Pioneer K047 CD RDS RECEIVER User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1636997
Application ID	pI18jzg7OJLHNYzat0bXQw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	106.14kB (1326699 bits)
Date Submitted	2012-02-14 00:00:00
Date Available	2012-08-12 00:00:00
Creation Date	2011-11-22 02:01:34
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2011-11-22 14:14:57
Document Title	User Manual
Document Creator	Arbortext Advanced Print Publisher 9.1.520/W Unicode

Operation Manual
CD RDS RECEIVER
DEH-80PRS
English
Contents
Thank you for purchasing this PIONEER product.
To ensure proper use, please read through this manual before using this product. It
is especially important that you read and observe WARNINGs and CAUTIONs in
this manual. Please keep the manual in a safe and accessible place for future reference.
Before you start
Information to User 3
The Safety of Your Ears is in Your Hands 3
About this unit 4
After-sales service for Pioneer products 4
In case of trouble 5
Visit our website 5
Resetting the microprocessor 5
Switching the DSP setting mode 5
Switching between RCA input modes 6
Demo mode 6
About this manual 6
Operating this unit
Head unit 7
Remote control 7
Set up menu 8
Basic operations 8
Use and care of the remote control 9
Menu operations identical for function
settings/audio adjustments/initial settings/
lists 10
Tuner 10
CD/CD-R/CD-RW and external storage
devices (USB, SD) 12
iPod 15
Using Pandoraâ 17
Audio adjustments 19
Using Bluetooth wireless technology 32
Initial settings 36
Other functions 37
Additional information
Troubleshooting 41
Error messages 42
Handling guidelines 44
Compressed audio compatibility (disc, USB,
SD) 46
iPod compatibility 47
Sequence of audio files 47
En
Bluetooth profiles 48
Copyright and trademark 48
Specifications 50
Section
Before you start
Information to User
Alteration or modifications carried out without
appropriate authorization may invalidate the
user’s right to operate the equipment.
Note
This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Before you start
FCC ID: AJDK047
MODEL NO.: DEH-80PRS
IC: 775E-K047
This device complies with Part 15 of FCC Rules
and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause
interference, and (2) this device must accept
any interference, including interference that
may cause undesired operation of this device.
This transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.
The antenna for Bluetooth cannot be removed
(or replaced) by user.
This equipment complies with FCC/IC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment
has very low levels of RF energy that it deemed
to comply without maximum permissive exposure evaluation (MPE). But it is desirable that
it should be installed and operated keeping the
radiator at least 20 cm or more away from person’s body (excluding extremities: hands,
wrists, feet and ankles).
01
The Safety of Your Ears is in
Your Hands
Get the most out of your equipment by playing
it at a safe level—a level that lets the sound
come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound
can be deceiving. Over time, your hearing
“comfort level” adapts to higher volumes of
sound, so what sounds “normal” can actually
be loud and harmful to your hearing. Guard
against this by setting your equipment at a
safe level BEFORE your hearing adapts.
En
Section
01
Before you start
ESTABLISH A SAFE LEVEL:
! Set your volume control at a low setting.
! Slowly increase the sound until you can
hear it comfortably and clearly, without distortion.
! Once you have established a comfortable
sound level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
! Do not turn up the volume so high that you
can’t hear what’s around you.
! Use caution or temporarily discontinue use
in potentially hazardous situations.
! Do not use headphones while operating a
motorized vehicle; the use of headphones
may create a traffic hazard and is illegal in
many areas.
About this unit
The tuner frequencies on this unit are allocated for use in North America. Use in other
areas may result in poor reception.
WARNING
Handling the cord on this product or cords associated with accessories sold with the product
may expose you to chemicals listed on proposition 65 known to the State of California and other
governmental entities to cause cancer and birth
defect or other reproductive harm. Wash hands
after handling.
CAUTION:
USE OF CONTROL OR ADJUSTMENT OR
PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
CAUTION:
THE USE OF OPTICAL INSTRUMENTS
WITH THIS PRODUCT WILL INCREASE
EYE HAZARD.
En
CAUTION
! Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and overheating could result from contact with liquids.
! Always keep the volume low enough to hear
outside sounds.
! Avoid exposure to moisture.
! If the battery is disconnected or discharged,
any preset memory will be erased.
Important (Serial number)
The serial number is located on the bottom of
this unit. For your own security and convenience,
be sure to record this number on the enclosed
warranty card.
Note
Function setting operations are completed even if
the menu is cancelled before the operations are
confirmed.
After-sales service for
Pioneer products
Please contact the dealer or distributor from
where you purchased this unit for after-sales
service (including warranty conditions) or any
other information. In case the necessary information is not available, please contact the
companies listed below:
Please do not ship your unit to the companies
at the addresses listed below for repair without
advance contact.
Section
Before you start
! Before using this unit for the first time after
installation
! If the unit fails to operate properly
! When strange or incorrect messages appear on the display
1 Remove the front panel.
For details, refer to Removing the front panel to
protect your unit from theft on page 9.
Before you start
U.S.A.
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION DEPARTMENT
340 Ferrier Street
Unit 2
Markham, Ontario L3R 2Z5, Canada
1-877-283-5901
905-479-4411
01
2 Press RESET with a pen tip or other
pointed instrument.
For warranty information please see the Limited Warranty sheet included with this unit.
In case of trouble
Should this unit fail to operate properly, please
contact your dealer or nearest authorized
PIONEER Service Station.
Visit our website
http://www.pioneerelectronics.com
in Canada
http://www.pioneerelectronics.ca
! Learn about product updates (such as firmware updates) for your product.
! Register your product to receive notices
about product updates and to safeguard
purchase details in our files in the event of
loss or theft.
! Access owner’s manuals, spare parts information, service information, and much
more.
RESET button
Switching the DSP setting
mode
This unit features two operation modes: the 3way network mode (NW) and the standard
mode (STD). You can switch between modes
as desired. Initially, the DSP setting is set to
the standard mode (STD).
! After switching, reset the microprocessor.
WARNING
Do not use the unit in standard mode when a
speaker system for 3-way network mode is connected to this unit. This may cause damage to
the speakers.
Resetting the microprocessor
The microprocessor must be reset in the following situations:
En
Section
01
Before you start
1 Use a thin, flathead screwdriver to
change the DSP switch on the bottom of
this unit.
! L (Low) - If inputting from the RCA output of
a connected device
! H (High) - If inputting from the speaker output of a connected device
Demo mode
2 Press RESET with a pen tip or other
pointed instrument.
Note
This unit's audio settings will continue to remain
in the memory even if the battery is disconnected
or the microprocessor reset. If you want to reset
the audio settings, refer to AUDIO reset (audio
reset) on page 36.
Switching between RCA
input modes
If you connect the unit to an audio device with
RCA output, or to one with no RCA output,
you can set it up so that the audio from the
audio device is output through speakers connected to the unit. Change settings as necessary based on whether the connected device
has RCA output or not.
! For more details on how to connect the
unit, refer to the installation manual.
% Use a thin, flathead screwdriver to
change the RCA input mode switch on the
bottom of this unit.
En
Important
! Failure to connect the red lead (ACC) of this
unit to a terminal coupled with ignition switch
on/off operations may lead to battery drain.
! Remember that if the feature demo continues
operating when the car engine is turned off, it
may drain battery power.
The demo starts automatically if you do not operate this unit within about 30 seconds since it
was last operated or if the ignition switch is
set to ACC or ON while it is turned off. To cancel the demo mode, press and hold ( /DISP).
Press and hold ( /DISP) again to start. You
can also deactivate demo mode in the initial
settings. Select Demonstration (demo display
setting) and turn off the demo display. For details, refer to Initial settings on page 36.
About this manual
! In the following instructions, USB memories, USB portable audio players, and SD
memory cards are collectively referred to as
“external storage devices (USB, SD)”. If
only USB memories and USB portable
audio players are indicated, they are collectively referred to as “USB storage devices”.
! In this manual, iPod and iPhone will be referred to as “iPod”.
Section
Operating this unit
02
Head unit
Remote control
Remote controller buttons marked with the
same numbers as on the unit operate in the
same way as the corresponding unit button regardless of button name.
b a 98
Part
BAND/
LEVER
SRC/OFF
/DISP
MULTI-CONTROL
(M.C.)
(list)
Disc loading slot
h (eject)
AUX input jack
(3.5 mm stereo
jack)
Auto TA and EQ microphone input
jack
Use to connect an
auto TA and EQ microphone.
Operation
VOLUME
Press to increase or decrease volume.
MUTE
Press to mute. Press again to unmute.
a/b/c/d
Press to perform manual seek
tuning, fast forward, reverse and
track search controls.
Also used for controlling functions.
(iPod)
Open button
Part
Part
(phone/on
hook)
Operating this unit
1 2 3 4
While operating the phone, press
to end a call or reject an incoming
call.
SD memory card
slot
Remove the front
panel to access the
SD memory card
slot.
RESET
EQ/DISP OFF
Press to start talking on the
phone while operating a phone.
Press to pause or resume playback.
LIST/
ENTER
Press to display the disc title,
track title, folder, or file list depending on the source.
While in the operating menu,
press to control functions.
CAUTION
Use a Pioneer USB cable when connecting the
USB audio player/USB memory device as devices
connected to the unit directly will protrude out,
which is dangerous.
Do not use unauthorized products.
En
Section
Operating this unit
02
Set up menu
Demonstration (demo display setting)
When you turn the ignition switch to ON after
installation, set up menu appears on the display.
You can set up the menu options below.
1 Turn M.C. to set the demo display to off.
2 Press M.C. to confirm the selection.
Quit appears.
1 After installation of this unit, turn the
ignition switch to ON.
SET UP appears.
Turn M.C. to switch to YES.
# If you do not operate for 30 seconds, the set
up menu will not be displayed.
# If you prefer not to set up at this time, turn
M.C. to switch to NO.
If you select NO, you cannot set up in the set up
menu.
Press M.C. to select.
4 Perform the following procedures to
set the menu.
To proceed to the next menu option, you need
to confirm your selection.
Language select (multi-language)
1 Turn M.C. to select the desired language.
English—Français—Español
2 Press M.C. to confirm the selection.
Calendar (setting the date)
Turn M.C. to change the year.
Press M.C. to select day.
Turn M.C. to change the day.
Press M.C. to select month.
Turn M.C. to change the month.
Press M.C. to confirm the selection.
Clock (setting the clock)
Turn M.C. to adjust hour.
Press M.C. to select minute.
Turn M.C. to adjust minute.
Press M.C. to confirm the selection.
Contrast (display contrast setting)
1 Turn M.C. to adjust the contrast level.
0 to 15 is displayed as the level is increased or decreased.
2 Press M.C. to confirm the selection.
En
5 To finish your settings, turn M.C. to select YES.
# If you prefer to change your setting again, turn
M.C. to switch to NO.
Press M.C. to select.
Notes
! Because demonstration mode is the function
for displaying at stores, do not use this function while driving.
! You can set up the menu options in the initial
settings. For details about the settings, refer to
Initial settings on page 36.
! You can cancel set up menu by pressing SRC/
OFF.
Basic operations
Important
! Handle gently when removing or attaching
the front panel.
! Avoid subjecting the front panel to excessive
shock.
! Keep the front panel out of direct sunlight and
high temperatures.
! To avoid damaging the device or vehicle interior, remove any cables and devices attached
to the front panel before detaching it.
Section
Operating this unit
Re-attaching the front panel
1 Reattach the front panel by holding it upright to
the unit and clipping it securely into the mounting hooks.
communications for the USB storage device
first before proceeding.
! If connecting both USB1 (USB storage device1)/iPod1 (iPod connected using USB
input1) and USB2 (USB storage device2)/
iPod2 (iPod connected using USB input2) at
the same time, use a Pioneer USB cable (CDU50E) in addition to the regular Pioneer USB
cable.
! Set the Pandora application to off when you
select iPod source. The source may be
switched to Pandora automatically if the application is on.
Operating this unit
Removing the front panel to protect your unit from
theft
The front panel can be detached to deter theft.
1 Press the open button to open the front panel.
2 Grip the left side of the front panel and pull it
gently outward.
Take care not to grip it too tightly or to drop the
front panel and protect it from contact with water
or other fluids to prevent permanent damage.
3 Always keep the detached front panel in a protection device such as a protection case.
02
Use and care of the remote
control
Turning the unit on
1 Press SRC/OFF to turn the unit on.
Turning the unit off
1 Press and hold SRC/OFF until the unit turns off.
Selecting a source
1 Press SRC/OFF to cycle between:
TUNER (tuner)—CD (CD player)—USB1 (USB1)/
iPod1 (iPod1)—Pandora1 (Pandora1)—USB2
(USB2)/iPod2 (iPod2)—Pandora2 (Pandora2)—
SD (SD memory card)—AUX1 (AUX1)—AUX2
(AUX2)—BT Audio (BT audio)
Using the remote control
1 Point the remote control in the direction of the
front panel to operate.
When using for the first time, pull out the film
protruding from the tray.
Replacing the battery
1 Slide the tray out on the back of the remote control.
2 Insert the battery with the plus (+) and minus (–)
poles aligned properly.
Adjusting the volume
1 Turn M.C. to adjust the volume.
CAUTION
For safety reasons, park your vehicle when removing the front panel.
Notes
! When this unit’s blue/white lead is connected
to the vehicle’s auto-antenna relay control
terminal, the vehicle’s antenna extends when
this unit’s source is turned on. To retract the
antenna, turn the source off.
! When there are two USB storage devices connected to this unit and you want to switch between them for playback, disconnect
WARNING
! Keep the battery out of the reach of children.
Should the battery be swallowed, consult a
doctor immediately.
! Batteries (battery pack or batteries installed)
must not be exposed to excessive heat such
as sunshine, fire or the like.
CAUTION
! Use one CR2025 (3 V) lithium battery.
En
Section
02
Operating this unit
! Remove the battery if the remote control is not
used for a month or longer.
! There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the
same or equivalent type.
! Do not handle the battery with metallic tools.
! Do not store the battery with metallic objects.
! If the battery leaks, wipe the remote control
completely clean and install a new battery.
! When disposing of used batteries, comply
with governmental regulations or environmental public institutions’ rules that apply in your
country/area.
! “Perchlorate Material – special handling may
apply.
See www.dtsc.ca.gov/hazardouswaste/
perchlorate. (Applicable to California, U.S.A.)”
Important
! Do not store the remote control in high temperatures or direct sunlight.
! The remote control may not function properly
in direct sunlight.
! Do not let the remote control fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
Menu operations identical
for function settings/audio
adjustments/initial
settings/lists
Returning to the previous display
Returning to the previous list/category (the folder/category one level higher)
1 Press /DISP.
Turning the demo display on or off
1 Press and hold /DISP.
Returning to the ordinary display
Canceling the initial setting menu
1 Press BAND/ .
10
En
Returning to the ordinary display from the list/category
1 Press BAND/ .
Selecting a function or list
1 Turn M.C. or LEVER.
! In this manual, “Turn M.C.” is used to describe
the operation used to select a function or list.
Tuner
Basic operations
4 5 6
RDS
4 5 6
Non-RDS or AM
TAG indicator
Tags transferring indicator
Band indicator
5 (stereo) indicator
LOC indicator
Appears when local seek tuning is on.
Preset number indicator
Signal level indicator
TEXT indicator
Shows when the radio text is received.
Program service name
Frequency indicator
Voltage indicator
Shows the battery voltage.
Section
Operating this unit
Selecting a band
1 Press BAND/ until the desired band (FM-1, FM2,FM-3 for FM or AM) is displayed.
Manual tuning (step by step)
1 Turn LEVER.
Seeking
1 Turn and hold down LEVER.
! While turning and holding down LEVER, you
can skip stations. Seek tuning starts as soon
as you release LEVER.
Storing and recalling stations
for each band
1 Press
(list).
The preset screen is displayed.
2 Use M.C. to store the selected frequency in the memory.
Turn to change the preset number. Press and
hold to store.
3 Use M.C. to select the desired station.
Turn to change the station. Press to select.
# All stations stored for FM bands can be recalled from each independent FM band.
# You can tune the channel up or down manually by pressing or .
# Press BAND/ or
(list) to return to the ordinary display.
Switching the display
Desired information can be displayed while
tag information has been broadcasting.
Selecting the desired text information
1 Press /DISP.
Frequency or program service name—song title
and artist name
Using iTunes tagging
This function can be operated with the following
iPod models.
— iPod touch 4th generation
— iPod touch 3rd generation
— iPod touch 2nd generation
— iPod touch 1st generation
— iPod classic 160GB
— iPod classic 120GB
— iPod classic
— iPod nano 6th generation
— iPod nano 5th generation
— iPod nano 4th generation
— iPod nano 3rd generation
— iPhone 4
— iPhone 3GS
— iPhone 3G
— iPhone
However, tag information can be stored in this
unit even while other iPod models are used.
The song information (tag) can be saved from
the broadcasting station to your iPod. The
songs will show up in a playlist called “Tagged
playlist” in iTunes the next time you sync your
iPod. Then you can directly buy the songs you
want from the iTunes Store.
! The tagged songs and the song that you
can buy from the iTunes Store may be different. Make sure to confirm the song before you make the purchase.
Operating this unit
! The level displayed on the voltage indicator may differ from the actual voltage
level.
02
Storing the tag information to this unit
1 Tune in to the broadcast station.
2 Press and hold M.C. if TAG is indicated in the display while desired song is broadcasting.
! While storing the tag data on this unit, TAG
flashes.
Storing the tagged information to your iPod
1 Connect an iPod to the USB cable using an iPod
Dock Connector.
2 Select Tags transfer from the function settings to
transfer tag information from this unit to the iPod.
Refer to Tags transfer (Tags transfer) on page 17.
! If you switch sources during tag transfer, the
transfer will stop. To cancel the transfer, select
Tags transfer from the function settings and
then try transferring the tag information again.
En
11
Section
Operating this unit
02
Using radio text
Displaying radio text
You can display the currently received radio text and
the three most recent radio texts.
(list) to display radio text.
1 Press and hold down
! You can turn off radio text display by pressing
/DISP, SRC/OFF or BAND/ .
! When no radio text is received, NO TEXT appears in the display.
2 Turn LEVER left or right to recall the three most
recent radio texts.
3 Press
or
to scroll.
Storing and recalling radio text
You can store data from up to six radio text transmissions to the RT Memo 1 to RT Memo 6 keys.
1 Display the radio text you want to store in the
memory.
(list).
2 Press
The preset screen is displayed.
3 Use LEVER to store the selected radio text.
Turn it to change the preset number. Press and
hold down M.C. to store.
4 Use LEVER to select the desired radio text.
Turn it to change the radio text. Press M.C. to select.
! To return to the ordinary display, press BAND/
or
(list).
! The tuner automatically stores the three latest radio text broadcasts received, replacing the oldest text with the newest text.
Local (local seek tuning)
Local seek tuning lets you tune in to only those radio
stations with sufficiently strong signals for good reception.
1 Press M.C. to turn local on.
! To cancel, press M.C. again.
2 Turn LEVER left or right to select the desired setting.
FM: Level 1—Level 2—Level 3—Level 4
AM: Level 1—Level 2
The highest level setting allows reception of only
the strongest stations, while lower levels allow the
reception of weaker stations.
Tuning Mode (LEVER tuning setting)
You can assign a function to the LEVER on the unit.
Select Manual (manual tuning) to tune up or down
manually or select Preset (preset channel) to switch
between preset channels.
1 Press M.C. to select Manual or Preset.
CD/CD-R/CD-RW and external
storage devices (USB, SD)
Basic operations
Function settings
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following procedures to set the function.
! If AM band is selected, only BSM, Local
and Tuning Mode are available.
BSM (best stations memory)
BSM (best stations memory) automatically stores the
six strongest stations in the order of their signal
strength.
1 Press M.C. to turn BSM on.
To cancel, press M.C. again.
12
En
1 Bit rate/sampling frequency indicator
Shows the bit rate or sampling frequency of
the current track (file) when the compressed
audio is playing.
! When playing back VBR (variable bit
rate)-recorded AAC files, the average bit
rate value is displayed. However, depending on the software used to decode
AAC files, VBR may be displayed.
2 Folder number indicator
Shows the folder number currently playing
when the compressed audio is playing.
3 Track number indicator
Section
Operating this unit
! The level displayed on the voltage indicator may differ from the actual voltage
level.
Opening the front panel
1 Press the open button.
Disc loading slot appears.
Playing a CD/CD-R/CD-RW
1 Insert the disc into the disc loading slot with the
label side up.
Ejecting a CD/CD-R/CD-RW
1 Press h (eject).
Playing songs on a USB storage device
1 Use a Pioneer USB cable to connect the USB storage device to the unit.
! Plug in the USB storage device using the USB
cable.
Stopping playback of files on a USB storage device
! You may disconnect the USB storage device at
any time.
Playing songs on an SD memory card
1 Remove the front panel.
For details, refer to Removing the front panel to
protect your unit from theft on page 9.
2 Insert an SD memory card into the SD card slot.
Insert it with the contact surface facing down,
and press on the card until it clicks and completely locks into place.
3 Re-attach the front panel.
4 Press SRC/OFF to select SD as the source.
Playback will start.
Stopping playback of files on an SD memory card
1 Remove the front panel.
For details, refer to Removing the front panel to
protect your unit from theft on page 9.
2 Press on the SD memory card until it clicks.
The SD memory card is ejected.
3 Pull out the SD memory card.
4 Re-attach the front panel.
Selecting a track
1 Turn LEVER.
Fast forwarding or reversing
1 Turn and hold down LEVER to the right or left.
Returning to root folder
1 Press and hold BAND/ .
Switching between compressed audio and CD-DA
1 Press BAND/ .
Switching between playback memory devices
You can switch between playback memory devices on
USB storage devices with more than one Mass Storage Device-compatible memory device.
1 Press BAND/ .
! You can switch between up to 32 different memory devices.
Operating this unit
4 PLAY/PAUSE indicator
5 S.Rtrv indicator
Appears when Sound Retriever function is on.
6 Song time (progress bar)
7 Play time indicator
8 Voltage indicator
Shows the battery voltage.
02
Notes
! When playing compressed audio, there is no
sound during fast forward or reverse.
! Disconnect USB storage devices from the unit
when not in use.
! If there are two USB storage devices connected to this unit, the device connected to
the input of the selected source is the one
that is operated.
! Disconnect communications for the USB storage device before switching to operation of
the other device.
Displaying text information
Selecting the desired text information
1 Press /DISP.
Notes
! Depending on the version of iTunes used to
write MP3 files to a disc or media file types, incompatible text stored within an audio file
may be displayed incorrectly.
! Text information items that can be changed
depend on the media.
Selecting a folder
1 Press
or .
En
13
Section
02
Operating this unit
Selecting and playing files/
tracks from the name list
If there are external storage devices (USB, SD)
connected to the unit, this function is only
available when Music browse is set to OFF.
Refer to Music browse (music browse) on
page 36.
(list) to switch to the file/track
1 Press
name list mode.
2 Use M.C. to select the desired file name
(or folder name).
Changing the file or folder name
1 Turn M.C.
You can also perform this operation by turning
LEVER.
Playing
1 When a file or track is selected, press M.C.
Viewing a list of the files (or folders) in the selected
folder
1 When a folder is selected, press M.C.
Playing a song in the selected folder
1 When a folder is selected, press and hold M.C.
Browsing for a song
! This function is only available when a file
on an external storage device (USB, SD) or
a song on an iPod is being played.
! If there are external storage devices (USB,
SD) connected to the unit, this function is
only available when Music browse is set to
USB memory1, USB memory2 or SD card.
Refer to Music browse (music browse) on
page 36.
(list) to switch to the top menu
1 Press
of the list search.
Use M.C. to select a category/song.
Changing the name of the song or category
1 Turn M.C.
Artists (artists)—Albums (albums)—Songs
(songs)—Genres (genres)
You can also perform this operation by turning
LEVER.
Playing
1 When a song is selected, press M.C.
Viewing a list of songs in the selected category
1 When a category is selected, press M.C.
Playing a song in the selected category
1 When a category is selected, press and hold M.C.
Searching the list by alphabet
1 When a list for the selected category is displayed,
to switch to alphabet search mode.
press
2 Turn M.C. to select a letter.
3 Press M.C. to display the alphabetical list.
Notes
! This unit must create an index in order to facilitate Artists, Albums, Songs, and Genres
searches. Typically, it will take approximately
70 seconds to create an index for 1 000 songs,
and we recommend that up to 3 000 songs be
used. Please note that certain types of file
may take longer to index than others.
! Depending on the number of files in the USB
storage device, there may be a delay when displaying a list.
! Keys may not have any effect during the creation of an index or list.
! Lists are recreated each time the unit is
turned on.
Function settings
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following procedures to set the function.
14
En
Section
Operating this unit
Play mode (repeat play)
iPod
Basic operations
Random mode (random play)
1 Press M.C. to turn random play on or off.
Link play (link play)
1 Press M.C. to display the setting mode.
2 Turn M.C. to change the mode; press to select.
! Artist – Plays an album of the artist currently
being played.
! Album – Plays a song from the album currently
being played.
! Genre – Plays an album from the genre currently
being played.
The selected song/album will be played after the currently playing song.
! This function is only available for external storage
devices (USB, SD).
Pause (pause)
1 Press M.C. to pause or resume.
Sound Retriever (sound retriever)
Automatically enhances compressed audio and restores rich sound.
1 Press M.C. to select the desired setting.
OFF (off)—1—2
1 is effective for low compression rates, and 2 is
effective for high compression rates.
Repeat indicator
Song number indicator
Shuffle indicator
PLAY/PAUSE indicator
S.Rtrv indicator
Appears when Sound Retriever function is on.
6 Song time (progress bar)
7 Play time indicator
8 Voltage indicator
Shows the battery voltage.
Operating this unit
1 Press M.C. to select a repeat play range.
CD/CD-R/CD-RW
! Disc repeat – Repeat all tracks
! Track repeat – Repeat the current track
! Folder repeat – Repeat the current folder
External storage device (USB, SD)
! All repeat – Repeat all files
! Track repeat – Repeat the current file
! Folder repeat – Repeat the current folder
02
! The level displayed on the voltage indicator may differ from the actual voltage
level.
Playing songs on an iPod
1 Connect an iPod to the USB cable using an iPod
Dock Connector.
Selecting a track (chapter)
1 Turn LEVER.
Fast forwarding or reversing
1 Turn and hold down LEVER to the right or left.
Selecting an album
or .
1 Press
Notes
! The iPod cannot be turned on or off when the
control mode is set to AUDIO.
! Disconnect headphones from the iPod before
connecting it to this unit.
! The iPod will turn off about two minutes after
the ignition switch is set to OFF.
Displaying text information
Selecting the desired text information
1 Press /DISP.
En
15
Section
Operating this unit
02
Browsing for a song
1 Press
(list) to switch to the top menu
of the list search.
Use M.C. to select a category/song.
Changing the name of the song or category
1 Turn M.C.
Playlists (playlists)—Artists (artists)—Albums
(albums)—Songs (songs)—Podcasts (podcasts)
—Genres (genres)—Composers (composers)—
Audiobooks (audiobooks)
You can also perform this operation by turning
LEVER.
Playing
1 When a song is selected, press M.C.
Viewing a list of songs in the selected category
1 When a category is selected, press M.C.
Playing a song in the selected category
1 When a category is selected, press and hold M.C.
Searching the list by alphabet
1 When a list for the selected category is displayed,
to switch to alphabet search mode.
press
2 Turn M.C. to select a letter.
3 Press M.C. to display the alphabetical list.
Notes
! You can play playlists created with the PC application (MusicSphere). The application will
be available on our website.
! Playlists that you created with the PC application (MusicSphere) are displayed in abbreviated form.
Playing songs related to the
currently playing song
You can play songs from the following lists.
• Album list of the currently playing artist
• Song list of the currently playing album
• Album list of the currently playing genre
1 Press and hold M.C. to switch to link
play mode.
2 Turn M.C. to change the mode; press to
select.
! Artist – Plays an album of the artist currently being played.
16
En
! Album – Plays a song from the album currently being played.
! Genre – Plays an album from the genre
currently being played.
The selected song/album will be played after
the currently playing song.
Notes
! The selected song/album may be canceled if
you operate functions other than link search
(e.g. fast forward and reverse).
! Depending on the song selected to play, the
end of the currently playing song and the beginning of the selected song/album may be
cut off.
Operating this unit’s iPod
function from your iPod
You can listen to the sound from your iPod applications using your car’s speakers, when
APP is selected.
This function is not compatible with the following iPod models.
— iPod with video
— iPod nano 1st generation
APP Mode is compatible with the following
iPod models.
! iPod touch 4th generation (software version
4.1 or later)
! iPod touch 3rd generation (software version
3.0 or later)
! iPod touch 2nd generation (software version 3.0 or later)
! iPod touch 1st generation (software version
3.0 or later)
! iPod nano 6th generation (software version
1.0 or later)
! iPod nano 5th generation (software version
1.0.2 or later)
! iPhone 4 (software version 4.1 or later)
! iPhone 3GS (software version 3.0 or later)
! iPhone 3G (software version 3.0 or later)
! iPhone (software version 3.0 or later)
1 Press BAND/
to switch the control mode.
! iPod – This unit’s iPod function can be
operated from the connected iPod.
Section
Operating this unit
Function settings
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following procedures to set the function.
Audiobooks (audiobook speed)
1 Press M.C. to select your favorite setting.
! Faster – Playback at a speed faster than normal
! Normal – Playback at normal speed
! Slower – Playback at a speed slower than normal
Sound Retriever (sound retriever)
1 Press M.C. to select the desired setting.
OFF (off)—1—2
1 is effective for low compression rates, and 2 is
effective for high compression rates.
Shuffle all (shuffle all)
Notes
! Switching the control mode to iPod pauses
song playback. Operate the iPod to resume
playback.
! The following functions are still accessible
from the unit even if the control mode is set to
iPod/APP.
— Pausing
— Fast forward/reverse
— Track up/down
! When the control mode is set to iPod/APP,
only Pause, Tags transfer or
Sound Retriever is available.
! The browse function cannot be operated from
this unit.
1 Press M.C. to turn shuffle all on.
To turn off, set Shuffle mode in the FUNCTION
menu to off.
Using Pandoraâ
Play mode (repeat play)
1 Press M.C. to select a repeat play range.
! Repeat One – Repeat the current song
! Repeat All – Repeat all songs in the selected
list
Shuffle mode (shuffle)
1 Press M.C. to select your favorite setting.
! Shuffle Songs – Play back songs in the selected list in random order.
! Shuffle Albums – Play back songs from a
randomly selected album in order.
! Shuffle OFF – Cancel random play.
Link play (link play)
1 Press M.C. to display the setting mode.
2 Turn M.C. to change the mode; press to select.
For details about the settings, refer to Playing
songs related to the currently playing song on the
previous page.
Pause (pause)
1 Press M.C. to pause or resume.
Tags transfer (Tags transfer)
Transfer the tag information contained in the tuner
source.
1 Press M.C. to store the tag information. Refer to
Using iTunes tagging on page 11.
Operating this unit
! APP – Play back the sound from your
iPod applications.
! AUDIO – This unit’s iPod function can
be operated from this unit.
02
IMPORTANT:
Requirements to access the Pandora music service using the Pioneer car audio/video products:
! Apple iPhone (first generation), iPhone 3G,
iPhone 3GS, iPhone 4G, iPod touch 1G, iPod
touch 2G, iPod touch 3G or iPod touch 4G
(firmware version 3.0 or later).
Certain firmware versions for the iPod touch
and iPhone may not be compatible with the
Pandora application. If this appears to be the
case, please update the firmware to a version
that is compatible with Pandora.
En
17
Section
02
Operating this unit
! Latest version of the Pandora application for
the iPhone, downloaded to your device.
(Search Apple iTunes App Store for
“Pandora”).
! Current Pandora account (Free account and
paid accounts available from Pandora; create
a free account online at
http://www.pandora.com/register or through
the Pandora application for the iPhone).
! iPhone Data Plan.
Note: If the Data Plan for your iPhone does
not provide for unlimited data usage, additional charges from your carrier may apply for
accessing the Pandora service via 3G and/or
EDGE networks.
! Connection to the Internet via 3G, EDGE or WiFi network.
! Optional Pioneer adapter cable connecting
your iPhone to the Pioneer car audio/video
products.
Limitations:
! Access to the Pandora service will depend on
the availability of a cellular and/or Wi-Fi network for purposes of allowing your iPhone to
connect to the Internet.
! Ability of the Pioneer car audio/video products
to access the Pandora service is subject to
change without notice and could be affected
by any of the following: compatibility issues
with future firmware versions of iPhones;
compatibility issues with future firmware versions of the Pandora application for the
iPhone; changes to the Pandora music service
by Pandora; discontinuation of the Pandora
music service by Pandora.
! Certain functionality of the Pandora service is
not available when accessing the service
through the Pioneer car audio/video products,
including, but not limited to, creating new stations, deleting stations, emailing current stations, buying tracks from iTunes, viewing
additional text information, logging in to
Pandora, and adjusting Cell Network Audio
Quality.
Pandora Internet radio is a music service not affiliated with Pioneer. More information is available at http://www.pandora.com.
18
En
You can play the Pandora by connecting your
iPod which was installed the Pandora application.
Notes
! Two iPods can be connected to this unit at the
same time. Settings are the same as those for
Pandora1 and Pandora2.
! If there are two iPods connected to this unit,
the iPod connected to the input of the selected source is the one that is operated.
! Disconnect communications for the selected
iPod before switching to operation of the other
iPod.
Basic operations
12
Thumbs Up/Thumbs Down indicator
QuickMix indicator
PLAY/PAUSE indicator
S.Rtrv indicator
Appears when Sound Retriever function is on.
5 Song time (progress bar)
6 Play time indicator
7 Voltage indicator
Shows the battery voltage.
! The level displayed on the voltage indicator may differ from the actual voltage
level.
Playing tracks
1 Connect an iPod to the USB cable using an iPod
Dock Connector.
2 Start up the Pandora application installed on the
iPod.
Giving a Thumbs Up
to give a “Thumbs Up” for the track cur1 Press
rently playing.
Section
Operating this unit
Skipping tracks
1 Turn LEVER to the right.
1 Press M.C. to pause or resume.
Sound Retriever (sound retriever)
1 Press M.C. to select the desired setting.
1—2—OFF (off)
1 is effective for low compression rates, and 2 is
effective for high compression rates.
Displaying text information
Selecting the desired text information
1 Press /DISP.
Selecting and playing the
QuickMix/station list
1 Press
(list) to switch to the QuickMix/station list mode.
2 Use M.C. to select the QuickMix or desired station.
Changing the sort order
(list).
1 Press
! ABC – You can sort the items in the list alphabetically
! DATE – You can sort the items in the list in order
of the dates on which the items were created
Changing QuickMix or stations
1 Turn M.C.
Playing
1 When QuickMix or the station is selected, press
M.C.
Function settings
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following procedures to set the function.
Audio adjustments
Operating this unit
Giving a Thumbs Down
to give a “Thumbs Down” for the track
1 Press
currently playing and to skip to the next track.
02
Operation modes
This unit features two operation modes: the 3way network mode (NW) and the standard
mode (STD). You can switch between modes
as desired. Initially, the DSP setting is set to
the standard mode (STD). (Refer to Switching
the DSP setting mode on page 5.)
! The 3-way network mode (NW) lets you create a 3-way multi-amp, multi-speaker system with separate speakers for
reproduction of high, middle and low frequencies (bands), each driven by a dedicated power amp. The 3-way network mode
provides network and time alignment functions, two functions essential for a multiamp, multi-speaker system, to enable precise control over settings for each frequency range.
! The standard mode (STD) lets you create a
4-speaker system with front and rear speakers, or a 6-speaker system with front and
rear speakers and subwoofers.
Important
This unit's audio settings will continue to remain
in the memory even if the battery is disconnected
or the microprocessor reset. If you want to reset
the audio settings, refer to AUDIO reset (audio
reset) on page 36.
Operation mode marks
Bookmark (bookmark)
1 Press M.C. to store track information.
This manual uses the following marks to make
the description clear.
Pause (pause)
En
19
Section
02
Operating this unit
: This mark indicates a function only in
3-way network mode or an operation in 3-way
network mode.
: This mark indicates a function available
only in standard mode or an operation in standard mode.
! The functions and operations which do not
carry either mark are commonly used in
the 3-way network mode and standard
mode.
By carrying out the following settings/adjustments in the order shown, you can effortlessly
create a finely-tuned sound field.
3-way network mode
Adjusting the audio easily
By carrying out the following settings/adjustments in the order shown, you can effortlessly
create a finely-tuned sound field.
1 Using the position selector (POSI)
2 Auto TA and EQ (auto-time alignment and autoequalizing)
3 Using balance adjustment (BAL)
4 Recalling equalizer curves
Adjusting the audio finely
By carrying out the following settings/adjustments in the order shown, you can effortlessly
create a finely-tuned sound field.
1 Adjusting time alignment (TA1, TA2)
2 Adjusting network (NW 1, NW 2, NW 3,
NW 4)
3 Adjusting equalizer curves (EQ 1)
4 Adjusting the 16-band graphic equalizer (EQ 2)
Standard mode
Adjusting the audio easily
The following functions let you easily adjust
your audio system to match the car interior
acoustic characteristics, which vary depending on the type of car.
1 Using the position selector (POSI)
2 Auto TA and EQ (auto-time alignment and autoequalizing)
3 Using fader/balance adjustment (F/B)
4 Recalling equalizer curves
20
Adjusting the audio finely
En
Using time alignment (TA1, TA2)
Using subwoofer output (SW 1)
Adjusting subwoofer settings (SW 2)
Adjusting low pass filter attenuation slope
(SW 3)
Setting the high pass filter for front speakers
(F.HPF 1, F.HPF 2)
Setting the high pass filter for rear speakers
(R.HPF 1, R.HPF 2)
Adjusting equalizer curves (EQ 1)
Adjusting the 16-band graphic equalizer (EQ 2)
Extra functions
These functions are helpful in adjusting the
sound to suit your system or your personal
preferences.
! Adjusting loudness (Loudness)
! Adjusting source levels (SLA)
! Using automatic sound levelizer (ASL)
Section
Operating this unit
Introduction of audio adjustments
1 Audio display
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select AUDIO.
3 Turn M.C. to select the audio function.
After selecting, perform the following procedures to set the audio function.
3-way network mode
BAL (balance adjustment)—NW 1 (network
adjustment 1)—NW 2 (network adjustment 2)
—NW 3 (network adjustment 3)—NW 4 (network adjustment 4)—POSI (position selector)
—TA1 (time alignment setting)—TA2 (time
alignment adjusting)—Loudness (loudness)
—EQ 1 (graphic equalizer)—EQ 2 (16-band
graphic equalizer)—A.EQ (auto-equalizer on/
off)—ASL (automatic sound levelizer)—SLA
(source level adjustment)
Standard mode
F/B (balance adjustment)—POSI (position selector)—TA1 (time alignment setting)—TA2
(time alignment adjusting)—Loudness (loudness)—EQ 1 (graphic equalizer)—EQ 2 (16band graphic equalizer)—SW 1 (subwoofer
on/off)—SW 2 (subwoofer cut-off frequency)—
SW 3 (subwoofer slope)—F.HPF 1 (front high
pass filter slope)—F.HPF 2 (front high pass filter cut-off frequency)—R.HPF 1 (rear high
pass filter slope)—R.HPF 2 (rear high pass filter cut-off frequency)—A.EQ (auto-equalizer
on/off)—ASL (automatic sound levelizer)—
SLA (source level adjustment)
Press M.C. to display the setting mode.
# You can also switch between the audio functions in reverse order by turning M.C. counterclockwise.
# When selecting FM as the source, you cannot
switch to SLA.
# When selecting TA OFF in TA1, you cannot
switch to TA2.
# You can select SW 2 and SW 3 only when subwoofer output is turned on in SW 1.
# To return to the display of each source, press
BAND/ .
Operating this unit
02
Notes
! If you do not operate the audio function within
about 30 seconds, the display is automatically
returned to the source display.
! EQ 2 (16-band graphic equalizer), TA2 (time
alignment adjusting), NW 1 (network adjustment 1), NW 2 (network adjustment 2), NW 3
(network adjustment 3) and NW 4 (network
adjustment 4) functions are not canceled
automatically.
Switching left and right channel
You can adjust following functions for left and
right channel independently or commonly.
3-way network mode
! Adjusting network (NW 1, NW 2, NW 3)
! Adjusting the 16-band graphic equalizer
(EQ 2)
Standard mode
! Adjusting subwoofer settings (SW 2)
! Adjusting low pass filter attenuation slope
(SW 3)
! Setting the high pass filter for front speakers
(F.HPF 1, F.HPF 2)
! Setting the high pass filter for rear speakers
(R.HPF 1, R.HPF 2)
! Adjusting the 16-band graphic equalizer
(EQ 2)
1 Use M.C. to select the audio function
described above.
En
21
Section
Operating this unit
02
2 Press M.C. and hold to switch between
left/right common mode and left/right independent mode.
L/R (left/right common mode)—Left (left)—
Right (right)
Adjust these functions as desired.
Using the position selector
One way to assure a more natural sound is to
clearly position the stereo image, putting you
right in the center of the sound field. The position selector function lets you automatically
adjust the speakers’ output levels and inserts
a delay time to match the number and position of occupied seats.
1 Use M.C. to select POSI in the audio
function menu.
Refer to Introduction of audio adjustments on
the previous page.
2 Turn LEVER to select a listening position.
OFF (off)—FL (front seat left)—FR (front seat
right)—Front (front seats)—All (all seats
Using balance adjustment
You can select a balance setting that provides
an ideal listening environment in all occupied
seats.
! This function is only available in 3-way network mode
1 Use M.C. to select BAL.
Refer to Introduction of audio adjustments on
the previous page.
2 Turn LEVER to adjust the left/right
speaker balance.
Left 25 to Right 25 is displayed as the left/
right speaker balance moves from left to right.
22
En
Using fader/balance adjustment
You can change the fader/balance setting to
provide an ideal listening environment for all
of the occupied seats.
! This function is only available in standard
mode
1 Use M.C. to select F/B.
Refer to Introduction of audio adjustments on
the previous page.
2 Turn LEVER to adjust the front/rear
speaker balance.
Front 25 to Rear 25 is displayed as the front/
rear speaker balance moves from front to rear.
# Select F/R 00 when only using two speakers.
3 Press M.C. to display the left/right
speaker balance mode.
4 Turn LEVER to adjust the left/right
speaker balance.
Left 25 to Right 25 is displayed as the left/
right speaker balance moves from left to right.
Using time alignment
The distance between the listening position
and each speaker can be adjusted with this
function.
1 Use M.C. to select TA1 in the audio
function menu.
Refer to Introduction of audio adjustments on
the previous page.
2 Turn LEVER to select the time alignment.
Initial (initial)—Custom (custom)—Auto TA
(auto-time alignment)—TA OFF (off)
! Initial is the factory supplied time alignment.
! Custom is an adjusted time alignment that
you can create for yourself.
! Auto TA is the time alignment created by
auto TA and EQ. (Refer to Auto TA and EQ
(auto-time alignment and auto-equalizing)
on page 29.)
Section
Operating this unit
Adjusting time alignment
The distance between the selected position
and each speaker can be adjusted.
! An adjusted time alignment is memorized
in Custom.
1 Use M.C. to select TA 1.
Refer to Introduction of audio adjustments on
page 21.
2 Press M.C. to select a unit of distance.
(cm) (centimeter)—(inch) (inch)
Press
/DISP to display the upper tier.
4 Use M.C. to select TA2.
Refer to Introduction of audio adjustments on
page 21.
# Can't Adjust TA. Set POS. FL/FR appears
when neither FL nor FR is selected in the position
selector mode (POSI).
# When selecting TA OFF in TA1, you cannot
switch to TA2.
6 Turn LEVER to adjust the distance between the selected speaker and the listening position.
400.0cm to 0.0cm is displayed as the distance
is increased or decreased, if you have selected
centimeters ((cm)).
160inch to 0inch is displayed as the distance
is increased or decreased, if you have selected
inches ((inch)).
# You can adjust the distance for the other
speakers in the same way.
7 Press BAND/
ment mode.
Operating this unit
# You cannot select Auto TA if auto TA and EQ
has not been carried out. In this case,
Please set Auto TA appears.
02
to cancel the time align-
About the network function
The network function lets you divide the audio
signal into different frequency bands, and
then reproduce each of them through separate speaker units.
You can then make precise adjustments to the
reproduced frequency band (with a low-pass
filter or high-pass filter), level, phase and other
parameters to match the characteristics of
each speaker unit.
5 Turn M.C. to select the speaker to be
adjusted.
3-way network mode
High L (high-range left)—High R (high-range
right)—Mid L (middle-range left)—Mid R
(middle-range right)—Low L (low-range left)—
Low R (low-range right)
Standard mode
Front L (front left)—Front R (front right)—
Rear R (rear right)—Rear L (rear left)—
SubW. L (subwoofer left)—SubW. R (subwoofer right)
# You cannot select SubW. L and SubW. R
when the subwoofer output is off.
En
23
Section
02
Operating this unit
Adjustable parameters
The network function enables adjustment of
the following parameters. Make adjustments
in line with the reproduced frequency band
and characteristics of each connected speaker
unit.
Level
(dB)
Points concerning network adjustments
Reproduced frequency band
Pass
Slope (dB/oct.)
Level
Frequency
(Hz)
Cut-off frequency
of HPF
Cut-off frequency
of LPF
Reproduced frequency band
Adjusting the HPF (high-pass filter) or LPF
(low-pass filter) cut-off frequency lets you set
the reproduced frequency band for each
speaker unit.
! The HPF cuts frequencies (low) below the
set frequency, letting high frequencies
through.
! The LPF cuts frequencies (high) above the
set frequency, letting low frequencies
through.
Level
The difference in reproduced levels between
speaker units can be corrected.
Slope
Adjusting the HPF/LPF slope (filter attenuation
slope) lets you adjust the continuity of sound
between speaker units.
! The slope indicates the number of decibels
(dB) the signal is attenuated when the frequency is one octave higher (lower) (Unit:
dB/oct.). The steeper the slope, the more
the signal is attenuated.
24
En
Phase
You can switch phase (normal, reverse) for
each speaker unit’s input signal. When the
continuity of sound between speakers is imprecise, try switching phase. This may improve
the continuity of sound between speakers.
Cut-off frequency adjustment
! With the low-range speaker installed in the
rear tray, if you set Low LPF cut-off frequency high, bass sound is separated so
that it appears to come from the rear. You
are recommended to set Low LPF cut-off
frequency to 100 Hz or lower.
! The maximum input power setting for middle-range and high-range speakers is
usually lower than low-range speakers.
Please be aware that if the Mid HPF or
HighHPF cut-off frequency is set lower
than required, strong bass signal input
may damage the speaker.
Level adjustment
The basic frequencies of many musical instruments are in the middle range. First perform
middle-range level adjustment, followed by
high-range and then low-range level adjustment in that order.
Slope adjustment
! If you set a small absolute value for the
slope (for a gentle slope), interference between adjacent speaker units can easily result in degraded frequency response.
! If you set a large absolute value for the
slope (for a steep slope), continuity of
sound between speaker units is degraded,
and sounds appear to be separated.
! If you set the slope to 0 dB/oct. (pass), the
audio signal bypasses the filter, so the filter
does not have an effect.
Section
Operating this unit
Normal phase
Reverse phase
Crossover point
Muting the speaker unit (filter)
You can mute each speaker unit (filter). When
a speaker unit (filter) is muted, no sound is
outputted from that speaker.
! If you mute the selected speaker unit (filter), MUTE blinks and no adjustments are
possible.
! Even if any speaker unit (filter) is muted,
you can adjust the parameters for other
speaker units (filters).
1 Use M.C. to select NW 1.
Refer to Introduction of audio adjustments on
page 21.
2 Turn LEVER to select the speaker unit
(filter) to be adjusted.
Low LPF (low-range speaker LPF)—Mid HPF
(middle-range speaker HPF)—Mid LPF (middle-range speaker LPF)—HighHPF (high-range
speaker HPF)
3 Press M.C. to mute the selected speaker
unit (filter).
MUTE blinks in the display.
# To cancel the muting, press M.C. again.
Adjusting network
1 Use M.C. to select NW 1.
Refer to Introduction of audio adjustments on
page 21.
2 Turn LEVER to select the speaker unit
(filter) to be adjusted.
Low LPF (low-range speaker LPF)—Mid HPF
(middle-range speaker HPF)—Mid LPF (middle-range speaker LPF)—HighHPF (high-range
speaker HPF)
Press
/DISP to display the upper tier.
4 Use M.C. to select NW 2.
Refer to Introduction of audio adjustments on
page 21.
Operating this unit
Phase adjustment
When the cross-over point value for filters on
both sides is set to –12 dB/oct., the phase is
reversed 180 degrees at the filter cut-off frequency. In this case, reversing the phase assures improved sound continuity.
02
5 Turn M.C. to select the cut-off frequency (crossover frequency) of the selected speaker unit (filter).
Low LPF: 25—31.5—40—50—63—80—100
—125—160—200—250 (Hz)
Mid HPF: 25—31.5—40—50—63—80—100
—125—160—200—250 (Hz)
Mid LPF: 1.25k—1.6k—2k—2.5k—3.15k—
4k—5k—6.3k—8k—10k—12.5k (Hz)
HighHPF: 1.25k—1.6k—2k—2.5k—3.15k—
4k—5k—6.3k—8k—10k—12.5k (Hz)
6 Turn LEVER to adjust the level of the selected speaker unit (filter).
±0dB to –24dB is displayed as the level is increased or decreased.
+6dB to –24dB is displayed as the level is increased or decreased, only if you have selected Low LPF.
Press
/DISP to display the upper tier.
8 Use M.C. to select NW 3.
Refer to Introduction of audio adjustments on
page 21.
9 Turn LEVER to select the slope of the selected speaker unit (filter).
Low LPF: –36— –30— –24— –18— –12 (dB/
oct.)
Mid HPF: –24— –18— –12— –6—Pass (0)
(dB/oct.)
Mid LPF: –24— –18— –12— –6—Pass (0)
(dB/oct.)
HighHPF: –24— –18— –12— –6 (dB/oct.)
En
25
Section
02
Operating this unit
10 Press M.C. to switch the phase of the
selected speaker unit (filter).
NOR (normal)—REV (reverse)
# You can adjust the parameters for other
speaker units (filters) in the same way.
11 Press
/DISP to display the upper tier.
12 Use M.C. to select NW 4.
Refer to Introduction of audio adjustments on
page 21.
13 Press M.C. to select stereo or monaural.
Stereo (stereo)—MONO (monaural)
# You can operate this procedure only when
Low LPF is selected.
14 Press BAND/ to cancel the network
adjustment mode.
Adjusting subwoofer settings
The cut-off frequency and output level can be
adjusted when the subwoofer output is on.
1 Use M.C. to select SW 2.
Refer to Introduction of audio adjustments on
page 21.
# When the subwoofer output is on, you can select SW 2.
2 Turn M.C. to select cut-off frequency.
50—63—80—100—125 (Hz)
Only frequencies lower than those in the selected range are outputted from the subwoofer.
3 Turn LEVER to adjust the output level
of the subwoofer.
+6 to -24 is displayed as the level is increased
or decreased.
Using subwoofer output
This unit is equipped with a subwoofer output
which can be turned on or off. When a subwoofer is connected to this unit, turn the subwoofer output on.
The subwoofer output phase can be switched
between normal and reverse.
! This function is only available in standard
mode
Adjusting low pass filter attenuation
slope
1 Use M.C. to select SW 1.
Refer to Introduction of audio adjustments on
page 21.
# When the subwoofer output is on, you can select SW 3.
2 Press M.C. to turn subwoofer output
on.
ON appears in the display. Subwoofer output
is now on.
# To turn subwoofer output off, press M.C.
again.
3 Turn LEVER to select stereo or monaural.
Stereo (stereo)—MONO (monaural)
26
En
When the subwoofer output is on, you can adjust the continuity of sound between speaker
units.
1 Use M.C. to select SW 3.
Refer to Introduction of audio adjustments on
page 21.
2 Press M.C. to select the phase of subwoofer output.
NOR (normal)—REV (reverse)
3 Turn LEVER to select slope.
–18— –12— –6 (dB/oct.)
Note
When slope of subwoofer and high pass filter are
-12dB, and same cut-off frequency, the phase is
reversed 180 degrees at the cut-off frequency. In
this case, reversing the phase assures improved
sound continuity.
Section
Operating this unit
Using the high pass filter
Muting the speaker units (filters)
You can mute front and rear speaker units (filters) separately. When speaker units (filters)
are muted, no sound is outputted from those
speakers.
! Even if the speaker unit (filter) is muted,
you can adjust the muted speaker units (filters). However, mute is automatically canceled when the level is adjusted.
1 Use M.C. to select F.HPF 1 (or R.HPF 1).
Refer to Introduction of audio adjustments on
page 21.
2 Press M.C. to mute the selected speaker
unit (filter).
MUTE is displayed.
# To cancel the muting, press M.C. again.
Setting the high pass filter for front
speakers
1 Use M.C. to select F.HPF 1.
Refer to Introduction of audio adjustments on
page 21.
2 Turn LEVER to select slope.
–12— –6—Pass (dB/oct.)
# If you set the slope Pass (0 dB/oct.), the audio
signal bypasses the filter, so the filter does not
have an effect.
Press
/DISP to display the upper tier.
4 Use M.C. to select F.HPF 2.
Refer to Introduction of audio adjustments on
page 21.
5 Turn M.C. to select cut-off frequency.
50—63—80—100—125—160—200 (Hz)
Only frequencies higher than those in the selected range are output from the front speakers.
6 Turn LEVER to adjust the output level
of the front speakers.
0 to –24 is displayed as the level is increased
or decreased.
Setting the high pass filter for rear
speakers
Operating this unit
When you do not want low sounds from the
subwoofer output frequency range to play
from the front or rear speakers, turn on the
HPF (high pass filter). Only frequencies higher
than those in the selected range are output
from the front or rear speakers.
! This function is only available in standard
mode
02
1 Use M.C. to select R.HPF 1.
Refer to Introduction of audio adjustments on
page 21.
2 Turn LEVER to select slope.
–12— –6—Pass (dB/oct.)
# If you set the slope Pass (0 dB/oct.), the audio
signal bypasses the filter, so the filter does not
have an effect.
Press
/DISP to display the upper tier.
4 Use M.C. to select R.HPF 2.
Refer to Introduction of audio adjustments on
page 21.
5 Turn M.C. to select cut-off frequency.
50—63—80—100—125—160—200 (Hz)
Only frequencies higher than those in the selected range are output from the rear speakers.
6 Turn LEVER to adjust the output level
of the rear speakers.
+6 to –24 is displayed as the level is increased
or decreased.
Using the auto-equalizer
The auto-equalizer is the equalizer curve created by auto TA and EQ (refer to Auto TA and
EQ (auto-time alignment and auto-equalizing)
on page 29).
You can turn the auto-equalizer on or off.
En
27
Section
02
Operating this unit
1 Use M.C. to select A.EQ in the audio
function menu.
Refer to Introduction of audio adjustments on
page 21.
# If auto TA and EQ has not been carried out,
Please set Auto EQ appears. This indicates that
you cannot turn this function on.
2 Press M.C. to turn the auto-equalizer
on.
Auto EQ ON appears in the display.
# To turn auto-equalizer off, press M.C. again.
Recalling equalizer curves
You can adjust the equalization to match the
car’s interior acoustic characteristics as desired.
There are seven stored equalizer curves which
you can easily recall at any time. Here is a list
of the equalizer curves.
Display
Equalizer curve
Super bass
Super bass
Powerful
Powerful
Natural
Natural
Vocal
Vocal
Flat
Flat
Custom1
Custom 1
Custom2
Custom 2
! Custom1 and Custom2 are adjusted equalizer curves that you create. Adjustments
can be made with a 16-band graphic equalizer.
! When Flat, no changes are made to the
sound. You can check the effects of the
equalizer curves by switching alternatively
between Flat and another equalizer curve.
% Press EQ/DISP OFF to select the equalizer.
Press EQ/DISP OFF repeatedly to switch between the following equalizers:
Powerful—Natural—Vocal—Flat—Custom1
—Custom2—Super bass
28
En
Adjusting equalizer curves
The factory supplied equalizer curves, with the
exception of Flat, can be adjusted to a fine degree (nuance control).
1 Use M.C. to select EQ 1.
Refer to Introduction of audio adjustments on
page 21.
Turn M.C. to select an equalizer curve.
3 Turn LEVER to adjust the equalizer
curve.
+6 to –6 is displayed as the equalizer curve is
increased or decreased.
# The actual range of the adjustments are different depending on which equalizer curve is selected.
# The equalizer curve with all frequencies set to
0 cannot be adjusted.
Adjusting the 16-band graphic
equalizer
You can adjust the level of each band for the
Custom1 and Custom2 equalizer curves.
! A separate Custom1 curve can be created
for each source. If you make adjustments
when a curve other than Custom2 is selected, the equalizer curve settings will be
recorded in Custom1.
! A Custom2 curve that is common for all
sources can be created. If you make adjustments when the Custom2 curve is selected, the Custom2 curve will be updated.
1 Recall the equalizer curve you want to
adjust.
Refer to Recalling equalizer curves on this
page.
2 Use M.C. to select EQ 2.
Refer to Introduction of audio adjustments on
page 21.
Section
Operating this unit
4 Turn LEVER to adjust the level of the
equalizer band.
+6 to –6 is displayed as the level is increased
or decreased.
# You can then select another band and adjust
the level.
5 Press BAND/ to cancel the 16-band
graphic equalizer adjustment.
Adjusting loudness
Loudness compensates for deficiencies in the
low-frequency and high-frequency ranges at
low volume.
1 Use M.C. to select Loudness in the
audio function menu.
Refer to Introduction of audio adjustments on
page 21.
Press M.C. to turn loudness on.
# To turn loudness off, press M.C. again.
Adjusting source levels
With SLA (source level adjustment), the volume levels of each source can be adjusted to
prevent significant differences between
sources.
! Settings are based on the FM volume level,
which remains unchanged.
1 Compare the FM volume level with the
level of the source you wish to adjust.
2 Use M.C. to select SLA in the audio
function menu.
Refer to Introduction of audio adjustments on
page 21.
3 Turn LEVER to adjust the source volume.
+4 to –4 is displayed as the source volume is
increased or decreased.
Notes
! The AM volume level can also be adjusted
with this function.
! The USB/SD volume level can also be adjusted with this function.
Using automatic sound levelizer
Operating this unit
3 Turn M.C. to select the equalizer band
to adjust.
20—31.5—50—80—125—200—315—500—
800—1.25k—2k—3.15k—5k—8k—12.5k—
20k (Hz)
02
During driving, noise in the car changes according to the driving speed and road conditions. The automatic sound levelizer (ASL)
monitors such varying noise and automatically increases the volume level, if this noise
becomes greater. The sensitivity (variation of
volume level to noise level) of ASL can be set
to one of five levels.
1 Use M.C. to select ASL.
Refer to Introduction of audio adjustments on
page 21.
Press M.C. to turn ASL on.
# To turn ASL off, press M.C. again.
3 Turn LEVER to select the desired ASL
level.
Low (low)—Mid-L (mid-low)—Mid (mid)—
Mid-H (mid-high)—High (high)
Auto TA and EQ (auto-time
alignment and auto-equalizing)
Auto-time alignment automatically adjusts the
time alignment according to the distance between the listening position and each speaker.
The auto-equalizer automatically measures
the car’s interior acoustic characteristics, and
then creates an auto-equalizer curve based on
that information.
En
29
Section
02
Operating this unit
WARNING
As a loud tone (noise) may be emitted from the
speakers when measuring the car’s interior
acoustic characteristics, never perform auto TA
or auto EQ while driving.
CAUTION
! Thoroughly check the conditions before performing auto TA and EQ as the speakers may
be damaged if these functions are performed
when:
— The speakers are incorrectly connected.
(For example, when a rear speaker is connected as a subwoofer output.)
— A speaker is connected to a power amp delivering output higher than the speaker’s
maximum input power capability.
! If the microphone is placed in an unsuitable
position the measurement tone may become
loud and measurement may take a long time,
resulting in battery drainage. Be sure to place
the microphone in the specified location.
Before operating the auto TA and EQ
function
! Perform auto TA and EQ in a quiet place,
with both the car engine and air conditioning switched off. Also turn off any car
phones or portable telephones in the car, or
remove them from the car. Sounds other
than the measurement tone (such as surrounding sounds, engine sound, telephones ringing) may prevent correct
measurement of the car’s interior acoustic
characteristics.
! Be sure to perform auto TA and EQ using
the supplied microphone. Using another
microphone may prevent measurement, or
result in incorrect measurement of the
car’s interior acoustic characteristics.
! In order to perform auto TA and EQ, the
front speaker must be connected.
! When muting the front speaker units, auto
TA and EQ cannot be carried out. (Refer to
page 27.)
30
En
! When this unit is connected to a power
amp with input level control, auto TA and
EQ may not be possible if the power amp’s
input level is set below the standard level.
! When this unit is connected to a power
amp with an LPF, turn this LPF off before
performing auto TA and EQ. Also set the
cut-off frequency for the built-in LPF of an
active subwoofer to the highest frequency.
! The time alignment value resulting from
auto TA and EQ has been calculated by a
computer and is the optimum delay time
that will give accurate results. Be sure to
use the resulting value although it may differ from the actual distance when:
— The reflected sound within the car is
strong and delays occur.
— The LPF on active subwoofers or external amps delay the lower sounds.
! Auto TA and EQ changes the audio settings
as follows:
— The fader/balance settings return to the
center position. (Refer to Using fader/
balance adjustment on page 22.)
— The graphic equalizer curve switches to
Flat. (Refer to page 28.)
— When a subwoofer is connected to this
unit, it will be adjusted automatically to
both subwoofer output and high pass filter setting for rear speaker.
! Previous settings for auto TA and EQ will be
overwritten.
! When connecting tweeters, please confirm
the tweeter’s usable frequency range.
When you set the cut-off frequency, set
higher than the lowest usable frequency of
the tweeter.
! Auto TA uses higher range than 10 kHz for
measurement. Therefore, using the tweeter
that cannot reproduce 10 kHz frequency
range may damage the tweeter. When auto
TA and EQ is operated, be sure to set the
appropriate cut-off frequency. Also, use the
tweeter that can reproduce 10 kHz at the
lowest usable frequency.
Section
Operating this unit
Performing auto TA and EQ
7 Plug the microphone into the microphone input jack on this unit.
# If the engine is left running, the noise from
the engine may cause incorrect auto TA and EQ.
2 Fix the supplied microphone in the center of the headrest of the driver’s seat, facing forward.
Press M.C. to start the auto TA and EQ.
Operating this unit
1 Stop the car in a place that is quiet,
close all the doors, windows and sun roof,
and then turn the engine off.
02
9 When the 10-second countdown starts,
get out of the car and close the door within
10 seconds.
The measurement tone (noise) is outputted
from the speakers, and auto TA and EQ begins.
# The auto TA and EQ may differ depending on
where you place the microphone. If desired, place
the microphone on the front passenger seat to
perform auto TA and EQ.
Turn the ignition switch to ON or ACC.
# If the air conditioner or heater is turned on,
turn it off. The noise from the fan may cause incorrect auto TA and EQ.
# Press SRC/OFF to turn the source on if this
unit is turned off.
4 Select the position for the seat on
which the microphone is placed.
Refer to Using the position selector on page
22.
# If no position is selected before auto TA and
EQ is started, FL is automatically selected.
5 Press SRC/OFF and hold until the unit
turns off.
# When all speakers are connected, auto TA
and EQ is completed in about six minutes.
# To stop auto TA and EQ, press M.C. again.
# To cancel auto TA and EQ part way through,
press BAND/ .
10 When auto TA and EQ is completed,
Complete is displayed.
When correct measurement of car interior
acoustic characteristics is not possible, an
error message is displayed. (Refer to Auto TA
and EQ on page 44.)
11 Press BAND/
and EQ mode.
to cancel the auto TA
12 Store the microphone carefully in the
glove compartment or another safe place.
If the microphone is subjected to direct sunlight for an extended period, high temperatures may cause distortion, color change or
malfunction.
6 Press and hold EQ/DISP OFF to enter
the auto TA and EQ measurement mode.
The front panel opens automatically.
En
31
Section
02
Operating this unit
Using Bluetooth wireless
technology
Using Bluetooth telephone
Important
! Since this unit is on standby to connect with
your cellular phone via Bluetooth wireless
technology, using it without the engine running can drain the battery power.
! Operations may vary depending on the kind of
cellular phone.
! Advanced operations that require attention
such as dialing numbers on the monitor,
using the phone book, etc., are prohibited
while driving. Park your vehicle in a safe place
when using these advanced operations.
Setting up for hands-free phoning
Before you can use the hands-free phoning
function you must set up the unit for use with
your cellular phone.
1 Connection
Operate the Bluetooth telephone connection
menu. Refer to Connection menu operation on
this page.
2 Function settings
Operate the Bluetooth telephone function menu.
Refer to Phone menu operation on page 35.
Answering an incoming call
1 When a call is received, press M.C.
Ending a call
1 Press
Answering a call waiting
1 When a call is received, press M.C.
32
En
Turning private mode on or off
1 Press BAND/ while talking on the phone.
Switching the information display
1 Press /DISP while talking on the phone.
Notes
! If private mode is selected on the cellular
phone, hands-free phoning may not be available.
! The estimated call time appears in the display
(this may differ slightly from the actual call
time).
Connection menu operation
Important
! Be sure to park your vehicle in a safe place
and apply the parking brake when performing
this operation.
! Connected devices may not operate properly if
more than one Bluetooth device is connected
at a time (e.g. a phone and a separate audio
player are connected simultaneously).
to display the con-
# You cannot operate this step during a call.
Making a phone call
! Refer to Phone menu operation on page 35.
Switching between callers on hold
1 Press M.C.
Adjusting the other party’s listening volume
1 Turn LEVER while talking on the phone.
! When private mode is on, this function is not
available.
1 Press and hold
nection menu.
Basic operations
Rejecting an incoming call
1 When a call is received, press
Canceling call waiting
1 Press
2 Turn M.C. to select the function.
After selecting, perform the following procedures to set the function.
Section
Operating this unit
Device list (connecting or disconnecting a device
from the device list)
When no device is selected in the device list, this
function is not available.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the name of a device you want
to connect/disconnect.
! Press and hold M.C. to switch the Bluetooth
device address and device name.
3 Press M.C. to connect/disconnect the selected device.
Once the connection is established, Connected
is displayed.
Delete device (deleting a device from the device list)
When no device is selected in the device list, this
function is not available.
Press M.C. to display the setting mode.
Turn M.C. to select the name of a device you want
to delete.
! Press and hold M.C. to switch the Bluetooth
device address and device name.
Press M.C. to display Delete YES.
Press M.C. to delete a device information from
the device list.
While this function is in use, do not turn off the
engine.
Add device (connecting a new device)
1 Press M.C. to start searching.
! To cancel, press M.C. while searching.
! If this unit fails to find any available cellular
phones, Not found is displayed.
2 Turn M.C. to select a device from the device list.
! Press and hold M.C. to switch the Bluetooth
device address and device name.
3 Press M.C. to connect the selected device.
! To complete the connection, check the device
name (Pioneer BT Unit). Enter the PIN code
on your device if necessary.
! PIN code is set to 0000 as the default. You
can change this code.
! 6-digit number appears on the display of this
unit. Once the connection is established, this
number disappears.
! If you are unable to complete the connection
using this unit, use the device to connect to
the unit.
! If three devices are already paired, Device Full
is displayed and it is not possible to perform
this operation. In this case, delete a paired device first.
Special device (setting a special device)
Bluetooth devices that are difficult to establish a connection with are called special devices. If your
Bluetooth device is listed as a special device, select
the appropriate one.
1 Press M.C. to display the setting mode.
! If three devices are already paired, Device Full
is displayed and it is not possible to perform
this operation. In this case, delete a paired device first.
2 Turn M.C. to display a special device. Press to select.
3 Turn M.C. to display this unit’s device name,
Bluetooth device address and PIN code.
4 Use a device to connect to this unit.
! To complete the connection, check the device
name (Pioneer BT Unit) and enter the PIN
code on your device.
! PIN code is set to 0000 as the default. You
can change this code.
Operating this unit
02
Auto connect (connecting to a Bluetooth device
automatically)
1 Press M.C. to turn automatic connection on or
off.
Visibility (setting the visibility of this unit)
To check the availability of this unit from other devices, Bluetooth visibility of this unit can be turned
on.
1 Press M.C. to turn the visibility of this unit on or
off.
! While setting Special device, Bluetooth visibility of this unit is turned on temporarily.
Pin code input (PIN code input)
To connect your device to this unit via Bluetooth wireless technology, you need to enter a PIN code on your
device to verify the connection. The default code is
0000, but you can change it with this function.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select a number.
3 Press M.C. to move the cursor to the next position.
4 After inputting PIN code, press and hold M.C.
! After inputting, pressing M.C. returns you to
the PIN code input display, and you can
change the PIN code.
En
33
Section
02
Operating this unit
Device INFO (Bluetooth device address display)
1 Press M.C. to display the setting mode.
2 Turn M.C. left to switch to the Bluetooth device
address.
Turning M.C. right returns to the device name.
Bluetooth Audio
Important
! Depending on the Bluetooth audio player connected to this unit, the available operations
will be limited to the following two levels:
— A2DP profile (Advanced Audio Distribution
Profile): You can only playback songs on
your audio player.
— AVRCP profile (Audio/Video Remote Control Profile): You can perform playback,
pause playback, select songs, etc.
! Since there are a number of Bluetooth audio
players available on the market, available operations will vary extensively. When operating
your player with this unit, refer to the instruction manual that came with your Bluetooth
audio player as well as this manual.
! Information related to a song (such as the
elapsed playing time, song title, song index,
etc.) cannot be displayed on this unit.
! As the signal from your cellular phone may
cause noise, avoid using it when you are listening to songs on your Bluetooth audio
player.
! When a call is in progress on the cellular
phone connected to this unit via Bluetooth
wireless technology, the sound of the
Bluetooth audio player connected to this unit
is muted.
! When the Bluetooth audio player is in use,
you cannot connect to a Bluetooth telephone
automatically.
! Playback continues even if you switch from
your Bluetooth audio player to another source
while listening to a song.
34
En
Setting up for Bluetooth audio
Before you can use the Bluetooth audio function you must set up the unit for use with your
Bluetooth audio player. This entails establishing a Bluetooth wireless connection between
this unit and your Bluetooth audio player, and
pairing your Bluetooth audio player with this
unit.
Basic operations
1 Device name
Shows the device name of the connected
Bluetooth audio player.
2 Voltage indicator
Shows the battery voltage.
! The level displayed on the voltage indicator may differ from the actual voltage
level.
Fast forwarding or reversing
1 Turn and hold down LEVER to the right or left.
Selecting a track
1 Turn LEVER.
Starting playback
1 Press BAND/ .
Function settings
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
After selecting, perform the following procedures to set the function.
Section
Operating this unit
Play (play)
02
1 Press M.C. to stop the playback.
Pause (pause)
1 Press M.C. to turn pause on.
Phone menu operation
Important
Be sure to park your vehicle in a safe place and
apply the parking brake when performing this operation.
Press
to display the phone menu.
2 Turn M.C. to select the function.
After selecting, perform the following procedures to set the function.
Missed calls (missed call history)
Dialed calls (dialed call history)
Received calls (received call history)
Press M.C. to display the phone number list.
Turn M.C. to select a name or phone number.
Press M.C. to make a call.
To display details about the contact you selected,
press and hold M.C.
PhoneBook (phone book)
Operating this unit
1 Press M.C. to start playback.
Stop (stop)
The phone book in your cellular phone will be
transferred automatically when the phone is connected to this unit.
Depending on the cellular phone, the phone book
may not be transferred automatically. In this case,
operate your cellular phone to transfer the phone
book. The visibility of this unit should be on. Refer
to Visibility (setting the visibility of this unit) on
page 33.
Press M.C. to display SEARCH (alphabetical list).
Turn M.C. to select the first letter of the name you
are looking for.
! Press and hold M.C. to select the desired
character type.
Press M.C. to display a registered name list.
Turn M.C. to select the name you are looking for.
Press M.C. to display the phone number list.
Turn M.C. to select a phone number you want to
call.
Press M.C. to make a call.
Phone Function (phone function)
You can set Auto answer, Ring tone and PH.B.
Name view from this menu. For details, refer to Function and operation on this page.
Function and operation
1 Display Phone Function.
Refer to Phone Function (phone function) on
this page.
2 Press M.C. to display the function
menu.
3 Turn M.C. to select the function.
After selecting, perform the following procedures to set the function.
Auto answer (automatic answering)
1 Press M.C. to turn automatic answering on or off.
Ring tone (ring tone select)
1 Press M.C. to turn the ring tone on or off.
PH.B.Name view (phone book name view)
1 Press M.C. to switch between the lists of names.
En
35
Section
02
Operating this unit
Initial settings
When operating external storage devices (USB, SD),
you can select files from the list.
1 Press M.C. to select the setting.
OFF—USB memory1—USB memory2—SD card
Warning tone (warning tone setting)
1 Function display
! Shows the function status.
1 Press and hold SRC/OFF until the unit
turns off.
2 Press M.C. and hold until the initial setting menu appears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following procedures to set the initial setting.
Language select (multi-language)
If the front panel is not detached from the head unit
within four seconds of turning off the ignition, a warning tone sounds. You can turn off the warning tone.
1 Press M.C. to turn the warning tone on or off.
AUX1 (front AUX input setting)/AUX2 (rear RCA
input setting)
Activate this setting when using an auxiliary device
connected to this unit.
1 Press M.C. to turn auxiliary setting on or off.
Dimmer (dimmer setting)
To prevent the display from being too bright at night,
the display is automatically dimmed when the car’s
headlights are turned on. You can turn the dimmer on
or off.
1 Press M.C. to turn dimmer on or off.
Contrast (display contrast setting)
For your convenience, this unit equips multiple language display. You can select the language best suited to your first language.
1 Press M.C. to select the language.
English—Français—Español
1 Press M.C. to select the setting mode.
2 Turn M.C. to adjust the contrast level.
0 to 15 is displayed as the level is increased or decreased.
Calendar (setting the date)
Digital ATT (digital attenuator)
1 Press M.C. to select the segment of the calendar
display you wish to set.
Year—Day—Month
2 Turn M.C. to set the date.
When listening to a CD or other source on which the
recording level is high, setting the equalizer curve
level to high may result in distortion. You can switch
the digital attenuator to low to reduce distortion.
! Sound quality is better at the high setting so this
setting is usually used.
1 Press M.C. to select the setting.
HIGH (high)—LOW (low)
Clock (setting the clock)
1 Press M.C. to select the segment of the clock display you wish to set.
Hour—Minute
2 Turn M.C. to adjust the clock.
EngineTime alert (elapsed time display setting)
This setting allows you to measure the length of time
that elapses from when the machine is turned on and
display the amount of elapsed time per set period.
Also, you will hear alarm.
1 Press M.C. to select your favorite setting.
OFF—15Minutes—30Minutes
Music browse (music browse)
AUDIO reset (audio reset)
You can reset all audio functions.
1 Press M.C.
Does it RESET? appears in the display.
2 Press M.C.
3 Turn M.C. to select desired setting.
Are You Sure? appears in the display.
4 Press M.C.
Complete appears in the display and audio functions are reset.
! To cancel this function on the way, press BAND/
Internal AMP (power amp setting)
36
En
Section
Operating this unit
S/W UPDATE (updating the bluetooth software)
This function is used to update this unit with the latest bluetooth software. For about bluetooth software
and updating, refer to our website.
! Never turn the unit off while the bluetooth software is being updated.
1 Press M.C. to display the data transfer mode.
Follow the on-screen instructions to finish updating the bluetooth software.
Demonstration (demo display setting)
1 Press M.C. to turn the demo display on or off.
Ever-scroll (scroll mode setting)
Other functions
When ever scroll is set to ON, recorded text information scrolls continuously in the display. Set to OFF if
you prefer the information to scroll just once.
1 Press M.C. to turn the ever scroll on or off.
Using AUX1 and AUX2 source
BT AUDIO (Bluetooth audio activation)
You need to activate the BT Audio source in order to
use a Bluetooth audio player.
1 Press M.C. to turn the BT Audio source on or off.
Clear memory (resetting the Bluetooth wireless technology module)
Bluetooth device data can be deleted. To protect personal information, we recommend deleting this data
before transferring the unit to other persons. The following settings will be deleted.
! phone book entries on the Bluetooth telephone
! preset numbers on the Bluetooth telephone
! registration assignment of the Bluetooth telephone
! call history of the Bluetooth telephone
! information of the connected Bluetooth telephone
! PIN code of the Bluetooth device
1 Press M.C. to show the confirmation display.
YES is displayed. Clearing memory is now on
standby.
If you do not want to reset phone memory, turn
M.C. to display CANCEL and press to select.
2 Press M.C. to clear the memory.
Cleared is displayed and the settings are deleted.
! While this function is in use, do not turn off
the engine.
BT Version info. (Bluetooth version display)
You can display the system versions of this unit and
of Bluetooth module.
Operating this unit
This unit features high power amplifier. However, in
particular system, external amplifiers are used instead of internal amplifier. If you use external amplifiers in order to establish a multi-amp system, and
don't use internal amplifier, it is recommended to turn
off the internal amplifier. Turning off internal amplifier
reduces the noise that comes from the behavior of internal amplifier.
1 Press M.C. to turn the internal power amplifier on
or off.
02
About AUX1 and AUX2
There are two methods to connect auxiliary devices to this unit.
AUX1 source
When connecting auxiliary device using the
front AUX input.
! You need to activate the AUX setting in the
initial setting menu. Refer to AUX1 (front
AUX input setting)/AUX2 (rear RCA input
setting) on the previous page.
1 Insert the mini plug into the AUX input
jack on this unit.
For more details, refer to Head unit on page 7.
This auxiliary device is automatically set to
AUX1.
2 Press SRC/OFF to select AUX1 as the
source.
AUX2 source
When connecting auxiliary device using the
rear RCA input.
! You need to activate the AUX setting in the
initial setting menu. Refer to AUX1 (front
AUX input setting)/AUX2 (rear RCA input
setting) on the previous page.
En
37
Section
Operating this unit
02
1 Use the rear RCA input to connect an
auxiliary device.
For more details, refer to the installation manual.
This auxiliary device is automatically set to
AUX2.
2 Press SRC/OFF to select AUX2 as the
source.
Using different entertainment
displays
You can enjoy entertainment displays while listening to each sound source.
Selecting the illumination color
This unit is equipped with multiple-color illumination. You can select desired colors for the
keys and display of this unit. You also can customize the colors you want to use.
Selecting the key color from the
illumination color list
You can select desired colors for the keys of
this unit.
Switching the display indication
2 Turn M.C. to change the menu option
and press to select ILLUMI.
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select ENTERTAINMENT.
Turn M.C. to select the function.
Press M.C. to display the Background.
5 Turn M.C. to change the display.
Background visual—genre—background picture 1—background picture 2—background
picture 3—background picture 4—spectrum
analyzer1—spectrum analyzer2—level indicator—level meter—simple display—movie
screen —calendar
# Genre display changes depending on the
genre of music.
# Genre display may not operate correctly depending on the application used to encode audio
files.
Turning the clock display on or off
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select ENTERTAINMENT.
3 Turn M.C. to select the function.
Select the clock setting.
38
4 Press M.C. to select the desired setting.
Clock display—elapsed time display—clock
off
En
Press M.C. to display the main menu.
3 Turn M.C. to display Key and press to
select.
4 Turn M.C. to select the illumination
color.
You can select one option from the following
list.
! 27 preset colors (WHITE to ROSE)
! SCAN (cycle through all colors)
! Three sets of colors (WARM, AMBIENT,
CALM)
! CUSTOM (customized illumination color)
Notes
! When SCAN is selected, the system automatically cycles through the 27 preset colors.
! When WARM is selected, the system automatically cycles through the warm colors.
! When AMBIENT is selected, the system automatically cycles through the ambient colors.
! When CALM is selected, the system automatically cycles through the calm colors.
! When CUSTOM is selected, the customized
color saved is selected.
Section
Operating this unit
02
! Three sets of colors (WARM, AMBIENT,
CALM)
Selecting the display color from the
illumination color list
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select ILLUMI.
3 Turn M.C. to switch to Display and
press to select.
4 Turn M.C. to select the illumination
color.
You can select one option from the following
list.
! 27 preset colors (WHITE to ROSE)
! SCAN (cycle through all colors)
! Three sets of colors (WARM, AMBIENT,
CALM)
! CUSTOM (customized illumination color)
Note
For details about colors on the list, refer to Selecting the key color from the illumination color list on
the previous page.
Selecting key and display color from
the illumination color list
You can select the desired colors for the keys
and display of this unit.
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select ILLUMI.
3 Turn M.C. to display Key & Display and
press to select.
4 Turn M.C. to select the illumination
color.
You can select one option from the following
list.
Notes
! You cannot select CUSTOM in this function.
! Once you select a color in this function, colors
on the keys and display of this unit automatically switch to the color you selected.
! For details about colors on the list, refer to Selecting the key color from the illumination color
list on the previous page.
Operating this unit
You can select the desired colors for the display of this unit.
Customizing the illumination color
Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select ILLUMI.
3 Turn M.C. to display Key or Display.
Press to select.
4 Press M.C. and hold until the customizing illumination color setting appears in
the display.
5 Press M.C. to select the primary color.
R (red)—G (green)—B (blue)
6 Turn M.C. to adjust the brightness level.
Adjustment range: 0 to 60
# You cannot select a level below 20 for all three
of R (red), G (green), and B (blue) at the same
time.
# You can also perform the same operation on
other colors.
Notes
! You cannot create a custom illumination color
when SCAN or a set of colors (WARM,
AMBIENT, or CALM) is selected.
! You can create custom illumination colors for
both Key and Display.
! 27 preset colors (WHITE to ROSE)
! SCAN (cycle through all colors)
En
39
Section
02
Operating this unit
Switching the display
indication and button
illumination
Display indication and button illumination can
be switched on or off.
% Press and hold EQ/DISP OFF.
Pressing and holding EQ/DISP OFF switches
the display indication and button illumination
on or off.
# Even if the display indication is turned off, operation can be conducted. If operation is conducted while the display indication is off, display
will light up for a few seconds and then turn off
again.
40
En
Appendix
Additional information
Troubleshooting
Symptom
Cause
Action
The display
automatically
returns to the
ordinary display.
You did not per- Perform operation
form any opera- again.
tion within about
30 seconds.
The repeat play Depending on
Select the repeat
range changes the repeat play
play range again.
unexpectedly. range, the selected range may
change when another folder or
track is being selected or during
fast forwarding/
reversing.
A subfolder is
not played
back.
Subfolders can- Select another renot be played
peat play range.
when Folder repeat (folder repeat) is selected.
The unit is malfunctioning.
There is interference.
You are using a
device, such as a
cellular phone,
that transmits
electric waves
near the unit.
Move electrical devices that may be
causing the interference away from
the unit.
The sound
from the
Bluetooth
audio source is
not played
back.
There is a call in
progress on a
Bluetooth connected cellular
phone.
The sound will be
played back when
the call is terminated.
! Press and hold
/DISP to cancel
demo mode.
! Turn off the
demo display setting.
The display
Demo mode is
screen
on.
changes at random instead of
displaying the
clock continuously even with
the clock display turned on.
! Press and hold
/DISP to cancel
demo mode.
! Turn off the
demo display setting.
The display
Demo mode is
screen
on.
changes at random even with
the display off
turned on.
! Press and hold
/DISP to cancel
demo mode.
! Turn off the
demo display setting.
A Bluetooth con- Do not operate the
nected cellular
cellular phone at
phone is curthis time.
rently being operated.
A call was made
with a Bluetooth
connected cellular phone and
then immediately
terminated. As a
result, communication between
this unit and the
cellular phone
was not terminated properly.
NO XXXX ap- There is no emSwitch the display
pears when a
bedded text infor- or play another
display is chan- mation.
track/file.
ged (NO TITLE,
for example).
The display
Demo mode is
screen
on.
changes at random.
Action
! Press and hold
/DISP to cancel
demo mode.
! Turn off the
demo display setting.
Additional information
Symptom
Cause
The display in- Demo mode is
dication does
on.
not turn off
when EQ/DISP
OFF is pressed
and held down.
Reconnect the
Bluetooth connection between this
unit and the cellular phone.
Text information cannot be
scrolled.
Display scrolling Wait until it warms
is stopped auto- back up.
matically when
the temperature
around this unit
is 50°F or less.
Movie playback
is stopped and
the simple display appears.
Movie playback
is stopped automatically when
the temperature
around this unit
is 50°F or less.
Wait until it warms
back up.
En
41
Appendix
Additional information
Symptom
Cause
Action
Sound from the The audio output Use the iPod to
iPod cannot be direction may
change the audio
heard.
switch automati- output direction.
cally when the
Bluetooth and
USB connections
are used at the
same time.
External storage device (USB, SD)/iPod
Message
Cause
Action
NO DEVICE
No USB storage
device or iPod is
connected.
Connect a compatible USB storage
device/iPod.
FORMAT
READ
Sometimes there
is a delay between the start of
playback and
when you start to
hear any sound.
Wait until the message disappears
and you hear
sound.
NO AUDIO
There are no
songs.
Transfer the audio
files to the USB
storage device and
connect.
The connected
USB storage device has security
enabled.
Follow the USB
storage device instructions to disable the security.
SKIPPED
The connected
USB storage device contains
files embedded
with Windows
Mediaä DRM 9/
10.
Play an audio file
not embedded with
Windows Media
DRM 9/10.
PROTECT
All the files in the
USB storage device are embedded with
Windows Media
DRM 9/10.
Transfer audio files
not embedded with
Windows Media
DRM 9/10 to the
USB storage device and connect.
NOT COMPATIBLE
The USB device
connected to is
not supported by
this unit.
! Connect a USB
Mass Storage
Class compliant
device.
! Disconnect your
device and replace
it with a compatible USB storage
device.
Non-compatible
iPod
Disconnect your
device and replace
it with a compatible iPod.
Non-compatible
SD storage device
Remove your device and replace it
with a compatible
SD storage device.
Error messages
When you contact your dealer or your nearest
Pioneer Service Center, be sure to note the
error message.
CD player
Message
Cause
ERROR-07, 11, The disc is dirty.
12, 17, 30
The disc is
scratched.
Action
Clean the disc.
Replace the disc.
ERROR-10, 11, There is an elec- Turn the ignition
12, 15, 17, 30, trical or mechan- switch OFF and
A0
ical error.
back ON, or switch
to a different
source, then back
to the CD player.
42
ERROR-15
The inserted disc Replace the disc.
is blank.
ERROR-23
Unsupported CD Replace the disc.
format.
FORMAT
READ
Sometimes there
is a delay between the start of
playback and
when you start to
hear any sound.
NO AUDIO
The inserted disc Replace the disc.
does not contain
any playable
files.
SKIPPED
The inserted disc Replace the disc.
contains DRM
protected files.
PROTECT
All the files on
Replace the disc.
the inserted disc
are embedded
with DRM.
En
Wait until the message disappears
and you hear
sound.
Appendix
Additional information
Cause
Action
Message
Cause
Action
The USB connector or USB cable
has shortcircuited.
Check that the
USB connector or
USB cable is not
caught in something or damaged.
ERROR-23
USB storage device was not formatted with
FAT12, FAT16 or
FAT32.
USB storage device should be formatted with FAT12,
FAT16 or FAT32.
The connected
USB storage device consumes
more than maximum allowable
current.
Disconnect the
USB storage device and do not
use it. Turn the
ignition switch to
OFF, then to ACC
or ON and then
connect only compliant USB storage
devices.
ERROR-16
The iPod firmware version is
old.
Update the iPod
version.
iPod failure.
Disconnect the
cable from the
iPod. Once the
iPod’s main menu
is displayed, reconnect the iPod and
reset it.
The iPod operMake sure the conates correctly but nection cable for
does not charge. the iPod has not
shorted out (e.g.,
not caught in
metal objects).
After checking,
turn the ignition
switch OFF and
back ON, or disconnect the iPod
and reconnect.
ERROR-19
Communication
failed.
iPod failure.
! Perform one of
the following operations.
–Turn the ignition
switch OFF and
back ON.
–Disconnect or
eject the external
storage device.
–Change to a different source.
Then, return to the
USB or SD source.
! Disconnect the
cable from the
iPod. Once the
iPod’s main menu
is displayed, reconnect the iPod and
reset it.
Disconnect the
cable from the
iPod. Once the
iPod’s main menu
is displayed, reconnect the iPod and
reset it.
STOP
There are no
Select a list that
songs in the cur- contains songs.
rent list.
Not found
No related
songs.
Additional information
Message
CHECK USB
Transfer songs to
the iPod.
Bluetooth device
Message
Cause
Action
ERROR-10
The power failed
for the Bluetooth
module of this
unit.
Turn the ignition
switch OFF and
then to ACC or ON.
If the error message is still displayed after
performing the
above action,
please contact
your dealer or an
authorized Pioneer
Service Station.
Pandora
Message
Cause
Action
ERROR-19
Communication
failed.
Disconnect the
cable from the
iPod. Once the
iPod’s main menu
is displayed, reconnect the iPod and
reset it.
Start up the
Pandora Application
The Pandora application has not
started running
yet.
Start up the
Pandora application from your
iPod/iPhone.
En
43
Appendix
Additional information
Action
Message
Cause
Action
Try again later Unable to save
thumb rating.
Unable to save
BookMark.
Pandora system
is undergoing
maintenance.
Message
Try again later.
ERR:Outside
Noise
The surrounding
noise level is too
high.
Skip limit
reached
Skip limit
reached.
Do not exceed the
skip limit.
! Stop your car in
a place that is
quiet, and switch
off the engine, air
conditioner and
heater.
! Set the microphone correctly.
Check Application
This version of
the Pandora application is not
supported.
Connect an iPod/
iPhone that has a
compatible version
of the Pandora application installed.
Check Device
No Available
Station
Cause
Device error mes- Please check your
sage displayed in iPod/iPhone.
Pandora Application.
Unable to play
music from
Pandora.
Discs and player
Use only discs that feature either of the following two
logos.
No station found. Create a station in
the Pandora application on your
iPod/iPhone.
No Active Sta- No station setions
lected.
Select a station.
Use 12-cm discs. Do not use 8-cm discs or an adapter
for 8-cm discs.
Auto TA and EQ
Message
Handling guidelines
Cause
Action
Use only conventional, fully circular discs. Do not use
shaped discs.
ERR:MIC check The microphone Plug the supplied
is not connected. microphone securely into the
jack.
ERR:Front
Speaker, ERR:
Front-Lch,
ERR:Front-Rch,
ERR:Rear-Lch,
ERR:Rear-Rch,
ERR:SubWLch, ERR:
SubW-Rch,
ERR:SubWoofer
44
En
The microphone
cannot pick up
the measuring
tone of a speaker.
! Confirm that the
speakers are connected correctly.
! Cancel muting
the front speaker
units.
! Correct the input
level setting of the
power amp connected to the
speakers.
! Set the microphone correctly.
Do not insert anything other than a CD into the CD
loading slot.
Do not use cracked, chipped, warped, or otherwise
damaged discs as they may damage the player.
Unfinalized CD-R/RW discs cannot be played back.
Do not touch the recorded surface of the discs.
Store discs in their cases when not in use.
Do not attach labels, write on or apply chemicals to
the surface of the discs.
To clean a CD, wipe the disc with a soft cloth outward
from the center.
Appendix
Additional information
Condensation may temporarily impair the player’s
performance. Let it rest for about one hour to adjust
to a warmer temperature. Also, wipe any damp discs
off with a soft cloth.
Road shocks may interrupt disc playback.
When using discs that can be printed on label surfaces, check the instructions and the warnings of the
discs. Depending on the discs, inserting and ejecting
may not be possible. Using such discs may result in
damage to this equipment.
Do not attach commercially available labels or other
materials to the discs.
! The discs may warp making the disc unplayable.
! The labels may come off during playback and prevent ejection of the discs, which may result in damage to the equipment.
External storage device (USB, SD)
Address any questions you have about your external
storage device (USB, SD) to the manufacturer of the
device.
Do not leave the external storage device (USB, SD) in
places with high temperatures.
Depending on the external storage device (USB, SD),
the following problems may occur.
! Operations may vary.
! The storage device may not be recognized.
! Files may not be played back properly.
USB storage device
Connections via USB hub are not supported.
Do not connect anything other than a USB storage
device.
Firmly secure the USB storage device when driving.
Do not let the USB storage device fall onto the floor,
where it may become jammed under the brake or accelerator pedal.
Depending on the USB storage device, the following
problems may occur.
! The device may generate noise in the radio.
This unit supports only the following types of SD
memory cards.
! SD
! miniSD
! microSD
! SDHC
Keep the SD memory card out of the reach of children. Should the SD memory card be swallowed, consult a doctor immediately.
Do not touch the connectors of the SD memory card
directly with your fingers or with any metal device.
Do not insert anything other than an SD memory card
into the SD card slot. If a metal object (such as a
coin) is inserted into the slot, the internal circuits may
break and cause malfunctions.
Additional information
Playback of discs may not be possible because of
disc characteristics, disc format, recorded application, playback environment, storage conditions, and
so on.
SD memory card
When inserting a miniSD or microSD, use an adapter.
Do not use an adapter which has metal parts other
than the connectors exposed.
Do not insert a damaged SD memory card (e.g.
warped, label peeled off) as it may not be ejected
from the slot.
Do not try to force an SD memory card into the SD
card slot as the card or this unit may be damaged.
When ejecting an SD memory card, press it and hold
it until it clicks. It is dangerous for you to release your
finger immediately after you press on the card as the
card may shoot out of the slot and hit you in the face,
etc. If the card shoots out of the slot, it may become
lost.
iPod
To ensure proper operation, connect the dock connector cable from the iPod directly to this unit.
Firmly secure the iPod when driving. Do not let the
iPod fall onto the floor, where it may become jammed
under the brake or accelerator pedal.
About iPod settings
! When an iPod is connected, this unit changes the
EQ (equalizer) setting of the iPod to off in order to
optimize the acoustics. When you disconnect the
iPod, the EQ returns to the original setting.
! You cannot set Repeat to off on the iPod when
using this unit. Repeat is automatically changed
to All when the iPod is connected to this unit.
Incompatible text saved on the iPod will not be displayed by the unit.
En
45
Appendix
Additional information
DualDiscs
DualDiscs are two-sided discs that have a recordable
CD for audio on one side and a recordable DVD for
video on the other.
Since the CD side of DualDiscs is not physically compatible with the general CD standard, it may not be
possible to play the CD side with this unit.
Frequent loading and ejecting of a DualDisc may result in scratches on the disc. Serious scratches can
lead to playback problems on this unit. In some
cases, a DualDisc may become stuck in the disc loading slot and will not eject. To prevent this, we recommend you refrain from using DualDisc with this unit.
Please refer to the information from the disc manufacturer for more detailed information about
DualDiscs.
WAV
File extension: .wav
Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM)
Sampling frequency: 16 kHz to 48 kHz (LPCM),
22.05 kHz and 44.1 kHz (MS ADPCM)
AAC
Compatible format: AAC encoded by iTunes
File extension: .m4a
Sampling frequency: 11.025 kHz to 48 kHz
Transmission rate: 16 kbps to 320 kbps, VBR
Apple Lossless: Not compatible
CAUTION
Do not leave the discs/external storage device
(USB, SD) or iPod in places with high
temperatures.
Compressed audio
compatibility (disc, USB, SD)
WMA
File extension: .wma
Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to
384 kbps (VBR)
Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
Windows Media Audio Professional, Lossless, Voice/
DRM Stream/Stream with video: Not compatible
MP3
AAC file bought from the iTunes Store (.m4p file extension): Not compatible
Supplemental information
Only the first 32 characters can be displayed as a file
name (including the file extension) or a folder name.
This unit may not operate correctly depending on the
application used to encode WMA files.
There may be a slight delay at the start of playback of
audio files embedded with image data or audio files
stored on a USB storage device that has numerous
folder hierarchies.
Russian text to be displayed on this unit should be encoded in one of the following character sets:
! Unicode (UTF-8, UTF-16)
! A character set other than Unicode that is used in
a Windows environment and is set to Russian in
the multi-language setting
Disc
File extension: .mp3
Bit rate: 8 kbps to 320 kbps (CBR), VBR
Playable folder hierarchy: up to eight tiers (A practical
hierarchy is less than two tiers).
Sampling frequency: 8 kHz to 48 kHz (32 kHz, 44.1 kHz,
48 kHz for emphasis)
Playable folders: up to 99
Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3
tag Version 2.x is given priority over Version 1.x.)
M3u playlist: Not compatible
MP3i (MP3 interactive), mp3 PRO: Not compatible
46
En
Playable files: up to 999
File system: ISO 9660 Level 1 and 2, Romeo, Joliet
Multi-session playback: Compatible
Appendix
Additional information
Packet write data transfer: Not compatible
Regardless of the length of blank sections between
the songs from the original recording, compressed
audio discs play with a short pause between songs.
Playable folder hierarchy: up to eight tiers (A practical
hierarchy is less than two tiers).
Playable folders: up to 1 500
Playable files: up to 15 000
Playback of copyright-protected files: Not compatible
Partitioned external storage device (USB, SD): Only
the first playable partition can be played.
There may be a slight delay when starting playback of
audio files on a USB storage device with numerous
folder hierarchies.
SD memory card
This unit supports only the following iPod models.
Supported iPod software versions are shown below.
Older versions may not be supported.
Made for
! iPod touch 4th generation (software version 4.1)
! iPod touch 3rd generation (software version 3.1.1)
! iPod touch 2nd generation (software version 2.1.1)
! iPod touch 1st generation (software version 1.1)
! iPod classic 160GB (software version 2.0.2)
! iPod classic 120GB (software version 2.0)
! iPod classic (software version 1.0)
! iPod with video (software version 1.2.3)
! iPod nano 6th generation (software version 1.0)
! iPod nano 5th generation (software version 1.0.1)
! iPod nano 4th generation (software version 1.0)
! iPod nano 3rd generation (software version 1.0)
! iPod nano 2nd generation (software version 1.1.3)
! iPod nano 1st generation (software version 1.3.1)
! iPhone 4 (software version 4.1)
! iPhone 3GS (software version 3.0)
! iPhone 3G (software version 2.0)
! iPhone (software version 1.1.1)
There is no compatibility for Multi Media Cards
(MMC).
Depending on the generation or version of the iPod,
some functions may not be available.
Compatibility with all SD memory cards is not guaranteed.
Operations may vary depending on the software version of iPod.
This unit is not compatible with SD-Audio.
When using an iPod, an iPod Dock Connector to USB
Cable is required.
CAUTION
! Pioneer accepts no responsibility for data lost
on USB memory/USB portable audio players/
SD memory cards/SDHC memory cards, even
if that data is lost while this unit is used.
! Pioneer cannot guarantee compatibility with
all USB mass storage devices and assumes
no responsibility for any loss of data on media
players, smart phones, or other devices while
using this product.
Additional information
External storage device (USB, SD)
iPod compatibility
A Pioneer CD-IU51 interface cable is also available.
For details, consult your dealer.
About the file/format compatibility, refer to the iPod
manuals.
Audiobook, Podcast: Compatible
CAUTION
Pioneer accepts no responsibility for data lost on
the iPod, even if that data is lost while this unit is
used.
Sequence of audio files
The user cannot assign folder numbers and
specify playback sequences with this unit.
En
47
Appendix
Additional information
Example of a hierarchy
01
02
03
04
05
Level 1 Level 2 Level 3 Level 4
: Folder
: Compressed
audio file
01 to 05: Folder
number
1 to 6: Playback
sequence
Disc
Folder selection sequence or other operation
may differ depending on the encoding or writing software.
External storage device (USB, SD)
The playback sequence is the same as the recorded sequence in the external storage device (USB, SD).
To specify the playback sequence, the following method is recommended.
1 Create a file name that includes numbers that
specify the playback sequence (e.g.,
001xxx.mp3 and 099yyy.mp3).
2 Put those files into a folder.
3 Save the folder that contains the files to the
external storage device (USB, SD).
However, depending on the system environment, you may not be able to specify the playback sequence.
For USB portable audio players, the sequence
is different and depends on the player.
Bluetooth profiles
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles. This unit is compatible with the following
profiles.
! GAP (Generic Access Profile)
! SDP (Service Discovery Protocol)
! OPP (Object Push Profile)
! HFP (Hands Free Profile)
! HSP (Head Set Profile)
48
En
! PBAP (Phone Book Access Profile)
! A2DP (Advanced Audio Distribution Profile)
! AVP (Audio/Video Profile)
! AVRCP (Audio/Video Remote Control Profile) 1.0
Copyright and trademark
Bluetooth
The Bluetoothâ word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by PIONEER CORPORATION is under license. Other trademarks
and trade names are those of their respective
owners.
iTunes
Apple and iTunes are trademarks of Apple
Inc., registered in the U.S. and other countries.
MP3
Supply of this product only conveys a license
for private, non-commercial use and does not
convey a license nor imply any right to use
this product in any commercial (i.e. revenuegenerating) real time broadcasting (terrestrial,
satellite, cable and/or any other media), broadcasting/streaming via internet, intranets and/
or other networks or in other electronic content distribution systems, such as pay-audio or
audio-on-demand applications. An independent license for such use is required. For details, please visit
http://www.mp3licensing.com.
WMA
Windows Media is either a registered trademark or trademark of Microsoft Corporation in
the United States and/or other countries.
This product includes technology owned by
Microsoft Corporation and cannot be used or
distributed without a license from Microsoft
Licensing, Inc.
Appendix
Additional information
Additional information
SD memory card
SD Logo is a trademark of SD-3C, LLC.
miniSD Logo is a trademark of SD-3C, LLC.
microSD Logo is a trademark of SD-3C, LLC.
SDHC Logo is a trademark of SD-3C, LLC.
iPod & iPhone
iPhone, iPod, iPod classic, iPod nano, and
iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean
that an electronic accessory has been designed to connect specifically to iPod or
iPhone, respectively, and has been certified by
the developer to meet Apple performance
standards. Apple is not responsible for the operation of this device or its compliance with
safety and regulatory standards. Please note
that the use of this accessory with iPod or
iPhone may affect wireless performance.
Pandora
Pandora is a registered trademark of Pandora
Media, Inc.
En
49
Appendix
Additional information
Specifications
General
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system ................... Negative type
Maximum current consumption
..................................................... 10.0 A
Dimensions (W × H × D):
DIN
Chassis ..................... 178 mm × 50 mm ×
165 mm
(7 in. × 2 in. × 6-1/2 in.)
Nose ........................... 188 mm × 58 mm × 17 mm
(7-3/8 in.× 2-1/4 in.× 5/8 in.)
Chassis ..................... 178 mm × 50 mm ×
165 mm
(7 in.× 2 in.× 6-1/2 in.)
Nose ........................... 170 mm × 46 mm × 17 mm
(6-3/4 in.× 1-3/4 in.× 5/8 in.)
Weight .......................................... 1.2 kg (2.6 lbs)
Audio
Maximum power output ....... 50 W × 4
Continuous power output ... 22 W × 4 (50 Hz to
15 000 Hz, 5 % THD,
4 W load, both channels driven)
Load impedance ...................... 4 W to 8 W × 4
Preout maximum output level
..................................................... 5.0 V
Loudness contour ................... +10 dB (100 Hz), +6.5 dB
(10 kHz) (volume: –30 dB)
Equalizer (Left/Right independent 16-Band Graphic
Equalizer):
Frequency .......................... 20 Hz/31.5 Hz/50 Hz/80 Hz/
125 Hz/200 Hz/315 Hz/
500 Hz/800 Hz/1.25 kHz/
2 kHz/3.15 kHz/5 kHz/8 kHz/
12.5 kHz/20 kHz
Equalization range ........ ±12 dB (2 dB step)
Auto equalizer:
(Front & rear & subwoofer/High & mid & low)
Frequency .......................... 20 Hz/31.5 Hz/50 Hz/80 Hz/
125 Hz/200 Hz/315 Hz/
500 Hz/800 Hz/1.25 kHz/
2 kHz/3.15 kHz/5 kHz/8 kHz/
12.5 kHz/20 kHz
Equalization range ........ +6 dB to –12 dB (2 dB step)
Network (standard mode):
HPF (front)
Frequency ................ 50 Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
50
En
Slope .......................... 0 (Pass)/–6 dB/oct./–12 dB/
oct.
Gain ............................ 0 dB to –24 dB/Mute (1 dB
step)
HPF (rear)
Frequency ................ 50 Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Slope .......................... 0 (Pass)/–6 dB/oct./–12 dB/
oct.
Gain ............................ +6 dB to –24 dB/Mute (1
dB step)
Subwoofer (stereo/mono):
Frequency ................ 50 Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Slope .......................... –6 dB/oct./–12 dB/oct./–
18 dB/oct.
Gain ............................ +6 dB to –24 dB/Mute (1
dB step)
Phase ........................ Normal/Reverse
Network (3-way network mode):
High HPF:
Frequency ................ 1.25 kHz/1.6 kHz/2 kHz/
2.5 kHz/3.15 kHz/4 kHz/
5 kHz/6.3 kHz/8 kHz/10 kHz/
12.5 kHz
Slope .......................... –6 dB/oct./–12 dB/oct./–
18 dB/oct./–24 dB/oct.
Gain ............................ 0 dB to –24 dB/Mute (1 dB
step)
Phase ........................ Normal/Reverse
Mid HPF/LPF:
Frequency (LPF) ... 1.25 kHz/1.6 kHz/2 kHz/
2.5 kHz/3.15 kHz/4 kHz/
5 kHz/6.3 kHz/8 kHz/10 kHz/
12.5 kHz
Frequency (HPF)
................................. 25 Hz/31.5 Hz/40 Hz/50 Hz/
63 Hz/80 Hz/100 Hz/125 Hz/
160 Hz/200 Hz/250 Hz
Slope (LPF) ............. 0 (Pass)/–6 dB/oct./–12 dB/
oct./–18 dB/oct./–24 dB/oct.
Slope (HPF) ............ 0 (Pass)/–6 dB/oct./–12 dB/
oct./–18 dB/oct./–24 dB/oct.
Gain ............................ 0 dB to –24 dB/Mute (1 dB
step)
Phase ........................ Normal/Reverse
Low LPF (stereo/mono):
Frequency ................ 25 Hz/31.5 Hz/40 Hz/50 Hz/
63 Hz/80 Hz/100 Hz/125 Hz/
160 Hz/200 Hz/250 Hz
Slope .......................... –12 dB/oct./–18 dB/oct./–
24 dB/oct./–30 dB/oct./–
36 dB/oct.
Appendix
Additional information
Gain ............................ +6 dB to –24 dB/Mute (1
dB step)
Phase ........................ Normal/Reverse
Usable sensitivity ..................... 9 dBf (0.8 µV/75 W, mono,
S/N: 30 dB)
Signal-to-noise ratio ............... 72 dB (IHF-A network)
AM tuner
System .......................................... Compact disc audio system
Usable discs .............................. Compact disc
Signal-to-noise ratio ............... 105 dB (1 kHz) (IHF-A network)
Number of channels .............. 2 (stereo)
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12
(2 ch audio)
(Windows Media Player)
AAC decoding format ............ MPEG-4 AAC (iTunes encoded only) (.m4a)
(Ver. 9.2 and earlier)
WAV signal format .................. Linear PCM & MS ADPCM
(Non-compressed)
Frequency range ...................... 530 kHz to 1 710 kHz
Usable sensitivity ..................... 25 µV (S/N: 20 dB)
Signal-to-noise ratio ............... 62 dB (IHF-A network)
Additional information
CD player
Bluetooth
Version .......................................... Bluetooth 3.0 certified
Output power ............................ +4 dBm Maximum
(Power class 2)
CEA2006 Specifications
USB
USB standard specification
..................................................... USB 2.0 full speed
Maximum current supply .... 1 A
USB Class ................................... MSC (Mass Storage Class)
File system .................................. FAT12, FAT16, FAT32
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12
(2 ch audio)
(Windows Media Player)
AAC decoding format ............ MPEG-4 AAC (iTunes encoded only) (.m4a)
(Ver. 9.2 and earlier)
WAV signal format .................. Linear PCM & MS ADPCM
(Non-compressed)
Power output ............................. 14 W RMS × 4 Channels
(4 W and ≦ 1 % THD+N)
S/N ratio ....................................... 91 dBA (reference: 1 W into
4 W)
Note
Specifications and the design are subject to modifications without notice.
SD
Compatible physical format
..................................................... Version 2.00
Maximum memory capacity
..................................................... 32 GB (for SD and SDHC)
File system .................................. FAT12, FAT16, FAT32
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12
(2 ch audio)
(Windows Media Player)
AAC decoding format ............ MPEG-4 AAC (iTunes encoded only) (.m4a)
(Ver. 9.2 and earlier)
WAV signal format .................. Linear PCM & MS ADPCM
(Non-compressed)
FM tuner
Frequency range ...................... 87.9 MHz to 107.9 MHz
En
51
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi,
Kanagawa 212-0031, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202 Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada
TEL: 1-877-283-5901
TEL: 905-479-4411
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Avila Camacho 138 10 piso
Col.Lomas de Chapultepec, Mexico, D.F. 11000
TEL: 55-9178-4270
先鋒股份有限公司
台北市內湖區瑞光路407號8樓
電話 : 886-(0)2-2657-3588
先鋒電子（香港）有限公司
香港九龍長沙灣道909號5樓
電話 : 852-2848-6488
ã 2011 PIONEER CORPORATION.
All rights reserved.
 <11L00000>
 UC

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Signing Date                    : 2011:11:22 14:14:57+09:00
Signing Authority               : ARE Acrobat Product v8.0 P23 0002337
Annotation Usage Rights         : Create, Delete, Modify, Copy, Import, Export
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 5.0 (Windows)
Create Date                     : 2011:11:22 02:01:34Z
Modify Date                     : 2011:11:22 14:14:57+09:00
Metadata Date                   : 2011:11:22 14:14:57+09:00
Creator Tool                    : Arbortext Advanced Print Publisher 9.1.520/W Unicode
Format                          : application/pdf
Document ID                     : uuid:9895833a-b8a4-4900-a7e7-0aa111edd449
Instance ID                     : uuid:6cd112c3-e316-4d51-9001-62ff231511bb
Has XFA                         : No
Page Count                      : 52
Creator                         : Arbortext Advanced Print Publisher 9.1.520/W Unicode

EXIF Metadata provided by EXIF.tools