Pelican Accessories G3-2 G3 Wireless Controller User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	303618
Application ID	Z1wKHklp8h3uJ60iprRGZg==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.27kB (65916 bits)
Date Submitted	2003-02-18 00:00:00
Date Available	2003-02-12 00:00:00
Creation Date	0000-00-00 00:00:00
Document Lastmod	0000-00-00 00:00:00
Document Title	Manual

LIMITED WARRANTY
Pelican Accessories warrants to the original consumer purchaser that
the product will be free from defects in materials and / or workmanship
for a period of 120 days from the date of purchase. If a defect covered
by this warranty occurs during this period, Pelican Accessories at its
option will repair or replace, at no charge, any part that Pelican Accessories
determines to be defective.
To obtain warranty service during the warranty period, send the defective
product postage pre-paid, with a money order for $4.00 to cover the
return postage and handling, along with proof of purchase and the date
of purchase to:
Wireless with Rumble
Gamer ’s Guarantee
Our products are developed, tested, and approved by gamers for
gamers. Pelican’s Gamer’s Guarantee states: If you are not 100%
satisfied with your new G3 Wireless controller we will replace it
or replace it with an equal valued item.
PELICAN ACCESSORIES
1840 East 27th Street
Vernon, CA 90058
This warranty shall not apply if the product has been damaged by abuse,
misuses, negligence, accident, modification, tampering or by any other
causes unrelated to defective materials and / or workmanship.
Repair or replacement as provided under this warranty is Pelican
Accessories' exclusive prerogative. ANY APPLICABLE IMPLIED
WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE HERBY LIMITED
TO 120 DAYS FROM THE DATE OF PURCHASE AN ARE SUBJECT
TO THE CONDITIONS SET FORTH IN THIS LIMITED WARRANTY. IN
NO EVENT SHALL PELICAN ACCESSORIES OR INCIDENTAL
DAMAGES RESULT FROM THE BREACH OF ANY EXPRESS OR
IMPLIED WARRANTIES. This warranty gives you specific legal rights,
and you may also have other legal rights,
Which vary from state to state.
Changes or modifications not expressly approved by the manufacture could void the
user's authority to operate the equipment. This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions; (1) this device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For technical questions please visit
http://www.pelicanacc.com
or call us directly at 1-800-331-3844
Pelican and its logo are registered trademarks.
GameCube™ is a registered trademark of
Nintendo of America, Inc.
This product is not desgined, manufactured, sponsored
or endorsed by Nintendo of America, Inc.
Instruction for Operation:
G3 Wireless Controller
Left & Right Triggers
Signal LED
(Yellow)
SIGNAL
Turbo Button
Channel Switch
CHANNEL
Analog
Stick
Action
Buttons
1 2 3 4
OFF ON RUMBLE
OFF
Start/
Pause
START / PAUSE
Analog
Stick
BAND
A B
A/B Band
Switch
D-Pad
Power On/Off-rumble Off Switch
G3 Wireless Receiver
Link LED (Green)
Signal LED (Yellow)
SIGNAL
Power LED (Red)
POWER
Channel Switch
Band Switch
BAND
B A
PL-7008
PRODUCT OVERVIEW:
G3 Wireless Controller uses advance technology which gives you the ability to play without the
limitations of a typical corded controller, hence there are a few switches and LED (lights) not
found on your basic GameCube™ Controller.
Channel Switch (Receiver and Controller):
This switch selects the broadcast channel of the radio frequency. There are four positions;
1, 2, 3 and 4. There is a corresponding Channel Switch on the receiver
Band Switch (Receiver and Controller):
This switch selects the bandwidth. There are two positions; A and B. There is a corresponding
Band Switch on the receiver
Power Switch (Controller):
This switch selects the power mode. There are 3 positions; Off, On, and Rumble Off
Signal LED (Yellow, Receiver and Controller):
When on or flickering data is being transmitted between Controller and Receiver
Power LED (Red, Receiver):
When on indicates Receiver is operating correctly
Link LED (Green, Receiver):
When on indicates Controller and Receiver are linked and communicating. If flickering the
Controller and Receiver are not communicating
INSTRUCTIONS:
1. Insert Batteries:
Remove the battery lid and place the two AA batteries (included) into the G3 Wireless
Controller. Make sure they are inserted as shown in the battery compartment. The batteries
included are not long life.
2. Plug in the Receiver:
With the GameCube™ turned off, plug the receiver into controller port one (far left port.)
3. Check Band setting:
Confirm that the Band Switch is set to A on both the controller and the receiver.
Note: the only time you would ever change this switch is if you experienced a drop off in the
signal, causing game play to be suspended. If this happens repeatedly we suggest
you switch to Band B on both the Controller and Receiver.
4. Select a Channel on the Controller:
You may select any channel you desire 1, 2, 3 or 4.
5. Select a Channel on the Receiver:
This must match the channel selected on the Controller.
Note: If using more then one controller you must use different channel settings, i.e., the first
controller and receiver are set to Channel 1, the second controller and receiver are
set to Channel 2. The channel position selected on the G3 Controller and Receiver
have no relation to the GameCube™ controller ports.
6. Turn on the Controller:
Move the Power Switch to On, the signal LED will light.
Note: If you wish to extend battery life select the Rumble Off position. This will turn off the
rumble effect in game play resulting in a doubling of your battery life.
OTHER FEATURES:
Multiple Players:
You may play with up to four G3 Wireless controllers. Check to see that the channel switches
are set as outlined above.
Power Save Mode:
When not in use the G3 controller automatically goes into a sleep mode to conserve
batteries. A touch of any button puts the controller back into play mode.
Note: Turn off the controller when not in use to extend your battery life.
Turbo Function:
This feature allows rapid fire of any selected fire button. To turn on, press the Turbo button,
and then while still holding down the Turbo button press the fire button that you wish to have
the Turbo feature. To return the button back to a normal fire button repeat the above process
or turn on and off the controller.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 1

EXIF Metadata provided by EXIF.tools