Pioneer Pro 1140Hd Users Manual ARB1573 A

If not then 366322056PRO940HDOperatingInstructions Manual: ://www.pioneerelectronics.com/pio/pe/images/portal/cit_11221/366322056PRO940HDOperatingInstructions

If not then 366322046PRO1540HDOperatingInstructions Manual: ://www.pioneerelectronics.com/pio/pe/images/portal/cit_11221/366322046PRO1540HDOperatingInstructions

PRO-940HD to the manual e20c3aff-9fe0-4183-8742-cc4cfb47540b

2015-01-26

: Pioneer Pioneer-Pro-1140Hd-Users-Manual-334372 pioneer-pro-1140hd-users-manual-334372 pioneer pdf

Open the PDF directly: View PDF .
Page Count: 120

Download
Open PDF In Browser	View PDF

PDP_PRO1540HD.book Page 1 Wednesday, August 2, 2006 6:01 PM

PLASMA DISPLAY SYSTEM

PRO-1540HD
PRO-1140HD
PRO-940HD

www.pioneerelectronics.com (US)
www.pioneerelectronics.ca (Canada)

Operating Instructions

PDP_PRO1540HD.book Page 2 Wednesday, August 2, 2006 6:01 PM

1)
2)
3)
4)
5)
6)
7)

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.

NOTE TO CATV SYSTEM INSTALLER
THIS REMINDER IS PROVIDED TO CALL THE CATV
SYSTEM INSTALLER’S ATTENTION TO ARTICLE
820-40 OF THE NEC THAT PROVIDES GUIDELINES
FOR PROPER GROUNDING AND, IN PARTICULAR,
SPECIFIES THAT THE CABLE GROUND SHALL BE
CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF
D1-4-2-8_En
CABLE ENTRY AS PRACTICAL.

11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.

13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

This digital television is capable of receiving analog
basic, digital basic and digital premium cable
television programming by direct connection to a cable
system providing such programming. A security card
provided by your cable operator is required to view
encrypted digital programming. Certain advanced and
interactive digital cable services such as video-ondemand, a cable operator’s enhanced program guide
and data-enhanced television services may require the
use of a set-top box. For more information call your
local cable operator.

WARNING: This product equipped with a threewire grounding (earthed) plug - a plug that has a third
(grounding) pin. This plug only fits a grounding-type
power outlet. If you are unable to insert the plug into an
outlet, contact a licensed electrician to replace the
outlet with a properly grounded one. Do not defeat the
safety purpose of the grounding plug
D3-4-2-1-6_A_En

VENTILATION CAUTION:

WARNING: To prevent a fire hazard, do not place

WARNING: Slots and openings in the cabinet are

any naked flame sources (such as a lighted candle) on
the equipment.
D3-4-2-1-7a_A_En

When installing this unit, make sure to leave space
around the unit for ventilation to improve heat
radiation. For the minimum space required, see page
20.

provided for ventilation to ensure reliable operation of
the product, and to protect it from overheating. To
prevent fire hazard, the openings should never be
blocked or covered with items (such as newspapers,
table-cloths, curtains) or by operating the equipment
on thick carpet or a bed.

PDP_PRO1540HD.book Page 3 Wednesday, August 2, 2006 6:01 PM

WARNING:

WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to lead, a chemical known to
the State of California and other governmental entities
to cause cancer and birth defects or other reproductive
harm. Wash hands after handling.
Information to User
Alteration or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
[For Canadian model]
This Class B digital apparatus complies with Canadian
ICES-003.

FEDERAL COMMUNICATIONS
COMMISSION DECLARATION OF
CONFORMITY
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Product Name: Plasma Display System
Model Number: PRO-1540HD/PRO-1140HD/PRO-940HD
Product Category: Class B Personal Computers &
Peripherals
Responsible Party Name: PIONEER ELECTRONICS
SERVICE, INC.
Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA
90801-1760, U.S.A.
Phone: 800-421-1625
For Business Customer URL
http://www.PioneerUSA.com

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
–
–
–
–

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_En

CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the
unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and
televisions, use shielded cables and connectors for connections.
D8-10-3a_En
IMPORTANT NOTICE – THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR.
PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND
KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.
D1-4-2-6-1_En
CAUTION: The power switch does not completely separate the unit from the mains in off position. Therefore
install the unit suitable places easy to disconnect the mains plug in case of the accident. The mains plug of unit
should be unplugged from the wall socket when left unused for a long period of time.
STANDBY:

When placed into the standby mode, the main power flow is cut and the unit is no longer
fully operational.
STANDBY/ON Indicator: The indicator is lit red when the unit is in the standby mode and lit blue when it is in the
power-on mode. No operation can be performed when the indicator is off. However, the
Plasma Display System will still consume some power as long as the power cord is
inserted into the power outlet.

CAUTION:
Operating Environment
Operating environment temperature and humidity:
+0 ˚C to +40 ˚C (+32 ˚F to +104 ˚F), less than 85 %RH (cooling vents not blocked) Do not install this unit in a
poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

English

THE
APPARATUS
IS
NOT
WATERPROOFS, TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE AND DO NOT PUT ANY WATER
SOURCE NEAR THIS APPARATUS, SUCH AS VASE,
FLOWER POT, COSMETICS CONTAINER AND
MEDICINE BOTTLE ETC.

PDP_PRO1540HD.book Page 4 Wednesday, August 2, 2006 6:01 PM

Contents
Contents

Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly. After you have finished
reading the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the
explanatory drawings. However the method of connecting and operating the unit is the same.
Illustrations shown in this manual are for the PRO-1140HD unless otherwise specified.

01 Important User Guidance Information
02 Safety Precautions
03 Supplied Accessories
04 Part Names

Plasma Display ...........................................13
Remote control unit ...................................19
05 Preparation

Installing the Plasma Display ...................20
Moving the Plasma Display .......................20
Preventing the Plasma Display from
Falling Over .................................................21
Attaching/detaching the PIONEER stand
(for PRO-940HD only) ................................22
Cable connections for watching digital
and/or conventional TV channels .............23
Connecting VHF/UHF antennas and a
Cable .......................................................23
Inserting the CableCARD™ .......................23
Switching between antenna A and B .......23
Preparing the remote control unit ............24
Inserting batteries .................................24
Cautions regarding batteries ................24
Allowed operation range of the remote
control unit .............................................24
Cautions regarding the remote control
unit ..........................................................24
Connecting the power cord .......................25
Routing cables ...........................................25
06 Basic Operations

Turning on the power .................................26
Turning off the power .................................26
Watching TV channels ...............................27
Selecting the antenna ...........................27
Changing channels ...............................27
Changing the volume and sound .........28
Changing the language ........................28
Setting MTS/SAP mode ........................29
Viewing a channel banner ....................30
4
En

Using the POD service ......................... 30
Using the multiscreen functions ............. 30
Splitting the screen .............................. 30
Freezing images .................................... 31
07 TV Guide On Screen™ System Setup

About the TV Guide On Screen™
system ........................................................ 32
Setting up the TV Guide On Screen™
system ........................................................ 32
08 Menu Setup

Menu Configuration .................................. 36
AV mode menus ................................... 36
PC mode menus ................................... 36
Menu operations ................................... 36
09 Tuner Setup

Setting up TV channels ............................. 37
Using Auto Channel Preset ................. 37
Setting for skipping unwanted
channels ................................................ 37
Setting up TV channels manually ....... 37
Checking signal strength ..................... 37
Checking the CableCARD ID ............... 38
Parental Control ........................................ 38
Changing the password ....................... 38
Clearing the password ......................... 39
Activating the Parental Control ........... 39
Setting the voluntary movie rating
system (MPAA) ..................................... 39
Setting the TV ratings ........................... 39
Setting the TV Parental Guidelines
(TV Guidelines) ...................................... 40
Blocking Not Rated TV programs ........ 40
Canadian rating systems ..................... 40
Setting Canadian English ratings ....... 41
Setting Canadian French ratings ........ 41
Setting new ratings .............................. 41
Deleting new ratings ............................ 42
Temporarily deactivating the Parental
Control ................................................... 42
Setting your favorite channels ................. 43

PDP_PRO1540HD.book Page 5 Wednesday, August 2, 2006 6:01 PM

Contents

10 TV Guide On Screen™ System Operation

Using the TV Guide On Screen™
system ........................................................ 46
Screen components .................................. 46
TV Guide On Screen™ icons ................ 46
TV Guide On Screen™ navigation ....... 47
The Listings screen ................................... 47
Recording programs ................................. 48
Setting program reminders ...................... 49
Searching for programs ........................... 51
Searching by category .......................... 51
Searching by keyword .......................... 52
Alphabetical search ............................. 53
The search Episode Options menu ..... 53
Scheduling recordings and reminders ... 54
The Schedule Options menu ............... 54
Changing setup options ........................... 55
Changing the System Settings ............ 55
Changing the Channel Display
settings .................................................. 55
Changing the Default Options ............. 56
11 Adjustments and Settings

Sleep Timer ................................................ 57
AV Selection .............................................. 57
Basic picture adjustments ....................... 58
Advanced picture adjustments ................ 59
Using PureCinema ............................... 59
Using Color Temp ................................. 59
Using CTI ............................................... 60
Using Color Management .................... 60
Using Color Space ................................ 60
Using Intelligent Color ......................... 60
Eliminating noise from images ........... 61
Using the Dynamic Range Expander
(DRE) functions .................................... 61
Using the 3DYC and I-P Mode ............. 62
Sound adjustments ................................... 62
FOCUS ................................................... 63
Front Surround ..................................... 63

Power Control ............................................ 63
Energy Save ........................................... 63
No Signal off (AV mode only) ............... 63
No Operation off (AV mode only) ......... 64
Power Management
(PC mode only) ...................................... 64
Image position adjustment
(AV mode only) .......................................... 64
Automatic image position and clock
(Hertz) adjustments (PC mode only) ....... 64
Manual image position and clock
adjustments (PC mode only) .................... 65
Selecting a screen size manually ............. 65
Selecting a screen size automatically ..... 66
Selecting a screen size for 4:3 aspect
ratio signals ........................................... 66
Changing the brightness on both sides of
the screen (Side Mask) ............................. 67
Language setting ....................................... 67

English

Setting up closed captions ....................... 43
Activating the closed caption .............. 43
Selecting the type of conventional
closed captions ..................................... 43
Selecting digital closed captions ........ 44
Selecting digital closed caption
parameters ............................................ 44
Clock Setting ............................................. 44

12 Using External Equipment

About External Equipment ....................... 68
Watching a DVD image ............................ 68
Connecting a DVD player ..................... 68
Displaying a DVD image ...................... 68
Watching a VCR image ............................. 68
Connecting a VCR ................................. 68
Displaying a VCR image ....................... 68
Using HDMI Input ..................................... 69
Connecting HDMI equipment ............. 69
Using a game console or watching
camcorder images .................................... 70
Connecting a game console or
camcorder ............................................. 70
Displaying an image of the game
console or camcorder .......................... 70
Recording digital TV programs using
a VCR .......................................................... 70
Avoiding unwanted feedback .............. 70
Connecting a recorder ......................... 71
Connecting other audio equipment ......... 71
Connecting an AV receiver .................. 71
Watching an image from a computer ..... 72
Connecting a personal computer ........ 72
Displaying an image from a PC ........... 72
Computer compatibility chart .................. 73
G-LINK™ connection ................................. 73
Connecting control cables ....................... 74
About SR+ ............................................ 74
5
En

PDP_PRO1540HD.book Page 6 Wednesday, August 2, 2006 6:01 PM

Contents
Enjoying the Home Media Gallery ............75
Making network connections ...............76
Connecting a USB device .....................76
Starting the Home Media Gallery
function ..................................................77
Enjoying movie files ..............................79
Enjoying music files ..............................82
Enjoying photo files ...............................83
Other useful functions ..........................86
Glossary ..................................................91
13 Useful Remote Control Features

Learning function of the remote
control unit .................................................92
Using the learning function .................92
Presetting manufacturer codes to
control other devices .................................92
Presetting manufacturer codes ...........92
Library Search ........................................92
Delete Learning .....................................92
Manufacturing Reset ............................93
Programming codes ............................94
CABLE ....................................................94
SATELLITE ..............................................94
VCR .........................................................95
PVR .........................................................97
DVD .........................................................97
DVD-R .....................................................98
LD ............................................................98
Using the remote control unit to control
other devices ..............................................99
Receiver control buttons .......................99
CBL/SAT control buttons ....................100
VCR control buttons ............................101
DVD/DVR control buttons ...................102
14 Appendix

Troubleshooting .......................................103
Specifications ...........................................117

6
En

PDP_PRO1540HD.book Page 7 Wednesday, August 2, 2006 6:01 PM

Important User Guidance Information
Important User Guidance Information

Usage guidelines
All phosphor-based screens (including conventional tube-type
televisions) can be affected by static images appearing for a
prolonged period. Plasma displays are no exception to this
rule. After-image and permanent effects on the screen can be
avoided by taking some basic precautions.
• Whenever possible, avoid showing the same image or lowmotion pictures (e.g. closed-captioned images or video
game images which have static portions).
• Avoid viewing the On Screen Display (OSD) for extended
periods (from a DVD player, VCR, and all other components).
• Do not leave the same picture, freeze-framed or paused
continuously, shown over a long period of time when using
the still picture mode from a TV, VCR, DVD player or any
other component.
• Images which have both very bright areas and very dark
areas side by side should not be displayed for a prolonged
period of time.
• When playing a video game, the “GAME” mode setting within
“AV Selection” is strongly recommended. However, please
do not use this mode for long periods of time.
• After playing a game, displaying a PC image, or any still
image, it is best to view a normal moving picture in the
“WIDE” or “FULL” screen setting for over 3 times longer than
the previous still/moving image was shown.
• After using the Plasma Display System, always switch the
display to Standby.
• Extensive viewing of content with top, bottom, or side masks
may cause uneven wear. After viewing masked content, view
full screen motion video for an equal or greater amount of
time.

Installation guidelines
The Pioneer PureVision PRO-1540HD/PRO-1140HD/PRO940HD Plasma Display Panel incorporates a very thin design.
To ensure safety, please take the proper measures when
mounting or installing the Plasma Display. Prevent the unit
from tipping over during vibration or accidental movement.
This product should be installed by using only parts and
accessories designed by PIONEER. Use of installation or
mounting accessories other than PIONEER-approved stands
or brackets may result in instability and could cause injury. For
custom installation, please consult the dealer where the unit
was purchased. To ensure correct installation, experienced
and qualified experts must install the unit. PIONEER is not
responsible for accident or damage caused by the use of parts
and/or accessories manufactured by other unauthorized
companies.
To avoid malfunction and overheating when installing, make
sure that the vents on the main unit are not blocked. To ensure
proper venting:
• Distance the unit slightly from other equipment, walls, etc.
For the minimum space required around the unit, see page
20.
• Do not place the unit inside a narrow place where ventilation
is poor.
• Do not cover with a cloth, etc.
• Clean the vents on the sides and rear of the unit to remove
dust build-up. Use a vacuum cleaner set to its lowest suction
setting to clear dust.
• Do not place the product on a carpet or blanket.
• Do not leave the product tilted at an angle without proper
anchoring.
• Do not invert the product.
Using the unit without proper ventilation may cause the
internal temperature to rise, and could result in possible
malfunction. When the surrounding or internal temperature
exceeds a certain degree, the display automatically powers
OFF in order to cool the internal electronics.
Malfunction can be caused by many factors: inappropriate
installation site, improper assembly/installation/mounting,
improper operation of or modifications made to this product,
etc. PIONEER is not responsible for accidents or malfunction
caused by the above situations.

English

In order to obtain maximum enjoyment from this Pioneer
PureVision PRO-1540HD/PRO-1140HD/PRO-940HD Plasma
Display Panel, please first read this information carefully.
With the Pioneer PureVision PRO-1540HD/PRO-1140HD/PRO940HD, you can be assured of a high quality Plasma Display
Panel with long-life and high reliability. To achieve images of
exceptional quality, this Pioneer Plasma Display Panel
incorporates state-of-the-art design and construction as well
as precise and highly advanced technology.
The Pioneer PureVision PRO-1540HD/PRO-1140HD/PRO940HD incorporates the latest in color filter technology – Direct
Color Filter. This filter technology improves color reproduction
over previous models. It also eliminates the need for a glass
panel to be layered in front of the plasma panel. This feature
which furthers Pioneer’s goal of reducing environmental waste
in consumer electronics, during the manufacturing process
and in the future during the recycling process.
Over the course of its lifetime, the luminosity of the Pioneer
PRO-1540HD/PRO-1140HD/PRO-940HD Plasma Display
System will diminish very slowly, which happens to all
phosphor-based screens (for example, a traditional tube-type
television). To enjoy beautiful and bright images on your
Pioneer Plasma Display Panel for many years to come, please
carefully read and follow the usage guidelines below.

NOTE
The following points are typical effects and characteristics of a
phosphor-based matrix display and as such, are not covered by
the manufacturer’s limited warranties:
• Permanent residual images upon the panel’s phosphors.
• Existence of a small number of inactive light cells.
• Panel generated sounds (Fan motor noise, electrical circuit
humming, glass panel buzzing, etc.)

7
En

PDP_PRO1540HD.book Page 8 Wednesday, August 2, 2006 6:01 PM

Important User Guidance Information
CAUTION
PIONEER bears no responsibility for any damage arising from
incorrect use of the product malfunctions when in use, other
product related problems, and use of the product except in
cases where the company must be liable.

Plasma Display protection function
When still images (such as photos and computer images) stay
on the screen for an extended period of time, the screen
slightly dims. This function automatically adjusts the
brightness to protect the screen when a still image is detected.
The screen is dimmed for approximately three minutes.

Information of pixel defect
Plasma screens display information using pixels. Pioneer
plasma display panels contain a very large number of pixels. (A
42" panel has over 2.3 million pixels, a 50" panel has over 3.1
million pixels and a 60" panel over 3.1 million pixels). All
Pioneer plasma panels are manufactured using a very high
level of ultra-precision technology and undergo individual
quality control.
In rare cases, one or more pixels may remain switched Off or
On. A pixel that remains Off appears as a tiny black dot on the
screen while an active pixel appears as a dot of a particular
color.
This effect is common to all plasma displays because it is a
consequence of the technology.
If the defective pixels are visible at a normal viewing distance of
between 2.5 and 3.5 meters (8.2 and 11.5 feet) while viewing a
normal broadcast (i.e. not a test card, still image, or single color
display) please contact Pioneer Customer Support Div. (USA) or
Customer Satisfaction Dept. (CANADA). See back cover for
contact information.
If, however, the fixed pixel(s) can only be seen from a distance
of less than 8 feet or during single color displays then the
appearance is considered normal for plasma technology.

Infrared rays
The Plasma Display releases infrared rays because of the panel
characteristics. Surrounding equipment with remote controls
and wireless headphones using infrared signals can
experience interference. Move any affected equipment to a
location away from the plasma panel.

Radio interference
While this product meets required specifications, the panel
emits a small amount of electronic noise. This noise can affect
radio, computer, and VCR reception. Move devices away from
the panel to reduce or eliminate interference.

Plasma Display driving sound
The screen of the Plasma Display is composed of extremely
fine pixels and these pixels emit light according to received
video signals. This principle may cause you to hear a buzz or
electrical hum coming from the Plasma Display.

Do not attach such items as labels and tape to the
product.
• Labels and tape can mar or discolor the cabinet.

8
En

When not using the product for a long time
• If you do not use the product for a long time, the functions of
the product may be adversely affected. Switch ON and run
the product occasionally to maintain quality.

Condensation
• Condensation may take place on the surface or inside of the
panel when the unit is rapidly moved from a cold place to a
warm place or when a heater is turned On in the room. When
condensation occurs, do not switch On the panel until
condensation disappears. Operating the panel when there is
condensation can damage the unit.

Cleaning the surface of the screen and the glossy
surface of the front cabinet
• When cleaning the surface of the screen or the glossy
surface of the front cabinet, gently wipe with the supplied
cleaning cloth or a similar cloth (e.g., cotton, flannel, etc.).
Using a dirty or course material cloth can scratch and
damage the panel’s surfaces.
• If you clean the surface of the screen with a wet cloth, water
droplets may enter into the product, resulting in a
malfunction.

Cleaning the cabinet
• When cleaning other panel surfaces, gently wipe with a
clean soft cloth (e.g., cotton, flannel, etc.). Using a dirty or
course material cloth can scratch and damage the panel’s
surfaces.
• The cabinet of this product is mostly composed of plastic. Do
not use chemicals such as benzene or thinner to clean the
cabinet. Using these chemicals can strip the surface coating
or cause cabinet deterioration.
• Do not expose the product to a volatile gas or fluid such as
pesticide. Do not apply rubber or vinyl products to the
cabinet for long periods of time. The effect of plasticizer on
the cabinet can strip the surface coating or cause
deterioration.
• If you clean the surface of the cabinet with a wet cloth, water
droplets may enter into the product, resulting in a
malfunction.

Handles at the rear of the Plasma Display
• Do not remove the handles from the rear of the Plasma
Display.
• When moving the Plasma Display, ask another person for
help and use the handles attached to the rear of the Plasma
Display. Do not move the Plasma Display by holding only a
single handle. Use the handles as shown on page 20.
• Do not use the handles to hang, suspend, or anchor the
panel.

Fan motor noise
The rotation speed of the cooling fan motor increases when the
ambient temperature of the Plasma Display becomes high.
You may hear the sound of the fan motor at that time.

PDP_PRO1540HD.book Page 9 Wednesday, August 2, 2006 6:01 PM

Important User Guidance Information

About the menu window size following video
format switch

If this happens, the menu will return to its normal size after two
to three seconds. This action is normal, and does not indicate
a problem with your Plasma Display Panel.

Image Retention
When a static image is shown on a display for several hours, a
faint imprint of the image, known as image retention, can
remain. This image retention may be temporary or permanent.
Although caused by different things, image retention can
occur on all display technologies, including plasma and LCD.
On today’s plasma displays, permanent image retention is less
of a worry. Most image retention can be improved simply by
watching a motion video sequence.
Image retention, also known as burn-in, can occur in all
phosphor-based display systems (including CRT television
systems–both direct view and projection–as well as plasma
display systems). To avoid image retention or burn-in, do not
show a still image for an extended period. Recommended
guidelines are as follows:
• Do not display static images such as still images, fixed
images from PC or TV game equipment, and/or fixed images
such as time of day indicator or channel logo display for long
periods.
• Do not display content in the 4:3 aspect ratio (black or gray
bars on left and right side of content) or letter-box content
(black bars above and below content) for extended periods of
time, or use either of these viewing modes repeatedly within
a short period of time. This plasma display system is
equipped with multiple wide-screen viewing modes; use one
of these screen modes to fill the entire screen with content.
• Displaying dark images after showing a still image for an
extended time may cause image retention. In most cases,
the image retention can be corrected by displaying bright
images for a similar period of time.
Warning: Displaying a still image on the panel for a long period
of time can cause the image to be burned in to the screen
permanently.

Panel sticking and after-image lag
• Displaying the same images such as still images for a long
time may cause after-image lagging. This may occur in the
following two cases.
1

English

The video program that you watch may be high definition (HD)
or standard definition (SD). This Plasma Display is designed to
scale to either HD or SD signals. If the video program’s
definition type changes while a menu window is displayed on
the screen (for example: HD → SD or SD → HD), the menu size
may temporarily shrink or enlarge until the scaling is complete.
For example, switching between a TV program and an external
digital video recorder (D-VHS) while viewing a menu can cause
the menu window size to fluctuate.

CAUTION

After-image lagging due to remaining electric load

When image patterns with very high peak luminance are
displayed for more than one(1) minute, after-image lagging
may occur due to the remaining electrical load. The afterimages remaining on the screen disappears when moving
images are shown. The time for the after-images to disappear
depends on the luminance of the still image and the length of
time displayed.
2

After-image (lag image) due to burning

Avoid displaying the same image on the Plasma Display
continuously over a long period of time. If the same image is
displayed continuously for several hours, or for shorter periods
but over several days, a permanent after-image may remain on
the screen due to burning of the fluorescent materials. Such
images may become less noticeable if moving images are later
displayed but they do not disappear completely.

NOTE
• When a program menu, TV Guide screen or frozen image is
displayed for 5 to 10 minutes, the system automatically turns
the screen off to prevent damage from screen burning.
• To prevent screen burning, the display position is
automatically changed slightly when the power is switched
on or the input changed. Depending on the broadcast
content, some parts of the picture may not be visible.

Preventing damage from screen burning
• Please show images in full screen unless doing so causes
copyright infringement. See page 65.
• The Energy save function can be set to help prevent screen
burn-in. See page 63.

CAUTION
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART,
STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY
FALL, CAUSING SERIOUS PERSONAL INJURY AND SERIOUS
DAMAGE TO THE PRODUCT. USE ONLY WITH A CART,
STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED BY
THE MANUFACTURER, OR SOLD WITH THE PRODUCT.
FOLLOW THE MANUFACTURER’S INSTRUCTIONS WHEN
INSTALLING THE PRODUCT. ONLY USE MOUNTING
ACCESSORIES RECOMMENDED BY THE MANUFACTURER.
A PRODUCT AND CART COMBINATION SHOULD BE MOVED
WITH CARE. QUICK STOPS, EXCESSIVE FORCE, AND
UNEVEN SURFACES MAY CAUSE THE COMBINED UNIT TO
OVERTURN.

9
En

PDP_PRO1540HD.book Page 10 Wednesday, August 2, 2006 6:01 PM

Safety Precautions
Safety Precautions
This product has been engineered and manufactured with the
highest priority on safety. However, improper use can result in
electric shock and/or fire. To prevent injury, please observe the
following instructions when installing, operating and cleaning
the product. To ensure your safety and prolong the service life
of your product, please read the following precautions carefully
before using the product.
• Read all operating instructions before operating the panel.
• Keep this manual safe for future reference.
• Observe all warnings on the product and in the operating
instructions.
• Follow all operating instructions.
• Cleaning—Unplug the power cord from the wall outlet
before cleaning the product. To clean the product, use the
supplied cleaning cloth or other soft cloth (e.g., cotton,
flannel, etc.). Do not use liquid or aerosol cleaners.
• Do not use attachments unless recommended by the
manufacturer. Use of unauthorized attachments can result
in accidents.
• Do not use the product near water (bathtub, washbasin,
kitchen sink, laundry area, swimming pool, in a wet or damp
basement, etc.).
• Do not place the product on an unstable cart, stand, tripod
or table. Placing the product on an unstable base can cause
the product to fall, resulting in serious personal injuries as
well as damage to the panel. Use only a cart, stand, tripod,
bracket or table recommended by the manufacturer or sold
with the unit. When mounting the product on a wall, follow
the manufacturer’s instructions precisely. Use only
mounting hardware recommended by the manufacturer.
• Sudden stops, excessive pushing and uneven floors can
cause a unit mounted on a cart to fall. Move the cart with
caution.

10
En

• Openings in the cabinet are designed for ventilation. Do not
cover or block these vents and openings since insufficient
ventilation can cause overheating and/or shorten the life of
the panel. Do not place the product on a bed, sofa, rug or
other similar surface since material can block the vents. This
product is not designed for built-in installations. Do not
place the product in an enclosed place such as a bookcase
or rack unless properly vented.
• This product must operate on a power source as stated on
the specification label. If you are not sure of the type of power
supply used in your home, consult your dealer or local power
company.
• Power cord protection—The power cords must be routed
properly to prevent being stepped on or being pinched
between objects. Check entire length of all cables to guard
against pinching.
• This panel contains glass elements. Sudden impacts from
dropping or hitting the panel can break the glass. If the panel
is broken, avoid contact with the glass shards.
• Do not overload AC outlets or extension cords. Overloading
can cause fire or electric shock.
• Never insert objects through vents or openings. High voltage
flows in the product, inserting an object can cause electrical
shock and/or short internal parts. For the same reason, do
not spill water or liquids into the products.

• Do not attempt to service the product yourself. Removing
covers can expose you to high voltage and other dangerous
conditions. Request service from qualified and authorized
service personnel.
• If any of the following conditions occurs, unplug the power
cord from the AC outlet and arrange for repairs with qualified
service personnel.
• power cord or plug is damaged
• liquid spilled or objects fallen into unit
• exposed to rain or water
• product fails to perform as described in the operating
instructions
Do not touch the controls other than those described in
the operating instructions. Improper adjustments can
cause damage, which often requires correction by a
qualified technician
• unit dropped or damaged
• abnormal appearance of picture
• Replacement parts must meet or exceed specifications set
by the manufacturer. Use of unauthorized parts can result in
fire, electric shock and/or other danger.
• Upon completion of service or repair work, request that the
service technician perform periodic safety checks to ensure
that the product is in proper operating condition.
• When mounting the product on a wall or ceiling, install the
panel according to the method recommended by the
manufacturer.
• Keep the product away from heat sources such as radiators,
heaters, stoves and other heat-generating devices (including
amplifiers).
• Unplug the power cord from the wall outlet before installing
the speakers.
• Never expose the screen of the Plasma Display Panel to a
strong impact. The screen may be broken, resulting in fire or
personal injury.
• Do not expose the Plasma Display Panel to direct sunlight
for a long period of time. The optical characteristics of the
front protection panel changes, resulting in discoloration or
warping.
• The approximate weight of each Plasma Display Panel is as
follows:
- PRO-1540HD - 51.5 kg (113.6 lbs.)
- PRO-1140HD - 34.3 kg (75.7 lbs.)
- PRO-940HD - 31.7 kg (69.9 lbs.)
(with stand)
Unpacking, carrying, and installing requires two or more
people.

PDP_PRO1540HD.book Page 11 Wednesday, August 2, 2006 6:01 PM

Safety Precautions

Installation Precautions
Observe the following precautions when installing the panel using optional mounting methods such as the bracket.
• Ask your dealer to perform the installation.
• Use only the supplied bolts.
• For details, see the instruction manual that comes with the optional bracket (or equivalent mounting item).

English

When using the optional brackets or equivalent items

When using other items
• Consult your dealer.
• The following four to six mounting holes can be used for the installation:

Rear view (PRO-1540HD)

Side view
Mounting surface

Mounting
hole
Median line

Mounting
hole

Plasma
Display

Mounting
bracket (or
equivalent item)
M8 screw
12 mm to 18 mm
(0.5 inches to 0.7 inches)

Median line

Rear view (PRO-1140HD)

Mounting
hole

Median line

Rear view (PRO-940HD)

Mounting
hole

Median line

CAUTION
• Use at least four mounting holes symmetrical to the vertical and horizontal median lines.
• Use M8 screws, which go 12 mm to 18 mm (0.5 inches to 0.7 inches) in depth from the mounting surface of the Plasma Display.
See the side view above.
• Be careful not to block rear vents on the Plasma Display.
• Install the Plasma Display on a flat surface to avoid warping the glass.
• The diagrams above show the location of standard mounting screw holes. Holes other than those shown above are for specific
mounting methods and should not be used unless a mounting option’s instructions require their use.

NOTE
• Use the optional PIONEER mounting products whenever possible.
• PIONEER shall not be liable for any personal injury or property damage that results from using mounting items other than the
optional PIONEER products.

11
En

PDP_PRO1540HD.book Page 12 Wednesday, August 2, 2006 6:01 PM

Supplied Accessories
Supplied Accessories

Cleaning cloth

Power cord (2 m/6.6 feet)

Speed clamp × 3

Remote control unit

12
En

Bead band × 3

Warranty card

AA size battery x 2
(Alkaline battery for
remote control unit)

Operating instructions

G-LINK cable (3 m/9.8 feet)

Hexagonal wrench x 1
(Diagonal size: 6 mm)
(for PRO-940HD only)

Ferrite core

Terminal position sheet
(for use when mounting
the Plasma Display on the wall)
(for PRO-1540HD only)

PDP_PRO1540HD.book Page 13 Wednesday, August 2, 2006 6:01 PM

Part Names
Part Names

Plasma Display
English

Front/side view
(PRO-1540HD)

6
7
8

9
13
10

2
3
4
5

(Side view)

1 a POWER button
(See page 26)
2 POWER ON indicator
(See page 26)
3 STANDBY indicator
(See page 26)
4 REC TIMER indicator
5 Remote control sensor

6 STANDBY/ON button
7 INPUT button (ENTER button*)
8 VOLUME UP/DOWN buttons (UP/DOWN
buttons*)
9 CHANNEL UP/DOWN buttons (LEFT/
RIGHT buttons*)
10 TV GUIDE button*
11 USB port
12 INPUT 4 terminals (COMPONENT VIDEO: Y,
CB/PB, CR/PR)
13 INPUT 4 terminal (VIDEO)
14 INPUT 4 terminals (AUDIO)
* ability to operate the TV Guide On Screen™ system.

13
En

PDP_PRO1540HD.book Page 14 Wednesday, August 2, 2006 6:01 PM

Part Names
Front/side view
(PRO-1140HD)

6
7
8

9
13
10

2
3
4

(Side view)

1 a POWER button
(See page 26)
2 POWER ON indicator
(See page 26)
3 STANDBY indicator
(See page 26)
4 REC TIMER indicator
5 Remote control sensor

14
En

PDP_PRO1540HD.book Page 15 Wednesday, August 2, 2006 6:01 PM

Part Names

Front/side view
(PRO-940HD)
English

6
7
8

9
13
10

2
3
4

1
Viewed from below of the display

1 a POWER button
(See page 26)
2 POWER ON indicator
(See page 26)
3 STANDBY indicator
(See page 26)
4 REC TIMER indicator
5 Remote control sensor

Viewed from the front side of the display

(Side view)

15
En

PDP_PRO1540HD.book Page 16 Wednesday, August 2, 2006 6:01 PM

Part Names
Rear view
(PRO-1540HD)

17 18 21 22
11
12
13

25
26
27
28

14
15
16

(Terminals located on the upper
edge of the compartment)

19 20 24

1 PC INPUT terminal (ANALOG RGB)
2 CableCARD™ slot
3 ANT/CABLE A IN terminal
4 ANT B IN terminal
5 AC IN terminal
6 Ethernet cable port
7 HDMI terminals (INPUT 5/INPUT 6)
8 RS-232C terminal (used for factory setup)
9 DIGITAL OUT terminal (OPTICAL)
10 G-LINK terminal
11 INPUT 5 terminals (AUDIO)
12 INPUT 6 terminals (AUDIO)
13 SUB WOOFER terminal
14 INPUT 3 terminals (AUDIO)

16
En

15 INPUT 3 terminals (COMPONENT VIDEO: Y,
CB/PB, CR/PR)
16 INPUT 2 terminals (COMPONENT VIDEO: Y,
CB/PB, CR/PR)
17 INPUT 2 terminal (VIDEO)
18 INPUT 2 terminal (S-VIDEO)
19 INPUT 2 terminals (AUDIO)
20 INPUT 1 terminals (AUDIO)
21 INPUT 1 terminal (S-VIDEO)
22 INPUT 1 terminal (VIDEO)
23 MONITOR OUT terminal (VIDEO)
24 MONITOR OUT terminals (AUDIO)
25 PC INPUT terminal (AUDIO)
26 CONTROL OUT terminal
27 CONTROL IN terminal
28 SPEAKER (R/L) terminals

PDP_PRO1540HD.book Page 17 Wednesday, August 2, 2006 6:01 PM

Part Names

Rear view
(PRO-1140HD)
English

17 18 21 22

11
12
13

25 6

14
15
16

26
27
28

(Terminals located on the upper
edge of the compartment)

19 20 24

1
2
3
4
5
6
7
8
9
10
11
12
13
14

PC INPUT terminal (ANALOG RGB)
CableCARD™ slot
ANT/CABLE A IN terminal
ANT B IN terminal
AC IN terminal
Ethernet cable port
HDMI terminals (INPUT 5/INPUT 6)
RS-232C terminal (used for factory setup)
DIGITAL OUT terminal (OPTICAL)
G-LINK terminal
INPUT 5 terminals (AUDIO)
INPUT 6 terminals (AUDIO)
SUB WOOFER terminal
INPUT 3 terminals (AUDIO)

PDP_PRO1540HD.book Page 18 Wednesday, August 2, 2006 6:01 PM

Part Names
Rear view
(PRO-940HD)

17 18 21 22
11
12
13
14
15
16

25
26
27

(Terminals located on the upper
edge of the compartment)

19 20 24

PDP_PRO1540HD.book Page 19 Wednesday, August 2, 2006 6:01 PM

Part Names

04
9

Remote control unit

1
2
3

4
5
6
7

19
20
21
22
23

9
10

12
13
14
15
16
17

25
26

27
28

29
30

20
21
22
23
24

15
16
17

31
32

Mode switch
(with “TV” selected)

1
2
3
4
5
6

7
8

TV a: Turns ON the Plasma Display Panel or
places it in Standby.
Transmission confirmation LED
INPUT: Selects an input source for the Plasma
Display Panel. (INPUT 1, INPUT 2, INPUT 3, INPUT 4,
INPUT 5, INPUT 6 and PC)
SCREEN SIZE: Selects the screen size.
SLEEP: Sets the sleep timer.
INFO: Displays a channel banner when a TV
program is being watched.
(When the TV Guide On Screen™ system is in
operation, information about the currently
highlighted channel appears on screen (when
available).)
HOME MENU: Displays the Home Menu screen
DAY +/–: Jumps to the next or previous day of
program listings in the TV Guide On Screen™ Listing
service.

25
26
27
28
29
30
31
32

English

This section describes the button functions when the mode is
set to TV. To use the remote for controlling other equipment,
see “Using the remote control unit to control other devices”
starting on page 99.

/ / / : Selects a desired item on the menu
screen
REC: When using the TV Guide On Screen™ System,
triggers recording to a connected VCR
FAVORITE CH (A, B, C, D):
Selects any of the four preset channels (see page 43
for details to set the FAVORITE CH)
While watching, toggle the set channels by
pressing A, B, C and D.
0 – 9: Selects the channel
•(dot): Enters a dot
When entering the number of a sub-channel.
CH +/–: Selects the channel.
SPLIT: Switches the screen mode: 2-screen, picturein-picture, single-screen
FREEZE: Freezes a frame from a moving image.
Press again to cancel the function.
MTS: Selects MTS/SAP or language depending on
the program being watched
D: Lights up all buttons
Lights turn off if no operations are performed within
5 seconds. This is used for remote control use in
dark locations.
ANT: Selects the antenna (A, B) (see page 23 for
details)
AV SELECTION: Selects audio and video settings.
(AV mode: STANDARD, DYNAMIC, MOVIE, GAME,
PURE, USER. PC mode: STANDARD, USER)
DISPLAY: Displays the channel information
TV GUIDE: Displays the TV Guide On Screen™
system
ENTER: Executes a command
PAGE +/– (for the TV Guide On Screen™ system):
Scrolls the program listing screen vertically.
RETURN: Returns to the previous menu screen
MENU: Displays a panel menu in the TV Guide On
Screen™ system
CH ENTER: Executes a channel number
CH RETURN: Returns to the previous channel
This button is disabled while the TV Guide On
Screen™ system is displayed.
VOL +/–: Sets the volume
M MUTING: Mutes the sound
SHIFT: Moves the small screen to a different location
when in the picture-in-picture mode
SWAP: Switches between the two screens when in
the 2-screen or picture-in-picture mode
NOTE

• When using the remote control, aim it at the Plasma Display.
• See pages 92 to 102 for buttons not listed on this page.

19
En

PDP_PRO1540HD.book Page 20 Wednesday, August 2, 2006 6:01 PM

Preparation
Preparation
Installing the Plasma Display

(PRO-1140HD)

Over 50 cm
(19 11/16 inches)
Over
10 cm
(3 15/16
inches)

(PRO-940HD)

Location
• Avoid direct sunlight.
• Maintain adequate ventilation.
• Because the Plasma Display is heavy, have someone help
you when moving or installing the panel.

NOTE
• Allow enough space around the installed Plasma Display
Panel to ensure proper ventilation.

Using the optional PIONEER stand
(for PRO-1540HD and PRO-1140HD)
• For details on installation, refer to the instruction manual
supplied with the stand.

Using the optional PIONEER speakers
(for PRO-1540HD and PRO-1140HD)
• For details on installation, refer to the instruction manual
supplied with the speaker.

Moving the Plasma Display
(PRO-1540HD)

20
En

CAUTION
• These Plasma Display Panels are thin and can be unstable
when held upright. Therefore, at least two people must move
and install these panels.
• Do not hold by the speaker.
• Install the panel on a flat, stable location to avoid warping the
glass components.
• When installing on a rack, etc., someone must steady the
panel at all times.

PDP_PRO1540HD.book Page 21 Wednesday, August 2, 2006 6:01 PM

Preparation

During installation, someone must steady the panel at all
times.

Using a wall for stabilization
1. Attach fall-prevention bolts (hooks) to the
Plasma Display.
2. Use strong cords to firmly attach the panel
to a wall, pillar, or other sturdy
construction.

Stabilize the Plasma Display as shown in the diagram using
screws that are 6 mm (1/4 inch) and at least 20 mm (13/16 inch)
long (available from your dealer or other hardware sources).

3. Repeat attachment for the other side of the
panel.
NOTE

6 mm
(1/4 inch)

Use hooks, cords, and fittings that are available from your
dealer or other hardware sources.
Recommended hook: Nominal diameter 8 mm (3/8 inch)
Length 12 mm to 15 mm (1/2 inch to 5/8 inch)

20 mm min.
(13/16 inch min.)

9 mm to 15 mm
(3/8 inch to 5/8 inch)

Stabilizing on a table or floor

English

Preventing the Plasma Display from
Falling Over

12 mm to 15 mm
(1/2 inch to 5/8 inch)
➀ Hook
➁ Cord
Fitting

CAUTION
The installation site should have adequate strength to support
the Plasma Display. A weak installation site could result in
personal injury and property damage. Please take the
necessary safety measures to prevent it from falling during
emergencies, such as earthquakes or construction accidents.
If you do not take these precautions, the Plasma Display could
fall, causing injury or property damage.
Screws, hooks, chains, and other fittings used to secure the
Plasma Display vary according to the composition and
thickness of the surface to which the panel is attached. Inspect
the mounting surface carefully to determine its thickness and
composition; consult a professional installer if necessary.

21
En

PDP_PRO1540HD.book Page 22 Wednesday, August 2, 2006 6:01 PM

Preparation

Attaching/detaching the PIONEER stand
(for PRO-940HD only)
The PRO-940HD comes with the PIONEER table top stand
attached. You can mount the display in a rack by detaching the
stand. The method for attaching/detaching the stand varies
depending on the particular panel.

CAUTION
• If mounting the panel on a stand, use only the attached
stand for this model. Other stand models are not authorized
for this panel.
• Two or more people are required to assemble and install this
unit.

NOTE
• Install the panel on a flat, stable location to avoid warping the
glass components.

Reattaching the stand

1 Fit the stand’s support columns under the Plasma Display
shown below. Slowly ease the panel down on the
supports.
• Be extremely careful not to insert the stand supports
into any part of the Plasma Display other than the stand
insertion slots. If the panel is mounted improperly, the
communication ports could be damaged or the stand
could be warped.

Detaching the stand

1 Loosen the two installation bolts ➀ using the enclosed
hexagonal wrench.

Line up the column supports with
the bottom of the Plasma Display .
Installation bolts ➀
(M8 x 30 mm: silver)

2 Remove the two installation bolts ➁ using the same

2 Bolt the Plasma Display to the stand at the points
indicated by the arrows.

hexagonal wrench.

Installation bolts ➁
(M8 x 60 mm: silver)
Installation bolts ➁
(M8 x 60 mm: silver)

3 Lift the Plasma Display from the stand.

3 Tighten the installation bolts ➀ firmly using the enclosed
hexagonal wrench.

Installation bolts ➀
(M8 x 30 mm: silver)

NOTE
• Keep the installation bolts ➀ and ➁ for reattaching the
stand to the Plasma Display at a later date.
22
En

• Install the panel on a flat, stable location to avoid warping the
glass components.
• Insert the screws in the holes vertically.
• Do not tighten them with more force than necessary.

PDP_PRO1540HD.book Page 23 Wednesday, August 2, 2006 6:01 PM

Preparation

This system is equipped with two terminals for inputting TV
broadcasting signals, ANT/CABLE A IN and ANT B IN. The
ANT/CABLE A IN terminal accepts both digital and
conventional TV broadcasting signals while the ANT B IN
terminal accepts only conventional TV broadcasting signals.
When using cable TV to watch digital and/or conventional TV
channels, connect to the ANT/CABLE A IN terminal as shown.
To add an outdoor antenna for clearer pictures, connect an
antenna to the ANT B IN terminal. If your outdoor antenna uses
a 75-ohm coaxial cable with an F-type connector, plug it into
the antenna terminal at the rear of the Plasma Display.

Connecting VHF/UHF antennas and a Cable
VHF antenna

Inserting the CableCARD™
The Plasma Display provides a slot for inserting a
CableCARD™. When you are watching digital and/or High
Definition TV channels over cable, the card allows you to use
the cable company’s Point of Deployment (POD) service. This
service presents various types of useful information in Internetstyled text.

English

Cable connections for watching digital
and/or conventional TV channels

1 Confirm that the ANT/CABLE A IN terminal is connected to
the Cable Converter box using a coaxial cable.

2 Slide the slot cover tab on the rear of the Plasma Display
to the left then remove the cover while pulling the tab’s
latch down.

(Viewed from below of the
Plasma Display)

Tab

UHF antenna

U/Vmixer

Coaxial

3 Insert the specified CableCARD™ completely into the slot.

ANT/
CABLE A IN

Plasma Display (rear)
Coaxial
Cable TV
NOTE
NOTE
• Connect coaxial cables as shown above. Signal reception
may fail if cables are connected improperly.
• In order to watch cable TV channels, be sure to connect the
cable to the ANT/CABLE A IN terminal.
• The ANT/CABLE A IN and ANT B IN terminals must not
receive the same signals. For example, do not connect the
cable TV line to both the ANT/CABLE A IN and ANT B IN
terminals. Similarly, do not connect an antenna cable to
both the ANT/CABLE A IN and ANT B IN terminals.
• The TV Guide On Screen™ system may not be available in all
areas and is not available with satellite systems. In addition,
as content providers move to digital programming and
broadcasting, TV Guide data may be unavailable or become
unavailable.

• Be sure to insert only the specified CableCARD™.
• Do not insert a PC card.
• The CableCARD™ automatically generates a cable channel
list. It is unnecessary to activate the “Auto Channel Preset”
option.

Switching between antenna A and B
To watch broadcasts via the two antennas, press ANT on the
remote control.
• While watching a broadcast, press ANT to view the feed from
the other antenna.
• While watching in the 2-screen mode (TV image and video
image) with TV selected, press ANT to view the feed from the
other antenna.
• Pressing ANT while watching in the 2-screen mode with two
TV images displayed has no effect.

23
En

PDP_PRO1540HD.book Page 24 Wednesday, August 2, 2006 6:01 PM

Preparation

Preparing the remote control unit
Inserting batteries
1 Open the battery cover.

Allowed operation range of the remote control
unit
To use the remote control, point it at the sensor located at the
bottom right corner of the Plasma Display. The distance from
the remote control sensor must be within 7 m (23 feet) and the
angle relative to the sensor must be within 30 degrees left or
right.

2 Load the supplied two AA batteries. Insert the negative
polarity (–) ends first.

30º

7m
(23 feet)
30º
Remote control
sensor

• The battery polarities must correspond with the (+) and
(–) indicators in the battery compartment.

3 Close the battery cover.

NOTE
• Although the SR logo also appears in the lower right corner
on the PRO-940HD, the sensor is in the same location for all
three panels.

Cautions regarding the remote control unit

Cautions regarding batteries
• The remote control unit cannot operate the system if the
batteries in the unit are weak. When this happens, replace
the batteries with new ones.
• Use alkaline batteries rather than manganese batteries.
• Do not mix battery brands. Different brands have different
characteristics.
• Do not mix old and new batteries. Mixing old and new
batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Do not leave dead batteries in the remote control. Dead
batteries leak chemicals. If you find any chemical leakage,
wipe thoroughly with a clean cloth.
• The batteries supplied with this product may have a shorter
life expectancy due to storage conditions.
• If you will not use the remote control unit for an extended
period of time, remove the batteries.

Battery disposal
When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.

24
En

• Do not expose the remote control to shock, liquid, or high
humidity.
• Do not place the remote control unit under direct sunlight,
the unit may deform.
• The remote control may not work properly if the panel’s
remote sensor window is under direct sunlight or strong
room lighting. If the remote control fails to function in a
bright environment, try changing the signal angle or move
closer to the panel.
• Objects placed between the remote control and the panel
sensor may block the signal.
• As the batteries become weak, the remote control may need
to be used closer to the panel. Replace the batteries with
new ones if necessary.
• The Plasma Display emits very weak infrared rays from its
screen. Other nearby equipment using an infrared remote
control such as a VCR may receive scrambled or incomplete
commands from its remote control. In this situation, move
the equipment away from the Plasma Display.
• Depending on the environment, infrared rays from the
Plasma Display may corrupt signals sent by the remote
control. These IR waves could also require that the remote
control be used closer to the panel. The strength of infrared
rays emitted from the screen differs, depending on the
image being displayed.

PDP_PRO1540HD.book Page 25 Wednesday, August 2, 2006 6:01 PM

Preparation

Connecting the power cord
English

Connect the power cord last, after all other components are connected.

Plasma Display (rear view)
AC IN terminal is
located on the upper
edge of the
compartment.

Power cord

Noise filter
Partially eliminates noise
caused by the power source.

CAUTION
• Use only the supplied power cord.
• Use only the specified power supply voltage;
neglecting this can result in fire or electric shock.
• For the Plasma Display System, a three-core power
cord with a ground terminal is used for safety
reasons. Always connect the power cord to a
three-pronged outlet and make sure that the cord
is properly grounded.

NOTE
• Always turn the panel’s power OFF when connecting or
disconnecting power cords.
• Disconnect the power cord from the wall outlet when the
Plasma Display Panel is not going to be used for a long
period of time.

Routing cables
When the speakers are installed on the sides
Rear view

Speaker cable

Speed clamp

Speaker cable

Attaching speed clamps to the main unit

Attaching and removing speed clamps

Attach the speed clamps using any of the 4 holes you prefer
(50 inches, 3 holes: 42 inches, 2 holes) marked with an arrow ( )
below, depending on your routing system.
for PRO-1540HD

Insert [1] into an appropriate hole on the rear of the Plasma
Display then snap [2] into the back of [1] to lock the clamp.
Speed clamps are designed to be difficult to release once in
place. Please attach them carefully.
Use pliers to twist the clamp 90º, pulling outward. The clamp
may deteriorate over time and become damaged if removed.
2
1

for PRO-1140HD

NOTE
• Use the supplied speed clamps as necessary.
• Bundle speaker cables so that none are pinched.
for PRO-940HD

25
En

PDP_PRO1540HD.book Page 26 Wednesday, August 2, 2006 6:01 PM

Basic Operations
Basic Operations
Plasma Display
(PRO-1540HD)

Turning on the power
(from Standby)

1 Press a POWER on the Plasma Display if the POWER ON

POWER button

and STANDBY indicators are off.
• The STANDBY indicator on the Plasma Display lights up
red.

POWER ON indicator
STANDBY indicator

2 Press TV a on the remote control unit or STANDBY/ON
on the Plasma Display to turn the system on.
• The POWER ON indicator on the Plasma Display lights
up blue.

(PRO-1140HD)
POWER button

Turning off the power

POWER ON indicator

(to Standby)

STANDBY indicator

1 Press TV a on the remote control unit or STANDBY/ON
on the Plasma Display.
• The system enters the standby mode and the image on
the screen disappears.
• The STANDBY indicator lights up red.
• This allows the system to automatically receive digital TV
program information while in Standby.

(PRO-940HD)

NOTE
• If you are not going to use this system for a long period of
time, unplug the power cord from the power outlet.

POWER ON
indicator

Plasma Display status indicators

STANDBY
indicator

The table below shows the operational status of the Plasma
Display Panel. Panel indicators reflect the current status of the
Plasma Display.
Indicator
Status
POWER ON

System Status

POWER button
Viewed from below of the display (left).

STANDBY
The Plasma Display has been unplugged
or the Plasma Display is off.
Power to the system is on.
The system is in Standby.

For other than the above, see “Troubleshooting”on page 103.

CAUTION
• If the POWER ON and STANDBY indicators are off, the
system cannot be powered ON. Pressing the TV a or
STANDBY/ON button has no effect. Press POWER then wait
for the Standby indicator to light (red).
• The Plasma Display System consumes some power as long
as the plug is inserted into an outlet.

26
En

STANDBY/ON
button

(Right side view)

PDP_PRO1540HD.book Page 27 Wednesday, August 2, 2006 6:01 PM

Basic Operations

Watching TV channels

06
Plasma Display (right side view)
English

TV channels must be programmed into your panel. Refer to
“Setting up TV channels” on page 37.

NOTE
• When watching a digital TV program, you may see
emergency alert messages scrolling at the top of the screen.
Those messages are broadcasted by TV stations as
necessary when in emergency situations.

CHANNEL +/–

Selecting the antenna
After confirming that the Mode switch on the remote control
has been set to “TV”, press ANT on the remote control unit to
select antenna A or B.
• This selection depends on the connections to the panel’s
antenna input terminals (page 23).

Changing channels
To increase the channel number, press CH + on the remote
control. To decrease the channel number, press CH –.
• CHANNEL +/– on the Plasma Display operates the same as
CH +/– on the remote control.
• Press CH RETURN to switch back to the previous channel.
Press CH RETURN again to return to the current channel.

Using 0 – 9 and • (dot) on the remote control unit
Press any combination of buttons 0 to 9 to select a specific
channel. To select subchannels, use the • (dot) button.

EXAMPLE
•
•
•
•
•

To select channel 5 (1-digit channel), press 5.
To select channel 25 (2-digit channel), press 2 then 5.
To select channel 125 (3-digit channel), press 1, 2, then 5.
To select subchannel 10.01, press 1, 0, • (dot), 0, then 1.
To select subchannel 10.001 (for cable TV), press 1, 0,
• (dot), 0, 0, then 1.

NOTE
• After entering a channel or subchannel number, press CH
ENTER to tune in the channel more quickly.
• Each time you change a channel, a channel banner appears
that shows information about the currently selected
channel. To clear the channel banner, press INFO.
• If you do not activate the TV Guide On Screen™ system, the
channel banner may not display certain types of program
information.

Channel banner
12:33pm
DTV 2 • 1002.102 A
XXXXXXXXXX
12:30pm — 2:00pm

XXX

27
En

PDP_PRO1540HD.book Page 28 Wednesday, August 2, 2006 6:01 PM

Basic Operations
Changing the volume and sound

Changing the language

To increase the volume, press VOL + on the remote control. To
decrease the volume, press VOL –.
• VOLUME +/– on the Plasma Display operates the same as
VOL +/– on the remote control.

If you have selected a digital TV program that provides multilanguage services, switch among the languages by pressing
MTS on the remote control.

• To mute the sound output, press MUTING. The symbol “
”
appears on the screen. To return to the previous volume,
press MUTING again. Pressing VOL + also quits muting.

Plasma Display (right side view)
Each time you press MTS, the language switches.

NOTE
VOLUME +/–

Volume adjustment display

Muting display

28
En

• Switchable languages differ depending on the broadcast.
• If the language selected through language setting is
available when the channel or program is changed, you hear
that language.
• If you are watching a digital TV program without sound or
without language information, “N/A” appears on the screen.
If a language other than English, French, or Spanish is
selected, “Others” appears on the screen.

PDP_PRO1540HD.book Page 29 Wednesday, August 2, 2006 6:01 PM

Basic Operations

06
When receiving STEREO sound signals

Setting MTS/SAP mode

NOTE
• Conventional TV channels: TV channels received through the
conventional VHF/UHF frequencies or conventional cable TV
channels
• When stereo sound is difficult to hear, manually switch to
MONO for clearer sound.
• Once MONO is selected, the Plasma Display sound remains
mono even if the system receives a stereo broadcast. You
must reselect STEREO to hear stereo sound again.
• Selecting MTS while the source is from an INPUT (1 to 6) or
a PC does not change the type of sound. The video source
determines the type of sound.

A 125
STEREO

In STEREO mode

English

When watching conventional TV programs, use the Multichannel Television Sound (MTS) function to enjoy stereo sound
and/or Secondary Audio Programs (SAP).
• Stereo broadcasts
Sports, shows, and concerts can be shown with dynamic
stereo sound.
• SAP broadcasts
MAIN sound: The normal program soundtrack (either in
mono or stereo).
SAP sound: Listen to a second language, supplementary
commentary and other information. (SAP is mono sound.)

A 125
STEREO

In SAP mode

A 125
MONO

In MONO mode

When receiving MONO + SAP sound signals
A 125
MONO (SAP)

In STEREO mode

A 125
SAP (MAIN)

In SAP mode

A 125
MONO (SAP)

In MONO mode

When receiving STEREO + SAP sound signals
A 125
STEREO (SAP)

In STEREO mode

Press MTS to cycle through the types of sound.
STEREO mode

SAP mode

MONO mode

A 125
SAP (STEREO)

STEREO

SAP

MONO

In SAP mode

A 125
MONO (SAP)

In MONO mode

NOTE
• The MTS button is disabled while the TV Guide On Screen™
system is displayed.
• In each of the sound types, the display changes according to
the broadcast signals.

When receiving MONO sound signals
A 125
MONO

In STEREO mode

A 125
MAIN

In SAP mode

A 125
MONO

In MONO mode

29
En

PDP_PRO1540HD.book Page 30 Wednesday, August 2, 2006 6:01 PM

Basic Operations

Viewing a channel banner
While watching a TV program, pressing INFO causes a banner
to appear. Pressing INFO again causes the banner to
disappear.

Using the multiscreen functions
Splitting the screen
Use the following procedure to select the 2-screen or picturein-picture mode.
2-screen

12:33pm
DTV 2 • 1002.102

XXXXXXXXXX
12:30pm — 2:00pm

1
2
3
4
5
6
7
8

XXX

Station name
Current time

Picture-in-picture

Channel number
Input (Ant. A or Ant. B)
Program title
Program time schedule
Channel logo
TV rating name or icon

NOTE
• The above information is not displayed unless included in
broadcast signals.
• If you do not activate the TV Guide On Screen™ system, the
channel banner may not display certain types of program
information.

Using the POD service
If you watch digital and/or High Definition TV channels over
cable, you can use the POD service provided by the cable TV
company. This service presents various types of useful
information, using Internet-style text.

1 Press SPLIT to select the display mode.
• Press SPLIT to cycle through the display options: 2screen, picture-in-picture, and single-screen.

Press HOME MENU, 9, 9, then 9 to view the POD display.

30
En

PDP_PRO1540HD.book Page 31 Wednesday, August 2, 2006 6:01 PM

Basic Operations
Freezing images
Use the following procedure to capture and freeze one frame.

Moving image

English

• In 2-screen or picture-in-picture mode, press SWAP to
switch the position of the 2 screens.
The active screen (left side) is indicated by a “ ”
symbol. The active screen’s picture and sound can be
adjusted.

Still image

• In 2-screen mode, press SCREEN SIZE to change the size
of the left screen.
• In picture-in-picture mode, press SHIFT to move the
position of the small screen counter-clockwise.

1 Press FREEZE.
A still image appears on the right screen while action
continues on the left screen.

2 Press FREEZE again to cancel the function.
NOTE

2 To select an input source, press the appropriate input
source button.
• If watching conventional TV, press CH +/– to change the
channel.

• Freeze is not available when watching in Split Screen.
• If this function is not available, a warning message appears.
• Unless another action is taken, FREEZE automatically
cancels after five minutes.
• Displaying pictures in FREEZE mode for an extended period
may cause an after-image.

NOTE
• The SPLIT button is disabled while the TV Guide On Screen™
system is displayed.
• The multiscreen function cannot display images from the
same input source or two external input sources at the same
time. Attempting to do so causes a warning message to
appear.
• Press HOME MENU to return to single-screen viewing. The
corresponding menu appears.
• When the two screens show the same analog broadcasting
coming through antenna A and B, the picture quality may
differ between the two screens.
• If you select 19201080p@24 Hz for the main screen in the
SPLIT mode, video images may not display properly.
• Displaying pictures in multi-screen mode for an extended
period may cause an after-image.

31
En

PDP_PRO1540HD.book Page 32 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Setup
TV Guide On Screen™ System Setup
About the TV Guide On Screen™ system
The TV Guide On Screen™ system is a free, interactive onscreen television program guide. The system offers program
listings, searching by keyword, timer recording, reminders and
more. The TV Guide On Screen™ system is a convenient way to
find out what’s on right now or during the coming week.
Listings can be arranged by channel or by genre. It also allows
you to automatically set your viewing and recording selections
quickly and easily.
Before you can use the TV Guide On Screen™ system, you’ll
need to set it up.

Reminder Screen
If you previously skipped TV Guide setup, the Reminder Screen
appears when you power On the panel.
To make a selection, press / to highlight an option then
press ENTER.
• “Set up TV Guide On Screen now” displays the first setup
screen.
• “Remind me to set it up later” returns you to watching TV.
• “Don’t remind me again” returns you to watching TV and
stops the reminder screen from appearing upon power On.

Legal Notices
In the United States, TV GUIDE and other related marks are registered
marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates.
In Canada, TV GUIDE is a registered mark of Transcontinental, Inc. and is
used under license by Gemstar-TV Guide International, Inc.

NOTE
• The TV Guide On Screen™ interactive program guide
provides listings for cable-ready and digital cable services as
well as conventional broadcasts. It does not provide listings
for satellite services.
• Depending on the current settings and selected items, the
setup screen order may differ from the one given in this manual.
Follow the instructions shown on your panel’s screen.
• TV Guide may not be available in all areas. As content
providers move to digital programming and broadcasting, TV
Guide data may be unavailable or become unavailable.

Setting up the TV Guide On Screen™
system
When the Plasma Display is powered On for the first time, you
are automatically taken through the setup process. Once the
panel’s setup is complete, the TV Guide On Screen™ setup
Welcome Screen appears. Access the TV Guide On Screen™
setup menu from the initial Setup reminder screens, or by
pressing TV GUIDE for the first time.

NOTE
• Once you set up the TV Guide On Screen™ system it may
take up to 24 hours for TV program listings to appear. Initially,
all eight days of listings may take up to one week to load (see
Screen 7).

Welcome Screen
Panel setup includes the TV Guide On Screen™ Welcome
screen.
Or press TV GUIDE to begin setup.
• The Welcome Screen lists features in the Guide.
• Press ENTER to display Screen 1.

32
En

NOTE
• If you decide not to set up the Guide immediately, this
reminder screen appears each time you power On the panel
unless “Don’t remind me again” is selected.

System Setup Screens
NOTE
• Once you start the setup procedure, you cannot return to the
previous screens. If you realize you entered incorrect
information, continue with setup. The last screen of the
procedure gives you the opportunity to correct any mistakes
before you exit TV Guide On Screen™ setup.
Screen 1: Country
• This screen asks for the location of your panel.
• Press / to highlight a country.
• Press ENTER to display Screen 2.

PDP_PRO1540HD.book Page 33 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Setup

Press the number keys or use / to display a number
then / to move to another field.
• Press ENTER to display Screen 3.

Screen 5: Do you have an antenna connected?
• If you select “Yes”, you see Screen 6. (Depending on your
setup configuration, you may see an additional screen. After
that screen, you see Screen 6.)
• If you select “No”, you see Screen 6.

English

Screen 2: Enter ZIP or Postal Code
• If you selected USA in Screen 1, you see the ZIP Code screen.
• Input ZIP Code.

NOTE
• If you selected “No” in Screen 3 then you must select “Yes” in
this screen to receive a channel lineup and listings.

• If you selected Canada in Screen 1, you see the Postal Code
screen.
• Input Postal Code by pressing / to display a character or
number then / to move to another field.
• Press ENTER to display Screen 3.

Screen 6: Are the settings correct?
• If you select “Yes”, you see Screen 7.
• If you select “No”, you see Screen 1.

Screen 3: Do you have Cable?
• If you select “Yes”, you see Screen 4.
• If you select “No”, you see Screen 5.

Screen 7: Congratulations
• Press ENTER to display Screen 8.
Screen 4: Which input terminal is the system plugged
into?
• Select “ANT/CABLE A IN” or “ANT B IN” (automatically
advances to Screen 5 after the selection)

33
En

PDP_PRO1540HD.book Page 34 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Setup
Screen 8: Is a VCR Connected?
• If you select “Yes”, you see Screen 9.
• If you select “No”, you see Screen 14.

Screen 11: VCR Preparation
• Follow the on-screen instructions then press ENTER to
display Screen 12.

Screen 9: VCR Configuration Diagram
• This screen shows the correct way to install the G-LINK cable
from the back of the device to the recording device. Make
sure the G-LINK cable is properly installed.
• Press ENTER to advance to Screen 10.

Screen 12: VCR Code Testing
• When testing is done, Screen 13 displays automatically.

Screen 13: Did your VCR stop playing?

Screen 10: VCR Brand Name
• Press / to select the brand of the recording device.
• Press ENTER to advance to Screen 11.

• If you select “Yes”, you see Screen 14.
• If you select “No”, a different code is tested from Screen 12.

NOTE
• Many VCRs require testing of more than one code to ensure
proper operation with the TV Guide On Screen™ system.
If you select “Test this code again”, the same code from
Screen 12 is sent again.

34
En

PDP_PRO1540HD.book Page 35 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Setup

English

Screen 14: Confirming Your Settings
Verify that the Setup information is correct.
• If it is, select “Yes, end setup” to advance to Screen 15.
• If it is not, select “No, repeat setup process”, to return to
Screen 1.

Screen 15: Congratulations
• You have successfully completed Setup!
• Press ENTER to advance to Screen 16.

Screen 16: Helpful Information
• This screen provides valuable information on using the TV
Guide.
• Press ENTER to watch TV.

35
En

PDP_PRO1540HD.book Page 36 Wednesday, August 2, 2006 6:01 PM

Menu Setup
Menu Setup
PC mode menus

Menu Configuration
AV mode menus

Home Menu

Item

Picture

AV Selection

57
58
58

Home Menu

Item

Page

Contrast

Picture

AV Selection

Brightness

Contrast

Sound

Power Control

Page

Red

Green

Blue

Reset

Brightness

Color

Tint

Sharpness

Treble

Pro Adjust

Bass

Reset

Balance

Reset

Treble

FOCUS

Bass

Front Surround

Balance

Reset

Energy Save

Power Management

FOCUS

Front Surround

Sleep Timer

Energy Save

Option

No Signal off

No Operation off

Sound

Power Control

57
Auto Setup

Manual Setup

Home Media Gallery
Sleep Timer

Option

Position

Auto Size

4:3 Mode

Side Mask

HDMI Input

Monitor Out

70, 71

Digital Audio Out

Language

Parental Control

38 – 42

Favorites

Channel Setup

Closed Captions

43 – 44

Clock

75 – 91

Menu operations
The following describes the typical procedure for setting up the
menus. For the actual procedures, see the appropriate pages
that describe individual functions.

1 Press HOME MENU.
2 Press / (scroll) to select a menu item then press
ENTER.

Tuner Setup

Home Media Gallery

75 – 91

3 Scroll down to the desired submenu item.
• The number of menu layers differs depending on the
menu items.
• If you select “Tuner Setup”, a menu bar appears at the
bottom of the screen. To select a submenu item on the
bar, press / instead of / .

4 Press / to select an option (or parameter) then press
ENTER.
• For some menu items, press

instead of

5 Press HOME MENU to exit the menu.
NOTE
36
En

• To return to the upper menu levels, press RETURN.

/ .

PDP_PRO1540HD.book Page 37 Wednesday, August 2, 2006 6:01 PM

Tuner Setup
Tuner Setup

09
7 Press HOME MENU to exit the menu.

Setting up TV channels

Using Auto Channel Preset
Auto Channel Preset automatically searches and sets up TV
channels. Press ENTER after each selection.

1
2
3
4
5
6

Press HOME MENU.
then ENTER)
then ENTER)

Select “Ant. A” or “Ant. B”. ( /

then ENTER)

Select “Auto Channel Preset”. ( /

then ENTER)

Select “Air” or “Cable”. ( /

Auto Ch. Preset

Auto Channel Preset

This section describes how to manually set up TV channels that
have not been set up by Auto Channel Preset. Press ENTER
after each selection.

then ENTER)

Select “Channel Setup”. ( /

Ant. A

• To restore skipped channels, use the above procedure but
select (add a check mark) a channel in step 6.
• When using the Cable Converter, you may need to manually
add Cable Converter output channels. Press ENTER after
each selection.

Setting up TV channels manually

Select “Tuner Setup”. ( /

Channel Setup Ant. A

NOTE

Cable

Air
Cable

2.0
4.0
6.0

Enter Begin Preset

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

1
2
3
4
5
6

Home Menu Exit

D Cancel

• Channel search automatically starts.

Press HOME MENU.
Select “Tuner Setup”. ( /

Ant. A

then ENTER)
then ENTER)

Select “Channel Setup”. ( /

then ENTER)

Select “Ant. A” or “Ant. B”. ( /

then ENTER)

Select “Add Channel”. ( /

Select a channel number to be added. ( / then ENTER)
• You can also use buttons 0 – 9 to enter a channel
number.
Channel Setup Ant. A

Channel Setup Ant. A

English

This section describes how to search and set up TV channels.
Unless you set up TV channels using Auto Channel Preset, you
may not be able to tune in all available channels.

Add Channel

Auto Ch. Preset Cable
One Moment Please …

Auto Channel Preset • Cable

Ant. A

xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx

• To quit Auto Channel Preset, press D.

7 After Auto Channel Preset finishes, press HOME MENU to

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

000
1

Home Menu Exit

D Cancel

Add Channel

• A confirmation screen appears after ENTER is pressed.

7 Press A to complete the setup process.
8 Press HOME MENU to exit the menu.

exit the menu.

NOTE

NOTE
• When using the Cable Converter, you may need to manually
add Cable Converter output channels.
• When a CableCARD is functioning, select “Ant.B” in step 4
to run Auto Channel Preset.

Setting for skipping unwanted channels
From among TV channels added using Auto Channel Preset,
you can select channels to be skipped using CH+/-. Press
ENTER after each selection.

1
2
3
4
5
6

Press HOME MENU.
Select “Tuner Setup”. ( /

then ENTER)

Select “Channel Setup”. ( /

then ENTER)

Select “Ant. A” or “Ant. B”. ( /

then ENTER)
then ENTER)

Select “Channel Keep/Skip”. ( /

Select a channel to be skipped. ( /
Channel Setup Ant. A
Ant. A

Channel Keep/Skip

then ENTER)

• To include analog channels, manually add these channels.
Digital channels cannot be added manually.

Checking signal strength
When you have selected antenna A, check the current
channel’s signal strength. Also, use this function when
receiving a channel through a VHF/UHF antenna. Press ENTER
after each selection.

1
2
3
4
5

Press HOME MENU.
Select “Tuner Setup”. ( /

then ENTER)

Select “Channel Setup”. ( /
Select “Ant. A”. ( /

then ENTER)

Select “Signal Strength”. ( /
Channel Setup Ant. A
Ant. A

Signal Strength

then ENTER)

Signal Strength
Maximum: 100
Current: 100

Home Menu Exit

Channel Keep/Skip

2.0
4.0
6.0

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

• Adjust the antenna direction to maximize the signal
strength.

6 Press HOME MENU to exit the menu.

• The check mark next to the channel disappears.
37
En

PDP_PRO1540HD.book Page 38 Wednesday, August 2, 2006 6:01 PM

Tuner Setup

Voluntary movie rating system (MPAA)

NOTE

Rating

Description

N/A

Not applicable for MPAA ratings

General audiences. All ages admitted.

Parental guidance suggested. Some material may
not be suitable for children.

PG-13

Parents strongly cautioned. Some material may be
inappropriate for children under 13.

Checking the CableCARD ID

The Plasma Display has a slot for a CableCARD that is used for
managing your information by the cable TV company. The
CableCARD slot is located on the rear of the Plasma Display.
To check your CableCARD ID and the Host ID, follow these
steps.

Restricted. Under 17 requires accompanying
parent or adult guardian (age varies in some
jurisdictions).

NC-17

No one 17 and under admitted.

Not rated.

• This function is available only when receiving digital
broadcasting signals.
• When you use the TV Guide On Screen™ system with a cable
service, select “Cable” for “Auto Channel Preset”.
• Executing more than one scan for cables can cause
broadcast reception to fail.
Age-Base

1
2
3
4
5

Press HOME MENU.
Select “Tuner Setup”. ( /

NOTE

then ENTER)

Select “Channel Setup”. ( /

then ENTER)

Select “POD ID”. ( / )
• The Host ID and CableCARD ID appear.
Press HOME MENU to exit the menu.

• The voluntary movie rating system uses an age-based rating.

TV ratings

Parental Control
With the Parental Control, adults can prevent younger
audiences from watching inappropriate TV programs, VCR
tapes or DVD contents. When an attempt is made to watch a
blocked program (or content), the Plasma Display shows a
message over a black screen. The Parental Control applies to
both conventional and digital TV channels.
There are three rating systems in the United States: the TV
ratings, TV Parental Guidelines, and movie ratings. Movie
ratings are provided by the Motion Picture Association of
America (MPAA) and are used for original movies not edited
for television.
For the rating system in Canada, see page 40.

Rating

Description

TV-Y

All children

TV-Y7

Children 7 and above

TV-G

General audiences

TV-PG

Parental guidance suggested

TV-14

Parents strongly cautioned

TV-MA

Mature audiences only

Age-Base

NOTE
• The system also allows you to select “None”, which blocks
programs with a rating of “None”.

Changing the password
NOTE
• In the U.S. TV Parental Guideline Rating System, programs
with a rating of “None” may be blocked on this product.
Examples of programs with a “None” rating include:
• Emergency Bulletins (such as EAS messages, weather
warning and others)
• Locally originated programming
• News
• Political
• Public Service Announcements
• Religious
• Sports
• Weather
• No Parental Control settings can be entered for INPUT 5 and
INPUT 6.

Using a password prevents others from changing Parental
Control settings. The 4-digit password is 1234. Use the
following procedure to change the password.

1
2
3
4
5

Press HOME MENU.
then ENTER)

Select “Tuner Setup”. ( /

Select “Parental Control”. ( /
Select “Password”. ( /

then ENTER)

Select “Change Password”. ( /
Parental Control

Password

Change Password
Clear Password

then ENTER)

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

6 Enter the current 4-digit password, using the number
buttons.

7 Enter a 4-digit password to be newly set, using the number
buttons.

8 When prompted, enter the same password again.
• A confirmation screen appears.

9 Press A.
38
En

PDP_PRO1540HD.book Page 39 Wednesday, August 2, 2006 6:01 PM

Tuner Setup

10 Press HOME MENU to exit the menu.

• Write down the password and keep it somewhere safe.

Clearing the password
Use the following procedure to clear the password.

1
2
3
4
5

Press HOME MENU.

Select “Parental Control”. ( /

Select “MPAA Ratings”. ( /

Parental Control

Password

Change Password
Clear Password

then ENTER)
then ENTER)

Select the desired rating and change the setting. ( /
then ENTER)
Parental Control

MPAA Ratings

N/A
G
PG

Blocked MPAA Ratings
N/A, G, PG,PG-13, R, NC-17

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

then ENTER)

Select “Clear Password”. ( /

then ENTER)

Select “Parental Control”. ( /

then ENTER)

Select “Tuner Setup”. ( /

Select “Password”. ( /

Select “Tuner Setup”. ( /

English

NOTE

2
3
4
5

• The password entry screen appears.

6 Enter your 4-digit password using the number buttons.

then ENTER)

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

• Each time you press ENTER, the setting is switched.
• A lock icon appears beside the blocked rating.
• The Plasma Display ships with all ratings unblocked.

7 Press HOME MENU to exit the menu.

Home Menu Exit

6 Enter the current 4-digit password, using the number
buttons.
• A confirmation screen appears.

7 Press A.
8 Press HOME MENU to exit the menu.
NOTE
• The above procedure resets the password to the factory
default (1234).

Activating the Parental Control
1 Press HOME MENU.
2 Select “Tuner Setup”. ( / then ENTER)
3 Select “Parental Control”. ( / then ENTER)
4 Select “Status”. ( / then ENTER)
5 Select “On”. ( / then ENTER)

NOTE
• Blocking a rating causes more severe ratings to be
automatically blocked as well. Likewise, unblocking a rating
causes less severe ratings to be automatically unblocked.

Setting the TV ratings
1 Press HOME MENU.
2 Select “Tuner Setup”. ( / then ENTER)
3 Select “Parental Control”. ( / then ENTER)
4 Select “TV Ratings”. ( / then ENTER)
5 Select the desired rating and change the setting. ( /
then ENTER)

Parental Control
TV Ratings

Setting the voluntary movie rating system
(MPAA)
1 Press HOME MENU.

Blocked TV Ratings

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

• The password entry screen appears.

6 Enter your 4-digit password using the number buttons.
7 Press HOME MENU to exit the menu.

TV Ratings
TV-None
TV-Y
TV-Y7
TV-G
TV-PG

• The password entry screen appears.

6 Enter your 4-digit password using the number buttons.
• Each time you press ENTER, the setting is switched.
• A lock icon appears beside the blocked rating.
• The Plasma Display ships with all ratings unblocked.

7 Press HOME MENU to exit the menu.

We suggest you write down your password and keep in a safe place.

PRO-1540HD/PRO-1140HD/PRO-940HD
Your password No.:

If you forget the password
When the message “Enter your Password” is displayed in step 6
under “Clearing the password”, press the ENTER button on the
remote control unit and hold it down for 3 seconds or longer.
The password reverts to “1234”.

39
En

PDP_PRO1540HD.book Page 40 Wednesday, August 2, 2006 6:01 PM

Tuner Setup

NOTE

Canadian rating systems

• Blocking a rating causes more severe ratings to be
automatically blocked. Likewise, unblocking a rating causes
less severe ratings to be automatically unblocked.

Setting the TV Parental Guidelines (TV
Guidelines)
1 Press HOME MENU.
2 Select “Tuner Setup”. ( / then ENTER)
3 Select “Parental Control”. ( / then ENTER)
4 Select “TV Parental Guidelines”. ( / then ENTER)
5 Select the desired rating and change the setting. ( /

Choose either the Canadian English ratings or the Canadian
French ratings. These ratings are based on the Canadian
Radio-Television and Telecommunications Commission
(CRTC) policy.

Canadian English ratings
Rating

Description

Exempt: Includes news, sports, documentaries
and other information programming; talk shows,
music videos, and variety programming.

Children: Intended for younger children under the
age of 8 years. Pays careful attention to themes
that could threaten their sense of security and
well-being.

C8+

Children over 8 years old: Contains no portrayal of
violence as the preferred, acceptable, or only way
to resolve conflict; nor encourages children to
imitate dangerous acts which they may see on the
screen.

General: Considered acceptable for all age
groups. Appropriate viewing for the entire family,
contains very little violence, physical, verbal or
emotional.

Parental Guidance: Intended for a general
audience, but may not be suitable for younger
children (under the age of 8) because it could
contain controversial themes or issues.

14+

Over 14 Years: Could contain themes where
violence is one of the dominant elements of the
storyline, but it must be integral to the
development of plot or character. Language usage
could be profane and nudity present within the
context of the theme.

18+

Adults: Intended for viewers 18 years and older
and might contain depictions of violence, which
while related to the development of plot, character
or themes, are intended for adult viewing. Could
contain graphic language and portrayals of sex
and nudity.

then ENTER)

Parental Control

TV Parental Guidelines

Fantasy Violence
Violence
Sexual Situations

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

Blocked TV Parental Guidelines

Home Menu Exit

• The password entry screen appears.

7 Press HOME MENU to exit the menu.

Age-Base

Blocking Not Rated TV programs
Use the following procedure to block TV programs whose
rating information is unavailable.

1
2
3
4
5

Press HOME MENU.
Select “Tuner Setup”. ( /

then ENTER)

Select “Parental Control”. ( /

then ENTER)

Select “Unavailable Ratings”. ( /

then ENTER)

Select “Block” or “Don’t Block”. ( /
Parental Control
Unavailable Ratings

then ENTER)

Unavailable Ratings

Block
Don’t Block

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

• The password entry screen appears.

6 Enter your 4-digit password using the number buttons.
• The Plasma Display ships with all ratings unblocked.

7 Press HOME MENU to exit the menu.

40
En

PDP_PRO1540HD.book Page 41 Wednesday, August 2, 2006 6:01 PM

Tuner Setup

Canadian French ratings
Description

Exempt programming.

General: All ages and children, contains minimal
direct violence, but may be integrated into the plot
in a humorous or unrealistic manner.

8ans+

General but inadvisable for young children: May
be viewed by a wide public audience, but could
contain scenes disturbing to children under eight
who cannot distinguish between imaginary and
real situations. Recommended for viewing with
parent.

Age-Base

Setting Canadian French ratings
1 Press HOME MENU.
2 Select “Tuner Setup”. ( / then ENTER)
3 Select “Parental Control”. ( / then ENTER)
4 Select “Canadian French Ratings”. ( / then ENTER)
5 Select the desired rating and change the setting. ( /
then ENTER)

Parental Control
Canadian French Ratings

13ans+

Over 13 years: Could contain scenes of frequent
violent scenes and therefore recommended for
viewing with parent.

16ans+

Over 16 years: Could contain frequent violent
scenes and intense violence.

18ans+

Over 18 years: Only for adult viewing. Could
contain frequent violent scenes and extreme
violence.

English

Rating

Canadian French Ratings
E
G
8 ans+

Blocked Canadian French Ratings xxxxxxxxxxxxxxxxxxxxx
E, G, 8 ans+, 13 ans+, 16 ans+, 18 xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
ans+
Home Menu Exit

• The password entry screen appears.

7 Press HOME MENU to exit the menu.
Setting Canadian English ratings
1 Press HOME MENU.
2 Select “Tuner Setup”. ( / then ENTER)
3 Select “Parental Control”. ( / then ENTER)
4 Select “Canadian English Ratings”. ( / then ENTER)
5 Select then change to the desired rating. ( / then
ENTER)

Parental Control
Canadian English Ratings

Canadian English Ratings

E
C
C8+

xxxxxxxxxxxxxxxxxxxxx
Blocked Canadian English Ratings xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

• The password entry screen appears.

7 Press HOME MENU to exit the menu.
NOTE
• Blocking a rating causes more severe ratings to be
automatically blocked. Likewise, unblocking a rating causes
less severe ratings to be automatically unblocked.

NOTE
• Blocking a rating causes more severe ratings to be
automatically blocked. Likewise, unblocking a rating causes
less severe ratings to be automatically unblocked.

Setting new ratings
Digital broadcasts now carry new ratings that are not
compatible with the Plasma Display Panel’s original Parental
Control settings. When you first tune in one of these
broadcasts, a New Parental Control menu appears on the
screen. This tells you that you must now change your Parental
Control settings to handle these new ratings. Otherwise,
previously blocked ratings may become unblocked.

1 Press HOME MENU.
2 Select “Tuner Setup”. ( / then ENTER)
3 Select “Parental Control”. ( / then ENTER)
Parental Control

Status

Status
MPAA Ratings
TV Ratings

New XXXXXXXXXXXXX

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

• The new menu is displayed when Status is selected. The
message “Regional ratings have changed. Set Parental
Control ratings again.” appears on the right of the
screen.

41
En

PDP_PRO1540HD.book Page 42 Wednesday, August 2, 2006 6:01 PM

Tuner Setup

4 Select and change the desired rating. ( / then ENTER)
Parental Control
Unavailable Ratings
New (xxx)
New (xxx)
New (xxx)
Password

New (xxx)

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

XX
XX

Home Menu Exit

• The menu appears between “Unavailable Ratings” and
“Password”.
• The password entry screen appears.

5 Enter your 4-digit password using the number buttons.
• Each time you press ENTER, the setting is switched.
• A lock icon appears beside the blocked rating.
• When you are finished, the word “New” disappears from
the Parental Control menu.

6 Press HOME MENU to exit the menu.

Temporarily deactivating the Parental Control
When the activated Parental Control senses a blocked TV
program (or content), the Plasma Display shows a message
over a blank screen.
The method for temporarily deactivating the Parental Control
differs, depending on the selected input source.

Antenna A or antenna B:
The following screen appears. Press ENTER.
Parental Control
WWWWWWW
1000.0000
(Ant. B)

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

Enter Disable Parental Control

Enter your 4-digit password.
Parental Control

Enter your Password

Deleting new ratings

A Clear Entry

You can delete a New Parental Control menu. When the menu
is deleted, all blocks are removed.

1
2
3
4

Press HOME MENU.
Select “Tuner Setup”. ( /

then ENTER)

Select “Parental Control”. ( /

Parental Control

Status

Change
Off Password
Clear Password
Enter your Password
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
A Clear Entry

then ENTER)

D Cancel

Home Menu Exit

Parental Control

Status

Change
Off Password
____
Clear Password
Reset Digital regional ratings?
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

D Cancel

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxx
xxxxxxxx
Home Menu Exit

• The New Parental Control menu remains. However, if no
settings are entered within 60 seconds, the selection
screen for deleting new ratings disappears.

7 Press HOME MENU to exit the menu.
NOTE
• Broadcasts with new (arriving) ratings are not reflected while
the Parental Control menu is open.
• Blocking a rating causes more severe ratings to be
automatically blocked. Likewise, unblocking a rating causes
less severe ratings to be automatically unblocked.

Enter your 4-digit password. Pressing ENTER again causes the
password entry screen to disappear.
Please Input Your Password.

5 Enter your 4-digit password using the number buttons.
6 Select A for “Accept” or D for “Cancel”.

• The password entry screen appears for approximately 60
seconds. If the screen disappears prematurely, press ENTER
to reveal the screen again.

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxx
xxxxxxxxxxx

• The password entry screen appears.

A Accept

D Cancel

Input 1 – 4:

then ENTER)

Select “Status” and then “Off”. ( /

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

• The above password entry screen also appears during 2screen mode, picture-in-picture, and while freezing an
image.
• The password entry screen appears for approximately 60
seconds. After the screen disappears, pressing ENTER
causes it to appear again.

PDP_PRO1540HD.book Page 43 Wednesday, August 2, 2006 6:01 PM

Tuner Setup

Setting your favorite channels
1
2
3
4
5

Press HOME MENU.
Select “Tuner Setup”. ( /
Select “Favorites”. ( /

then ENTER)

Select a color button (A, B, C, D). ( /

then ENTER)

Select a TV channel to be registered. ( /

Closed Captions

then ENTER)

Status
Favorites
Favorites A

Favorites A
B
8.0
A
9.0
B
9.0
A 11.0
B 11.0

Current Favorites A Line Up
B0008.000
A0009.000
A0011.000

Status
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

Off
On
On If Mute

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

Home Menu Exit

Item

Home Menu Exit

Setting up closed captions
Your Plasma Display System is equipped with an internal
closed caption decoder. Closed caption allows you to view
conversations, narration, and sound effects in TV programs
and home videos as subtitles on your Plasma Display screen.
Many digital TV programs also offer closed captioning. Digital
closed captions support changing parameters such as fonts
and colors.
• Not all programs and videos offer closed caption. Please look
for the “
” symbol to check for closed captioning on a
program or video.

Description

Off
Does not show closed captions
(factory default)

• A star appears beside the favorite channels currently
selected.
• To register another TV channel under the same color
button, repeat step 5. To register another TV channel
under a different color button, repeat steps 4 and 5.

6 Press HOME MENU to exit the menu.

English

Set up to 10 TV channels for each of the four color buttons on
the remote control (40 channels in total).

Activating the closed caption
1 Press HOME MENU.
2 Select “Tuner Setup”. ( / then ENTER)
3 Select “Closed Captions”. ( / then ENTER)
4 Select “Status”. ( / then ENTER)
5 Select “On” or “On If Mute”. ( / then ENTER)

Always shows closed captions

On If Mute

Shows closed captions only when sound is being
muted

6 Press HOME MENU to exit the menu.
Selecting the type of conventional closed
captions
Select a conventional TV channel before deciding on a type of
closed captioning. Some digital TV programs provide only
conventional closed captions.
• “CC1”, “CC2”, “CC3”, or “CC4” displays subtitles of TV dramas
and news programs while allowing a full view of the picture.
• “Text1”, “Text2”, “Text3”, or “Text4” superimposes information
over the picture (e.g. TV guide, weather) that is independent
from the TV program in progress.

1
2
3
4
5

Press HOME MENU.
Select “Tuner Setup”. ( /

then ENTER)

Select “Closed Captions”. ( /

then ENTER)

Select “Analog Settings”. ( /

then ENTER)

Select the desired closed caption. ( /
Closed Captions
Analog Settings

Analog Settings
CC1
CC2
CC3
CC4
Text 1

then ENTER)

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

• The factory default is “CC1”.

6 Press HOME MENU to exit the menu.

43
En

PDP_PRO1540HD.book Page 44 Wednesday, August 2, 2006 6:01 PM

Tuner Setup

Selecting digital closed captions

The following table shows the available parameters for each
item.

Use the following procedure to select digital closed captions:
Service 1 to 6.

Item

Selection

Press HOME MENU.

Font Size

Auto/ Large/ Standard/ Small

Select “Tuner Setup”. ( /

Font1

Auto/ Font 1/ Font 2/ Font 3/ Font 4/ Font 5/ Font 6/
Font 7

Font Color

Auto/ Black/ White/ Red/ Green/ Blue/ Yellow/
Magenta/ Cyan

Font Opacity

Auto/ Solid/ Transparent/ Translucent/Flashing

Background
Color

Auto/ Black/ White/ Red/ Green/ Blue/ Yellow/
Magenta/ Cyan

Background
Opacity

Auto/ Solid/ Transparent/ Translucent

1
2
3
4
5
6

then ENTER)

Select “Closed Captions”. ( /
Select “Digital Settings”. ( /

then ENTER)
then ENTER)
then ENTER)

Select “Digital Service”. ( /

Select the desired closed caption. ( /
Closed Captions
Digital Settings

Digital Settings
Digital Service

then ENTER)

Digital Service
Service 1
Service 2
Service 3
Service 4
Service 5

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

Home Menu Exit

Font 1 (monospaced with serifs)/ Font 2 (proportionally spaced with serifs)/
Font 3 (monospaced without serifs)/ Font 4 (proportionally spaced without serifs)/ Font 5 (casual font)/ Font 6 (cursive font)/ Font 7 (small capitals font)

With “Auto” selected, parameters specified by the provider are
used. If not specified by the provider, the bolded default
parameters are used. Selected parameters override any other
parameters, including those from the provider.

• The factory default is “Service 1”.

7 Press HOME MENU to exit the menu.
NOTE
• When available, the Primary Caption Service is usually
offered for Service 1, and the Secondary Language Service is
usually offered for Service 2.

Selecting digital closed caption parameters
Use the following procedure to change digital closed captions
parameters such as font size, font type, foreground and
background colors.

1
2
3
4
5

Press HOME MENU.
Select “Tuner Setup”. ( /

then ENTER)

Select “Closed Captions”. ( /
Select “Digital Settings”. ( /

then ENTER)
then ENTER)

Select “Font Size”, “Font”, or any other item. ( /
ENTER)

then

Clock Setting
With “Auto Set” selected for Clock Setting, the system acquires
and sets the time automatically. You can also manually set the
time. If power is lost (unplugged or power outage), the set time
is cleared.

1
2
3
4
5

Press HOME MENU.
Select “Tuner Setup”. ( /
Select “Clock”. ( /

then ENTER)

Select “Time Zone”. ( /

then ENTER)

Select a time zone for your area. ( /
Clock
Time Zone

6 Select the desired parameter. ( / then ENTER)

then ENTER)

Time Zone
Atlantic
Eastern
Central
Mountain

Current Time:
9:55 pm EDT
Monday
05/17/04

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

Closed Captions

Digital Settings

Font Size

Font Size
Large
Standard
Small

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

7 Repeat steps 5 and 6 as necessary. ( , / )
8 Press HOME MENU to exit the menu.

6 Select “D.S.T.”. ( , / , then ENTER)
7 Select “Applies” or “Does Not Apply”. ( / then ENTER)
• Set this option if your area uses Daylight Savings Time.
Clock
D.S.T.

Daylight Savings Time
Applies
Does Not Apply

Current Time:
9:56 pm EDT
Monday
05/17/04

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

8 Select “Auto/Manual Set”. ( , / , then ENTER)
9 Select “Auto Set” or “Manual Set”. ( / then ENTER)

44
En

PDP_PRO1540HD.book Page 45 Wednesday, August 2, 2006 6:01 PM

Tuner Setup

10 If you chose “Auto Set”, select an antenna (A or B) and a
channel number using
Auto/Manual Set

Auto/Manual Set •Auto Set

and ENTER.

Clock Set Channel
Ant. A

2.0

Current Time:
11:58 pm PDT
Monday
05/17/04

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx

English

Clock

Home Menu Exit

• The date and time is corrected automatically using data
from the selected channel.
If you select “Manual Set”, manually set the date and time
using / , / and ENTER.
Clock

Auto/Manual Set

Auto/Manual Set •Manual Set

Date and Time
3
4
3 /17/04 11:58pm
5
6

Current Time:
11:58 pm PDT
Monday
05/17/04

xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu Exit

11 Press HOME MENU to exit the menu.
NOTE
• If the TV Guide On Screen™ system is active, the Plasma
Display accesses time through the TV Guide On Screen™
system. When the TV Guide is providing the time data, you
cannot set up the clock using the menu. If you select a
parameter for the Clock menu then press ENTER, the menu
screen disappears and a dialog box appears. Press A to clear
the dialog box.

45
En

PDP_PRO1540HD.book Page 46 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation
TV Guide On Screen™ System Operation
Using the TV Guide On Screen™ system
Before you can use the TV Guide On Screen™ system, you’ll
need to set it up. If you haven’t already done this, please turn to
“TV Guide On Screen™ System Setup”on page 32 before
proceeding.
In order to record TV programs with a VCR, you need to
correctly connect the equipment to the Plasma Display. For
VCR connection information, see page 71.

TV Guide On Screen™ icons
Various icons are used to convey information or show the
status of an item. These icons can be on the Info Bar, inside the
Info Box, or beside program titles.
•

Info icon – Alerts that additional information is
available (press INFO to display)

•

Progress Bar – Shows the elapsed time of the
current program

•

HDTV – Indicates that a program is a high-definition
broadcast

NOTE
• The TV Guide On Screen™ interactive program guide
provides listings for cable-ready and digital cable services as
well as conventional broadcast. It does not provide listings
for satellite services.
• Once the TV Guide On Screen™ system is activated it may
take up to 24 hours to begin receiving TV program listings.
Initially, of all eight days of listings may take up to one week
to load.
• TV Guide may not be available in all areas. As content
providers move to digital programming and broadcasting, TV
Guide data may be unavailable or become unavailable.

Screen components
Many of the screens have common elements to make using the
system easier.
1

New – The program is new (not a repeat)

•

Stereo – The program is broadcast in stereo

•

CC – The program is broadcast with closed captioning

•

TV Rating – Indicates the age rating for the program

•

Record Daily – Records the same channel and time
every Monday through Friday (manual recording only)

•

Record Regularly – Records the same program any day
it airs on the same channel at the same time

•

Record Weekly – Records a program every week at the
same time/day

•

Record Suspend – The program is set to record, but is
suspended because of a conflict with another recording or
auto tune reminder. The recording resumes when the
conflict is cleared.

•

Record Off – The program remains in the SCHEDULE
list but is not recorded until the frequency is changed to one
of the above

9
7
8

1
2
3
4
5
6
7
8
9
10
11
12
13

46
En

TV GUIDE logo
Clock – Shows the current time
Time slot – Half-hour time slots are displayed horizontally
Time tab – Indicates the currently selected time slot
Current service label – Indicates the currently selected
service
Service bar – Gives access to the various TV Guide
services.
Title – Shows the title of the TV program
Info Bar – Shows various icons to convey information or
show the status of an item
Video window – Allows you to continue watching the
current program while using the Guide
Panel ads and panel menu entry – Space for show or
product advertising (and the panel menu)
Channel logo
Info Box – Shows information about the highlighted item
Channel ads – Space to advertise upcoming programs and
specials

Record Once – One-time only recording

•

Remind Once – One-time only reminder

•

Remind Daily – Reminds for the same channel and time
every Monday through Friday (manual reminder only)

•

Remind Regularly – Reminds the same program any
day it airs on the same channel at the same time

•

Remind Weekly – Reminds every week at the same
time/day

•

Remind Suspend – A reminder is set for the program,
but is suspended because of a conflict with another auto
tune reminder or recording. The reminder resumes when the
conflict is cleared.

•

Remind Off – The program remains in the SCHEDULE
list but the reminder is held until the frequency is changed to
one of the above.

PDP_PRO1540HD.book Page 47 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation
TV Guide On Screen™ navigation

Key

What it does

TV GUIDE

Press to display the TV Guide On Screen™ system
(also use to exit).

ENTER

Use to navigate screens (highlight an item)
Press to confirm a selection or execute an action
Can also be used to display the panel menu when
a future program is highlighted

Press to display a panel menu

INFO

Press to cycle through the available information
for the current program or screen

 REC

Press to set the highlighted program to record

Number buttons

Use for numeric entry

PAGE +/–

Press to select the previous/next page of
information (where applicable)

DAY +/–

Press to jump to the next/previous day of program
listings (if applicable)

The Listings screen
The Listings screen is the main menu for the TV Guide On
Screen™ system. This is the screen you see when you press TV
GUIDE.
Options on the Listings screen include:

•
•
•
•
•
•
•

English

The table below summarizes the TV Guide On Screen™ system
navigation buttons for the remote control.

View eight days of program listings.
Display information about individual programs.
Select a program to start watching.
Set a reminder about a program.
Set a program to record.
See a thumbnail of any channel in the video window.
Access panel and channel ads.

1 Press TV GUIDE to display the Listings screen.

You can also use the panel’s buttons, TV GUIDE, ENTER, UP/
DOWN, and LEFT/RIGHT to make selections. The UP/DOWN
and LEFT/RIGHT buttons operate the same as the / and /
buttons on the remote control.

• With “LISTINGS” highlighted in the Service bar (top of
the screen), press INFO to display (then close) Help
information.
• Press TV GUIDE anytime to exit.

2 Press / / / to navigate the Listings screen.
• With a program highlighted, press ENTER to start
watching that program.
• Move right for programs showing at later times.
• Press PAGE+/– to scroll one menu page at a time.
• Press INFO to display additional information (if
available) about the currently selected show.
• Press DAY+/– to jump to the next/previous day in the
listings grid.

3 To set the highlighted program to record, press  REC.

Pressing  REC just once sets the program to record. Press 
REC repeatedly to change the frequency of the recording:
•
•

Once – Just records the highlighted program
Regularly – Records the same program any day it airs
on the same channel at the same time1

47
En

PDP_PRO1540HD.book Page 48 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation

Weekly – Records the same program at the same time1/
day every week
• No record icon – Does not record.
•

The program is recorded if it starts any time up to the midway
point of the originally scheduled program. For example, up to
9:15 for a 9:00 to 9:30 program.
These recording options use the default settings.
To record using settings other than the defaults, use the panel
menu recording option described below.

NOTE
• When TV Guide On Screen™ is not being displayed, you can
record a program simply by pressing the REC button on the
remote control. Press the REC button to record the current
program episode. Recording begins immediately. If the
program is listed in the TV Guide On Screen™, recording
stops at the end of the program. If the program is not listed
in the TV Guide On Screen™ system, recording continues for
30 minutes.
• When TV Guide On Screen™ is not displayed, pressing the
REC button more than once has no effect.

3 Highlight “set recording” then press ENTER.
4 Set the recording options:
Press / to highlight a field then press / to change
the setting.
• frequency – select whether the program will be
recorded Once, Regularly (at the same time on the
same channel), or Weekly (every week at the same
time/day). The Off option adds the program to the
recording schedule but doesn’t record it (you can set it
to record later).
• start – set the start time of the recording to On time, or
up to 120 minutes before or after the scheduled time.
• end – set the end time of the recording to On time, or
up to 120 minutes before or after the scheduled time.
• recorder – select a recorder to be used for recording.
• If you want to cancel the recording, highlight cancel
then press ENTER.

5 Once all the settings have been made, press ENTER to

highlight “schedule recording” then press ENTER again.

Recording programs
The simplest way to record a program is to highlight it then
press  REC (as described above). However, if you want to set
the recording options to anything other than the default, use
the Recording Options panel menu. Here you can adjust the
start and end times, the destination of the recording, etc.

1 From LISTINGS, SCHEDULE, or SEARCH, highlight the
program you want to record.
• The recording is now set (listed in SCHEDULE) and the
appropriate icon appears on the show title.
If there is a time conflict with a previously scheduled recording
or auto-tune reminder, you will be alerted by one of the
messages below. You can select to record the conflicting
program, or cancel the recording.

2 Press MENU to display the Episode Options menu.

48
En

PDP_PRO1540HD.book Page 49 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation
When the recording is about to start

Setting program reminders
By setting a program reminder you can have the TV alert you
when a program is about to start on another channel. You can
set reminders for individual episodes, or for every time a
program airs.

English

The TV Guide On Screen™ system alerts you when a scheduled
recording is about to start and gives you the chance to cancel
the recording.
When you see the on-screen alert, select the next action;
• “change channel, start recording”
• “don’t change channel; cancel recording”

1 From LISTINGS, SCHEDULE, or SEARCH, highlight the
program.

Depending on the situation, the following screens may appear.
4-+

Timer Alert

The following timer is about to begin:
Tues. 12/30 12:30am-12:59am
Ant. A 1000.000 BRAV022
A Accept

4-+

D Cancel Timer

Timer Alert

PLASMA DISPLAY

The following timer is about to begin:

2 Press MENU to display the Episode Options menu.

1/5 4 : 06am- 9 : 08am
Ant. A 1000. 5 BRAV022
Wed.

D Cancel Timer

A Accept

Press A to start recording as scheduled or D to cancel
recording.

While recording is in progress
If you attempt to change the channel during recording, the
following screen appears.
Select the next action:
• “don’t change; keep recording”
• “change; stop recording”

Depending on the situation, the following screens may appear.
This reminder remains on-screen for 15 seconds.
4-+

Recording In Progress

Changing channels will interrupt a recording in progress.
A Change Channel Now

REC

Recording In Progress

D Don't Change Channel

PLASMA DISPLAY

3 Highlight “set reminder” then press ENTER.
4 Set the reminder options.
Press / to highlight a field; press / to change the
setting.
• frequency – select whether to be reminded just Once,
Regularly (at the same time on the same channel), or
Weekly (every week at the same time/day). The Off
option adds the program to the reminder schedule but
no reminder is given (to be set later).
• auto tune – choose whether the TV should
automatically change channels when a reminder is due.
• when – set when the reminder appears (before, on time,
or after a program has started).

Changing channels will interrupt a recording in progress.

A Change Channel Now

D Don't Change Channel

Press A to change the channel and quit recording; or press D
not to change the channel and to continue recording.

49
En

PDP_PRO1540HD.book Page 50 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation
5 Once all the settings have been made, press ENTER to

highlight “schedule reminder”, then press ENTER again.

Depending on the situation, the following screens may appear.
The reminder remains on-screen for 15 seconds.
Timer Alert
Tues. 12/30 12:30am-12:59am
Ant. A 1000.000 BRAV022
A Accept

D Cancel Timer

Timer Alert

PLASMA DISPLAY

Wed. 1/5
4 : 06am- 9 : 08am
Ant. A 1000. 5 BRAV022
D Cancel Timer

A Accept

• The reminder is now set (listed in SCHEDULE) and the
appropriate icon appears on the show title.
If there is a time conflict with a previously scheduled auto-tune
reminder or recording, you will be alerted. One of the
messages below will appear. You can select to set a reminder
for the conflicting program or cancel the reminder.

Press A to leave the reminder in effect, or D to dismiss the
reminder.

When scheduled reminder is due (auto-tune is ON)
If the “auto-tune” setting was set to “yes” in the Remind
Options, one of the following screens appears, depending on
the situation.
The screen remains visible for 15 seconds.
Timer Alert
Tues. 12/30 12:30am-12:59am
Ant. A 1000.000 BRAV022
A Accept

Timer Alert

PLASMA DISPLAY

Wed. 1/5
4 : 06am- 9 : 08am
Ant. A 1000. 5 BRAV022
A Accept

Press A to make the Timer Alert screen disappear.

When a scheduled reminder is due (auto-tune is OFF)
Depending on your settings, the reminder will appear on your
TV screen shortly before the program is scheduled to start. This
happens when you have selected “NO” for the auto tune. The
reminder remains on-screen for three minutes before it
automatically disappears.
Press ENTER to switch to the highlighted program in the
reminder or highlight “hide reminders” to dismiss the reminder.

If more than one reminder is set for the same time, press
to select which program to watch.

50
En

PDP_PRO1540HD.book Page 51 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation

Searching for programs

4 Press ENTER to list upcoming programs that match the
categories you chose.
English

The Search screen lets you search for programs alphabetically,
by category, or by keyword. You can also search for HDTV
programs.

Searching by category
This option supports searching for programs by category, and
then by a further sub-category.

1 Select “SEARCH” from the Service bar at the top of the
screen.

2 Press
/

to move to the search category bar, then press
to select a search category.

5 Highlight a program listing then press MENU to display
the Episode Options menu.

• Available categories may include:
• Movies
• Sports
• Children
• Educational
• News
• Variety
• Series
• HDTV

• If the program is currently showing, press ENTER to start
watching it immediately.

3 Press

to highlight the search sub-categories then select
a sub-category.

• Sub-categories availability depends upon the category
you choose.

51
En

PDP_PRO1540HD.book Page 52 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation
Searching by keyword

7 Input the keyword for the search.

This option supports searching for shows based on keywords
you enter. The keywords you create are stored so you can use
them again.

1 Select “SEARCH” from the Service bar at the top of the
screen.

2 Press
/

to move to the search category bar, then press
to select “KEYWORD”.

• Highlight characters by pressing / / / , then press
ENTER to input the letter or number.
• The new keyword is stored for future searches.

8 Select “DONE” to start the search process.
9 Highlight a program listing, then press MENU to display
the Episode Options menu.
• Previously entered keywords are displayed. Simply
select one to search for it again.
• To edit or delete a keyword, highlight it then press
MENU. From the panel menu you can choose “edit
search” or “delete search”.

3 Press ENTER to display the Keyword Search menu.

• If the program is currently showing, press ENTER to start
watching it immediately.

4 Select “new search”.
5 If you want to change the category, scroll up to select the
category you want.

• To search using only the keyword, leave the category set
to “All”.
• If you select a category (“HDTV”, for example) then you’ll
only see programs in that category that also match the
keyword.

6 Highlight “enter keyword” then press ENTER.
52
En

PDP_PRO1540HD.book Page 53 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation
The search Episode Options menu

This search is designed to display all programs that start with
a particular letter.

From the Episode Options menu you can select:
• go to Service bar – closes the panel menu and returns to
the Service bar at the top of the screen
• tune to channel / watch now – exits the TV Guide On
Screen™ guide and tunes to the channel
• set recording – goes to the Record Options menu
• set reminder – goes to the Remind Options menu
• cancel – closes the panel menu and returns to the
highlighted program

1 Select “SEARCH” from the Service bar at the top of the
screen.

2 Press
/

to move to the search category bar, then press
to select “ALPHABETICAL”.

English

Alphabetical search

Navigation and search tips
• The / buttons move the highlight between options in the
menu. Use the number buttons to input information.

3 Press ENTER.
4 Select a letter, then press ENTER to display all programs
starting with that letter.

• If a highlighted field has arrows on either side, press / to
cycle through the options.
• Press ENTER on any option to highlight the default
command (e.g., Done) then press ENTER again to execute
and close the menu.
• Select Cancel then press ENTER to close the menu and
return to the previous screen, or press MENU to close the
menu without saving the changes.

5 Highlight a program then press MENU to display the
Episode Options menu.

• If the program is currently showing, press ENTER to start
watching it immediately.

53
En

PDP_PRO1540HD.book Page 54 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation

Scheduling recordings and reminders

2 Highlight a program in the list then press MENU to display
the Schedule Options menu.

From the Schedule area you can review, edit or delete future
recording sessions and reminders.

1 Select “SCHEDULE” from the Service bar at the top of the
screen.

• Highlight a program in the list to see information related
to that program (data appears in the Info Box).

The Schedule Options menu
Programs marked for reminding or to be recorded (referred to
as scheduled ‘events’) are listed. The icon on the right
indicates the status of the event.
•
•

Daily Records the same channel and time every
Monday through Friday (manual recording only)

•

Regularly – Records the same program any day it airs
on the same channel at the same time1

•

Record Suspend – The program is set to record, but is
suspended because of a conflict with another recording or
auto tune reminder. The recording resumes when the
conflict is cleared.

•

Off: The program remains in the SCHEDULE list, but is
not recorded.
Once only reminder

•

Daily Reminds for the same channel and time every
Monday through Friday (manual reminder only)

•

Regularly – Reminds the same program any day it airs
on the same channel at the same time2

•

Weekly recording (every week at the same time/day)

•

Once only recording

Weekly reminder (every week at the same time/day)

•

Remind Suspend – A reminder is set for the program,
but is suspended because of a conflict with another auto
tune reminder or recording. The reminder activates when the
conflict is cleared.

•

Off: The program remains in the SCHEDULE list but the
reminder is not sent.

The program records if it starts any time up to the midway
point of the originally scheduled program. For example, up to
9:15 for a 9:00 to 9:30 program.

The reactivated reminder appears if the program starts any
time up to the midway point of the original schedule. For
example, up to 9:15 for a 9:00 to 9:30 program.

Press MENU with either “SCHEDULE” (in the Service bar) or a
program highlighted to access the Schedule Options menu.
When “SCHEDULE” is highlighted in the service bar:
• go to Service Bar – closes the menu and returns to the
Service bar at the top of the screen
• sort by – select a sort order for the program listings
• new manual recording – select then fill in the necessary
fields to set the recording
Select “schedule recording” to save and exit or select “cancel”
to exit without saving.
• new manual reminder – select and then fill in all the
necessary fields to set the reminder. Select “schedule
reminder” when you’re done to save and exit, or select
“cancel” to exit without saving.
• done – closes the menu and returns to the Service bar at the
top of the screen
• cancel – closes the menu without saving changes and
returns to the Service bar at the top of the screen
When a program is highlighted:
• go to Service Bar – closes the menu and returns to the
Service bar at the top of the screen
• watch now – selected program appears (this option is “tune
to channel” for a future program)
• cancel – closes the menu and returns to the highlighted
program listing
For recording:
• set recording – set the program to record (opens the Record
Options menu)
• delete recording – remove the recording from the schedule
(requires confirmation)
• edit recording – edit the recording settings (opens the
Record Options menu)
For reminder:
• set reminder – set a reminder notice for the program (opens
the Remind Options menu)
• delete reminder – remove the reminder from the schedule
(requires confirmation)
• edit reminder – edit the reminder settings (opens the
Remind Options menu)

PDP_PRO1540HD.book Page 55 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation

Changing setup options

2 Press ENTER to display the current settings and the
options to change them.
English

You can change TV Guide On Screen™ settings from the Setup
menu. Setup options are divided into three categories: System
Settings, Channel Display, and Default Options.

1 Select “SETUP” from the Service bar at the top of the
screen.

3 Select one of the options, then follow the on-screen

2 Press

to select a Setup option.

instructions.
• Yes, everything is correct (displays a helpful information
screen). Press ENTER to quit the TV Guide On Screen™
System.
• Yes, but my channel lineup is incorrect (displays a
screen with alternate channel lineups). Press ENTER to
display the Channel Editor screen.
• No, repeat setup process (displays Screen 1 shown on
page 32).

Changing the Channel Display settings

Adjustment options appear with each highlighted menu
item.
• System Settings – ZIP/postal code, cable setup, etc.
• Channel Display – Channel position, tuning channel,
display on/off, etc.
• Default Options – General, recording and reminder
defaults

From the Channel Display settings you can set/change:
• the display setting to always display (On), never display (Off),
or display only when channel information is available (Auto
Hide)
• the tuned channel number
• the channel position in the channel listing

1 Highlight the “Change Channel Display” item.

Changing the System Settings
The System Settings include your ZIP/postal code and your
cable TV setup.

1 Highlight the “Change System Settings” item.
2 Press ENTER to display the channel editor.

55
En

PDP_PRO1540HD.book Page 56 Wednesday, August 2, 2006 6:01 PM

TV Guide On Screen™ System Operation
3 Press / to highlight a channel then press ENTER to go
to the Grid Options menu.

Changing the Default Options
The menu provides options to change the default settings for
recordings, reminders, and other general settings.

1 Select the “Change Default Options” item.

From the Grid Options menu you can set:
• channel – On (display in channel list), Off (don’t display)
or Auto Hide (hide when no program information is
available)
• service – the type of service that the channel operates
on (cable, etc.)
• tune channel – the channel number that the channel
listing is tuned to
• position – place that the channel appears in the
channel list

4 After making all selections for the channel, highlight

“done” then press ENTER.
• To cancel without saving the changes, select “cancel”.

2 Select a default option category.
A different panel menu appears for each option.
General default options
box size – the initial size of the Info Box (no, small,
large, last used)
• box cycle – the cycle behavior of the Info Box (no only, small
only, large only, no & small, no & large, small & large, all)
• auto guide – Display TV Guide On Screen™ guide
automatically when you turn on the TV
•

Record defaults
• start – when to start a recording (up to 120 minutes earlier
or later than the program start time, or On time)
• end – when to end a recording (up to 120 minutes earlier or
later than the program end time, or On time)
• recorder – selects a recorder to be used for recording.
Remind defaults
• auto tune – automatically tunes to the correct channel
when a reminder becomes due (Yes or No)
• when – set the display time for the reminder (15 minutes
early to 15 minutes late, or On time)

3 When the settings are complete, highlight “done” then

press ENTER.
• To cancel without saving the changes, select “cancel”.

56
En

PDP_PRO1540HD.book Page 57 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings
Adjustments and Settings
For AV source

Sleep Timer

Off

120

Item

Description

STANDARD

For a highly defined image in a normally bright
room
This selection is shared by the external input and
TV input sources.

DYNAMIC

For a very sharp image with maximum contrast
This mode does not allow manual image quality
adjustment.
This selection is shared by the external input and
TV input sources.

MOVIE

For movies
This selection is shared by the external input and
TV input sources.

GAME

Lowers image brightness for easier viewing
This selection is shared by the external input and
TV input sources

PURE

Reflects input signals as faithfully as possible
For example, you may select this option to check
image materials.

USER

Allows you to customize settings as desired
You can set the mode for each input source.

90
(minutes)

• The factory default is “Off”.

NOTE
• To cancel the Sleep Timer, select “Off” by pressing SLEEP.
• Five minutes before the selected time elapses, the remaining
time appears every minute.
You can also use this menu to set the Sleep Timer.

1
2
3
4

Press HOME MENU.
Select “Sleep Timer”. ( /

then ENTER)
then ENTER)

Select the desired time. ( /

Press HOME MENU again to exit the menu.

For PC source
Item

Description

STANDARD

For a highly defined image in a normally bright room

AV Selection

USER

Viewing options depend upon the current environment (e.g.,
room brightness), the type of the current TV program, or the
type of images input from external equipment. To change the
view, follow the directions below.

Allows you to customize settings as desired
You can set the mode for each input source.

5 Press HOME MENU again to exit the menu.
NOTE

1 Press AV SELECTION.
• The current AV Selection mode appears.

2 Press AV SELECTION again before the displayed mode
disappears.
• For AV source, the mode cycles in this order;
STANDARD, DYNAMIC, MOVIE, GAME, PURE and
USER.
• For PC source, the mode toggles between STANDARD
and USER.
You can also use the menu to change the options.

1
2
3
4

English

When the selected time elapses, the Sleep Timer automatically
places the system into standby.
Press SLEEP to select the desired time.
• The timer starts counting.
• Each time you press SLEEP, the selection cycles as below:

(cancel)

• You can also press AV SELECTION on the remote control
unit to change the viewing option.
• Selecting the DYNAMIC viewing setting causes all other
viewing options to become unavailable (grayed out).

Press HOME MENU.
Select “Picture”. ( /

then ENTER)

Select “AV Selection”. ( /

then ENTER)

Select the desired option. ( /

then ENTER)

AV Selection
STANDARD
DYNAMIC
MOVIE
GAME
PURE
USER

57
En

PDP_PRO1540HD.book Page 58 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings
For PC source, the following screen appears:

Basic picture adjustments
Adjust the picture to your preference unless DYNAMIC was
selected. The DYNAMIC setting automatically adjusts the
image.

1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select an item to be adjusted. ( / then ENTER)

Picture
AV Selection
Contrast

STANDARD
40

Brightness

Red

Green

Blue

Picture
Reset
AV Selection

STANDARD

Contrast

Brightness

Color

Tint

Sharpness

NOTE
• To perform advanced picture adjustments, select “Pro
Adjust” in step 3 then press ENTER. For the subsequent
procedures see “Advanced picture adjustments” on page 59.
• To restore the factory defaults for all items, press / to
highlight “Reset” in step 3 then press ENTER. A confirmation
screen appears. Press / to select “Yes” then press
ENTER.

Pro Adjust
Reset

4 Select the desired level. ( / )

Contrast

• When an adjustment screen is displayed, you can also
press / to change the item to be adjusted.

5 Press HOME MENU to exit the menu.
For AV source
Item

button

Contrast

For less contrast

For more contrast

Brightness

For less brightness

For more brightness

Color

For less color intensity

For more color intensity

Tint

Skin tones become
purplish

Skin tones become
greenish

Sharpness

For less sharpness

For more sharpness

For PC source
Item

58
En

button

Contrast

For less contrast

For more contrast

Brightness

For less brightness

For more brightness

Red

For weaker red

For stronger red

Green

For weaker green

For stronger green

Blue

For weaker blue

For stronger blue

PDP_PRO1540HD.book Page 59 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings

Advanced picture adjustments

Using PureCinema
1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select “Pro Adjust”. ( / then ENTER)
4 Select “PureCinema”. ( / then ENTER)
5 Select the desired parameter. ( / then ENTER)
• For the selectable parameters, refer to the table below.
PureCinema

• If you have selected a desired parameter in this step,
skip steps 7 and 8.
• An option is to apply a fine adjustment. To do this, select
“Manual” first and then press and hold ENTER for at
least three (3) seconds. The manual adjustment screen
appears. Continue to step 7.
Color Temp

Automatically detects a film-based source (originally encoded at 24
frames/second), analyzes it, then recreates each still film frame for highdefinition picture quality.
Selections

Using Color Temp
1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select “Pro Adjust”. ( / then ENTER)
4 Select “Color Detail”. ( / then ENTER)
5 Select “Color Temp”. ( / then ENTER)
6 Select the desired parameter. ( / then ENTER)

English

The Plasma Display System provides various advanced
functions for optimizing the picture quality. For details on these
functions, see the following tables.

Adjusts the color temperature, resulting in a better white balance.
Selections

High

White with bluish tone

Off

Deactivates the PureCinema.

Mid-High

Intermediate tone between High and Mid

Standard

Produces smooth and vivid moving
images (film specific) by automatically
detecting recorded image information
when displaying DVD or high-definition
images (e.g., movies) having 24 frames
per second.

Mid

Natural tone

Mid-Low

Intermediate tone between Mid and Low

Low

White with reddish tone

Manual

Color temperature adjusted to your
preference

ADV

Produces smooth and quality moving
images (as shown on theatre screens) by
converting to 72 Hz when displaying DVD
images (e.g., movies) having 24 frames
per second.

NOTE
• “Standard” is unavailable for 480p or 720p@60 Hz or
1080p@24 Hz (HDMI) signals.
• “ADV” is unavailable for 1080p@24 Hz (HDMI) signals.

7 Select an item to be adjusted. ( / then ENTER)
8 Select the desired level. ( / )
Item

button

R High
G High

For weaker red
Fine adjustment for
bright portions

B High
R Low
G Low

Fine adjustment for
dark portions

B Low

button
For stronger red

For weaker green

For stronger green

For weaker blue

For stronger blue

For weaker red

For stronger red

For weaker green

For stronger green

For weaker blue

For stronger blue

• To adjust another item, press RETURN, then repeat
steps 7 and 8.
• Press

to select another item for adjustment.

9 Press HOME MENU again to exit the menu.

59
En

PDP_PRO1540HD.book Page 60 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings

Using CTI
1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select “Pro Adjust”. ( / then ENTER)
4 Select “Color Detail”. ( / then ENTER)
5 Select “CTI”. ( / then ENTER)
6 Select the desired parameter. ( / then ENTER)

Using Color Space
1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select “Pro Adjust”. ( / then ENTER)
4 Select “Color Detail”. ( / then ENTER)
5 Select “Color Space”. ( / then ENTER)

CTI

Color Space

Color Transient Improvement (CTI) provides images with clearer color
contours.

Changes the color reproduction space.

Selections

Off

Deactivates CTI

Activates CTI

Optimized for vivid, vibrant color
reproduction

Standard color reproduction

7 Press HOME MENU again to exit the menu.

Using Color Management
1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select “Pro Adjust”. ( / then ENTER)
4 Select “Color Detail”. ( / then ENTER)
5 Select “Color Management”. ( / then ENTER)
6 Select an item to be adjusted. ( / then ENTER)

Using Intelligent Color
1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select “Pro Adjust”. ( / then ENTER)
4 Select “Color Detail”. ( / then ENTER)
5 Select “Intelligent Color”. ( / then ENTER)

Item

button

Closer to magenta

Closer to yellow

Closer to red

Closer to green

Closer to yellow

Closer to cyan

Closer to green

Closer to blue

Closer to cyan

Closer to magenta

Closer to blue

Closer to red

• To adjust another item, press RETURN then repeat steps
6 and 7.
• Press

6 Select the desired parameter. ( / then ENTER)
Intelligent Color

7 Select the desired level. ( / )

to select another item for adjustment.

8 Press HOME MENU again to exit the menu.

Selections

7 Press HOME MENU again to exit the menu.

Color Management

6 Select the desired parameter. ( / then ENTER)

Intelligent Color (IC) automatically selects the optimum color tones for an
image.
Selections

Off

Deactivates Intelligent Color

Activates Intelligent Color

7 Press HOME MENU again to exit the menu.

PDP_PRO1540HD.book Page 61 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings

• Choose “DNR”, “MPEG NR” or “BNR”.

Using the Dynamic Range Expander (DRE)
functions
1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select “Pro Adjust”. ( / then ENTER)
4 Select “DRE”. ( / then ENTER)
5 Select an item to be adjusted. ( / then ENTER)

6 Select the desired parameter. ( / then ENTER)
DNR
Digital Noise Reduction (DNR) eliminates video noise for clean, crisp
images.
Selections

Off

Deactivates DNR

High

Enhanced DNR

Mid

Standard DNR

Low

Moderate DNR

• Choose “Dynamic Contrast”, “Black Level”, “ACL”,
“Gamma” or “Intelligent DRE”.

6 Select the desired parameter. ( / then ENTER)
Dynamic Contrast
Dynamic Contrast (DC) emphasizes image contrast so that the difference
between bright and dark areas become more distinct.
Selections

MPEG NR
MPEG NR, video noise reduction for MPEG-encoded content, eliminates
mosquito noise (tiny irregularities in the image) from video when a DVD is
played. The result is a noise-free image.
Selections

Off

Deactivates Dynamic Contrast

High

Enhanced Dynamic Contrast

Mid

Standard Dynamic Contrast

Low

Moderate Dynamic Contrast

Black Level

Deactivates MPEG NR

Black Level (BL) emphasizes the dark portions of images so that the
difference between bright and dark areas become more distinct.

High

Enhanced MPEG NR

Selections

Mid

Standard MPEG NR

Low

Moderate MPEG NR

Off

English

Eliminating noise from images
1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select “Pro Adjust”. ( / then ENTER)
4 Select “NR”. ( / then ENTER)
5 Select an item to be adjusted. ( / then ENTER)

Off

Deactivates Black Level

Activates Black Level

ACL
BNR
Block Noise Reduction (BNR) helps reduce mosquito noise appearing in
high-definition images.
Selections

Off

Deactivates BNR

Activates BNR

7 Press HOME MENU again to exit the menu.

Automatic Contrast Limiter (ACL) automatically selects the optimum
contrast for an image.
Selections

Off

Deactivates ACL

Activates ACL

Gamma
Gamma adjusts the image gradation characteristics.
Selections

Selects gamma characteristics 1

Selects gamma characteristics 2

Selects gamma characteristics 3

Intelligent DRE
Intelligent Dynamic Range Expander (DRE) optimizes the image quality.
Selections

Off

Deactivates Intelligent DRE

Activates Intelligent DRE

7 Press HOME MENU again to exit the menu.

61
En

PDP_PRO1540HD.book Page 62 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings
Using the 3DYC and I-P Mode
1 Press HOME MENU.
2 Select “Picture”. ( / then ENTER)
3 Select “Pro Adjust”. ( / then ENTER)
4 Select “Others”. ( / then ENTER)
5 Select an item to be adjusted. ( / then ENTER)

Sound adjustments
Adjust the sound to your preference. See page 57.

1
2
3
4

Press HOME MENU.
Select “Sound”. ( /

then ENTER)

Select an item to be adjusted. ( / )
Select the desired level. ( / )

• Choose “3DYC” or “I-P Mode”.
Sound STANDARD

6 Select the desired parameter. ( / then ENTER)
3DYC
3DYC optimizes characteristics for separating brightness signals and
color signals. This works for both video and still images.

Treble

Bass

Balance

Reset

Selections

Off

Deactivates 3DYC

High

Enhanced 3DYC

Mid

Standard 3DYC

Low

Moderate 3DYC

Off

button

I-P Mode optimizes conversion from interlace signals to progressive
signals. This works for both video and still images.

Treble

For weaker treble

For stronger treble

Bass

For weaker bass

For stronger bass

Selections

Balance

Decreases audio from the
right speaker

Decreases audio from the
left speaker

Optimum for video images

Standard setting

Optimum for still images

7 Press HOME MENU again to exit the menu.
NOTE
• In I-P Mode, the individual parameters are unavailable for
480p and 720p@60 Hz signals.

Off

Front Surround

Item

I-P Mode

FOCUS

5 Press HOME MENU again to exit the menu.
NOTE
• To restore all factory defaults, press / to select “Reset” in
step 3 then press ENTER. A confirmation screen appears.
Press / to select “Yes” then press ENTER.

PDP_PRO1540HD.book Page 63 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings
FOCUS
1
2
3
4

Press HOME MENU.
Select “Sound”. ( /

then ENTER)

Select “FOCUS”. ( / )
Select the desired parameter. ( / )

Item

Description

Off

Deactivates FOCUS

Activates FOCUS

Power Control
Power Control provides convenient power saving options.

Energy Save
There are three Energy Save modes to reduce power
consumption.

1
2
3
4

Press HOME MENU.
Select “Power Control”. ( /
Select “Energy Save”. ( /

then ENTER)
then ENTER)

Select “Save1”, “Save2” or “Picture Off”. ( /
ENTER)

then

Item

Description

Standard

Maximum picture brightness; may increase glass
panel buzzing

Front Surround

Save1

Front Surround provides three-dimensional sound effects and/
or a deep, rich bass.

Slightly reduced power consumption and brightness;
optimal setting for most uses

Save2

Lowest power consumption; slightly decreased
brightness

Picture Off

Deactivates the screen to save power. To restore the
screen display, press any button other than VOL +/–
and MUTING.
This setting is not memorized by the system.

5 Press HOME MENU again to exit the menu.

1
2
3
4

Press HOME MENU.
Select “Sound”. ( /

then ENTER)

Select “Front Surround”. ( / )
Select the desired parameter. ( / )

Item

Description

Off

Deactivates both SRS and TruBass

SRS

Reproduces highly effective three-dimensional sound

TruBass
(factory default)

Provides deep, rich bass using a new technology

TruBass + SRS

Provides both TruBass and SRS effects

English

Focus shifts the sound-source direction (sound image) upward
and produces clear sound contours.

5 Press HOME MENU again to exit the menu.
NOTE
• When the signal is coming from a PC, use the Home menu
to set this option.

No Signal off (AV mode only)
5 Press HOME MENU again to exit the menu.
NOTE
•
•

(WOW) FOCUS is on and TruBass + SRS is selected
for Front Surround
trademark of SRS Labs, Inc.

• WOW technology is incorporated under license from SRS
Labs, Inc.

The system automatically enters Standby if no signal is
received for 15 minutes.

1
2
3
4

Press HOME MENU.
Select “Power Control”. ( /
Select “No Signal off”. ( /
Select “Enable”. ( /

Item

then ENTER)
then ENTER)

then ENTER)

Description

Disable
Does not place the system into Standby
(factory default)
Enable

Places the system into Standby if no signal is
received for 15 minutes

5 Press HOME MENU again to exit the menu.
NOTE
• Five minutes before the system is placed into Standby, a
message appears as each minute counts down.
• The system may not enter Standby if the TV program signal
has a high video noise level.

63
En

PDP_PRO1540HD.book Page 64 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings

No Operation off (AV mode only)
The system automatically enters Standby when no operation is
performed for three hours.

1
2
3
4

Press HOME MENU.
Select “Power Control”. ( /

then ENTER)
then ENTER)

Select “No Operation off”. ( /
Select “Enable”. ( /

Item

then ENTER)

Description

Disable
Does not place the system into Standby
(factory default)
Enable

Places the system into Standby if no operation is
performed for three hours

5 Press HOME MENU again to exit the menu.

• Five minutes before the system is placed into Standby, a
message appears as each minute counts down.

Power Management (PC mode only)
The system automatically enters Standby when no signal is
received from the PC.
Press HOME MENU.
Select “Power Control”. ( /

then ENTER)

Select “Power Management”. ( /
Select “Mode1” or “Mode2”. ( /

Item

This function adjusts an image’s horizontal/vertical position on
the Plasma Display.

1
2
3
4

Press HOME MENU.
Select “Option”. ( /
Select “Position”. ( /

then ENTER)
then ENTER)

Select “H/V Position Adjust”. ( /

then ENTER)

Position
H/V Position Adjust
Reset

5 Adjust the vertical position ( / ) or horizontal position
( / ).

NOTE

1
2
3
4

Image position adjustment
(AV mode only)

6 Press HOME MENU again to exit the menu.
NOTE
• To restore the factory defaults, press / to select “Reset”
in step 4 then press ENTER. A confirmation screen appears.
Press / to select “Yes” then press ENTER.
• Adjustments are stored separately for each input source.
• Depending on the displayed video, the image position may
not change even after adjustment.

then ENTER)
then ENTER)

Description

Off
No power management
(factory default)
Mode1

• Places the system into Standby when no signal is
received from the PC for eight minutes
• Although the PC is accessed and a signal is
received again, the system stays off.
• Press STANDBY/ON on the Plasma Display or TV
on the remote control to turn the panel On

Mode2

• Places the system into Standby when no signal is
received for eight seconds
• Access the PC (a signal is received again), the
system turns On
• Press STANDBY/ON on the Plasma Display or TV
on the remote control to turn the panel On.

Automatic image position and clock
(Hertz) adjustments (PC mode only)
Use Auto Setup to automatically adjust image positions and
clock speeds when coming from a PC.

1 Press HOME MENU.
2 Select “Option”. ( / then ENTER)
3 Select “Auto Setup”. ( / then ENTER)
Option
Auto Setup
Manual Setup

• Auto Setup begins.

4 Press HOME MENU again to exit the menu.
5 Press HOME MENU again to exit the menu.

NOTE
• When Auto Setup is finished, “Auto Setup completed.”
appears.
• Although “Auto Setup completed.” appears, Auto Setup may
have failed, depending on conditions.
• Auto Setup may fail with a PC image composed of similar
patterns or a monochrome picture. If Auto Setup fails,
change the PC image and try again.
• The PC and the Plasma Display must be turned On before
starting Auto Setup.

64
En

PDP_PRO1540HD.book Page 65 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings

Usually you can easily adjust the positions and clock of images
using Auto Setup. Use Manual Setup to optimize the positions
and clock of images when necessary.

1
2
3
4

Press HOME MENU.
Select “Option”. ( /

then ENTER)

Select “Manual Setup”. ( /

In single-screen mode, press SCREEN SIZE to change the size
of the screen. The Video signal determines the available screen
size options.
• The selectable screen sizes differ depending on the type of
input signal.

AV mode

then ENTER)

Select an item to be adjusted. ( /

Selecting a screen size manually
English

Manual image position and clock
adjustments (PC mode only)

then ENTER)

Manual Setup
H/V Position Adjust
Clock

Phase

Item

Description

4:3

For 4:3 “standard” pictures (side bar appears on each
side)

FULL

For 16:9 squeezed pictures

ZOOM

For 16:9 letterbox pictures (bars may appear on the top
and bottom on some programs)

CINEMA

For 14:9 letterbox pictures (bars may appear on the top
and bottom on some programs)

WIDE

In this mode pictures are stretched to fill the screen,
side to side

Reset

5 Perform adjustment. ( / or / )
• With “Clock” or “Phase” selected, you can change the
parameter using / .

6 Press HOME MENU again to exit the menu.
NOTE
• To restore all factory defaults, press / to select “Reset” in
step 4 then press ENTER. A confirmation screen appears.
Press / to select “Yes” then press ENTER.

NOTE
• Avoid displaying signals that do not completely fill the
screen. This may cause temporary or permanent image
retention depending on the frequency and duration.

PC mode except for XGA signals
Item

Description

4:3

Fills the screen without altering the input signal aspect
ratio

FULL

Full 16:9 screen display

Dot by Dot

Matches input signal to the same number of screen
pixels

PC mode for XGA signals
(Ex. 1024 × 768 input with PRO-1140HD/PRO-1540HD)
Item

Description

4:3

Matches input signal to the same number of screen
pixels
Optimized for 1024 × 768 display

FULL1

Full 16:9 screen display
Optimized for 1024 × 768 display

FULL2

For wide signal display
Use when displaying 1360 × 768 signal resolution

NOTE
• In 2-screen mode, press SCREEN SIZE to change the size of
the left screen.
• For the PRO-940HD the number of panel pixels is different.
Signal processing and actual viewing conditions vary
slightly.

65
En

PDP_PRO1540HD.book Page 66 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings
• When watching a High Definition TV broadcast, press
SCREEN SIZE to cycle through FULL, ZOOM, WIDE, and 4:3.
• High Definition TV broadcasting with WIDE selected may
hide some of the screen image. If this is the case, select
FULL.
• Some HD broadcasts may display 4:3 content with side
masks. Extended viewing with the sides masked can cause
uneven wear. After viewing 4:3 content, try watching a
program in full screen motion video.

AV mode

Selecting a screen size automatically
The Plasma Display automatically selects an appropriate
screen size when video signals are received from a connected
HDMI device (see page 69). To activate this function, use the
following procedure.

1
2
3
4

Press HOME MENU.
Select “Option”. ( /

then ENTER)

Select “Auto Size”. ( /
Select “On”. ( /

then ENTER)

Auto Size

4:3

Off
On

WIDE

FULL

Item

Description

Off
(factory default)

Deactivates the Auto Size function

Activates the Auto Size function

5 Press HOME MENU again to exit the menu.
CINEMA

ZOOM

PC mode except for XGA signals

NOTE
• Manually select an appropriate screen size if an image does
not automatically switch to the correct screen format.
• When the video signal contains no aspect ratio information,
automatic screen sizing is unavailable.

Selecting a screen size for 4:3 aspect ratio
signals

4:3

With the Auto Size function activated, choose whether the
Plasma Display should choose the 4:3 mode or WIDE mode
when 4:3 aspect ratio signals are received.

Dot by
Dot

FULL

PC mode for XGA signals

1
2
3
4

Press HOME MENU.
Select “Option”. ( /
Select “4:3 Mode”. ( /

then ENTER)
then ENTER)

Select “WIDE” or “4:3”. ( /

then ENTER)

4:3 Mode

4:3

WIDE
4:3

FULL2

FULL1

NOTE
• The selectable screen sizes may differ depending on the
conditions.

Item

Description

WIDE
(factory default)

Wide image without side masks

4:3

4:3 aspect ratio with side masks

WIDE

4:3

5 Press HOME MENU again to exit the menu.
66
En

PDP_PRO1540HD.book Page 67 Wednesday, August 2, 2006 6:01 PM

Adjustments and Settings

With the 4:3 screen size selected for the AV mode, you can
change the brightness of the gray vertical bars (side masks)
that appear on the sides of the screen.

1
2
3
4

Press HOME MENU.
Select “Option”. ( /

then ENTER)

Select “Side Mask”. ( /

then ENTER)

Select the desired parameter. ( /

Language setting
To change the language being used for on-screen displays
(such as menus in French or Spanish instead of English),
follow the instructions below.

1
2
3
4

Press HOME MENU.
Select “Option”. ( /

English

Changing the brightness on both sides
of the screen (Side Mask)

then ENTER)

Select “Language”. ( /

then ENTER)

Select a language. ( / )

then ENTER)
Language

Item

Description
Menu

English

Fixed
Always sets the same brightness for the gray side
(factory default) masks
Auto

Adjusts the brightness of the gray side masks
according to the brightness of images

5 Press HOME MENU again to exit the menu.
5 Press HOME MENU again to exit the menu.
NOTE
• Displaying pictures in 4:3 screen mode for an extended
period may cause an after-image. View another program at
full screen afterwards to avoid this issue.

67
En

PDP_PRO1540HD.book Page 68 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
Using External Equipment
About External Equipment
You can connect many types of devices to your Plasma Display
System. Some examples are a DVD player, VCR, PC, game
console, or camcorder.
To view images coming from external equipment, select the
input source using the INPUT buttons on the remote control or
the INPUT button on the Plasma Display.

CAUTION
• To protect equipment, always unplug the Plasma Display
from the power outlet before adding to a DVD player, VCR,
PC, game console, camcorder, or other device.

Displaying a DVD image
To watch a DVD image, press INPUT 2 on the remote control
unit or press INPUT on the Plasma Display to select INPUT2.

NOTE
• Refer to your DVD player instruction manual for the signal
type.
• The INPUT 2 terminals are checked whether they are
connected in the following order; 1) Component Video, 2) SVideo, 3) Video.
Use the desired connection for viewing.
• Connect external equipment to only terminals that are to be
actually used.

NOTE
• Refer to the device’s operating instructions (DVD player, PC,
etc.) before connecting the equipment.

Watching a VCR image
Connecting a VCR

Watching a DVD image

Use the INPUT 1 terminals when connecting a VCR or other
audio/visual equipment.

Connecting a DVD player

Plasma Display (rear view)

Use the INPUT 2 terminals when connecting a DVD player or
other audio/visual equipment.

S-Video cable

Plasma Display (rear view)

(sold separately)

AV cable
(sold separately)

S-Video cable
(sold separately)

AV cable
(sold separately)

Component Video cable
(sold separately)

VCR

Displaying a VCR image
DVD player

To watch a VCR image, press INPUT 1 on the remote control
unit or press INPUT on the Plasma Display to select INPUT1.

NOTE
• INPUT 1 checks for S-Video connections first then for Video.
Use the desired connection for viewing.

68
En

PDP_PRO1540HD.book Page 69 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

12
To specify the digital video signal type:

Using HDMI Input

Input signal correlation table

1
2
3
4
5

Press HOME MENU.
Select “Option”. ( /

Select “HDMI Input”. ( /
Select “Video”. ( /

then ENTER)

Select the type of digital video signals. ( / then ENTER)
• If you select “Auto”, the panel automatically attempts to
identify the type of digital video signal.

Item

19201080i@59.94/60 Hz

then ENTER)

Description

720480p@59.94/60 Hz

Auto
Automatically identifies input digital video signals
(factory default)

1280720p@59.94/60 Hz

Color-1

Digital Component Video signals (4:2:2) locked

720(1440)480i@59.94/60 Hz

Color-2

Digital Component Video signals (4:4:4) locked

19201080p@24 Hz

Color-3

Digital RGB signals locked

For audio, the panel supports the following:
• Linear PCM (STEREO 2ch)
• Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

6 Press HOME MENU again to exit the menu.

NOTE
• PC signals are not supported.
• Images are sometimes slow to appear with some external
devices.

English

The INPUT 5 and INPUT 6 terminals are HDMI terminals for
digital video and audio signals. To use the HDMI terminal,
specify the types of video and audio signals being sent from the
connected equipment. For signal types refer to the device’s
operating manual.
Before bringing up the menu, press INPUT 5 (or INPUT 6) on
the remote control or press INPUT on the Plasma Display to
select INPUT 5 (or INPUT 6).

NOTE
• If you select a parameter other than “Auto”, verify that the
setting results in the appropriate colors.
• If no image appears, specify another digital video signal type.
• Refer to the external device’s operating instructions for
digital video signal types.

To specify the type of audio signals:

Connecting HDMI equipment
Plasma Display (rear view)
Viewed from the bottom
of the Plasma Display

HDMI cable with
the HDMI mark
(sold separately)
Audio cable (sold
separately)
Use when inputting
analog audio signals.

1
2
3
4
5

Press HOME MENU.
Select “Option”. ( /

then ENTER)

Select “HDMI Input”. ( /
Select “Audio”. ( /

then ENTER)

Select the type of audio signals. ( / then ENTER)
• If you select “Auto”, the panel automatically attempts to
identify the type of audio signal.

Item

Description

Auto
Automatically identifies input audio signals
(factory default)
Digital

Accepts digital audio signals

Analog

Accepts analog audio signals

6 Press HOME MENU again to exit the menu.
NOTE

HDMI equipment

• If there is no sound, specify another audio signal type.
• Refer to the external device’s operating instructions for
audio signal types.
• Depending on the equipment to be connected, you may also
need to connect analog audio cables.

69
En

PDP_PRO1540HD.book Page 70 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

Using a game console or watching
camcorder images
Connecting a game console or camcorder
Use the INPUT 4 terminals to connect a game console,
camcorder, or other audio/visual equipment.

Plasma Display (left side view)
Component Video cable
(sold separately)

AV cable
(sold separately)

NOTE
• INPUT 4 checks for Component Video connections first then
for Video.
Use the desired connection for viewing.
• Only connect external equipment to terminals that are to be
actually used.

Displaying an image of the game console or
camcorder
To watch an image coming from the game console or
camcorder, press INPUT 4 on the remote control or press
INPUT on the Plasma Display to select INPUT4.

Recording digital TV programs using a
VCR
To record, connect recording equipment such as a VCR to the
panel’s MONITOR OUT terminals (rear of the Plasma Display).
You can also record digital TV programs more easily by using
the TV Guide On Screen™ system. Connect the supplied GLINK cable to the G-LINK terminal on the rear of the Plasma
Display. Position the G-LINK cable’s wand so that its light
emitting section faces the remote control sensor on the
recording equipment. For more information, see page 73.

Avoiding unwanted feedback
You can prevent unwanted feedback from affecting the image
quality. To block the signal from the output terminal causing
interference, follow the steps below.

Camcorder/Game Console

1
2
3
4

Press HOME MENU.
Select “Option”. ( /

then ENTER)

Select “Monitor Out”. ( /

then ENTER)

Select “INPUT1 Prohibit”, “INPUT2 Prohibit”, “INPUT3
Prohibit”, “INPUT4 Prohibit”, “INPUT 5 Prohibit” or
“INPUT 6 Prohibit”. ( / then ENTER)

5 Press HOME MENU again to exit the menu.

70
En

PDP_PRO1540HD.book Page 71 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

Connecting other audio equipment

Plasma Display (rear view)

The panel’s digital audio output terminal (optical) can output
Dolby Digital signals. Using an optical digital cable, connect
an AV receiver to the optical terminal on the rear of the Plasma
Display. This allows high-quality audio, such as during a digital
TV broadcast, to play.
If your AV receiver does not have a digital audio input terminal
(optical), connect MONITOR OUT (AUDIO) on the rear of the
Plasma Display to the audio input terminals on the AV receiver.
This method may cause sound delays between the speakers and
AUDIO. Try muting the speakers on the Plasma Display, however,
you may still experience a delay between audio and video.

Ferrite core

Viewed from the bottom
of the Plasma Display

English

Connecting a recorder

NOTE
G-LINK cable (supplied)

• When using the digital audio output terminal (optical), set
according to the AV receiver’s requirements. For more
information, refer to the AV receiver’s operating instructions.

Connecting an AV receiver

AV cable
(sold separately)

Plasma Display (rear view)

VCR
Viewed from the bottom
of the Plasma Display

NOTE
• About the MONITOR OUT terminals
The MONITOR OUT terminals cannot output the following
signals:
•Video signals input from the COMPONENT VIDEO terminal
•Video signals from a PC
•Digital video and audio signals from the HDMI terminals
• When watching images from a VCR connected to the panel’s
MONITOR OUT, select an input source (e.g., TV channel
reception) on the VCR other than an external input source.
Selecting an external input source may cause distorted
images or noise.
• Place the VCR in Standby when selecting TV programs to
record using the TV Guide On Screen™ system.
• Using MONITOR OUT may cause delays between the
speaker and AUDIO. If this delay occurs, try muting the
speakers on the Plasma Display. However, you may still
experience some delay between audio and video.
• The MONITOR OUT terminals cannot output any signals for
networked audio or video.
• If degraded picture quality is observed while viewing copyprotected VOD movies connect the Plasma Display directly
to other TV sets. Do not connect through a VCR.

Optical digital cable
(sold separately)

This connection is
not required when
connecting an AV
amp equipped
with surround
sound to a
subwoofer.

AV cable
(sold separately)

Subwoofer

AV receiver

NOTE
• For details, refer to the audio device’s operating instructions.
• The audio accompanying the images shown on the display is
always output to the SUBWOOFER OUTPUT terminal.
• When signals are input from the HDMI terminals, no digital
or analog signals are output from the DIGITAL OUT terminal.
• Input signals from the Home Media Gallery may cause audio
delays between the speakers and OPTICAL. Try muting the
speakers on the Plasma Display; however, you may still
experience delays between audio and video.

71
En

PDP_PRO1540HD.book Page 72 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

Switching the optical audio signal type
Set up for the DIGITAL AUDIO output terminal (OPTICAL),
according to your AV receiver’s operating instructions.

1
2
3
4

Press HOME MENU.
Select “Option”. ( /

then ENTER)

Select “Digital Audio Out”. ( /

then ENTER)

Select “Dolby Digital” or “PCM”. ( /

Item

When connected to a PC, the input signal type is automatically
identified. If the image from the PC does not come in clearly,
you may need to use Auto Setup. See page 64.
To watch an image coming from the PC, press PC on the
remote control or press INPUT on the Plasma Display to select
“PC”.

then ENTER)

Description

Dolby Digital
Dolby Digital: outputs in the Dolby Digital format
(factory default) PCM: outputs in the PCM format
PCM

Displaying an image from a PC

Always outputs in the PCM format regardless of the
types of signals

NOTE
• The PC terminals are for PC use only. Do not connect audio/
visual equipment to PC terminals.

Signal names for 15-pin mini D-sub connector

5 Press HOME MENU again to exit the menu.

4
10

3
13

1
6

Watching an image from a computer
(front view)

Connecting a personal computer
Use the PC terminals to connect a personal computer (PC).

NOTE
• The PC input terminals are DDC2B-compatible.
• Ability to use Plug & Play depends on the computer.

Plasma Display (rear view)
Viewed from the bottom
of the Plasma Display

RGB cable
(sold
separately)
AV cable with a mini plug
(sold separately)
(for PC audio connection)

Personal Computer

72
En

Pin No.

Signal name

Not connected

GND (ground)

+5V

GND (ground)

Not connected

SDA

SCL

NOTE
• An Apple® Macintosh® adaptor may be required for use with
some Macintosh computers.

PDP_PRO1540HD.book Page 73 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

Computer compatibility chart
Frequency

720 × 400

70 Hz

640 × 480

60 Hz

Attaching the ferrite core
To help prevent noise, attach the supplied ferrite core to the
connector end of the G-LINK cable as shown.
G-LINK cable

English

Resolution

Ferrite core

72 Hz
75 Hz
800 × 600

56 Hz
60 Hz
72 Hz
75 Hz

1024 × 768

60 Hz
70 Hz
75 Hz

1360 x 768

60 Hz

Pull the cable slightly to
take up any slack A.

G-LINK™ connection

To record with a VCR through the TV Guide On Screen™
system, connect the VCR to the panel using the G-LINK cable.

NOTE
• In order to use a VCR with the TV Guide On Screen™ system,
confirm the factors listed below. See “TV Guide On Screen™
System Setup” on page 32.
• The G-LINK cable’s wand must be positioned so that its light
emitting section faces the VCR’s remote control sensor.
• The VCR is in Standby when selecting TV programs to record
using the TV Guide On Screen™ system.
• Avoid the cable loops when making the connection.

As close as possible

CAUTION
• Regarding the G-LINK cable, attach the supplied ferrite core.
If you do not do this, this Plasma Display will not conform to
mandatory FCC standards.

When connecting the VCR
Plasma Display (rear view)

Ferrite core

AV cable (sold
separately)

Viewed from the bottom
of the Plasma Display

G-LINK cable (supplied)

G-LINK cable’s wand

VCR

Point to the remote
control sensor

73
En

PDP_PRO1540HD.book Page 74 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

Connecting control cables

Plasma Display (rear view)

Connect control cables between the Plasma Display and other
PIONEER equipment having the
logo. These control cables
carry commands from a Pioneer device through its remote
control to the remote control sensor on the Plasma Display.
After the CONTROL IN terminals have been connected, the
remote control sensors on the device does not accept
commands from the remote control. Point the remote control
at the remote control sensor on the Plasma Display to operate
the device.

NOTE
• Make sure that the power is turned Off when connecting
cables.
• Connect all components before plugging cables into the
panel.

CONTROL
IN

OUT

About SR+
The CONTROL OUT terminal on the rear of the Plasma Display
supports SR+. This terminal supports linked operations with a
PIONEER AV receiver. SR+ includes functions such as input
switch linkage operation and DSP surround display. For more
information, see the Pioneer AV receiver’s operating
instructions regarding SR+ support.

CONTROL
IN

OUT

NOTE
• When connecting control cables, use the SR+ cable.
• When connecting one or more Pioneer devices, directly
connect the Plasma Display and an SR+ supported Pioneer
amplifier. Do not daisychain other equipment between the
Pioneer units.
• When operating devices using SR+, volume on the Plasma
Display is lowered temporarily.

CONTROL
IN

OUT

When SR+ is not used:
Use mono sound control cables with
mini plugs, no resistance (sold
separately)
When SR+ is used:
Use the SR+ cable (sold as an option).

74
En

PDP_PRO1540HD.book Page 75 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

Enjoying the Home Media Gallery

Installing Windows Media Connect
Before installing Windows Media Connect, make sure that
Windows XP SP2 and other required software are installed.
See Microsoft Website for details regarding minimum system
requirements and installation procedures.
1

Download the most recent version of Windows Media
Player
This can be downloaded either directly from the Microsoft
Website, or using the Windows Update Installer.

Download the most recent Windows Media Connect
software
This can be downloaded either directly from the Microsoft
Website, or using the Windows Update Installer.

NOTE
• Content may not play or display properly depending on the
conditions of use.
• Sources for this panel include media servers that support
DLNA (Digital Living Network Alliance) and Windows Media
Connect (WMC) running on the LAN network, or SD Card,
MS, MMC, xD Picture and CF that comply with the Mass
Storage File System through a USB interface.
• Supported formats and contents are subject to change. Visit
the Pioneer website for updated information:
http://www.pioneerelectronics.com
• The Home Media Gallery functions as a WMDRM10-ND
(Microsoft Windows Media DRM for networked devices).
Content can only be navigated from the media servers that
support WMDRM10-ND.
• The system may not be able to display content from
incompatible memory cards.
• You cannot use the Home Media Gallery until dimmed
elements on the menu screen turn white.

English

With Home Media Gallery, you can enjoy digital content such
as movies, music and photo files. These files can be saved on
one or more media servers connected by a home network
(LAN) or from content stored on USB devices. After connecting
via an Ethernet hub to a media server with network software*,
you can navigate through the server’s digital content using the
Plasma Display. For USB interface, the Plasma Display
supports Mass Storage Class devices.
* Referred to as a “media server” that contains digital content
such as movies, music and photo files. PCs that have preinstalled media server software and recorders with a media
server function are considered the media server. Use PCs that
have a Windows Media Connect (WMC) server or DLNA
compliant server for the Home Media Gallery function.
Take a Windows Media Connect (WMC) server for example:
Microsoft Media Server is freeware and works with any music
juke-box type software, although is optimized for Windows
Media Player.

Digital Audio Output terminal (Optical)

NOTE
• When using the optical output terminal for networked audio or
video:
If the Plasma Display and audio system are in the same room,
you may experience an audio delay between the plasma
speakers and the audio system. Try muting the speakers on
the Plasma Display to correct this delay. However, this action
may cause delays between audio and video.

Supported file formats
The table below shows supported file formats that can be
played back or displayed on the Plasma Display. These formats
are applicable to both network and USB sources. However,
media server content protected by digital rights management,
such as WMDRM10 (Digital Rights Management for Windows
Media 10), may not play on the Plasma Display.
Type of files

Format

Movie

MPEG PS (mpg, mpeg, mpe, m2p), MPEG-2 TS/TTS,
WMV (asf, wmv), MPEG4 (mp4)

Music

MP3 (mp3), LPCM, WAV (wav), WMA (asf, wma)

Photo

JPEG (jpg, jpeg), BMP (bmp), PNG (png), TIFF (tif, tiff),
GIF (gif)

• Some formats may not be supported depending on the
server type or version used.
• Even with the format included in the above table, some
functions may not operate properly depending on the
content.
• Even with the format included in the above table, some files
may not be played properly through a USB device.

75
En

PDP_PRO1540HD.book Page 76 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
Confirming the IP Address

Making network connections
To connect to a network, set up the Home Media Gallery
through the panel’s menu. Connect to a home network (LAN)
via an Ethernet hub or cable directly to a media server.

1 Press HOME MENU.

NOTE
• Although the Home Media Gallery supports 10BASE-T, it is
better to use 100BASE-TX for improved display quality and
speed.

Connecting via an Ethernet hub

2 Select “Home Media Gallery” ( /
3 Select “Setup” ( /

then ENTER).

4 Select “Network Setup” ( /

then ENTER).

5 Select “Automatically acquire IP” ( / / / then

If you already operate one or more media servers on a local
area network (LAN), connect the Plasma Display to the
Ethernet (LAN) hub using a standard (“straight-through”)
Ethernet (LAN) cable. See the diagram below.
Media Server 2

After making the network connection, follow the instructions
below to confirm the panel’s IP Address before accessing the
network. (The setup is effective for “Auto” only. To perform the
procedure, DHCP on your server or router must be valid.)

Plasma Display
(rear view)

Ethernet Hub
(Router with hub function)
Viewed from the
bottom of the
Plasma Display
Straight-through
Cable

Media Server 1

ENTER).
• The screen turns from “Select” mode to “Input” mode.

6 Select “Yes” ( / then ENTER).
• The IP Address is automatically assigned.
• The Home Media Gallery supports Auto IP and DHCP
(Dynamic Host Configuration Protocol). If the system
failed to acquire the IP Address or if you want to obtain
different addresses, select “No” then enter “IP Address”
and “Subnet mask”. Use the 0 to 9 and / / /
buttons to enter an address, then press ENTER. You do
not need to enter “Default Gateway” and “DNS Server”.

7 Select “OK” ( / then ENTER).
• The “Reset” dialog appears on screen.

8 Select “OK” and press ENTER.
• The home network module restarts.
• A message “Setting up Home Media Gallery. Please wait
until initialized.” appears on screen.
• When the initialization is finished, setting values
become effective and the top menu of the Home Media
Gallery returns.

NOTE
Connecting directly to a Media Server
To run a PC as a media server, connect the Plasma Display
directly to the PC using a twisted (“cross-over”) Ethernet (LAN)
cable. See the diagram below.

Plasma Display
(rear view)
Viewed from the
bottom of the
Plasma Display

Cross-over Cable

• For information on DHCP, refer to network device’s
operating instructions.
• You may need to contact your service provider or network
administrator when manually entering an IP Address.
• Some media servers block or are programmed to block
access to client servers. When connecting the Plasma
Display, check the media server for client server access
rights.

Connecting a USB device
You can also enjoy content stored on memory cards by
connecting a USB device to the Plasma Display. When you
insert a USB memory or multi-card reader into the USB port,
the root directory or the Device List screen appears. In addition,
you can connect your digital camera directly to the Plasma
Display using a USB connector cable.

1 Press HOME MENU.
2 Select “Home Media Gallery” ( /
3 Select “USB” ( /
Media Server 1

76
En

then ENTER).

then ENTER).
• The Device List is displayed on screen with the selected
device highlighted if you have not checked in the “Single
Server/USB” box after selecting “Setup” and then “Auto
Connection Setup”. If you have checked in the box, the
list is skipped.

PDP_PRO1540HD.book Page 77 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
4 Select the desired device ( /

5 Press ENTER to navigate to a folder or play a file/content.
• To return to the previous screen, press RETURN.

6 Press HOME MENU again to exit the Home Media Gallery.
NOTE
• If the Home Media Gallery is launched and the “Single
Server/USB” box is checked after selecting “Setup” and then
“Auto Connection Setup”, the system displays the root
directory immediately after inserting a USB device. In this
case, you can start from step 5. When a multi-card reader is
inserted, the Device List appears with the selected device
highlighted. In this case, you can start from step 4.
Plasma Display

USB flash memory

Removing a USB device
To remove a USB device, exit the Home Media Gallery first and
then disconnect the device.

NOTE

English

then ENTER).
• You can select a device only when the Device List is
displayed.

• Be sure to exit the Home Media Gallery screen before
removing the USB device. If you remove the USB device
while the Home Media Gallery screen is displayed, data
inside the memory may be damaged.
• Do not insert or remove the USB device immediately after the
system is switched On or Off. This action may cause data
inside the memory to be damaged.
• PIONEER is not liable for any loss or damage to the data
inside the USB memory.

Starting the Home Media Gallery function
1 Press HOME MENU.
2 Select “Home Media Gallery” ( / then ENTER).
3 Select “Media Navigator”, “USB”, “My Playlist” or “Setup”
( / then ENTER).
• To return to the previous screen, press RETURN.

4 Press HOME MENU again to exit the Home Media Gallery.
Home Media Gallery

Digital Camera with USB
Mass Storage Class

Media Navigator

Server
XXXXXX

USB
My Playlist
Setup

Flash media via USB adapter (Multi-card Reader )

Readable memory cards
This system reads FAT12, FAT16, FAT32, or VFAT Memory
Cards.

Readable data files
Movie, music and photo files can also be played with the
exception of Digital Rights Management for Windows Media
10 (DRM) protected files.

NOTE
• A single USB device can be connected at a time and no USB
hub connected.
• This system may not be able to display modified or edited
content from a PC or other equipment.
• This system supports the USB Mass Storage Class.
• Some digital cameras may require a setup procedure for
Mass Storage Class data transfer. The setup is done on the
camera. See the operating instructions supplied with the
digital camera.

Navigating the files and folders
By selecting Media Navigator, the previously selected server
menu is automatically displayed on the screen by default (page
90). When only one server is found, the system automatically
connects the server. You can also use the Tool Menu to switch
to another server or manually select a server from the Server
List. The display is automatically changed to a server list if
there are no previously navigated servers.

1 Press HOME MENU.
2 Select “Home Media Gallery” ( /

then ENTER).

3 Select “Media Navigator” ( /

then ENTER).
• A server menu appears. The file/folder configuration
may vary depending on the server selected.
• After selecting a category, folder or container and
navigating on subsequent screens, you can find a file
and start the appropriate Player depending on the
selected file.

4 Select the desired folder to navigate or file/content to play
( /

then ENTER).

5 Press ENTER to display a subsequent screen.
• Subsequent screen(s) appears.
• To return to the previous screen, press RETURN.

6 Press HOME MENU again to exit the Home Media Gallery.
77
En

PDP_PRO1540HD.book Page 78 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
Selectable screen display
Menu display options are: “List”, “Thumbnail” or “Thumbnail
List”. Press D then select “Change view” from the Tool Menu to
choose from the screen display options.
List screen

Function

Slide Show Setup

Used to set up a slideshow on the Photo
Player

Server List/Media
Navigator/USB/My
Playlist/Playlist List
(Movie/Music/Photo)/
Folder Contents List/
Contents List/Photo
Player

Add to My
Playlist*1

Adds the selected files
to My Playlist

Media Navigator/Folder
Contents List/Contents
List/Movie Player/Music
Player/Photo Player

Select Server

Moves to the Server List Media Navigator/Folder
screen
Contents List/Contents
List

Stop Music*2

Stops playback of a
music file

Change Name

Used to change content Playlist List (Movie/
names in My Playlist
Music/Photo)

Change view

Switches the screen
display to List,
Thumbnail, or
Thumbnail List

Time Search

Starts playback at the
Movie Player/Music
preset time on the Movie Player
or Music Player screen

Slow Playback

Plays back in the slow
mode on the Movie or
Music screen

BGM Setup

Used to set up the slide- Photo Player
show BGM on the Photo
Player

All Photos
XXXX
Title
XXXX

XXXX
XXXX

Album
XXXX
Date
2006/11/19
Server
XXXXXX

XXXX
XXXX
XXXX
XXXX
XXXX
1/27
1

D Tool

Thumbnail screen
All Photos
All Photos
XXXX

Add to My Playlist

Til
X
All
X
Da
2
Se
X

Change view

List

Sort

Thumbnail

Thunbnail List
XXXX

Slide Show Settings
Detailed Display

XXXX

Select Searver

XXXX

Stop Music

XXXX

Title
XXXX
Album
XXXX
Date
2006/11/19
Server
XXXXXX
1/27

1/27

D Tool

Screen on which Tool
Menu is available

Menu items

Thumbnail List screen

Media Navigator/ Playlist
List (Movie/ Music/
Photo)/Folder Contents
List/Contents List/Music
Player/Photo Player

All Photos
XXXX
Title
XXXX
Album
XXXX
Date
2006/11/19
Server
XXXXXX

XXXX
XXXX
XXXX

Folder Contents List/
Contents List

1/27

D Tool

Using the Tool Menu
Press D on the remote control to access the pop-up Tool Menu.
Various play and display modes can be selected from the Tool
Menu. The selectable menu items differ depending on the
submenu (see the table below).

78
En

Movie Player/Music
Player

Menu items

Function

Screen on which Tool
Menu is available

Move

Moves the order of
content in My Playlist

Update to Latest
Information

Updates the server
connection status

Server List (connected/
not connected)

Delete from My
Playlist*1

Deletes the selected
Contents List (Playlist)
content from My Playlist

Delete Server

Deletes the server(s)
that are dimmed on the
list

Server List (server not
connected)

*1 When a file is selected
*2 While music is played

USB Devices List

Moves to the USB
Devices List screen

Folder Contents List
(USB)/Contents List
(USB)

Consecutive
Playback*1

Continuously plays video Media Navigator/Folder
content starting from the Contents List/Contents
selected item
List

Detailed Display*1 Displays the detailed
information on the
selected content

Media Navigator/Folder
Contents List/Contents
List

Sort

Sorts items in Folder or
Contents List

Media Navigator/Folder
Contents List/Contents
List

Searches the desired
items in Folder or
Contents List by word

Folder Contents List/
Contents List

Contents List (Playlist)

PDP_PRO1540HD.book Page 79 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

12
4 Select a Playlist list from “Movie Playlist”, “Music Playlist”

Media Navigator

or “Photo Playlist” (

then ENTER).

5 Select the desired content ( / or

/ then ENTER).
• The menu can be displayed as a “List”, “Thumbnail” or
“Thumbnail List” screen. Press D then select “Change
view” from the Tool Menu ( / then ENTER).

Screen Components

English

While navigating through the folders a media server provides,
you can select the desired file to start the corresponding player
by pressing ENTER.

6 Press ENTER to play or display.
1

• To return to the previous screen, press RETURN.

7 Press HOME MENU again to exit the Home Media Gallery.

Media Navigator

Movie
Title
Movie

Music

Server
XXXXXX

User Files

Enjoying movie files

Photos

5
1/4
1

D Tool

1
2
3
4
5
6
7

Thumbnail of the file selected (if obtained)
Name of the server currently selected
Current menu level
Item being selected (highlighted in yellow)
File number/total number of files
Number of servers connected
Key guide

Screen Components
1 2

NOTE

XXXX
2006/11/30 00:00:59

XXXX

• The Media Navigator is not launched depending on the
option selected in “Auto Connection Setup” (page 90). The
screen displays after selecting a server in the server list.

USB
Like navigating through the media servers, you can select the
desired file contained in the device selected on the USB
Devices List screen to start the corresponding player by
pressing ENTER. You can also select the menu displayed on
either “List”, “Thumbnail” or “Thumbnail List” screen. Press D
and select “Change view” from the Tool Menu.

NOTE
• The USB Devices List screen may not be displayed
depending on the option selected in “Auto Connection
Setup”. “Single Server/USB” is selected for “Auto
Connection Setup” by default. You don't need to select a
device in the USB Devices List when you use a single
directory device (USB memory).

My Playlist
Each category (Movie, Music and Photo) has five different
Playlists in which you can register up to 100 files each. The My
Playlist option can contain sound and image files selected in
the “Media Navigator”. To edit a Playlist, use the Tool Menu
(page 78).

Playback

A A-B

1
2
3
4
5
6
7
8
9
10
11
12

B Repeat

L R A-B

00 : 00 : 45
C Random

RDM

10
12

D Tool

9 11

Movie icon
Title (Category or Folder name)
Date
Album name
Play time
Play status
Key guide
Progress bar
Audio mode icon
A-B repeat mode icon
Repeat mode icon
Random mode icon (appears when the mode is valid)

1 Press HOME MENU.
2 Select “Home Media Gallery” ( /
3 Select “My Playlist” ( /

then ENTER).

then ENTER).
79
En

PDP_PRO1540HD.book Page 80 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
Movie Player key guide
ENTER:
:

Pauses while playback or plays back while in PAUSE
Fast reverse during playback or when in PAUSE. Each
press toggles the reverse speed between x 2, x 4, x 8,
x 20, x 50, and x 100 or the slow mode speed between
x 1/2, x 1/4, x 1/8, and x 1/16. When the beginning of the
content is reached, it pauses.

Fast forward while playback or PAUSE. Each press
toggles the forward speed between x 2, x 4, x 8, x 20,
x 50, and x 100 or the slow mode speed between x 1/16,
x 1/8, x 1/4, and x 1/2. When the end of the content is
reached, it pauses.

Skips 15 seconds backward and plays back or pauses
while in PAUSE

Skips 15 seconds forward and plays back or pauses
while in PAUSE

Play modes
Time Search

(Tool Menu)

Plays back the selected content
from the time preset on the Movie
Player

Slow
Playback

(Tool Menu)

Plays back the content in slow
mode on the Movie or Music
Player

Add to My
Playlist

(Tool Menu)

Adds the selected content to My
Playlist List (Not available while
movie content in the Playlist is
played back.)

Stop Movie
Player

 (STOP),
RETURN

Stops the Movie Player

Fast Forward/
Fast Reverse

See the key guide table

/

Forward/
Reverse
(15 sec.)

See the key guide table

 (PLAY):

Plays back the content

 (PAUSE):

Pauses the playback

 (STOP):

Stops the Player and returns to the previous screen
(List/Thumbnail/Thumbnail List)

Play

ENTER,
 (PLAY)

See the key guide table

 (FF):

Same as
mode)

(only fast forward function while in the slow

A-B Repeat
Mode

A (BLUE)

See the key guide table

 (RWD):

Same as
mode)

(only fast reverse function while in the slow

Repeat Mode

B (RED)

See the key guide table
See the key guide table

Sets A-B repeat mode. Sets the desired point A to start
and B to end during playback. To cancel the mode,
press A (BLUE) on the remote control.

Random
Mode

C (GREEN)

A (BLUE):

(Tool Menu)

D (YELLOW)

See the key guide table

B (RED):

Every press toggles the repeat mode between “No
Repeat” and “Repeat Once” or between “No Repeat”,
“Repeat Once” and “Repeat All” while in Playlist

NOTE
• Some functions may not be supported depending on the
server type or version used.
• During playback, an error may arise in time-related
information depending on the content or server software.
• Some functions may not be supported depending on the
content.

C (GREEN):

Available only in Playlist or “Consecutive Playback”
mode. Every press toggles the random mode between
“Random Off” and “Random On”.

D (YELLOW):

Switches the Tool Menu display on and off. Even if the
Tool Menu is displayed while content is played back, a
movie is kept playing but the time counter and progress
bar do not function.

INFO:

Displays the Player status at the bottom of the screen
while a movie is played back. Another press of the key
displays a key guide, as well. Pressing the key once
more cancels all the information display.

1 In playback mode or PAUSE, press D then select “Time

Every press of the key toggles the audio mode between
“L + R”, “L” and “R”

2 Select “Hour” and/or “Minute” for “Input Time” ( /

MTS:
RETURN:

Same function as STOP

VOL+, VOL-:

Adjusts the sound volume

MUTING:

Mutes the sound

HOME MENU:

Quit the Home Media Gallery and returns to the last
entry screen. Resumes the content selected again on
the Home Media Gallery.

Time Search
Search” from the Tool Menu ( / then ENTER).
• A “Time Search” dialog screen appears.
then

ENTER).
• Enter the desired time using buttons 0 to 9.
Time Search
Input Time

1 H
OK

Min

Cancel

3 Press ENTER after the entry is complete.
4 Select “OK” ( /

then ENTER).
• The movie begins playing from the time you set.
• To cancel the Time Search, select “Cancel” and press
ENTER.

80
En

PDP_PRO1540HD.book Page 81 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
5 Press HOME MENU to exit the Home Media Gallery.

12
Fast Forward/Fast Reverse

1 While playing content, press and hold
or press and hold

• This function may not be supported depending on the
content or server software.
• An error may arise in time-related information depending on
the content or server software.

Slow Playback

1 In playback mode or PAUSE, press D then select “Slow
Playback” from the Tool Menu.

Forward/Reverse (15 sec.)

1 While playing content, press and hold

or
to jump
backward or forward in 15-second increments.

A-B Repeat Mode

1 While playing content, press A where you want repeat to
start.

2 Press ENTER.
• Slow playback begins.
• You can change the playback speed by pressing /
while in the slow mode.
• To discontinue slow playback, press ENTER or PLAY.
The system returns to the normal playback mode.

3 Press HOME MENU to exit the Home Media Gallery.
NOTE
• This function may not be supported depending on the
content.

Add to My Playlist

1 While navigating or playing, select the file to be added to
My Playlist (

for Fast Reverse

for Fast Forward.

English

NOTE

then ENTER).

2 Press D then select “Add to My Playlist” from the Tool
Menu ( / then ENTER).
• A “Playlist Selection” dialog screen appears.

3 Select a Playlist ( /

then ENTER).
• A check mark is provided beside the selected Playlist.
• When you select a different Playlist and press ENTER,
the mark jumps to the new Playlist from the previously
selected one.
Playlist Selection
Select a Playlist to register
Playlist1
Playlist2
Playlist3
Playlist4
Playlist5

20
0
0
0
0

Cancel

4 Select “OK” ( /

then ENTER).
• The file is added to the selected Playlist.
• To cancel the operation, select “Cancel” then press
ENTER.

5 Press HOME MENU to exit the Home Media Gallery.

2 Press A again where you want repeat to end.
• The Player status appears on the screen and the A-B
mode icon changes.
• The selected movie scenes are repeatedly played back.
• To return to normal mode, press A again while in the
A-B repeat mode.

3 Press HOME MENU to exit the Home Media Gallery.
NOTE
• The A-B repeat function is only available during playback in
normal mode.

Repeat Mode

1 While playing content in the Media Navigator or USB
device, press B to select “Repeat Once”.
• The title being played is repeated.

2 Press B again to cancel the repeat mode (“Repeat Off” is
selected).
• After playing the currently selected title, the Player
stops.

3 Press HOME MENU to exit the Home Media Gallery.
NOTE
• When playing content in the Playlist, you can select from
“Repeat Off”, “Repeat All” (plays all items in the Playlist
repeatedly) or “Repeat Once” (plays the content being
watched repeatedly).

Random Mode

1 While playing content in the Playlist, press C to select
“Random On”.
• Random Repeat playback starts.

2 Press C again to cancel the random mode (“Random Off”
is selected).

3 Press HOME MENU to exit the Home Media Gallery.
NOTE
• The Random Repeat mode is only available for content in the
Playlist, or in “Consecutive Playback” mode.

81
En

PDP_PRO1540HD.book Page 82 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
Music Player key guide

Enjoying music files
You can display the menu as a “List”, “Thumbnail” or
“Thumbnail List” screen. Press D then select an option under
“Change view” on the Tool Menu. You can also navigate
through the subsequent or preceding menu levels in the server
or USB device by pressing / / / /ENTER.
When you select music content from the server menu on the
Media Navigator screen, the Music Player automatically
launches. Select a category, folder, or device to access the
submenu containing the required file or content. The Music
Player screen appears when you select a music file from My
Playlist, just like selecting a file in the server.

NOTE

Moves up a cursor to a title above

Moves down a cursor to a title below

ENTER:

Fast reverse during playback or when in PAUSE. Each
press toggles the reverse speed between x 2, x 4, x 8,
x 20, x 50, and x 100. When the beginning of the content
is reached, it pauses.

Fast forward during playback or when in PAUSE. Each
press toggles the forward speed between x 2, x 4, x 8,
x 20, x 50, and x 100. When the end of the content is
reached, it pauses.

• The Music Player only displays a “List” screen.

Screen Components
1

RETURN:

Returns to the previous screen (List/Thumbnail/
Thumbnail List). Content being played does not stop.

 (PLAY):

Plays back the selected content. Pauses while in
playback and plays while in PAUSE.

 (PAUSE):

Pauses the playback

 (STOP):

Stops the Player and does not return to the previous
screen (Selecting the “Stop Music” from the Tool Menu
also stops the Player.)

 (FF):

Same as

 (RWD):

Same as

A (BLUE):

Sets A-B repeat mode. Sets the desired point A to start
and B to end during playback. To cancel the mode,
press A (BLUE) on the remote control.

B (RED):

Every press toggles the repeat mode between “No
Repeat”, “Repeat Once” and “Repeat All”

C (GREEN):

Every press toggles the random mode between
“Random Off” and “Random On”

D (YELLOW):

Displays the Tool Menu. Even if the Tool Menu is
displayed while content is played back, music is kept
playing but the time counter and progress bar do not
function.

All Music
XXXX
XXXX
XXXX

XXXX
XXXX

XXXX
XXXX
XXXX

XXXX

Playback

A A-B

1
2
3
4
5
6
7
8
9
10
11
12
13

XXXX

00:01:00
Other

XXXX
2/20

A-B

00 : 00 : 14
B Repeat

Plays back the selected music content. Pauses the
music content being played if it is highlighted in the
Playlist screen or plays the selected music content if
different content is highlighted by pressing / .

C Random

RDM

D Tool

Title (Category or Folder name)
Jacket image (Music icon)
Music status icon
Contents list
Number of items
Detailed display
Play status
Time counter
Key guide
Progress bar
A-B repeat mode icon
Repeat mode icon
Random mode icon

11 12

PAGE+, PAGE-: Available only when there are one or more pages in the
content. Change the pages back and forth.
VOL+, VOL-:

Adjusts the sound volume

MUTING:

Mutes the sound

HOME MENU:

Quit the Home Media Gallery and returns to the last
entry screen

NOTE
• Files may not be played back properly depending on the
content.

82
En

PDP_PRO1540HD.book Page 83 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

12
4 Press HOME MENU to exit the Home Media Gallery.

Play modes
(Tool Menu)

Adds the selected content to My
Playlist List (Not available while
music content is played back.)

Time Search

(Tool Menu)

Plays back the selected content
from the time preset on the Music
Player

Stop Music

(Tool Menu),
 (STOP)

Stops the Music Player

/ ,
/

See the key guide table

3 Press HOME MENU to exit the Home Media Gallery.

See the key guide table

Enjoying photo files

Fast Forward/
Fast Reverse
Moves Up/Down
a cursor

Random Mode

1 While playing content in the Playlist, press C to select
“Random On”.
• Random Repeat playback starts.

English

Add to My Playlist

2 Press C again to cancel the random mode (“Random Off”
is selected).

Play

ENTER,
 (PLAY)

See the key guide table

A-B Repeat
Mode

A (BLUE)

See the key guide table

Repeat Mode

B (RED)

See the key guide table

Random
Mode

C (GREEN)

See the key guide table

(Tool Menu)

D (YELLOW)

See the key guide table

• Setup procedures for the above play modes are the same as
for the Movie Player.
• Refer to page 78 for the color button D (Tool Menu).

NOTE
• Some functions may not be supported depending on the
server type or version used.

You can display the menu as a “List”, “Thumbnail” or
“Thumbnail List” screen. Press D then select an option under
“Change view” on the Tool Menu. You can also navigate
through the subsequent or preceding menu levels in the server
or USB device by pressing
/ / / /ENTER.
When you select photo content from the server menu on the
Media Navigator screen, the Photo Player automatically
launches. The selected content is displayed in full screen by
pressing ENTER. Select a category, folder or device to access
the submenu containing the required file or content.
Pressing ENTER again allows a slideshow to begin. After a
slideshow launches, pressing ENTER toggles between “PLAY”
and “PAUSE”. Instead of pressing ENTER twice, you can press
PLAY to start the slideshow immediately.
The Photo Player screen appears when you select a photo file
from My Playlist, just like selecting a file in the server.

Screen Components
1 2

A-B Repeat Mode

1 While playing content, press A where you want repeat to

3
XXXX
2006/11/30

XXXX

start.

2 Press A again where you want repeat to end.
• The Player status appears on the screen and the A-B
repeat mode icon changes.
• The selected part of the title is repeatedly played back.
• To return to normal mode, press A again while in the A-B
repeat mode.

Playback

B Repeat

3 Press HOME MENU to exit the Home Media Gallery.
NOTE
• The A-B repeat function is only available during playback in
normal mode.

Repeat Mode

1 While playing content in the Media Navigator, USB device
or Playlist, press B to select “Repeat All”.
• All titles in the folder or Playlist are played repeatedly.

2 Press B again to cancel the repeat mode (“Repeat Once”
is selected).
• The title being played is repeated.

1
2
3
4
5
6
7
8
9
10

RDM

6 / 27

C Random

9
10

D Tool

Photo icon
Title (Category or Folder name)
Album name
Date
Number of items
Play status
Key guide
Progress bar
Repeat mode icon
Random mode icon

3 Press B once more to cancel the repeat mode (“Repeat
Off” is selected).
• After playing the currently selected title, the Player
stops.
83
En

PDP_PRO1540HD.book Page 84 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
Photo Player key guide

Play modes

ENTER:

Starts displaying a photo or playing a slideshow. Pauses
while playback or plays back while in PAUSE.

BGM Setup

(Tool Menu)

Sets up BGM

Stops the Player and returns to the previous screen
(List/Thumbnail/Thumbnail List)

Slide Show
Setup

(Tool Menu)

RETURN:

Allows various slideshow setups
on the Photo player

Add to My
Playlist

(Tool Menu)

Adds the selected content to My
Playlist List (Not available while
photo content is displayed.)

Stop Photo
Player

 (STOP),
RETURN

Stops the Photo Player

Displays the previous image content

Display the next image content

 (PLAY):

Plays a slideshow

 (PAUSE):

Pauses the slideshow

) See the key guide table

Stops the Player and returns to the previous screen
(List/Thumbnail/Thumbnail List)

Move File Forward/
Backward

( / /

 (STOP):

Slideshow

Rotates the image 90º clockwise. Each press toggles
the rotation angle by 90º between 90º, 180º, 270º and 0º.

ENTER,
 (PLAY)

See the key guide table

 (FF):

Rotate

A (BLUE),

See the key guide table

 (RWD):

Rotates the image 90º counter-clockwise. Each press
toggles the rotation angle by 90º between 270º, 180º,
90º, and 0º.

A (BLUE):

Rotates the image 90º clockwise. Each press toggles
the rotation angle by 90º between 90º, 180º, 270º and 0º.

B (RED):

Every press toggles the repeat mode between “No
Repeat” and “Repeat All”

C (GREEN):

Every press toggles the random mode between
“Random Off” and “Random On”

D (YELLOW):

Displays the Tool Menu. If the Tool Menu is displayed
while a slideshow is played, the slideshow and BGM are
paused.

INFO:

Displays the Player status at the bottom of the screen
while image content is played. Another press of the key
displays a key guide, as well. No Player information is
displayed when an image is shown in full screen (no
slideshow has been started). Other information may
display. Pressing the key once more cancels all the
information display.

VOL+, VOL-:

Adjusts the sound volume

MUTING:

Mutes the sound

HOME:

Replaced by the Home Menu key. Quit the Home Media
Gallery and returns to the last entry screen.

/
Repeat Mode

B (RED)

See the key guide table

Random
Mode

C (GREEN)

See the key guide table

(Tool Menu)

D (YELLOW) See the key guide table

• Setup procedures for the above play modes are the same as
for the Movie Player.
• Refer to page 78 for the color button D (Tool Menu).

NOTE
• Some functions may not be supported depending on the
server type or version used.
• In rare cases, the image on the screen may appear jagged
when photo content is selected directly from a USB device.
If this is the case, the problem may be solved by viewing the
photo content through the network after having transferred
it to the server PC.
• Even with the supported format, files may not be played
properly depending on the content.

Setting up the slideshow
You can enjoy a slideshow with music in the background. To
activate this feature, you must register music content in My
Playlist List beforehand (see “My Playlist” on page 79 and
“Setting up BGM” on page 85).

1
2
3
4

Press HOME MENU.
then ENTER).

Select “Home Media Gallery” (

Select “Media Navigator” (

then ENTER).

Press D.
• A pop-up screen of the Tool Menu appears.

5 Select “Slide Show Setup” ( / then ENTER).
6 Select the desired setup item ( / then ENTER).
7 Enter the setting in the “Effect” or “Interval” box ( /
then ENTER).
• Repeat steps 6 and 7 to enter another setup.
Slide Show Setup
Effect

Auto

Interval

3 seconds

84
En

Cancel

PDP_PRO1540HD.book Page 85 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

12
6 Select “BGM ON”, “BGM ON (Random)” or “BGM OFF”

8 Select “OK” ( /

then ENTER).
• The slideshow setup finishes.

from the BGM status box (

then ENTER).

• After setting the “Interval” time, it may take longer than the
preset time until the next image is obtained.

Rotating the image

Starting the slideshow

2 Select “Home Media Gallery” ( / then ENTER).
3 Select photo content in the Media Navigator, USB device

1 Press HOME MENU.
2 Select “Home Media Gallery” ( / then ENTER).
3 Select photo content in the Media Navigator, USB device
or My Playlist ( / / / then ENTER).
• The photo content is displayed in full screen.

4 Press ENTER or (Play) to start a slideshow.
• The slideshow starts and photo images in the folder
automatically display one by one. See “Setting up the
slideshow” (page 84) for setting up the interval time.
• To display a key guide, press INFO.

5 Press ENTER or  (Pause) to stop the slideshow.
• The Photo Player goes into “PAUSE”.

6 Press ENTER again to resume the slideshow.
• To cancel the slideshow and stop the Photo Player,
press RETURN or  (Stop) during the playback. The
previous screen returns.

NOTE
• When you press / / / , / while photo content
is displayed, the Photo Player goes into “PAUSE”.

English

7 Select “OK” ( /

NOTE

1 Press HOME MENU.

or My Playlist ( / / / then ENTER).
• The photo content is displayed in full screen.
• To stop the slideshow, press ENTER again.

4 Press ENTER or (Play) to start a slideshow.
• The slideshow starts and photo images in the folder
automatically display one by one.
• To display a key guide, press INFO.

5 While using Photo Player, press A to rotate a photo.
• The displayed image rotates by one quarter clockwise.
Each time A is pressed, the image rotates; 90º, 180º,
270º and “Rotate Off”.
• The Photo Player goes into “PAUSE” (the slideshow is in
Stop mode).

6 Press ENTER again to resume the slideshow.
• The selected rotation mode is only effective for the
image being displayed. The default setting (“Rotate Off”)
returns when you move and display content on a
different screen.

Repeating the slideshow

1 While playing a slideshow, press B to select “Repeat

Setting up BGM

Once”.
• The slideshow being played is repeated.

1 Press HOME MENU.
2 Select “Home Media Gallery” ( / then ENTER).
3 Select photo content in the Media Navigator, USB device
or My Playlist ( / / / then ENTER).
• The Photo Player launches and photo content is
displayed in full screen.

4 Press D then select “BGM Setup” from the Tool Menu ( /
then ENTER).
• A “BGM Setup” dialog screen appears.

2 Press B again to cancel the repeat mode (“Repeat Off” is
selected).
• After playing the currently selected slideshow, the
Player stops.

3 Press HOME MENU to exit the Home Media Gallery.
Playing the slideshow at random

1 While playing a slideshow, press C to select “Random On”.

5 Select a Playlist from the list as BGM ( /

then ENTER).
• A check mark is provided beside the selected Playlist.
• When you select a different Playlist and press ENTER,
the mark jumps to the new Playlist from the previously
selected one.

• Random Repeat playback starts.

2 Press C again to cancel the random mode (“Random Off”
is selected).

3 Press HOME MENU to exit the Home Media Gallery.

BGM Setup
Playlist1
Playlist2
Playlist3
Playlist4
Playlist5

20
0
0
0
0
BGM ON

Cancel

85
En

PDP_PRO1540HD.book Page 86 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
5 Select “Bottom-Up” or “Top-Down” in the “Sort Order” box

Other useful functions

(

then ENTER).

Search
You can search the desired items contained in the Folder or
Contents List by word. Searched results are displayed on the
screen.

XXXX
Sort

Title
XXXX

1 Press HOME MENU.

condition:” ( / then ENTER).
• The software keyboard appears on the screen.

1/24

then
ENTER).
• The sorting starts based on your selection and sort
results are displayed.
• Even while sorting, you can select content to play. To
return to the sort screen, press RETURN during
playback.

NOTE

Set the search condition.

• The “Select a sorting order.” screen can be displayed while
navigating through the music categories.

Title
Contains the following:

Cancel

Adding files to My Playlist

1/24

D Tool

6 Enter the word for search on the software keyboard (

then ENTER).

The Home Media Gallery function provides “My Playlist” - a selfcontained play list that allows you to bookmark your favorite
movie, music and photo files from the network. You can
register, edit, and sort up to 100 files in each Playlist List.

1 Press HOME MENU.

7 Select “OK” on the software keyboard ( /

then ENTER).

• The software keyboard disappears.
• To cancel the search, select “Cancel” then press ENTER.

8 Select “OK” on the “Search” dialog screen ( /

then
ENTER).
• The searching starts based on the word entered and
search results are displayed.
• Even while searching, you can select content to play. To
return to the search screen, press RETURN during
playback.

9 Press RETURN to cancel the search mode.
Sort
You can sort the items contained in the Folder or Contents List.

2 Select “Home Media Gallery” ( /

(

then ENTER).

5 Press D to open the Tool Menu.
• A dialog screen appears.
Playlist Selection
Select a Playlist to register
Playlist1
Playlist2
Playlist3
Playlist4
Playlist5

20
0
0
0
0

2 Select “Home Media Gallery” ( / then ENTER).
3 Select the desired folder and/or content in the Media
then ENTER).

4 Press D then select “Sort” from the Tool Menu ( /
ENTER).
• A “Sort” dialog screen appears.

then

then ENTER).

3 Select “Media Navigator” ( / then ENTER).
4 Select the desired music content to add to “My Playlist”

1 Press HOME MENU.

Navigator (

7 Press RETURN to cancel the sort mode.

XXXX

Cancel

6 Select “OK” on the “Sort” dialog screen ( /

5 Select the “Contains the following” box in “Set the search

Bottom-Up

D Tool

then ENTER).
• A “Search” dialog screen appears.

Album
XXXX
Date
2006/11/30
Play Time
00:00:59
Server
XXXXXX

Sort Order

then ENTER).

4 Press D then select “Search” from the Tool Menu ( /

Title
XXXX

Title

Album
XXXX
Date
2006/11/30
Play Time
00:00:59
Server
XXXXXX

2 Select “Home Media Gallery” ( / then ENTER).
3 Select the desired folder and/or content in the Media
Navigator (

Select a sorting order.

Cancel

6 Press ENTER.
• A check mark is provided in the box at the selected
Playlist List.

7 Press to select “OK”.
8 Press ENTER.
• The selected content is added to the Playlist.

9 Press HOME MENU again to exit the Home Media Gallery.
86
En

PDP_PRO1540HD.book Page 87 Wednesday, August 2, 2006 6:01 PM

Using External Equipment

Setup

complete.
• The screen turns to setup selection mode.
• Repeat steps 2 to 4 to complete the necessary
setup.

Setup
Network Setup
Auto Connection Setup
Default Settings
Software Update

6 Select “OK” ( / / /

Home Media Gallery Version

then ENTER).
• A restart dialog screen appears.

1/5
1

7 Press ENTER again on the dialog screen.
• The setup finishes.
• The system restarts then the Home Media Gallery
screen returns.

1 Press HOME MENU.
2 Select “Home Media Gallery” ( /

then ENTER).

3 Select “Setup” ( / then ENTER).
4 Select “Network Setup”, “Auto Connection Setup”,
“Default Settings”, “Software Update” and “Home Media
Gallery Version” ( / / / then ENTER).
“Network Setup”
When you select “Network Setup” from the “Setup” menu,
a submenu is displayed to select “Auto” or “Manual” for
network connections.
To automatically set:
The following setup is effective for “Auto” only. To perform
the procedure, DHCP on your server or router must be
valid.

1 Select “Automatically acquire IP” then press ENTER.
2 Select “Yes” ( /

5 Press ENTER on the setup item’s box after the entry is

English

The “Setup” is used for “Network Setup”, “Auto Connection
Setup”, “Default Settings”, “Software Update” and “Home
Media Gallery Version”.

Enter the same figures as used in the media server
(PC, etc.) you use. For ***, enter 3-digit figures (0 –
254) that have not been used for network
connections yet.

then ENTER).

3 Select “OK”. ( / / /

then ENTER).
• A restart dialog screen appears.

“Auto Connection Setup”
When you enjoy content on the network, you can select
from the following options: “Last Connected Server” and
“Single Server/USB”. See “Auto Connection Setup” on
page 90.
“Wake on LAN (WOL)” functions to turn the last accessed
server’s power on if the server is WOL-compliant and is in
Standby or sleep mode, then display the Media Navigator
screen. During the WOL is activated, the “Start Server”
dialog screen displays and a message “The server is
starting up.” appears. If the server is not WOL-compliant
or the WOL function fails, the “Start Server” dialog appears
on the “Server List” screen and a message “Failed to start
server.” displays on the dialog screen.
For USB content, the Device List is displayed on the
screen if you have not checked in the “Single Server/USB”
box after selecting “Setup” and then “Auto Connection
Setup”. You can select the desired device and then
content in it. If you have checked in the box, the list is
skipped (default setting) and you can see the folder(s) or
file(s) in the USB device that has a single directory.

4 Press ENTER again on the dialog screen.
• The setup finishes.
• The system restarts then the Home Media Gallery
screen returns.
To manually set:
Before setting up, check your media server for IP Address
and Subnet mask.

1 Select “Automatically acquire IP” then press ENTER.
2 Select “No” ( /

then ENTER).

3 Select the setup item’s box ( / / /

then ENTER).
• The screen turns to entry mode for “IP Address” and
“Subnet mask”.
• No need to enter “Default Gateway” and “DNS
Server”.

4 Enter the figures using buttons 0 to 9.
• Subnet mask (such as 255.255.255.0)
Enter the same figures as you checked.
• IP Address (such as 192.168.201.***)

“Default Settings”
Setups you have entered within the Home Media Gallery
function return to default. When you select “Reset”, a
confirmation screen “To activate the default settings,
restart Home Media Gallery.” will appear. Press ENTER to
reset to default. When you select “Cancel”, the previous
screen displays ( / then ENTER).
“Software Update”
Select “Next” to follow the procedure on the subsequent
screens or “Cancel” to return to the previous screen ( /
then ENTER). When update is completed, a
confirmation message “To activate the updated software,
restart Home Media Gallery.” appears. See“Software
Update” on page 89.
“Home Media Gallery Version”
You can confirm the version and copyright information on
the Home Media Gallery software. Select “OK” to return to
the previous screen (ENTER).

8 Press HOME MENU again to exit the Home Media
Gallery.

87
En

PDP_PRO1540HD.book Page 88 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
Editing files in My Playlist

• Repeat steps 2 and 3 to move another content.

4 Press RETURN.

1 Press HOME MENU.
2 Select “Home Media Gallery” ( /

• A “Playlist” dialog screen appears.

then ENTER).

3 Select “My Playlist” ( / then ENTER).
4 Select “Movie Playlist”, “Music Playlist” or “Photo Playlist”
from the Playlist category ( / then ENTER).
• Five playlists are displayed.
• Press D to open the Tool Menu and select an item on
this screen or next contents list screen ( / then
ENTER).
• Check the appropriate box: “Change Name”, “Move” or
“Delete from My Playlist” ( / / / then ENTER).
“Change Name”

1 Select “Change Name” from the Tool Menu.
• A dialog screen appears.

5 Select “OK” ( /

then ENTER).
• The dialog screen disappears and moving content
finishes.
• To cancel, select “Cancel” then ENTER.

“Delete from My Playlist”

1 Select “Delete from My Playlist” from the Tool Menu.
• A dialog screen appears.

2 Select “OK” ( /

then ENTER).
• The dialog screen disappears and the selected content
is deleted from My Playlist.
• To cancel, select “Cancel” then ENTER.

Playing/displaying files from My Playlist

2 Select “Playlist Name” (

then ENTER).
• The software keyboard appears.

1 Press HOME MENU.

3 Select “OK” on the software keyboard ( / / /

then

ENTER).
• The software keyboard disappears and “Playlist Name”
in the “Change Name” dialog screen returns.

4 Select “OK” when the new name is entered ( /

then
ENTER).
• The editing finishes and “Change Name” dialog screen
disappears.
• The new Playlist displays.

2 Select “Home Media Gallery” ( /

then ENTER).

3 Select “My Playlist” ( / then ENTER).
4 Select the desired Playlist from “Movie Playlist”, “Music
Playlist” or “Photo Playlist”.

5 Select the desired Playlist List ( /

then ENTER).

6 Select the desired content ( / / /

then ENTER).
• The selected content is played or displayed.
• To return to the previous screen, press RETURN.

7 Press HOME MENU again to exit the Home Media Gallery.
Movie Playlist
Soft Keyboard
Playlist Name
Title
Playlist1

20
0

Playlist1

1,2,3...

Delete

a,b,c...

Clear

A,B,C...

Space

@,$,=...

1/5
1

• The on-screen keyboard (“Software Keyboard”) is
displayed only when you select “Search” or “Change
Name”.
“Move”
You can change the listing order of the content registered in
My Playlist.

1 Select “Move” from the Tool Menu.
• The content selected is placed in a yellow box (“Source
Selection” mode).

2 Select the desired content ( /

then ENTER).
• The selected content is highlighted in the yellow box. A
specific icon appears on the left (“Destination Selection
mode”).

3 Press

/ to move the content up or down, then ENTER.
• The highlight in the yellow box disappears and the
specific icon returns to the original one.

88
En

When one or more servers are connected within the network,
you can switch between servers.

1 Press HOME MENU.
2 Select “Home Media Gallery” ( /

Cancel
D Tool

Switching the server

then ENTER).

3 Select “Media Navigator” ( /

then ENTER).
• The previous server is selected.

4 Press D to open the Tool Menu.
5 Choose “Select Server” ( /

then ENTER).
• The Server List is displayed.
• Pressing RETURN changes the screen to the Home
Media Gallery.

6 Select the desired server ( /

then ENTER).
• The screen changes from the selected server to the
Home Media Gallery.

7 Press HOME MENU again to exit the Home Media Gallery.
NOTE
• The Home Media Gallery can memorize previously
connected servers. When the Media Navigator is launched,
available servers are automatically searched and connected.
To switch between connected servers, choose server to
another one, select “Select Server” from the Tool Menu.

PDP_PRO1540HD.book Page 89 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
6 Press ENTER after the following steps are complete:
“Download”, “Write” and “Verify”
• A restart dialog screen appears.

7 Press ENTER after reading a notice on the screen.
• The system is restarted then the Home Media Gallery
screen returns.
• Software update finishes.

Resetting to default

Setup

You can reset the setups you have entered within the Home
Media Gallery function to default (See “Default Settings” on
page 87).

Software Update
To check whether the software needs to be updated or not.
Home Media Gallery must be connected to a USB device.
Connect the USB device and press the Next button.
Current Version: 1.x.xx

1 Press HOME MENU.
2 Select “Setup” ( /

English

• If a previously connected server can not be found or if the
server is in the sleep mode, the server name is dimmed
(grayed out).
• In some cases, you may be able to start a media server if it
supports “Wake On LAN”. Select the server and press ENTER
to have it transmit a “Wake On LAN” command to the
Plasma Display.
• You cannot select a server unless that media server has been
set up.

then ENTER).

3 Select “Default Settings” ( /

then ENTER).

Cancel
1

4 Select “Reset” ( /

then ENTER).
• A restart dialog screen appears.

NOTE

5 Press ENTER on the dialog screen.
• The setup finishes.
• The system restarts then the Home Media Gallery screen
returns.

• On average, it may take 15 minutes or more to complete a
software update.

Other convenient features
Screen saver

During navigation, the screen saver launches automatically
if no activity is sensed within five minutes.
• No screen saver is available while a movie or slideshow is
played.
• Pressing any key cancels screen saver. When canceled
with a USB device being connected, connecting operation
resumes.

NOTE
• Pressing INFO to display the Player status or key guide
before screen saver is activated may cause image retention
to appear. Do not display the Player status and key
guide for an extended period of time while playing a
movie or slideshow.
Software Update

Software update is available on the Pioneer website (http://
www.pioneerelectronics.com). Make sure that you have a
USB flash memory. First download the software according to
the guidelines on the website and perform the following
procedure for update:

1 Press HOME MENU.
2 Select “Home Media Gallery” ( /
3 Select “Setup” ( /

then ENTER).

4 Select “Software Update” ( /

then ENTER).
• A “Software Update” submenu appears.

5 Select “Next” ( /

then ENTER).
• The next screen appears. Complete the procedure
following the guidelines on the screen.
89
En

PDP_PRO1540HD.book Page 90 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
Dialog Screen Message

“Auto Connection Setup”

For extra convenience, you can toggle between the following
features:
“Last Connected
Server”

When you check in the “Last Connected Server”
box, the Plasma Display accesses the last server
using WOL (“Wake On LAN”) first as the Media
Navigator is selected from the Home Media
Gallery. The Media Navigator displays the last
server when WOL succeeds, while a server list is
displayed when WOL fails.
WOL is activated to turn the last accessed server
On if the server is WOL-compliant and is in
Standby or sleep mode.

“Single Server/
USB”

This function is used only when a USB memory
device or a single server is connected. You do not
need this function when a multi-card reader, or two
or more servers are connected.
USB:
• When USB memory is connected, the Devices
List is skipped as long as you have checked in
the “Single Server/USB” box. If not, the list may
be displayed at any time.
Media Navigator (Server):
• When a single server is connected, the Server
List is skipped as long as you have checked in
the “Single Server/USB” box. If not, the list may
be displayed at any time. When the “Last
Connected Server” box is checked, the other
server setup option – “Single Server/USB” –
becomes invalid.

No.

Message

001

Content playback failed No details are available
(001).
for the error

100

A communication error No further details are
occurred (100).
available for the error

101

No response from the
server (101).

102

Disconnected from the Cables are
network (102).
disconnected

103

Invalid response was
received from the
server (103).

Invalid response from
the server

300

This format is not
supported (300).

A file that is not
supported is selected

500

Authorization failed
(500).

Failed to obtain
WMDRM authorization

501

Authorization failed
(501).

Failed to obtain
WMDRM authorization

503

Authorization failed
Failed to obtain
(503). Please check for WMDRM authorization
trouble in routers,
hubs, and other
network devices.

504

Authorization failed
(504). The maximum
allowed number of
devices are connected
to the server.

Failed to obtain
WMDRM

505

Authorization failed
(505). The content
license is off. Please
turn on the license
from the server.

Failed to obtain
WMDRM authorization

Setup
Auto Connection Setup
Last Connected Server
Single Server/USB

Cancel
1

Problem

Timeout period reaches
due to delayed server
response

• The message consists of “Error”, “Warning” and “Information” and is
displayed for 5 seconds.

Displaying pictures in the Home Media Gallery for an
extended period may cause an after-image.

90
En

PDP_PRO1540HD.book Page 91 Wednesday, August 2, 2006 6:01 PM

Using External Equipment
Glossary
Default gateway is a node on a computer network that serves
as an access point to another network. A default gateway (such
as a computer and router) is used to forward all traffic that is
not addressed to a station within the local subnet.

DHCP (Dynamic Host Configuration Protocol) Server
Provides a mechanism to allocate IP addresses to client hosts.
In most cases, a broadband router serves as a DHCP server in
a home network.

DLNA (Digital Living Network Alliance)
The DLNA authorized logo makes it easy for consumers to
recognize products that meet the new standard for home
network PCs and other digital devices, as set down in the DLNA
Guidelines for interoperability. This allows music, video, etc. to
be enjoyed from various devices over a home network. This unit
is compatible with music, photo and video content, and is
based on the DLNA Interoperability Guidelines v1.0. This unit
can be used to playback music, photos and video stored on a
DLNA-compatible server connected through a LAN cable.
Digital Living Network Alliance (DLNA) is dedicated to the
simplified sharing of digital content, such as digital music,
photos and video among networked consumer electronics (CE)
and PCs. By establishing a platform of interoperability based
on open industry standards, DLNA delivers technical design
guidelines that companies can use to develop digital home
products that share content through wired or wireless
networks in the home.

DNS (Domain Name Service) Server
DNS Server is a server that determines the name of networkcomputer within the Internet. The server functions to exchange
IP address to the hostname, hostname to the IP address.

Ethernet
A frame-based computer networking technology for local area
networks (LANs). The Plasma Display supports 100BASE-TX.

MAC (Media Access Control) Address
An address attached to the port of any network device with an
IP address. The MAC address is expressed as
“00:e0:36:01:23:xx” and cannot be changed.

Mass Storage Class devices

English

Default Gateway

The standard provides an interface to a variety of storage
devices, such as USB flash memory and digital cameras.

PlaysForSure
This unit incorporates PlaysForSure. “PlaysForSure” is a new
logo program from Microsoft Corporation. You can check for
the PlaysForSure logo at various online stores. Where you see
the PlaysForSure logo, you can be sure that the digital media
you are purchasing (music, video, pictures) will play on this
unit.

Subnet mask
Used when IP addresses are broken into several parts. It is
expressed as “255.255.255.0”. In most cases, the Subnet mask
is automatically assigned by the DHCP server.

USB (Universal Serial Bus)
USB provides a serial bus standard for connecting devices,
usually to computers such as PCs. The Plasma Display
supports the Mass Storage Class.

Windows Media Connect
Microsoft Windows Media Connect is a new technology to
distribute music, photos and video stored on a PC with
Windows XP installed to a stereo system of TV. Using this
technology you can playback files stored on the PC from
various devices wherever you like in your home.

Windows Media DRM
Windows Media DRM is copyright protection technology
developed by Microsoft Corporation. It enables content
providers to distribute over the Internet music, video and other
digital media content in a protected, encrypted file format.

IP (Internet Protocol) Address
A unique number that devices use in order to identify and
communicate with each other on a network utilizing the
Internet Protocol standard, such as “192.168.1.xxx”. No
duplicate numbers are allowed within the network.

LAN Cable
A cable that has an 8-pin modular plug on each end and is
different from a telephone plug which has 4 pins. A straight
cable is used when connecting the Plasma Display to a home
network via a hub. A cross-over cable is used when connecting
directly to a PC. Use category 5 (CAT-5) LAN cables.

91
En

PDP_PRO1540HD.book Page 92 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features
Useful Remote Control Features
Learning function of the remote control
unit

Presetting manufacturer codes to
control other devices

You can operate the connected AV products (AV Receiver,
Cable Box, SAT tuner, VCR, DVD, DVD recorder, LD) using the
remote control’s learning function. The remote control can
memorize other remote control’s codes.

Presetting manufacturer codes
1 Slide the Mode switch to match the type of device to be

2 cm to 5 cm (0.8 inches to 2.0 inches)

preset.

2 Press EDIT/LEARN and 1 at the same time.
• The LED flashes.

3 Press 0 – 9 to enter the manufacturer code. See page 94.
• Preset mode is finished when the LED blinks Off.

Library Search
Remote control
(Supplied accessory)

Remote control of
AV product

Using the learning function
1 Slide the Mode switch to match the type of device to be
learned.

2 Press EDIT/LEARN and 2 at the same time.
• The LED flashes.

3 Press a button to be learned.
• The LED lights up.
• For the functions that can be learned, see pages 99 to
102.
• When the device’s remote is memorized, the LED
flashes.

4 Press EDIT/LEARN again to exit the Learn mode.

In the event that the device code for a particular target unit is
unknown, cycle through the available codes for that type of
device. Sample the functions from each code in order to find
the code that properly operates the target device.

1 Slide the Mode switch to match the type of device to be
preset.

2 Press EDIT/LEARN and 3 at the same time.
• The LED indicator flashes and the remote control unit
enters the Library Search programming mode.

3 Press either SOURCE POWER, PLAY, 1 or CH+ to sample
the selected code.

4 If the code is missing, press / to advance to the next
code or return to the previous code and repeat step 3.

5 Press ENTER when the code that properly operates the
target device is found.
• All the available buttons for the selected mode are
programmed to the remote control. The remote control
unit returns to normal operation (LED lights for one
second to confirm addition).

NOTE
• To exit the Learn mode before it is complete, press EDIT/
LEARN again.
• If the Mode switch selection is changed when EDIT/LEARN
and 2 are pressed (the LED is flashing), the Learn session is
canceled.
• If the Mode switch selection is changed when a button to be
learned is pressed after EDIT/LEARN and 2 have been
pressed (the LED lights up), the Learn session is not
canceled and the selected mode and button remain
effective.
• If no operation is performed for more than one minute after
having pressed EDIT/LEARN and 2 (the LED is flashing), the
Learn session is canceled.
• If a button to be learned is pressed after having pressed
EDIT/LEARN and 2 (the LED is lit), the Learn session is
canceled in 30 seconds and the LED restarts blinking again.
• Code transmission finishes in approximately two seconds.
Do not interrupt it halfway. Wait until the LED flashes again.
• When using any of the receiver buttons (a, INPUT, or
VOL +/–), the learned manufacturer code remains the same
regardless of the Mode switch position or even if the switch
is shifted to a different position.

92
En

Delete Learning
You can delete a learned code by either overwriting it with a
new code on the same button or performing the procedure
below.

1 Press EDIT/LEARN and 2 at the same time.
• The LED indicator flashes and the remote control unit
enters the Learning mode.

2 Press and hold TV a for more than two seconds.
• The remote control unit starts deleting all learned codes
in the selected mode (marked by a lit LED).
• When completed, the LED blinks Off and the remote
control unit returns to normal operation.

PDP_PRO1540HD.book Page 93 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features

Manufacturing Reset
1 Press EDIT/LEARN and TV a at the same time. The Mode
switch setting is ignored.
• The LED indicator flashes and the remote control unit
enters the Manufacturing Reset mode.

English

All learned and preset codes can be returned to the factory
defaults regardless of the mode.

2 Press D (yellow) to reset the remote control.
• The manufacturing reset is complete. The LED flashes
for one second then the remote control unit returns to
normal operation.

NOTE
• To exit the Edit mode before it is complete, press EDIT/
LEARN again.
• If the Mode switch selection is changed when in the Edit
mode, the Edit session is canceled.
• If no operation is performed within one minute, the Edit
session is canceled.
• When you enter an unlisted code, the LED flashes
repeatedly.
• If the tables on pages 94 to 98 do not include your device’s
manufacturer or the remote control does not work, use the
Learn mode.
• The initial mode is “PIONEER”.
• When using any of the receiver buttons (a, INPUT, or
VOL +/–) to cancel the Learn mode, follow the procedure
with the Mode switch set to “TV”. You cannot cancel the
mode otherwise.

93
En

PDP_PRO1540HD.book Page 94 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features
Programming codes
CABLE
Brand

Codes

Brand

ABC

0003 0008 0014 0011

General Instrument

0014 0011

Panasonic

0000 0008 0107 0021

Sony

1006 1506 1606

0017

Global

1327

Panther

0637

Sprucer

0021

Americast

0899

GoldStar

0144

Paragon

0000

Starcom

0003 0014

Amino

1602 1822

Hamlin

0009 0273

Philips

1305 0317

Supercable

0276

Bell & Howell

0014

Hitachi

0014 0011 0154

Pioneer

1877 0877 0144 0533

Supermax

0883

Bell South

0899

Birmingham Cable Communications 0276

Codes

Brand

i3 Micro

1602

Jerrold

0476 0810 0276 0003

Pulsar

0012 0014 0011

Codes

Brand

Codes

0023 0260 1021

Thomson

1256

0000

Tocom

0012

PVP Stereo Visual Matrix 0003

Torx

0003

British Telecom

0003

Clearmaster

0883

KNC

0008

Quasar

0000

Toshiba

0000

ClearMax

0883

0144

RadioShack

0883

Trans PX

0276

Cleartron

1327

Memorex

0000

RCA

1256 0021

Tristar

0883

Coolmax

0883

Motorola

1376 0476 0810 0276

Regal

0279 0273

0003

Daeryung

1877 0877 0477 0008

1187 1254 0014 1106

Rembrandt

0011

United Cable

0003

Digeo

1187

0883

Runco

0000

0883

Multitech

Digi

0637

MultiVision

0012

Samsung

0000 0144

Viewmaster

0883

Director

0476

Myrio

1602 1822

Scientific Atlanta

1877 0877 0477 0008

ViewmaxPro

1544

Dumont

0637

NTL

0003

0017

Vision

0883

Gehua

0476

Optimus

0021

Sejin

1602

Vortex View

0883

General Instrument

0476 0810 0276 0003

Pace

1877 0237 0008

Signature

0011

Zenith

0000 0525 0899

Brand

Codes

Brand

Codes

Brand

Codes

Brand

Codes

AlphaStar

0772

Fortec Star

1550

Legend

0269

Realistic

0052

Amino

1615

Galaxis

0270

1226 1414 1750

Samsung

BeauSAT

1586

0392 0566

Magnavox

0724 0722

SATELLITE

Century

0856

General Instrument

0869

MegaSat

1551

Channel Master

0212

GOI

0775 1775

Memorex

0724 0269

Sanyo

1219

Chaparral

0053 0209 0216

Goodmans

1246

Mitsubishi

0749

SKY

0856 1856 0099

1806

Gradiente

0856

Motorola

0869 0856

Sony

0639 1639 1640

Crossdigital

1109

Hisense

1535

NEC

0102 0178 1270

Star Choice

0869

Digiturk

1076

Hitachi

0819 1250

Netsat

0099

Star Trak

0180

DirecTV

1377 0392 0566 0639

Homecable

0238

Next Level

0869

STS

0210

1639 1142 0247 0749

HTS

0775 1775

OctalTV

1505

Tivo

1749 0724 0819 1856

Hughes

0749 1749 1442

Panasonic

0247 0701 0152

1076 1108 0099 1109

Hughes Network Systems 1142 0749 1749 1442

Pansat

0647 1551 1807

1392 1414 1442 1443

1443 1444 1538 1750

Paysat

0724

Philips

1444 1538 1609 1640

Humax

1790

1750

iLo

1535

1775

Innova

0099

0210

Pioneer

1142 1442 1443 1444
1538

Toshiba

0749 1749 0790 0819
0082 1285

1142 0749 1749 0724

UltimateTV

1392 1640

0819 0856 1076 0722

Ultrasat

1806

0099 1442

Uniden

0329 1442

0724 0722 0052 0074
0076 0238

Dishpro

1505 1005 0775 1775

IQ Prism

0210

Proscan

0392 0566

US Digital

1535

Eastern

1612

Janeil

0152

Proton

1535

USDTV

1535

Echostar

1505 1005 0775 0159

Jerrold

0869

RadioShack

0869

Voom

0869

0269 0280 1170 1775

JVC

0775 1170 1775

RCA

0392 0566 0855 0143

Zenith

0856 1856

0775 1775

Lava

1631

Expressvu

1609

Coolsat

Dish Network System 1505 1005 0775 1170

1377 1142 1276 1108
1109 0270 1243 1442

1392

PDP_PRO1540HD.book Page 95 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features

VCR
Codes

Brand

Codes

Brand

Codes

Brand

Codes

ABS

1972

Craig

0271

Go Video

0240 0432 0526 0649

0037 0045 0042 0209

Admiral

0048 0209 0479

Crown

0072 0278 0020

Adventura

0000

Curtis Mathes

0060 0035 0162 0041

GoldHand

0072

Linksys

1972

Aiko

0278

0760 1035

GoldStar

0037 0209 0038 0225

Lloyd’s

0000 0208

Aiwa

0037 0000 0124 0307

Cybernex

0240

0479 1137

CyberPower

1972

0041 0061 0106 0175

Cyrus

0081

0242

Daewoo

Akai

0663 1137 1150

0038 0040 1037 1137

0226 1137 1237

Loewe

0037 0081

Goodmans

0037 0000 0072 0278

Logik

0240 0072

0020 0062

Lunatron

1137

0045 0104 0278 0020

Gradiente

0000 0008

Luxor

0048 0104 0043 0046

Akiba

0072

0046 0210 0212 0561

Graetz

0240 0104 0041

Akura

0271

1137 1278

Granada

0081 0104 0046

LXI

0037

Alba

0209 0072 0278 0020

Dansai

0072

Grandin

0037 0000 0072

M Electronic

0000 0038

Alienware

1972

Daytron

0020

Grundig

0081 0072 0034 0207

Magnasonic

0593 1278

Allegro

1137

De Graaf

0042 0166

0226 0378

Magnavox

0035 0039 0081 0000

Ambassador

0020

Decca

0081 0000

Hanseatic

0037

America Action

0278

Dell

1972

Haojie

0240

Magnin

0240

American High

0035

Denon

0042

Harley Davidson

0000

Manesth

0045 0072

Amoisonic

0479

DirecTV

0739

Harman/Kardon

0081 0038 0075

Marantz

0035 0081 0062

Amstrad

0000

Dual

0041

Harwood

0072

Marta

0037

Anam

0162 0037 0240 0278

Dumont

0081 0000 0104 0105

HCM

0072

Matsui

0209 0208

0226 1037

Durabrand

0039 0038

Headquarter

0046

Matsushita

0035 0162 0226 0227

Anam National

0162 0226

Dynatech

0000

Hewlett Packard

1972

Anitech

0072

Elbe

0038

HI-Q

0047

Media Center PC

1972

ASA

0037 0081

Elcatech

0072

Hinari

0240 0072 0208

MEI

0035

Asha

0240

Electrohome

0037 0043

Hitachi

0037 0240 0000 0042

Memorex

Asuka

0037

Electrophonic

0037

0041 0065 0082 0089

0039 0047 0240 0000

Audiovox

0037 0278

Emerex

0032

0105 0166 0235 0292

0104 0209 0046 0307

Awa

0043

Emerson

0035 0037 0184 0240

1037

0479 1037 1048 1162

Baird

0000 0104 0041

0045 0000 0121 0043

Howard Computers

1972

Basic Line

0072 0278 0020

0209 0002 0278 0208

1972

Beaumark

0240

0061 0212 0479 0561

Bell & Howell

0104

0593 1278 1479 1593

Blaupunkt

0162 0034 0226 0227

ESA

BPL

0046

ESC

Brandt Electronique

0041

EverFocus

1346

iBUYPOWER

1972

Microsoft

1972

Broksonic

0184 0121 0209 0002

Ferguson

0041

Imperial

0000

Mind

1972

0062 0106

0149 0563 0593 1781

1162

0035 0162 0037 0048

1237 1262
Memphis

0072

Hughes Network Systems 0042 0739

Metronic

0081

Humax

0739

Metz

0162 0037 0227

1137

Hush

1972

MGA

0240 0043 0061

0240 0278

Hypson

0072

MGN Technology

0240

0479 1479 1815

Fidelity

0000

Interfunk

0081

Minolta

0042 0105

Bush

0209 0072 0278

Finlandia

0081 0104

ITT

0240 0104 0041 0046

Mitsubishi

0081 0067 0043 0041

Calix

0037

Finlux

Canon

0035 1143

Capehart

0020

Carver

0081

Firstline

0081 0000 0042 0104

English

Brand

0106

0061 0075 0173 0214

0105

ITV

0037 0278

0037 0045 0043 0209

Jensen

0041

Motorola

0035 0048

0072

JVC

0045 0067 0041 0008

MTC

0240 0000

0242 0443 0807

Catron

0020

Fisher

0047 0104 0046

0206 0207 0366 1162

Multitech

0000 0072

CCE

0072 0278

Frontech

0020

1707

Murphy

0000

CGE

0000

Fuji

0035 0033

Kaisui

0072

Myryad

0081

Changhong

0048 0081

Fujitsu

0045 0000 0366

KEC

0037 0278

NAD

0104 0058

Cimline

0072

Funai

0000 0593 1335 1593

Kendo

0209 0106

National

0226

Cineral

0278

Garrard

0000

Kenwood

0067 0041 0038

NEC

0035 0037 0048 0104

CineVision

1137

Gateway

1195 1196 1972

KLH

0072

0067 0041 0038 0008

Citizen

0037 0278 1278

0060 0035 0240 0065

Kodak

0035 0037

0040 0050 0082 0206

Clatronic

0020

0202 0226 0760 0761

Kolin

0043 0041

Colt

0072

0807 1035 1060

Korpel

0072

Neckermann

0081

Condor

0020

GEC

0081

Lenco

0278

Nesco

0072

Craig

0037 0047 0240 0072

General

0045 0020 0366

Leyco

0072

Newave

0037

0457

95
En

PDP_PRO1540HD.book Page 96 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features
VCR
Brand

Codes

Brand

Codes

Brand

Codes

Brand

Nikko

0037

Pye

0081

SEG

0240

Tensai

0000

Nikon

0034

Qisheng

0060

SEI

0081

Thomas

0000

Niveus Media

1972

Quarter

0046

Seleco

0041

Thomson

0060 0067 0041 0202

Noblex

0240

Quartz

0046

Semp

0045

Thorn

0104 0041

Nokia

0240 0104 0041 0046

Quasar

0035 0162 0077 1035

Sensory Science

0649 1155

Tivo

1162

Sentra

0020

Sharp

0106
0041

Quelle

0081

Northgate

1972

Radiola

0081

Oceanic

0000 0041

RadioShack

0000 1037

Shinco

0000

0043 0209 0041 1996

Olympus

0035 0226

Radix

0037

Shintom

0104 0072

1972 1145 1008 0845

Onkyo

0222

Randex

0037

Shogun

0240

0377 0366 0212 0210

Optimus

1062 0162 0037 0048

RCA

0060 0035 0240 0000

Siemens

0037 0081 0104

0104 0058 0432 0593

0042 0149 0077 0105

Silva

0037

Totevision

0037 0240

1048 1162 1262

0106 0065 0202 0226

Singer

0045 0072

Touch

1972

Optonica

0062

0058 0760 0761 0807

Sinudyne

0081

Triumph

0208

Orion

0184 0121 0209 0002

0880 1035 1060

Solavox

0020

Uher

0240

TMK
Toshiba

0240

Sonic Blue

0614 0616 1137

Unitech

Sonolor

0046 0062

Universum

ReplayTV

0614 0616

Sontec

0037

0037 0041 0072

Rex

0041

Sony

0035 0032 0033 0000

Otto Versand

0081

Palladium

0240 0208
0081 0045 0042 0067

0057 0008

0000 0104 0046 0062

0037 0000 0072

Realistic

0048 0209 0062 0807
0848 1048

0035 0037 0048 0047

Osaki

Panasonic

0037 0081 0240 0000
0106

Vector

0045

1062 0035 0162 0077

Ricavision

1972

0011 0022 0034 0275

Vector Research

0038 0040

0225 0226 0227 0246

Ricoh

0034

0636 1032 1232 1546

Victor

0067 0041 0008

0378 0616 1035 1162

Rio

1137

1262

Roadstar

0037 0240 0072 0278

Stack 9

1702 1703 1896 1972

Video Concepts

0045 0040 0061

1972

Videomagic

0037

Pathe Marconi

0041

Runco

0039

STS

0042

Videosonic

0240

Penney

0035 0037 0240 0042

Saba

0041 0206 0207

Sunstar

0000

Viewsonic

1972

0038 0040 1035 1237

Saisho

0209 0208

Suntronic

0000

Villain

0000

Pentax

0042 0065 0105

Salora

0043 0046 0075 0106

Sylvania

0035 0081 0000 0043

Voodoo

1972

Perdio

0000

0593 1593 1781

Wards

0060 0035 0048 0047

Philco

0035 0000 0209 0038

Sampo

0037 0048

Symphonic

0000 0593 1593

0081 0240 0000 0042

0226 0479 0561

Samsung

0072 0149 0062 0212

Philips

0443
0240 0045 0210 0212

Systemax

1972

0035 0081 0000 0062

0432 0649 0663 0739

Tagar Systems

1972

0226 0563 0593 0618

0760 1014

Tandy

0000 0104

Wharfedale

0760
0593

0739 1081 1181 1266

Sanky

0048 0039

Tashiko

0037 0000

White Westinghouse

0209 0072

Phonola

0081

Sansui

0000 0067 0209 0041

Tatung

0081 0045 0000 0067

XR-1000

0035 0000 0072

Pilot

0037

0041 0008 0366

Yamaha

0041 0038

Pioneer

0081 0042 0067 0058

0000 0041 0278 0307

Yamishi

0072
0072

0082 0271 0479 1479
Sanyo

0047 0240 0104 0046

Teac

0526 0593

Yokan

Polk Audio

0081

SBR

0081

Tec

0020

Yoko

0240 0020

Portland

0020

Schaub Lorenz

0000 0104 0041

Technics

0035 0162 0226 0246

Zenith

0039 0033 0000 0209

Profitronic

0240

Schneider

0081 0000 0072

Teco

Proline

0000

Scott

0184 0045 0121 0043

Proscan

0060 0202 0760 0761

0168 0206 0235 1337

1060

0618 0636 0739 1337
1996

Nordmende

0208 0479 1479 1815

Codes

0159 0372

Sears

0035 0037 0048 0041

0034 0479 1137 1139

0038 0040

0210 0212

Teknika

0035 0037 0000

0035 0037 0047 0000

Teleavia

0041

Protec

0072

0042 0104 0046 0057

Telefunken

0041

Pulsar

0039

0105 1237

Tenosal

0072

1479
ZT Group

1972

PDP_PRO1540HD.book Page 97 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features

PVR
Codes

Brand

Codes

Brand

Codes

Brand

Codes

ABS

1972

Niveus Media

1972

Systemax

1972

Alienware

1972

Hughes Network Systems 0739

Northgate

1972

Tagar Systems

1972

CyberPower

1972

Humax

0739

Panasonic

0616

Tivo

0618 0636 0739

Dell

1972

Hush

1972

Philips

0618 0739

Toshiba

1008 1972

DirecTV

0739

iBUYPOWER

1972

RCA

0880

Touch

1972
1972

EverFocus

1346

Linksys

1972

ReplayTV

0614 0616

Viewsonic

Gateway

1195 1196 1972

Media Center PC

1972

Sonic Blue

0614 0616

Voodoo

1972

Hewlett Packard

1972

Microsoft

1972

Sony

0636 1972

ZT Group

1972

Howard Computers

1972

Mind

1972

Stack 9

1972

Codes

Brand

Codes

Brand

Codes

Brand

Codes

English

Brand

DVD
Brand
Acoustic Solutions

0730 1242

CineVision

0876 0833 0869

Gateway

1073 1077 1158 1194

Landel

0826

Adcom

1094

Citizen

1277

0522 0815 0717

Lasonic

0798 1173

Go Video

1533

Advent

1016

Classic

1385

0744 0715 0741 0783

Lecson

Afreey

0698

Clatronic

1165

0833 0869 1044 1075

Lenoxx

1127

Aiwa

0641

Coby

0778 0852 1086 1107

1099 1144 1148 1158

0591 0741 0801 0869

Akai

0695 0770 0899 1089

Alba

0672 0539 0717

Craig

0831

Go Vision

1071 1072

LiteOn

1058 1158 1416 1440

1165 1177 1351

1526

1304 1443 1730

Alco

0790

Curtis Mathes

1087

GoldStar

0741

Loewe

0511 0741

Allegro

0869

CyberHome

0816 0874 1019 1023

Goodmans

0790 1004

Logix

0783

Altacom

1224

1024 1117 1129 1502

GPX

0699 0769

Lunatron

0741

1537

Gradiente

0490 0651

Magnavox

0503 0539 0646 0675

Amphion Media Works 0872 1176 1245

0821 1268 1506

AMW

0872 1176 1245

Cydectin

1074

Greenhill

0717

Apex Digital

0672 0717 0755 0794

Daewoo

0784 0705 0770 0833

Grundig

0539 0695 0705

Malata

0782 1159

0869 1169 1172 1234

GVG

1169

Marantz

0539

0796 0797 0830 1004

1242 1441 1443

H&B

1421

Matsui

0672

Arcam

0732

Dansai

0770

Harman/Kardon

0582 0702

McIntosh

1533 1273 1373

Aspire Digital

1168 1407

Dantax

1089

Hitachi

0573 0664 0695 1247

Memorex

0690 0695 0831 1270

Audiologic

0736

Daytek

0872

Hiteker

0672

Metronic

0690

1020 1056 1061 1100

Audiovox

0790 1041 1071 1072

Decca

0770

iLo

1348 1472

Microsoft

0522

1121 1122

Denon

0490 0634

Initial

0717 1472

Minato

0752

Axion

1071 1072 1193

Denver

0778 1107 1316

Innovative Technology 1542

Minowa

1165

B&K

0655 0662

Desay

1407 1455

Integra

Mintek

0839 0717 1472

1316 1609 1610

0571 0627

BBK

1224

Diamond Vision

IRT

0783

Mirror

0752

Bel Canto Design

1571

Dick Smith Electronics 0833 1730

Jaton

1078

Mitsubishi

1521 0521

Bellagio

1245

Digitor

0690

JBL

0702

MixSonic

1130 1611

Blaupunkt

0717

Digitrex

0672 1056

Jensen

1016

Momitsu

1082

Blue Parade

0571

Digix

1272

JMB

0695

MTlogic

1265

Broksonic

0695 0868 1419

Disney

0675 1270

JSI

1423

Mustek

0730 1730

Bush

0690

DiViDo

0705

JVC

0558 0623 0867 1164

Myryad

0894

Byd:sign

0872

DSE

0833 1730

1275 1602

NAD

0591 0692 0741

California Audio Labs 0490

Dual

1068 1085

jWin

1049 1051

Nakamichi

1222

Cambridge Soundworks 0690

Durabrand

1127

Kawasaki

0790

NEC

0785 0869

Cary Audio Design

1477

DVD2000

0521

Kenwood

0490 0534 0682 0737

Nesa

0717

CAVS

1057

ECC

0730

KLH

0717 0790 1020 1149

Next Base

0826

Celestial

1020

Emerson

0591 0675 0821 1268

1261

NexxTech

1402

Centrex

0672 1004

Enterprise

0591

Konka

0711 0719 0720 0721

Nintaus

1051

Centrios

1577

ESA

1443

Koss

0651 0896 1423

Norcent

1003 0872 1107 1265

Changhong

0627 1061

Fintec

1169

Kreisen

1421

Cinea

0831

Fisher

0670

Krell

1498

Olidata

0672

Cinego

1399

Funai

0675 1268 1334

Lafayette

1369

Onkyo

0503 0627 0792

1457

97
En

PDP_PRO1540HD.book Page 98 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features
DVD
Brand

Codes

Brand

Codes

Brand

Codes

Brand

Codes

Oppo

1224

Proscan

0522

Shinco

0717

Toshiba

0503 0695 1045 1154

OptoMedia Electronics 0896

ProVision

0778

Shinsonic

0533 0839

TRANS-continents

0831 1165

Orion

1419

Qwestar

0651

Sigma Designs

0674

Tredex

0799 0800 0803 0804

Oritron

0651

RCA

0522 0571 0717 0790

Slim Art

0784

TYT

0705

Otic

0826

0822 1022 1132 1193

SM Electronic

0690 0730

Umax

0690

Pacific

0831

Recco

0698

Sonic Blue

0869 1099

Universum

0591

Palsonic

0672 0852

Reoc

0752

Sony

0533 1533 0864 1033

Urban Concepts

0503

Panasonic

0503 0490 0632 0703

Revoy

0699

1069 1070 1431 1432

US Logic

0839

1010 1011 1362 1462

Rio

0869

1433 1548

Venturer

0790

1490 1762

RJTech

1360

Sova

1122

Vialta

1509

peeKTon

1224

Roadstar

1051

Sungale

1074 1342 1532

Viewmaster

1224

Philco

0690 0790

Rotel

0623 1178

Superscan

0821

Vizio

1064 1226

Philips

0503 0539 0646 0675

Rowa

0823 1004

SVA

0717 0860 1105

Vocopro

1027

0854 1158 1260 1267

Sampo

0698 0752 1501

Sylvania

0675 0821 1268

Wesder

0699

1354

Samsung

0490 0573 0744 0820

Symphonic

0675 1268

Wintel

1130

PianoDisc

1024

0899 1044 1075

TAG McLaren

0894

Xbox

0522

Pioneer

0525 0571 0631 0632

Sansui

0695

Tatung

0770

XMS

0770

1475 1476 1571

Sanyo

0670 0695 0873

Teac

0571 0717 0692 0790

Xoro

1173

1020 1061 1086 1245

Schneider

0783

0809 0833

Xwave

1001

Yamada

Polaroid

1316 1478 1480 1482

Schwaiger

0752

Technics

0490 0703

Polk Audio

0539

Semp

0503

Technosonic

0730

0872 1004 1056 1158

Portland

0770

Sensory Science

1158

Techwood

0692

Yamaha

0490 0539 0545 0817

Prima

1016

Sharp

0630 0675 0752 1256

Tedelex

0690

Yamakawa

0872

Primare

0886 1467 1618

1419

Terapin

1031

Zenith

0503 0591 0741 0869

Princeton

0674

Sharper Image

1117

Theta Digital

0571

Zeus

0784

Proceed

0672

Sherwood

0633 0770 1043 1077

Thomson

0522

Zoece

1265

Brand

Codes

Brand

Codes

Brand

Codes

Brand

Codes

Apex Digital

1056

Funai

0675 1334

Loewe

0741

Sensory Science

1158

Aspire Digital

1168

Gateway

1073 1158 1194

Magnavox

0646 1506

Sharp

0630 0675 1419

Coby

1086

Go Video

0741 1158 1304 1730

Mustek

1730

Sony

1033 1069 1070 1431

CyberHome

1129 1502

H&B

1421

Panasonic

0490 1010 1011

Denon

0490

iLo

1348

Philips

0646 1158

Sylvania

0675

Dick Smith Electronics 1730

JVC

1164 1275

Pioneer

0631 1475 1476

Yamada

1056 1158 1416

Digitrex

1056

Kreisen

1421

Polaroid

1086

Zenith

0741

DSE

1730

0741

RCA

0522

Emerson

0675

LiteOn

1158 1416 1440

Samsung

0490

Brand

Codes

Brand

Codes

Brand

Codes

Brand

Codes

Aiwa

0203

Magnavox

0194 0217 0241

Philips

0064 0194

Sega

0023

Carver

0064 0194 0323

Marantz

0064 0194

Pioneer

0059 0023

Sharp

0001

1416

DVD-R

1432 1433

98
En

Denon

0059 0172 0241

Mitsubishi

0059 0241

Polk Audio

0194

Sony

0193 0201 0270

Disco Vision

0023

NAD

0059

Quasar

0204

Technics

0204

Funai

0203

Nagsmi

0059

Realistic

0203

Telefunken

0059

GoldStar

0172

NEC

0286

Renaissance

0323

Theta Digital

0194

Harman/Kardon

0194

Optimus

0059

Salora

0064

Victor

0245

Hitachi

0023 0395

Panasonic

0204

Samsung

0323

Yamaha

0217

PDP_PRO1540HD.book Page 99 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features
Receiver control buttons
When a Pioneer receiver is connected to the display, use
buttons 1 to 3 to operate the receiver.
When a non-Pioneer receiver is connected to the display, the
signals for 1 to 3 must first be “learned”. See page 92.

English

Using the remote control unit to control
other devices

RECEIVER  (STANDBY/ON)
Turns the Pioneer receiver power On and Off.

RECEIVER INPUT
Selects the input source connected to the Pioneer
receiver.

RECEIVER VOL +/–
Adjusts the Pioneer receiver volume level
Press VOL + to increase the volume and VOL – to decrease
it.

NOTE
• The color-highlighted buttons on the remote control can
memorize the control signal from another device’s remote
control.

1
2

3
Mode switch
(with “TV”
selected)

99
En

PDP_PRO1540HD.book Page 100 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features
CBL/SAT control buttons

1
6
2
7

When the CBL/SAT function has been preset by the remote
control’s learning function, the remote control buttons
function as shown below.
• When the Mode switch is set to CBL/SAT, the cable
converter or satellite broadcast tuner connected to the
display, use the buttons shown below to operate the device
(3, 4, 5, 8 and 9 for cable converters and 1 to 7 for satellite
tuners):
• Cable converters or satellite broadcast tuners made by other
manufacturers not listed in the system can be controlled
using the remote control if buttons 1 to 9 have already
learned the functions. See page 92.

SAT MENU
Displays the satellite broadcasting menu screen

ENTER,
ENTER:

/ / /
Activates the selected function

/ / / : Selects items on the SAT GUIDE screen or
SAT MENU screen

8
4

0–9
Press a button (or buttons) that corresponds to the
channel that you want to watch

9
4

CH +/–
Selects a higher or lower channel

SOURCE 
Turns the device sending the image On and Off

Mode switch
(with “CBL/SAT”
selected)

SAT GUIDE
Displays the satellite broadcasting guide screen
• Set up this button with the learning function if necessary

RETURN
When the CBL/SAT menu is displayed, restores the
immediately previous screen

CH ENTER*
Enters the selected channel with the direct channel
selection buttons

CH RETURN*
Switches between the current channel and the previous
channel you were watching

* Some cable converter manufacturers do not preset CH

ENTER and CH RETURN. Set up these buttons with the
learning function if necessary.

NOTE
• CABLE and SAT cannot be selected at the same time.
• The color-highlighted buttons on the remote control can
learn the control signal from another device’s remote
control.

100
En

PDP_PRO1540HD.book Page 101 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features

13
VCR control buttons

English

When the VCR is preset by the remote control’s learning
function, the remote control buttons function as follows:
(Mode switch must be set to VCR).
• Press the input selector button (INPUT 1–6) that matches
the input terminal connected to the VCR. The VCR can be
operated using 1 to 8.
• VCRs made by manufacturers not listed in the system can be
controlled using the remote control if buttons 1 to 8 have
learned the functions. See page 92.

CH +/–
Selects the channel on the VCR

 (PLAY)
Selects playback

 (RWD)
Rewinds the tape and allows picture search

SOURCE 
Turns the power of the VCR On and Off

 (PAUSE/STILL)
Pauses playback and displays still pictures

1
2
3
4
5

 (FF)
Rapidly advances the tape and allows picture search

6
7
8

 (REC)
Starts recording

8
Mode switch
(with “VCR”
selected)

 (STOP)
Stops tape transport

NOTE
• The color-highlighted buttons on the remote control can
learn the control signal from another device’s remote
control.

101
En

PDP_PRO1540HD.book Page 102 Wednesday, August 2, 2006 6:01 PM

Useful Remote Control Features
1

CH +/– (DVD recorder only)
Changes the channel of the tuner built into the DVD
recorder

 (PLAY)
Selects playback

 (SCAN)/ (CHAPTER SEARCH)
Continue pressing to go backward
Pressing quickly once takes you to the start of the playing
chapter. Each time it is pressed, playback jumps to the start
of previous chapter.

7
8
4

SOURCE 
Turns the power of the DVD player or DVD recorder On and
Off

9
5

 (PAUSE/STILL)
Pauses playback and displays still pictures

DVD MENU (DVD, DVD recorder)
Displays the DVD menu

DVD TOP MENU (DVD, DVD recorder)
Displays the DVD top menu

1
2
3
4
5

ENTER,
ENTER:

/ / /

(DVD, DVD recorder)

Activates the selected function

/ / / : Selects items on the DVD MENU screen

10
11
12

RETURN
When the DVD menu is displayed, restores the
immediately previous screen

Mode switch
(with “DVD/
DVR” selected)

10  (SCAN)/ (CHAPTER SEARCH)
Continue pressing for fast forward
Pressing quickly once takes you to the start of the next
chapter. Each time it is pressed, playback jumps to the start
of the next chapter.

11  (REC) (DVD recorder only)
Starts recording

DVD/DVR control buttons
When the DVD/DVR is preset by the learning function of the
remote control, the remote control unit buttons will function as
follows when the Mode switch of the remote control unit is set
to DVD/DVR.
• When the input selector button having the same number as
the input terminal connected to a DVD player or DVD recorder
is pressed, these players can be operated using 1 to 12.
• DVD players or DVD recorders made by other manufacturers
and not preset can also be operated using the remote control
unit if 1 to 12 have learned the functions. See page 92.

102
En

12  (STOP)
Stops playback
If pressing once fails to stop playback on the DVD player or
DVD recorder, press twice to open the disc tray.

11, 12 STOP REC (DVD recorder only)
Press and hold  then press  to stop recording. This
operation applies to Pioneer DVD recorders only.

NOTE
• A DVD player and a DVD recorder cannot be selected at the
same time.
• The color-highlighted buttons on the remote control can
learn the control signal from another device’s remote
control.
• The remote control buttons can control some LD players. For
the supported LD players, see the LD brands and codes on
page 98.

PDP_PRO1540HD.book Page 103 Wednesday, August 2, 2006 6:01 PM

Appendix
Appendix

Troubleshooting
Possible Solution

GENERAL

• No power

• Is the power cord disconnected? (See page 25)
• Has POWER been turned on? (See page 26)
• Check if you pressed TV  on the remote control. (See page 26)
If the indicator on the system lights up red, press TV .

• Power is suddenly turned off

• Is the sleep timer set? (See page 57)
• Check the power control setting. (See page 63)
• The system’s internal temperature has increased. Clear/clean the vents. (See page 20)
• A malfunction may have occurred in the home network module.

• The system cannot be operated

• External influences such as lightning, static electricity, etc., may cause failures.
Try turning off the Plasma Display or unplugging the power cord. Wait one to two minutes then restore
power to the panel.

• Remote control unit does not operate

• Check if POWER is Off. Activate the button when the POWER ON and STANDBY indicators are Off.
• Is the Mode switch set correctly? Slide it to the TV position. (See page 19)
• Are the batteries inserted with polarity aligned (+, –)? (See page 24)
• Are the batteries low? (Replace with new batteries.) (See page 24)
• Point the remote control directly at the panel’s remote control sensor. (See page 24)
• Is the panel under strong or fluorescent lighting?
• Is fluorescent light blinding the remote control sensor?

• POWER ON indicator or STANDBY
indicator is blinking

• The unit’s internal protective circuits may have been activated.
Unplug the panel’s power cord from the power outlet. Wait one to two minutes then plug in the panel again.
If the problem is not solved with this, contact the nearest Pioneer Authorized Independent Service Company,
or the Customer Support Division (see back cover).

English

Problem

PICTURE/SOUND

• Image and sound are absent

• Verify that the input source is a TV channel rather than from a PC or a DVD player. (See page 27)
• Check the Parental Control function. (See page 38)
Enter a password to temporarily cancel the Parental Control function. (See page 42)
• Check the cable connection with the antenna. (See page 23)
• Check the cable connection with the source device. (See pages 68 to 74)

• No picture

• Is the connection to other components correct? (See pages 68 to 73)
• Is a non-compatible PC signal being input? (See page 72)
• Is picture adjustment correct? (See page 58)

• Sound but no picture

• Check if energy-saving “Picture Off” option is selected. With this option selected, the screen is deactivated;
only audio is output. To restore the screen display, press any button other than VOL +/– and MUTING. (See
page 63)

• Picture but no sound

• Verify that the volume is set high enough to hear. (See page 28)
• Check if the sound is muted. (See page 28)
• When using a video or PC input source, verify that the audio terminals are also connected.
(See pages 68 to 70 and 72)

• Sound is reversed between the right and • Check if the speaker cable connections have been reversed between the right and left or if the speaker cable
left speakers
from either speaker has been disconnected. (See page 21)
• Sound but from only one speaker
• Has the balance been correctly adjusted? (See page 62)
• Picture is cut off

• Is the image position correct? (See page 64)
• Has the correct screen size been selected? (See page 66)

• Colors are too dark/light or appear
strange

• Adjust the picture tone. (See page 58)
• Is the room too bright? The picture may appear dim in a room that is too bright.

103
En

PDP_PRO1540HD.book Page 104 Wednesday, August 2, 2006 6:01 PM

Appendix
Problem

Possible Solution

OTHER

• TV-Guide data is unavailable

• If TV-Guide data cannot be obtained with ANT.A selected for cable connection, select ANT.B for over the air.
In addition, perform the TV-Guide setup again (see page 33):
- Select “No” for cable service on Screen 3.
- Select “Yes” for antenna service on Screen 5.
- Select “ANT B IN” on Screen 4.

• An external device connected to the
USB terminal does not operate

• Confirm that the device is connected to the display. (See page 76)
• Disconnect then reconnect the USB cable. (See page 76)
• Check that the USB cable is shorter than 5 m. (See page 76)
• Check if the USB cable is properly connected. (See page 76)
• Turn Off then On the main power to confirm that the USB device is working.
• Check if the external device works correctly after the USB device was restarted.
• Verify that the digital camera is set to take a picture.
• Confirm that the digital camera is placed in Mass Storage mode.
• To change the digital camera’s configuration, refer to the camera’s instruction manual.

• Photo data stored in a digital still
camera cannot be read through USB
interface

• Confirm that the device is connected to the display. (See page 76)
• Verify that the digital camera is turned On.

• Panel sounds/noises

• Panel generated sounds, examples: Fan motor noise, Electrical Circuit Humming/Glass Panel buzzing are
normal operation of a phosphor-based matrix display. Experiment with the available Energy Save modes to
find the best setting for your use. (See page 63)

• Screen shows uneven brightness on the • Play content that completely fills the screen until unevenness is minimized. Some signals may require the
sides
AV mode setting to be changed. (See page 65)
Home Media Gallery/NETWORK

• No servers are found

• Confirm that the PC is On and not in Standby or Sleep. (nothing is chosen in “Select Servers”). When the PC
has started with the “Wake On LAN” (WOL), check if the PC complies with WOL or if the WOL setup has
been properly done on the device manager for BIOS or Windows.
• Check the physical connections (hub, 100BASE-TX/10BASE-T, or crossed cable and other cable quality when
cabled directly to a PC). It is strongly recommended to use 100BASE-TX for playback quality and display
speed.
• Check the logical connections (IP Address setup, DHCP, etc.). Confirm the IP Address is correct if acquired
by Auto IP and Firewall setup. Also check if the IP Address is properly acquired with DHCP on the “Network
Setup” screen that follows the “Setup” menu.
• Check the PC if its media server (Windows Media Connect or DLNA compliant) is running. Restart if
necessary. Check if one or more servers are On (this may cause malfunction).
• Check if the PC is operating properly. Reboot the PC after confirming its specifications and setup.
• Check the media server setup. If a client is registered manually the setup procedure may have to be run
again. An option “Not Allowed” may have been selected for connections.
• Wait for a short period then select “Update to Latest Information” from the Tool Menu. (See page 78)

• No previously connected server(s) found • Confirm that the PC is On and not in Standby or Sleep. (nothing is chosen in “Select Servers”). When the PC
(items in “Select Servers” are dimmed)
has started with the “Wake On LAN” (WOL), check if the PC complies with WOL or if the WOL setup has
been properly done on the device manager for BIOS or Windows.
• Check the physical connections (hub, 100BASE-TX/10BASE-T or crossed cable and other cable quality when
cabled directly to a PC). It is strongly recommended to use 100BASE-TX for playback quality and display
speed.
• Check the logical connections (IP Address setup, DHCP, etc.). Confirm the IP Address when acquired by
Auto IP and Firewall setup. Also check if the IP Address is properly acquired with DHCP on the “Network
Setup” screen that follows the “Setup” menu.
• Check the PC if its media server (Windows Media Connect or DLNA compliant) is running. Restart it if
necessary. Check if one or more servers are On (this may cause malfunction).
• Check if the PC is operating properly. Reboot the PC after confirming its specifications and setup.
• Check the media server setup. A setup procedure may be required for connections if a client is registered
manually. An option “Not Allowed” may have been selected for connections.
• Wait for a while and select “Update to Latest Information” from the Tool Menu. (See page 78)
• An available server is selected but
cannot be navigated

• Check if the server is correctly set up for file sharing, if the target folder has been deleted, or if one or more
folders have been corrupted on the server.
• Check if there are too many files in each folder.

• A server is arbitrarily selected

• This arbitrary selection happens when the server you used before had been set to display the top menu
screen (if you reset it, other servers connected are also reset). When the “Single Server/USB” option is
selected on the “Auto Connection Setup” screen that follows the “Setup” menu, the server is automatically
accessed if only one server is connected. Use the Tool Menu to select the proper server. (See page 78)

• File/folder configuration differs from one • The Media Navigator displays the server contents as classified by the server.
server to another (strange configuration) • If no information (such as ID3 tag) is contained in the file, files cannot be classified on the server.

104
En

PDP_PRO1540HD.book Page 105 Wednesday, August 2, 2006 6:01 PM

Appendix
Problem

14
Possible Solution

Home Media Gallery/PLAYBACK

• Cannot play or display

• Check the physical connections (hub, 100BASE-TX/10BASE-T, or crossed cable and other cable quality when
cabled directly to a PC). It is strongly recommended to use 100BASE-TX for playback quality and display
speed.
• Check if the PC is operating properly. Reboot the PC after confirming its specifications and setup.
• Check if the file complies to the supported format, bit rate or profile. Also check if the file is damaged.
• Check if the leasing contract for the server has expired.
• When connected by a wireless LAN, check if the bit rate is sufficient.
• Some files that comply with the supported format may not be played back or displayed.
• It takes time to capture and display a large-sized image. If this is the case, no operation may be performed.
• See the Pioneer website (www.pioneerelectronics.com) for the formats that are supported.

English

• Image or sound is interrupted or
distorted (Block noise appears)

Home Media Gallery/FIRMWARE

• No updates are possible on USB

• Check if the device is Mass Storage Class compliant, if it is connected properly, nothing is damaged (power
unit, mode such as Mass Storage mode and media format, etc.), if it contains the supported files, and if the
speed of the device is sufficient (poor device speed may result in interrupted or delayed display of images
due to a bit-rate problem). When using a digital camera that is not Mass Storage Class compliant, insert the
Flash Memory card into the multi-card reader.
• Confirm that the device is correctly inserted or removed.
• Check that the firmware file has been correctly downloaded. Also check the file size.
• See the Pioneer website (www.pioneerelectronics.com) for details.

Home Media Gallery/USB

• USB devices are not properly recognized • Check if the device is Mass Storage Class compliant, if it is connected properly, nothing is damaged (power
unit, mode such as Mass Storage mode and media format, etc.), if it contains the supported files, and if the
speed of the device is sufficient (poor device speed may result in interrupted or delayed display of images
due to a bit-rate problem). When using a digital camera that is not Mass Storage Class compliant, insert the
Flash Memory card into the multi-card reader.
• Confirm that the device is correctly inserted or removed.
• No USB hub is supported. When you connect a home network, connect directly to the device’s USB port.
• Image or sound is interrupted or
distorted (Block noise appears)

• Verify that the file complies with the supported format, bit rate or profile. Also check the file for damage.
• Some files that comply with the supported format may not play back or display properly.
• Check if the device is Mass Storage Class compliant, if it is connected properly, nothing is damaged (power
unit, mode such as Mass Storage mode and media format, etc.), if it contains the supported files, and if the
speed of the device is sufficient (poor device speed may result in interrupted or delayed display of images
due to a bit-rate problem). When using a digital camera that is not Mass Storage Class compliant, insert the
Flash Memory card into the multi-card reader.

If one of the following error codes appear on screen, check the corresponding message.
Code

Message

Check

SD04 and
SD11

Powering off. Internal temperature too high.
Check temperature around PDP.

Check if the ambient temperature of the Plasma Display is high.

SD05

(PRO-1540HD/PRO-1140HD)
Internal protection circuit turns power off.
Is there a short in speaker cable?
(PRO-940HD)
Internal protection circuit turns power off.

Check the speaker cable connections between the Plasma Display and the speakers.

Contact the nearest Pioneer Authorized Independent Service Company or the
Customer Support Division. (See back cover)

105
En

PDP_PRO1540HD.book Page 106 Wednesday, August 2, 2006 6:01 PM

Appendix
This product in part uses “OpenSSL” software.
To the extent the OpenSSL software is being used, the following notification applies:
Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following
conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer
in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product
includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this
software without prior written permission. For written permission, please contact openssl-core@openssl.org.
5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior
written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed
by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written
by Tim Hudson (tjh@cryptsoft.com).

Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com)
All rights reserved.
This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to
conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are ahered to. The following
conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL
documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson
(tjh@cryptsoft.com).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a
product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual
message at program startup or in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following
conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer
in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This
product includes cryptographic software written by Eric Young (eay@cryptsoft.com)” The word ’cryptographic’ can be left out
if the rouines from the library being used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include
an acknowledgement: “This product includes software written by Tim Hudson (tjh@cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code
cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]
106
En

PDP_PRO1540HD.book Page 107 Wednesday, August 2, 2006 6:01 PM

Appendix

English

Copyright (c) 1998, 1999, 2000 Thai Open Source Software
Center Ltd and Clark Cooper
Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN
NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING ROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

“Portions of this software are copyright (c) The FreeType Project (www.freetype.org). All rights reserved.” [please replace
with the value from the FreeType version you actually use]
If only executable code is distributed, then the accompanying documentation must state that “this software is based in part on the
work of the Independent JPEG Group”
COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:
If you modify libpng you may insert additional notices immediately following this sentence.
libpng version 1.2.6, September 12, 2004, is Copyright (c) 2004 Glenn Randers-Pehrson, and is distributed according to the same
disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors
Cosmin Truta
libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are
distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of
Contributing Authors
Simon-Pierre Cadieux
Eric S. Raymond
Gilles Vollant
and with the following additions to the disclaimer:
There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our
efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of
satisfactory quality, performance, accuracy, and effort is with the user.
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c) 1998, 1999 Glenn Randers-Pehrson, and are
distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of
Contributing Authors:
Tom Lane
Glenn Randers-Pehrson
Willem van Schaik
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger
Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of
Contributing Authors:
John Bowler
Kevin Bracey
Sam Bushell
Magnus Holmgren
Greg Roelofs
Tom Tanner

107
En

PDP_PRO1540HD.book Page 108 Wednesday, August 2, 2006 6:01 PM

Appendix
libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.
For the purposes of this copyright and license, “Contributing Authors” is defined as the following set of individuals:
Andreas Dilger
Dave Martindale
Guy Eric Schalnat
Paul Schmidt
Tim Wegner
The PNG Reference Library is supplied “AS IS”. The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or
implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors
and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary, or consequential damages, which may
result from the use of the PNG Reference Library, even if advised of the possibility of such damage.
Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without
fee, subject to the following restrictions:
1. The origin of this source code must not be misrepresented.
2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.
3. This Copyright notice may not be removed or altered from any source or altered source distribution.
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a
component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment
is not required but would be appreciated.
A “png_get_copyright” function is available, for convenient use in “about” boxes and the like: printf (“%s”,png_get_copyright
(NULL)); Also, the PNG logo (in PNG format, of course) is supplied in the files “pngbar.png” and “pngbar.jpg (88x31) and
“pngnow.png” (98x31). Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the
Open Source Initiative.
Glenn Randers-Pehrson
glennrp@users.sourceforge.net
September 12, 2004
Copyright (c) 2002, Xiph.org Foundation
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following
conditions are met:
- Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in
the documentation and/or other materials provided with the distribution.
- Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products
derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
The GIFLIB distribution is Copyright (c) 1997 Eric S. Raymond
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN
NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Copyright (c) 1988-1997 Sam Leffler

108
En

PDP_PRO1540HD.book Page 109 Wednesday, August 2, 2006 6:01 PM

Appendix

IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
PROFITS, WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT
OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

English

THE SOFTWARE IS PROVIDED “AS-IS” AND WITHOUT WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR OTHERWISE,
INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Copyright (C) 1995-2004 Jean-loup Gailly and Mark Adler
“Copyright (c) 1998-2003 The OpenSSL Project. All rights reserved.”
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”

Linux Source Notice
The Pioneer Plasma Television is powered by utilizing the Linux operating system. The machine readable copy of the corresponding
source code is available for the cost of distribution. To obtain a copy, please visit
http://www.pioneerelectronics.com/ for more information.

GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change free software-to make sure the software is free for all its users.
This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors
commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.)
You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure
that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source
code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you
can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights.
These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that
you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they
know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to
copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this
free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not
the original, so that any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear
that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.

GNU General Public License
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be
distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a
“work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work
containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act
of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work
based on the Program (independent of having been made by running the Program). Whether that is true depends on what the
Program does.
109
En

PDP_PRO1540HD.book Page 110 Wednesday, August 2, 2006 6:01 PM

Appendix
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact
all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy
of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy
and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these
conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or
any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for
such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright
notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute
the program under these conditions, and telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms,
do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part
of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose
permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is
to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the
Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the
terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms
of Sections 1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost
of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be
distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is
allowed only for noncommercial distribution and only if you received the program in object code or executable form with
such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work,
complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus
the scripts used to control compilation and installation of the executable. However, as a special exception, the source code
distributed need not include anything that is normally distributed (in either source or binary form) with the major components
(compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies
the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent
access to copy the source code from the same place counts as distribution of the source code, even though third parties are
not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this
License.
However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so
long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify
or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore,
by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to
do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from
the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any
further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance
by third parties to this License.

110
En

PDP_PRO1540HD.book Page 111 Wednesday, August 2, 2006 6:01 PM

Appendix

English

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent
issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this
License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your
obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program
at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies
directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from
distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is
intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of
any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is
implemented by public license practices. Many people have made generous contributions to the wide range of software
distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he
or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the
original copyright holder who places the Program under this License may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such
new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies
to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later
version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may
choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to
the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR
OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR
ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU
FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to
make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively
convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is
found.

Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as
published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software
Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
111
En

PDP_PRO1540HD.book Page 112 Wednesday, August 2, 2006 6:01 PM

Appendix
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome
to redistribute it under certain conditions; type ’show c’ for details.
The hypothetical commands ’show w’ and ’show c’ should show the appropriate parts of the General Public License. Of course,
the commands you use may be called something other than ’show w’ and ’show c’; they could even be mouse-clicks or menu
items-whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the
program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program ’Gnomovision’ (which makes passes at compilers) written
by James Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine
library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do,
use the GNU Lesser General Public License instead of this License.

GNU Lesser General Public License
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2,
hence the version number 2.1.]

Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public
Licenses are intended to guarantee your freedom to share and change free software-to make sure the software is free for all its
users. This license, the Lesser General Public License, applies to some specially designated software packages-typically librariesof the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully
about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the
explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make
sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source
code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are
informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these
rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we
gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must
provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and
recompiling it. And you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal
permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified
by someone else and passed on, the recipients should know that what they have is not the original version, so that the original
author’s reputation will not be affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot
effectively restrict the users of a free program by obtaining a restrictive license from a patent holder.
Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use
specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser
General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We
use this license for certain libraries in order to permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking
a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the
entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code
with the library.
We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary
General Public License. It also provides other free software developers Less of an advantage over competing non-free programs.
These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license
provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it
becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library.
112
En

PDP_PRO1540HD.book Page 113 Wednesday, August 2, 2006 6:01 PM

Appendix

English

A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by
limiting the free library to free software only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body
of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the
whole GNU operating system, as well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that
is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between
a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the
latter must be combined with the library in order to run.

GNU Lesser General Public License
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder
or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this
License”). Each licensee is addressed as “you”.
A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application
programs (which use some of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based
on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library
or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter,
translation is included without limitation in the term “modification”.)
”Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source
code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used
to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act
of running a program using the Library is not restricted, and output from such a program is covered only if its contents
constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true
depends on what the Library does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided
that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty;
keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License
along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and
distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses
the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure
that, in the event an application does not supply such function or table, the facility still operates, and performs whatever
part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the
application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be
optional: if the application does not supply it, the square root function must still compute square roots.) These requirements
apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be
reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those
sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is
a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is
to exercise the right to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library)
on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library.
To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License,
version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has
appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies
to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code
of the Library into a program that is not a library.
113
En

PDP_PRO1540HD.book Page 114 Wednesday, August 2, 2006 6:01 PM

114
En

Appendix
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under
the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source
code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to
copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties
are not compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled
or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and
therefore falls outside the scope of this License. However, linking a “work that uses the Library” with the Library creates an
executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the
library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.
When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may
be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work
can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline
functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative
work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section
6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce
a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit
modification of the work for the customer’s own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are
covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you
must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this
License.
Also, you must do one of these things:
a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever
changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable
linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source
code, so that the user can modify the Library and then relink to produce a modified executable containing the modified
Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be
able to recompile the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time
a copy of the library already present on the user’s computer system, rather than copying library functions into the
executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the
modified version is interface-compatible with the version that the work was made with.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in
Subsection 6a, above, for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the
above specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for
reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything
that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally
accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an
executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library
facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work
based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library
facilities. This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining
where to find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any
attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your
rights under this License. However, parties who have received copies, or rights, from you under this License will not have their
licenses terminated so long as such parties remain in full compliance.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify
or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore,
by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do
so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

PDP_PRO1540HD.book Page 115 Wednesday, August 2, 2006 6:01 PM

Appendix

English

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from
the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not
impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing
compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent
issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this
License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your
obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library
at all.
For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly
or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from
distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is
intended to apply, and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of
any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is
implemented by public license practices. Many people have made generous contributions to the wide range of software
distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he
or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the
original copyright holder who places the Library under this License may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time.
Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies
to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later
version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose
any version ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with
these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to
the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR
OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE
LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR
ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU
FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY
OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
END OF TERMS AND CONDITIONS

115
En

PDP_PRO1540HD.book Page 116 Wednesday, August 2, 2006 6:01 PM

Appendix
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software
that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under
the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full
notice is found.

Copyright (C) year name of author
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as
published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software
Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the
library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library ’Frob’ (a library for tweaking knobs) written by James Random
Hacker.
signature of Ty Coon, 1 April 1990
Ty Coon, President of Vice
That’s all there is to it!

116
En

PDP_PRO1540HD.book Page 117 Wednesday, August 2, 2006 6:01 PM

Appendix

Specifications
60" Plasma Display
Model: PRO-1540HD

50" Plasma Display
Model: PRO-1140HD

42" Plasma Display
Model: PRO-940HD

Number of pixels

1365 × 768 pixels

1024 × 768 pixels

Audio Amplifier

13 W + 13 W (1 kHz, 10 %, 8 Ω)

Speakers

–

13 W + 13 W (1 kHz, 10 %, 8 Ω)
Woofer: 4.8 cm × 13 cm cone type
Tweeter: 2.5 cm semidome type

Surround System

SRS/FOCUS/TruBass

Power Requirement

120 V AC, 60 Hz, 460 W (30 W
Standby)

120 V AC, 60 Hz, 355 W (26 W
Standby)

120 V AC, 60 Hz, 312 W (26 W
Standby)

Weight

Main unit: 51.5 kg (113.6 lbs.)

Main unit: 34.3 kg (75.7 lbs.)

Main unit: 29.2 kg (64.4 lbs.)
Stand: 2.5 kg (5.5 lbs.) (including
bolts)
Total: 31.7 kg (69.9 lbs.)

Reception System (Digital)
Circuit type
Tuner

VHF Ch. 2 to 13 UHF Ch. 14 to 69

CATV

Ch. 2 to 135
Dolby Digital

Reception System (Analog)

Terminals

ATSC Digital TV system
8VSB/64QAM/256QAM/QPSK demodulation

VHF/UHF

Audio
format

American TV standard NTSC system

Circuit type

Video signal detection PLL full synchronous detection, PLL digital
Synthesizer system

Tuner

VHF/UHF

VHF Ch. 2 to 13 UHF Ch. 14 to 69

CATV

ANT/CABLE A IN Ch. 1 to 135 ANT B IN Ch. 1 to 125

Audio multiplex

BTSC system

Rear

75 Ω UNBAL, F Type for DTV/VHF/UHF/CATV in

Side

English

Item

ANT/CABLE A IN
ANT B IN

75 Ω UNBAL, F Type for VHF/UHF/CATV in Loop out

INPUT 1

S-VIDEO in, VIDEO in, AUDIO in

INPUT 2

COMPONENT VIDEO in, S-VIDEO in, VIDEO in, AUDIO in

INPUT 3

COMPONENT VIDEO in, AUDIO in

Analog RGB in, AUDIO in

INPUT 5

HDMI in*, AUDIO in

INPUT 6

HDMI in*, AUDIO in

MONITOR OUT

VIDEO out, AUDIO out

Digital Audio Output

Optical

G-LINK

ETHERNET

CONTROL IN

CONTROL OUT

SPEAKER

8 Ω to 16 Ω

SUB WOOFER OUTPUT

Variable

CableCARD

Point of Deployment

INPUT 4

COMPONENT VIDEO in, VIDEO in, AUDIO in

USB

USB in**

On-screen display languages

8 Ω to 16 Ω

–

English/French/Spanish

This conforms to HDMI1.1 and HDCP1.1.
HDMI (High Definition Multimedia Interface) is a digital interface that sends both video and audio signals through a single
cable.
HDCP (High-bandwidth Digital Content Protection) is a technology used to protect copyrighted digital content that use Digital
Visual Interface (DVI).
** This conforms to USB 1.1 and 2.0 specifications.
• Design and specifications are subject to change without notice.
117
En

PDP_PRO1540HD.book Page 118 Wednesday, August 2, 2006 6:01 PM

Appendix
Dimensions
PRO-1540HD
Unit: mm (inch)
118
(4-21/32)
1470 (57-7/8)

880
(34-21/32)

PRO-1140HD
Unit: mm (inch)
115
(4-1/2)
1224 (48-3/16)

717
(28-1/4)

PRO-940HD
Unit: mm (inch)
115
(4-1/2)
1040 (40-15/16)

679
(26-3/4)

719
(28-5/16)

559 (22)

118
En

273
(10-3/4)

PDP_PRO1540HD.book Page 119 Wednesday, August 2, 2006 6:01 PM

Appendix

Trademarks
English

• In the United States, TV GUIDE and other related marks are registered trademarks of Gemstar-TV Guide International, Inc. and/
or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental, Inc. and is used under license by GemstarTV Guide International, Inc.
• FOCUS, WOW, SRS and h® symbol are trademarks of SRS Labs, Inc.
FOCUS and WOW technologies are incorporated under license from SRS Labs, Inc.
• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
• This product includes FontAvenue® fonts licensed by NEC Corporation. FontAvenue is a registered trademark of NEC
Corporation.
• DDC is a registered trademark of Video Electronics Standards Association.
• CableCARD is a trademark of Cable Television Laboratories, Inc.
• This software is based in part on the work of the independent JPEG Group.
• The names of the companies or institutions are trademarks or registered trademarks of the respective companies or institutions.
• The PlaysForSure logo, Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation
in the United States and/or other countries.
• DLNA and DLNA CERTIFIED™ are trademarks and/or service marks of Digital Living Network Alliance.

License
• The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its
affiliates.
• Content owners use Windows Media digital rights management technology (WMDRM) to protect their intellectual property,
including copyrights. This device uses WMDRM software to access WMDRM-protected content. If the WMDRM software fails
to protect the content, content owners may ask Microsoft to revoke the software’s ability to use WMDRM to play or copy
protected content. Revocation does not affect unprotected content. When you download licenses for protected content, you
agree that Microsoft may include a revocation list with the licenses. Content owners may require you to upgrade WMDRM to
access their content. If you decline an upgrade, you will not be able to access content that requires the upgrade.
• This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of
this product is prohibited without a license from Microsoft.
• The DLNA logo is permitted to the product that has obtained a DLNA (Digital Living Network Alliance) certificate.

Patent
• The TV Guide On Screen system is protected by one or more of the following United States patents 4,908,713; 6,498,895;
6,850,693; 6,396,546; 5,940,073; 6,239,794 to Gemstar-TV Guide International, Inc. and/or its subsidiaries.

Disclaimer Notice
• Gemstar-TV Guide International Inc. and/or its related affiliates are not in any way liable for the accuracy or availability of the
program schedule information or other data in the TV Guide On Screen system and cannot guarantee service availability in your
area. In no event shall Gemstar-TV Guide International, Inc. and/or its related affiliates be liable for any damages in connection
with the accuracy or availability of the program schedule information or other data in the TV Guide On Screen system.

Copyright protection
• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other
limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Important Notice about software upgrade from Pioneer
Attention Pioneer PDP Owners:
Thank you for purchasing a Pioneer Digital Cable Ready (DCR) compatible Plasma TV.
You have purchased the most advanced product of its kind available today.
However, as technology advances, DCR systems may continue to evolve. To maintain compatibility with DCR systems and features,
your Plasma TV may benefit from, or require software upgrades.
As part of our commitment to our customers, Pioneer will send you upgrade software and instructions as needed to keep your
DCR compatible Plasma TV up to date with this technology.
Please take the time to register your DCR compatible Plasma TV at
www.pioneerelectronics.com
This registration enables us to keep you up to date on changes that may occur.
Thank you very much.
Note:
DCR function works only in the USA.
DCR is unavailable in Canada.
Software update for the Home Media Gallery
You can also update the software for the Home Media Gallery at the Pioneer website above. For details, see page 89.

119
En

PDP_PRO1540HD.book Page 120 Wednesday, August 2, 2006 6:01 PM

PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404

PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901

PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270

Printed in China

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Page Count                      : 120
Page Mode                       : UseThumbs
Page Layout                     : SinglePage
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:b2180eb3-ebf9-4686-8c25-0a3e6fc2e966
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Create Date                     : 2006:08:02 09:12:42Z
Modify Date                     : 2006:08:31 16:00:00+09:00
Metadata Date                   : 2006:08:31 16:00:00+09:00
Document ID                     : uuid:20080c03-2ed1-4b41-a90e-9b2d4c2eea33
Instance ID                     : uuid:aaff4095-2874-447a-8121-1660ac1f06f2
Format                          : application/pdf
Title                           : ARB1573-A
Creator                         : PMC
Description                     : Linked
Author                          : PMC
Subject                         : Linked

EXIF Metadata provided by EXIF.tools

Pioneer Pro 1140Hd Users Manual ARB1573 A

If not then 366322056PRO940HDOperatingInstructions Manual: ://www.pioneerelectronics.com/pio/pe/images/portal/cit_11221/366322056PRO940HDOperatingInstructions

If not then 366322046PRO1540HDOperatingInstructions Manual: ://www.pioneerelectronics.com/pio/pe/images/portal/cit_11221/366322046PRO1540HDOperatingInstructions

PRO-940HD to the manual e20c3aff-9fe0-4183-8742-cc4cfb47540b

Navigation menu

Versions of this User Manual:

Views

Navigation