Pet Mate 355356 Elite Super Selective Cat Flap User Manual Layout 1

Pet Mate Ltd Elite Super Selective Cat Flap Layout 1

User Manual

ENGLISHDEUTSCHFRANÇAISESPAÑOLNEDERLANDSIMPORTANT - READ BEFORE USEFITTING INSTRUCTIONSWICHTIG - BITTE VOR VERWENDUNG LESENEINBAUANLEITUNGIMPORTANT - À LIRE AVANT USAGEINSTRUCTIONS DE MONTAGEIMPORTANTE - LEA ANTES DE USARINSTRUCCIONES DE INSTALACIÓNBELANGRIJK! DIT EERST LEZEN VOOR GEBRUIKMONTAGE INSTRUCTIESCAT MATE Elite®NLEFDCAT FLAP · KATZENKLAPPE · CHATIÈRE · GATERA · KATTENDEUR©PET MATE Ltd ·Lyon Road · Hersham · Surrey · KT12 3PU · EnglandN.America only:Ani Mate ·104A LongviewDrive·Conroe · Texas 77301www.pet-mate.com 30512/0312Ref: 305N · 306 · 307 · 355 · 356www.pet-mate.com+44 (0)1932 700 001NAmerica (936) 760 433330512-0312 instructions.qxd 9/3/12 14:42 Page 1
ENGLISHDEUTSCHFRANÇAISESPAÑOLNEDERLANDS321 25 69 103 4711 128150mm(6”)3mm(1/8”) tA30512-0312 instructions.qxd 9/3/12 14:42 Page 3
ENGLISH42.3 The black foam seal is not suitable for fitting to glass and shouldbe removed. If desired, the exterior frame may be sealed to theglass panel using silicone sealant.2.4 Position interior frame on inside of door, screw exterior frame toit by using appropriate screws for panel thickness, (t), as shown inFig. 6. If necessary, cut supplied screws to length. Finally fit twoscrew caps.3. Wall FittingIf you are installing your cat flap in a wall, you will need to purchaseElite wall liners. You will need 1 wall liner for every 50mm (2") of wallthickness over 50mm (2") or 100mm (4”) for ‘Chip & Disc’ (Ref.355/356) cat flaps.3.1 Create a rectangular hole in your wall 205mm (8") high by180mm (7") wide.3.2 Remove interior frame battery cover by pushing up as shown, (Fig.7). 4Way Locking Cat Flap (Ref. 307) only: Remove the 4-wayknob as shown in Fig. 12 using a thin screwdriver to lever off cover(A) as shown.3.3 Remove interior frame cover by unscrewing 2 screws in rear ofinterior frame (Fig. 8). (Note: these screws may be discarded asit will be impossible to refit them). Next remove the 2 screwsunder the batterycover and remove the interior frame by pivotingdown (Fig. 9).3.4 Carefully remove 2 screw clips with pliers. (Fig. 10).3.5 Fit interior frame assembled with requisite number of wall liners tointerior wall securing in position with 2 suitable screws as shownin Fig. 11. (Note: you will need to fit a washer (not supplied)under the head of the screws). If required, the wall liners maybe glued in place, although a firmpush fit will usually suffice.3.6 Refit interior frame cover with 2 screws under battery cover,taking great care not to trap electrical wires. (Refit the 4-way knobfor 4Way Locking Cat Flap using a hand screwdriver.) Replacethe batterycover.3.7 Fit exterior frame using 2 off 25mm (1") screws supplied andfinally,fit 2 screw caps.IMPORTANT:• BEFORE INSTALLATION, PROGRAM CAT FLAP AS DESCRIBED INOPERATION INSTRUCTIONS• DO NOT CUT TUNNEL OF CAT FLAPS.1. Wood / Plastic / Metal Door Panels1.1 Place exterior frame in desired position on door and draw aroundthe aperture. We recommend the bottom of the aperture isapproximately 150mm (6") above ground level. (Fig.1). If youmust fit higher consider providing a step to help your cat enter.1.2 Use an electric jigsaw to cut 3mm (1/8") OUTSIDE of drawn line.(Fig. 2). Be careful to cut hole square to the door, particularly withthicker doors. Ensure interior frame is free fitting in hole.1.3 Determine thickness of door panel, (t). (Fig. 3).1.4 Holding the interior frame and the exterior frame in position, markthe 2 screw holes. (Fig. 4).1.5 Remove the frames and drill screw clearance holes in panel to6mm (1/4") diameter. (Fig. 5).1.6 Position interior frame on inside of door and screw exterior frameto it by using appropriate screws for panel thickness, (t), as shownin Fig. 6. If necessary,cut supplied screws to length. Finally fit twoscrew caps.1.7 For metal panels you must remove batteries for a minimum of 2minutes after installation. This will enable the cat flap to retuneitself to its new location for maximum performance.2. Glass Panels 0-50mm (0-2") Thick2.1 We recommend that you ask a glazier to cut a hole of 229mm (9")diameter in the position required and then install the cat flap asdetailed below. Alternatively, you may prefer to replace the glasspanel with a clear plastic panel and install as instructions 1.1 to1.6.Note: It is not possible to cut a hole in double glazed ortoughened glass. You will need a new panel with the holealready cut from your glazier.2.2 Determine thickness of door panel, (t). (Fig. 3).ENGLISH530512-0312 instructions.qxd 9/3/12 14:42 Page 5
FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu