NRF51822_422_DK User Guide N RF51822 Developer Kit V1.2

• 1 Introduction
  • 1.1 Minimum requirements
  • 1.2 External resources
  • 1.3 Writing conventions
  • 1.4 Development Kit release notes
• 2 Kit content
  • 2.1 nRF51822 Development Kit hardware content
  • 2.2 Downloadable content
    • 2.2.1 nRF51822 DK software content
    • 2.2.2 nRF51822 DK documentation
    • 2.2.3 Schematics, Bill of Materials, PCB layout files, and production files
• 3 Quick start
  • 3.1 Install the nRF51822 connector module
  • 3.2 Bluetooth low energy heart rate monitor demo
• 4 Development kit configuration
  • 4.1 Development environment
    • 4.1.1 Development environment setup
  • 4.2 Kit setup
    • 4.2.1 nRFgo nRF51822 DK modules
    • 4.2.2 nRF51822 Development Dongle (PCA10000)
    • 4.2.3 J-Link Lite CortexM-9 JTAG/SWD Emulator
• 5 Hardware description
  • 5.1 nRFgo nRF51822 DK modules
    • 5.1.1 Key features
    • 5.1.2 Hardware pictures
    • 5.1.3 Block diagram
    • 5.1.4 nRFgo nRF51822 DK module extension
    • 5.1.5 Analog inputs
    • 5.1.6 SWD interface
    • 5.1.7 32.768 kHz crystal
    • 5.1.8 Current measurements
  • 5.2 nRF51822 Development Dongle(PCA10000)
    • 5.2.1 Key features
    • 5.2.2 Hardware pictures
    • 5.2.3 Block diagram
    • 5.2.4 Mulitcolor LED
    • 5.2.5 UART configuration
• 6 Flash programming and application development
  • 6.1 Programming and erasing flash using nRFgo Studio
    • 6.1.1 Selecting a board to program
    • 6.1.2 Identifying the nRF51 chip and chip content
    • 6.1.3 Erase all
    • 6.1.4 Programming a SoftDevice
    • 6.1.5 Programming an application
  • 6.2 Application development
    • 6.2.1 Configuring memory layout
    • 6.2.2 Shared call stack
    • 6.2.3 Debugger configuration
    • 6.2.4 Limitation when debugging on a chip with a SoftDevice
    • 6.2.5 Programming the device
    • 6.2.6 Erasing the device
• 7 Debugging the nRF51822
  • 7.1 nRF51822 debug features and precautions
    • 7.1.1 System Viewer windows
    • 7.1.2 Debugging an application when a readback protected SoftDevice is present
• 8 Testing the physical layer with Direct Test Mode
  • 8.1 Kit setup for UART
  • 8.2 Programming the nRF51822 module with DTM
  • 8.3 DTM testing using nRFgo Studio
• 9 Software Development Kit
  • 9.1 Installing the nRF51 SDK
• 10 Troubleshooting
• Appendix A : Installing drivers and configuring KEIL projects for the SEGGER debugger
  • Prerequisite
  • Download and install SEGGER drivers
  • Configuring KEIL projects for SEGGER debugger for first time use
  • JLinkSettings.ini file