Philips Tda6107Jf Users Manual Triple Video Output Amplifier

TDA6107JF to the manual 1e50f9a6-3094-431c-ba53-68f314c79b6e

: Philips Philips-Tda6107Jf-Users-Manual-384835 philips-tda6107jf-users-manual-384835 philips pdf

Open the PDF directly: View PDF .
Page Count: 20

Download
Open PDF In Browser	View PDF

INTEGRATED CIRCUITS

DATA SHEET

TDA6107JF
Triple video output amplifier
Product specification

2002 Oct 18

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

FEATURES

GENERAL DESCRIPTION

• Typical bandwidth of 5.5 MHz for an output signal of
60 V (p-p)

The TDA6107JF includes three video output amplifiers
and is intended to drive the three cathodes of a colour CRT
directly. The device is contained in a plastic DIL-bent-SIL
9-pin medium power (DBS9MPF) package, and uses
high-voltage DMOS technology.

• High slew rate of 900 V/µs
• No external components required
• Very simple application

To obtain maximum performance, the amplifier should be
used with black-current control.

• Single supply voltage of 200 V
• Internal reference voltage of 2.5 V
• Fixed gain of 50
• Black-Current Stabilization (BCS) circuit with voltage
window from 1.8 to 6 V and current window from
−100 µA to 10 mA
• Thermal protection
• Internal protection against positive flashover discharges
appearing on the CRT.
ORDERING INFORMATION
TYPE
NUMBER
TDA6107JF

2002 Oct 18

PACKAGE
NAME
DBS9MPF

DESCRIPTION
plastic DIL-bent-SIL medium power package with fin; 9 leads

2

VERSION
SOT111-1

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

BLOCK DIAGRAM
VDD

handbook, full pagewidth

6
MIRROR 5

MIRROR 1

TDA6107JF

CASCODE 1

3×

MIRROR 4
CURRENT
SOURCE

9, 8, 7

1×

Voc(3),
Voc(2),
Voc(1)

1×
Rf

THERMAL
PROTECTION
CIRCUIT
Vi(1),
Vi(2),
Vi(3)

VIP
REFERENCE

1, 2, 3

DIFFERENTIAL
STAGE

5

MIRROR 3
Ri
Ra

3×

CASCODE 2

MIRROR 2
4
MBL525

Fig.1 Block diagram (one amplifier shown).

PINNING
SYMBOL

PIN

DESCRIPTION

Vi(1)

1

inverting input 1

Vi(2)

2

inverting input 2

Vi(3)

3

inverting input 3

GND

4

ground (fin)

Iom

5

black-current measurement output

VDD

6

supply voltage

Voc(3)

7

cathode output 3

Voc(2)

8

cathode output 2

Voc(1)

9

cathode output 1

handbook, halfpage

Vi(1)

1

Vi(2)

2

Vi(3)

3

GND

4

Iom

5 TDA6107JF

VDD

6

Voc(3)

7

Voc(2)

8

Voc(1)

9
MBL524

Fig.2 Pin configuration.

2002 Oct 18

3

Io(m)

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134); voltages measured with respect to pin 4
(ground); currents as specified in Fig.1; unless otherwise specified.
SYMBOL

PARAMETER

MIN.

MAX.

UNIT

VDD

supply voltage

0

250

V

Vi

input voltage at pins 1 to 3

0

12

V

Vo(m)

measurement output voltage

0

6

V

Voc

cathode output voltage

0

VDD

V

Iocsm(L)

LOW non-repetitive peak cathode output current at a flashover
discharge of 100 µC

0

3

A

Iocsm(H)

HIGH non-repetitive peak cathode output current at a flashover
discharge of 100 nC

0

6

A

Tstg

storage temperature

−55

+150

°C

Tj

junction temperature

−20

+150

°C

Ves

electrostatic handling voltage
Human Body Model (HBM)

−

3000

V

Machine Model (MM)

−

300

V

HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is
desirable to take normal precautions appropriate to handling MOS devices (see “Handling MOS Devices” ).
QUALITY SPECIFICATION
Quality specification “SNW-FQ-611 part D” is applicable and can be found in the “Quality reference Handbook”.
The handbook can be ordered using the code 9397 750 00192.

2002 Oct 18

4

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

THERMAL CHARACTERISTICS
SYMBOL

PARAMETER

CONDITIONS

Rth(j-a)

thermal resistance from junction to ambient

Rth(j-fin)

thermal resistance from junction to fin

Rth(h-a)

thermal resistance from heatsink to ambient

VALUE

note 1

UNIT

56

K/W

11

K/W

18

K/W

Note
1. An external heatsink is necessary.
Thermal protection
The internal thermal protection circuit gives a decrease of
the slew rate at high temperatures: 10% decrease at
130 °C and 30% decrease at 145 °C (typical values on the
spot of the thermal protection circuit).

MBH989

8

handbook, halfpage

Ptot
(W)
(1)

6

4

(2)

handbook, halfpage

outputs

2

5 K/W
thermal protection circuit

0
−40

6 K/W
0

40

80

120
160
Tamb (°C)

fin

MGK279

(1) Infinite heatsink.
(2) No heatsink.

Fig.3 Power derating curves.

2002 Oct 18

Fig.4 Equivalent thermal resistance network.

5

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

CHARACTERISTICS
Operating range: Tj = −20 to +150 °C; VDD = 180 to 210 V. Test conditions: Tamb = 25 °C; VDD = 200 V;
Vo(c1) = Vo(c2) = Vo(c3) = 1⁄2VDD; CL = 10 pF (CL consists of parasitic and cathode capacitance); Rth(h-a) = 18 K/W
(measured in test circuit of Fig.8); unless otherwise specified.
SYMBOL

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

Iq

quiescent supply current

5.6

6.6

7.6

mA

Vref(int)

internal reference voltage
(input stage)

−

2.5

−

V

Ri

input resistance

−

3.6

−

kΩ

G

gain of amplifier

47.5

51.0

55.0

∆G

gain difference

−2.5

0

+2.5

VO(oc)

nominal output voltage at
pins 7, 8 and 9 (DC value)

Ii = 0 µA

116

129

142

V

∆VO(oc)(offset)

differential nominal output
offset voltage between
pins 7 and 8, 8 and 9 and
9 and 7 (DC value)

Ii = 0 µA

−

0

5

V

∆Vo(c)(T)

output voltage temperature
drift at pins 7, 8 and 9

−

10

−

mV/K

−

0

−

mV/K

−50

−

+50

µA

−100 µA < Io(c) < 100 µA;
1.5 V < Vi < 5.5 V;
1.8 V < Vo(m) < 6 V

−0.9

−1.0

−1.1

−100 µA ≤ Io(c) < 10 mA;
1.5 V < Vi < 5.5 V;
1.8 V < Vo(m) < 4 V

−0.9

−1.0

−1.1

∆Vo(c)(T)(offset) differential output offset
voltage temperature drift
between pins 7 and 8,
8 and 9 and 7 and 9
Io(m)(offset)

offset current of measurement Io(c) = 0 µA;
output (for three channels)
1.5 V < Vi < 5.5 V;
1.8 V < Vo(m) < 6 V

∆Io(m)/∆Io(c)

linearity of current transfer
(for three channels)

Io(c)(max)

maximum peak output current 50 V < Vo(c) < VDD − 50 V
(pins 7, 8 and 9)

−

20

−

mA

Vo(c)(min)

minimum output voltage
(pins 7, 8 and 9)

Vi = 7.0 V; at Io(c) = 0 mA;
note 1

−

−

10

V

Vo(c)(max)

maximum output voltage
(pins 7, 8 and 9)

Vi = 1.0 V; at Io(c) = 0 mA;
note 1

VDD − 15 −

−

V

BS

small signal bandwidth
(pins 7, 8 and 9)

Vo(c) = 60 V (p-p)

−

5.5

−

MHz

BL

large signal bandwidth
(pins 7, 8 and 9)

Vo(c) = 100 V (p-p)

−

4.5

−

MHz

tPco

cathode output propagation
time 50% input to 50% output
(pins 7, 8 and 9)

Vo(c) = 100 V (p-p) square
wave; f <1 MHz;
tr = tf = 40 ns
(pins 1, 2 and 3);
see Figs 6 and 7

−

60

−

ns

2002 Oct 18

6

Philips Semiconductors

Product specification

Triple video output amplifier

SYMBOL

PARAMETER

TDA6107JF

CONDITIONS

MIN.

TYP.

MAX.

UNIT

∆tPco

difference in cathode output
propagation time 50% input to
50% output (pins 7 and 8,
7 and 9 and 8 and 9)

Vo(c) = 100 V (p-p) square
wave; f < 1 MHz;
tr = tf = 40 ns
(pins 1, 2 and 3)

−10

0

+10

ns

to(r)

cathode output rise time
10% output to 90% output
(pins 7, 8 and 9)

Vo(c) = 50 to 150 V square
wave; f < 1 MHz; tf = 40 ns
(pins 1, 2 and 3); see Fig.6

67

91

113

ns

to(f)

cathode output fall time
90% output to 10% output
(pins 7, 8 and 9)

Vo(c) = 150 to 50 V square
wave; f < 1 MHz; tr = 40 ns
(pins 1, 2 and 3); see Fig.7

67

91

113

ns

tst

settling time 50% input to
99% < output < 101%
(pins 7, 8 and 9)

Vo(c) = 100 V (p-p) square
wave; f < 1 MHz;
tr = tf = 40 ns
(pins 1, 2 and 3);
see Figs 6 and 7

−

−

350

ns

SR

slew rate between
50 V to (VDD − 50 V)
(pins 7, 8 and 9)

Vi = 4 V (p-p) square wave;
f < 1 MHz; tr = tf = 40 ns
(pins 1, 2 and 3)

−

900

−

V/µs

Ov

cathode output voltage
overshoot (pins 7, 8 and 9)

Vo(c) = 100 V (p-p) square
wave; f < 1 MHz;
tr = tf = 40 ns
(pins 1, 2 and 3);
see Figs 6 and 7

−

2

−

%

PSRR

power supply rejection ratio

f < 50 kHz; note 2

−

55

−

dB

αct(DC)

DC crosstalk between
channels

−

−50

−

dB

Notes
1. See also Fig.5 for the typical DC-to-DC transfer of VI to VO(oc).
2. The ratio of the change in supply voltage to the change in input voltage when there is no change in output voltage.

2002 Oct 18

7

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

MBH988

200

handbook, halfpage

Vo(c)
(V)

160

129

120

80

40

0
0

2

2.5

4

Vi (V)

6

Fig.5 Typical DC-to-DC transfer of VI to VOC.

2002 Oct 18

8

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

4.04
Vi
(V)

3.08
t

2.12

tst
Ov (in %)

151

150
140
149

Vo(c)
(V)
100

60
50

t
to(r)
MGK280

tPco

Fig.6 Output voltage (pins 7, 8 and 9) rising edge as a function of the AC input signal.

2002 Oct 18

9

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

4.04
Vi
(V)

3.08
t

2.12

tst

150
140
Vo(c)
(V)
100
Ov (in %)

51

60
50
49
t
to(f)
MGK281

tPco

Fig.7 Output voltage (pins 7, 8 and 9) falling edge as a function of the AC input signal.

2002 Oct 18

10

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

Cathode output

Dissipation

The cathode output is protected against peak current
(caused by positive voltage peaks during high-resistance
flash) of 3 A maximum with a charge content of 100 µC (1).

Regarding dissipation, distinction must first be made
between static dissipation (independent of frequency) and
dynamic dissipation (proportional to frequency).

The cathode is also protected against peak currents
(caused by positive voltage peaks during low-resistance
flash) of 6 A maximum with a charge content of 100 nC (1).

The static dissipation of the TDA6107JF is due to voltage
supply currents and load currents in the feedback network
and CRT.

The DC voltage of VDD (pin 6) must be within the operating
range of 180 to 210 V during the peak currents.

The static dissipation Pstat equals:

Flashover protection

Where:

P stat = V DD × I DD + 3 × V OC × I OC

VDD = supply voltage

The TDA6107JF incorporates protection diodes against
CRT flashover discharges that clamp the cathodes output
voltage up to a maximum of VDD + Vdiode.

IDD = supply current
VOC = DC value of cathode voltage

To limit the diode current an external 1.5 kΩ carbon
high-voltage resistor in series with the cathode output and
a 2 kV spark gap are needed (for this resistor value, the
CRT has to be connected to the main PCB (1).

The dynamic dissipation Pdyn equals:

VDD must be decoupled to GND:

Where:

IOC = DC value of cathode current.
P dyn = 3 × V DD × ( C L + C int ) × f i × V oc(p-p) × δ

1. With a capacitor >20 nF with good HF behaviour
(e.g. foil); this capacitor must be placed as close as
possible to pins 6 and 4, but definitely within 5 mm.

CL = load capacitance

2. With a capacitor >3.3 µF on the picture tube base
print, depending on the CRT size.

fi = input frequency

Cint = internal load capacitance (≈4 pF)
Voc(p-p) = output voltage (peak-to-peak value)
δ = non-blanking duty cycle.

Switch-off behaviour

The IC must be mounted on the picture tube base print to
minimize the load capacitance CL.

The switch-off behaviour of the TDA6107JF is controllable.
This is because the output pins of the TDA6107JF are still
under control of the input pins for low power supply
voltages (approximately 30 V and higher).
Bandwidth
The addition of the flash resistor produces a decreased
bandwidth and increases the rise and fall times; see
“Application Note AN96072”.
(1)External protection against higher currents is described
in “Application Note AN96072”.

2002 Oct 18

11

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

TEST AND APPLICATION INFORMATION

VDD

handbook, full pagewidth

C1
Vi(1)

J1

22 µF

6

Rf
1

Ri

Vof

C2

1
Ra

C7
20 nF

Voc(1)

9
C10
6.8 pF

Iom

22 nF

C8
10 µF

R1
2 MΩ

C9
3.2 pF

C3
Vi(2)

J2

22 µF

Rf
2

Ri

Vof

C4

2
Ra

Voc(2)

C11
136 pF

R2
100 kΩ

C13
6.8 pF

R3
2 MΩ

C14
136 pF

R4
100 kΩ

C16
6.8 pF

R5
2 MΩ

C17
136 pF

R6
100 kΩ

8

Iom

22 nF

probe 1

C12
3.2 pF

C5
Vi(3)

22 µF

J3

Rf
3

Ri

Vof

C6

3
Ra

Voc(3)

7

Iom

22 nF

probe 2

C15
3.2 pF
VIP
REFERENCE

probe 3

5

TDA6107JF

Vo(m)

4

4V
MBL526

Current sources J1, J2 and J3 are to be tuned so that Vo(c) of pins 9, 8 and 7 is set to 100 V.

Fig.8 Test circuit.

2002 Oct 18

12

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

INTERNAL CIRCUITRY

handbook, full pagewidth

GND

VDD

4

6

to cascode
stage

to black current
measurement circuit

TDA6107JF

1, 2, 3

(1)

esd

from
input
circuit

esd

flash
7, 8, 9

esd
to black current
measurement circuit
from
control
circuit
5
esd

6.8 V

from
input
circuit

Vbias

from black
current
measurement
circuit

esd

esd

from
control
circuit

to black current
measurement circuit

to black current
measurement circuit

MBL527

(1) All pins have an energy protection for positive or negative overstress situations.

Fig.9 Internal pin configuration.

2002 Oct 18

13

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

PACKAGE OUTLINE
DBS9MPF: plastic DIL-bent-SIL medium power package with fin; 9 leads

SOT111-1

D

D1
A2

q
P

P1

Q

A3
q2

q1

A

seating plane

A4

E

pin 1 index

c

L
1

9
e2

b

e

Z
b2

0

θ

w M

b1

5

10 mm

scale
DIMENSIONS (mm are the original dimensions)
UNIT

A

mm

18.5
17.8

A2
A3
max.
3.7

8.7
8.0

A4

b

b1

b2

c

D (1)

D1

E (1)

e

e2

15.5 1.40 0.67 1.40 0.48 21.8 21.4 6.48 2.54 2.54
15.1 1.14 0.50 1.14 0.38 21.4 20.7 6.20

L

P

P1

3.9
3.4

2.75
2.50

3.4
3.2

Q

q

1.75 15.1
1.55 14.9

q1

q2

w

Z (1)
max.

θ

4.4
4.2

5.9
5.7

0.25

1.0

65o
55o

Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION

REFERENCES
IEC

JEDEC

EIAJ

ISSUE DATE
92-11-17
95-03-11

SOT111-1

2002 Oct 18

EUROPEAN
PROJECTION

14

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF
The total contact time of successive solder waves must not
exceed 5 seconds.

SOLDERING
Introduction to soldering through-hole mount
packages

The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg(max)). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.

This text gives a brief insight to wave, dip and manual
soldering. A more in-depth account of soldering ICs can be
found in our “Data Handbook IC26; Integrated Circuit
Packages” (document order number 9398 652 90011).
Wave soldering is the preferred method for mounting of
through-hole mount IC packages on a printed-circuit
board.

Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the
package, either below the seating plane or not more than
2 mm above it. If the temperature of the soldering iron bit
is less than 300 °C it may remain in contact for up to
10 seconds. If the bit temperature is between
300 and 400 °C, contact may be up to 5 seconds.

Soldering by dipping or by solder wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joints for more than 5 seconds.

Suitability of through-hole mount IC packages for dipping and wave soldering methods
SOLDERING METHOD
PACKAGE
DIPPING
DBS, DIP, HDIP, SDIP, SIL

WAVE
suitable(1)

suitable

Note
1. For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board.

2002 Oct 18

15

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF

DATA SHEET STATUS
LEVEL

DATA SHEET
STATUS(1)

PRODUCT
STATUS(2)(3)
Development

DEFINITION

I

Objective data

II

Preliminary data Qualification

This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in order to improve the design and supply the best possible
product.

III

Product data

This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in order
to improve the design, manufacturing and supply. Relevant changes will
be communicated via a Customer Product/Process Change Notification
(CPCN).

Production

This data sheet contains data from the objective specification for product
development. Philips Semiconductors reserves the right to change the
specification in any manner without notice.

Notes
1. Please consult the most recently issued data sheet before initiating or completing a design.
2. The product status of the device(s) described in this data sheet may have changed since this data sheet was
published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
DEFINITIONS

DISCLAIMERS

Short-form specification  The data in a short-form
specification is extracted from a full data sheet with the
same type number and title. For detailed information see
the relevant data sheet or data handbook.

Life support applications  These products are not
designed for use in life support appliances, devices, or
systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips
Semiconductors customers using or selling these products
for use in such applications do so at their own risk and
agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.

Limiting values definition  Limiting values given are in
accordance with the Absolute Maximum Rating System
(IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device.
These are stress ratings only and operation of the device
at these or at any other conditions above those given in the
Characteristics sections of the specification is not implied.
Exposure to limiting values for extended periods may
affect device reliability.

Right to make changes  Philips Semiconductors
reserves the right to make changes in the products including circuits, standard cells, and/or software described or contained herein in order to improve design
and/or performance. When the product is in full production
(status ‘Production’), relevant changes will be
communicated via a Customer Product/Process Change
Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these
products, conveys no licence or title under any patent,
copyright, or mask work right to these products, and
makes no representations or warranties that these
products are free from patent, copyright, or mask work
right infringement, unless otherwise specified.

Application information  Applications that are
described herein for any of these products are for
illustrative purposes only. Philips Semiconductors make
no representation or warranty that such applications will be
suitable for the specified use without further testing or
modification.

2002 Oct 18

16

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF
NOTES

2002 Oct 18

17

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF
NOTES

2002 Oct 18

18

Philips Semiconductors

Product specification

Triple video output amplifier

TDA6107JF
NOTES

2002 Oct 18

19

Philips Semiconductors – a worldwide company

Contact information
For additional information please visit http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com.

SCA74

© Koninklijke Philips Electronics N.V. 2002

All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.

Printed in The Netherlands

753504/02/pp20

Date of release: 2002

Oct 18

Document order number:

9397 750 10545



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Modify Date                     : 2002:10:22 10:07:45+02:00
Create Date                     : 2002:04:12 15:36:57Z
Subject                         : TDA6107JF
Keywords                        : TDA6107JF, Triple, video, output, amplifier
Page Count                      : 20
Page Mode                       : UseOutlines
Producer                        : Acrobat Distiller Daemon 3.0 for HP-UX A.09.01 and later (HPPA)
Mod Date                        : 2002:10:22 10:07:45+02:00
Creation Date                   : 2002:04:12 15:36:57Z
Author                          : Philips Semiconductors
Metadata Date                   : 2002:10:22 10:07:45+02:00
Title                           : TDA6107JF  Triple video output amplifier
Description                     : TDA6107JF
Creator                         : Philips Semiconductors

EXIF Metadata provided by EXIF.tools