Philio Technology PAD06 Smart Dimmer Socket User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3255710
Application ID	HoOvpVcJu8GiOVY6jFm/qg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.45kB (168113 bits)
Date Submitted	2017-01-12 00:00:00
Date Available	2017-01-12 00:00:00
Creation Date	2017-01-09 11:03:31
Producing Software	LibreOffice 5.0
Document Lastmod	0000-00-00 00:00:00
Document Title	User manual
Document Creator	Writer

PAD06
Join/Leave Network
Zigbee Smart Dimmer Socket
* Join Network without user action
Power on the device, it will enter the find and join network mode.
* Join network with user action
1. Making the zigbee network in the permitting joining mode.
2. Pressed the button of PAD06 three times in two seconds. the PAD06 will
scan and try joining the network.
* Reset to factory default / Leave network
1. Pressed the button three times in two seconds, and do not release the
button in the 4th pressed without 5 seconds.
2. The device will leave the network, and LED will turn on.
Warning: Do not use Non-Dimmable LED lamps.
User Interface
PAD06 is an E27(EU)/ E26(US) Edison screw based lamp socket, based on
* Button Function
Zigbee technology, which provides electrical connection to the E14(EU)/
E12(US) Edison screw based lamps and support it in the lighting fixture. The
use of socket allows lamps to be safely and conveniently replaced. You can
1. Relay Control
On/Off the light by pressing the button briefly, or a long pressing to control
When pressed and released button, the PAD06 will control the relay in
the brightness of dimmable light bulb.
toggling way.
For example, if you press the button then release and the relay is off, the
device will turn the relay on.
See the LED function for more information.
2. Dimmer Control
Programming
When long pressing button, the PAD06 will control the brightness of
dimmable light bulb.
* Zigbee Cluster Library Description
3. Join network
The PAD06 support Profile Home Automation v1.2 (profile is is 0x0104).
When pressed and released button three in 2 seconds, the PAD06 will do
The device is hosted in endpoint 1 (0x01).
finding and joining network.
4. Reset to default / Leave network
* Supported Clusters List
Pressed the button three times in two seconds, and do not release the
button in the 4th pressed without 5 seconds, the PAD06 will do reset to
default.
* LED Function
1. Relay Status
If the relay is on, the device will turn the LED on.
Cluster ID
Cluster Name
0x0000
Basic
0x0004
Group
0x0005
Scenes
0x0006
ON/OFF
0x0008
Level Control
If the relay is off, the device will turn the LED off.
* Basic Cluster (Cluster ID :0x0000)
2. Reset to default / Leave network
Attribute ID
When PAD06 reset to default / leave network the relay will turn on.
0x0500
3. Try joining network
Power on the device, if PAD06 doesn't join network, the device will auto
start the try joining network mode. The LED will light on one second.
Attribute Name
Model identifier
Attribute Type
CHAR
Default Value
* Group Cluster (Cluster ID :0x0004)
* Level Control Cluster (Cluster ID :0x0008)
1. Read Current Level
Request
Request
groupId : 0xABCD (by user)
groupName : 0x00 (by user)
Attrebute ID : 0x0000
Response
Attrebute Data : 0x00(1 byte for current level)
* Scenes Cluster (Cluster ID :0x0005)
Request
2. Level Control
sceneId : 0x01 (by user)
extensionFieldSets : cluster id, length, value
cluster id : scenes to do cluster id.
length : value length.
command id : 0x00
level : 0x00 (by user)
transition time : 0x0000 (by user)
3. Level Control Move Mode
command id : 0x01
movemode : 0x01 (turn on) , 0x00 (turn off)
rate : 0x0A
* ON/OFF Cluster (Cluster ID :0x0006)
1. Read Relay Status
Request
Attrebute ID : 0x0000
4. Level Control Step
Response
command id : 0x02
stepmode : 0x00 (turn on one step) , 0x01 (turn off one step)
setpsize : 0x0A (by user)
transition time : 0x0000 (by user)
Attrebute Data : 0x00(OFF), 0x01(ON)
2. Control Relay
Attrebute Date : 0x00(OFF), 0x01(ON)
5. Level Control Stop
Over The Air (OTA) Firmware Update
command id : 0x03
The device support the Zigbee firmware update via OTA.
Before starting the procedure, please remove the front cover of the
device. Otherwise the hardware check will be failed.
6. Level Control With ON/OFF
command id : 0x04
level : 0x00 (by user)
transition time : 0x0000 (by user)
Choosing a Suitable Location
1. Do not locate the dimmer facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Switch is 0°C~40°C.
7. Level Control Move Mode With ON/OFF
3. Do not locate the dimmer where exists combustible substances or any source of
command id : 0x05
movemode : 0x01 (turn on) , 0x00 (turn off)
rate : 0x0A
heat, e.g. fires, radiators, boiler etc.
4. After putting it into use, the body of dimmer will become a little bit hot of which
phenomenon is normal.
8. Level Control Step With ON/OFF
command id : 0x06
stepmode : 0x00 (turn on one step) , 0x01 (turn off one step)
setpsize : 0x0A (by user)
transition time : 0x0000 (by user)
9. Level Control Stop With ON/OFF
command id : 0x07
Note: In level control cluster, all with on/off command can control PAD06 without
relay on/off, but the eithers command only control when relay on.
screw lamp holder Type:
US TYPE: PAD06-2
Since the socket type for each country in Europe varies, refer to the outline for each
socket suited for each country as follows:
EU TYPE: PAD06-1
Note: Please make sure that the intensity of the screw lampholder of the electrical
device must be Maximum Load (Ampere) and have same head as the enclosed
screw lampholder before inserting to the socket.
Troubleshooting
Specification
Symptom
Cause of Failure
Recommendation
Operating Voltage:
100V~240V / 50Hz~60Hz
The Switch not
1. The Switch is not
1. Check power connections
Maximum Load (watts):
40W (Incandescent bulbs); ( PAD06-1; PAD06-2)
2. Don’t open up the Switch and send it for
Maximum Load (watts):
13W (Dimmable LED bulbs); ( PAD06-1; PAD06-2)
working and LED off
plugged into the
electrical outlet
repair.
Screw lamp holder Type: EU type: E27 to E14; PAD06-1
properly
US type: E26 to E12; PAD06-2
2. The Switch break
down
The Switch LED
1.Check if the load
illuminating, but
plugged into the Switch
cannot control the
has its own ON/OFF
ON/OFF
switch
Switch of the load
1. Set the ON/OFF switch of the load
attached to ON
2. Unprotected the switch or follow the
instruction of protection.
2. The switch is protected
illuminating, but the
Detector cannot
control
1. Not carry out
association
0°C ~ 40°C
Frequency Range:
2405MHz~2475MHz(EU)(US/Canada)(TW/JP)
RF Radiated Power:
+1dBm
Transmission Range:
Minimum 40 m in door 100m outdoor line of sight
Modulation Type:
O-QPSK - Offset - Quadrature Phase Shift Keying
** Specifications are subject to change and improvement without notice.
attached
The Switch LED
Operating Temperature:
FCC ID : RHHPAD06
1. Carry out association
2. Wait for a while to re-try
2. Same frequency
interference
the Switch
Warning: Do not use Non-Dimmable LED lamps.
Warning:
If this equipment does cause harmful interference to radio or television reception, which
1.Plug out to disconnect from power supply; Do not plug in line.
can be determined by turning the equipment off and on, the user is encouraged to try to cor-
2. Do not exceed the max rating.
rect the interference by one of the following measures:
3. Do not use Non-Dimmable LED lamps.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Disposal
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
This marking indicates that this product should not be disposed with
connected.
other household wastes throughout the EU. To prevent possible harm to
• Consult the dealer or an experienced radio/TV technician for help.
the environment or human health from uncontrolled waste disposal,
This device complies with Part 15 of the FCC Rules. Operation is subject
recycle it responsibly to promote the sustainable reuse of material
to the following two conditions:
resources. To return your used device, please use the return and
(1) This device may not cause harmful interference, and
collection systems or contact the retailer where the product was
(2) This device must accept any interference received, including interference that may cause
purchased. They can take this product for environmental safe recycling.
undesired operation.
Company of License Holder：Philio Technology Corporation
FCC Caution: Any changes or modifications not expressly approved by the party responsible
Address of License Holder：8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City
for compliance could void the user's authority to operate this equipment.
24257, Taiwan(R.O.C)
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital de-
FCC RF Exposure Information (SAR)
vice, pursuant to Part 15 of the FCC Rules.
1. To comply with FCC RF exposure compliance requirements, a separation distance of at least
These limits are designed to provide reasonable protection against harmful interference in a
20 cm must be maintained between the antenna of this device and all persons.
residential installation.
2. This Transmitter must not be co-located or operating in conjunction with any other
This equipment generates, uses and can radiate radio frequency energy and, if not installed
antenna or transmitter.
and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 7
Language                        : zh-TW
Creator                         : Writer
Producer                        : LibreOffice 5.0
Create Date                     : 2017:01:09 11:03:31+08:00

EXIF Metadata provided by EXIF.tools