Pelco Dd08 Intercept Dome C290M A 6 99 Users Manual Series Fixed Mount_manual

C290M-A (699) to the manual b382e18a-3cb0-4047-8020-7f2bbd943dac

2015-02-02

: Pelco Pelco-Dd08-Intercept-Dome-C290M-A-6-99-Users-Manual-441235 pelco-dd08-intercept-dome-c290m-a-6-99-users-manual-441235 pelco pdf

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

DD08 Intercept Dome
Series Fixed mount

Installation/Operation Manual
C290M-A (6/99)

PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981
FAX (800) 289-9150 or (1-559) 292-3827

TABLE OF CONTENTS
Section

Page

1.0

WARNINGS ........................................................................................................................................1

2.0

SCOPE ...............................................................................................................................................2

3.0

DESCRIPTION ................................................................................................................................... 2
3.1 MODELS .................................................................................................................................. 2
3.2 CERTIFICATIONS .................................................................................................................... 2

4.0

INSTALLATION .................................................................................................................................. 3
4.1 FIXED MOUNT INSTALLATION AND REMOVAL ....................................................................3
4.1.1 Installing Fixed Mount .................................................................................................. 3
4.1.2 Removing Fixed Mount ................................................................................................ 5
4.2 LENS WIRING .......................................................................................................................... 6
4.3 CAMERA/LENS INSTALLATION .............................................................................................. 6

5.0

ADJUSTMENTS .................................................................................................................................6
5.1 OPERATION ............................................................................................................................. 6

6.0

CARE AND MAINTENANCE .............................................................................................................. 7

7.0

SPECIFICATIONS .............................................................................................................................. 7

8.0

EXPLODED ASSEMBLY DIAGRAM .................................................................................................. 8
8.1 MECHANICAL PARTS LIST ..................................................................................................... 9
8.2 ASSOCIATED HARDWARE ..................................................................................................... 9

9.0

WARRANTY AND RETURN INFORMATION ................................................................................... 10
LIST OF ILLUSTRATIONS

Figure
1
2
3
4
5
6
7
8
9

Page
Back Box Power Switch Location .................................................................................................... 4
Removing Safety Pins ..................................................................................................................... 4
Removing/Attaching Dome to Fixed Mount ..................................................................................... 4
Installing Fixed Mount ..................................................................................................................... 4
Guide Pin/Latch Locations .............................................................................................................. 5
Fixed Mount/Back Box Electrical Interconnect ................................................................................ 5
Locking Fixed Mount in Place ......................................................................................................... 6
Bezel Attachment ............................................................................................................................ 7
DD08 Fixed Mount Exploded Assembly Diagram ........................................................................... 8

REVISION HISTORY
Manual

Date

Comment

C290M
C290M-A

—
6/95
6/99

Original version.
Rev. A. Revised to show rocker style power switch.
Added Section 3.2, Certifications.

®PELCO and the PELCO logo are registered trademarks of PELCO.
©Copyright 1995, PELCO. All rights reserved.
12
ii

PELCO Manual C290M-A (6/99)

INSTALLATION/OPERATION MANUAL
DD08 INTERCEPT DOME SERIES
FIXED MOUNT

1.0 WARNINGS
Prior to installation and use of this product, the following
WARNINGS should be observed.
1.

Installation and servicing should only be done by
qualified service personnel and conform to all local
codes.

Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be
installed where exposed to rain and moisture.

Only use replacement parts recommended by
PELCO.

After replacement/repair of this unit’s electrical
components, conduct a resistance measurement
between line and exposed parts to verify the exposed
parts have not been connected to line circuitry.

The installation method and materials should be
capable of supporting four times the weight of the
enclosure, pan/tilt, camera and lens combination.

The product bears the following marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.

This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.

CAUTION:
TO REDUCE THE RISK OF ELECTRICAL
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.

Please thoroughly familiarize yourself with the information in this manual
prior to installation and operation.
PELCO Manual C290M-A (6/99)

2.0 SCOPE

3.1 MODELS

The information contained in this manual covers the
DD08 Series fixed mount for the IDS08 Series Intercept
Domes.

The model designator is DD08XXX, where each “X”
represents a feature that is essential for operation.

This manual pertains only to the fixed mount. Proceed with installation of the fixed mount and the
camera/lens once back box installation has been
completed.

Example: DD08 E 3 0 Dome drive with SL and
presets, variable pan speed,
and black opaque dome
with smoked window

3.0 DESCRIPTION
The IDS08 Intercept Series of domes allow you to
select any combination of available features to create a
custom dome system. This integral system includes
fixed mount or dome drive (pan/tilt), Coaxitron
receiver/driver and factory installed camera/lens package.
To facilitate this, we use a building-block approach in
assembling the desired components to fulfill the job
requirements. The blocks are broken into four sections.
They are:
1
2
3
4

Dome Drive (DD08)
Dome Receiver/Driver (DRD08)
Back Box (BB08)
Imager/Optics Package (IOP08)

Model Dome Drive
DD08 A = Fixed
mount
B = 355°
C = 360° SL
D = 355° &
Presets
E = SL &
Presets

Dome
Dome
Pan Speed
Color
0 = None
0 = Blk
1 = 12°/sec
opaque
2 = 24°/sec
with
3 = Variable*
smoked
window
1 = Blk
opaque
with
clear
window
2 = Chrome
3 = Gold

* 0 to >200°/sec

3.2 CERTIFICATIONS
The dome system is shipped in two separate boxes:
1 box

containing the Back Box

1 box

containing the Dome Drive, Dome, Dome
Receiver/Driver (when ordered) and Imager/
Optics Package (factory assembled)

DD08A00
DD08B10
DD08B11
DD08B20
DD08B21
DD08C20
DD08C21
DD08C30
DD08D11
DD08D20
DD08E30
DD08E31

UL
X
X
X
X
X
X
X
X
X
X
X
X

CE
X
X
X
X
X
X
X
X
X
X
X

PELCO Manual C290M-A (6/99)

4.0 INSTALLATION

4.1.1 INSTALLING FIXED MOUNT

4.1 FIXED MOUNT INSTALLATION AND
REMOVAL

To install the fixed mount:
1.

Turn off back box power switch, if applicable to
your back box. (See Figure 1 for switch location.)

Remove the hairpin style safety pins from the two
latches in the back box (see Figure 2).

Remove dome from fixed mount. This is only a
pull apart procedure (refer to Figure 3.)

Grasp the fixed mount with two hands as shown in
Figure 4.

While lifting the unit up into the back box, find the
two (2) V-opening latches and two (2) guide pins
at the rear of the back box (see Figure 5).

CAUTION
Switch the rocker style power switch
in back box to the OFF position before installing or removing fixed
mount.

No wiring interface is required between the back box
and the fixed mount. All wiring connections are
achieved when the mechanical connection of the
fixed mount is made.
Ensure the fixed mount will interface electrically with
the back box you have chosen to use. Refer to the back
box manual, C456M, if necessary.

NOTE: Ensure that you install the fixed mount
in correct rotation to the back box so that the
electrical connector on top of fixed mount lines
up with mating connector in back box (see Figure 6).
6.

Upon locating the guide pins, wiggle the unit back
and forth to ensure the guide pins are aligned with
the two (2) Delrin bushings on the fixed mount. At
that instant, push the mount up until the two (2) Vshaped latches engage and lock the mount in place
(see Figure 7). Be sure the latches are completely
closed by pulling down on the latch arm as a check.

Insert the two hairpin style safety pins previously
removed in step 2 into the latches to prevent inadvertent release of fixed mount from the back box.

Install camera/lens of choice, positioning onto
mount with sufficient clearance for dome attachment.

Remove lens cap.

10. Install dome onto fixed mount (refer to Figure 3),
aligning window slot of dome with lens.
NOTE: The fixed mount may also be installed/removed (or bicycled) with the camera/
lens already installed on mount, if needed.

PELCO Manual C290M-A (6/99)

Figure 1. Back Box Power Switch Location

Figure 3. Removing/Attaching Dome to Fixed
Mount

Figure 2. Removing Safety Pins

Figure 4. Installing Fixed Mount

PELCO Manual C290M-A (6/99)

4.1.2 REMOVING FIXED MOUNT
To remove the fixed mount:

L = Latch
P = Pin

Remove the back box bezel/trim ring as described
in back box manual, C456M, and the dome.

Turn off back box power switch, if applicable to
your model (see Figure 1).

Remove the two hairpin style safety pins from the
back box latches (see Figure 2).

Open only one of the latches by pressing the latch
arm with your finger.

Grasp the unit with one hand to prepare for the 510 lb (2.27-4.54 kg) load. Now press open the other
latch with your other hand and lower the fixed
mount.
NOTE: When handling the mount please treat
it with care for there are components that could
possibly bend or be damaged.

Figure 5. Guide Pin/Latch Locations

Fixed Mount Electrical Connector

Back Box Mating Connector

Figure 6. Fixed Mount/Back Box Electrical Interconnect
PELCO Manual C290M-A (6/99)

5.0 ADJUSTMENTS
To adjust the horizontal and vertical position of the
fixed mount perform the following steps:

Figure 7. Locking Fixed Mount in Place
4.2 LENS WIRING
Refer to back box manual, C456M, for wiring pinouts
and wire lens according to manufacturers instructions .
4.3 CAMERA/LENS INSTALLATION
Install the camera/lens you have selected for use with
the IDS08 series dome as follows:
1.

Attach camera/lens to the tilt table using the 1/420 x 1/2" fastener (supplied), mounting through
the tilt table into the camera. Only snug the fastener at this time to allow for camera/lens positioning.

Connect camera power spade lugs and coax video
cable.

Ensure there is sufficient initial clearance between
the camera/lens and dome as you carefully attach
dome to fixed mount. Align the two (2) ball studs
on the dome to the two (2) ball stud receivers on
the fixed mount and push dome until a snapping
sound occurs (refer to Figure 3).

Position camera/lens and route wiring as necessary to achieve clearances. This procedure may require removing and reattaching dome a few times
to obtain correct position.

After satisfactory clearances have been achieved,
remove dome and tighten camera/lens fastener.

Remove dome as per instructions in Section 4.1.1,
step 3.

Loosen the horizontal positioning lock-down knob;
then rotate mount to the desired position and retighten knob.

Loosen the vertical positioning lock-down knob
and adjust tilt table to desired position; then retighten knob.

Attach the dome to the drive as described in Section 4.3, step 3, Camera/Lens Installation.

5.1 OPERATION
Upon completion of the fixed mount and camera/lens
installation and positioning adjustments of the fixed
mount, the Intercept Dome is ready for operation.
Reach into the back box and turn the power switch ON
(if applicable to your back box).

CAUTION
The fixed mount should never be installed
or removed when power switch is in the
ON position.

Now attach the bezel or trim ring to the back box as
shown in Figure 8. Align the three bezel pins with the
large hole in the back box brackets; push the bezel up
and rotate clockwise to latch.
Installation of your Intercept Dome is now complete
and dome is ready for operation.

PELCO Manual C290M-A (6/99)

7.0 SPECIFICATIONS
MECHANICAL
Pan:

360° movement in horizontal plane

Tilt:

-90° movement from horizontal
plane

Approximate
Camera/Lens
Size:

Figure 8. Bezel Attachment

6.0 CARE AND MAINTENANCE
Regularly scheduled maintenance will prolong the operational life and appearance of the equipment.

Connectors
Video:

BNC

Camera Power:

Spade lugs

GENERAL
Construction
Fixed Mount:

IMPORTANT
The acrylic dome is an optical surface.
When cleaning the inner surface of the
dome and viewing window, treat as carefully as you would a fine camera lens.

Lower Dome:

Aluminum with stainless steel
hardware
Acrylic hemisphere available in
the following types:
Black opaque with smoked window (1 f-stop light loss)

Do not use liquid of any kind on
coated inner surface of dome.

If dust or other debris accumulates on the inside of the
lower dome, remove with clean air pressure only. Compressed air cans are available from commercial photographic equipment and supply dealers.

Maximum total length of camera/
lens 6.50" (16.5 cm), including
BNC cable connection to camera;
max. lens width 4.50" (11.4 cm);
max. lens height 3.25" (8.25 cm)

Black opaque with clear window
(virtually zero light loss)
Chrome or Gold (2 f-stop light
loss)
Weight:

2 lbs 4.8 oz. (1.04 kg).

Clean the outer surface of the dome and the inner
surface of the viewing window with a non-abrasive cleaning cloth and anti-static cleaner that is safe for
use on acrylic plastic. Do not use kerosene or similar
substances that can scratch the surface.

PELCO Manual C290M-A (6/99)

8.0 EXPLODED ASSEMBLY DIAGRAM

Figure 9. DD08 Fixed Mount Exploded Assembly Diagram

PELCO Manual C290M-A (6/99)

8.1 MECHANICAL PARTS LIST
The following parts list corresponds to the exploded assembly diagram in Figure 9.
Item No.
1
2
3
4
5
6
7
8
9

Quantity
2
2
1
1
1
1
1
2
1

10
11
12
13

2
2
2
6

Description
Bushing, delrin 3/8" ID x 5/8" OD
Push nut, .625" OD
Bracket, drive mount, upper
Connector, receptacle, 25 position
Bracket, spindle, fixed mount
Tilt table, fixed mount
Frame 8", fixed mount
Pin, latch, dome drive
Dome, 8-1/2", acrylic
Black opaque w/smoked viewing window
Black opaque w/clear viewing window
Chrome finish f/2
Gold finish f/2
Ball stud
Knob, grey, 1/4-20 tapped
Receiver, ball stud
Pin, crimp, loose piece (not shown)
(for use with item #4)
Connector, BNC, crimp, for RG174 coax
(not shown)

Part Number
80010004
80010011
8004034COMP
CON10J025Z41T
8004037COMP
8004021COMP
8004022COMP
8004145COMP
80810011-0
80810011-1
80810011-2
80810011-3
PT180410000
CM1610003
PT180410001
CON66107-2
CONCPM88-174

8.2 ASSOCIATED HARDWARE
Item No.
A
B
C
D
E
F
G
H
I
J
K
L

Quantity
2
1
1
2
4
2
4
4
2
2
1
1

PELCO Manual C290M-A (6/99)

Description
Screw 1/4-20 x 1" flat hd phil, SS
Screw 1/4-20 x 1" soc hd c/s,SS
Nut, lock, hex, 1/4-20, nylon insert, SS
Screw 6-32 x 3/8" pan hd phil, SS
Washer, internal star #6, SS
Screw 6-32 x 1/2" pan hd phil, SS
Screw 8-32 x 1/2" pan hd phil, SS
Washer, internal star #8, SS
Screw 6-32 x 3/8" flat hd phil, black oxide
Spacer, 1/4" hex x 1/2" L, 6-32 tapped
Washer, fender, 1/4 x 1.5 x 14 ga, black oxide
Washer, split lock, 1/4" SS

Part Number
ZH1/420X1.00SFS
ZH1/420X1.00SS
ZH1/420NUTCHN
ZH6-32X.375SPP
ZH6LWSIS
ZH6-32X.500SPP
ZH8-32X.500SPP
ZH8LWSIS
ZH6-32X.375BPF
SPA8423
ZH255X1.50X62
ZH1/4LWSSL

9.0 WARRANTY AND RETURN
INFORMATION

WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material
or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex® Series products (multiplexers, server, and keyboard).
• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera
models, which have a five-year warranty.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.months on DX
Series digital video recorders, NVR300 Series network video recorders, Endura™ Series
distributed network-based video products, and TW3000 Series twisted pair transmission
products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or
accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting
from the specific use or application made of the Products. Pelco’s liability for any claim,
whether based on breach of contract, negligence, infringement of any rights of any party
or product liability, relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special, incidental or
consequential damages (including loss of use, loss of profit and claims of third parties)
however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also
have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Method of return shipment shall be the same or equal to the method by which the item
was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory
at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods
to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933

PELCO Manual C290M-A (6/99)

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
XMP Toolkit                     : 3.1-702
About                           : uuid:95346a3e-ba94-11da-8136-000a95a25184
Producer                        : Acrobat Distiller 3.01 for Power Macintosh
Keywords                        : Camera Site Equipment|Camera Systems|Intercept
Create Date                     : 1999:06:21 10:10:29Z
Modify Date                     : 2006:04:04 08:25:54-07:00
Metadata Date                   : 2006:04:04 08:25:54-07:00
Creator Tool                    : Adobe PageMaker 6.52
Document ID                     : uuid:8f4da303-ba94-11da-8136-000a95a25184
Instance ID                     : uuid:826ae1ab-f6d7-4b9e-be59-aa7f77deaba4
Format                          : application/pdf
Creator                         : KSlaughter
Title                           : Pelco DD08 Intercept Dome Series Fixed Mount_manual
Subject                         : Camera Site Equipment|Mounts and Adapters|Dome Mounts
Description                     : Obsolete
Page Count                      : 12
Author                          : KSlaughter

EXIF Metadata provided by EXIF.tools

Pelco Dd08 Intercept Dome C290M A 6 99 Users Manual Series Fixed Mount_manual

C290M-A (699) to the manual b382e18a-3cb0-4047-8020-7f2bbd943dac

Navigation menu

Versions of this User Manual:

Views

Navigation