Pentair Aquatic Systems RF2000 RF2000 Transmitter User Manual RF2000

Pentair Aquatic Systems RF2000 Transmitter RF2000

Manual

Rev X1 Pentair Pool Products, Inc. P/N 840316Sanford NCMoorpark CAINSTRUCTIONSRF2000 Transmitter and ReceiverThis equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules.  These limits are designed to providereasonable protection against harmful interference in a residential installation.  Thisequipment generates, uses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radiocommunications.  However, there is no guarantee that interference will not occur in aparticular installation.  If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the followingmeasures:--  Reorient or relocate the receiving antenna.--  Increase the separation between the equipment and receiver.--  Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.--  Consult the dealer or an experienced radio/TV technician for help.Modifications not expressly approved by the party responsible for FCC compliance couldvoid the user's authority to operate the equipment.Installation Instructions1.  Set the local address code in the receiver by switching dipswitches 5 and 6 inside ofthe receiver.  The default channel is Channel 1.1. Turn power switch and colorwheel switch on the side of the PG2000 unit to OFF.2. Remove PG2000 body.3. Very Carefully straighten out the antenna on the receiver module.4. Place receiver module on the left side of the unit next to the ballast.  Look for the ribsas a guide.  The 4 pin plug should face the back of the unit and the antenna should faceforward.  Use the double sided foam tape to hold the receiver in place5. Plug the 4 pin connector from the PG2000 into the 4 pin connector from the RF2000.The plug coming out of the RF2000 basically does a U turn and heads toward thePG2000 plug.  You may have to shift the receiver module around a bit to get your handsin to make the connection6.  Drape the antenna forward  into the fiber conduit area.  It should stay on the outerperimeter of this area curving around to the front of unit.  Keep the antenna as straight aspossible.
Rev X1 Pentair Pool Products, Inc. P/N 840316Sanford NCMoorpark CA7.  Make sure the receiver module will clear the body and the entire antenna remainsinside of the PG2000 housing.8. Replace the PG2000 body9. Switch power switch to RF2000 position.  The colorwheel switch remains in theoff/RF2000 position.10. Install the 9V battery in the transmitter.Operating instructions1. The 4 buttons along the top of the transmitter are the channel buttons.  Depress theappropriate channel you would like to operate.  The channel button is activated if it is inthe depressed position.  The default setting in all receivers in channel 1.2.  To turn on the unit press the “power on” function button.  The beeping sound indicatesthat a signal is being sent.  Hold down the button until the unit turns on.  This shouldhappen immediately but there may not be a visible indicator since the bulb must firstwarm up.  The transmitter will only send a signal for 5 seconds as indicated by thebeeping.3.  To turn on the colorwheel press the “color on” function button.  The beeping soundindicates that the signal is being sent.  There is a 1/2 second delay once it has received thesignal.4. To freeze on a color simply press the “color off” function button.  If you turn thepower off, it will also shut off the colorwheel.5. If the unit is cycled off then on it may take up to 3-4 minutes for the lamp to “restrike”or come back on.  All metal halide lamps have this characteristic and this is a normalfunction of the PG2000.

Navigation menu