Pet Mate 355356 Elite Super Selective Cat Flap User Manual Layout 1
Pet Mate Ltd Elite Super Selective Cat Flap Layout 1
Pet Mate >
User Manual
9/3/12 14:42 Page 1 ® CAT MATE Elite CAT FLAP · KATZENKLAPPE · CHATIÈRE · GATERA · KATTENDEUR ENGLISH 30512-0312 instructions.qxd IMPORTANT - READ BEFORE USE FITTING INSTRUCTIONS DEUTSCH Ref: 305N · 306 · 307 · 355 · 356 WICHTIG - BITTE VOR VERWENDUNG LESEN IMPORTANT - À LIRE AVANT USAGE INSTRUCTIONS DE MONTAGE FRANÇAIS EINBAUANLEITUNG IMPORTANTE - LEA ANTES DE USAR BELANGRIJK! DIT EERST LEZEN VOOR GEBRUIK MONTAGE INSTRUCTIES © PET MATE Ltd · Lyon Road · Hersham · Surrey · KT12 3PU · England www.pet-mate.com N.America only: Ani Mate · 104A Longview Drive · Conroe · Texas 77301 +44 (0)1932 700 001 www.pet-mate.com 30512/0312 N America (936) 760 4333 NEDERLANDS NL ESPAÑOL INSTRUCCIONES DE INSTALACIÓN 1 9/3/12 14:42 Page 3 3mm (1/8”) ENGLISH 30512-0312 instructions.qxd DEUTSCH 150mm (6”) 10 11 12 NEDERLANDS ESPAÑOL FRANÇAIS 9/3/12 14:42 Page 5 IMPORTANT: ENGLISH • BEFORE INSTALLATION, PROGRAM CAT FLAP AS DESCRIBED IN OPERATION INSTRUCTIONS • DO NOT CUT TUNNEL OF CAT FLAPS. 1. Wood / Plastic / Metal Door Panels 1.1 Place exterior frame in desired position on door and draw around the aperture. We recommend the bottom of the aperture is approximately 150mm (6") above ground level. (Fig.1). If you must fit higher consider providing a step to help your cat enter. 1.2 Use an electric jigsaw to cut 3mm (1/8") OUTSIDE of drawn line. (Fig. 2). Be careful to cut hole square to the door, particularly with thicker doors. Ensure interior frame is free fitting in hole. 1.3 Determine thickness of door panel, (t). (Fig. 3). 1.4 Holding the interior frame and the exterior frame in position, mark the 2 screw holes. (Fig. 4). 1.5 Remove the frames and drill screw clearance holes in panel to 6mm (1/4") diameter. (Fig. 5). 1.6 Position interior frame on inside of door and screw exterior frame to it by using appropriate screws for panel thickness, (t), as shown in Fig. 6. If necessary, cut supplied screws to length. Finally fit two screw caps. 1.7 For metal panels you must remove batteries for a minimum of 2 minutes after installation. This will enable the cat flap to retune itself to its new location for maximum performance. 2. Glass Panels 0-50mm (0-2") Thick 2.1 We recommend that you ask a glazier to cut a hole of 229mm (9") diameter in the position required and then install the cat flap as detailed below. Alternatively, you may prefer to replace the glass panel with a clear plastic panel and install as instructions 1.1 to 1.6. Note: It is not possible to cut a hole in double glazed or toughened glass. You will need a new panel with the hole already cut from your glazier. 2.2 Determine thickness of door panel, (t). (Fig. 3). 2.3 The black foam seal is not suitable for fitting to glass and should be removed. If desired, the exterior frame may be sealed to the glass panel using silicone sealant. 2.4 Position interior frame on inside of door, screw exterior frame to it by using appropriate screws for panel thickness, (t), as shown in Fig. 6. If necessary, cut supplied screws to length. Finally fit two screw caps. ENGLISH 30512-0312 instructions.qxd 3. Wall Fitting If you are installing your cat flap in a wall, you will need to purchase Elite wall liners. You will need 1 wall liner for every 50mm (2") of wall thickness over 50mm (2") or 100mm (4”) for ‘Chip & Disc’ (Ref. 355/356) cat flaps. 3.1 Create a rectangular hole in your wall 205mm (8") high by 180mm (7") wide. 3.2 Remove interior frame battery cover by pushing up as shown, (Fig. 7). 4 Way Locking Cat Flap (Ref. 307) only: Remove the 4-way knob as shown in Fig. 12 using a thin screwdriver to lever off cover (A) as shown. 3.3 Remove interior frame cover by unscrewing 2 screws in rear of interior frame (Fig. 8). (Note: these screws may be discarded as it will be impossible to refit them). Next remove the 2 screws under the battery cover and remove the interior frame by pivoting down (Fig. 9). 3.4 Carefully remove 2 screw clips with pliers. (Fig. 10). 3.5 Fit interior frame assembled with requisite number of wall liners to interior wall securing in position with 2 suitable screws as shown in Fig. 11. (Note: you will need to fit a washer (not supplied) under the head of the screws). If required, the wall liners may be glued in place, although a firm push fit will usually suffice. 3.6 Refit interior frame cover with 2 screws under battery cover, taking great care not to trap electrical wires. (Refit the 4-way knob for 4 Way Locking Cat Flap using a hand screwdriver.) Replace the battery cover. 3.7 Fit exterior frame using 2 off 25mm (1") screws supplied and finally, fit 2 screw caps. FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Create Date : 2012:03:09 14:42:58Z Creator Tool : QuarkXPress(tm) 6.52 Modify Date : 2012:12:24 09:22:17+08:00 Metadata Date : 2012:12:24 09:22:17+08:00 Producer : QuarkXPress(tm) 6.52 X Press Private : %%DocumentProcessColors:.%%EndComments Format : application/pdf Title : Layout 1 Document ID : uuid:0a8f9c1e-917a-41cc-8680-9467e77278d9 Instance ID : uuid:45da1228-3cdd-45e4-96ff-744c9025bc76 Page Count : 4 Creator : QuarkXPress(tm) 6.52EXIF Metadata provided by EXIF.tools