0513X2B, G0513X2BF, &

G0513X2F)

Tools Needed Qty

Hex Wrench 5mm .............................................. 1

Feeler Gauge 0.004", 0.016" ....................1 Each

Crisp Dollar Bill (Optional) ................................. 1

Tip: You can use a crisp dollar bill in place of the

feeler gauge. The thickness of the bill is approxi-

mately 0.004", and when folded in half twice is

approximately 0.016".

Note: The upper and lower guide bearings are

adjusted in the same manner.

To adjust the upper and lower blade guide

bearings:

1. DISCONNECT BANDSAW FROM POWER!

2. Familiarize yourself with the blade guide con-

trols shown in Figure 53.

Figure 53. Blade guide controls.

Knurled

Knob

Blade Guide

Bearings

Bearing Rotation

Cap Screw

Lateral Rod

Cap Screw

Make sure that the blade teeth will not con-

tact the guide bearings when the blade is

against the rear support bearing during the

cut or the blade teeth will be damaged.

G0513 Series Bandsaws -39-

3. Loosen the lateral rod cap screw and slide

the guide block to position the blade guides

approximately 0.016" behind the blade gul-

lets, as illustrated in Figure 54.

Note: The 0.016" spacing is ideal, although

with larger blades it may not be possible.

In such cases, adjust the guide bearings as

far forward as possible to the blade gullets,

and still maintain the proper support bearing

spacing adjustment.

Blade

Gullet

Guide

Bearings

0.016"

Gap

Figure 54. Lateral adjustment of blade guides.

4. Tighten the lateral rod cap screw to secure

the setting.

5. Loosen both bearing rotation cap screws.

6. Rotate the knurled knob to position the bear-

ings approximately 0.004" away from the

blade.

7. Re-tighten the cap screws to lock the blade

guide bearings in position.

Aligning Table

To ensure cutting accuracy when the table is first

installed, the table should be aligned so that the

miter slot is parallel to the bandsaw blade. This

procedure works best with a wide (3⁄4") blade

installed.

Tools Needed Qty

Straightedge ...................................................... 1

Fine Ruler .......................................................... 1

Square ............................................................... 1

Wrench or Socket 13mm ................................... 1

To align the table so the miter slot is parallel

to the bandsaw blade:

1. Make sure that the blade is tracking properly

and that it is correctly tensioned.

2. DISCONNECT BANDSAW FROM POWER!

3. Loosen the trunnion bolts that secure the

table.

4. Place an accurate straightedge along the

blade. The straightedge should lightly touch

both the front and back of the blade.

Note: Make sure the straightedge does not

go across a tooth.

5. Use a fine ruler to gauge the distance

between the straightedge and the miter slot.

The distance you measure should be the

same at the front and the back of the table

(see Figure 55).

Figure 55. Measuring for miter slot to be parallel

with blade.

-40- G0513 Series Bandsaws

— If the distance is not the same at the front

and back of the table, adjust the table until

it is.

6. Place a square on the table and against the

back of the blade, as shown in Figure 56.

The table should be perpendicular to the

back of the blade.

— If the table is not perpendicular to the back

of the blade, shim the table in the desired

direction by placing washers between the

table and the two trunnions.

7. Re-tighten the trunnion bolts to secure the

settings.

Figure 56. Squaring back of blade and table.

Blade Square

Table

Aligning Fence

To ensure cutting accuracy when the fence is first

installed, the fence should be aligned with the

miter slot.

Tool Needed Qty

Hex Wrench 5mm .............................................. 1

Aligning Fence (G0513, G0513P,

G0513ANV, G0513X2, & G0513X2F)

1. DISCONNECT BANDSAW FROM POWER!

2. Make sure the table is aligned with the blade

(see Aligning Table on the previous page for

detailed instructions).

3. Install the fence next to the miter slot.

4. Loosen the four cap screws located on the

top face of the fence (see Figures 57–58).

Figure 57. G0513, G0513P, & G0513ANV fence

caps screws.

G0513, G0513P, & G0513ANV

Fence Cap Screws

Figure 58. Four fence cap screws.

G0513X2F Fence

Cap Screws

5. Adjust the fence face parallel with the edge of

the miter slot.

6. Tighten the four cap screws, being careful not

to move the fence.

G0513 Series Bandsaws -41-

Aligning Fence (G0513X2B &

G0513X2BF)

1. DISCONNECT BANDSAW FROM POWER!

2. Make sure the table is aligned with the blade

(see Aligning Table on Page 39 for detailed

instructions).

3. Install the fence and lock it in place next to

the miter slot.

4. Loosen the end knobs and the center cap

screw that secure the front rail to the table

(see Figure 59).

Figure 59. Loosen these knobs and cap screw.

Loosen These

6. Tighten the knobs and cap screw that secure

the rail to the table, being careful not to move

the fence.

Figure 60. Example of fence parallel with miter

slot.

5. Adjust the fence face parallel with the edge of

the miter slot, as shown in Figure 60.

Calibrating Miter

Gauge

The miter gauge needs to be calibrated to the

blade when it is first mounted in the miter slot.

Tool Needed Qty

Phillips Screwdriver #2 ...................................... 1

To calibrate the miter gauge:

1. DISCONNECT BANDSAW FROM POWER!

2. Use a square with one edge against the face

of the miter gauge and the other against the

blade side, as shown in Figure 61.

Figure 61. Squaring miter gauge to blade.

3. Loosen the lock knob on the miter gauge

and adjust the face flush with the edge of the

square.

4. Tighten the lock knob, and verify the setting.

Note: Sometimes the tightening procedure

can affect the adjustment.

5. Loosen the screw that secures the angle

pointer, and adjust the pointer to the 0˚ mark

on the scale.

6. Re-tighten the screw to secure the setting.

-42- G0513 Series Bandsaws

SECTION 4: OPERATIONS

Damage to your eyes and lungs could result

from using this machine without proper pro-

tective gear. Always wear safety glasses and

a respirator when operating this machine.

NOTICE

If you have never used this type of machine

or equipment before, WE STRONGLY REC-

OMMEND that you read books, review

industry trade magazines, or get formal

training before beginning any projects.

Regardless of the content in this section,

Grizzly Industrial will not be held liable for

accidents caused by lack of training.

Loose hair, clothing, or

jewelry could get caught

in machinery and cause

serious personal injury.

Keep these items away

from moving parts at all

times to reduce this risk.

Disabling & Locking

Switch (G0513,

G0513P, G0513ANV,

G0513X2)

The switch can be disabled and locked by insert-

ing a padlock through the power button, as

shown in Figure 62. Locking the switch in this

manner can prevent unauthorized operation of

the machine, which is especially important if the

machine is not stored inside an access-restricted

building.

IMPORTANT: Locking the switch with a padlock

only restricts its function. It is not a substitute

for disconnecting power from the machine when

adjusting or servicing.

Children or untrained people can be

seriously injured by this machine. This

risk increases with unsupervised operation.

To help prevent unsupervised operation,

disable and lock the switch before leaving

machine unattended! Place key in a well-

hidden or secure location. Figure 62. Switch disabled by a padlock.

Shaft

Padlock

The padlock shaft diameter is important to

the disabling function of the switch. With

any padlock used to lock the switch, test the

switch after installation to ensure that it is

properly disabled.

G0513 Series Bandsaws -43-

Disabling & Locking

Switch (G0513X2B,

G0513X2BF,

G0513X2F)

Children or untrained people can be killed

or seriously injured by this machine

. This

risk increases with unsupervised operation.

To help prevent unsupervised operation,

remove the key from

the switch before

leaving machine unattended! Place key in a

well-hidden or secure location.

The power switch can be disabled and locked by

removing the key, as shown. Locking the switch

in this manner can prevent unauthorized opera-

tion of the machine, which is especially important

if the machine is not stored inside an access-

restricted building.

IMPORTANT:

Locking the power switch with a

key only restricts its function. It is not a substitute

for disconnecting power from the machine when

adjusting or servicing.

POWER

General Overview

The bandsaw is one of the most versatile wood

cutting tools in the shop. It is capable of perform-

ing many different cutting functions including:

Straight Cuts

• Miters

• Angles

• Compound Angles

• Resawing

• Ripping

• Crosscutting

Irregular Cuts

• Simple and Complex Curves

• Duplicate Parts

• Circles

• Beveled Curves

A properly adjusted and tuned bandsaw can be

safer to operate than most other saws and per-

forms many functions with ease and accuracy.

Basic Cutting Tips

Here are some basic tips to follow when oper-

ating the bandsaw:

• Replace, sharpen, and clean blades as nec-

essary and make adjustments periodically to

keep the saw always running in top condi-

tion.

• Use a light and even feed rate while cutting.

Light contact with the blade will permit easier

line following and prevent undue friction.

• Avoid trying to turn tight corners because this

will twist the blade. Remember, you must saw

around corners.

• Misuse of the saw or using incorrect tech-

niques is unsafe and results in frustration and

poor cuts. Remember—the blade does the

cutting with the operator’s guidance.

-44- G0513 Series Bandsaws

Operation Overview

The purpose of this overview is to provide the nov-

ice machine operator with a basic understanding

of how the machine is used during operation.

Due to the generic nature of this overview, it is

not intended to be an instructional guide. To learn

more about specific operations, read this entire

manual and seek additional training from expe-

rienced machine operators, and do additional

research outside of this manual by reading "how-

to" books, trade magazines, or websites.

To complete a typical operation, the operator

does the following:

1. Examines the workpiece to make sure it is

suitable for cutting.

2. Adjusts the fence away from the blade the

same width of the desired cut or out of the

way for curve cutting and then locks it in

place.

3. Adjusts the table tilt, if necessary, to the cor-

rect angle of the desired cut.

4. Adjusts the blade guide height to not more

than 1" from the top of the workpiece.

5. Checks to make sure the workpiece can safe-

ly pass all the way through the blade without

interference from other objects.

6. Puts on safety glasses.

7. Starts the dust collector and bandsaw.

8. Holds the workpiece firmly and flatly against

both the table and fence, and then pushes

the workpiece into the blade at a steady and

controlled rate until the workpiece moves

completely beyond the blade.

The operator is very careful to keep fingers

away from the blade and uses a push stick to

feed narrow workpieces.

9. Stops the bandsaw.

Workpiece

Inspection

Some wood workpieces are not safe to cut or may

require modification before they are safe to cut.

Before cutting wood, get in the habit of

inspecting all workpieces for the following:

• Material Type: This machine is intended for

cutting natural and man-made wood products,

and laminate covered wood products. Cutting

drywall or cementitious backer board creates

extremely fine dust, which may reduce the

life of the bearings. This machine is NOT

designed to cut metal, glass, stone, tile, etc.

• Foreign Objects: Nails, staples, dirt, rocks

and other foreign objects are often embed-

ded in wood. While cutting, these objects can

become dislodged and hit the operator or

break the blade, which might then fly apart.

Always visually inspect your workpiece for

these items. If they can't be removed, do

NOT cut the workpiece.

• Large/Loose Knots: Loose knots can

become dislodged during the cutting opera-

tion. Large knots can cause blade damage.

Choose workpieces that do not have large/

loose knots or plan ahead to avoid cutting

through them.

• Wet or "Green" Stock: Cutting wood with

a moisture content over 20% causes unnec-

essary wear on the blade and yields poor

results.

• Excessive Warping: Workpieces with exces-

sive cupping, bowing, or twisting are danger-

ous to cut because they are unstable and can

move unpredictably when being cut. DO NOT

cut excessively warped wood.

• Minor Warping: Workpieces with slight cup-

ping can be safely supported if the cupped

side faces the table or fence. On the contrary,

a workpiece supported on the bowed side will

rock during a cut, leading to loss of control.

G0513 Series Bandsaws -45-

Table Tilt

Model Tilt Specifications

G0513, G0513P, G0513ANV ..... 10° left, 45° right

G0513X2 ..................................... 5° left, 45° right

G0513X2B .................................. 5° left, 45° right

G0513X2BF ................................ 5° left, 45° right

G0513X2F ................................... 5° left, 45° right

Remove the positive stop bolt to tilt the table to the

left (as viewed from the front).

Refer to Figures 63–64 to familiarize yourself

with the table tilt controls for your model bandsaw.

Models G0513, G0513P, &

G0513ANV

Figure 63. Table tilt controls

(G0513, G0513P, and G0513ANV rear view).

Table Tilt Knob

Angle Indicator Scale

Located On Opposite Face

Lock

Lever

Models G0513X2, G0513X2B,

G0513X2BF, & G0513X2F

Figure 64. Table tilt controls

(G0513X2, G0513X2B, G0513X2BF, and

G0513X2F, rear view).

Table Tilt

Lever

Lock Lever

Angle Indicator Scale

To tilt the table:

1. DISCONNECT BANDSAW FROM POWER!

2. Loosen the lock lever to enable table move-

ment.

3. Use the table tilt knob/lever to adjust the

angle of the table as displayed on the angle

indicator scale.

4. Secure the table with the lock lever before

continuing operation.

-46- G0513 Series Bandsaws

Guide Post

The guide post connects the upper blade guide

assembly to the bandsaw. The guide post allows

the blade guide assembly to move up or down so

that it is as close to the workpiece as possible for

safety and blade support.

In order to cut accurately and safely, the bottom of

the blade guide assembly must be no more than

1" above the workpiece at all times—this posi-

tioning provides the greatest blade support and

minimizes the amount of moving blade exposed

to the operator.

To adjust the blade guide assembly on the

guide post:

1. DISCONNECT BANDSAW FROM POWER!

2. Make sure that the blade tension, blade track-

ing, support bearings, and blade guides are

adjusted correctly, as previously described in

the SETUP section.

3. Loosen the guide post lock knob shown in

Figure 65.

4. Turn the guide post handwheel to adjust the

upper blade guide assembly to within 1" from

the top of the workpiece.

5. Lock the guide post in place with the lock

knob.

Guide Post

Lock Knob

Guide Post

Handwheel

Figure 65. Guide post controls.

Blade Guide

Assembly

Blade Guard

Guide Post

Fine Tune Tracking

During setup, the blade was tracked without the

machine connected to power. In this procedure,

the bandsaw is turned ON to perform fine tun-

ing of the tracking. Make small changes with the

blade tracking knob as you monitor the effect on

the blade tracking.

To fine tune the tracking:

1. Close the wheel covers and turn the bandsaw

ON.

2. Observe the blade tracking path through

the clear window on the right edge of the

bandsaw, as shown in Figure 66.

Figure 66. Blade tracking window.

3. Using the tracking controls, adjust the blade

so it tracks on the center of the wheel.

4. Tighten the tracking lock to secure the set-

ting.

G0513 Series Bandsaws -47-

Blade Selection

Selecting the right blade for the cutting task

requires knowledge about blade characteristics

and cutting priorities (i.e. speed, finish, etc.).

Blade Terminology

Figure 67. Bandsaw blade components.

A. Kerf: The amount of material removed by the

blade during cutting.

B. Tooth Set: The amount each tooth is bent

left or right along the blade.

C. Gauge: The thickness of the blade.

D. Blade Width: The widest point of the blade

measured from the tip of the tooth to the back

edge of the blade.

E. Tooth Rake: The angle of the tooth face

from a line perpendicular to the length of the

blade.

F. Gullet Depth: The distance from the tooth tip

to the bottom of the curved area (gullet).

G. Tooth Pitch: The distance between tooth

tips.

H. Blade Back: The distance between the bot-

tom of the gullet and the back edge of the

blade.

I. TPI: The number of teeth per inch measured

from gullet to gullet.

Blade Length

Measured by the blade circumference, blade

lengths are specific to each bandsaw. They are

determined by the wheel diameter and distance

between the wheels.

Blade Width

Measured from the back of the blade to the tip

of the blade tooth (the widest point), blade width

is often the first consideration given to blade

selection. Blade width determines the largest and

smallest curve that can be cut, and contributes

to the accuracy of cutting straight—generally the

wider the blade, the straighter it will cut.

Blade Material

Bandsaw blades must meet two requirements:

flexibility and hardness. The flexibility of a blade

allows it to travel on the wheel as a band, while

hardness allows the teeth to cut and hold an

edge. Modern materials technology has allowed

bandsaw blades to meet these requirements in

various ways.

Carbon Steel: These blades are differentially

heat treated to provide hard teeth that will hold an

edge, and yet be flexible in the back.

Carbide Tooth: Extremely hard carbide is either

welded onto or impregnated into the carbon steel

blades, providing superior edge-holding charac-

teristics (see Figure 68).

Carbon Steel

Carbide Impregnated Steel

Figure 68. Carbide-tooth blade composition.

-48- G0513 Series Bandsaws

Bimetal Blade: A strip of high-speed tool steel is

precision welded to a flexible carbon blade, then

teeth are ground into the blade to provide good

edge-holding qualities for blades taking a lot of

abuse (see Figure 69).

Carbon Steel Blade

Weld

High-Speed Steel

Figure 69. Bimetal blade composition.

Tooth Set

Two common tooth sets for wood bandsaw blades

are alternate and raker. Each different type of

tooth set removes material in a different manner,

leaving cuts with different characteristics (see

Figure 70).

Alternate Raker

Figure 70. Common woodcutting bandsaw blade

tooth sets.

Alternate: An all-purpose arrangement where the

teeth are bent evenly left and right of the blade.

Raker: Three teeth in a recurring group—one

bent left, one bent right, and then one that is not

bent. The raker set is ideal for most contour cuts.

Tooth Type

The most common tooth types for wood blades

are shown and described below (see Figure 71).

Standard (or Raker)

Hook (or Claw)

Skip (or Skip Tooth)

Figure 71. Typical tooth types.

G0513 Series Bandsaws -49-

Blade Selection Chart

Cutting Operation Blade Width

Narrow (1⁄8" –1⁄4") Medium (3⁄16"–

1⁄2") Wide (1⁄2"–

3⁄4")

Resawing

Ripping Thin Stock

Ripping Thick Stock

Ripping Round Stock R

Crosscutting Thin Stock R

Crosscutting Thick Stock R

Crosscutting Round Stock R

F MR

F M

Mitre Cut R

F M

Tenons R

Sharp Curves R

Gradual Curves

S F M

Key

Tooth Type Tooth Pitch (Teeth per Inch or TPI)

SF M C

Hook Raker Skip Fine

(14-32 TPI)

Medium

(4-12 TPI)

Coarse

(2-4 TPI)

Use the blade selection chart below as a general guide when selecting a blade for your operation.

-50- G0513 Series Bandsaws

Blade Breakage

Many conditions may cause a bandsaw blade to

break. Blade breakage is unavoidable in some

cases, since it is the natural result of the peculiar

stresses that bandsaw blades must endure.

Blade breakage is also due to avoidable circum-

stances. Avoidable blade breakage is most often

the result of poor care or judgement on the part

of the operator when mounting or adjusting the

blade or support guides.

The most common causes of blade breakage

are:

• Faulty alignment or adjustment of the blade

guides.

• Forcing or twisting a wide blade around a

short radius.

• Feeding the workpiece too fast.

• Dull or damaged teeth.

• Over-tensioned blade.

• Top blade guide assembly set too high above

the workpiece. Adjust the top blade guide

assembly so that there is approximately

1⁄8"–

1⁄4" between the bottom of the assembly

and the workpiece.

• Using a blade with a lumpy or improperly fin-

ished braze or weld.

• Continuously running the bandsaw when not

in use.

• Leaving the blade tensioned when not in

use.

• Using the wrong pitch (TPI) for the workpiece

thickness. The general rule of thumb is to

have not less than two teeth in contact with

the workpiece at all times during cutting.

Blade Care &

Break-In

Blade Care

A bandsaw blade is a thin piece of steel that is

subjected to tremendous strain. You can obtain

longer use from a bandsaw blade if you give it fair

treatment and always use the appropriate feed

rate for your operation.

Be sure to select blades with the proper width,

set, type, and pitch for each application. Using the

wrong blade will produce unnecessary heat and

shorten the life of the blade.

A clean blade will perform much better than a dirty

blade. Dirty or gummed up blades pass through

the cutting material with much more resistance

than clean blades. This extra resistance also

causes unnecessary heat.

Blade Break-In

The sharp teeth tips and edges of a new blade are

extremely sharp, and cutting at too fast of a feed

rate fractures the beveled edges of the teeth and

causes premature blade wear.

To properly break-in a new blade:

1. Choose the correct speed for the blade and

material of the operation.

2. Reduce the feed pressure by half for the first

50–100 in2 of material cut.

3. To avoid twisting the blade when cutting,

adjust the feed pressure when the total width

of the blade is in the cut.

G0513 Series Bandsaws -51-

Blade Changes

All saw blades are danger-

ous and may cause per-

sonal injury. To reduce the

risk of being injured, wear

heavy leather gloves when

handling saw blades.

Figure 73. Placing blade on the wheels.

4. Tighten the blade tension lever.

5. Adjust the blade tension (refer to Page 33)

and blade tracking (refer to Page 46).

6. Adjust the upper/lower guide bearings and

the support bearings (refer to instructions

beginning on Page 35).

7. Close the wheel covers.

8. Replace the table insert and table pin.

Installing Blade

1. DISCONNECT BANDSAW FROM POWER!

2. Slide the blade through the table slot, ensur-

ing that the teeth are pointing down toward

the table.

Note: If the teeth will not point downward

in any orientation, the blade is inside-out.

Remove the blade, and twist it right side-out.

3. Slip the blade through the blade guides, and

mount it on the upper and lower wheels (see

Figure 73).

Blade changes entail removing the existing blade

from the wheel and table, installing the new blade,

then properly adjusting the blade tension and

tracking.

Removing Blade

1. DISCONNECT BANDSAW FROM POWER!

2. Release the blade tension by turning the

blade tension quick-release lever to the left

(see Figure 72).

3. Remove the table insert and the table pin.

Adjust the upper and lower guide bearings as

far away as possible from the blade.

4. Open the upper and lower wheel covers, and

with gloved hands, slide the blade off of both

wheels.

5. Rotate the blade 90˚ and slide it through the

slot in the table to remove it.

Figure 72. Blade changing controls

(G0513X2 shown).

Move This Lever

to the Left

Table Pin

Blade

Guides

Table

Insert

-52- G0513 Series Bandsaws

Blade Speed

The blade speed can be adjusted to 1700 or 3500

FPM. Speed adjustments are made by moving the

V-belt position on the motor and wheel pulleys.

Most woodcutting can be performed successfully

at the higher blade speeds. Slower blade speeds

generally produce better results when cutting

hardwoods, intricate curves, or when an excep-

tionally smooth cut is desired.

Use the chart below as a general guide to

blade speed:

Type of Cutting Operation Blade Speed

(FPM)

Most Species of Wood 3500

Super Dense Hardwood 1700

Fast/Average Feed Rate 3500

Requires Slow Feed Rate 1700

Rough Edges Acceptable 3500

Requires Smooth Edges 1700

Quick, Production Cuts 3500

Detailed, Intricate Cuts 1700

To adjust the blade speed:

1. DISCONNECT BANDSAW FROM POWER!

2. Loosen the motor mount cap screws shown

in Figure 74, and rotate the motor to loosen

the V-belt.

Figure 74. Motor mount cap screws.

3. Refer to Figure 75 to locate the correct V-belt

position for the desired blade speed and

move the V-belt to the indicated pulleys.

3500 FPM

1700 FPM

BANDSAW

WHEEL

MOTOR

WHEEL

Figure 75. V-belt speeds.

Bandsaw

Wheel

3⁄4"

Deflection

Motor

Wheel

Figure 76. V-belt deflection.

4. Rotate the motor to tension the V-belt, then

tighten the motor mount cap screws.

5. Check the V-belt tension by applying mod-

erate pressure between the pulleys (see

Figure 76). If deflection is not approximately

3⁄4", re-tension the V-belt until it is.

G0513 Series Bandsaws -53-

Crosscutting

Crosscutting is the process of cutting across the

grain of wood. For plywood and other processed

wood, crosscutting simply means cutting across

the width of the material.

To make a 90˚ crosscut:

1. Mark the workpiece on the edge where you

want to begin the cut.

2. Adjust the blade guide assembly to no more

than 1" above the workpiece and the miter

gauge to 90°.

3. Move the fence out of the way. Place the

workpiece evenly against the miter gauge.

4. Hold the workpiece against the miter gauge

and line up the mark with the blade.

5. After all safety precautions have been met,

turn the bandsaw ON. Slowly feed the

workpiece into the blade and continue the

cut until the blade is all the way through the

workpiece. Figure 77 shows a typical cross-

cutting operation.

Figure 77. Example of crosscutting.

Resawing (see Figure 78 for an example) is the

process of cutting a board into two or more thinner

boards. The maximum board width that can be

resawn is limited by the maximum cutting height

of the bandsaw.

Blade selection is one of the most important con-

siderations when resawing. Generally, the wider

blade, the better. In most applications, a hook or

a skip tooth style blade with fewer teeth-per-inch

(from 2 to 4) is desirable because they offer larger

gullet capacities for clearing sawdust, decrease

blade heat, and reduce strain on the motor.

Resawing

When resawing thin pieces, a wandering

blade (blade lead) can tear through the sur-

face of the workpiece, exposing your hands

to the blade teeth. Always use push blocks

when resawing and keep your hands clear

of the blade.

Figure 78. Example of resawing.

-54- G0513 Series Bandsaws

To resaw a workpiece:

1. Verify that the bandsaw is setup properly and

that the table is perpendicular to the blade.

2. Use the widest blade your bandsaw will

accept.

Note: The blade must also be sharp and

clean.

3. Install the resaw fence, set it to the desired

width of cut, and lock it in place.

Note: When resawing thin workpieces, set up

the resaw fence in the alternate position, as

shown in Figure 79, and make sure to use a

push stick.

4. Support the ends of the board if necessary.

5. Turn the bandsaw ON.

6. Using push paddles and a push stick, keep

pressure against the fence and table, and

slowly feed the workpiece into the moving

blade until the blade is completely through

the workpiece.

The fence scale will NOT be accurate when

using the resaw fence.

Cutting Curves

When cutting curves, simultaneously feed and

turn the stock carefully so that the blade follows

the layout line without twisting. If a curve is so

abrupt that it is necessary to repeatedly back up

and cut a new kerf, use either a narrower blade

or a blade with more TPI (teeth per inch), or make

more relief cuts.

Always make short cuts first, then proceed to

the longer cuts. Relief cuts will also reduce the

chance that the blade will be pinched or twisted.

Relief cuts are cuts made through the waste

portion of the workpiece and are stopped at the

layout line. As you cut along the layout line, waste

wood is released from the workpiece, alleviating

any pressure on the back of the blade. Relief cuts

also make backing the workpiece out easier, if

needed.

NOTICE

The list below displays blade widths and

the corresponding minimum radii for those

blade widths.

Width Radius

1⁄8" .................................... 1⁄8"

3⁄16" ................................... 3⁄8"

1⁄4'' .................................... 5⁄8''

3⁄8'' .................................... 11⁄4''

1⁄2'' .................................... 21⁄2''

5⁄8'' .................................... 33⁄4''

3⁄4'' .................................... 51⁄2''

Figure 79. Resaw fence installed in the alternate

position.

G0513 Series Bandsaws -55-

Stacked Cuts

One of the benefits of a bandsaw is its ability to

cut multiple copies of a particular shape by stack-

ing a number of workpieces together. Before mak-

ing stacked cuts, ensure that both the table and

the blade are properly adjusted to 90°. Otherwise,

any error will be compounded.

To complete a stacked cut:

1. Align your pieces from top to bottom to

ensure that each piece has adequate scrap

to provide a clean, unhampered cut.

2. Secure all the pieces together in a manner

that will not interfere with the cutting. Hot

glue on the edges works well, as do brad

nails through the waste portion. (Be careful

not to cut into the brads or you may break the

blade!)

3. On the face of the top piece, lay out the

shape you intend to cut.

4. Make relief cuts perpendicular to the out-

line of your intended shape in areas where

changes in blade direction could strain the

woodgrain or cause the blade kerf to bind.

5. Cut the stack of pieces as though you were

cutting a single piece. Follow your layout line

with the blade kerf on the waste side of your

line, as shown in Figure 80.

Figure 80. Example of stack cutting.

-56- G0513 Series Bandsaws

SECTION 5: ACCESSORIES

ACCESSORIES

1311⁄2" Carbon Steel Replacement Blades

Model Width TPI Type Gauge

H4803 1⁄8"14 Raker 0.025

H4804 1⁄4" 6 Hook 0.025

H4805 1⁄4"18 Raker 0.025

H4806 3⁄8"10 Raker 0.025

H4807 1⁄2" 6 Hook 0.025

H4808 1⁄2"10 Raker 0.025

H4809 3⁄4" 3 Hook 0.032

H4810 1" 6Hook 0.035

H4811 1" 2Hook 0.035

1311⁄2" Timber Wolf Carbon Steel Blades

Model Width TPI Type Gauge

H8591 1⁄8"14 HP 0.025

H8592 1⁄4" 4 Pos. Claw 0.025

H8593 1⁄4"10 Raker 0.025

H8594 3⁄8" 4 Pos. Claw 0.025

H8595 3⁄8"10 Raker 0.025

H8596 1⁄2" 3 Pos. Claw 0.025

H8597 1⁄2"10 Raker 0.025

H8598 3⁄4" 3 Thin 0.025

H8599 1" 3 Pos. Claw 0.035

Figure 81. D2057A SHOP FOX® Mobile Base.

D2057A—Heavy-Duty SHOP FOX® Mobile Base

This patented base is the most stable on the mar-

ket with outrigger type supports. Adjusts from 20"

x 201⁄2" to 291⁄2" x 291⁄2". 700 lb. capacity. Weighs

47 lbs.

Installing unapproved accessories may

cause machine to malfunction, resulting in

serious personal injury or machine damage.

To reduce this risk, only install accessories

recommended for this machine by Grizzly.

NOTICE

Refer to our website or latest catalog for

additional recommended accessories.

order online at www.grizzly.com or call 1-800-523-4777

T26544—LED Light w/Mag Base & Flex Arm

This high intensity LED flashlight is ultra-bright

and zoomable, allowing you to focus or disperse

the light. Has three modes: high beam, low beam,

and an emergency flash. Fish eye lens is 1x2000

zoom. Also features a powerful 30 lb. magnetic

base, so you can attach this wherever you need

light. Base has a 9" flexible clamp arm for addi-

tional mobility. Includes the LED light, base, plate,

and 3 AAA batteries.

Figure 82. T26544 LED Light with Base and

Flexible Arm.

G0513 Series Bandsaws -57-

Recommended Metal Protectants

G5562—SLIPIT® 1 Qt. Gel

G5563—SLIPIT® 12 oz Spray

G2871—Boeshield® T-9 12 oz Spray

G2870—Boeshield® T-9 4 oz Spray

H3788—G96® Gun Treatment 12 oz Spray

H3789—G96® Gun Treatment 4.5 oz Spray

Figure 84. Recommended products for protect-

ing unpainted cast iron/steel part on machinery.

D2272—Tilting Roller Stand

Adjusts from 26" to 44", 0º-45º. 150 lb. capacity.

D2273—Single Roller Stand

Adjusts from 26 5⁄8" to 45". 250 lb. capacity.

D2274—5 Roller Stand

Adjusts from 26" to 445⁄8". 250 lb. capacity.

These super heavy-duty roller stands feature con-

venient hand knobs for fast height adjustment.

Figure 86. SHOP FOX® Roller Stands.

D2272

D2273

D2274

Basic Eye Protection

T20501—Face Shield Crown Protector 4"

T20502—Face Shield Crown Protector 7"

T20503—Face Shield Window

T20451—“Kirova” Clear Safety Glasses

T20452—“Kirova” Anti-Reflective S. Glasses

H7194—Bifocal Safety Glasses 1.5

H7195—Bifocal Safety Glasses 2.0

H7196—Bifocal Safety Glasses 2.5

Figure 85. Assortment of basic eye protection.

T20451

T20452

T20502

T20503

H7194

order online at www.grizzly.com or call 1-800-523-4777

T26403—The Missing Shop Manual: Bandsaw

Dedicated to providing integral information about

woodworking tools and techniques that other

manuals overlook, the books in this series contain

safety facts, explanations about basic project set

up, and tips for maximizing tool performance. In

Bandsaw, you will find out how to best utilize this

essential workshop tool, and how to get the most

for your money by getting the most from your

equipment. Filled with clear diagrams and instruc-

tions, this pocket sized durable manual is ideal for

quick reference in the workshop. 112 pages, soft

cover.

Figure 83. The Missing Shop Manual: Bandsaw.

-58- G0513 Series Bandsaws

SECTION 6: MAINTENANCE

Always disconnect power

to the machine before

performing maintenance.

Failure to do this may

result in serious person-

al injury.

For optimum performance from your machine,

follow this maintenance schedule and refer to any

specific instructions given in this section.

Daily Check:

• Loose mounting bolts.

• Worn or damaged saw blade.

• Worn or damaged wires.

• Check/clean wheel brush.

• Clean/protect table surface.

• Check lubrication points.

• Any other unsafe condition.

Monthly Check:

• V-belt tension, damage, or wear.

• Clean/vacuum dust build-up from inside cabi-

net and off motor.

Schedule

Cleaning &

Protecting

Cleaning the bandsaw is relatively easy. Vacuum

excess wood chips and sawdust, and wipe off the

remaining dust with a dry cloth. If any resin has

built up, use a resin dissolving cleaner to remove

it.

Protect the unpainted cast iron surfaces on the

table by wiping it clean after every use—this

ensures moisture from wood dust does not remain

on bare metal surfaces. Keep the table rust-free

with regular applications of products like G96®

Gun Treatment, SLIPIT®, or Boeshield® T-9 (see

Page 57 for more details).

Wheel Brush

The bandsaw is equipped with a lower wheel

brush to keep saw dust from building up on the

tire. The brush should be checked daily and

cleaned when it becomes dirty.

There is an adjustment bracket that allows the

brush to be adjusted for bristle wear (refer to

Adjusting Wheel Brush on Page 66 for detailed

instructions).

Lubrication

An essential part of lubrication is cleaning the

components before lubricating them. This step

is critical because dust and chips build up on

lubricated components, which makes them hard

to move. Simply adding more grease to built-

up grime will not result in smooth moving parts.

Clean the components in this section with an oil/

grease solvent cleaner or mineral spirits before

applying lubrication.

All bearings are sealed and permanently lubri-

cated. Leave them alone until they need to be

replaced.

Blade Post Rack

Lubrication Type ........ GL2 Grease or Equivalent

Amount .................................................Thin Coat

Frequency .......................................... As Needed

To lubricate the blade post rack and pinion:

1. DISCONNECT BANDSAW FROM POWER!

2. Lower the blade guides until they reach the

table.

G0513 Series Bandsaws -59-

3. Using a rag and mineral spirits, wipe off any

existing grease and sawdust build-up on the

rack (see Figure 91).

Figure 91. Example of rack lubrication location.

Rack Exposed

for Lubrication

4. Apply a thin coat of lubricant to the rack.

5. Move the blade post up and down several

times to distribute the lubricant, then remove

any excess grease to help reduce potential

sawdust build-up.

Tension Adjustment Assembly

Lubrication Type ........ GL2 Grease or Equivalent

Amount .................................................Thin Coat

Frequency .......................................... As Needed

To lubricate the tension adjustment assem-

bly:

1. DISCONNECT BANDSAW FROM POWER!

2. Open the top wheel cover and look through

the top of the wheel.

3. Using a rag and mineral spirits, wipe off any

existing grease and sawdust build-up on the

blade tension adjustment assembly and ten-

sion lever cam.

Figure 92. Example of tension adjustment

assembly locations (top wheel removed for

clarity).

Cam

Adjustment

Assembly

Trunnions

Models G0513 and G0513P have steel trunnions

that can be cleaned and lubricated with GL2

grease or equivalent along the sliding surfaces

(see Figure 93) when necessary.

Figure 93. Trunnion lubrication location

(G0513 & G0513P only).

Sliding Surfaces

Models G0513X2, G0513X2B, G0513X2BF, and

G0513X2F have cast iron trunnions that produce

a fine graphite powder over time that acts as a

lubricant. We recommend not adding lubricant

to the trunnions which could make a sticky sub-

stance that would prevent smooth movement.

4. Apply a thin coat of lubricant to the tension

adjustment assembly and tension lever cam

(see Figure 92).

-60- G0513 Series Bandsaws

Review the troubleshooting and procedures in this section if a problem develops with your machine. If

you need replacement parts or additional help with a procedure, call our Technical Support.

Note: Please

gather the serial number and manufacture date of your machine before calling.

SECTION 7: SERVICE

Troubleshooting

Symptom Possible Cause Possible Solution

Machine does not

start or a breaker

trips.

1. Stop button engaged/at fault.

2. Switch disabling key removed.

3. Overload relay in magnetic switch tripped.

4. Wiring break or short; loose connections.

5. Plug or receptacle is corroded or miswired.

6. Power supply off/incorrect voltage.

7. Motor connection wired incorrectly.

8. Contactor has poor contacts or is at fault.

9. Blown fuse/tripped circuit breaker.

10. Power switch at fault.

11. Start capacitor has blown.

12. Centrifugal switch at fault.

13. Motor at fault.

1. Reset/replace button.

2. Re-install switch disabling key.

3. Allow relay to cool. If necessary, reset.

4. Replace broken wires; fix shorts or loose

connections.

5. Correct the wiring.

6. Switch power supply on/verify voltage.

7. Wire motor correctly. Refer to diagram inside junction

box or the wiring diagrams beginning on Page 73.

8. Fix contacts or replace.

9. Replace fuse or reset circuit breaker. If problem is

not due to circuit overload, find/repair short.

10. Replace switch.

11. Test/replace if at fault.

12. Adjust/replace centrifugal switch.

13. Repair or replace.

Machine has

excessive vibration

or noise.

1. V-belt tension incorrect.

2. Bent or dull blade.

3. Loose blade.

4. Blade weld contacting support bearing or

blade guides.

5. Loose machine component.

6. Machine incorrectly mounted on floor.

7. Motor fan rubbing on fan cover.

8. V-belt worn or damaged.

9. Wheels not coplanar.

10. V-belt has a high spot.

11. Pulleys loose or not aligned; shaft bent.

12. Worn wheel bearing.

13. Wheel tires worn.

14. Wheels out of balance.

15. Motor at fault.

1. Re-tension V-belt (Page 64).

2. Replace blade (Page 51).

3. Re-tension blade (Page 33).

4. File/stone the blade weld smooth or round back of

blade.

5. Tighten loose component.

6. Level/shim base; tighten/adjust mounting hardware.

7. Adjust/replace fan cover; replace fan if loose or

damaged.

8. Replace V-belt (Page 64).

9. Adjust wheels coplanar (Page 69).

10. Replace/adjust the V-belt (Page 64).

11. Tighten or re-align pulleys; replace bent shaft.

12. Check/replace wheel bearing.

13. Replace tires.

14. Replace wheels.

15. Repair/replace motor.

G0513 Series Bandsaws -61-

Symptom Possible Cause Possible Solution

Machine stalls

or slows when

operating.

1. Too much pressure against workpiece.

2. Workpiece too moist or unsuitable.

3. Workpiece is warped.

4. Fence incorrectly adjusted.

5. V-belt slipping.

6. Run capacitor at fault.

7. Motor connection wired incorrectly.

8. Motor overheated.

9. Contactor has poor contacts or is at fault.

10. Centrifugal switch at fault.

11. Motor at fault.

1. Decrease the feed rate or workpiece pressure.

2. Only cut wood and ensure moisture is below 20%.

3. Straighten workpiece or use a different one.

4. Adjust/calibrate fence (Page 40).

5. Tension/replace V-belt (Page 64); ensure pulleys

are aligned.

6. Test/repair/replace.

7. Wire motor correctly. Refer to diagram inside junction

box or the wiring diagrams beginning on Page 73.

8. Let cool, clean motor, and reduce workload.

9. Test all legs for power, test field coil, and fix contacts

or replace if at fault.

10. Adjust/replace centrifugal switch if available.

11. Test for shorted windings, bad bearings and repair

or replace.

Miter bar binds in

miter slot.

1. Miter slot dirty or gummed up. 1. Carefully clean miter slot.

Table does not tilt

to 0 degrees.

1. Pointer or scale calibrated incorrectly.

2. Positive stop bolt not set correctly.

1. Calibrate pointer/scale at true 0 degrees.

2. Adjust positive stop bolt (Page 29).

Table does not tilt

to 45 degrees.

1. Pointer or scale calibrated incorrectly.

2. Machine component blocking path.

1. Calibrate pointer/scale at true 45 degrees.

2. Remove component blocking table.

Table hard to tilt. 1. Sawdust or pitch trapped between trunnion

and base.

2. Metal burrs on trunnion.

1. Clean/lubricate sliding surfaces of trunnions

(Page 60).

2. Remove burrs.

Cuts are rough or

show scoring.

1. Blade is overloaded and twists.

2. Blade TPI is too coarse or speed incorrect.

3. Blade is loose and slipping on wheels.

4. Blade tracking is incorrect.

5. Blade has missing or bent teeth.

6. Blade has a faulty weld.

1. Decrease the feed rate or workpiece pressure.

2. Use correct blade for application (Page 47).

3. Re-tension blade (Page 33).

4. Adjust blade tracking (Page 28) or adjust wheels

coplaner (Page 69).

5. Replace the blade (Page 51).

6. Replace the blade (Page 51).

Blade or teeth

break.

1. Blade tension too high.

2. Incorrect blade for application.

3. Feed rate or blade speed is too fast.

4. Operator is cutting corners too sharply.

5. Blade is dull.

6. Blade tracking is wrong.

7. Blade guides adjusted incorrectly.

8. Inadequate blade support near cutting

area.

9. Blade weld at fault.

10. Wheel tires worn or damaged.

11. Fence or miter slot not aligned with blade.

1. Decrease blade tension (Page 33).

2. Use correct blade for application (Page 47).

3. Reduce feed rate or increase blade speed.

4. Use a wider arc on outside cuts, or use relief cuts to

make tight inside cuts.

5. Replace blade (Page 51).

6. Adjust blade tracking (Page 46).

7. Re-adjust blade guides (Page 36).

8. Adjust upper blade guide closer to workpiece

(Page 36).

9. Replace blade (Page 51).

10. Replace tires.

11. Align miter slot and fence with blade (Page 39).

-62- G0513 Series Bandsaws

Symptom Possible Cause Possible Solution

Blade wears on one

side, slows, smokes

or shows signs of

overheating.

1. Blade contacting table insert.

2. Blade guides are mis-adjusted or worn.

3. Blade has insufficient support near cutting

area.

4. Blade installed backwards.

5. Too much side pressure when feeding

workpiece.

6. Wheels are out of alignment.

7. Dull or incorrect blade for workpiece.

8. Blade is bell-mouthed.

9. Fence not parallel with blade (pressure at

blade backside).

10. Table top is not square with blade.

1. Re-adjust blade guides (Page 36) to eliminate side

pressure. Adjust table for correct blade clearance

and miter slot alignment (Page 39).

2. Adjust/replace blade guides.

3. Adjust upper blade guide closer to workpiece

(Page 36).

4. Properly install blade with teeth pointing down.

5. Feed workpiece straight into the blade.

6. Adjust wheels so they are coplanar (Page 69).

7. Replace blade (Page 51).

8. Install new blade.

9. Adjust fence parallel with blade (Page 40).

10. Adjust/shim table/trunnion position until blade and

table are parallel and square (Page 39).

Sawdust build-up

inside cabinet.

1. Clogged dust port(s).

2. Low CFM (airflow) from dust collection

system.

1. Clean out dust port(s).

2. Repair ducting for leaks or clogs, move dust collector

closer to machine, install a stronger dust collector.

Blade tracks

incorrectly, or

comes off wheels.

1. Tracking is not adjusted properly.

2. Wheels are not coplanar.

3. Blade tension is too loose.

4. Blade guides not adjusted correctly.

5. Feed rate too fast.

6. Incorrect blade for bandsaw.

7. Blade is bell-mouthed, worn or dull.

8. Rubber tire on wheel is damaged or worn.

1. Adjust tracking (Page 46).

2. Adjust wheel coplanarity (Page 69).

3. Increase blade tension (Page 33).

4. Adjust blade guides (Page 36).

5. Decrease feed rate.

6. Install correct blade for machine.

7. Install new blade/de-tension blade when not in use.

8. Replace rubber tires.

Cut is crooked, or

the blade wanders

(blade lead).

1. Feed rate is too fast or blade speed is

incorrect.

2. Blade tension is low.

3. Blade is dull or damaged.

4. Inadequate blade support.

5. Incorrect blade for application.

6. Blade is tracking incorrectly.

7. Table is loose.

8. Fence/miter slot out of alignment.

9. Blade guides mis-adjusted.

1. Adjust feed rate and cutting speed as required.

2. Increase the blade tension (Page 33).

3. Replace blade (Page 51).

4. Adjust upper blade guide closer to workpiece

(Page 36).

5. Use wider blade.

6. Adjust blade tracking (Page 28) (Page 46).

7. Tighten table mounting bolts or tilt lock lever.

8. Align table miter slot and fence with blade

(Page 39).

9. Adjust blade guides (Page 36).

G0513 Series Bandsaws -63-

V-Belt Service

Checking V-Belt

To ensure optimum power transmission from the

motor to the blade, the V-belt must be in good

condition and properly tensioned. The belt should

be free of cracks, fraying, and wear. Belt tension

and condition should be checked at least every

3 months—more often if the bandsaw is used

daily.

To check V-belt tension:

1. DISCONNECT BANDSAW FROM POWER!

2. Open the lower wheel cover.

3. Check the condition of the V-belt. If the V-belt

is cracked, frayed, or glazed, replace it.

4. Check the V-belt tension by applying mod-

erate pressure between the pulleys (see

Figure 94). If deflection is not approximately

3⁄4", re-tension the V-belt following the same

steps you normally use when changing blade

speeds (refer to Blade Speed on Page 52 if

necessary).

Bandsaw

Wheel

3⁄4"

Deflection

Motor

Wheel

Figure 94. V-belt deflection.

To replace the V-belt:

1. DISCONNECT BANDSAW FROM POWER!

2. Open both wheel covers, and remove the

blade (refer to Blade Changes on Page 51).

3. Unthread the lower wheel mount bolt shown

in Figure 95, and slide the lower wheel off

the bearing shaft.

Figure 95. Example of wheel mount bolt.

Wheel Mount Bolt

5. Slip the old V-belt off of the wheel pulley and

install the new V-belt in its place.

6. Properly tension the V-belt and re-tighten the

motor mount cap screws.

7. Re-install the lower wheel back and secure it

with the wheel mount bolt.

8. Re-install the blade and close the wheel cov-

ers.

Figure 96. Motor mount cap screws.

4. Loosen the motor mount cap screws shown

in Figure 96.

Replacing V-Belt

To replace the V-belt, you must remove the blade

and the lower wheel. After re-installation, you

must properly re-tension the V-belt.

Tools Needed: Qty

Hex Wrench 6mm ...............................................1

Hex Wrench 8mm ...............................................1

-64- G0513 Series Bandsaws

"Blade Lead" means that the blade does not cut

straight when using the fence or miter gauge (see

Figure 97). This is a common condition with all

bandsaws. Worn or damaged blades may cause

lead and replacing them will fix the problem. Still, if

your bandsaw is setup correctly and lead occurs,

compensate for it by skewing the fence.

Figure 97. Example of blade leading away from

line of cut.

To correct blade lead, do the following steps

and make a test cut before skewing the

fence:

1. Ensure that you have proper blade tension

(refer to Page 33).

2. Ensure that the blade guides are adjusted

correctly (refer to Pages 36–39).

3. Ensure that the fence (refer to Page 40) and

miter gauge (refer to Page 41) is parallel to

the blade.

To skew your fence:

1. Cut a piece of scrap wood approximately 3⁄4"

thick x 3" wide x 17" long. On a wide face of

the board, draw a straight line parallel to the

long edge.

Blade Lead 2. Slide the fence out of the way and cut free-

hand along the line. Stop at the halfway point.

Turn the bandsaw OFF and wait for the blade

to come to a complete stop.

3. Clamp the board to the bandsaw table with-

out moving it. Now slide the fence over to

the board so it barely touches one end of

the board.

4. Loosen the four cap screws on top of the

fence.

5. Skew the fence as needed until it is paral-

lel to the edge of the scrap piece. You may

need to re-adjust the fence locking mecha-

nisms to gain maximum adjustment.

6. While maintaining the skew, re-tighten the

fence cap screws.

To compensate for lead when making straight

crosscuts with the miter gauge, you will need

to shift the table:

1. Set the miter gauge to 90°.

2. On a scrap piece of wood, mark a line that

is perpendicular to the front edge. Starting

where the line begins, cut the board by

pushing it through the blade with the miter

gauge.

3. Loosen the table mounting bolts, and shift

the table to compensate for the blade lead.

4. Repeat Steps 1–3 until the blade cuts

straight when wood is pushed through with

the miter gauge.

If the table is shifted, the fence will be

affected since it is attached.

Lead adjustments will change when new

blades are mounted on the saw.

G0513 Series Bandsaws -65-

Adjusting Wheel

Brush

The lower wheel has a brush, as shown in Figure

98, that is designed to sweep sawdust off the

wheel tire as the wheel rotates. In order to work

properly, the brush must make firm contact with

the wheel.

Tools Needed: Qty

Wrench/Socket 10mm ........................................2

To adjust the brush:

1. DISCONNECT BANDSAW FROM POWER!

2. Open the lower wheel cover.

3. Loosen the bolt and nut that secures the

brush in place.

4. Adjust the brush so it makes firm, even con-

tact with the wheel—without bending the

bristles.

5. Tighten the bolt and nut to secure the brush

in place.

Figure 98. A wheel brush.

Wheel Brush

Adjusting Tension

Lever

The quick-release tension lever was setup at the

factory for use with the pre-installed 131

1⁄2" blade.

However, if you install a different length blade,

you will need to adjust the quick-release adjust-

ment screw so that the quick-release lever works

correctly.

Keep in mind that actual blade lengths may vary

slightly by manufacture.

Tools Needed: Qty

Hex Wrench 5mm .............................................. 1

Wrench 10mm ................................................... 1

To adjust the quick-release lever:

1. DISCONNECT BANDSAW FROM POWER!

2. Open the wheel covers and install a new

blade.

3. Loosen the jam nut on the tension adjustment

screw 7-10 turns (see Figure 99).

4. Engage the quick-release lever, then turn the

blade tension handwheel until the blade ten-

sion matches the mark on the blade tension

scale for the appropriate blade width.

5. Thread the tension adjustment screw (see

Figure 99) down until it contacts the wheel

block plate, then back it off 1-2 turns.

6. Re-tighten the jam nut.

Figure 99. Example of quick-release tension

lever adjustment screw.

Wheel Block

Plate

Tension

Adjustment

Screw

Jam Nut

-66- G0513 Series Bandsaws

Adjusting Guide

Post Travel

The guide post assembly should remain paral-

lel with the blade front-to-back and side-to-side

along its length of travel. If it does not, follow these

instructions to adjust it.

Important: Make sure the table is aligned with the

blade from side-to-side and front-to-back before

beginning these procedures (refer to Aligning

Table on Page 39 for detailed instructions).

Tools Needed:

Machinist's Square ............................................ 1

Small Ruler ........................................................ 1

Hex Wrench 4mm .............................................. 1

Hex Wrench 5mm .............................................. 1

Metal Shims ..................................... (As Needed)

Checking/Adjusting Guide Post

Parallel with Blade Side-to-Side

1. DISCONNECT BANDSAW FROM POWER!

2. Loosen the guide post lock knob, lower the

guide post to within 1" of the table top, then

tighten the knob.

3. Place a machinist's square on the table next

to the right hand side of the guide post, as

shown in Figure 100.

Guide Post (Front View)

Figure 100. Example of checking guide post

squareness.

—If there is no gap between the square and

the guide post along its full length, no

adjustments need to be made. Proceed to

the next procedure.

—If there is a gap between the square and

the guide post, the guide post is not parallel

to the blade. Go to Step 4.

4. Loosen each of the four screws shown in

Figure 101 1⁄4 turn.

Figure 101. Guide post adjustment screws.

5. Gently tap the lower part of the guide post in

the appropriate direction until there is no gap

between the square and the guide post.

6. Tighten the screws shown in Figure 101.

G0513 Series Bandsaws -67-

Checking/Adjusting Guide Post

Parallel with Blade Front-to-Back

1. DISCONNECT BANDSAW FROM POWER!

2. Loosen the guide post lock knob, lower the

blade guide assembly to within 1" of the table

top, then tighten the lock knob.

3. Remove the screws that secure the guide

post guard and move it up and out of the

way.

4. Measure the distance "A" between the upper

front face of the guide post rack and the back

of the blade (see Figure 102).

Distance "A"

Distance "B"

(Right Side View)

Guide Post

Blade

Figure 102. Example of measuring distance

between rack and blade at top of guide post.

5. Measure the distance "B" between the bot-

tom front face of the guide post rack and the

back of the blade (see Figure 102).

—If the measurements taken in Steps 4–5

are equal, no adjustments need to be

made. Go to Step 9.

—If the measurements taken in Steps 4–5

are not equal, go to Step 6.

6. Place the guide post guard on top of the

guide post assembly so you can access the

guide post bracket.

7. Loosen the four screws shown in Figure 101

on the previous page enough to fit metal

shims between the frame and the guide post

bracket (see Figure 103).

—If the guide post to blade distance is greater

at the bottom than at the top, place a shim

between the bottom of the bracket and the

frame (Shim "A"). This will tilt the bottom of

the guide post toward the blade.

—If the guide post to blade distance is less

at the bottom than at the top, place a shim

between the top of the bracket and the

frame (Shim "B"). This will tilt the bottom of

the guide post away from the blade.

Shim "B"

(Left Side View)

Shim "A"

Frame

Blade

Guide

Post

Guide

Bracket

Figure 103. Location for placing shims.

8. Tighten the four screws shown in Figure 101

on the previous page, then repeat Steps 4–5.

—If the measurements are equal, go to

Step 9.

—If the measurements are not equal, con-

tinue adding shims as needed until guide

post rack to blade distance is the same at

the top and bottom.

9. Re-install the guide post guard with the

screws removed in Step 3.

-68- G0513 Series Bandsaws

Aligning Wheels

Components and Hardware Needed: Qty

56" Long 2x4 ..................................................... 1

Tools Needed:

Hex Wrenches 4 & 6 mm .............................1 Ea

Wrench 13mm ................................................... 1

Tape Measure .................................................... 1

Coplanarity Gauge (see Figure 104) ................ 1

Straightedge ........................................................

Fine Ruler .......................................................... 1

Wheel alignment is one of the most critical factors

for optimal performance from your bandsaw.

Heat, vibration, wandering, blade wear, tire wear

and overall bandsaw wear are considerably

decreased when the wheels are properly aligned

or “coplanar.”

Coplanar wheels automatically track the blade

by balancing it on the crown of the wheel. This is

known as coplanar tracking.

Checking Coplanarity

1. Make the "Coplanarity Gauge" shown in

Figure 104.

Note: For best results, straighten the 2x4

with a jointer before cutting.

2. DISCONNECT BANDSAW FROM POWER!

3. Remove the fence and open both wheel cov-

ers.

4. Adjust the blade guides away from the blade,

loosen blade tension, remove the table insert

and pin, then remove the blade.

5. Remove the table.

6. Reinstall the blade, making sure the guide

bearings and support bearings are away from

the blade, then tighten your blade to the ten-

sion that it will be used during operation.

7. Place your coplanarity gauge up against both

wheels in the positions shown in Figure 105.

Coplanarity

Gauge Gauge Positions

Tracking

Knob

Adjustment

Hub

Wheels

Figure 105. Checking for coplanarity.

Figure 104. Dimensions of coplanarity gauge.

Side View

56"

3-1⁄2"

17"

22"

1-1⁄2"

G0513 Series Bandsaws -69-

— If the wheels are coplanar (Figure 107, A),

the straightedge will evenly touch the top

and bottom of both wheels.

— If the wheels are not coplanar (Figure 107,

B), place the straightedge on the lower

wheel first (ensuring that it touches both

the top and bottom rim), then adjust the

upper wheel tracking knob to make the

upper wheel coplanar and parallel with the

lower wheel.

— If the straightedge does not touch both

wheels evenly, the upper wheel needs to

be shimmed (Figure 107, D) or the lower

wheel needs to be adjusted (Figure 107,

C).

Shimming Upper Wheel

1. DISCONNECT BANDSAW FROM POWER!

2. Make sure the top wheel is adjusted parallel

with the bottom wheel.

3. With a straightedge touching both points of

the wheel that does not need to be adjusted,

measure the distance away from the wheel

that is out of adjustment (see Figure 106).

Coplanar

Parallel, Not

Coplanar

Not Coplanar

Gauge

Contacts Top

And Bottom of

Both Wheels

Gauge Only

Contacts Bottom

Wheel

Gauge Only

Contacts Bottom

Wheel. Top Wheel

Needs to Be Tilted.

Gauge Contacts

Wheels Unevenly

Coplanarity Gauge

Solution:

Shim Upper

Wheel Out

Not Parallel

Not Coplanar

Solution:

Adjust

Lower

Wheel

Hub

Solution:

Adjust

Tracking

Knob

Figure 107. Coplanar diagram.

Figure 106 Determining distance needed to

shim upper wheel.

Wheel Out of

Adjustment

Difference Between

Wheels 6. Replace the wheel, the original washers, the

securing screw, and the blade.

7. Tighten the blade, then check the wheels with

the coplanarity gauge. (Wheel coplanarity

changes as the blade is tightened, so it is

best to check the wheel alignment when the

blade is tensioned as it would be for normal

operations.)

4. Remove the blade from the saw, then remove

the wheel that needs to be shimmed.

5. Determine how many shim washers you need

to compensate for the distance measured in

Step 3 and place them on the wheel shaft.

-70- G0513 Series Bandsaws

8. When the wheels are coplanar, place a mark

on each wheel where you held the straight-

edge. This assures repeated accuracy every

time you adjust your wheels.

Note: When wheels are properly coplanar,

the blade may not be centered on the crown

of the wheel, but it will be balanced.

Adjusting Lower Wheel

Only do this procedure if you cannot make the

wheels coplanar with the tracking knob or by

shimming the upper wheel. Make sure the upper

wheel is adjusted as close as possible to being

coplanar with the lower wheel before beginning.

Do this procedure with the blade fully tensioned.

To adjust the lower wheel:

1. DISCONNECT BANDSAW FROM POWER!

2. Loosen the jam nuts on the lower wheel

adjustment hub (see Figure 108).

Figure 108. Lower wheel adjustment control.

Top Tilt

Side

Tilt

Bottom Tilt

Side

Tilt

Adjustment

Hub

3. Loosen one tilt adjustment set screw, then

tighten the opposing set screw approximately

an equal amount.

4. Check the wheels with the coplanarity gauge,

then adjust the lower wheel at the hub as

needed until it is parallel and coplanar with

the top wheel.

5. Tighten the jam nuts to lock the tilt adjust-

ment set screws in position.

The space between the magnetic motor brake

and brake shoe is preset by the factory at 0.008"

(0.2mm). To compensate for this wear, you should

adjust this space every two to three years, or if

the brake takes over five seconds for to stop the

motor.

Tools Needed

Phillips Head Screwdriver .................................. 1

Feeler Gauge 0.008" ......................................... 2

Dollar Bill, Folded Once (Optional) .................... 1

Hex Wrench 3mm .............................................. 1

Hex Wrench 4mm .............................................. 1

To adjust the magnetic brake:

1. DISCONNECT BANDSAW FROM POWER!

2. Remove the motor fan cover, then loosen the

cap screws securing the motor fan and brake

shoe (see Figure 109).

Magnetic Brake

Adjustment

(G0513X2B,

G0513X2BF)

3. Place the feeler gauge (or dollar bill folded

once) between the brake shoe and magnetic

brake on either side.

4. Tighten the cap screws on the brake shoe

and motor fan, remove the feeler gauge, then

reinstall the motor fan cover.

Figure 109. Adjusting distance between

magnetic brake and brake shoe.

Magnetic

Brake

Cap

Screw

Motor

Fan

Brake

Shoe

Optional

Dollar Bill

OFF

G0513 Series Bandsaws -71-

SHOCK HAZARD. Working on wiring that is con-

nected to a power source is extremely dangerous.

Touching electrified parts will result in personal

injury including but not limited to severe burns,

electrocution, or death. Disconnect the power

from the machine before servicing electrical com-

ponents!

MODIFICATIONS. Modifying the wiring beyond

what is shown in the diagram may lead to unpre-

dictable results, including serious injury or fire.

This includes the installation of unapproved after-

market parts.

WIRE CONNECTIONS. All connections must

be tight to prevent wires from loosening during

machine operation. Double-check all wires dis-

connected or connected during any wiring task to

ensure tight connections.

CIRCUIT REQUIREMENTS. You MUST follow

the requirements at the beginning of this manual

when connecting your machine to a power source.

WIRE/COMPONENT DAMAGE. Damaged wires

or components increase the risk of serious per-

sonal injury, fire, or machine damage. If you notice

that any wires or components are damaged while

performing a wiring task, replace those wires or

components.

MOTOR WIRING. The motor wiring shown in

these diagrams is current at the time of printing

but may not match your machine. If you find this

to be the case, use the wiring diagram inside the

motor junction box.

CAPACITORS/INVERTERS. Some capacitors

and power inverters store an electrical charge for

up to 10 minutes after being disconnected from

the power source. To reduce the risk of being

shocked, wait at least this long before working on

capacitors.

EXPERIENCING DIFFICULTIES. If you are expe-

riencing difficulties understanding the information

included in this section, contact our Technical

Support at (570) 546-9663.

Wiring Safety Instructions

The photos and diagrams

included in this section are

best viewed in color. You

can view these pages in

color at www.grizzly.com.

These pages are current at the time of printing. However, in the spirit of improvement, we may make chang-

es to the electrical systems of future machines. Compare the manufacture date of your machine to the one

stated in this manual, and study this section carefully.

If there are differences between your machine and what is shown in this section, call Technical Support at

(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated

wiring diagram may be available. Note: Please gather the serial

number and manufacture date of your

machine before calling. This information can be found on the main machine label.

SECTION 8: WIRING

machine

-72- G0513 Series Bandsaws

READ ELECTRICAL SAFETY

ON PAGE 72!

Hot

Ground

6-15 Plug

(As Recommended)

Motor @220V

Power Switch

(viewed from behind)

Motor @110V

220

VAC

START

STOP

220 VAC

Ground

Rewired to 110V

S. Cap 300M 250V

Rewired to 110V

R. Cap 40M 250V

S. Cap 300M 250V

R. Cap 40M 250V

Hot

Neutral

Ground

110 VAC

L5-30 Plug

(As Recommended)

G0513, G0513P, G0513ANV, & G0513X2

Wiring Diagram

G0513 Series Bandsaws -73-

READ ELECTRICAL SAFETY

ON PAGE 72!

G0513X2B Wiring Diagram

CONTROL PANEL

(viewed from behind)

MAGNETIC

SWITCH

Ground

220V MOTOR

Ground

Hot

6-15 PLUG

220 VAC

Magnetic Brake

YZG

Run

Capacitor

45MFD

450VAC

Ground

T1/2 T3/6 NO14

T2/4

L1/1 L3/5 NO13

L2/3

NC15

SDE

NC16

SDE

MA-18

AMP

RESET

96 98

1/2 3/4 5/6 8

SDE

RA-20

8-12

14 13

OFF

14 13

22 21

PWR

22 21

Rectifier

PU-23-2

Ground

-74- G0513 Series Bandsaws

READ ELECTRICAL SAFETY

ON PAGE 72!

G0513X2BF Wiring Diagram

Hot

Ground

220V 6-15 Plug

(As Recommended)

220

VAC

RESET

96 98

1/2 3/4

L1/1 L3/5 NO13L2/3

5/6

NC15

T1/2 T3/6

T2/4

NC16

NO14

22 21

14 13

22 21

14 13

22 21

14 13

Power Supply Junction Box

Magnetic Switch Assembly Control Panel

(Viewed from Behind)

Foot Brake

Switch

Contactor

SDE MA-18

Power

OFF

Motor

Set at

10A

Magnetic

Brake YZG

Rectifier PU-23-2

OL Relay

SDE RA-20

Ground

Ground Ground

Run Capacitor

45MFD 400VAC

Ground

G0513 Series Bandsaws -75-

READ ELECTRICAL SAFETY

ON PAGE 72!

G0513X2F 220V Wiring Diagram

Hot

Ground

220V 6-15 Plug

(As Recommended)

220

VAC

RESET

96 98

1/2 3/4

L1/1 L3/5 NO13L2/3

5/6 8

NC15

T1/2 T3/6

T2/4

NC16

NO14

22 21

14 13

22 21

14 13

22 21

14 13

Power Supply Junction Box

Magnetic Switch Assembly Control Panel

(Viewed from Behind)

Foot Brake Switch

Conctactor

SDE MA-09

Power

OFF

220V

Motor

Set at

10A

OL Relay

SDE RA-20

Ground

Start Capacitor

300MFD 250VAC

Run Capacitor

40MFD 250VAC

-76- G0513 Series Bandsaws

READ ELECTRICAL SAFETY

ON PAGE 72!

G0513X2F 110V Wiring Diagram

RESET

96 98

1/2 3/4

L1/1 L3/5 NO13L2/3

5/6 18

NC15

T1/2 T3/6

T2/4

NC16

NO14

22 21

14 13

22 21

14 13

22 21

14 13

Power Supply Junction Box

Magnetic Switch Assembly Control Panel

(Viewed from Behind)

Foot Brake Switch

Conctactor

SDE MA-18

Power

OFF

110V

Motor

Set at

20A

Ground

OL Relay

SDE RA-30

Ground

Run Capacitor

40MFD 250VAC

Start Capacitor

300MFD 250VAC

Neutral

Ground

110 VAC

L5-30 Plug

(As Recommended)

G0513 Series Bandsaws -77-

32 34

55V2 (G0513ANV)

55A

55AV2 (G0513ANV)

175

39 40

176 39

64 88

61 152

63152

84 83

11-1

5V2 (G0513ANV)

67 59

82-2

82-1

82-3

82-4

82-5

82-6

82-7

82-8

82-9A

82-9

82-10 82-11

95V2 (G0513ANV)

119

43V2 (G0513ANV)

G0513/G0513P/G0513ANV Main

SECTION 9: PARTS

We do our best to stock replacement

parts when possible, but we cannot

guarantee that all parts shown are avail-

able for purchase. Call (800) 523-4777

or visit www.grizzly.com/parts to check

for availability.

-78- G0513 Series Bandsaws

G0513/G0513P/G0513ANV Main Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

4 P0513004 LIFTING EYE BOLT M10-1.5 58 P0513058 WHEEL BRUSH

5 P0513005 MACHINE BODY (G0513) 59 P0513059 HEX BOLT M6-1 X 25

5 P0513P005 MACHINE BODY (G0513P) 60 P0513060 STAR KNOB

5V2 P0513ANV005V2 MACHINE BODY V2.04.17 (G0513ANV) 61 P0513061 LOCK NUT M6-1

8 P0513008 FLAT WASHER 6MM 62 P0513062 STRAIN RELIEF 16MM STRAIGHT LT

9 P0513009 POWER CORD 14G 3W 72" 63 P0513063 HEIGHT POINTER

10 P0513010 HEX NUT M6-1 64 P0513064 HEX NUT M8-1.25

11 P0513011 POINTER 65 P0513065 HEX BOLT M8-1.25 X 100

12 P0513012 STEP SCREW M4-.7 X 5 66 P0513066 STAR KNOB BOLT M10-1.5 X 20

13 P0513013 HINGE SHAFT 67 P0513067 STAR KNOB BOLT M10-1.5 X 55

14 P0513014 ROLL PIN 5 X 36 68 P0513068 THREADED HANDLE M10-1.5

15 P0513015 UPPER WHEEL SHAFT HINGE 69 P0513069 CAM

16 P0513016 UPPER WHEEL SHAFT 70 P0513070 PILLOW BLOCK

17 P0513017 BUSHING 71 P0513071 HANDLE M12-1.75

18 P0513018 BALL BEARING 6204-2RS 72 P0513072 LEVER

19 P0513019 UPPER WHEEL 17" 73 P0513073 HEX NUT M12-1.75

20 P0513020 INT RETAINING RING 47MM 74 P0513074 LEVER HUB

21 P0513021 WHEEL FLAT WASHER 8MM 75 P0513075 CAP SCREW M8-1.25 X 20

22 P0513022 HEX BOLT M8-1.25 X 30 76 P0513076 LOCK WASHER 8MM

23 P0513023 SAW BLADE 131.5" X 1/2" 6TPI HOOK 78 P0513078 SHAFT COVER

24 P0513024 LOCK WASHER 8MM 79 P0513079 SET SCREW M8-1.25 X 20

25 P0513025 HEX BOLT M6-1 X 30 80 P0513080 HEX NUT M8-1.25

26 P0513026 URETHANE TIRE 17" 1-PAIR 81 P0513081 LOWER WHEEL SHAFT

27 P0513027 LOWER WHEEL 17" 82 P0513082 MOTOR 2HP 110V/220V 1-PH

28 P0513028 LOWER WHEEL PULLEY 82-1 P0513082-1 MOTOR FAN COVER

29 P0513029 HEX NUT 1-14 82-2 P0513082-2 MOTOR FAN

30 P0513030 LOCK WASHER 1" 82-3 P0513082-3 S CAPACITOR 300M 250V 1-1/2 X 2-3/8

31 P0513031 MOTOR CORD 14G 3W 82-4 P0513082-4 S CAPACITOR COVER

32 P0513032 COMPRESSION SPRING 7 X 8 X 90 82-5 P0513082-5 R CAPACITOR 40M 250V 1-1/2 X 2-3/4

33 P0513033 ROLL PIN 3 X 16 82-6 P0513082-6 R CAPACITOR COVER

34 P0513034 ALIGNMENT PLATE 82-7 P0513082-7 MOTOR JUNCTION BOX

35 P0513035 THRUST BEARING 51201 82-8 P0513082-8 CONTACT PLATE

36 P0513036 2-BUTTON POWER SWITCH 82-9 P0513082-9 CENTRIFUGAL SWITCH 5/8-1725

37 P0513037 TENSION HANDWHEEL 82-9A P0513082-9A CENTRIFUGAL SWITCH W/CONT PLATE

38 P0513038 TENSION ADJUSTING ROD 82-10 P0513082-10 BALL BEARING 6203ZZ

39 P0513039 FLANGE SCREW M5-.8 X 10 82-11 P0513082-11 BALL BEARING 6205ZZ

40 P0513040 EXT TOOTH WASHER 5MM 83 P0513083 HEX BOLT M5-.8 X 16

41 P0513041 HEX NUT M5-.8 84 P0513084 LOCK WASHER 5MM

42 P0513042 FLANGE SCREW M5-.8 X 16 85 P0513085 MOTOR MOUNT BRACKET

43 P0513043 SWITCH BACK PLATE 86 P0513086 CAP SCREW M8-1.25 X 20

43V2 P0513043V2 SWITCH BACK PLATE V2.04.17 (G0513ANV) 87 P0513087 STRAIN RELIEF PLATE 2-HOLE

44 P0513044 HEX BOLT M8-1.25 X 16 88 P0513088 FLANGE SCREW M5-.8 X 10

45 P0513045 FLAT WASHER 8MM 89 P0513089 PILLOW BLOCK

46 P0513046 UPPER WHEEL SLIDING BRACKET 90 P0513090 KEY 5 X 5 X 35

47 P0513047 HEX BOLT M6-1 X 25 91 P0513091 HEX BOLT M8-1.25 X 20 LH

48 P0513048 STEEL BLIND RIVET 3 X 13MM 92 P0513092 MOTOR PULLEY TYPE-A 3.5"

49 P0513049 HEX BOLT M6-1 X 10 93 P0513093 V-BELT A42

50 P0513050 CLEAR WINDOW 94 P0513094 HEX BOLT M6-1 X 10

55 P0513055 UPPER WHEEL COVER (G0513) 95 P0513095 LOWER WHEEL COVER (G0513)

55 P0513P055 UPPER WHEEL COVER (G0513P) 95 P0513P095 LOWER WHEEL COVER (G0513P)

55V2 P0513ANV055V2 UPPER WHEEL COVER V2.04.17 (G0513ANV) 95V2 P0513ANV095V2 LOWER WHEEL COVER V2.04.17 (G0513ANV)

55A P0513X2055A UPPER WHEEL COVER ASSY (G0513) 97 P0513097 FLAT WASHER 8MM

55A P0513P055A UPPER WHEEL COVER ASSY (G0513P) 119 P0513119 FLAT WASHER 8MM

55AV2 P0513ANV055AV2 UPPER WHEEL COVER ASSY V2.04.17 (G0513ANV) 152 P0513152 HEX BOLT M6-1 X 20

56 P0513056 HEX BOLT M6-1 X 10 175 P0513175 HEX BOLT M6-1 X 20

57 P0513057 FLAT WASHER 6MM 176 P0513176 BUSHING

G0513 Series Bandsaws -79-

G0513/G0513P/G0513ANV Table, Trunnion, &

Lower Blade Guides

REF PART # DESCRIPTION REF PART # DESCRIPTION

77 P0513077 LOCK WASHER 8MM 118 P0513118 LOCK HANDLE M8-1.25

96 P0513096 FLAT WASHER 8MM 119 P0513119 FLAT WASHER 8MM

98 P0513098 CAP SCREW M10-1.5 X 35 120 P0513120 POINTER

99 P0513099 HEX NUT M10-1.5 121 P0513121 TRUNNION PLATE

100 P0513100 TRUNNION GEAR 122 P0513122 LOCK WASHER 8MM

101 P0513101 STAR KNOB BOLT 123 P0513123 CAP SCREW M8-1.25 X 16

102 P0513102 TRUNNION SUPPORT BRACKET 124 P0513124 CARRIAGE BOLT M8-1.25 X 80

103 P0513103 LOCK WASHER 10MM 126 P0513126 TABLE 17" X 17" (G0513/G0513P)

104 P0513104 FLAT WASHER 10MM 126 P0513ANV126 TABLE 17" X 17" (G0513ANV)

105 P0513105 CAP SCREW M6-1 X 15 127 P0513127 TABLE INSERT

106 P0513106 CAP SCREW M6-1 X 50 128 P0513128 TABLE PIN

107 P0513107 ALIGNMENT ROD 129 P0513129 HEX BOLT M8-1.25 X 20 LH

108 P0513108 HEX NUT M6-1 130 P0513130 LEFT GUARD

109 P0513109 ADJUSTMENT KNOB BOLT M6-1 131 P0513131 THUMB SCREW M6-1 X 16

110 P0513110 BALL BEARING 6000ZZ 132 P0513132 LOWER BLADE GUIDE SUPPORT

111 P0513111 BUTTON HD CAP SCR M10-1.5 X 20 133 P0513133 BLADE GUIDE

112 P0513112 FLAT WASHER 8MM 134 P0513134 GUIDE ADJUSTMENT SHAFT

113 P0513113 FLAT WASHER 8MM 135 P0513135 RIGHT GUARD

114 P0513114 PHLP HD SCR M4-.7 X 6 139 P0513139 CAP SCREW M10-1.5 X 30

115 P0513115 GEAR PLATE 148 P0513148 CARRIAGE BOLT M8-1.25 X 85

116 P0513116 LOCK NUT M8-1.25 163 P0513163 LOCK WASHER 8MM

117 P0513117 PHLP HD SCR M4-.7 x 6 196 P0513196 STEEL BALL 5MM

113

110

105

116

106

163 103

104

102

100 139

101

111

103

107

109

108

120

121

122

148 123

119

114

115

112

113

118

124

117

129 130

133

132

134

135

196

131

128

126

127

-80- G0513 Series Bandsaws

G0513/G0513P/G0513ANV Fence

REF PART # DESCRIPTION REF PART # DESCRIPTION

125 P0513125 FENCE ASSEMBLY W/RAILS 214 P0513214 REAR FENCE RAIL

201 P0513201 FRONT FENCE RAIL 215 P0513215 HEX NUT M6-1

202 P0513202 FENCE BASE 216 P0513216 FLANGE SCREW M4-.7 X 6

203 P0513203 ALIGNMENT SHAFT 217 P0513217 FRONT RAIL END CAP

204 P0513204 LOCK BLOCK SHAFT 218 P0513218 FENCE END CAP

205 P0513205 SPRING PLATE 219 P0513219 REAR RAIL END CAP

206 P0513206 SPACER PLATE 220 P0513220 TAP SCREW M3.5 X 8

207 P0513207 FENCE 221 P0513221 FENCE SCALE

208 P0513208 SLEEVE 222 P0513222 HEX NUT M6-1

209 P0513209 FENCE LOCK HANDLE 223 P0513223 LOCK WASHER 6MM

210 P0513210 RAIL PAD 225 P0513225 HEX BOLT M6-1 X 20

211 P0513211 CONVEX WINDOW 226 P0513226 FLANGE SCREW M4-.7 X 10

212 P0513212 CAP SCREW M6-1 X 55 227 P0513227 FLAT WASHER 6MM

213 P0513213 LOCK CAM

204

213

215

209 226

205 203

202

216

211

212

208

207

218

220

222

210

206

214

125

219

201

221

227

225

223

220217

G0513 Series Bandsaws -81-

G0513/G0513P/G0513ANV Upper Blade

Guides & Miter Gauge

165 174V2

150

160

137

142

136

140

141

145

144

143

147

134

146

149

171

138

138-1

172

168

170

169

163

167

166

162

161V2

163

164V2

153

151

149

154

155

149

159

157

157A

156

158

173

173-8

173-7

173-1

173-9

173-3

173-5

192

193

194

173-4

173-6 173-2

-82- G0513 Series Bandsaws

G0513/G0513P/G0513ANV Upper Blade

Guides & Miter Gauge Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

6 P0513006 SET SCREW M5-.8 X 5 160 P0513160 PINION GEAR STEP BOLT

134 P0513134 GUIDE ADJUSTMENT SHAFT 161V2 P0513161V2 THREADED BUSHING V2.06.09

136 P0513136 CAP SCREW M8-1.25 X 80 162 P0513162 CAP SCREW M8-1.25 X 20

137 P0513137 FLAT WASHER 8MM 163 P0513163 LOCK WASHER 8MM

138 P0513138 UPPER BLADE GUARD (G0513/G0513P) 164V2 P0513164V2 THREADED GUIDE BRACKET 14MM V2.06.09

138 P0513ANV138 UPPER BLADE GUARD (G0513ANV) 165 P0513165 WORM CYLINDER

138-1 P0513138-1 BLADE GUARD SCALE 166 P0513166 FIXED PLATE

140 P0513140 STEP SCREW M4-.7 X 5 167 P0513167 PINION GEAR 15T

141 P0513141 FIBER WASHER 5MM 168 P0513168 PINION GEAR STEP BOLT

142 P0513142 SLIDING PLATE (G0513/G0513P) 169 P0513169 BRACKET COVER

142 P0513ANV142 SLIDING PLATE (G0513ANV) 170 P0513170 CAP SCREW M8-1.25 X 16

143 P0513143 EXT RETAINING RING 15MM 171 P0513171 PHLP HD SCR M4-.7 X 8

144 P0513144 BALL BEARING 6202ZZ 172 P0513172 SET SCREW M6-1 X 16

145 P0513145 UPPER BLADE GUIDE SUPPORT 173 P0513173 MITER GAUGE ASSY

146 P0513146 BLADE GUIDE 173-1 P0513173-1 GUIDE BAR

147 P0513147 THUMB SCREW M6-1 X 16 173-2 P0513173-2 T-SLOT WASHER 5MM

149 P0513149 CAP SCREW M6-1 X 15 173-3 P0513173-3 INDICATOR

150 P0513150 ADJUSTMENT SHAFT 173-4 P0513173-4 NYLON WASHER 1/4"

151 P0513151 UPPER SPACING SLEEVE 173-5 P0513173-5 MITER GAUGE HANDLE 1/4"-20

153 P0513153 UPPER GUIDE SUPPORT BLOCK 173-6 P0513173-6 MITER GAUGE BODY

154 P0513154 PHLP HD SCR M4-.7 X 10 173-7 P0513173-7 INDEXING PIN

155 P0513155 HEX NUT M4-.7 173-8 P0513173-8 PHLP HD SCR M6-1 X 6

156 P0513156 RACK 173-9 P0513173-9 FLANGE SCREW M5-.8 X 8

157A P0513157A GUIDE POST ASSEMBLY 174V2 P0513174V2 HEX NUT M16-1.5 THIN

157 P0513157 GUIDE POST 192 P0513192 HEX WRENCH 5MM

158 P0513158 ELEVATION HANDWHEEL 193 P0513193 HEX WRENCH 8MM

159 P0513159 HEX BOLT M6-1 X 20 194 P0513194 WRENCH 10 X 13MM OPEN-END

G0513 Series Bandsaws -83-

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

REF PART # DESCRIPTION REF PART # DESCRIPTION

177 P0513177 MACHINE ID LABEL 184 P0513184 GRIZZLY NAMEPLATE-SMALL

178 P0513178 ELECTRICITY LABEL 185 P0513185 SAW TENSION LABEL

179 P0513179 SAFETY GLASSES LABEL 186 P0513186 MODEL NUMBER LABEL

180 P0513180 READ MANUAL LABEL 187 P0513187 GRIZZLY GREEN TOUCH-UP PAINT

181 P0513181 HANDS/BS BLADE LABEL 188 P0513188 LIGHT GRAY REF PAINT

182 P0513182 DONT OPEN LABEL 189 P0513189 GUIDE POST ADJUST LABEL

183 P0513183 UNPLUG BANDSAW LABEL 190 P0513190 BS BLADE ENCLOSURE LABEL

G0513 Labels

182

183

190

181

189

182

184

186

177

179

180

178

188

187

178

185

-84- G0513 Series Bandsaws

G0513P Labels

REF PART # DESCRIPTION REF PART # DESCRIPTION

177 P0513P177 MACHINE ID LABEL 184 P0513P184 GRIZZLY NAMEPLATE- LARGE

178 P0513P178 ELECTRICITY LABEL 186 P0513P186 MODEL NUMBER LABEL

179 P0513P179 SAFETY GLASSES LABEL 187 P0513P187 GRIZZLY GREEN TOUCH-UP PAINT

180 P0513P180 READ MANUAL LABEL 188 P0513P188 PB WHITE TOUCH-UP PAINT

181 P0513P181 HANDS/BS BLADE LABEL 189 P0513189 GUIDE POST ADJUST LABEL

182 P0513P182 DONT OPEN LABEL 191 P0513P191 POLAR BEAR LOGO

183 P0513P183 UNPLUG BANDSAW LABEL 192 P0513P192 GRIZZLY.COM LABEL

182

179

189

181

183

182

187

192

191

188

178

180

177

186

184

G0513 Series Bandsaws -85-

G0513ANV Labels

REF PART # DESCRIPTION REF PART # DESCRIPTION

177V2 P0513ANV177V2 MACHINE ID LABEL V2.04.17 186 P0513ANV186 MODEL NUMBER LABEL

178 P0513ANV178 ELECTRICITY LABEL 187V2 P0513ANV187V2 TOUCH-UP PAINT, 35TH ANV ED. V2.04.17

179 P0513ANV179 SAFETY GLASSES/RESPIRATOR LABEL 188 P0513ANV188 ORANGE TOUCH-UP PAINT, PANTONE 151C

180 P0513ANV180 READ MANUAL LABEL 189 P0513ANV189 GUIDE POST ADJUST LABEL

182 P0513ANV182 DONT OPEN LABEL 191V2 P0513ANV191V2 GRIZZLY LOGO NAMEPLATE V2.04.17

183 P0513ANV183 UNPLUG BANDSAW LABEL 192 P0513ANV192 ORANGE GRIZZLY.COM LABEL

185 P0513ANV185 SAW TENSION LABEL 194V2 P0513ANV194V2 35TH ANNIVERSARY LABEL V2.04.17

182

189

183

182

187V2

186

194V2

191V2

177V2

178

188

180

179

185

192

-86- G0513 Series Bandsaws

G0513X2 Main

32 33

3534 2

111

39 40

36 42

37 41

64 88 39

111

55A

68 67

69 74

82-2V2

82-1V2

82-4V2

82-3V2

82-7V2

82-6V2

82-5V2 82-8

82-9

82-10

82-11

95A

97 92

119

17-1

17-2

17-3

17-4

17-5

18-1

18-2

18-3

18-4

18-5

83 82V2

G0513 Series Bandsaws -87-

G0513X2 Main Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

2 P0513X2002 SET SCREW M6-1 X 10 55 P0513X2055 UPPER WHEEL COVER

3 P0513X2003 BUSHING 56 P0513X2056 HEX BOLT M6-1 X 25

4 P0513X2004 LIFTING EYE BOLT M10-1.5 57 P0513X2057 FLAT WASHER 6MM

5 P0513X2005 MACHINE BODY 58 P0513X2058 WHEEL BRUSH

7 P0513X2007 BUSHING 59 P0513X2059 CAP SCREW M6-1 X 25

8 P0513X2008 FLAT WASHER 6MM 60 P0513X2060 STAR KNOB

9 P0513X2009 POWER CORD 14G 3W 72" 61 P0513X2061 LOCK NUT M6-1

10 P0513X2010 HEX NUT M6-1 62 P0513X2062 STRAIN RELIEF 16MM STRAIGHT LT

11 P0513X2011 POINTER 63 P0513X2063 HEIGHT POINTER

12 P0513X2012 STEP SCREW M4-.7 X 5 64 P0513X2064 HEX NUT M8-1.25

13 P0513X2013 HINGE SHAFT 65 P0513X2065 HEX BOLT M8-1.25 X 90

14 P0513X2014 ROLL PIN 5 X 36 66 P0513X2066 STAR KNOB BOLT M10-1.5 X 20

15 P0513X2015 UPPER WHEEL SHAFT HINGE 67 P0513X2067 STAR KNOB BOLT M10-1.5 X 55

16 P0513X2016 UPPER WHEEL SHAFT 68 P0513X2068 THREADED HANDLE M10-1.5

17 P0513X2017 UPPER WHEEL ASSEMBLY 69 P0513X2069 CAM

17-1 P0513X2017-1 BUSHING 70 P0513X2070 PILLOW BLOCK

17-2 P0513X2017-2 BALL BEARING 6204-2RS 71 P0513X2071 HANDLE M12-1.75

17-3 P0513X2017-3 INT RETAINING RING 47MM 72 P0513X2072 LEVER

17-4 P0513X2017-4 UPPER WHEEL 17" 73 P0513X2073 HEX NUT M12-1.75

17-5 P0513X2017-5 URETHANE TIRE 17" 1-PAIR 74 P0513X2074 LEVER HUB

18 P0513X2018 LOWER WHEEL ASSEMBLY 75 P0513X2075 BUTTON HD CAP SCR M8-1.25 X 20

18-1 P0513X2018-1 BUSHING 76 P0513X2076 LOCK WASHER 8MM

18-2 P0513X2018-2 BALL BEARING 6204-2RS 78 P0513X2078 SHAFT COVER

18-3 P0513X2018-3 INT RETAINING RING 47MM 79 P0513X2079 SET SCREW M8-1.25 X 20

18-4 P0513X2018-4 LOWER WHEEL 17" 80 P0513X2080 HEX NUT M8-1.25

18-5 P0513X2018-5 URETHANE TIRE 17" 1-PAIR 81 P0513X2081 LOWER WHEEL SHAFT

21 P0513X2021 WHEEL FLAT WASHER 8MM 82V2 P0513X2082V2 MOTOR 2HP 110V/220V 1-PH V2.01.10

22 P0513X2022 CAP SCREW M8-1.25 X 16 82-1V2 P0513X2082-1V2 MOTOR FAN COVER V2.01.10

23 P0513X2023 SAW BLADE 131.5" X 1/2" 6TPI HOOK 82-2V2 P0513X2082-2V2 MOTOR FAN V2.01.10

24 P0513X2024 LOCK WASHER 8MM 82-3V2 P0513X2082-3V2 S CAPACITOR 300M 250V 1-1/2 X 2-3/8 V2.01.10

25 P0513X2025 CAP SCREW M8-1.25 X 20 82-4V2 P0513X2082-4V2 S CAPACITOR COVER V2.01.10

28 P0513X2028 LOWER WHEEL PULLEY 82-5V2 P0513X2082-5V2 R CAPACITOR 40M 250V 1-3/8 X 2-5/8 V2.01.10

29 P0513X2029 HEX NUT 1-14 82-6V2 P0513X2082-6V2 R CAPACITOR COVER V2.01.10

30 P0513X2030 LOCK WASHER 1" 82-7V2 P0513X2082-7V2 MOTOR JUNCTION BOX V2.01.10

31 P0513X2031 MOTOR CORD 14G 3W 82-8 P0513X2082-8 CONTACT PLATE 5/8

32 P0513X2032 COMPRESSION SPRING 7 X 8 X 90 82-9 P0513X2082-9 CENTRIFUGAL SWITCH 5/8-1725

33 P0513X2033 ROLL PIN 3 X 16 82-10 P0513X2082-10 BALL BEARING 6203ZZ

34 P0513X2034 ALIGNMENT PLATE 82-11 P0513X2082-11 BALL BEARING 6205ZZ

35 P0513X2035 THRUST BEARING 51201 83 P0513X2083 HEX BOLT M10-1.5 X 25

36 P0513X2036 2-BUTTON START/STOP SWITCH 84 P0513X2084 LOCK WASHER 10MM

37 P0513X2037 TENSION HANDWHEEL 85 P0513X2085 MOTOR MOUNT BRACKET

38 P0513X2038 TENSION ADJUSTING ROD 86 P0513X2086 BUTTON HD CAP SCR M8-1.25 X 20

39 P0513X2039 FLANGE SCREW M5-.8 X 10 87 P0513X2087 STRAIN RELIEF PLATE 2-HOLE

40 P0513X2040 EXT TOOTH WASHER 5MM 88 P0513X2088 FLANGE SCREW M5-.8 X 10

41 P0513X2041 HEX NUT M5-.8 89 P0513X2089 PILLOW BLOCK

42 P0513X2042 FLANGE SCREW M5-.8 X 16 90 P0513X2090 KEY 5 X 5 X 35

43 P0513X2043 SWITCH BACK PLATE 91 P0513X2091 HEX BOLT M8-1.25 X 20 LH

44 P0513X2044 CAP SCREW M8-1.25 X 16 92 P0513X2092 MOTOR PULLEY TYPE-A 3.5"

45 P0513X2045 FENDER WASHER 8MM 93 P0513X2093 V-BELT A42

46 P0513X2046 UPPER WHEEL SLIDING BRACKET 94 P0513X2094 CAP SCREW M6-1 X 10

47 P0513X2047 CAP SCREW M8-1.25 X 50 95A P0513X2095A LOWER WHEEL COVER

48 P0513X2048 STEEL BLIND RIVET 3 X 13MM 97 P0513X2097 FENDER WASHER 8MM

49 P0513X2049 CAP SCREW M6-1 X 10 111 P0513X2111 CAP SCREW M6-1 X 20

50 P0513X2050 CLEAR WINDOW 119 P0513X2119 LOCK WASHER 4MM

55A P0513X2055A UPPER WHEEL COVER ASSY

-88- G0513 Series Bandsaws

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

REF PART # DESCRIPTION REF PART # DESCRIPTION

201 P0513X2201 MODEL NUMBER LABEL 209 P0513X2209 ELECTRICITY LABEL

202 P0513X2202 GRIZZLY LOGO PLATE 210 P0513X2210 EXTREME SERIES PLATE

203 P0513X2203 OPEN DOOR LABEL 211 P0513X2211 DISCONNECT POWER LABEL

204 P0513X2204 GUARD ADJ LABEL 212 P0513X2212 OPEN DOOR LABEL

205 P0513X2205 SCALE DIRECTIONS LABEL 213 P0513X2213 PUTTY TOUCH-UP PAINT

206 P0513X2206 SAFETY GLASSES LABEL 214 P0513X2214 TENSION ADJ LABEL

207 P0513X2207 HANDS/BLADE LABEL 215 P0513X2215 GRIZZLY GREEN TOUCH-UP PAINT

208 P0513X2208 READ MANUAL LABEL 216 P0513X2216 MACHINE ID LABEL

201 202

203

204

205

216

206

207

208

209

210

211

212

213

214

209

215

G0513X2 Labels

G0513 Series Bandsaws -89-

G0513X2B Main

17-1

17-2

17-3

17-4

17-5

18-1

18-2

18-3

18-4

18-5

29 30

32 33 34 35

38 39

55A

61 93

119

111

19-8

19-1

19-2

19-3

19-9

19-5V2

19-6V2

19-7

177

176

82-10

82-11

82-12

82-1382-14 82-15

82-2

82-3

82-4

82-5V2

82-6

82-9

-90- G0513 Series Bandsaws

G0513X2B Main Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

2 P0513X2B002 SET SCREW M6-1 X 10 41 P0513X2B041 START BUTTON

3 P0513X2B003 BUSHING 44 P0513X2B044 CAP SCREW M8-1.25 X 16

4 P0513X2B004 LIFTING EYE BOLT M10-1.5 45 P0513X2B045 FENDER WASHER 8MM

5 P0513X2B005 MACHINE BODY 46 P0513X2B046 UPPER WHEEL SLIDING BRACKET

7 P0513X2B007 BUSHING 47 P0513X2B047 CAP SCREW M6-1 X 25

8 P0513X2B008 FLAT WASHER 6MM 48 P0513X2B048 STEEL BLIND RIVET 3 X 13MM

10 P0513X2B010 HEX NUT M6-1 49 P0513X2B049 CAP SCREW M6-1 X 10

11 P0513X2B011 POINTER 50 P0513X2B050 CLEAR WINDOW

12 P0513X2B012 STEP SCREW M4-.7 X 5 51 P0513X2B051 KEY SWITCH

13 P0513X2B013 HINGE SHAFT 55A P0513X2B055A UPPER WHEEL COVER ASSY

14 P0513X2B014 ROLL PIN 5 X 35 55 P0513X2B055 UPPER WHEEL COVER

15 P0513X2B015 UPPER WHEEL SHAFT HINGE 56 P0513X2B056 HEX BOLT M6-1 X 25

16 P0513X2B016 UPPER WHEEL SHAFT 57 P0513X2B057 FLAT WASHER 6MM

17 P0513X2B017 UPPER WHEEL ASSEMBLY 58 P0513X2B058 WHEEL BRUSH

17-1 P0513X2B017-1 BUSHING 59 P0513X2B059 CAP SCREW M6-1 X 25

17-2 P0513X2B017-2 BALL BEARING 6204-2RS 60 P0513X2B060 STAR KNOB

17-3 P0513X2B017-3 INT RETAINING RING 47MM 61 P0513X2B061 LOCK NUT M6-1

17-4 P0513X2B017-4 UPPER WHEEL 17" 62 P0513X2B062 STRAIN RELIEF 16MM STRT LT

17-5 P0513X2B017-5 URETHANE TIRE 17" 1-PAIR 63 P0513X2B063 HEIGHT POINTER

18 P0513X2B018 LOWER WHEEL ASSEMBLY 64 P0513X2B064 HEX NUT M8-1.25

18-1 P0513X2B018-1 BUSHING 65 P0513X2B065 HEX BOLT M8-1.25 X 90

18-2 P0513X2B018-2 BALL BEARING 6204-2RS 66 P0513X2B066 STAR KNOB BOLT M10-1.5 X 20

18-3 P0513X2B018-3 INT RETAINING RING 47MM 67 P0513X2B067 STAR KNOB BOLT M10-1.5 X 53

18-4 P0513X2B018-4 LOWER WHEEL 17" 68 P0513X2B068 THREADED HANDLE M10-1.5

18-5 P0513X2B018-5 URETHANE TIRE, 1-PAIR 69 P0513X2B069 CAM

19 P0513X2B019 MAG SWITCH ASSEMBLY MPE-18 70 P0513X2B070 PILLOW BLOCK

19-1 P0513X2B019-1 MAG SWITCH COVER ASSEMBLY 71 P0513X2B071 HANDLE M12-1.75

19-2 P0513X2B019-2 CONTACTOR SDE MA-18 220V 72 P0513X2B072 LEVER

19-3 P0513X2B019-3 OL RELAY SDE RA-20 8-12A 73 P0513X2B073 HEX NUT M12-1.75

19-5V2 P0513X2B019-5V2 PWR CORD 14G 3W 6-15P V2.02.12 74 P0513X2B074 LEVER HUB

19-6V2 P0513X2B019-6V2 CONTROL CORD 16G 5W V2.05.11 75 P0513X2B075 BUTTON HD CAP SCR M8-1.25 X 20

19-7 P0513X2B019-7 MOTOR CORD 14G 5W 76 P0513X2B076 LOCK WASHER 8MM

19-8 P0513X2B019-8 PHLP HD SCR M5-.8 X 10 78 P0513X2B078 SHAFT COVER

19-9 P0513X2B019-9 RECTIFIER PU-23-2 79 P0513X2B079 SET SCREW M8-1.25 X 20

21 P0513X2B021 WHEEL FLAT WASHER 8MM 80 P0513X2B080 HEX NUT M8-1.25

22 P0513X2B022 CAP SCREW M8-1.25 X 16 81 P0513X2B081 LOWER WHEEL SHAFT

23 P0513X2B023 SAW BLADE 131.5" X 1/2" 6TPI HOOK 82 P0513X2B082 MOTOR 2HP 220V 1-PH W/BRAKE

24 P0513X2B024 LOCK WASHER 8MM 82-2 P0513X2B082-2 MOTOR FAN COVER

25 P0513X2B025 CAP SCREW M8-1.25 X 20 82-3 P0513X2B082-3 MOTOR FAN

28 P0513X2B028 LOWER WHEEL PULLEY 82-4 P0513X2B082-4 CAPACITOR COVER

29 P0513X2B029 HEX NUT 1-14 82-5V2 P0513X2B082-5V2 R CAPACITOR 45M 400V 2 X 2-1/2

30 P0513X2B030 LOCK WASHER 1" 82-6 P0513X2B082-6 MOTOR JUNCTION BOX

31 P0513X2B031 CONTROL PANEL PLATE 82-9 P0513X2B082-9 MAGNETIC BRAKE YZG

32 P0513X2B032 COMPRESSION SPRING 7 X 8 X 90 82-10 P0513X2B082-10 BRAKE SHOE

33 P0513X2B033 ROLL PIN 3 X 16 82-11 P0513X2B082-11 CAP SCREW M6-1 X 12

34 P0513X2B034 ALIGNMENT PLATE 82-12 P0513X2B082-12 LOCK WASHER 6MM

35 P0513X2B035 THRUST BEARING 51201 82-13 P0513X2B082-13 KEY 5 X 5 X 25

36 P0513X2B036 TAP SCREW M4 X 10 82-14 P0513X2B082-14 BALL BEARING 6203ZZ

37 P0513X2B037 TENSION HANDWHEEL 82-15 P0513X2B082-15 BALL BEARING 6205ZZ

38 P0513X2B038 TENSION ADJUSTING ROD 83 P0513X2B083 HEX BOLT M10-1.5 X 25

39 P0513X2B039 FLANGE SCREW M5-.8 X 10 84 P0513X2B084 LOCK WASHER 10MM

40 P0513X2B040 STOP BUTTON 85 P0513X2B085 MOTOR MOUNT BRACKET

G0513 Series Bandsaws -91-

G0513X2B Main Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

86 P0513X2B086 BUTTON HD CAP SCR M8-1.25 X 20 94 P0513X2B094 CAP SCREW M6-1 X 10

87 P0513X2B087 STRAIN RELIEF PLATE 1-HOLE 95 P0513X2B095 LOWER WHEEL COVER

88 P0513X2B088 FLANGE SCREW M5-.8 X 10 97 P0513X2B097 FENDER WASHER 8MM

89 P0513X2B089 PILLOW BLOCK 111 P0513X2B111 CAP SCREW M6-1 X 20

90 P0513X2B090 KEY 5 X 5 X 35 119 P0513X2B119 LOCK WASHER 8MM

91 P0513X2B091 KEY 5 X 5 X 35 176 P0513X2B176 FLANGE SCREW M5-.8 X 10

92 P0513X2B092 MOTOR PULLEY TYPE-A 3.5" 177 P0513X2B177 STRAIN RELIEF 5/16" ELBOW LT

93 P0513X2B093 V-BELT A-42

G0513X2B Labels

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

201 202

203

204

205

216V2

206

207

208

209

210

211

212

213

214

215

REF PART # DESCRIPTION REF PART # DESCRIPTION

201 P0513X2B201 MODEL NUMBER LABEL 209 P0513X2B209 ELECTRICITY LABEL

202 P0513X2B202 GRIZZLY LOGO PLATE 210 P0513X2B210 EXTREME SERIES PLATE

203 P0513X2B203 OPEN DOOR LABEL 211 P0513X2B211 DISCONNECT POWER LABEL

204 P0513X2B204 GUARD ADJ LABEL 212 P0513X2B212 OPEN DOOR LABEL

205 P0513X2B205 SCALE DIRECTIONS LABEL 213 P0513X2B213 PUTTY TOUCH-UP PAINT

206 P0513X2B206 SAFETY GLASSES LABEL 214 P0513X2B214 TENSION ADJ LABEL

207 P0513X2B207 HANDS/BLADE LABEL 215 P0513X2B215 GRIZZLY GREEN TOUCH-UP PAINT

208 P0513X2B208 READ MANUAL LABEL 216V2 P0513X2B216V2 MACHINE ID LABEL CSA V2.05.11

-92- G0513 Series Bandsaws

G0513X2BF Main

38 39

55 55A

111

61 111

79 80 78

171

172

174

175

177

178

173

119

82-2

82-3

82-4

82-5

82-6

82-10

82-9

82-15

82-14

19 19-1

19-2

19-3

19-5

19-4

19-6

17-1

17-2

17-3

17-4

17-5

18-1

18-2

18-3

18-4

18-5

G0513 Series Bandsaws -93-

G0513X2BF Main Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

2 P0513X2BF002 SET SCREW M6-1 X 10 46 P0513X2BF046 UPPER WHEEL SLIDING BRACKET

3 P0513X2BF003 BUSHING 47 P0513X2BF047 CAP SCREW M6-1 X 25

4 P0513X2BF004 LIFTING EYE BOLT M10-1.5 48 P0513X2BF048 STEEL BLIND RIVET 3 X 13MM

5 P0513X2BF005 MACHINE BODY 49 P0513X2BF049 CAP SCREW M6-1 X 10

7 P0513X2BF007 BUSHING 50 P0513X2BF050 CLEAR WINDOW

8 P0513X2BF008 FLAT WASHER 6MM 51 P0513X2BF051 KEY SWITCH

10 P0513X2BF010 HEX NUT M6-1 55A P0513X2BF055A UPPER WHEEL COVER ASSY

11 P0513X2BF011 POINTER 55 P0513X2BF055 UPPER WHEEL COVER

12 P0513X2BF012 STEP SCREW M4-.7 X 5 56 P0513X2BF056 HEX BOLT M6-1 X 25

13 P0513X2BF013 HINGE SHAFT 57 P0513X2BF057 FLAT WASHER 6MM

14 P0513X2BF014 ROLL PIN 5 X 35 58 P0513X2BF058 WHEEL BRUSH

15 P0513X2BF015 UPPER WHEEL SHAFT HINGE 59 P0513X2BF059 CAP SCREW M6-1 X 25

16 P0513X2BF016 UPPER WHEEL SHAFT 60 P0513X2BF060 STAR KNOB

17 P0513X2BF017 UPPER WHEEL ASSEMBLY 61 P0513X2BF061 LOCK NUT M6-1

17-1 P0513X2BF017-1 BUSHING 62 P0513X2BF062 STRAIN RELIEF 16MM STRAIGHT LT

17-2 P0513X2BF017-2 BALL BEARING 6204-2RS 63 P0513X2BF063 HEIGHT POINTER

17-3 P0513X2BF017-3 INT RETAINING RING 47MM 64 P0513X2BF064 HEX NUT M8-1.25

17-4 P0513X2BF017-4 UPPER WHEEL 17" 65 P0513X2BF065 HEX BOLT M8-1.25 X 90

17-5 P0513X2BF017-5 URETHANE TIRE 17" 1-PAIR 66 P0513X2BF066 STAR KNOB BOLT M10-1.5 X 20

18 P0513X2BF018 LOWER WHEEL ASSEMBLY 67 P0513X2BF067 STAR KNOB BOLT M10-1.5 X 53

18-1 P0513X2BF018-1 BUSHING 68 P0513X2BF068 THREADED HANDLE M10-1.5

18-2 P0513X2BF018-2 BALL BEARING 6204-2RS 69 P0513X2BF069 CAM

18-3 P0513X2BF018-3 INT RETAINING RING 47MM 70 P0513X2BF070 PILLOW BLOCK

18-4 P0513X2BF018-4 LOWER WHEEL 17" 71 P0513X2BF071 HANDLE M12-1.75

18-5 P0513X2BF018-5 URETHANE TIRE 17" 1-PAIR 72 P0513X2BF072 LEVER

19 P0513X2BF019 MAG SWITCH ASSY SDE MPE-18 220V 73 P0513X2BF073 HEX NUT M12-1.75

19-1 P0513X2BF019-1 CONTACTOR SDE MA-18 220V 74 P0513X2BF074 LEVER HUB

19-2 P0513X2BF019-2 OL RELAY SDE RA-20 8-12A 75 P0513X2BF075 BUTTON HD CAP SCR M8-1.25 X 20

19-3 P0513X2BF019-3 MAG SWITCH COVER ASSEMBLY 76 P0513X2BF076 LOCK WASHER 8MM

19-4 P0513X2BF019-4 CONTROL CORD 16G 5W V2.05.11 78 P0513X2BF078 SHAFT COVER

19-5 P0513X2BF019-5 MOTOR CORD 14G 5W 79 P0513X2BF079 SET SCREW M8-1.25 X 20

19-6 P0513X2BF019-6 PHLP HD SCR M5-.8 X 10 80 P0513X2BF080 HEX NUT M8-1.25

21 P0513X2BF021 WHEEL FLAT WASHER 8MM 81 P0513X2BF081 LOWER WHEEL SHAFT

22 P0513X2BF022 CAP SCREW M8-1.25 X 16 82 P0513X2BF082 MOTOR 2HP 220V 1-PH W/BRAKE

23 P0513X2BF023 SAW BLADE 131.5" X 1/2" 6TPI HOOK 82-2 P0513X2BF082-2 MOTOR FAN COVER

24 P0513X2BF024 LOCK WASHER 8MM 82-3 P0513X2BF082-3 MOTOR FAN

25 P0513X2BF025 CAP SCREW M8-1.25 X 20 82-4 P0513X2BF082-4 CAPACITOR COVER

28 P0513X2BF028 WHEEL PULLEY/BRAKE DRUM 82-5 P0513X2BF082-5 R CAPACITOR 45M 400V 2 X 2-1/2

29 P0513X2BF029 HEX NUT 1-14 82-6 P0513X2BF082-6 MOTOR JUNCTION BOX

30 P0513X2BF030 LOCK WASHER 1" 82-9 P0513X2BF082-9 MAGNETIC BRAKE YZG

31 P0513X2BF031 CONTROL PANEL PLATE 82-10 P0513X2BF082-10 BRAKE SHOE

32 P0513X2BF032 COMPRESSION SPRING 7 X 8 X 90 82-14 P0513X2BF082-14 BALL BEARING 6205ZZ

33 P0513X2BF033 ROLL PIN 3 X 16 82-15 P0513X2BF082-15 BALL BEARING 6203ZZ

34 P0513X2BF034 ALIGNMENT PLATE 83 P0513X2BF083 HEX BOLT M10-1.5 X 25

35 P0513X2BF035 THRUST BEARING 51201 84 P0513X2BF084 LOCK WASHER 10MM

36 P0513X2BF036 TAP SCREW M4 X 10 85 P0513X2BF085 MOTOR MOUNT BRACKET

37 P0513X2BF037 TENSION HANDWHEEL 86 P0513X2BF086 BUTTON HD CAP SCR M8-1.25 X 20

38 P0513X2BF038 TENSION ADJUSTING ROD 87 P0513X2BF087 STRAIN RELIEF PLATE 1-HOLE

39 P0513X2BF039 FLANGE SCREW M5-.8 X 10 88 P0513X2BF088 TAP SCREW M4 X 10

40 P0513X2BF040 STOP BUTTON 89 P0513X2BF089 PILLOW BLOCK

41 P0513X2BF041 START BUTTON 90 P0513X2BF090 KEY 5 X 5 X 35

44 P0513X2BF044 CAP SCREW M8-1.25 X 16 91 P0513X2BF091 HEX BOLT M8-1.25 X 20 LH

45 P0513X2BF045 FENDER WASHER 8MM 92 P0513X2BF092 MOTOR PULLEY TYPE-A 3.5"

-94- G0513 Series Bandsaws

G0513X2BF Main Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

93 P0513X2BF093 V-BELT A42 172 P0513X2BF172 CORD CLIP 5/16"

94 P0513X2BF094 CAP SCREW M6-1 X 10 173 P0513X2BF173 FLANGE SCREW M5-.8 X 50

95 P0513X2BF095 LOWER WHEEL COVER 174 P0513X2BF174 PHLP HD SCR M4-.7 X 10

97 P0513X2BF097 FENDER WASHER 8MM 175 P0513X2BF175 EXT TOOTH WASHER 5MM

111 P0513X2BF111 CAP SCREW M6-1 X 20 177 P0513X2BF177 JUNCTION BOX

119 P0513X2BF119 LOCK WASHER 8MM 178 P0513X2BF178 WIRE NUT 14-22G

171 P0513X2BF171 FLANGE SCREW M5-.8 X 10

G0513X2BF Labels

201 202

203 204

205

206

207

208

209

213

214

215

216

211

207

209

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

REF PART # DESCRIPTION REF PART # DESCRIPTION

201 P0513X2BF201 MODEL NUMBER LABEL 208 P0513X2BF208 READ MANUAL LABEL

202 P0513X2BF202 NAMEPLATE-LARGE 209 P0513X2BF209 ELECTRICITY LABEL

203 P0513X2BF203 DON'T OPEN DOOR LABEL 211 P0513X2BF211 UNPLUG/DOOR HAZARD LABEL

204 P0513X2BF204 GUARD ADJUSTMENT LABEL 213 P0513X2BF213 PUTTY TOUCH-UP PAINT

205 P0513X2BF205 SCALE DIRECTIONS LABEL 214 P0513X2BF214 TENSION ADJ LABEL

206 P0513X2BF206 SAFETY GLASSES LABEL 215 P0513X2BF215 GRIZZLY GREEN TOUCH-UP PAINT

207 P0513X2BF207 HANDS/BLADE HAZARD LABEL 216 P0513X2BF216 MACHINE ID LABEL

G0513 Series Bandsaws -95-

G0513X2F Main

34 35 37

55A

79 80

111

190

193

194

195

61 111

48 39

93 97

119

17-1

17-2

17-3

17-4

17-5

18-1

18-2

18-3

18-4

18-5

196

197

198

199

200

243

244

(110V)

244-1

244-2

242-5

242-4

244-3

242

(220V)

243

242-1

242-2

242-3

242-5

242-4

188

189

82-1

82-2

82-6

82-5

82-4

82-3

82-7 82-8

82-8A

82-10 82-9

-96- G0513 Series Bandsaws

G0513X2F Main Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

2 P0513X2F002 SET SCREW M6-1 X 10 59 P0513X2F059 CAP SCREW M6-1 X 25

3 P0513X2F003 BUSHING 60 P0513X2F060 STAR KNOB

4 P0513X2F004 LIFTING EYE BOLT M10-1.5 61 P0513X2F061 LOCK NUT M6-1

5 P0513X2F005 MACHINE BODY 62 P0513X2F062 STRAIN RELIEF 16MM STRAIGHT LT

7 P0513X2F007 BUSHING 63 P0513X2F063 HEIGHT POINTER

8 P0513X2F008 FLAT WASHER 6MM 64 P0513X2F064 HEX NUT M8-1.25

10 P0513X2F010 HEX NUT M6-1 65 P0513X2F065 HEX BOLT M8-1.25 X 90

11 P0513X2F011 POINTER 66 P0513X2F066 STAR KNOB BOLT M10-1.5 X 20

12 P0513X2F012 STEP SCREW M4-.7 X 5 67 P0513X2F067 STAR KNOB BOLT M10-1.5 X 55

13 P0513X2F013 HINGE SHAFT 68 P0513X2F068 THREADED HANDLE M10-1.5

14 P0513X2F014 ROLL PIN 5 X 36 69 P0513X2F069 CAM

15 P0513X2F015 UPPER WHEEL SHAFT HINGE 70 P0513X2F070 PILLOW BLOCK

16 P0513X2F016 UPPER WHEEL SHAFT 71 P0513X2F071 HANDLE M12-1.75

17 P0513X2F017 UPPER WHEEL ASSEMBLY 72 P0513X2F072 LEVER

17-1 P0513X2F017-1 BUSHING 73 P0513X2F073 HEX NUT M12-1.75

17-2 P0513X2F017-2 BALL BEARING 6204-2RS 74 P0513X2F074 LEVER HUB

17-3 P0513X2F017-3 INT RETAINING RING 47MM 75 P0513X2F075 BUTTON HD CAP SCR M8-125 X 20

17-4 P0513X2F017-4 UPPER WHEEL 17" 76 P0513X2F076 LOCK WASHER 8MM

17-5 P0513X2F017-5 URETHANE TIRE 17" 1-PAIR 78 P0513X2F078 SHAFT COVER

18 P0513X2F018 LOWER WHEEL ASSEMBLY 79 P0513X2F079 SET SCREW M8-1.25 X 20

18-1 P0513X2F018-1 BUSHING 80 P0513X2F080 HEX NUT M8-1.25

18-2 P0513X2F018-2 BALL BEARING 6204-2RS 81 P0513X2F081 LOWER WHEEL SHAFT

18-3 P0513X2F018-3 INT RETAINING RING 47MM 82 P0513X2F082 MOTOR 2HP 110V/220V 1-PH

18-4 P0513X2F018-4 LOWER WHEEL 17" 82-1 P0513X2F082-1 MOTOR FAN COVER

18-5 P0513X2F018-5 URETHANE TIRE, 1-PAIR 82-2 P0513X2F082-2 MOTOR FAN

21 P0513X2F021 WHEEL FLAT WASHER 8MM 82-3 P0513X2F082-3 CAPACITOR COVER

22 P0513X2F022 CAP SCREW M8-1.25 X 16 82-4 P0513X2F082-4 R CAPACITOR 40M 250V 1-3/8 X 2-5/8

23 P0513X2F023 SAW BLADE 131.5" X 1/2" 6TPI HOOK 82-5 P0513X2F082-5 MOTOR JUNCTION BOX

24 P0513X2F024 LOCK WASHER 8MM 82-6 P0513X2F082-6 S CAPACITOR 300M 250V 1-1/2 X 2-3/8

25 P0513X2F025 CAP SCREW M8-1.25 X 20 82-7 P0513X2F082-7 CONTACT PLATE 5/8

28 P0513X2F028 WHEEL PULLEY/BRAKE DRUM 82-8A P0513X2F082-8A CENTRIFUGAL SWITH W/CONT PLATE

29 P0513X2F029 HEX NUT 1-14 82-8 P0513X2F082-8 CENTRIFUGAL SWITCH 5/8-1725

30 P0513X2F030 LOCK WASHER 1" 82-9 P0513X2F082-9 BALL BEARING 6205ZZ

32 P0513X2F032 COMPRESSION SPRING 7 X 8 X 90 82-10 P0513X2F082-10 BALL BEARING 6203ZZ

33 P0513X2F033 ROLL PIN 3 X 16 83 P0513X2F083 HEX BOLT M10-1.5 X 25

34 P0513X2F034 ALIGNMENT PLATE 84 P0513X2F084 LOCK WASHER 10MM

35 P0513X2F035 THRUST BEARING 51201 85 P0513X2F085 MOTOR MOUNT BRACKET

37 P0513X2F037 TENSION HANDWHEEL 86 P0513X2F086 BUTTON HD CAP SCR M8-125 X 20

38 P0513X2F038 TENSION ADJUSTING ROD 87 P0513X2F087 STRAIN RELIEF PLATE 1-HOLE

39 P0513X2F039 FLANGE SCREW M5-.8 X 10 88 P0513X2F088 FLANGE SCREW M5-.8 X 10

43 P0513X2F043 CONTROL PANEL PLATE 89 P0513X2F089 PILLOW BLOCK

44 P0513X2F044 CAP SCREW M8-1.25 X 16 90 P0513X2F090 KEY 5 X 5 X 35

45 P0513X2F045 FENDER WASHER 8MM 91 P0513X2F091 HEX BOLT M8-1.25 X 20 LH

46 P0513X2F046 UPPER WHEEL SLIDING BRACKET 92 P0513X2F092 MOTOR PULLEY TYPE-A 3.5"

47 P0513X2F047 CAP SCREW M8-1.25 X 50 93 P0513X2F093 V-BELT A42

48 P0513X2F048 STEEL BLIND RIVET 3 X 13MM 94 P0513X2F094 CAP SCREW M6-1 X 10

49 P0513X2F049 CAP SCREW M6-1 X 10 95 P0513X2F095 LOWER WHEEL COVER

50 P0513X2F050 CLEAR WINDOW 97 P0513X2F097 FENDER WASHER 8MM

55A P0513X2F055A UPPER WHEEL COVER ASSY 111 P0513X2F111 CAP SCREW M6-1 X 20

55 P0513X2F055 UPPER WHEEL COVER 119 P0513X2F119 FLAT WASHER 4MM

56 P0513X2F056 HEX BOLT M6-1 X 25 188 P0513X2F188 FLANGE SCREW M5-.8 X 10

57 P0513X2F057 FLAT WASHER 6MM 189 P0513X2F189 CORD CLIP 5/16"

58 P0513X2F058 WHEEL BRUSH 190 P0513X2F190 TAP SCREW M4 X 10

G0513 Series Bandsaws -97-

G0513X2F Main Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

193 P0513X2F193 KEY SWITCH 242-2 P0513X2F242-2 OL RELAY SDE RA-20 8-12A

194 P0513X2F194 START BUTTON 242-3 P0513X2F242-3 MAG SWITCH COVER ASSEMBLY

195 P0513X2F195 STOP BUTTON 242-4 P0513X2F242-4 CONTROL CORD 16G 3W

196 P0513X2F196 FLANGE SCREW M5-.8 X 50 242-5 P0513X2F242-5 MOTOR CORD 14G 3W

197 P0513X2F197 JUNCTION BOX 243 P0513X2F243 PHLP HD SCR M5-.8 X 10

198 P0513X2F198 WIRE NUT 14-22G 244 P0513X2F244 MAG SWITCH ASSY 110V MPE-18

199 P0513X2F199 EXT TOOTH WASHER 5MM 244-1 P0513X2F244-1 CONTACTOR SDE MA-18 110V

200 P0513X2F200 PHLP HD SCR M4-.7 X 10 244-2 P0513X2F244-2 OL RELAY SDE RA-30 18-26A

242 P0513X2F242 MAG SWITCH ASSY 220V MPE-09 244-3 P0513X2F244-3 MAG SWITCH COVER ASSEMBLY

242-1 P0513X2F242-1 CONTACTOR SDE MA-09 220-240V

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

G0513X2F Labels

201 202

203 204

205

206

207

208

209

213

214

215

216

211

203

209

REF PART # DESCRIPTION REF PART # DESCRIPTION

201 P0513X2F201 MODEL NUMBER LABEL 208 P0513X2F208 READ MANUAL LABEL

202 P0513X2F202 GRIZZLY NAMEPLATE- LARGE 209 P0513X2F209 ELECTRICITY LABEL

203 P0513X2F203 DON'T OPEN DOOR LABEL 211 P0513X2F211 UNPLUG/DOOR HAZARD LABEL

204 P0513X2F204 GUARD ADJUSTMENT LABEL 213 P0513X2F213 PUTTY TOUCH-UP PAINT

205 P0513X2F205 SCALE DIRECTIONS LABEL 214 P0513X2F214 TENSION ADJUSTMENT LABEL

206 P0513X2F206 SAFETY GLASSES LABEL 215 P0513X2F215 GRIZZLY GREEN TOUCH-UP PAINT

207 P0513X2F207 HANDS/BLADE HAZARD LABEL 216 P0513X2F216 MACHINE ID LABEL

-98- G0513 Series Bandsaws

G0513X2, G0513X2B, G0513X2BF, &

G0513X2F Guides & Trunnions

142

141

140

138

136 137

150

150-1

150-2

150-4

150-3

150-7

150-8

150-9

150-6

150-10

150-11

150-5

151-5

151-6

151-7

151-8

151-11

151-10 151-9

151

139V2

103

104

155-3

155

155-1

155-10

155-11

155-31

155-12 155-13

155-14

155-15

155-16

155-17

155-18

155-19

155-2

155-2 155-20V2

155-21

155-22

155-23

155-32

155-24

155-25

155-26

155-33

155-27

155-28

155-29

155-3

155-30

155-4

155-5

155-6

155-7

155-8

155-9

354

353

352

145

145-1

145-10

145-11

145-12

145-13

145-14

145-15

145-16

145-17

145-18

145-2

145-3

145-4

145-5

145-6

145-7

145-8

145-9

146

147

355 356

357

G0513 Series Bandsaws -99-

G0513X2, G0513X2B, G0513X2BF, &

G0513X2F Guides & Trunnions Parts List

REF PART # DESCRIPTION REF PART # DESCRIPTION

98 P0513X2098 CAP SCREW M10-1.5 X 35 151-7 P0513X2151-7 ECCENTRIC SHAFT

103 P0513X2103 LOCK WASHER 10MM 151-8 P0513X2151-8 EXT RETAINING RING 15MM

104 P0513X2104 FLAT WASHER 10MM 151-9 P0513X2151-9 BALL BEARING 6202ZZ

136 P0513X2136 CAP SCREW M5-.8 X 10 151-10 P0513X2151-10 HANDLE BUSHING

137 P0513X2137 FLAT WASHER 5MM 151-11 P0513X2151-11 CAP SCREW M6-1 X 35

138 P0513X2138 UPPER BLADE GUARD 155 P0513X2155 CAST IRON TRUNNION ASSEMBLY

139V2 P0513X2139V2 CAP SCREW M10-1.5 X 35 155-1 P0513X2155-1 FLAT WASHER 8MM

140 P0513X2140 STEP SCREW M4-.7 X 5 155-2 P0513X2155-2 LOCK NUT M8-1.25

141 P0513X2141 FIBER WASHER 5MM 155-3 P0513X2155-3 PHLP HD SCR M4-.7 x 6

142 P0513X2142 SLIDING PLATE 155-4 P0513X2155-4 GEAR PLATE

145 P0513X2145 GUIDE POST ASSEMBLY 155-5 P0513X2155-5 FLAT HD SCR M4-.7 X 6

145-1 P0513X2145-1 SET SCREW M5-.8 X 5 155-6 P0513X2155-6 CARRIAGE BOLT M8-1.25 X 85

145-2 P0513X2145-2 CAP SCREW M6-1 X 16 155-7 P0513X2155-7 CAST IRON TRUNNION

145-3 P0513X2145-3 PHLP HD SCR M4-.7 X 10 155-8 P0513X2155-8 CARRIAGE BOLT M8-1.25 X 80

145-4 P0513X2145-4 HEX NUT M4-.7 155-9 P0513X2155-9 LOCK HANDLE M8-1.25

145-5 P0513X2145-5 RACK 155-10 P0513X2155-10 TABLE TILT SCALE

145-6 P0513X2145-6 GUIDE POST 155-11 P0513X2155-11 FLAT WASHER 8MM

145-7 P0513X2145-7 LOCK COLLAR 155-12 P0513X2155-12 HEX BOLT M8-1.25 X 25

145-8 P0513X2145-8 THREADED BUSHING V2.06.09 155-13 P0513X2155-13 LOCK HANDLE M8-1.25

145-9 P0513X2145-9 LOCK WASHER 8MM 155-14 P0513X2155-14 FLAT WASHER 4MM

145-10 P0513X2145-10 THREADED GUIDE BRACKET 14MM V2.06.09 155-15 P0513X2155-15 POINTER

145-11 P0513X2145-11 WORM CYLINDER 155-16 P0513X2155-16 LOCK WASHER 8MM

145-12 P0513X2145-12 FIXED PLATE 155-17 P0513X2155-17 ADJUSTMENT KNOB BOLT M6-1

145-13 P0513X2145-13 PINION GEAR 15T 155-18 P0513X2155-18 HEX NUT M6-1

145-14 P0513X2145-14 PINION GEAR STEP BOLT 155-19 P0513X2155-19 L-BRACKET

145-15 P0513X2145-15 BRACKET COVER 155-20V2 P0513X2155-20V2 FLAT HD SCR M5-.8 X 8

145-16 P0513X2145-16 CAP SCREW M8-1.25 X 16 155-21 P0513X2155-21 CAP SCREW M6-1 X 16

145-17 P0513X2145-17 FLAT HD SCR M4-.7 X 8 155-22 P0513X2155-22 CAP SCREW M6-1 X 50

145-18 P0513X2145-18 BUSHING 155-23 P0513X2155-23 TRUNNION SUPPORT BRACKET

146 P0513X2146 GUIDE POST HANDWHEEL 155-24 P0513X2155-24 TRUNNION GEAR

147 P0513X2147 CAP SCREW M6-1 X 20 155-25 P0513X2155-25 BUTTON HD CAP SCR M10-1.5 X 30

150 P0513X2150 UPPER BLADE GUIDE ASSEMBLY 155-26 P0513X2155-26 RIGHT GUARD

150-1 P0513X2150-1 CAP SCREW M6-1 X 16 155-27 P0513X2155-27 BALL BEARING 6000ZZ

150-2 P0513X2150-2 UPPER GUIDE SUPPORT BLOCK 155-28 P0513X2155-28 FLAT WASHER 10MM

150-3 P0513X2150-3 SET SCREW M6-1 X 10 155-29 P0513X2155-29 LEFT GUARD

150-4 P0513X2150-4 ADJUSTMENT BAR 155-30 P0513X2155-30 ADJUSTMENT ROD

150-5 P0513X2150-5 UPPER BLADE GUIDE SUPPORT 155-31 P0513X2155-31 LOCK WASHER 8MM

150-6 P0513X2150-6 ECCENTRIC SHAFT 155-32 P0513X2155-32 CAP SCREW M5-.8 X 6

150-7 P0513X2150-7 EXT RETAINING RING 15MM 155-33 P0513X2155-33 LOCK WASHER 10MM

150-8 P0513X2150-8 BALL BEARING 6202ZZ 352 P0513X2352 FLAT WASHER 8MM

150-9 P0513X2150-9 HANDLE BUSHING 353 P0513X2353 LOCK WASHER 8MM

150-10 P0513X2150-10 CAP SCREW M6-1 X 35 354 P0513X2354 BUTTON HD CAP SCR M8-1.25 X 20

150-11 P0513X2150-11 UPPER SPACING SHAFT 355 P0513X2355 HEX WRENCH 5MM

151 P0513X2151 LOWER BLADE GUIDE ASSEMBLY 356 P0513X2356 HEX WRENCH 8MM

151-5 P0513X2151-5 LOWER BLADE GUIDE SUPPORT 357 P0513X2357 WRENCH 10 X 13 OPEN-END

151-6 P0513X2151-6 CAP SCREW M6-1 X 16

-100- G0513 Series Bandsaws

G0513X2 & G0513X2F Fence Assembly &

Table

121-20

121-17

121-21

121-1

121-19

121-24

121-14

121-7

121-29

121-25

121-23

121-2 121-13

121-15

121-11 121-16

121

121-27

121-9

121-26

121-3

121-18

126 127

128

121-10

121-22

121-8

121-6

121-5

121-4

121-12

350

350-1

350-2

350-4 350-3

152

REF PART # DESCRIPTION REF PART # DESCRIPTION

121 P0513X2121 FENCE ASSEMBLY 121-19 P0513X2121-19 PLUG

121-1 P0513X2121-1 FRONT RAIL 640MM 121-20 P0513X2121-20 TAP SCREW M3.5 X 8

121-2 P0513X2121-2 ADJUST BASE 121-21 P0513X2121-21 FENCE SCALE 18-1/2"

121-3 P0513X2121-3 FIXED SHAFT 121-22 P0513X2121-22 HEX NUT M6-1

121-4 P0513X2121-4 SHAFT 121-23 P0513X2121-23 LOCK WASHER 6MM

121-5 P0513X2121-5 SPRING PIECE 121-24 P0513X2121-24 CAP SCREW M6-1 X 16

121-6 P0513X2121-6 LOCK KNOB M8-1.25 X 44 121-25 P0513X2121-25 HEX BOLT M6-1 X 20

121-7 P0513X2121-7 CAST IRON FENCE 590MM 121-26 P0513X2121-26 FLANGE BOLT M4-.7 X 8

121-8 P0513X2121-8 FLAT WASHER 8MM 121-27 P0513X2121-27 FLAT WASHER 6MM

121-9 P0513X2121-9 FENCE HANDLE M8-1.25 X 22 121-29 P0513X2121-29 SPACER PLATE

121-10 P0513X2121-10 RAIL PAD 126 P0513X2126 TABLE 17" X 24"

121-11 P0513X2121-11 CONVEX WINDOW 127 P0513X2127 TABLE INSERT

121-12 P0513X2121-12 CAP SCREW M6-1 X 24 128 P0513X2128 TABLE PIN

121-13 P0513X2121-13 LOCK BLOCK 152 P0513X2152 MITER GAUGE ASSY

121-14 P0513X2121-14 REAR RAIL 640MM 350 P0513X2350 RESAW FENCE ASSEMBLY

121-15 P0513X2121-15 HEX NUT M8-1.25 350-1 P0513X2350-1 ALUMINUM RESAW FENCE 590MM

121-16 P0513X2121-16 FLANGE SCREW M4-.7 X 6 350-2 P0513X2350-2 TAP SCREW 3.5 X 8

121-17 P0513X2121-17 GUARD PIECE 350-3 P0513X2350-2 FENCE END PLATE 148 X 22 X 1

121-18 P0513X2121-18 MOVING PLATE 350-4 P0513X2350-2 RESAW FENCE SCALE

G0513 Series Bandsaws -101-

G0513X2B & G0513X2BF Fence Assembly &

Table

157

157-1

157-12

157-10

157-11

157-14V2

157-15

157-16

157-17V2

157-18

157-13

157-2

157-3V2

157-4

157-5

157-6

157-7

157-8

157-9

163

165V2

164

162

161

161-1

160

158

159

153

154

126

127

128

152

156

156-1

156-2

156-4 156-3

REF PART # DESCRIPTION REF PART # DESCRIPTION

126 P0513X2B126 TABLE 17" X 24" 157-9 P0513X2B157-9 SHAFT

127 P0513X2B127 TABLE INSERT 157-10 P0513X2B157-10 PLASTIC SET SCREW M7-1 X 10

128 P0513X2B128 TABLE PIN 157-11 P0513X2B157-11 NYLON PAD

152 P0513X2B152 MITER GAUGE ASSY 157-12 P0513X2B157-12 SET SCREW M8-1.25 X 12

153 P0513X2B153 KNOB SCREW M8-1.25 X 20 157-13 P0513X2B157-13 HEX NUT M8-1.25

154 P0513X2B154 OUTER RAIL PLATE 157-14V2 P0513X2B157-14V2 HEX BOLT M8-1.25 X 20

156 P0513X2B156 RESAW FENCE ASSEMBLY 157-15 P0513X2B157-15 HEX NUT M8-1.25

156-1 P0513X2B156-1 ALUMINUM RESAW FENCE 590MM 157-16 P0513X2B157-16 FLAT WASHER 8MM

156-2 P0513X2B156-2 TAP SCREW 3.5 X 8 157-17V2 P0513X2B157-17V2 LOCK HANDLE M8-1.25 X 45 V2.05.11

156-3 P0513X2B156-3 FENCE END PLATE 148 X 22 X 1 157-18 P0513X2B157-18 MOVING PLATE

156-4 P0513X2B156-4 RESAW FENCE SCALE 158 P0513X2B158 FLAT WASHER 8MM

157 P0513X2B157 FENCE ASSEMBLY 159 P0513X2B159 LOCK WASHER 8MM

157-1 P0513X2B157-1 FENCE 160 P0513X2B160 CAP SCREW M8-1.25 X 20

157-2 P0513X2B157-2 POINTER 161 P0513X2B161 FRONT RAIL

157-3V2 P0513X2B157-3V2 SET SCREW M8-1.25 X 25 161-1 P0513X2B161-1 FENCE SCALE

157-4 P0513X2B157-4 SPRING PIECE 162 P0513X2B162 INNER RAIL PLATE

157-5 P0513X2B157-5 FLANGE SCREW M4-.7 X 8 163 P0513X2B163 FLAT WASHER 6MM

157-6 P0513X2B157-6 PIVOT BLOCK 164 P0513X2B164 LOCK WASHER 6MM

157-7 P0513X2B157-7 HEX NUT M8-1.25 165V2 P0513X2B165V2 CAP SCREW M6-1 X 20

157-8 P0513X2B157-8 FENCE LOCK HANDLE

-102- G0513 Series Bandsaws

G0513X2BF & G0513X2F Foot Brake

305

304

303

302

301

308

307

306

325

326

324

323

317

321

318

320

319

314

316

315

313

312

311

310309

317

322

317

REF PART # DESCRIPTION REF PART # DESCRIPTION

301 P0513X2F301 CONDUIT GROMMET 314 P0513X2F314 LOCK WASHER 6MM

302 P0513X2F302 FLEXIBLE CONDUIT 1/2" X 42" 315 P0513X2F315 BRAKE SHOE

303 P0513X2F303 SWITCH CORD 16G 2W 316 P0513X2F316 BUSHING

304 P0513X2F304 HEX NUT 4MM 317 P0513X2F317 CAP SCREW M6-1 X 16

305 P0513X2F305 BRAKE SWITCH SHINOZAKI AZ7141 318 P0513X2F318 HEX NUT M6-1

306 P0513X2F306 PHLP HD SCR M4-.7 X 30 319 P0513X2F319 LOCK WASHER 6MM

307 P0513X2F307 CORD CLIP 5/8" 320 P0513X2F320 BRAKE PEDDLE

308 P0513X2F308 TAP SCREW M4 X 8 321 P0513X2F321 NYLON PAD

309 P0513X2F309 BUSHING 322 P0513X2F322 BRAKE EXTENSION SPRING

310 P0513X2F310 FLAT WASHER 8MM 323 P0513X2F323 HEX NUT M6-1

311 P0513X2F311 LOCK WASHER 8MM 324 P0513X2F324 STEP BOLT M7-1 X 10 W/BUSHING

312 P0513X2F312 CAP SCREW M8-1.25 X 25 325 P0513X2F325 BRAKE LEVER

313 P0513X2F313 CAP SCREW M6-1 X 25 326 P0513X2F326 RUBBER CLIP

CUT ALONG DOTTED LINE

Name _____________________________________________________________________________

Street _____________________________________________________________________________

City _______________________ State _________________________ Zip _____________________

Phone # ____________________ Email _________________________________________________

Model # ____________________ Order # _______________________ Serial # __________________

WARRANTY CARD

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop

better products and services. Of course, all information is strictly confidential.

1. How did you learn about us?

____ Advertisement ____ Friend ____ Catalog

____ Card Deck ____ Website ____ Other:

2. Which of the following magazines do you subscribe to?

3. What is your annual household income?

____ $20,000-$29,000 ____ $30,000-$39,000 ____ $40,000-$49,000

____ $50,000-$59,000 ____ $60,000-$69,000 ____ $70,000+

4. What is your age group?

____ 20-29 ____ 30-39 ____ 40-49

____ 50-59 ____ 60-69 ____ 70+

5. How long have you been a woodworker/metalworker?

____ 0-2 Years ____ 2-8 Years ____ 8-20 Years ____ 20+ Years

6. How many of your machines or tools are Grizzly?

____ 0-2 ____ 3-5 ____ 6-9 ____ 10+

7. Do you think your machine represents a good value? _____Yes _____No

8. Would you recommend Grizzly Industrial to a friend? _____Yes _____No

9. Would you allow us to use your name as a reference for Grizzly customers in your area?

Note: We never use names more than 3 times. _____Yes _____No

10. Comments: _____________________________________________________________________

_________________________________________________________________________________

____ Cabinetmaker & FDM

____ Family Handyman

____ Hand Loader

____ Handy

____ Home Shop Machinist

____ Journal of Light Cont.

____ Live Steam

____ Model Airplane News

____ Old House Journal

____ Popular Mechanics

____ Popular Science

____ Popular Woodworking

____ Precision Shooter

____ Projects in Metal

____ RC Modeler

____ Rie

____ Shop Notes

____ Shotgun News

____ Today’s Homeowner

____ Wood

____ Wooden Boat

____ Woodshop News

____ Woodsmith

____ Woodwork

____ Woodworker West

____ Woodworker’s Journal

____ Other:

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

FOLD ALONG DOTTED LINE

GRIZZLY INDUSTRIAL, INC.

P.O. BOX 2069

BELLINGHAM, WA 98227-2069

Place

Stamp

Here

Name_______________________________

Street_______________________________

City______________State______Zip______

Send a Grizzly Catalog to a friend:

WARRANTY & RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from

the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty

and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-

ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent

that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and

any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,

or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue

you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We

will not accept any item back without this number. Proof of purchase must accompany the merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to

achieve better quality equipment. We make every effort to ensure that our products meet high quality and

durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

G0513X2B G0513x2f M

G0513X2 g0513x2_m

G0513P g0513p_m

Navigation menu

Versions of this User Manual:

Views

Navigation