1272 99 06 1500 6inch Lift Kit Rsc_1272 Rsc
User Manual: Pdf rsc_1272
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
92127200 99-06 CHEVY/GM 1500 6” LIFT KIT Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these instructions, professional knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle. Please read all the instructions before beginning the installation. Check the kit hardware against the Kit Contents list on next page. Be sure you have all the needed parts and understand where they go. Also please review the tools needed list to be certain that you have the tools necessary to complete the installation. PRODUCT USE INFORMATION As a general rule, the taller a vehicle is the easier it will roll. We strongly recommend, because of rollover possibility, that seat belts and shoulder harnesses should be worn at all times. Avoid situations where a side rollover may occur. Braking performance and capabilities are decreased when significantly larger/heavier tires and wheels are used. Take this into consideration while driving. Also, speedometer recalibration is necessary when larger tires are installed. Do no add, alter, or fabricate any factory or after-market parts which increase vehicle height over the intended height of the Rough Country product purchased. Mixing component brands, lifts, with this suspension lifts voids all warranties. Rough Country makes no claims regarding lifting devices and excludes any and all implied claims. We will not be responsible for any product that is altered. Due to differences in manufacturing, dimension and inflated measurements, tire and wheel combinations should be test fit prior to installation. For this application we recommend a wheel not to exceed 9” in width with 4.5 “ of backspacing.. Additionally a quality tire of radial design is recommended, not exceeding 35” tall and 12.5” wide. If this vehicle was equipped from the factory with 17” wheels and if purchasing new wheels, the wheel size must not be below 17” but can be larger than 17” due to the vehicle being equipped with larger calipers /rotor. NOTICE TO DEALER AND VEHICLE OWNER Any vehicle equipped with any Rough country product must have the “Warning to Driver” decal installed on the sun visor or dash. The decal is to act as a constant reminder for whoever is operating the vehicle of its unique handling characteristics. INSTALLING DEALER—It is your responsibility to install the warning decal and to forward these installation instructions on too the vehicle owner for review and to be kept in the vehicle for its service life. We hope installing your Rough Country lift kit is a positive experience. Please note that variations in construction and assembly in the vehicle manufacturing process will virtually ensure that some parts may seem difficult to install. Additionally, the current trend in manufacturing of vehicles results in a frame that is highly flexible and may shift slightly on disassembly prior to installation. The use of pry bars and tapered punches for alignment is considered normal and usually does not indicate a faulty product. However, if you are uncertain about some aspect of the installation process, please feel free to call our tech support department at 800-222-7023. We do not recommend that you modify the Rough Country parts in any way as this will void any warranty expressed or implied. Thank you for choosing Rough Country for all of your suspension needs. KIT CONTENTS Rear Blocks (2) Rear U-bolts (4) Torsion Bar Bracket (2) Pass Bump Stop Bracket Dr Bump Stop Bracket Rear Shocks (2) Sway Bar Link (2) Rear Cross Member Front Shocks (2) Front Cross Member Pass Side Knuckle Dr. Diff Brkt Driver Side Knuckle Pass Diff Brkt CV Spacer (2) Skid Plate Kit Contents: 1272 Box1 Rear Cross Member Dr Torsion Drop Bracket Pass Torsion Drop Bracket Dr Bump Stop Bracket Pass Bump Stop Bracket 1272 Box2 Frt Skid Plate Frt Cross Member Dr Diff Bracket Pass Diff Bracket 1272 Box3 Front Shock Part #658441 (2) Rr Shock Part # 658556 (2) CV Shaft Spacers (2) Lift Blocks (2) 9/16” X 2 1/2” X 12 1/2” U-bolts (4) Front Sway Bar Links (2) 1285 Driver Side Knuckle Pass Side Knuckle Fastener Breakdown: For Driver Side Dif Drop Brkt. Poly Bushings (2) 2.41” x 9/16”ID Sleeve (1) For Bump Stop Bracket 1/2” x 1 1/2” Bolt (2) 1/2” Washer (2) 1/2” Nut (2) For Rear Cross Member 5/8” x 5 1/2” Bolt (2) 5/8” Washer (4) 5/8” Nut (2) For Pass Side Dif Drop Brkt 1/2” x 1 1/2” Bolt (2) 1/2” Washer (4) 1/2” Nut (2) For Front Cross Member 5/8” x 4 1/2” Bolt (2) 5/8” Washer (4) 5/8” Nut (2) For Skid Plate 3/8” x 1” Self Taping Bolt (2) 1/2” x 4 1/2” bolt (1) 1/2” Washer (2) 1/2” Nut (1) For Axle CV Spacers 10mm x 65mm Allen Bolt (12) For Torsion Bar Drop Brackets 1/2” x 1 1/2” Bolts (8) 1/2” Lock Nuts (8) Bushings (4) Sleeves (2) For Front Shock Absorbers Stem Bushings Female(2) Stem Bushings Male (2) Stem Washer (4) 3/8” Nut (2) For Rear U-Bolts 9/16” Washer (8) 9/16” Nut (8) 7/16” Washer (8) 7/16” Nut (8) For Rear Shock Absorbers Hourglass Bushing (4) Shock Sleeve (4) TOOLS NEEDED: Floor Jack Jack Stands 10mm socket /wrench 11mm socket /wrench 13mm Deep Socket 13mm wrench 15mm socket / wrench 17mm socket / wrench 18mm socket /wrench 19mm socket /wrench 21mm socket /wrench 24mm socket /wrench 35mm socket 9/16 socket /wrench 7/8” deep well socket Torsion bar Tool Drill 17/32 Drill Bit Loc-Tite Reciprocating Saw TORQUE SPECS: Size 5/16” 3/8” 7/16” 1/2” 9/16” 5/8” 6MM 8MM 10MM 12MM 14MM 16MM 18MM Grade 5 15 ft/lbs 30 ft/lbs 45 ft/lbs 65 ft/lbs 95 ft/lbs 135 ft/lbs Class 8.8 5 ft/lbs 18ft/lbs 32ft/lbs 55ft/lbs 85ft/lbs 130ft/lbs 170ft/lbs Grade 8 20 ft/lbs 35 ft/lbs 60 ft/lbs 90 ft/lbs 130 ft/lbs 175 ft/lbs Class 10.9 9 ft/lbs 23 ft/lbs 45ft/lbs 75ft/lbs 120ft/lbs 165ft/lbs 240ft/lbs CAD DRAWING SHOWING KIT COMPONENTS AND INSTALLED LOCATIONS DRAWING SHOWN WITH OPTIONAL KICKER BRACES DRAWING SHOWN WITH OPTIONAL KICKER BRACES FRONT INSTALLATION 1. Place the truck on a clean level surface and set the parking brake. Chock the rear wheels. Using a floor jack raise the front of the truck and support the frame rails with jack stands. Never work under an unsupported vehicle. Using a 7/8” deep well socket remove the front wheels. 2. Locate the torsion bar adjuster bolt on the bottom of the rear cross member, measure the threads showing on the torsion bar adjuster bolt. Mark the position of the torsion bars on the control arm and torsion bar key. Mark both the drivers side and passenger side. See Photo 1. 3. Using a torsion bar tool, relieve the pressure from the torsion bar adjuster bolt and remove the bolt and threaded block. See Photo 2.Warning: Be extremely careful when loading and unloading the torsion bars; there is a tremendous amount of stored energy in the bars. Keep you hands and body clear of the adjuster arm assembly and the puller tool in case anything slips or breaks. Photo 1 Mark torsion bar and torsion bar keys Photo 2 Remove torsion bar keys 4. Using a 15 mm socket remove the factory lower skid plate. See Photo 3. 5. Starting on the drivers side use a 10mm socket to remove the brake line from the upper control arm and knuckle. Unplug the ABS wire from the frame rail. See Photo 4. Photo 3 Photo 4 Remove the brake line from the upper arm Remove the skid plate 6. Using a 18mm socket unbolt the brake caliper and rotor. Secure the brake caliper out of harms way. See Photo 5. 7. Using a 35 mm socket remove the CV nut from the knuckle. See Photo 6. Remove the tie rod from the stock knuckle using a 18mm wrench. Strike the side of the knuckle where the tie rod mounts to dislodge the tapered tie rod end. Retain the stock hardware for reuse. Photo 5 Remove the brake caliper bracket Photo 6 Remove the spindle nut 8. Using a 18mm wrench for the upper ball joint and a 24 mm deep well socket for the lower, remove the ball joint nuts. Using a hammer hit the knuckle as shown until the ball joint is free. See Photo 7 & 8. Remove the knuckle. Photo 7 Remove the skid plate Photo 8 Remove the knuckle from the lower ball joint 9. Remove the three factory bolts that hold the wheel bearing to the stock knuckle. Remove the wheel bearing and dust cover using a 15mm socket. Locate the new knuckles supplied with the kit and using Loc-Tite; install the bearing with the factory hardware on the new knuckle. Tighten to 133 ft.lbs. See Photo 9. 10. Using a 13mm deep well socket remove the sway bar link from the lower control arm and sway bar. See Photo 10. Photo 9 Install the bearing in the new knuckle Photo 10 Remove the sway bar link from the lower arm 11. Using a 15 mm wrench remove the upper shock nut. Using a 21 mm socket and 21 mm wrench remove the lower shock bolt. Remove the shock. Retain the hardware for reuse. 12. Using a 15mm socket remove the 6 inner CV bolts. See Photo 11. Set CV half shaft aside for reuse. 13. Using a 18mm wrench and a 24 mm socket remove the lower control arm hardware and remove the lower control arm. Retain the hardware for reuse. Repeat steps 5 through 13 on passenger side. 14. Support the differential with a floor jack and remove the two nuts on the passenger side that secures the differential to the frame using a 21mm wrench. Remove the upper differential bolt that secures the driver side differential to the frame using a 21mm wrench. 15. Mark the front driveshaft and yoke for reference and remove the front driveshaft from the differential using a 11mm wrench. Secure driveshaft out of harms way. See Photo 12. Photo 11 Remove the shaft from the differential Photo 12 Remove the drive shaft from the differential 16. Remove the lower differential bolt on the drivers side using a 21mm wrench. Jack up the differential to allow for the trimming of the drivers side stock mount. 17. Cut the frame as shown in Photo 13 with a reciprocating saw. After trimming, Remove the differential vent hose, differential plug and the plug clips from the axle. With assistance lower the differential down and remove from the vehicle. 18. Cut the differential as shown in Photo 14 using a reciprocating saw. Take care not to damage the differential. Photo 13 Photo 14 Cut Along Line Removing Completely Cut differential mount Cut stock rear diff bracket 19. Locate the driver differential bracket and install the bushings /sleeve in the mount. Install on the differential as shown with factory hardware using a 15mm socket. Tighten to 35ft. Lbs. See Photo 15. 20. Install the bump stop bracket on the lower control arm. Note: There is a driver and passenger side bracket. Photo 15 Install the new diff mount Photo 16 Install the bump stop bracket ( Dr Shown) 21. Install the bump-stop bracket on the lower control arm. Note: There is a driver and passenger side bracket 22. Using the bump-top as a guide, mark the lower control arm as shown and remove the bracket from the arm. See Photo 17. Driver Side shown. A template is included it is recommended to use the template to check that the hole is centered in the mount. Failure to confirm the proper location of the hole may lead to interference of the shock absorber by the bump-stop bracket. 23. Drill the lower control arms using a 17/32” drill bit and reinstall the bump-stop bracket on the lower control arm and tighten the supplied 1/2” x 1 1/2” bolts, washers & nuts using a 3/4” wrench See Photo 18. Photo 17 Mark the hole to be drilled Photo 18 Install the supplied hardware 24. Install the rear cross-member as shown in Photo 19 with supplied 5/8” X 5 1/2” bolts, washers and nuts. Install the bolts from the front to the back. Do not tighten at this time. If the optional kicker braces were purchased with this kit, install the mouting brackets on the rear cross member using the instructions included with that kit. 25. Install the passenger side differential bracket as shown in Photo 20 (tall end of taper positioned towards front of vehicle) with the factory hardware using a 21mm wrench. Do not tighten at this time. Photo1919 Photo Photo 20 Install the rear cross-member Install the Pass side bracket 26. With assistance raise the differential into place and install the rear mount of the differential into the new crossmember mount with the stock hardware. See Photo 21. Do not tighten at this time. NOTE: It will be necessary to trim the cooling fins on the side of the differential to allow for clearance on the frame. Trial fit the differential in the lower mount and trim the cooling fins as needed using a hand grinder. See Photo 22. Photo 21 Install the differential in the cross-member Photo 22 Mark and trim the cooling fins as needed 27. Reinstall the passenger side of the differential into the new mounts with the supplied 1/2” x 1 1/2” bolts, washers & nuts. Do not tighten at this time. Reinstall the driveshaft using marking made as a reference and secure using factory hardware and tighten using a 11mm wrench. Tighten to 19 ft. lbs. 28. Install the front cross-member as shown in Photo 23 with the supplied 5/8” x 4 1/2” bolts, washers & nuts. Do not tighten at this time. Photo 23 Install the front cross-member 29. Install the differential bracket in the mounting tab on the back side of the front cross member and install the skid plate as shown using the supplied 1/2” x 4 1/2” bolt, washers and nut. Install the rear of the skid plate by lining up the holes in the cross-member and installing the supplied 3/8” self tapping bolts and tighten using a 9/16” wrench. See Photo 24 & 25. Do not tighten hardware at this time. Pull the differential vent hose that was previously disconnected down to install in the stock location and reinstall differential plug and wiring clips to the differential. Photo24 23 Photo Install the skid plate with supplied hardware Photo 25 Secure skid plate to rear cross-member 30. Install the lower control arms with the bump stop brackets attached in the new drop brackets with the factory hardware (bolts install front to rear). Do not tighten control arm hardware at this time. 31. Tighten cross-member and differential drop bracket hardware at this time. Tighten 5/8” cross member hardware to 154 ft. lbs., 9/16” differential hardware to 114 ft. lbs., factory hardware on passenger differential bracket to 75ft-lbs. 32. Install the new knuckles with the stock ball joint hardware and tighten using a18mm & 24mm wrench. 33. Install the brake caliper with factory hardware. Using a 10mm wrench install the brake line on the knuckle. See Photo 26. Tighten upper ball joint to 37 ft. lbs and lower to 94 ft. lbs. and tighten brake hardware. Reconnect the ABS wire. If more slack is needed the line can be sprayed with 10-40 and the mounts slid down. 34. Install the stock shafts in the knuckle with factory hardware and using a 35mm socket. Locate the supplied CV spacers and place the spacer in between the differential and the shaft as shown in Photo 27. Using Loc-Tite, secure with the supplied 10mm x 65mm Socket head cap bolts with 8mm allen wrench. Tighten hardware to 58 ft.-lbs. 35. Install the tie rod end in the knuckle with the stock hardware and using a 19mm wrench. Tighten to 50 ft.-lbs. Photo 26 Install brake line to knuckle Photo 27 Install shaft spacers with supplied hardware 36. Install the supplied sway bar links as shown in Photo 28 using a 17mm wrench for the upper and 19mm for the lower mount. Swivel end of link install in lower control arm. Tighten until bushings swell slightly. 37. Remove the stock torsion bar cross-member using a 21mm socket. See Photo 29. Photo 28 Photo 29 Remove the torsion bar cross-member Install sway bar link 38. To ease installation, install the factory torsion bars in the lower control arms and slide forward slightly. Locate new torsion bar drop bracket over the factory rivets on the side of the frame rail and clamp in place. Using the bracket as a guide, mark hole. Remove the bracket and drill holes using a 17/32” drill bit. See Photo 30. 39. Install the supplied bushings /sleeves in the bracket and install the torsion bar cross-member drop bracket with the supplied 1/2” x 1 1/2” bolts & nuts. (4 bolts per side). Do not tighten at this time. See Photo 31. Photo 30 Photo 31 Install torsion bar cross-member brackets Drill the frame rail 40. Install the stock cross-member as shown in Photo 32 with factory hardware and using a 21mm wrench. Tighten cross-member hardware using a 3/4” wrench. 41. Slide the torsion bars back into the cross-member with the stock torsion bar adjusters. Match mark made earlier to properly clock the torsion bar adjuster and the torsion bar. 42. Using a torsion bar tool, load the torsion bars using the mark made earlier as a reference. 43. Locate the supplied front shock absorbers and assemble with bushings/sleeves. Install front shock part #658441 in the factory lower location as shown in Photo 33 with factory hardware and using a 21mm wrench. Install the shock in the upper mount with supplied stem bushings, cup washers & nuts using a 9/16” wrench. 44. Install the tires and wheels and jack up the vehicle to remove the jack stands. Lower the vehicle to the ground. 45. Tighten control arm hardware using a 18mm & 24mm wrench. Photo 32 Install the stock cross-member on brackets Photo 33 Install shock absorbers REAR INSTALLATION 1. Chock the front wheels and jack up the rear of the vehicle. Support the vehicle with jack stands. Remove the tires/ wheels using 7/8” deep well socket. 2. Remove the factory shocks using a 21mm wrench and discard. 3. Support the rear axle with a floor jack and remove the factory u bolts. 4. Install the block on the axle and make sure the block and axle pin align. See Photo 32. 5. Install the supplied 7/16” u-bolts, washers, and nuts on the leaf springs, securing the block to the springs. Do not tighten at this time. See Photo 33. Photo 32 6. Grinding may be required on the driver side e-brake bracket on the lower shock mount. If needed grind the threads to make sure there is no interference with the shock absorber. This must be done if there is interference with the shock. Failure to complete this modification may damage the shock absorber body and void all shock warranties. 7. Assemble the shocks part # 658556 with supplied bushings /sleeves and install the new shocks with the factory bolts and nuts using a 21mm wrench. See Photo 34. Note: The rear shock is a slim bore design due to limited clearance between the shock body and the axle tube. 8. Install the wheels and tires. Tighten lug nut to factory specifications using crossing pattern. Lower the vehicle to the ground. 9. Tighten the lug nuts to 85 ft lbs. Photo 33 Photo 34 LOWER ARM TEMPLATE (PLEASE CHECK TO MAKE SURE THE HOLE IS CENTERED PRIOR TO DRILLING) DRIVER SIDE PASS SIDE POST INSTALLATION INSTRUCTIONS 1. Check all fasteners for proper torque. Check to ensure for adequate clearance between all rotating, mobile, fixed, and heated members. Verify clearance between exhaust and brake lines, fuel lines, fuel tank, floor boards and wiring harness. Check steering gear for clearance. Test and inspect brake system. 2. On some vehicles the front lower skirting will need to be trimmed if using certain wheel /tire combinations and with heavy offset wheels. Trim only as needed. 3. Activate four wheel drive system and check front hubs for engagement. 4. Have a qualified alignment center align the vehicle immediately. Realign to factory specifications. Have headlights adjusted to proper settings. 6. Perform head light check and adjustment to proper settings. 7. Check and retighten wheels at 50 miles and again at 500 miles. 8. Recheck lifted height and adjust torsion bar as necessary. 9. All kit components must be retightened at 500 miles and then every three thousand miles after installation. Periodically check all hardware for tightness. 10. Install “Warning to Driver” decal on sun visor. Note: Installation of larger tires will require speedometer recalibration. OPTIONAL EQUIPMENT Rough Country offers two optional items for this vehicle when lifted with our suspension system. Both of these items are highly recommended, but not required. Part # 87320 is a single steering stabilizer kit and will help with 35” tires to reduce front end wonder and steering integrity. Also available is a set of kicker braces that add stability to frame for off road performance. Please contact your Rough Country distributor to order. Optional Equipment: Part # 1272 Box4-Kicker Braces Thank you for choosing Rough Country for all of your suspension needs.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2011:07:19 10:08:31-05:00 Create Date : 2011:07:19 10:08:31-05:00 Format : application/pdf Title : 1272 99-06 1500 6inch lift kit.pub Creator : cbeaver Producer : Acrobat Distiller 8.3.0 (Windows) Document ID : uuid:9229763a-ea18-4b3f-b280-8d8cc633643b Instance ID : uuid:5c36a9cd-e089-4b8f-8f20-763fb99cadee Page Count : 12 Author : cbeaverEXIF Metadata provided by EXIF.tools