Peavey Electronics PV10 Audio Mixer User Manual 15 PV 10AT UserMan

Peavey Electronics Corporation Audio Mixer 15 PV 10AT UserMan

15_PV 10AT UserMan

www.peavey.comPV®10AT • PV®BT Compact MixerOperatingManualLEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112345/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10ATPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlySIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTEAuto-TUNEAuto-TUNEAT AT
Features and specifications are subject to change without notice.Peavey Electronics Corporation • 711 A Street • Meridian, MS 39301 (601) 483-5365 • FAX (601) 486-1278 • www.peavey.com © 2015 EX000030FCC/ICES Compliancy StatementThis device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS Standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, that may cause undesired operation.Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) I’appareil ne doit pas produire de brouillage, et (2) I’utilisateur de I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Warning: Changes or modifications to the equipment not approved by Peavey Electronics Corp. can void the user’s authority to use the equipment.Note – This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures.• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.• Consult the dealer or an experienced radio/TV technician for help.CautionThe equipment complies with FCC radiation exposure limits set forth for an uncontrolled envi-ronment.
PV®10AT and PV®10BT Compact MixersCongratulations on purchasing the Peavey PV®10AT or PV®10BT Compact Mixer. e PV®10AT and PV®10BT are studio-quality mixing con-soles designed to meet diverse needs while occupying a small space. ese are the perfect consoles for small venue performances or home record-ing environments. PV series mixers feature built-in DSP eects that are useful in real-world recording and sound reinforcement, while parameter controls allow you to tailor each eect to meet your needs. e PV 10 BT includes 4 channels of reference-quality mic preamps, 4 direct outputs for recording, a stereo channel, media channel with Blue-tooth wireless input, high quality digital eects with LCD display, streaming USB out, MP3 playback via USB A input, Peavey's exclusive Kosmos audio enhancement, 48 volt phantom power, dual selectable control room outputs, 2 channels of compression, one channel of on board selectable guitar preamp, 3-band EQ per channel with bypass, channel mute buttons, aux send, signal clip indicators, and a stereo master LED meter bridge. is amazingly versatile mixer is at home both in the studio as well as live applications. Its modern features such as Bluetooth allow seamless connection to almost any "smart" device. 4 direct outs allow easy connection to most DAW interfaces for recording; in addition, the PV 10 BT can stream audio directly to a PC. MP3 playback is also available, just plug a ash drive with MP3 les on it into the USB A port and use the LCD to select and playback music. e PV series Solo feature allows the user to listen to individual channels via headphone or control room outputs and the EQ bypass allows the user to compare the EQ'd signal to the original signal with the push of a button. 2 Channels of compression keep signals with dicult levels under control, and Peavey's exclusive guitar-shape adjusts the EQ and preamp specically for guitar. Hi pass lters on every channel remove unwanted rumble and noise, and balanced AUX and Master outputs ensure a clean noise free signal to your powered speakers or power amplier. e all new PV series non-powered mixers represent the pinnacle of performance and value. Combine Peavey's legendary reli-ability and our 5 year warranty and you can be assure of years of quality reliable service, we guarantee it.In addition to all of these features, the PV10AT features 2 channels of Antares® world-famous Autotune®, which can be set to subtly tighten up vocal harmonies, or it can be set for robotic vocal eects heard in today's popular music. Peavey's exclusive custom key feature makes it a snap to auto-tune to any scale you can think of, in a live performance. It is so easy and fast, you can set it up between songs, right in the middle of a set.Please read this guide carefully to ensure your personal safety as well as the safety of your equipment.FEATURES:ENGLISHInstallation Note:is unit must have the following clearances from any combustible surface: top: 8", sides: 12", back: 12"• 4 Combination 1/4" and XLR low noise mic preamps• Stereo 1/4", RCA or 3.5mm input channel• Bluetooth wireless connectivity• 3-band EQ on all channels• 4 Channels of Peavey's Exclusive Mid-Morph• 150 Hz low-cut switch on all mic inputs• LED clip and signal present indication• Individual channel mutes• EQ Bypass per mic channel• On board studio quality digital eects with individual channel control• Eects and playback LCD display• One pre-fader AUX send• Precision 60 mm faders on master• Dual selectable control room outputs / Record out with independent level• Global 48V phantom power• Main stereo outputs with balanced 1/4" and XLR connectors• Rugged console design• 2 channels of built-in compression• Stereo pan control per channel• On-board USB-A MP3 playback• 4 Channels of direct out• Kosmos -C bass and treble enhancement• Channel 9/10 stereo return/input• Individual Solo function• Stereo USB-B streaming audio in and out• High quality master LED meter bridge• Master mic mute• Studio quality headphone output• Peavey's exclusive on-board 1 Meg guitar input• Antares Auto-Tune with Peavey's exclusive Custom Key feature
MIC/LINE INPUT (CH.1-8)is combination input jack accepts a ¼” or XLR balanced plug. e XLR balanced input is optimized for a microphone or other low impedance source. e ¼” input is a TRS balanced type, and also accepts ordinary TS guitar cables.DIRECT OUTis impedance-balanced TRS output signal is taken aer the mic preamp, hi pass lter, and compressor, but before the EQ stage.AUTO-TUNE ACTIVATION BUTTON AND LED (PV10AT only)Pressing this button activates the PV10AT's onboard AUTO-TUNE feature. e button illuminates when in AUTO-TUNE mode (SEE Eects Select {50} and the following page). GAINe Input Gain control is used to establish proper gain structure in the channel. For best results, use the Solo system (19) to monitor the channel while you set the gain. e goal is maximum gain without distor-tion. Both the main LED meters (during Solo) and the channel’s Signal/Clip indicator (16,17) can be used for adjusting gain. If the clip LED (16) comes on and remains lit, try reducing the gain.150 Hz HI PASS FILTERe hi pass lter has a corner frequency of 150 Hz. When engaged‚ it can improve clarity by removing low frequencies that make a mix sound muddy. is feature is especially useful when playing outside on a windy day or on a hollow-sounding‚ noisy stage. ese kinds of ambient noises can rob your sound system of power. Engaging this switch will remove those frequencies from the system and restore power where needed.COMPRESSION CONTROL (Channels 1 and 2 only)Adjusting this knob clockwise lowers the threshold of the compressor, thereby increasing the amount of compression. e compressor ratio is in the 4:1 range, varying with signal levels and the amount of com-pression. is is useful for controlling peak levels from live sources, and has been designed to subtly tame the levels of live vocals without noticeable artifacts. e compressor is aer the gain control (5) and the hi pass lter (4), but before the direct out (2), so it can be patched to external equipment. Compressor LEDis LED illuminates when the compressor is actively compressing a signal. Hi EQis active tone control (shelving type: ±15 dB) varies the level of the high frequency range.MID-MORPH EQ (CH. 1-7)Where most mid-range controls work at just one frequency, the Mid-Morph works at two. When turned counterclockwise, it cuts at 250Hz to reduce frequencies that muddy the sound. When turned clockwise, it boosts at 4kHz to add intelligibility to vocals. Either way, improved vocal or instrument denition can be achieved.Low EQis active tone control (shelving type: ±15 dB) varies the level of the low frequency range. Caution: Ex-cessive low frequency boost causes greater power consumption and increases the possibility of speaker damage.EQ BYPASSEngaging this button bypasses the equalization of the channel, allowing you to easily hear the eect of the EQ settings.AUX SEND is control adjusts the level of the channel signal sent to the Aux output. e signal is taken before the channel level (18) but aer the channel EQ, meaning that changes to the EQ settings will aect the aux mix, but changes to the channel level control won't. Typical use for the Aux bus is to feed stage monitors, when used in a live performance, or to feed headphone ampliers in a recording situation. 12345689101112131415181971617PV10AT Front Panel (channels 1 and 2)123479568101112LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112345/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10ATPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlySIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTEAuto-TUNEAuto-TUNEAT ATLEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112345/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLOSOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASSEQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10ATPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlySIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTEAuto-TUNEAuto-TUNEATAT
EFX SENDis control adjusts the level of the channel signal added to the eects mix. e signal is sent to the internal eects processor. Turning the knob to the le (min) will turn o eects on the associated channel, while turning the knob to the right will increase the amount of the selected eect. e eects send signal is taken aer the channel level (18) so that adjustments made to the fader will also aect the send level.PAN CONTROLis knob controls the placement of the signal in the stereo eld. When rotated completely counterclockwise‚ the signal is present only on the le channel; when rotated completely clockwise‚ only in the right channel. is control functions as a balance control to adjust the relative level of the le and right signals on stereo channels 5/6 and 7/8. (Note 1/4" inputs on ch 5-6 and 9-10 are mono unless both are connected, then they switch to stereo)MUTE SWITCHPressing this switch will silence the channel signal going to the main mix, aux send, and eects. e mute switch will not aect the signal sent to the solo system. CLIP/MUTE LEDis LED normally indicates that the channel signal level is near clipping (distortion), but it also lights when mute is engaged. e clip indicator circuit monitors the signal aer the gain control, aer the EQ, and aer the main level; because clipping can be caused by high settings of any of these controls. It illuminates at +15 dBu with a static signal (test tone), and corresponds to audible clipping with a highly dynamic signal (i.e. piano). When lit, it warns that the gain or EQ boost should be reduced. When it lights, roughly 5 dB of headroom remains. An optimized setting of input gain + EQ will result in this LED ashing briey on the loudest peaks.SIGNAL LEDe signal LED lights when the channel level reaches approximately -20 dBu. is not only indicates which channels are active, but also serves as a mini level meter. Because its illumination varies with the signal source, it is useful in identifying which channel is carrying a particular source. CHANNEL LEVEL CONTROLis is the channel's output control, which sets the signal level sent to the le and right mix and the eects send control. e gain is 0 dB (uni-ty gain) when set to the detent at mid-rotation (12:00). 10 dB of boost is available at the max gain setting. Normal operation is to start with this knob at the detent, and set the input gain and EQ with the source playing such that normal levels are seen at the signal /clip LED's and the main meter array. As additional sources are added, it is normal to turn this knob down slightly to prevent overdriving the main mix bus. SOLO SWITCH AND LEDWhen the Solo switch is engaged, the yellow LED lights, as does the yellow Solo LED under the main L/R meter array in the master sec-tion, indicating that the Solo system is now active. e Solo system is a separate mix bus that routes the soloed channel(s) at unity gain to the level meters for precise input level setting, and to the control room monitor and headphone outputs for critical listening to the selected source(s). When the Solo system is active, the complete mix will no longer be heard through the control room or headphones; only the soloed channel(s). PV10AT Front Panel (channels 1 and 2)131415161718192021PV10AT Front Panel (channel 4)MIC/LINE INPUT (CHANNEL 4 ONLY)is input is the same as channels 1-3 unless Guitar Shape is pressed. When ELECTRIC GUITAR PRE-SHAPE is on, the 1/4" input changes to a high impedance (1 MegΩ), like a 12AX7 vacuum tube guitar amplier input.Electric Guitar Pre-ShapeEngaging this button optimizes the on board equalization for electric guitar.LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112 3 4 5/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10BTPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlyPOWERSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTELEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112 3 4 5/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUTDIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10BTPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlyPOWERSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTE2021
LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112 3 4 5/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLOSOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN7/812345/6 7/8min maxMIDPV 10BTPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlyPOWERSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTELEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112 3 45/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10BTPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlyPOWERSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTEPV10AT/PV10BT Front Panel (channels 5, 6, 7 and 8)222326282924252730222324252627283.5mm STEREO INPUTe 3.5mm input to channel 5/6 accepts a stereo input from the output of an MP3 player, CD player, tape deck or other similar device. is input is optimized for portable hand-held devices and therefore has very high sensitivity.STEREO INPUTSChannels 5 and 6 also feature 1/4" inputs. If only one jack is used, it behaves as a mono source with a pan control. When both jacks are connected, these connections serve as a stereo source with a balance control; 5 is Le and 6 is Right.USB MEDIA JACKA-type USB connector that a removable data storage device can be connected to playback musicUSB PLAYBACK:First, slide the input selection switch (27) to the USB A position. e bottom of the LCD display will say “Insert USB drive”. Insert your USB drive into the USB Media Jack (24) at the top of channel 7/8. e Media Player will now enter "Folder Navigation Mode". In this mode, you can scroll through a list of all folders on the USB drive. Once you select a folder, the Media Player will enter "Song Navigation Mode" which allows you to scroll through a list of all songs contained in the selected folder. If there are no songs in the selected folder, the LCD will display "No Songs". To return to Folder Navigation Mode, scroll to the very beginning of the list and select the <FOLDERS> option.Once a song is nished playing, the Media Player will automatically start playing the next song. Once the Media Player reaches the last song, it will automatically loop back to the beginning of the list.BLUETOOTH PAIRING BUTTON AND LEDe Bluetooth Pairing Button is used to turn on/o the Bluetooth. e blue “Bluetooth Active LED” indicates the status of the Bluetooth connection. If the LED is o, the Bluetooth module is powered o. If the LED is slowly ashing, the PV mixer is not paired with any device, but is available for connection. When the LED is lit solid, the source device is properly paired to the mixer and ready to play.e PV Mixer will remember up to 10 devices that it was previously paired with and will automatically connect to the last device with which it was paired when turned on. To clear the paired device memory, make sure Bluetooth is on and press and hold the Bluetooth Pairing Button for 5 seconds. e PV mixer will ask if you would like to clear the Bluetooth memory. Select "Y" using the Media Select knob to clear the memory. e PV mixer will go through the process of clearing the memory, which should take approximately 15 seconds.RCA MEDIA INPUTSe RCA inputs to channel 5/6 accept a stereo source such as an MP3 player, CD player, tape deck or other similar device. is input is optimized for portable handheld devices and therefore has very high sensitivity.DIGITAL SOURCE SELECTORis switch selects between USB A (24), USB B (68), and the internal Bluetooth receiver.MID CONTROLStereo channels' midrange is +/-20 dB @ 440Hz ; the HIGH (8) and LOW (10) controls are described above.
31302932333435LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112 3 4 5/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10BTPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlyPOWERSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTE31333234 35PV10AT/PV10BT Front Panel (channel 4)ANALOG BALANCE CONTROLControls the balance between the analog channels 5/6. DIGITAL BALANCE CONTROLControls the balance between the digital channels 7/8.AUX SEND XLR and 1/4" OUTGround compensated balanced output fed by the AUX SEND master level (52). e XLR is internally in parallel with the TRS. You will get better hum and noise rejection by using balanced interconnects (either XLR or TRS), but unbalanced Tip Sleeve (TS) cables will also work.FOOTSWITCHis TRS jack is designed for use with Peavey's 2 Button Special Use Momentary Footswitch, Item # 03014070. e tip of this TRS jack, switch 1, remotely actuates the EFX Mute switch. e ring of the TRS jack, switch 2, remotely turns o the Auto-Tune on AT models. is makes the use of Auto-Tune inconspicuous; by using the footswitch, your between-songs spoken banter won't be Auto-Tuned.1/4" STEREO INPUTSChannel 9 and 10 are a stereo pair of 1/4" jacks that can be used for an aux input, or eects return from an external processor.If only one jack is used, it behaves as a mono source. Once both jacks are connected, it behaves as a stereo source; 9 is Le and 10 is Right.1/4" STEREO OUTPUTSGround compensated balanced output fed by the master L and R Faders (60). e TRS jacks are internally in parallel with the XLR's. You will get better hum and noise rejection by using balanced interconnects (either XLR or TRS), but unbalanced Tip Sleeve (TS) cables will also work.XLR STEREO OUTPUTSGround compensated balanced output fed by the master L and R Faders (60). e XLR jacks are internally in parallel with the TRS's. You will get better hum and noise rejection by using balanced interconnects (either XLR or TRS).
LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112345/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin maxREC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10ATPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlySIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTEAuto-TUNEAuto-TUNEAT AT3639 40 4243444137PV10AT Front PanelPHANTOM POWERis Switch applies +48 VDC voltage to the input XLR connectors to power microphones requiring phantom power. If phantom power is used, do not connect unbalanced dynamic microphones or other devices to the XLRinputs that cannot handle this Voltage.STEREO IN LEVEL 9/10Controls the level of input jacks 9 and 10. If only one jack is connected, it is sent to both L and R. If both jacks are connected, 9 is L and 10 is R. e Aux output could be fed to an external eects processor, and these jacks could be used as the eects return. Or a second mixer could be daisy-chained in here.LEVEL A/BControls the level of both A and B control room outputs. e active output is selected with A/B SELECT switch (41), when B/REC switch (42) is up. When B/REC switch is down, only output A is controlled.REC LEVELWhen B/REC switch is down, controls the level at the B/REC outputs. Note: When B/REC switch is up, this control is inactive.A/B SELECTWhen this switch is up, output A is on and output B is o. When this switch is down, output B is on and output A is o. Use this switch to evaluate a mix on 2 dierent pairs of monitors, such as near eld and far eld monitors. By setting the level controls on both monitoring sys-tems the same, a rapid A/B comparison can be made. Overall monitor level is controlled by LEVEL A/B. NOTE: When the B/REC switch (42)is down, this switch is disabled , and the A output remains on at all times, fed by LEVEL A/B (39).B/REC SWITCHDetermines the function of the B/REC output. When up, B/REC jack functions as monitor B output, selected by A/B select and controlled by LEVEL A/B. When down, B/REC jack is an independent record output, with level controlled by REC LEVEL.CONTROL ROOM MONITOR OUTPUT AConnect powered monitors, or an amplier feeding monitor speakers here. Set the volume controls on the monitors A and B to be equal when the A/B switch is toggled. e signal sent to this output is normally the Le/Right mix. e USB "To Control Room" pot (47) feeds the USB return signal to these Monitor Outputs for use in a DAW recording setup. When the Solo LED is lit (62), only the soloed source(s) will be heard. NOTE: When the B/REC switch is down, the A/B SELECT switch becomes disabled, and this output is output is controlled by the LEVEL A/B control.36373940414243
4445464748495051PV10AT Front Panel 464950514547 48LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112345/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRL left rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRL left rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10ATPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlySIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTEAuto-TUNEAuto-TUNEAT ATCONTROL ROOM MONITOR OUTPUT B / RECORD OUTis pair of outputs can either serve as your "B" Record Monitor Output; or, with the B/REC switch (42) down, as an independently controlled Record Output. NOTE: When the B/REC switch is down, the A/B SELECT switch becomes disabled, and this output is output is controlled by the B/REC control.USB RECORD LEVEL KNOBControls the level of signal sent to the USB B connector on the back of the mixer. e recommended setting is near 12:00, but a wide range is available to accommodate varying levels and sensitivites.CONTROL ROOM LEVELControls the level of signal returning from the USB B connector on the back of the mixer. e signal is routed to the control room and head-phone outputs, for multitrack recordings on a DAW. e recommended setting is near 12:00.MEDIA AND EFFECTS LCD DISPLAYe top row of this LCD displays the currently selected Eect and the bottom row displays the statusof the MP3 Player, which can be used for navigating the folders on the USB drive or displaying the current song playing. e bottom line will also briey display the Bluetooth status during power on, power o, and memory clearing.MEDIA SELECTOnce a USB device is connected in channel 8, you can use the “Media Select” encoder to navigate through the folders/songs on the drive. Once the desired le is displayed on the screen, press the Media Select knob to cue that le. Use the controls on the mixer for play, pause, forward and reverse. EFX SELECT KNOBSee detailed description on the following page.MEDIA PLAYBACK CONTROLSese controls allow you to play, pause and scroll though digital media via USB jack. AUTO-TUNE ACTIVATION BUTTON (PV10AT ONLY)Pressing this switch changes the top line of the LCD between Auto-Tune Edit Mode and EFX Edit Mode. is funtion is not available in the PV10BT.
PV10AT Front Panel EFX Select Knob:EFX Mode:In EFX Edit Mode (see Auto-Tune Switch), the EFX Select knob is used to navigate through the EFX presets. Turning the knob changes the EFX preset in the display. e new selection will be blinking in the display; push the EFX Select knob to choose the new eect. Once the ef-fect has been selected, you can now edit the eect. To do this, press the EFX Select knob and the display will change to the current parameter setting of the preset. Turn the EFX Select knob to edit the parameter. Press the knob again to exit EFX preset edit mode. To restore the EFX presets back to factory settings, press and hold the EFX Select knob for 5 seconds and select "Y" when prompted.Auto-Tune Mode:In Auto-Tune Edit Mode (see Auto-Tune Switch), the EFX Select knob is used to navigate through the Auto-Tune presets. Turning the knob changes the Auto-Tune preset in the display. e new selection will be blinking in the display; push the EFX Select knob to choose the new Auto-Tune preset. Once the preset has been selected, you can edit the preset by pressing the EFX Select knob. e display will change to the current Key setting. Turn the EFX Select knob to change the key and push the EFX Select knob when you have chosen the key you desire. e Key setting deter-mines which notes are enabled in the Auto-Tune process. For example, in the key of CMaj, the notes C, D, E, F, G, A, and B are enabled, and all other notes are disabled. To see which notes are enabled or disabled for each key, see the Key Table below.Note: If Custom Key is selected, the display will enter Custom Key Edit Mode. In this mode, you can create a custom Auto-Tune Key. Use the EFX Select knob to select the Root (labeled "RT"). is will be the note o which the custom key is based. en use the Media Select knob to move the cursor and use the EFX Select knob to activate or deactivate the 12 notes in the key. Once you have nished editing the custom key, press the EFX Select knob to exit Custom Key Edit Mode. e mixer is capable of storing 9 dierent custom keys, one for each preset slot.e scale degrees are numbered across the top, with half-steps indicated by a dash. "+" indicates the note will be allowed. "-" indicates the note will not be allowed. By looking at the sequence of allowed and disallowed notes above, this is a whole tone scale. ere are only two of those, so you can have the other one just by changing the root to C# or B.*is screen cap shows an A blues scale. You don't have to edit the whole scale to change keys - just change the root.Once you have selected the key and pressed the EFX Select knob, the display will change to the current Speed setting. Turn the EFX Select knob to change the Speed setting. e Speed setting determines how quickly and aggressively the Auto-Tune will correct the pitch. e range for this setting is 0 to 25, where 0 is the quickest and 25 is the slowest. Push the EFX Select knob when you are done editing the speed param-eter. *RT=Scale Degree *Key = indicates the root or key is C RTKey
Auto-Tune Key TableAuto-Tune Key TableKey Display Note Number (n)= Key 0 1 2 3 4 5 6 7 8 9 10 11Chrom C C# D D# E F F# G G# A A# BC Maj C D E F G A BC Mnr C D D# F G G# A# C#Maj C C# D# F F# G# A# C#Mnr C# D# E F# G# A BD Maj C# D E F# G A BD Mnr C D E F G A A# D#Maj C D D# F G G# A# D#Mnr C# D# F F# G# A# BE Maj C# D# E F# G# A BE Mnr C D E F# G A BF Maj C D E F G A A# F Mnr C C# D# F G G# A# F#Maj C# D# F F# G# A# BF#Mnr C# D E F# G# A BG Maj C D E F# G A BG Mnr C D D# F G A A# G#Maj C C# D# F G G# A# G#Mnr C# D# E F# G# A# BA Maj C# D E F# G# A BA Mnr C D E F G A BA#Maj C D D# F G A A# A#Mnr C C# D# F F# G# A# B Maj C# D# E F# G# A# BB Mnr C# D E F# G A Be display will now change to the current Detune setting. Turn the EFX Select knob to change the Detune setting. e Detune setting determines how the Auto-Tune pitch correction is calibrated. When the Detune setting is 0 cents, this means the Auto-Tune is calibrated to the standard A440, or where the note A4 equals 440 Hz. e range of the Detune setting is -64 to 63 cents, a width of 128 cents. e distance between two notes, or semitones, is 100 cents, which means that the Auto-Tune can be detuned to t any possible environment.Note: Detuning the Auto-Tune can be very useful, especially when being used in conjunction with an instrument that is not easily tuned on-the-y. For example, if a piano is accompanying Auto-Tuned vocals and the piano is slightly out of tune from the A440 stan dard, simply change the Detune setting in the Auto-Tune setting. is is much easier and takes much less time than having some one tune the entire piano! Also, although the Detune setting is changed in the Auto-Tune preset edit mode, this is a global param eter. is means if you change the Detune setting and then later change the Auto-Tune preset, the Detune setting will not change.Once you have selected the appropriate Detune setting, press the EFX Select knob to exit Auto-Tune preset edit mode. To restore all Auto-Tune presets back to factory settings, press and hold the EFX Select knob for 5 seconds and select "Y" when prompted.Note: Preset 9 is chromatic with speed set to 7. It is recommended for general purpose, safe, easy use of Autotune, without having to adjust any settings. e slower speed setting does not produce a robotic eect on the voice, and all twelve semitones are allowed. Just remember to use footswitch #2 to bypass Autotune between songs, otherwise your speaking will be Autotuned!
LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112 3 4 5/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10BTPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlyPOWERSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTEPV10AT Front PanelAUX MASTER CONTROL KNOBControls the overall level of the signal coming out of the Aux Output (31). is Auxiliary output is typically fed to a power amplier to drive stage monitors so singers can hear themselves amidst amplied instruments, or to a headphone amplier to give vocalists a monitor feed that will not be picked up by microphones while recording.AUX MASTER SOLO BUTTON AND LEDAllows you to listen to just the Auxiliary mix. e setting of the AUX MASTER knob determines the level you will hear when this button is pressed.EFX RETURN SOLO BUTTON AND LEDAllows you to listen to just the eects return. e setting of the Return to Main knob determines the level you will hear when this button is pressed.RETURN TO AUX CONTROL KNOBis control determines the level of the internal digital eects processor being sent to the Aux output. One possible use is to put reverb in the headphones of a vocalist, to give them a condence boost for recording, without putting any reverb on the actual recorded track. Or in a live situation, the same can be done by feeding a delay or reverb to the monitors.EFX RETURN TO MAINis control determines the level of the internal digital eects processor being sent to the main L and R outputs.EFX MUTE BUTTON AND LED/CLIP LEDWhen depressed, the output of the internal digital eects is shut o. Muting the eects is an easy way to determine what a particular eect is doing to your mix. LED remains lit when EFX MUTE is engaged. When EFX MUTE is not engaged, this LED functions as a clip indicator for the internal digital eects. If the digital eects are clipping, reduce the level of the EFX SEND pots.52 53 555760565859616254525354555657
PV10AT Front PanelSTEREO/MONO MODE SWITCHIn the mono position, the le and right buses are summed together aer the faders. In this position, the L fader controls the level of the L bus, and the R fader controls the level of the R bus, allowing you to use the L and R buses as groups. For example, all vocals could be panned L and all instruments panned R. en the L fader becomes the vocal master level and the R becomes the instruments master level.MIC MUTE BUTTON AND LEDDepressing this button mutes all of the mic inputs channels (1-4) and the eects return. e media input channels are still "live". is allows you to play break music, while muting all of the microphone inputs.MAIN LEVEL FADERSe Master Faders control the levels sent to the Main Le/Right outputs (34, 35). Best results are obtained when these controls are set near the midpoint of the enclosed rectangle.MAIN L+R METER ARRAYDisplays the level of the L and R outputs, or, when solo is active, displays the soloed channel(s). e top green LED corresponds to an output level of +4dBu. e red LED is a clip warning indicator. e range of the meter is from -17 dBu to + 15 dBu.MAIN SOLO LEDLights when any solo button is pushed, to indicate that the solo system is active.5859606162
LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxLEVELCOMPmin maxSIGNALCLIPGAIN3.5mm STEREOMAIN OUTPUTSSTEREO INFSAUX SENDMAIN L+R 112 3 4 5/6 7/8min maxDIRECT OUTRLLLRRPHANTOM POWER 48VUSB ASOLO/MAINCONTROL ROOMSOLO/MAINUSBmin maxHEADPHONE/SOLO/MAINDIRECT OUTSOLOSOLO SOLO SOLO SOLO SOLO SOLO56RLRL109RLRLPress toSelectPress toSelector editEFX SELECTMEDIA SELECTDIGITAL EFFECT/MEDIA PLAYBACKUSB MEDIA PLAYBACKEFFECtsmediamin maxmin maxcompDIRECT OUT DIRECT OUTHI PASSMIC MUTEMUTEMASTERmin maxRETURN TO MAIN RETURN TO AUXDIGITALMEDIA CHANNELLEVEL A/Bmin max REC LEVELmin maxRECORD LEVELmin maxTO CONTROL ROOMmin maxANALOGMEDIA CHANNELRLEFXAUX STEREO IN LEVELmin maxENABLEA/B SELECTB/RECKOSMOS-Cmin maxmin maxHIGHLOWUSB AUSB BBluetoothMONO(SUM)STEREOAB/REC10 INPUT STEREO MIXER WITH DIGITAL EFFECTS, MEDIA PLAYBACK AND BLUETOOTHEQ BYPASS EQ BYPASS EQ BYPASS EQ BYPASSPAIRINGMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxCOMPmin maxGAIN2min maxcompHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN3min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxPANcRLleft rightEFXmin maxAUXmin maxGAIN4min maxHI PASSMID-MORPH0low high-+LEVELmin maxHIGHLOW0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN5/6min maxMIDLEVELmin maxHIGHLOW0-+min max0-+min max0-+min max0-+min maxBALcRLleft rightAUXmin maxGAIN7/81 2 3 4 5/6 7/8min maxMIDPV 10BTPV 10ELECTRIC GUITAR PRE-SHAPE9/109/10EFX MUTESOLOSOLO1/4”-Hi-Z CH.4 OnlyPOWERSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPSIGNALCLIPMUTEMUTEMUTEMUTEMUTEPV10AT Front PanelKOSMOS-C HIGH CONTROLA very selective high frequency lter with a high Q. e eect varies with source material, so some experi-mentation is required for optimum results.KOSMOS-C LOW CONTROLis Kosmos-C Low enhancement works by creating harmonics of signals in the bottom ocave, where speakers are usually ineective. e harmonics are more easily reproduced, resulting in a perception of stronger bass. e eect is source dependent; obviously a source with little energy in the bottom octave will not create booming bass.KOSMOS-C ENABLEAllows you to easily A/B the eects of your Kosmos Settings.HEADPHONE SOLO/MAIN LEVELControls the level of the headphones. e headphone is normally fed by the main outs, unless the solo system is active. Always start with the headphone level at "min" to avoid hearing damage.6364656663646566
PV10AT/PV10BT DC POWER INLETUse to connect the included power supply. Be sure the power supply is connected to the PV®10 before connecting to a power source. Use 15VDC, 1A adapter only. Replace only with Peavey part number 30908119.POWER SWITCHis is the main power switch.USB PORT TYPE Be USB port is used to connect the PV® Series USB mixer to a computer for recording or playing back digital audio to/from your computer. e USB port sends the mixer’s main/tape stereo out to the computer. e USB port receives digital audio from the computer; it can then be assigned through the selector switch (27) to the main le/right output, if the computer is being used for playback only. For recording, use the USB TO CONTROL ROOM control (47), to avoid creating a loop. Compatible with Windows® Vista, Windows 7, & Windows 8, Mac OS X® 10.0 or later, and iOS devices.67 68 69676869POWERONDIGITAL AUDIOPORTCOMPUTER
Block Diagram-PV®10AT & PV®10BTLO80Hz4kHzMID-MORPH12kHzHI400HzLO80Hz4kHzMID-MORPH12kHzHI400HzPANHI PASSBALANCEBALANCEEQLO MID HIPeavey Electronics Corp.4321D4321CBAA B C DSheet Title:Title:Sheet Date:ofDCONFIDENTIALMeridian, MS 393055022 Hartley Peavey Drive+48VPANEQLO MID HIHI PASSCHANNEL 5/6MuteMUTESoloEFX ReturnLevelRecordRecordAUXSIGNALEFXCLIPAUTO-TUNEON/OFFEQBypassEQ LEVELDirect OutputCOMPThresholdSoloMICMUTESoloOUTOUTOUTLEFTRIGHTAUXAUXCLIPEFXEQLEVELSIGNALGuitarLINERIGHTON/OFFSELECTOREFXDEFEATSIGNALEFXEFXLOWINPUTBLUETOOTHMEDIASELECTORHIGHCLIPSTATUSAUTO-TUNEKOSMOS - CXLRLINEON/OFFEFFECTSGainMIC PREEQBypassEQLEFTRIGHTLEFT3.5mm InLEVELDirect OutputMuteMIC PREGainEQGuitarInCOMPThresholdXLRCLIPEFXEQLEVELSoloSIGNALInputSelector AUXMonoLEFTAUXSoloKOSMOS ENABLEAUXLeftRightRightMasterLeftSoloRIGHTHeadphoneMasterCLIPControl Rm ASoloLevelControl RmLevelLevelHeadphoneA/BSelectRecord OutB/Record OutControl Rm B/USB BUSB AEFXEFX InEFX OutTo MainsTo AUXEFX ReturnMUTEMICFOOTSWITCHSOLOMEDIA PLAYERMuteMuteT = EFX MuteR = AutoTune Bypass (AT Models)CHANNEL 1 - 3Ch 1-2 OnlyCh 1-2 OnlyCH 1-2 ONLYCH 1-2 ONLYLeft 1-4Right 1-4CHANNEL 4CHANNEL 7/8CHANNEL 9/10To USB B Streaming OutputMedia PlayerInputStreamingInput231132231PHANTOMPHANTOMPV10_BLOCK4-9-2015_11:362 2231132
PV®10AT & PV®10BT Series SpecicationsInputsFunction Input Z(ohms min)Input Gain Setting Min** Nominal* MaxBal/UnbalConnectorMicrophone(150 ohms)2 kΩ Max Gain(59 dB)Min Gain(4 dB)-71 dBu-17 dBu-51 dBu+5 dBu-39 dBu+16 dBuBal XLR Pin 1 GndPin 2 (+)Pin 3 (-)Line(10 k ohms)Line 4 TS, GTR SHAPE ON10 kΩ1 Meg Ω @ ≤ 200 Hz, like 12AX7 input.Max Gain(40 dB)Min Gain(-15 dB)-52 dBu+2 dBu-32 dBu+23 dBu-20 dBu> +32 dBuBal 1/4" TRS;Tip (+)Ring (-)Sleeve GroundStereo Input 5/6Stereo Input 9/1010 kΩ6.8 kΩMax Gain (18 dB)NominalMax Gain ( 18 dB)Nominal-31 dBu-13 dBu-23 dBu-15 dBu-12 dBu+6 dBu-13 dBu-5 dBu+1 dBu+19 dBu+3dBu+12 dBuUnbal 1/4" TS;Tip (+)Sleeve Ground3.5mm, RCA 2.8 kΩ Max Gain (18 dB) Nominal-43 dBu-24 dBu-23 dBV-5 dBu-10 dBu+8 dBuUnbal 3.5mm; Tip=L, Ring = R, Sleeve GroundRCA: Tip (+),Sleeve GroundInput Levels0 dBu=0.775 V (RMS)** Min Input Level (sensitivity) is the smallest signal that will produce nominal output (+4 dBu) with channel and master faders set for maximum gain. * Nominal settings are dened as all controls set at 0 dB (or 50% rotation for rotary pots) except the gain adjustment pot which is as specied.OutputsFunction Min Load Z(ohms)Nominal Max Bal/UnbalConnectorMain Left/Right 600 +4 dBu +20 dBu Bal XLR Pin Ground TipPin 2 (+), Pin 3 (-)1/4" TRS: Tip (+), Ring (-) Sleeve GroundEects and Monitor Sends600 +4 dBu +20 dBu Bal 1/4" TRS: Tip (+), Ring (-) Sleeve GroundControl Room 600 +4 dBu +20 dBu Unbal RCA: Tip (+),Sleeve GroundHeadphone 8 +4 dBu (no load) +20 dBu Unbal 1/4" TRS; Tip Left, Ring Right Sleeve GroundOutput Levels0 dBu=0.775 V (RMS)Mic pre EIN = -126 dBu @ max gain with 150 ohm source
GainFrequency ResponseTotal Harmonic DistortionHum and NoiseEquivalent Input Noise Mic Input Gain Adjustment Range: 4 dB to 59 dB Mic Input to Left/Right Balance Output 79 dB (max gain)Line Input Gain Adjustment Range: -16 dB to 40 dB Line Input to Left/Right Balance Output 60 dB (max gain)Stereo 5/6 1/4" Gain Adjustment Range: O to +18 dB Stereo 5/6 1/4"to Left/Right Output 42 dB (max gain) Stereo 5/6 3.5mm / RCA Gain Adjustment Range: O to +28 dBStereo 5/6 3.5mm / RCA to Left/Right Output: 47 dB (max gain) Stereo 9/10 Gain Adjustment Range: O to +18 dBStereo 9/10 to Left/Right Output 28 dB (max gain)Mic Input to Left/Right Output, Max Input Gain 14 Hz to 25 kHz +0 dB/-1 dB Mic Input to Left/Right Output, input gain 12:00 9.5 Hz to 29 kHz +0 dB/-0.8 dB <0.006% Typical, Mic to Left/Right Output (22 Hz to 22 kHz BW)Output Residual Noise S/N Ratio (Ref: +4dBu) Test ConditionsMaster Left/Right -97 dBu 101 dB Master Fader Down, Channel Levels Down -90 dBu 94 dB Master Fader Nominal, Channel Levels Down -83 dBu 87 dB Master Fade Nominal, Channel Faders Nominal, Panned Odd Channels (left), Even Channels (right)Monitor Send -95 dBu 99 dB All controls o -80 dBu 84 dB All channel sends nominal, masters nominal (Hum and noise measurements: 22 Hz to 22 kHz BW)-128 dBu (input terminated with 150 ohms, bandwidth 20 kHz)
Crosstalk/AttenuationDimensionsMetersWeightSignal/Overload IndicatorsPower RequirementsCommon Mode Rejection Ratio (Mic Input) Adjacent Input Channels (1 kHz) >90 dB Mute Button Attenuation (1 kHz) >90 dB Left to Right Outputs (1 kHz) >70 dB Channel Fader Kill (1 kHz) >85 dB 12.75" wide x 15.1" deep x 2.1875" high (32.39 cm x 38.35 cm x 5.56 cm) PV10BT: 8.22 lbs (3.73 kg) 100-240 VAC 50/60 Hz 15 Watts PV10AT: 8.26 lbs (3.75 kg)6 segment, peak reading (0 db = +4 dBu) Red LED lights 5 dB below clipping 50 dB minimum (20 Hz to 20 kHz) 70 dB typical @ 1 kHz
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTYEffective Date: 11/01/2011What This Warranty CoversYour Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.What This Warranty Does Not CoverThe Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) damage occurring during shipment; (3) damage caused by repair or service performed by persons not authorized by Peavey; (4) products on which the serial number has been altered, defaced or removed; (5) products not purchased from an Authorized Peavey Dealer.Who This Warranty ProtectsThis Warranty protects only the original purchaser of the product.How Long This Warranty LastsThe Warranty begins on the date of purchase by the original retail purchaser. The duration of the Warranty is as follows: Product Category Duration Guitars/Basses, Amplifiers, Preamplifiers, Mixers, Electronic Crossovers and Equalizers 2 years *(+ 3 years) Drums 2 years *(+ 1 year) Enclosures 3 years *(+ 2 years) Digital Effect Devices and Keyboards and MIDI Controllers 1 years *(+ 1 year) Microphones 2 years Speaker Components 1 year (incl. Speakers, Baskets, Drivers, Diaphragm Replacement Kits and Passive Crossovers) Tubes and Meters 90 Days Cables Limited Lifetime AmpKit Link, Xport, Rockmaster Series, Strum’n Fun, RetroFire, GT & BT Series Amps 1 year Marvel Jr. Guitar 90 Days [* Denotes additional Warranty period applicable if optional Warranty Registration Card is completed and returned to Peavey by original retail purchaser within 90 days of purchase.]What Peavey Will DoWe will repair or replace (at Peavey’s discretion) products covered by Warranty at no charge for labor or materials. If the product or component must be shipped to Peavey for Warranty service, the consumer must pay initial shipping charges. If the repairs are covered by Warranty, Peavey will pay the return shipping charges.How To Get Warranty Service(1) Take the defective item and your sales receipt or other proof of date of purchase to your Authorized Peavey Dealer or Authorized Peavey Service Center.OR(2) Ship the defective item, prepaid, to Peavey Electronics Corporation, International Service Center, 412 Highway 11 & 80 East, Meridian, MS 39301. Include a detailed description of the problem, together with a copy of your sales receipt or other proof of date of purchase as evidence of Warranty coverage. Also provide a complete return address.Limitation of Implied WarrantiesANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.Some states do not allow limitations on how long an implied Warranty lasts, so the above limitation may not apply to you.Exclusions of DamagesPEAVEY’S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT, AT PEAVEY’S OPTION. IF WE ELECT TO REPLACE THE PRODUCT, THE REPLACEMENT MAY BE A RECONDITIONED UNIT. PEAVEY SHALL NOT BE LIABLE FOR DAMAGES BASED ON INCONVENIENCE, LOSS OF USE, LOST PROFITS, LOST SAVINGS, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE, OR ANY OTHER DAMAGES WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.If you have any questions about this Warranty or services received or if you need assistance in locating an Authorized Service Center, please contact the Peavey International Service Center at (601) 483-5365.Features and specifications are subject to change without notice.Logo referenced in Directive 2002/96/EC Annex IV(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005The bar is the symbol for marking of new waste and is applied only to equipment manufactured after13 August 2005
U.S. CUSTOMER WARRANTY REGISTRATION Optional Product Extended Warranty RegistrationGive us some information and put your extended warranty into effect!9. How would you describe your level of musicianship/technical expertise?1. First Name Initial Last Name Street Address City State/Province Postal Code( ) Telephone Number E-mail Address( ) - -Fax Number Date of birth 2. Model Serial # Date of Purchase Price Paid3. Name of store where purchased City State4. Top two (2) reasons why you purchased from this store/dealer:8. Which other brands/models did you consider?❒ Past favorable experience❒ Best price❒ Advertised special❒ Convenient location❒ Received as a gift❒ Other❒ Availability of product❒ Friend/Relative’s recommendation❒ Store credit card❒ Knowledgeable staff❒ Availability of lessons❒ Technical instruction6. What two (2) factors most influenced your purchase of this product?❒ Peavey brand name ❒ Craftsmanship❒ Features for price❒ Bundled accessories❒ Sound quality❒ Product appearance❒ Durability❒ Prior experience with Peavey❒ Packaging❒ Other ❒ Beginner - Never played or taken less than one (1) year of lessons❒ Intermediate - One (1) to five (5) years of lessons or playing❒ Advanced - More than five (5) years of lessons or playing; play professionally10. Education: (select best answer)❒ High school❒ Some college❒ Completed college❒ Graduate schoolGender ❒ M ❒ F 11. Which best describe your family income? (select best answer)12. Which of the following is your primary source of information on musical products: (select best answer)Please take a few minutes to fill out this information/survey sheet to help us get to know and serve you better. To save time, submit your warranty registration online at www.peavey.com/support/warrantyregistration❒ Under $15,000 ❒ $15,000 - $24,999❒ $25,000 - $34,999❒ $35,000 - $49,999❒ $50,000 - $74,999❒ Television ❒ Radio❒ Internet❒ Newspaper❒ Magazines❒ Mail order catalogs❒ Direct mail❒ Literature from manufacturer❒ Other❒ $75,000 - $99,999❒ $100,000 - $149,999❒ Over - $150,00013. What is your main motivation for buying new equipment?❒ Replacing old product ❒ Want new and leading edge equipment❒ Fullfill a specific need❒ Supplement existing products❒ Value❒ Impulse❒ Need for improved performance❒ New technology❒ Availability of product❒ Other 7. How did you learn about this Peavey product? (select best answer)❒ Magazine review ❒ Newspaper review❒ Radio advertisement ❒ Advertised special❒ Friend/Relative’s recommendation❒ Salesperson’s recommendation❒ Teacher’s recommendation❒ Catalog or flyer❒ Saw in store❒ Use by professional❒ Other15. In your opinion, what could Peavey do to improve its products and/or service? Please use the space below to tell us your answer.Thank you for taking the time to fill out our survey! Don’t forget to fold and tape (with Peavey address facing out), affix postage stamp and drop in the mail!5. Where do you most often shop for music and sound products?❒ Independent retailer❒ Mass market retailer❒ Mail order magazines❒ Newspaper ads❒ Internet/Web sites❒ OtherRevised 1/1114. Please list your three most frequently visited Web sites.1. http://__________________________________________2. http://__________________________________________3. http://__________________________________________Logo referenced in Directive 2002/96/EC Annex IV(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005The bar is the symbol for marking of new waste and is applied only to equipment manufactured after13 August 2005

Navigation menu