Pentair Aquatic Systems RF2000 RF2000 Transmitter User Manual RF2000

Download:
Mirror Download [FCC.gov]
Document ID	220067
Application ID	NiyTLrKcVdolMpojwiUV/w==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	0.44kB (5553 bits)
Date Submitted	2002-01-10 00:00:00
Date Available	2002-01-10 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Acrobat PDFWriter 3.02 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	RF2000.PDF
Document Creator	Microsoft Word
Document Author:	D. Dunn

INSTRUCTIONS
RF2000 Transmitter and Receiver
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the party responsible for FCC compliance could
void the user's authority to operate the equipment.
Installation Instructions
1. Set the local address code in the receiver by switching dipswitches 5 and 6 inside of
the receiver. The default channel is Channel 1.
1. Turn power switch and colorwheel switch on the side of the PG2000 unit to OFF.
2. Remove PG2000 body.
3. Very Carefully straighten out the antenna on the receiver module.
4. Place receiver module on the left side of the unit next to the ballast. Look for the ribs
as a guide. The 4 pin plug should face the back of the unit and the antenna should face
forward. Use the double sided foam tape to hold the receiver in place
5. Plug the 4 pin connector from the PG2000 into the 4 pin connector from the RF2000.
The plug coming out of the RF2000 basically does a U turn and heads toward the
PG2000 plug. You may have to shift the receiver module around a bit to get your hands
in to make the connection
6. Drape the antenna forward into the fiber conduit area. It should stay on the outer
perimeter of this area curving around to the front of unit. Keep the antenna as straight as
possible.
Rev X1
Pentair Pool Products, Inc.
Sanford NC
Moorpark CA
P/N 840316
7. Make sure the receiver module will clear the body and the entire antenna remains
inside of the PG2000 housing.
8. Replace the PG2000 body
9. Switch power switch to RF2000 position. The colorwheel switch remains in the
off/RF2000 position.
10. Install the 9V battery in the transmitter.
Operating instructions
1. The 4 buttons along the top of the transmitter are the channel buttons. Depress the
appropriate channel you would like to operate. The channel button is activated if it is in
the depressed position. The default setting in all receivers in channel 1.
2. To turn on the unit press the “power on” function button. The beeping sound indicates
that a signal is being sent. Hold down the button until the unit turns on. This should
happen immediately but there may not be a visible indicator since the bulb must first
warm up. The transmitter will only send a signal for 5 seconds as indicated by the
beeping.
3. To turn on the colorwheel press the “color on” function button. The beeping sound
indicates that the signal is being sent. There is a 1/2 second delay once it has received the
signal.
4. To freeze on a color simply press the “color off” function button. If you turn the
power off, it will also shut off the colorwheel.
5. If the unit is cycled off then on it may take up to 3-4 minutes for the lamp to “restrike”
or come back on. All metal halide lamps have this characteristic and this is a normal
function of the PG2000.
Rev X1
Pentair Pool Products, Inc.
Sanford NC
Moorpark CA
P/N 840316

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Creator                         : Microsoft Word
Create Date                     : Friday, December 21, 2001 5:30:04 PM
Title                           : RF2000.PDF
Author                          : D. Dunn
Producer                        : Acrobat PDFWriter 3.02 for Windows
Subject                         : 

EXIF Metadata provided by EXIF.tools