Pioneer Sc 1222 K Owners Manual

2014-07-06

: Pioneer Sc-1222-K-Owners-Manual sc-1222-k-owners-manual pioneer pdf

Open the PDF directly: View PDF PDF.
Page Count: 112

DownloadPioneer Sc-1222-K-Owners-Manual
Open PDF In BrowserView PDF
Operating Instructions

AV Receiver

SC-

1222

-K

IMPORTANT
CAUTION

1)
2)
3)
4)
5)
6)
7)

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.

CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

D3-4-2-1-1_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En

Operating Environment

Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c*_A1_En

WARNING

Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the rear panel.
D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 20 cm at top, 10 cm at rear, and 20 cm at each
side).

WARNING

Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.

If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation).

11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.

13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
D3-7-13-69_En

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

D3-4-2-2-1a_A1_En

CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).

Caution
To prevent fire hazard, the Class 2 Wiring Cable
should be used for connection with speaker, and
should be routed away from hazards to avoid damage
to the insulation of the cable.

D3-4-2-2-2a*_A1_En

D3-7-13-67*_A1_En

D8-10-1-2_A1_En

WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product may expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.

D3-4-2-1-7b*_A1_En
D36-P5_B1_En

Information to User
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
D8-10-2_A1_En

2

IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF
THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON YOUR ENCLOSED
WARRANTY CARD AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
D36-AP9-1_A1_En

CAUTION
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit
to other equipment. To prevent electromagnetic
interference with electric appliances such as radios
and televisions, use shielded cables and connectors
for connections.
D8-10-3a_A1_En

This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En

This Class B digital apparatus complies with
Canadian ICES-003.

The Safety of Your Ears is in Your Hands

Get the most out of your equipment by playing it at a
safe level – a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing
“comfort level” adapts to higher volumes of sound, so
what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting
your equipment at a safe level BEFORE your hearing
adapts.

ESTABLISH A SAFE LEVEL:

• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound
level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:

• Do not turn up the volume so high that you can’t
hear what’s around you.
• Use caution or temporarily discontinue use in
potentially hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
S001a_A1_En

D8-10-1-3_A1_En

CAUTION:
HOT SURFACE. DO NOT TOUCH.
The top surface over the internal
heatsink may become hot when
operating this product continuously.

3

Thank you for buying this Pioneer product. Please read through these operating
instructions so you will know how to operate your model properly.

05 Basic playback
Playing a source................................................................................................................................................................42
Playing an iPod..................................................................................................................................................................43
Playing a USB device........................................................................................................................................................44
Listening to the radio.........................................................................................................................................................45
Bluetooth ADAPTER for Wireless Enjoyment of Music.................................................................................................46

Contents
01 Before you start

06 Listening to your system

Checking what’s in the box.................................................................................................................................................8
Our philosophy.....................................................................................................................................................................8
Features................................................................................................................................................................................8
Installing the receiver..........................................................................................................................................................9
Loading the batteries...........................................................................................................................................................9
Operating range of remote control unit............................................................................................................................9
About using AVNavigator (included CD-ROM)................................................................................................................9

Enjoying various types of playback using the listening modes.....................................................................................49
Selecting MCACC presets................................................................................................................................................50
Choosing the input signal.................................................................................................................................................50
Better sound using Phase Control...................................................................................................................................51

07 Playback with NETWORK features
Introduction........................................................................................................................................................................53
Playback with Network functions....................................................................................................................................54
About network playback...................................................................................................................................................55
About playable file formats...............................................................................................................................................57

02 Controls and displays
Remote control..................................................................................................................................................................12
Display................................................................................................................................................................................14
Front panel.........................................................................................................................................................................15

08 Control with HDMI function
About the Control with HDMI function............................................................................................................................59
Making Control with HDMI connections.........................................................................................................................59
HDMI Setup.......................................................................................................................................................................59
Before using synchronization...........................................................................................................................................59
About synchronized operations.......................................................................................................................................60
Setting the PQLS function................................................................................................................................................60
About Sound Retriever Link and Stream Smoother Link...............................................................................................60
Cautions on the Control with HDMI function.................................................................................................................60

03 Connecting your equipment
Connecting your equipment.............................................................................................................................................18
Rear panel..........................................................................................................................................................................18
Determining the speakers’ application...........................................................................................................................19
Placing the speakers.........................................................................................................................................................20
Connecting the speakers..................................................................................................................................................21
Installing your speaker system.........................................................................................................................................21
Selecting the Speaker system..........................................................................................................................................23
About the audio connection.............................................................................................................................................23
About the video converter.................................................................................................................................................24
About HDMI.......................................................................................................................................................................24
Connecting your TV and playback components.............................................................................................................25
Connecting an HDD/DVD recorder, BD recorder and other video sources................................................................27
Connecting a satellite/cable receiver or other set-top box............................................................................................28
Connecting other audio components..............................................................................................................................29
Connecting additional amplifiers.....................................................................................................................................30
Connecting AM/FM antennas..........................................................................................................................................30
MULTI-ZONE setup............................................................................................................................................................31
Connecting to the network through LAN interface........................................................................................................32
Connecting optional Bluetooth ADAPTER......................................................................................................................33
Connecting an iPod...........................................................................................................................................................33
Connecting a USB device.................................................................................................................................................33
Connecting an HDMI-equipped component to the front panel input..........................................................................34
Connecting to a wireless LAN..........................................................................................................................................34
Connecting an IR receiver................................................................................................................................................34
Plugging in the receiver....................................................................................................................................................35

09 Using other functions
Setting the Audio options.................................................................................................................................................62
Setting the Video options..................................................................................................................................................64
Switching the speaker terminals.....................................................................................................................................66
Using the MULTI-ZONE controls......................................................................................................................................66
Making an audio or a video recording.............................................................................................................................67
Network settings from a web browser.............................................................................................................................67
Using the sleep timer........................................................................................................................................................67
Dimming the display.........................................................................................................................................................67
Checking your system settings........................................................................................................................................67
Resetting the system.........................................................................................................................................................68

10 Controlling the rest of your system
About the Remote Setup menu.......................................................................................................................................70
Operating multiple receivers............................................................................................................................................70
Setting the remote to control other components...........................................................................................................70
Selecting preset codes directly........................................................................................................................................70
Programming signals from other remote controls........................................................................................................71
Erasing one of the remote control button settings.........................................................................................................71
Erasing all learnt settings that are in one input function..............................................................................................71
Direct function...................................................................................................................................................................72
About the ALL ZONE STBY (All Zone Standby) and DISCRETE ON (Discrete On) functions.....................................72
Resetting the remote control settings.............................................................................................................................72
Controlling components...................................................................................................................................................73

04 Basic Setup
Changing the OSD display language (OSD Language).................................................................................................37
Automatically conducting optimum sound tuning (Full Auto MCACC)......................................................................37
The Input Setup menu.......................................................................................................................................................39
Operation Mode Setup......................................................................................................................................................40
About the Home Menu.....................................................................................................................................................40

4

11 The Advanced MCACC menu
Making receiver settings from the Advanced MCACC menu.......................................................................................76
Automatic MCACC (Expert)..............................................................................................................................................76
Manual MCACC setup......................................................................................................................................................78
Checking MCACC Data.....................................................................................................................................................80
Data Management............................................................................................................................................................81

12 The System Setup and Other Setup menus
Making receiver settings from the System Setup menu...............................................................................................84
Manual speaker setup.......................................................................................................................................................84
Network Setup menu........................................................................................................................................................86
Checking the Network Information..................................................................................................................................87
The Other Setup menu......................................................................................................................................................87

13 FAQ
Troubleshooting.................................................................................................................................................................91
Power..................................................................................................................................................................................91
No sound............................................................................................................................................................................91
Other audio problems.......................................................................................................................................................92
ADAPTER PORT terminal.................................................................................................................................................93
Video...................................................................................................................................................................................93
Settings...............................................................................................................................................................................93
Professional Calibration EQ graphical output................................................................................................................94
Display................................................................................................................................................................................94
Remote control..................................................................................................................................................................94
HDMI...................................................................................................................................................................................94
AVNavigator.......................................................................................................................................................................95
USB interface.....................................................................................................................................................................96
iPod.....................................................................................................................................................................................96
Network..............................................................................................................................................................................96
Web Control.......................................................................................................................................................................97
Wireless LAN......................................................................................................................................................................98

14 Additional information
Surround sound formats................................................................................................................................................100
About iPod........................................................................................................................................................................100
About SiriusXM................................................................................................................................................................100
About FLAC......................................................................................................................................................................100
Windows 7........................................................................................................................................................................101
Auto Surround, ALC and Stream Direct with different input signal formats.............................................................101
Speaker Setting Guide....................................................................................................................................................102
About messages displayed when using network functions........................................................................................103
Important information regarding the HDMI connection.............................................................................................103
Cleaning the unit.............................................................................................................................................................103
Glossary............................................................................................................................................................................104
Features index..................................................................................................................................................................107
Specifications..................................................................................................................................................................108
Preset code list................................................................................................................................................................109

5

Flow of settings on the receiver

9	

Basic playback (page 41)

		j

10	 Adjusting the sound and picture quality as desired
!	 Using the various listening modes (page 48)
!	 Better sound using Phase Control (page 51)
!	 Measuring the all EQ type (SYMMETRY/ALL CH ADJ/FRONT ALIGN) (page 76)
!	 Changing the channel level while listening (page 85)
!	 Switching on/off the Acoustic Calibration EQ, Auto Sound Retriever or Dialog Enhancement (page 62)
!	 Setting the PQLS function (page 60)
!	 Setting the Audio options (page 62)
!	 Setting the Video options (page 64)
		j

Flow for connecting and setting the receiver
The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used easily after following the procedure below to make the connections and settings.
Required setting item: 1, 2, 3, 4, 5, 7, 9
Setting to be made as necessary: 6, 8, 10, 11, 12

Important
The receiver’s initial settings can be made on the computer using Wiring Navi on the AVNavigator CD-ROM
included with the receiver. In this case, virtually the same connections and settings as in steps 2, 3, 4, 5, 6, 7
and 8 can be made interactively. For instructions on using AVNavigator, see About using AVNavigator (included
CD-ROM) on page 9.

1	

11	 Other optional adjustments and settings
!	 Control with HDMI function (page 58)
!	 The Advanced MCACC menu (page 75)
!	 The System Setup and Other Setup menus (page 83)
		j

Before you start

!	 Checking what’s in the box on page 8
!	 Loading the batteries on page 9
		j

2	

12	 Making maximum use of the remote control
!	 Operating multiple receivers (page 70)
!	 Setting the remote to control other components (page 70)

Determining the speakers’ application (page 19)

!	 7.2 channel surround system (Front height)
!	 7.2 channel surround system (Front wide)
!	 7.2 channel surround system & Speaker B connection
!	 5.2 channel surround system & Front Bi-amping connection (High quality surround)
!	 5.2 channel surround system & ZONE 2 connection (Multi Zone)
		j

3	

Connecting the speakers

!	 Placing the speakers on page 20
!	 Connecting the speakers on page 21
!	 Installing your speaker system on page 21
!	 Bi-amping your speakers on page 22
		j

4	

Connecting the components

!	 About the audio connection on page 23
!	 About the video converter on page 24
!	 Connecting your TV and playback components on page 25
!	 Connecting AM/FM antennas on page 30
!	 Plugging in the receiver on page 35
		j

5	

Power On

		j

6	

Changing the OSD display language (OSD Language) (page 37)

		j

7	

MCACC speaker settings

!	 Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37
		j

8	

The Input Setup menu (page 39)

(When using connections other than the recommended connections)
		j

6

Before you start
Checking what’s in the box............................................................................................................. 8
Our philosophy................................................................................................................................. 8
Features............................................................................................................................................. 8
Installing the receiver....................................................................................................................... 9
Loading the batteries....................................................................................................................... 9
Operating range of remote control unit......................................................................................... 9
About using AVNavigator (included CD-ROM).............................................................................. 9

7

　
　
　
　

01

Before you start

%	 HDMI (3D, Audio Return Channel)

Checking what’s in the box

A compatible component is required to use the above function.

Please check that you’ve received the following supplied accessories:
!	 Setup microphone (cable: 5 m (16.4 ft.))
!	 Remote control unit
!	 AAA size IEC R03 dry cell batteries (to confirm system operation) x2
!	 AM loop antenna
!	 FM wire antenna
!	 iPod cable
!	 Power cord
!	 CD-ROM (AVNavigator)
!	 Quick start guide
!	 Safety Brochure
!	 Warranty sheet

%	 PQLS Bit-stream
Jitterless high quality playback is possible by connecting a PQLS-compatible player with HDMI connections.
This feature is only available when the connected Pioneer Blu-ray Disc Player supporting the PQLS function.

%	 Auto Phase Control Plus
For discs created with standards other than Phase Control, the LFE channel is delayed upon recording in the first
place. This function automatically corrects for phase shifting on such discs and broadcast.
This function is especially effective when playing music.

%	 Hi-bit 24
Creates a wider dynamic range with digital sources like CDs, DVDs or BDs. 16- and 20-bit PCM as well as compressed audio is requantized to 24 bits, and the high frequency component is interpolated upon data processing
to enable smoother, more subtle musical expression.

%	 Sound Retriever Link
By connecting a Pioneer player supporting the Sound Retriever Link function, compressed audio files played on
the player can be corrected automatically to play the sound with higher density.
This feature is only available when the connected Pioneer Blu-ray Disc Player supporting the PQLS function.

Our philosophy
Pioneer is dedicated to making your home theater listening experience as close as possible to the vision of the
moviemakers and mastering engineer when they created the original soundtrack. We do this by focusing on three
important steps:

%	 Virtual Wide speaker

1	 Designing with carefully selected components so as to transmit the original soundtrack
accurately

When you’re not using front wide speakers, selecting this mode allows you to hear a virtual front wide channel
through your front speakers.
This improves the continuity of the sound from the front channel to the surround channels.

2	

Allowing for customized acoustic calibration according to any listening area

%	 Stream Smoother Link

3	

Tuning that transmits soul

By connecting a Pioneer player supporting the Stream Smoother Link function, compressed video or movie files
played on the player can be corrected automatically to play them with a more natural, easily viewable picture.
This feature is only available when the connected Pioneer Blu-ray Disc Player supporting the PQLS function.

Features

%	 iPod playback
Your iPod, iPhone or iPad can be connected to the receiver’s USB terminal and RCA video terminal to play the
music/video files on the iPod, iPhone or iPad.
Also, the iPod, iPhone or iPad is charged when it is connected to the receiver.

%	 Class D Amplifier
This unit is an AV receiver developed based on the latest high performance Class D amplifier and integrating
the essence of Pioneer’s high sound quality designs. This new generation reference amplifier offers outstanding
performance with high sound quality and reproduces the latest in multi-channel digital contents.

%	 Dolby Pro Logic llz compatible
Adding a pair of speakers above the front left and right speakers adds expressiveness in the vertical direction to
the previous horizontally-oriented sound field. The height channel strengthens the sound field’s sense of threedimensionality and air, producing presence and expansion.

%	 Apple AirPlay®
With AirPlay you can stream music from iTunes to the SC-1222 and play it through your home theater system.
You can even use the receiver to view metadata including song title, artist as well as album art on a connected
display. With Pioneer’s Air­Play-compatible receivers, you can easily enjoy your iTunes music in any room in the
house.

%	 Internet Radio
By connecting this receiver to the network via the LAN terminal, you can listen to Internet radio stations.

%	 Bluetooth compatible

%	 Air Jam App compatible

Using the Bluetooth ADAPTER (AS-BT100 or AS-BT200) lets you enjoy music files on an iPhone or other Bluetooth
wireless technology device wirelessly.

For the SC-1222, the optional AS-BT200 Bluetooth adapter works together with Pioneer’s exclusive Air Jam application. Available free App in App Store and Android Market, Air Jam allows up to 4 iPhone, iPod touch, iPad or
Android devices to share music and create a group playlist for a unique and fun social music network experience.

%	 Auto Sound Retriever
The Auto Sound Retriever feature employs DSP technology to restore sound pressure and smooth jagged artifacts left over after compression.

%	AVNavigator
The CD-ROM (AVNavigator) included with this unit provides a variety of functions, such as Wiring Navi with a
guide for connecting the unit and setting up from the computer and an Interactive Manual for operating the
unit while reading the manual.
Also, Operation Guide describes the receiver’s playback operations and how to use several functions through
videos and illustrations.
AVNavigator is not only included PC software, but also iPad version in free download from App Store. For detail,
check the website: http://pioneer.jp/product/soft/iapp_avnavi/en.html

%	 Easy setup using Advanced MCACC
The Auto MCACC Setup provides a quick but accurate surround sound setup, which includes the advanced features of Professional Acoustic Calibration EQ.

8

　
　
　
　

01

Before you start

Installing the receiver
!	 When installing this unit, make sure to put it on a level and stable surface.
!	 Don’t install it on the following places:
—	on a color TV (the screen may distort)
—	near a cassette deck (or close to a device that gives off a magnetic field). This may interfere with the sound.
—	in direct sunlight
—	in damp or wet areas
—	in extremely hot or cold areas
—	in places where there is vibration or other movement
—	in places that are very dusty
—	in places that have hot fumes or oils (such as a kitchen)
!	 Do not touch this receiver’s bottom panel while the power is on or just after it is turned off. The bottom panel
becomes hot when the power is on (or right after it is turned off) and could cause burns.

30°
30°

7 m (23 ft.)

About using AVNavigator (included CD-ROM)
The included AVNavigator CD-ROM contains Wiring Navi allowing you to easily make the receiver’s connections
and initial settings in dialog fashion. High precision initial settings can be completed easily simply by following
the instructions on the screen to make the connections and settings.
There are also other features enabling easy use of various functions, including an Interactive Manual that operates in association with the receiver, updating of various types of software, and MCACC Application that lets you
check the MCACC measurement results on 3D graphs.

Loading the batteries
The batteries included with the unit are to check initial operations; they may not last over a long period. We recommend using alkaline batteries that have a longer life.

Installing AVNavigator
1	

Load the included CD-ROM into your computer’s CD drive.

The CD-ROM’s top menu screen appears.

WARNING

2	

Click ‘Install AVNavigator’ from the CD-ROM top menu.

3	

Follow the instructions on the screen to install.

When “Finish” is selected, installation is completed.

!	 Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.

4	

Remove the included CD-ROM from the computer’s CD drive.

Handling the CD-ROM
CAUTION

Operating Environment

Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:
!	 Never use new and old batteries together.
!	 Insert the plus and minus sides of the batteries properly according to the marks in the battery case.
!	 Batteries with the same shape may have different voltages. Do not use different batteries together.
!	 When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/area.

!	 AVNavigator can be used with Microsoft® Windows® XP/Vista/7.
!	 A browser is at times used for AVNavigator functions. The supported browser is Microsoft Internet Explorer 8
or 9.
!	Adobe® Flash® Player 10 must be installed to use some of the functions in AVNavigator.
	 For details, see http://www.adobe.com/downloads/.

Operating range of remote control unit

!	 This CD-ROM is for use with a personal computer. It cannot be used with a DVD player or music CD player.
Attempting to play this CD-ROM with a DVD player or music CD player can damage speakers or cause
impaired hearing due to the large volume.

Precautions For Use

The remote control may not work properly if:
!	 There are obstacles between the remote control and the receiver’s remote sensor.
!	 Direct sunlight or fluorescent light is shining onto the remote sensor.
!	 The receiver is located near a device that is emitting infrared rays.
!	 The receiver is operated simultaneously with another infrared remote control unit.

License
!	 Please agree to the “Terms of Use” indicated below before using this CD-ROM. Do not use if you are unwilling
to consent to the terms of its use.

9

　
　
　
　

01

Before you start

　
　
　
　

Terms of Use
!	 Copyright to data provided on this CD-ROM belongs to PIONEER CORPORATION. Unauthorized transfer,
duplication, broadcast, public transmission, translation, sales, lending or other such matters that go beyond
the scope of “personal use” or “citation” as defined by Copyright Law may be subject to punitive actions.
Permission to use this CD-ROM is granted under license by PIONEER CORPORATION.

General Disclaimer
!	 PIONEER CORPORATION does not guarantee the operation of this CD-ROM with respect to personal computers using any of the applicable OS. In addition, PIONEER CORPORATION is not liable for any damages
incurred as a result of use of this CD-ROM and is not responsible for any compensation. The names of private
corporations, products and other entities described herein are the registered trademarks or trademarks of their
respective firms.

Using AVNavigator
1	

Click [AVNavigator 2012.II] on the desktop to launch AVNavigator.

AVNavigator is launched and Wiring Navi starts up. The language selection screen appears. Follow the instructions on the screen to make the connections and automatic settings.
Wiring Navi only starts up automatically the first time AVNavigator is launched.

2	

Select and use the desired function.

AVNavigator includes the following functions:
!	 Wiring Navi – Guides you through connections and initial settings in dialog fashion. High precision initial
settings can be made easily.
!	 Operation Guide – Describes the receiver’s playback operations and how to use several functions through
videos and illustrations.
!	 Interactive Manual – Automatically displays the pages explaining the functions that have been operated on
the receiver. It is also possible to operate the receiver from the Interactive Manual.
!	 Glossary – Displays glossary pages.
!	 MCACC Appli – Displays Advanced MCACC measurement results vividly on the computer.
	 There are special operating instructions for MCACC Application. These instructions are included in the
AVNavigator Interactive Manual’s menus. Refer to them when using MCACC Application.
!	 Software Update – Allows various types of software to be updated.
!	 Settings – Used to make various AVNavigator settings.
!	 Detection – Used to detect the receiver.

Deleting the AVNavigator
You can use the following method to uninstall (delete) the AVNavigator from your PC.

%	 Delete from the Control Panel of the PC.

From the Start menu, click “Program” d “PIONEER CORPORATION” d “AVNavigator 2012.II” d “Uninstall
AVNavigator 2012.II”.

10

Controls and displays
Remote control............................................................................................................................... 12
Display.............................................................................................................................................14
Front panel...................................................................................................................................... 15

11

　
　
　
　

02

Controls and displays

The remote has been conveniently color-coded according to component control using the following system:
!	 White – Receiver control, TV control
!	 Blue – Other controls (See pages 43, 44, 45, 46 and 73.)

Remote control
This section explains how to operate the remote control for the receiver.

1	

1
2,3

RECEIVER ALL ZONE STBY
DISCRETE ON

DVD

DVR

3	

HDMI

TV

CD

NET

USB

CBL

OPTION 1

iPod

SAT

ADPT

TUNER
STATUS

5

RECEIVER

VOL

MUTE

AUDIO
PARAMETER

13

5	

TOP MENU

15

TOOLS
MENU
ENTER

HOME
MENU

RETURN

6	

iPod CTRL

PQLS

Hi-Bit

BAND

MPX

D.FILT
PTY

PRESET

7	

TUNE

1

5

2

4

5

SPEAKERS DIMMER

7

8

3

AUDIO

AUTO
CH LEVEL S.RTRV

6

DISP

SLEEP

9

8	

CH

D.ACCESS HDMI OUT CLASS

0

ENTER

ZONE 2

ZONE 3

ZONE 4

Z2

Z3

Z4

/ CLR

10

TV CONTROL buttons

Receiver setting buttons

Press
first to access:
!	 AUDIO PARAMETER – Use to access the Audio options (page 62).
!	 VIDEO PARAMETER – Use to access the Video options (page 64).
!	 HOME MENU – Use to access the Home Menu (pages 37, 39, 59, 76 and 84).
!	 RETURN – Press to confirm and exit the current menu screen.

AUTO/ALC/
DIRECT STANDARD ADV SURR +Favorite

SIGNAL SEL MCACC

Receiver Control buttons

These buttons can be used to perform operations on the TV to which the TV CONTROL INPUT button is assigned.
The TV can be operated with these buttons regardless of the input set for the remote control’s operation mode
(page 70).

FEATURES
PHASE

Input function buttons

Press
first to access:
!	 STATUS – Press to check selected receiver settings (page 67).
!	 AUTO/ALC/DIRECT – Switches between Auto Surround (page 49), Auto Level Control mode and Stream
Direct mode (page 50).
!	 STANDARD – Press for Standard decoding and to switch various modes (2 Pro Logic, Neo:6, etc.) (page 49).
!	 ADV SURR – Use to switch between the various surround modes (page 49).
!	 SIGNAL SEL – Use to select an input signal (page 50).
!	 MCACC – Press to switch between MCACC presets (page 50).
!	 CH LEVEL – Press repeatedly to select a channel, then use k/l to adjust the level (page 85).
!	 AUTO S.RTRV – Press to restore CD quality sound to compressed audio sources (page 62).
!	 SPEAKERS – Use to change the speaker terminal (page 66).
!	 DIMMER – Dims or brightens the display (page 67).
!	 SLEEP – Use to put the receiver in sleep mode and select the amount of time before sleep (page 67).

VIDEO
PARAMETER

8

9

RCU SETUP

Press to select control of other components (page 70).
Use INPUT SELECT c/ d to select the input function (page 42).

14

TV CONTROL

CH

4	

12

VOLUME

INPUT

7

ALL ZONE STBY DISCRETE ON

Use this button to perform unique operations (page 72).
Use to input the preset code when making remote control settings and to set the remote control mode (page 70).

INPUT SELECT

6

2	

11

BDR
BD

4

This switches between standby and on for this receiver.

SOURCE

RCU SETUP

u RECEIVER

i/j/k/l/ENTER

Use the arrow buttons when setting up your surround sound system (see page 76) and the Audio or Video options
(page 62 or 64).

CH
OPTION 2

9	

FEATURES buttons

These let you operate the receiver’s features directly.
!	 PHASE – Press to switch on/off Phase Control (page 51).
!	 PQLS – Press to select the PQLS setting (page 60).
!	 Hi-Bit – Press to switch on/off the Hi-Bit 24 setting (page 62).
!	 D.FILT – With this receiver, D.FILT cannot be used.

RECEIVER

10	 MULTI-ZONE select buttons
Switch to perform operations in ZONE 2 and ZONE 3 (page 66).

12

　
　
　
　

02

Controls and displays

　
　
　
　

11	 Remote control LED
Lights when a command is sent from the remote control.

12	OPTION
The preset codes of desired devices can be registered in the remote control and button operations can be registered using the learning mode.

13	
Switches the remote to control the receiver (used to select the white commands).
Switch to perform operations in the main zone.
Also use this button to set up surround sound.

14	 VOLUME +/–
Use to set the listening volume.

15	MUTE
Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound).

Note
!	 With this receiver, HDMI OUT, D.FILT, OPTION 2 and ZONE 4 buttons cannot be used.

13

02

Controls and displays

8	

Display
1
AUTO

HDMI
DIGITAL
ANALOG

2
L
SL
XL

3

C
XC
LFE

45 6

7 8

9

10

11

12

13

DSD PCM
TUNED
R 2DIGITAL PLUS
2TrueHD
MULTI-ZONE
PQLS ALC
ATT STEREO
SR DTS HD ES 96/24 S.RTRV SOUND UP MIX OVER MONO
XR
MSTR

CD

TUNER

AUTO SURROUND
STREAM DIRECT

iPod

DVD TV
BD DVR

VIDEO
HDMI

14 15

dB

9	

USB
[2] [3] [4]

10	 Analog signal indicators
Light to indicate reducing the level of an analog signal (page 62).

ADV.SURROUND
STANDARD
SP AB
SLEEP

1	

16

17

18

(PHASE CONTROL)

Lights when the Phase Control is switched on (page 51).

2PROLOGIC x Neo:6

8

Listening mode indicators

!	 AUTO SURROUND – Lights when the Auto Surround feature is switched on (page 49).
!	 ALC – Lights when the ALC (Auto level control) mode is selected (page 49).
!	 STREAM DIRECT – Lights when Direct/Pure Direct is selected (page 50).
!	 ADV.SURROUND – Lights when one of the Advanced Surround modes has been selected (page 49).
!	 STANDARD – Lights when one of the Standard Surround modes is switched on (page 49).

11	 Tuner indicators
19

!	 TUNED – Lights when a broadcast is being received.
!	 STEREO – Lights when a stereo FM broadcast is being received in auto stereo mode.
!	 MONO – Lights when the mono mode is set using MPX.

20

Signal indicators

Light to indicate the currently selected input signal. AUTO lights when the receiver is set to select the input signal automatically (page 50).

12	

2	

13	 Master volume level

Lights when the sound is muted.

Program format indicators

Light to indicate the channels to which digital signals are being input.
!	 L/R – Left front/Right front channel
!	 C – Center channel
!	 SL/SR – Left surround/Right surround channel
!	 LFE – Low frequency effects channel (the (( )) indicators light when an LFE signal is being input)
!	 XL/XR – Two channels other than the ones above
!	 XC – Either one channel other than the ones above, the mono surround channel or matrix encode flag

3	

Shows the overall volume level.
“---” indicates the minimum level, and “+12dB” indicates the maximum level.

14	 Input function indicators
Light to indicate the input function you have selected.

15	 Scroll indicators
Light when there are more selectable items when making the various settings.

Digital format indicators

16	 Speaker indicators

Light when a signal encoded in the corresponding format is detected.
!	 2 DIGITAL – Lights with Dolby Digital decoding.
!	 2 DIGITAL PLUS – Lights with Dolby Digital Plus decoding.
!	 2 TrueHD – Lights with Dolby TrueHD decoding.
!	 DTS – Lights with DTS decoding.
!	 DTS HD – Lights with DTS-HD decoding.
!	 96/24 – Lights with DTS 96/24 decoding.
!	 DSD PCM – Light during DSD (Direct Stream Digital) to PCM conversion with SACDs.
!	 PCM – Lights during playback of PCM signals.
!	 MSTR – Lights during playback of DTS-HD Master Audio signals.

Lights to indicate the current speaker system using SPEAKERS (page 66).

17	SLEEP
Lights when the receiver is in sleep mode (page 67).

18	 Matrix decoding format indicators
!	 2PRO LOGIC IIx – This lights to indicate 2 Pro Logic II / 2 Pro Logic IIx decoding (page 49).
!	 Neo:6 – When one of the Neo:6 modes of the receiver is on, this lights to indicate Neo:6 processing (page 49).

19	 Character display
Displays various system information.

20	 Remote control mode indicator

4	MULTI-ZONE

Lights to indicate the receiver’s remote control mode setting. (Not displayed when set to 1.) (page 88)

Lights when the MULTI-ZONE feature is active (page 66).

5	SOUND
Lights when the DIALOG E (Dialog Enhancement) or TONE (tone controls) features is selected (page 62).

6	PQLS
Lights when the PQLS feature is active (page 60).

7	S.RTRV
Lights when the Auto Sound Retriever function is active (page 62).

14

　
　
　
　

02

Controls and displays

Front panel
1

2

3

4

3

5

6	

MASTER VOLUME dial

7	

Front panel controls

To access the front panel controls, catch the sides of the door with your fingers and pull forward.

6

INPU
SELET
CTOR

ADVANCED
MCACC

STAN
DBY

FL OFF

HDMI

/ON

iPod iPhone iPad

MAST
VOLU ER
ME

INPUT
SELECTOR

MASTER
VOLUME

8	

AUDIO PARAMETER

Use to access the Audio options (page 62).

STANDBY/ON

9	

i/j/k/l (TUNE/PRESET) /ENTER

Use the arrow buttons when setting up your Home Menu. Use TUNE i/j to find radio frequencies and use
PRESET k/l to find preset stations (page 45).

10	 VIDEO PARAMETER
Use to access the Video options (page 64).

8

9 10
AUDIO
PARAMETER

7

TUNE

11

VIDEO
PARAMETER

12

MULTI-ZONE
ON/OFF
CONTROL

ENTER

13
iPod iPhone iPad
DIRECT CONTROL

SPEAKERS

AUTO SURR/ALC/
STREAM DIRECT

STEREO

11	 MULTI-ZONE controls

STANDARD
SURROUND

If you’ve made MULTI-ZONE connections (page 31) use these controls to control the sub zone from the main zone
(page 66).

ADVANCED
SURROUND

12	SPEAKERS
Use to change the speaker terminal (page 66).

BAND

PRESET

13	 iPod iPhone iPad DIRECT CONTROL

PRESET
PHONES

HOME MENU

RETURN

TUNER EDIT

MCACC
SETUP MIC

TUNE

15
1	

14

5V

USB
2.1 A

Change the receiver’s input to the iPod and enable iPod operations on the iPod (page 43).

HDMI 5 INPUT

14	 Listening mode buttons

iPod iPhone iPad

16

17

18

19

20

!	 AUTO SURR/ALC/STREAM DIRECT – Switches between Auto Surround (page 49), Auto Level Control and
Stream Direct mode (page 50).
!	 STEREO – Press to select stereo playback mode (page 49).
!	 STANDARD SURROUND – Press for Standard decoding and to switch various modes (2 Pro Logic, Neo:6,
Stereo etc.) (page 49).
!	 ADVANCED SURROUND – Use to switch between the various surround modes (page 49).

21

u STANDBY/ON

This switches between standby and on for this receiver.

2	

15	 HOME MENU

INPUT SELECTOR dial

Use to select an input function.

Use to access the Home Menu (pages 37, 39, 59, 76 and 84).

3	Indicators

16	RETURN
Press to confirm and exit the current menu screen.

!	 ADVANCED MCACC – Lights when EQ is set to ON in the AUDIO PARAMETER menu (page 62).
!	 FL OFF – Lights when “off” (nothing displayed) is selected with the display’s dimmer adjustment (page 67).
!	 HDMI – Blinks when connecting an HDMI-equipped component; lights when the component is connected
(page 25).
!	 iPod iPhone iPad – Lights to indicate iPod/iPhone/iPad is connected (page 33).

4	

17	 TUNER controls
!	 BAND – Switches between AM and FM radio bands (page 45).
!	 TUNER EDIT – Use with TUNE i/j, PRESET k/l and ENTER to memorize and name stations for recall
(page 45).

Character display

18	 PHONES jack

See Display on page 14.

5	

Use to connect headphones. When the headphones are connected, there is no sound output from the speakers.

Remote sensor

19	 MCACC SETUP MIC jack

Receives the signals from the remote control (page 9).

Use to connect the supplied microphone (page 37).

15

　
　
　
　

02

Controls and displays

　
　
　
　

20	 iPod iPhone iPad USB terminals
Use to connect your Apple iPod/iPhone/iPad as an audio and video source (page 33), or connect a USB device for
audio and photo playback (page 33).

21	 HDMI input connector
Use for connection to a compatible HDMI device (Video camera, etc.) (page 34).

16

Connecting your equipment
Connecting your equipment.......................................................................................................... 18
Rear panel....................................................................................................................................... 18
Determining the speakers’ application......................................................................................... 19
Placing the speakers....................................................................................................................... 20
Connecting the speakers................................................................................................................ 21
Installing your speaker system...................................................................................................... 21
Selecting the Speaker system........................................................................................................ 23
About the audio connection.......................................................................................................... 23
About the video converter............................................................................................................ 24
About HDMI.................................................................................................................................... 24
Connecting your TV and playback components.......................................................................... 25
Connecting an HDD/DVD recorder, BD recorder and other video sources................................ 27
Connecting a satellite/cable receiver or other set-top box......................................................... 28
Connecting other audio components........................................................................................... 29
Connecting additional amplifiers.................................................................................................. 30
Connecting AM/FM antennas........................................................................................................ 30
MULTI-ZONE setup......................................................................................................................... 31
Connecting to the network through LAN interface.................................................................... 32
Connecting optional Bluetooth ADAPTER.................................................................................... 33
Connecting an iPod........................................................................................................................ 33
Connecting a USB device............................................................................................................... 33
Connecting an HDMI-equipped component to the front panel input....................................... 34
Connecting to a wireless LAN........................................................................................................ 34
Connecting an IR receiver.............................................................................................................. 34
Plugging in the receiver................................................................................................................. 35

17

　
　
　
　

03

Connecting your equipment

Connecting your equipment

Note
!	 The input functions below are assigned by default to the receiver’s different input terminals. Refer to The Input
Setup menu on page 39 to change the assignments if other connections are used.

This receiver provides you with many connection possibilities, but it doesn’t have to be difficult. This chapter
explains the kinds of components you can connect to make up your home theater system.

!	 Before making or changing the connections, switch off the power and disconnect the power cord from the
power outlet. Plugging in should be the final step.
!	 When making connections, also keep the power cords of the devices being connected unplugged from the
power outlets.
!	 Depending on the device being connected (amplifier, receiver, etc.), the methods of connection and terminal
names may differ from the explanations in this manual. Also refer to the operating instructions of the respective devices.

Rear panel
IN 1
(DVD)

HDMI

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

(OUTPUT 5 V
0.6 A MAX)

ASSIGNABLE
1 -6
ASSIGNABLE

LAN (10/100)

COMPONENT VIDEO

Y

PB

PR

VIDEO

IN 1
(DVD)

MONITOR
OUT

AC IN

IN 1
(TV)

DC OUTPUT

for WIRELESS LAN

IN 2

(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 2
(DVR/
BDR)

ZONE 2 ZONE 3
OUT
OUT

DVD
IN

SAT/CBL VIDEO
IN
IN

DVR/BDR
OUT
IN

IN 1 (CD)

FRONT

ASSIGNABLE

1

SUBWOOFER

IN 1

(DVD)

IN 2

(SAT/CBL)

PRE OUT

(OUTPUT 5 V
0.1 A MAX)

R

ANTENNA

AM LOOP

R

FRONT

L

CENTER

CENTER

FRONT HEIGHT / FRONT WIDE /

R

B

L

R

Audio

Component

IN 1

COAX-1

IN 1

BD

(BD)

DVD
SAT/CBL

IN 2

COAX-2

DVR/BDR

IN 3

OPT-2

VIDEO

IN 4

HDMI 5
(front panel)

IN 5

HDMI 6

IN 6

TV

OPT-1

CD

ANALOG-1

SURROUND BACK

L

(Single)

R

SURROUND

MONITOR
OUT

A

L

RS-232C

FM UNBAL 75

SUBWOOFER

ANTENNA

SPEAKERS
IR
OUT

EXTENSION

IN 2

!	 The CU-RF100 omni-directional remote control (separately sold) can be connected to the RS-232C and
EXTENSION terminals. Using the CU-RF100 lets you display the receiver’s display information on the remote
control display in your hands and operate it without worrying about obstacles or the direction in which the
remote control is pointing.

ADAPTER PORT

L

AUDIO

A

SUBWOOFER

HDMI

COAXIAL ASSIGNABLE

SURROUND SURR BACK FH / FW
(Single)

2

MONITOR
OUT

RS-232C

Input Terminals

Input function

CAUTION

IN

AM LOOP

FM UNBAL 75

IR

(OUTPUT 5 V
150 mA MAX)

OUT

EXTENSION

18

(OUTPUT 5 V
150 mA MAX)

IN

　
　
　
　

03

Connecting your equipment

[B] 7.2 channel surround system (Front wide)

Determining the speakers’ application

!	 Speaker System setting: Normal(SB/FW)

This unit permits you to build various surround systems, in accordance with the number of speakers you have.
!	 Be sure to connect speakers to the front left and right channels (L and R).
!	 It is also possible to only connect one of the surround back speakers (SB) or neither.
!	 If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal.
Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this
case, the same sound is output from the two subwoofers.
Choose one from Plans [A] to [E] below.

R
FWR

L

C

SW 2

Important

SW 1

SR

FWL

!	The Speaker System setting must be made if you use any of the connections shown below other than [A] (see
Speaker system setting on page 84).
!	 Sound does not come through simultaneously from the front height, front wide, speaker B and surround back
speakers. Output speakers are different depending on the input signal or listening mode.

*Default setting
!	 Speaker System setting: Normal(SB/FH)
FHR

SW 2

SL

[C] 7.2 channel surround system & Speaker B connection
!	 Speaker System setting: Speaker B

R

L
C

SW 1

SBL

This plan replaces the left and right front height speakers shown in [A] with the left and right front wide speakers
(FWL/FWR).
It is not possible to produce sound simultaneously from the front wide speakers and the surround back speakers.
This surround system provides a sound field with good association between the sounds of the different channels.

[A] 7.2 channel surround system (Front height)

FHL

SBR

SL

SR
R
L

SBR
SBL

SW 2

A 7.2 ch surround system connects the left and right front speakers (L/R), the center speaker (C), the left and right
front height speakers (FHL/FHR), the left and right surround speakers (SL/SR), the left and right surround back
speakers (SBL/SBR), and the subwoofers (SW 1/SW 2).
It is not possible to produce sound simultaneously from the front height speakers and the surround back
speakers.
This surround system produces a more true-to-life sound from above.

SL

C

SW 1

R
SR

L

SBR
SBL

Speaker B

With these connections you can simultaneously enjoy 5.2-channel surround sound in the main zone with stereo
playback of the same sound on the B speakers. The same connections also allow for 7.2-channel surround sound
in the main zone when not using the B speakers.

19

　
　
　
　

03

Connecting your equipment

[D] 5.2 channel surround system & Front Bi-amping connection (High quality
surround)

Placing the speakers
Refer to the chart below for placement of the speakers you intend to connect.

!	 Speaker System setting: Front Bi-Amp
Bi-amping connection of the front speakers for high sound quality with 5.2-channel surround sound.
Front Bi-Amp

L

SW 2

C

SL
SR

!	 Speaker System setting: ZONE 2
With these connections you can simultaneously enjoy 5.2-channel surround sound in the main zone with stereo
playback on another component in ZONE 2. (The selection of input devices is limited.)

120
SR

60
SB

SBR

Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines
should help you to get the best sound from your system.
!	 The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re
listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a
wall is not recommended.
!	 For the best stereo effect, place the front speakers 2 m to 3 m (6 ft. to 9 ft.) apart, at equal distance from the TV.
!	 If you’re going to place speakers around your CRT TV, use shielded speakers or place the speakers at a sufficient distance from your CRT TV.
!	 If you’re using a center speaker, place the front speakers at a wider angle. If not, place them at a narrower
angle.
!	 Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV
screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left
and right speakers.
!	 It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use
less of an angle for bigger rooms.
!	 Surround and surround back speakers should be positioned 60 cm to 90 cm (2 ft. to 3 ft.) higher than your
ears and tilted slightly downward. Make sure the speakers don’t face each other. For DVD-Audio, the speakers
should be more directly behind the listener than for home theater playback.
!	 Try not to place the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.

R

ZONE 2
Sub zone
SW 1

R
SR

FWR

Some tips for improving sound quality

Main zone

C

60

!	 Place the surround speakers at 120º from the center. If you, (1) use the surround back speaker, and, (2) don’t
use the front height speakers / front wide speakers, we recommend placing the surround speaker right beside
you.
!	 If you intend to connect only one surround back speaker, place it directly behind you.
!	 Place the left and right front height speakers at least one meter (3.3 ft.) directly above the left and right front
speakers.

[E] 5.2 channel surround system & ZONE 2 connection (Multi Zone)

SW 2

30

120

SBL

SL

L

30
60

SW 1

FHR
R

FWL

R
L

SW 2 SW 1
C

FHL

L

SL

Other speaker connections
!	 Your favorite speaker connections can be selected even if you have fewer than 5.2 speakers (except front left/
right speakers).
!	 When not connecting a subwoofer, connect speakers with low frequency reproduction capabilities to the front
channel. (The subwoofer’s low frequency component is played from the front speakers, so the speakers could
be damaged.)
!	 After connecting, be sure to conduct the Full Auto MCACC (speaker environment setting) procedure. See
Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37.

20

　
　
　
　

03

Connecting your equipment

Connecting the speakers

Installing your speaker system

Each speaker connection on the receiver comprises a positive (+) and negative (–) terminal. Make sure to match
these up with the terminals on the speakers themselves.
This unit supports speakers with a nominal impedance of 4 W to 16 W.

At the very least, front left and right speakers only are necessary. Note that your main surround speakers should
always be connected as a pair, but you can connect just one surround back speaker if you like (it must be connected to the left surround back terminal).

Standard surround connection

CAUTION
!	 These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated
parts.
!	 Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any
of the bare speaker wire touches the back panel it may cause the power to cut off as a safety measure.

The front height terminals can also be used for the front wide and Speaker B speakers.
Front height setting
Front height right

Front height left
Front wide setting

Front wide right

Bare wire connections

Front wide left
Speaker B setting

Speaker B - right

Speaker B - left

CAUTION
Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk
of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as
earthquakes.

1	

Twist exposed wire strands together.

2	

Loosen terminal and insert exposed wire.

3	

Tighten terminal.

1

2

Front right

Subwoofer 1

Center

Subwoofer 2

LINE LEVEL
INPUT

3
FRONT

1

SUBWOOFER

LINE LEVEL
INPUT

FRONT

PRE OUT

SURROUND SURR BACK FH / FW
(Single)

2

Front left

L

1

SUBWOOFER

PRE OUT

SURROUND SURR BACK FH / FW
(Single)

2

R

10 mm (3/8 in.)

L

CENTER

A

R

FRONT

L

CENTER

FRONT HEIGHT / FRONT WIDE /

R

B

L

R

SURROUND BACK

L

(Single)

R

SURROUND

A

L

SPEAKERS

R
CENTER

A

R

Note

FRONT

L

CENTER

FRONT HEIGHT / FRONT WIDE /

R

B

L

R

SURROUND BACK

L

(Single)

R

SURROUND

A

L

SPEAKERS

!	 Please refer to the manual that came with your speakers for details on how to connect the other end of the
speaker cables to your speakers.
!	 Use an RCA cable to connect the subwoofer. It is not possible to connect using speaker cables.
!	 If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal.
Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this
case, the same sound is output from the two subwoofers.

The surround back terminals can also be used for ZONE 2.

Banana plug connections

5.2 ch surround setting
Not connected

If you want to use speaker cables terminated with banana plugs, screw the speaker terminal fully shut, then plug
the banana plug into the end of the speaker terminal.

Not connected
6.2 ch surround setting

Not connected

Surround back
7.2 ch surround setting

Surround right

Surround back right

Surround left

Surround back left
ZONE 2 setting

ZONE 2 - Right

21

ZONE 2 - Left

　
　
　
　

03

Connecting your equipment

Bi-amping your speakers

Bi-wiring your speakers

Bi-amping is when you connect the high frequency driver and low frequency driver of your speakers to different
amplifiers for better crossover performance. Your speakers must be bi-ampable to do this (having separate terminals for high and low) and the sound improvement will depend on the kind of speakers you’re using.

Your speakers can also be bi-wired if they support bi-amping.
!	 With these connections, the Speaker System setting makes no difference.

Front right

CAUTION

Front left
Bi-amp compatible
speaker

High

Bi-amp compatible
speaker

!	 Don’t connect different speakers from the same terminal in this way.
!	 When bi-wiring as well, heed the cautions for bi-amping shown above.

High

%	 To bi-wire a speaker, connect two speaker cords to the speaker terminal on the receiver.
Using a banana plug for the second connection is recommended.

Low

Low

Subwoofer 1

Center

Subwoofer 2

LINE LEVEL
INPUT

LINE LEVEL
INPUT

FRONT

PRE OUT

SUBWOOFER

1

SURROUND SURR BACK FH / FW
(Single)

2

L
R
CENTER

A

R

FRONT

L

CENTER

B

FRONT HEIGHT / FRONT WIDE /

R

L

R

SURROUND BACK

L

(Single)

R

SURROUND

A

L

SPEAKERS

FRONT

1

SUBWOOFER

PRE OUT

SURROUND SURR BACK FH / FW
(Single)

2

L
R
CENTER

A

R

FRONT

L

CENTER

FRONT HEIGHT / FRONT WIDE /

R

B

L

R

SURROUND BACK

L

(Single)

R

SURROUND

A

L

SPEAKERS

Surround right

Surround left

CAUTION
!	 Most speakers with both High and Low terminals have two metal plates that connect the High to the Low
terminals. These must be removed when you are bi-amping the speakers or you could severely damage the
amplifier. See your speaker manual for more information.
!	 If your speakers have a removable crossover network, make sure you do not remove it for bi-amping. Doing so
may damage your speakers.

22

　
　
　
　

03

Connecting your equipment

Selecting the Speaker system

About the audio connection

The front height terminals can be used for front wide and Speaker B connections, in addition to for the front
height speakers. Also, the surround back terminals can be used for bi-amping and ZONE 2 connections, in addition to for the surround back speakers. Make this setting according to the application.
Sound signal priority

Types of cables and terminals
HDMI

Front height setup
*Default setting

1	

Connect a pair of speakers to the front height speaker terminals.

See Standard surround connection on page 21.

2	

If necessary, select ‘Normal(SB/FH)’ from the Speaker System menu.

Digital (Coaxial)

Transferable audio signals
HD audio

Conventional digital audio

Digital (Optical)

See Speaker system setting on page 84 to do this.
RCA (Analog)
(White/Red)

Front wide setup
1	

Conventional analog audio

Connect a pair of speakers to the front height speaker terminals.

See Standard surround connection on page 21.

2	

Select ‘Normal(SB/FW)’ from the Speaker System menu.

!	 With an HDMI cable, video and audio signals can be transferred in high quality over a single cable.

See Speaker system setting on page 84 to do this.

Speaker B setup
You can listen to stereo playback in another room.

1	

Connect a pair of speakers to the front height speaker terminals.

See Standard surround connection on page 21.

2	

Select ‘Speaker B’ from the Speaker System menu.

See Speaker system setting on page 84 to do this.

Bi-Amping setup
Bi-amping connection of the front speakers for high sound quality with 5.1-channel surround sound.

1	

Connect bi-amp compatible speakers to the front and surround back speaker terminals.

See Bi-amping your speakers on page 22.

2	

Select ‘Front Bi-Amp’ from the Speaker System menu.

See Speaker system setting on page 84 to do this.

ZONE 2 setup
With these connections you can simultaneously enjoy 5.1-channel surround sound in the main zone with stereo
playback on another component in ZONE 2.

1	

Connect a pair of speakers to the surround back speaker terminals.

See Standard surround connection on page 21.

2	

Select ‘ZONE 2’ from the Speaker System menu.

See Speaker system setting on page 84 to do this.

23

　
　
　
　

03

Connecting your equipment

About the video converter

About HDMI

The video converter ensures that all video sources are output through the HDMI OUT terminal.
If the TV is only connected to the receiver’s composite VIDEO MONITOR OUT jacks, all the other video devices
must be connected through composite connections.
If several video components are assigned to the same input function (see The Input Setup menu on page 39), the
converter gives priority to HDMI, component, then composite (in that order).

The HDMI connection transfers uncompressed digital video, as well as almost every kind of digital audio.
This receiver incorporates High-Definition Multimedia Interface (HDMI®) technology.
This receiver supports the functions described below through HDMI connections.
!	 Digital transfer of uncompressed video (contents protected by HDCP (1080p/24, 1080p/60, etc.))
!	 3D signal transfer
!	 Deep Color signal transfer
!	 x.v.Color signal transfer
!	 ARC (Audio Return Channel)
!	 Input of multi-channel linear PCM digital audio signals (192 kHz or less) for up to 8 channels
!	 Input of the following digital audio formats:
—	Dolby Digital, Dolby Digital Plus, DTS, High bitrate audio (Dolby TrueHD, DTS-HD Master Audio, DTS-HD
High Resolution Audio), DVD-Audio, CD, SACD (DSD signal), Video CD, Super VCD
!	 Synchronized operation with components using the Control with HDMI function (see Control with HDMI function on page 58)

High picture quality

Terminal for connection
with source device

Terminal for connection
with TV monitor

HDMI IN

Y

PB

HDMI OUT

PR

Y

PB

PR

COMPONENT
VIDEO IN

COMPONENT VIDEO
MONITOR OUT

VIDEO IN

VIDEO
MONITOR OUT

Note

Video signals
can be output

!	 An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High
Bandwidth Digital Content Protection (HDCP). If you choose to connect to a DVI connector, you will need a
separate adaptor (DVIdHDMI) to do so. A DVI connection, however, does not support audio signals. Consult
your local audio dealer for more information.
!	 If you connect a component that is not compatible with HDCP, an HDCP ERROR message is displayed on
the front panel display. Some components that are compatible with HDCP still cause this message to be displayed, but so long as there is no problem with displaying video this is not a malfunction.
!	 Depending on the component you have connected, using a DVI connection may result in unreliable signal
transfers.
!	 This receiver supports SACD, Dolby Digital Plus, Dolby TrueHD and DTS-HD Master Audio. To take advantage
of these formats, however, make sure that the component connected to this receiver also supports the corresponding format.
!	 Use a High Speed HDMI® cable. If an HDMI cable other than a High Speed HDMI® cable is used, it may not
work properly.
!	 When an HDMI cable with a built-in equalizer is connected, it may not operate properly.
!	 Signal transfer is only possible when connected to a compatible component.
!	 HDMI format digital audio transmissions require a longer time to be recognized. Due to this, interruption in the
audio may occur when switching between audio formats or beginning playback.
!	 Turning on/off the device connected to this unit’s HDMI OUT terminal during playback, or disconnecting/connecting the HDMI cable during playback, may cause noise or interrupted audio.

Note
!	 The only exception is HDMI: since this resolution cannot be downsampled, you must connect your monitor/TV
to the receiver’s HDMI output when connecting this video source.
!	 If the video signal does not appear on your TV, try adjusting the resolution settings on your component or display. Note that some components (such as video game units) have resolutions that may not be converted. In
this case, try switching Digital Video Conversion (in Setting the Video options on page 64) OFF.
!	 The signal input resolutions that can be converted from the component video input for the HDMI output are
480i/576i, 480p/576p, 720p and 1080i. 1080p signals cannot be converted.
This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property
rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing, LLC in the United States and other countries.
“x.v.Color” and

24

are trademarks of Sony Corporation.

　
　
　
　

03

Connecting your equipment

!	 For input components, connections other than HDMI connections are also possible (see Connecting your DVD
player with no HDMI output on page 26).
!	 If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables.
—	When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT terminal, so
there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on
page 59).
—	If you use a coaxial digital audio cable or RCA (analog) audio cable, you’ll need to tell the receiver which digital or analog audio input you connected the TV to (see The Input Setup menu on page 39).

Connecting your TV and playback components
Connecting using HDMI
If you have an HDMI or DVI (with HDCP) equipped component (Blu-ray Disc player (BD), etc.), you can connect it
to this receiver using a commercially available HDMI cable.
If the TV and playback components support the Control with HDMI feature, the convenient Control with HDMI
functions can be used (see Control with HDMI function on page 58).

HDMI/DVI-compatible
Blu-ray Disc player

This connection is required in
order to listen to the sound of
the TV over the receiver.

Other HDMI/DVIequipped component

HDMI OUT

HDMI OUT

HDMI/DVI-compatible
monitor

Select one

HDMI IN

AUDIO OUT
R ANALOG L

IN 1
(DVD)

HDMI
ASSIGNABLE
1 -6

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

DIGITAL OUT
OPTICAL COAXIAL

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

IN 1
DC OUTPUT

for WIRELESS LAN

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

IN 1 (CD)
ASSIGNABLE
HDMI

IN 1
(DVD)

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

(OUTPUT 5 V
0.6 A MAX)

ASSIGNABLE
1 -6

LAN (10/100)

IN 1
DC OUTPUT

for WIRELESS LAN

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL

IN 1 (CD)
ASSIGNABLE

25

　
　
　
　

03

Connecting your equipment

Connecting your DVD player with no HDMI output

Connecting your TV with no HDMI input

This diagram shows connections of a TV (with HDMI input) and DVD player (or other playback component with no
HDMI output) to the receiver.

This diagram shows connections of a TV (with no HDMI input) and DVD player (or other playback component) to
the receiver.

HDMI/DVI-compatible monitor

Important

DVD player, etc.

Select one
VIDEO OUT
VIDEO

HDMI IN

Select one
DIGITAL OUT
OPTICAL COAXIAL

COMPONENT VIDEO OUT
Y

!	 With these connections, the picture is not output to the TV even if the DVD player is connected with an HDMI
cable. Connect the receiver and TV using the same type of video cable as used to connect the receiver and
player.
!	 Also, when the receiver and TV are connected by anything other than an HDMI cable, the OSD function allowing display of the receiver’s settings, operations, etc., on the TV’s screen cannot be used. In this case, watch
the receiver’s front panel display while performing the various operations and making settings.

PR

PB

AUDIO OUT
R ANALOG L

DVD player, etc.
TV

Select one
COMPONENT VIDEO IN

IN 1
(DVD)

HDMI
ASSIGNABLE
1 -6
ASSIGNABLE

Y

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

PB

Y

PB

Select one

PR

DIGITAL OUT
OPTICAL COAXIAL

HDMI OUT

VIDEO OUT
VIDEO

AUDIO OUT
R ANALOG L

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

COMPONENT VIDEO

PR

PB

Y

Select one
COMPONENT VIDEO OUT

VIDEO IN
VIDEO

PR

IN 1
(TV)

DC OUTPUT

for WIRELESS LAN

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

IN 1
(DVD)
IN 2
(DVR/
BDR)

DVD
IN
IN 1
(DVD)

HDMI

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

ASSIGNABLE
1 -6
ASSIGNABLE

Y

PB

BD IN

IN 4
(VIDEO)

IN 6

OUT

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

COMPONENT VIDEO
PR

IN 1
DC OUTPUT

for WIRELESS LAN

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

ASSIGNABLE
1 -6

IN 2
(DVR/
BDR)

IN 1
(DVD)

HDMI

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

IN 1
(DVD)

DVD
IN

ASSIGNABLE

Y

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

LAN (10/100)

COMPONENT VIDEO
PB

(OUTPUT 5 V
0.6 A MAX)

PR

MONITOR
OUT

IN 1
(DVD)

IN 1
(TV)

DC OUTPUT

for WIRELESS LAN

IN 2
(DVR/
BDR)

!	 If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables
(page 25).
—	When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT terminal, so
there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on
page 59).
!	 If you use an optical digital audio cable, you’ll need to tell the receiver which digital input you connected the
player to (see The Input Setup menu on page 39).

DVD
IN

MONITOR
OUT

IN 1
(DVD)

HDMI

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

ASSIGNABLE
1 -6
ASSIGNABLE

Y

PB

PR

MONITOR
OUT

IN 2
(DVR/
BDR)

MONITOR
OUT

26

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

COMPONENT VIDEO

IN 1
(DVD)

DVD
IN

IN 1
DC OUTPUT

for WIRELESS LAN

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

　
　
　
　

03

Connecting your equipment

!	 In order to listening to HD audio with this receiver, connect an HDMI cable, and use analog video cable for
video signal input.
	 Depending on the player, it may not be possible to output video signals to both HDMI and other video output
(composite, etc.) simultaneously, and it may be necessary to make video output settings. Please refer to the
operating instructions supplied with your player for more information.
!	 If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables
(page 25).
!	 If you use an optical digital audio cable, you’ll need to tell the receiver which digital input you connected the
player to (see The Input Setup menu on page 39).

Connecting an HDD/DVD recorder, BD recorder and other video
sources
This receiver has audio/video inputs suitable for connecting analog or digital video devices, including HDD/DVD
recorders and BD recorders.
When you set up the receiver you’ll need to tell the receiver which input you connected the recorder to (see also
The Input Setup menu on page 39).
HDD/DVD recorder, BD recorder, etc.

Select one
VIDEO IN
VIDEO

AUDIO IN
R ANALOG L

IN 1
(DVD)

HDMI
ASSIGNABLE
1 -6

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

VIDEO OUT
VIDEO

BD IN

IN 4
(VIDEO)

IN 6

AUDIO OUT
R ANALOG L

OUT

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

VIDEO

DIGITAL OUT
OPTICAL COAXIAL

IN 1
DC OUTPUT

for WIRELESS LAN

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

DVR/BDR
OUT
IN

HDMI

IN 1
(DVD)

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

ASSIGNABLE
1 -6

OUT

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

VIDEO

IN 1
DC OUTPUT

for WIRELESS LAN

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

AUDIO

DVR/BDR
OUT
IN

AUDIO

!	 In order to record, you must connect the analog audio cables (the digital connection is for playback only) (page
67).

27

　
　
　
　

03

Connecting your equipment

!	 If your HDD/DVD recorder, BD recorder, etc., is equipped with an HDMI output terminal, we recommend connecting it to the receiver’s HDMI DVR/BDR IN terminal. When doing so, also connect the receiver and TV by
HDMI (see Connecting using HDMI on page 25).

Satellite and cable receivers, and terrestrial digital TV tuners are all examples of so-called ‘set-top boxes’.
When you set up the receiver you’ll need to tell the receiver which input you connected the set-top box to (see The
Input Setup menu on page 39).

HDMI/DVI-compatible monitor

HDD/DVD recorder, BD recorder, etc.

HDMI OUT

Connecting a satellite/cable receiver or other set-top box

STB

HDMI IN

HDMI
ASSIGNABLE
1 -6

IN 1
(DVD)

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

Select one
HDMI

IN 1
(DVD)

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

VIDEO OUT
VIDEO

OUT

ASSIGNABLE
1 -6

IN 1
(DVD)

HDMI
ASSIGNABLE
1 -6

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

DIGITAL OUT
OPTICAL COAXIAL

AUDIO OUT
R ANALOG L

IN 6

OUT

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

HDMI

IN 1
(DVD)

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

LAN (10/100)

IN 1
DC OUTPUT

for WIRELESS LAN

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

(TV)

IN 2
(DVR/BDR)

ASSIGNOPTICAL ABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

SAT/CBL
IN

(OUTPUT 5 V
0.6 A MAX)

ASSIGNABLE
1 -6

IN 1
DC OUTPUT

for WIRELESS LAN

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

SAT/CBL
IN

!	 If your set-top box is equipped with an HDMI output terminal, we recommend connecting it to the receiver’s
HDMI SAT/CBL IN terminal. When doing so, also connect the receiver and TV by HDMI (see Connecting using
HDMI on page 25).
STB

HDMI OUT

HDMI/DVI-compatible monitor

HDMI IN

HDMI
ASSIGNABLE
1 -6

28

IN 1
(DVD)

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT
HDMI
ASSIGNABLE
1 -6

IN 1
(DVD)

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

　
　
　
　

03

Connecting your equipment

!	 Even if your set-top box is equipped with an HDMI output terminal, in some cases the sound is output from
the digital audio output (optical or coaxial) and only the video is output from the HDMI output terminal. In this
case, make the HDMI and digital audio connections as shown below.

Connecting other audio components
This receiver has both digital and analog inputs, allowing you to connect audio components for playback.
When you set up the receiver you’ll need to tell the receiver which input you connected the component to (see
also The Input Setup menu on page 39).

Select one
DIGITAL OUT
OPTICAL COAXIAL

STB

HDMI OUT

CD player, etc.

Select one
AUDIO OUT
R ANALOG L
HDMI
ASSIGNABLE
1 -6

IN 1
(DVD)

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

HDMI
ASSIGNABLE
1 -6

IN 1
(DVD)

IN 1
DC OUTPUT

for WIRELESS LAN

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

OUT

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

HDMI/DVI-compatible monitor

DIGITAL OUT
OPTICAL COAXIAL

IN 1
DC OUTPUT

for WIRELESS LAN

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

IN 1
(DVD)

HDMI

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

ASSIGNABLE
1 -6

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

HDMI IN

IN 1
DC OUTPUT

for WIRELESS LAN

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

COAXIAL ASSIGNABLE

IN 1 (CD)
HDMI

IN 1
(DVD)

IN 2
(SAT/CBL)

IN 3
(DVR/BDR)

BD IN

IN 4
(VIDEO)

IN 6

OUT

(OUTPUT 5 V
0.6 A MAX)

ASSIGNABLE
1 -6

LAN (10/100)

IN 1
DC OUTPUT

for WIRELESS LAN

(TV)

IN 2
(DVR/BDR)
ASSIGN-

OPTICAL ABLE

IN 1
(DVD)

IN 2
(SAT/CBL)

ASSIGNABLE

COAXIAL ASSIGNABLE

IN 1 (CD)
ASSIGNABLE

!	 If your turntable has line-level outputs (i.e., it has a built-in phono pre-amp), connect it to the ANALOG IN 1
(CD) inputs instead.

29

　
　
　
　

03

Connecting your equipment

Connecting additional amplifiers

Connecting AM/FM antennas

This receiver has more than enough power for any home use, but it’s possible to add additional amplifiers to every
channel of your system using the pre-outs. Make the connections shown below to add amplifiers to power your
speakers.

Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality,
connect external antennas (see Connecting external antennas on page 31).

a

ANALOG
INPUT

b

c

L
R
FRONT

1

SUBWOOFER

PRE OUT

2

SURROUND SURR BACK FH / FW
(Single)

L

Front channel
amplifier

R
CENTER

ANALOG
INPUT

3

Center channel
amplifier (mono)

5

ANTENNA

ANALOG
INPUT
L
R

Surround
channel amplifier

4
1

ANALOG
INPUT

1

SUBWOOFER

PRE OUT

SURROUND SURR BACK FH / FW
2
(Single)

R

L

ANTENNA

Front height or Front wide
channel amplifier

AM LOOP

ANALOG
INPUT

R

1	

L

CENTER

R

ANALOG
INPUT

ANALOG
INPUT

FM UNBAL 75

2

L

FRONT

AM LOOP

FM UNBAL 75

Pull off the protective shields of both AM antenna wires.

2	 Push open the tabs, then insert one wire fully into each terminal, then release the tabs to
secure the AM antenna wires.

Surround back
channel amplifier

3	

Powered
subwoofer 2

Fix the AM loop antenna to the attached stand.

To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. a) then clip the loop onto the
stand (fig. b).
!	 If you plan to mount the AM antenna to a wall or other surface, secure the stand with screws (fig. c) before
clipping the loop to the stand. Make sure the reception is clear.

Powered
subwoofer 1

!	 If you’re not using a subwoofer, change the front speaker setting (see Speaker Setting on page 80) to LARGE.
!	 You can use the additional amplifier on the surround back channel pre-outs for a single speaker as well. In this
case plug the amplifier into the left (SURROUND BACK L (Single)) terminal only.
!	 The sound from the surround back terminals will depend on how you have configured the Speaker system setting on page 84.
!	 If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal.
Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this
case, the same sound is output from the two subwoofers.
!	 To hear sound only from the pre-outs, switch the speaker terminals to SP: OFF (page 66) or simply disconnect
any speakers that are connected directly to the receiver.

4	

Place the AM antenna on a flat surface and in a direction giving the best reception.

5	

Connect the FM wire antenna into the FM antenna socket.

For best results, extend the FM antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up.

30

　
　
　
　

03

Connecting your equipment

MULTI-ZONE listening options

Connecting external antennas

The following table shows the signals that can be output to ZONE 2 and ZONE 3:

To improve FM reception, connect an external FM antenna to FM UNBAL 75 W.

Sub Zone

75 Ω coaxial cable

ANTENNA
FM UNBAL 75

AM LOOP

ZONE 2

DVD, SAT/CBL, DVR/BDR, VIDEO, INTERNET RADIO, SiriusXM, PANDORA, MEDIA
SERVER, FAVORITES, iPod/USB, TV, CD, TUNER, ADAPTER PORT
(Outputs analog audio, composite video.)

ZONE 3

DVD, SAT/CBL, DVR/BDR, VIDEO, TV, CD, TUNER, ADAPTER PORT
(Outputs analog audio)

!	 It is not possible to down-convert the audio and video input signals from the HDMI input terminals, digital input terminals
(OPTICAL and COAXIAL) and the COMPONENT VIDEO input terminals and output them to ZONE 2.
!	 It is not possible to down-convert the audio input signal from the HDMI input terminals or digital input terminals (OPTICAL and
COAXIAL) and output them to ZONE 3.
!	 When any of the INTERNET RADIO, SiriusXM, PANDORA, MEDIA SERVER, FAVORITES, iPod/USB or ADAPTER PORT inputs
is selected in the main zone, it is only possible to select the same input as in the main zone for the sub zone. (Inputs other than
the ones listed here can be selected.)

ANTENNA

AM LOOP

Input functions available

FM UNBAL 75

To improve AM reception, connect a 5 m to 6 m (16 ft. to 20 ft.) length of vinyl-coated wire to the AM LOOP terminals without disconnecting the supplied AM loop antenna.
For the best possible reception, suspend horizontally outdoors.

Basic MULTI-ZONE setup (ZONE 2)
1	

Connect a separate amplifier to the AUDIO ZONE 2 OUT jacks on this receiver.

You should have a pair of speakers attached to the sub zone amplifier as shown in the following illustration.
Outdoor antenna

ANTENNA

2	

Connect a subwoofer to the SUBWOOFER ZONE 2 OUT jack on this receiver.

When a subwoofer is connected, we recommend setting HPF (High Pass Filter) at ZONE Setup to ON (page 89).
AM LOOP

FM UNBAL 75

3	

Connect a TV monitor to the VIDEO ZONE 2 OUT jack on this receiver.
Sub zone (ZONE 2)

3
VIDEO IN

ANTENNA

Indoor antenna
(vinyl-coated wire)

5 m to 6 m
(16 ft. to 20 ft.)

AM LOOP

Main zone

FM UNBAL 75

ZONE 2
OUT

MULTI-ZONE setup
This receiver can power up to three independent systems in separate rooms after you have made the proper
MULTI-ZONE connections.
Different sources can be playing in three zones at the same time or, depending on your needs, the same source
can also be used. The main and sub zones have independent power (the main zone power can be off while one (or
both) of the sub zones is on) and the sub zones can be controlled by the remote or front panel controls.

LINE LEVEL
INPUT

AUDIO IN
R
L
SUBWOOFER

2

Making MULTI-ZONE connections

1
ZONE 2
OUT

It is possible to make these connections if you have a separate TV, subwoofer and speakers for your primary
(ZONE 2) sub zone, and a separate amplifier (and speakers) for your secondary (ZONE 3) sub zone. You will also
need a separate amplifier if you are not using the speaker terminals for your primary sub zone (For detail, see
MULTI-ZONE setup using speaker terminals (ZONE 2) on page 32). There are two primary sub zone setups possible with this system. Choose whichever works best for you.

SUBWOOFER

31

　
　
　
　

03

Connecting your equipment

MULTI-ZONE setup using speaker terminals (ZONE 2)

Connecting to the network through LAN interface

You must select ZONE 2 in Speaker system setting (page 84) to use this setup.

1	

By connecting this receiver to the network via the LAN terminal, you can listen to Internet radio stations. To listen
to Internet radio stations, you must sign a contract with an ISP (Internet Service Provider) beforehand.
When connected in this way, you can play audio files stored on the components on the local network, including
your computer.

Connect a pair of speakers to the surround back speaker terminals.

You should have a pair of speakers attached to the surround back speaker terminals as shown below.

2	

Connect a TV monitor to the VIDEO ZONE 2 OUT jack on this receiver.
Sub zone (ZONE 2)

Main zone

2
ZONE 2
OUT

VIDEO IN

R

SURROUND BACK

Internet

L

(Single)

LAN (10/100)

Modem
LAN (10/100)
L

ZONE 2
OUT

R

R

SURROUND BACK

L

(Single)

to LAN port
NAS

PC
LAN
3

1

2

1

WAN

Router

LAN cable (sold separately)
to LAN port

Connect the LAN terminal on this receiver to the LAN terminal on your router (with or without the built-in DHCP
server function) with a straight LAN cable (CAT 5 or higher).
Turn on the DHCP server function of your router. In case your router does not have the built-in DHCP server function, it is necessary to set up the network manually. For details, see Network Setup menu on page 86.

Secondary MULTI-ZONE setup (ZONE 3)
%	 Connect a separate amplifier to the AUDIO ZONE 3 OUT jacks on this receiver.
You should have a pair of speakers attached to the sub zone amplifier as shown in the following illustration.
Sub zone (ZONE 3)

LAN terminal specifications

Main zone

!	 LAN terminal : Ethernet jack (10BASE-T/100BASE-TX)

Note

ZONE 3
OUT

!	 Refer to the operation manual of the equipment you have as the connected equipment and connection method
may differ depending on your Internet environment.
!	 When using a broadband Internet connection, a contract with an Internet service provider is required. For
more details, contact your nearest Internet service provider.

AUDIO IN
R
L

ZONE 3
OUT

32

　
　
　
　

03

Connecting your equipment

Connecting optional Bluetooth ADAPTER

Tip

When the Bluetooth® ADAPTER (AS-BT100 or AS-BT200) is connected to this receiver, a product equipped with
Bluetooth wireless technology (portable cell phone, digital music player, etc.) can be used to listen to music
wirelessly.
!	The Bluetooth wireless technology enabled device must support A2DP profiles.
!	 Pioneer does not guarantee proper connection and operation of this unit with all Bluetooth wireless technology
enabled devices.
!	 The Air Jam function cannot be used with the AS-BT100.

!	 An iPod/iPhone/iPad can be connected to the receiver. For details on supported models and versions of the
respective products, see Playing an iPod on page 43.

%	 Switch the receiver into standby then use the supplied iPod cable to connect your iPod to
the iPod iPhone iPad USB terminal on the front panel of this receiver.
!	 It is also possible to connect using the cable included with the iPod, but in this case it is not possible to view
pictures via the receiver.
!	 For the cable connection, also refer to the operating instructions for your iPod.
!	 iPod recharging occurs whenever an iPod is connected to this unit. (Recharging is enabled only when the
unit’s power is turned on.)
!	 For instructions on playing the iPod, see Playing an iPod on page 43.

ADAPTER PORT
(OUTPUT 5 V
0.1 A MAX)

Bluetooth® ADAPTER

Connecting a USB device
It is possible to play audio and photo files by connecting USB devices to this receiver.

ADAPTER PORT
(OUTPUT 5 V
0.1 A MAX)

iPod iPhone iPad
DIRECT CONTROL

Important

AUTO SURR/ALC/
STREAM DIRECT

5V

!	 Do not move the receiver with the Bluetooth ADAPTER connected. Doing so could cause damage or faulty
contact.

USB
2.1 A

STEREO

STANDARD
SURROUND

ADVANCED
SURROUND

HDMI 5 INPUT

iPod iPhone iPad

%	 Switch the receiver into standby and connect Bluetooth ADAPTER to the ADAPTER PORT.

!	 For instructions on playing the Bluetooth wireless technology device, see Pairing the Bluetooth ADAPTER and
Bluetooth wireless technology device on page 46.
USB mass
storage device

Connecting an iPod
This receiver has a dedicated iPod terminal that will allow you to control playback of audio content from your iPod
using the controls of this receiver.
iPod iPhone iPad
DIRECT CONTROL

AUTO SURR/ALC/
STREAM DIRECT

5V

USB
2.1 A

STEREO

STANDARD
SURROUND

%	 Switch the receiver into standby then connect your USB device to the USB terminal on the
front panel of this receiver.
!	 This receiver does not support a USB hub.
!	 For instructions on playing the USB device, see Playing a USB device on page 44.

ADVANCED
SURROUND

HDMI 5 INPUT

iPod iPhone iPad

iPod/iPhone/iPad
iPod cable
(supplied)

33

　
　
　
　

03

Connecting your equipment

Connecting an HDMI-equipped component to the front panel
input
iPod iPhone iPad
DIRECT CONTROL

AUTO SURR/ALC/
STREAM DIRECT

5V

STEREO

USB
2.1 A

STANDARD
SURROUND

Connecting an IR receiver
If you keep your stereo components in a closed cabinet or shelving unit, or you wish to use the sub zone remote
control in another zone, you can use an optional IR receiver (such as a Niles or Xantech unit) to control your
system instead of the remote sensor on the front panel of this receiver.
!	 Remote operation may not be possible if direct light from a strong fluorescent lamp is shining on the IR
receiver remote sensor window.
!	 Note that other manufacturers may not use the IR terminology. Refer to the manual that came with your component to check for IR compatibility.
!	 If using two remote controls (at the same time), the IR receiver’s remote sensor takes priority over the remote
sensor on the front panel.

ADVANCED
SURROUND

HDMI 5 INPUT

iPod iPhone iPad

1	

Connect the IR receiver sensor to the IR IN jack on the rear of this receiver.
Closet or shelving unit
Non-Pioneer
component

Video camera (etc.)

IR

IN

IR

Connecting to a wireless LAN

IN

OUT

Wireless connection to the network is possible through a wireless LAN connection. Use the separately sold
AS-WL300 for connection.
!	 Use only the furnished accessory connecting cable.
!	 Certain settings are required to use a wireless LAN converter (AS-WL300). For instructions on making these
settings, see the operating instructions included with the wireless LAN converter (AS-WL300).
IR
OUT

IN

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

DC OUTPUT

IR receiver

for WIRELESS LAN

(OUTPUT 5 V
0.6 A MAX)

LAN (10/100)

2	 Connect the IR IN jack of another component to the IR OUT jack on the rear of this receiver
to link it to the IR receiver.

DC OUTPUT

for WIRELESS LAN

Modem

Please see the manual supplied with your IR receiver for the type of cable necessary for the connection.

Internet

Router
WAN

DC 5V

Ethernet

WPS

Wireless LAN converter (AS-WL300)

34

　
　
　
　

03

Connecting your equipment

　
　
　
　

Plugging in the receiver
Only plug in after you have connected all your components to this receiver, including the speakers.

CAUTION
!	 Handle the power cord by the plug part. Do not pull out the plug by tugging the cord, and never touch the
power cord when your hands are wet, as this could cause a short circuit or electric shock. Do not place the
unit, a piece of furniture, or other object on the power cord or pinch the cord in any other way. Never make a
knot in the cord or tie it with other cables. The power cords should be routed so that they are not likely to be
stepped on. A damaged power cord can cause a fire or give you an electric shock. Check the power cord once
in a while. If you find it damaged, ask your nearest Pioneer authorized independent service company for a
replacement.
!	 Do not use any power cord other than the one supplied with this unit.
!	 Do not use the supplied power cord for any purpose other than that described below.
!	 The receiver should be disconnected by removing the mains plug from the wall socket when not in regular use,
e.g., when on vacation.

1	

Plug the supplied power cord into the AC IN socket on the back of the receiver.

2	

Plug the other end into a power outlet.

!	 After this receiver is connected to an AC outlet, a 2 second to 10 second HDMI initialization process begins.
You cannot carry out any operations during this process. The HDMI indicator in the front panel display blinks
during this process, and you can turn on this receiver once it has stopped blinking. When you set the Control
with HDMI to OFF, you can skip this process. For details about the Control with HDMI feature, see Control
with HDMI function on page 58.

35

Basic Setup
Changing the OSD display language (OSD Language)............................................................... 37
Automatically conducting optimum sound tuning (Full Auto MCACC)..................................... 37
The Input Setup menu.................................................................................................................... 39
Operation Mode Setup.................................................................................................................. 40
About the Home Menu.................................................................................................................. 40

36

　
　
　
　

04

Basic Setup

Changing the OSD display language (OSD Language)

Automatically conducting optimum sound tuning (Full Auto
MCACC)

The language used on the Graphical User Interface screen can be changed.
!	 The explanations in these operating instructions are for when English is selected for the GUI screen.
!	 The OSD display is only displayed when the receiver’s HDMI OUT terminal and the TV’s HDMI input are connected with an HDMI cable. If the TV is connected with anything other than an HDMI cable, watch the front
panel display while performing the various operations and making settings.

The Full Auto MCACC Setup measures the acoustic characteristics of your listening area, taking into account
ambient noise, speaker connection and speaker size, and tests for both channel delay and channel level. After
you have set up the microphone provided with your system, the receiver uses the information from a series of test
tones to optimize the speaker settings and equalization for your particular room.

1	Press u RECEIVER to switch on the receiver and your TV.
Make sure that the TV’s video input is set to this receiver (for example, if you connected this receiver to the VIDEO
jacks on your TV, make sure that the VIDEO input is now selected).

2	Press

Important
!	
!	
!	
!	

on the remote control, then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.

3	

Select ‘System Setup’ from the Home Menu.

4	

Select ‘OSD Language’ from the System Setup menu.

5	

Select the desired language.

6	

Select ‘OK’ to change the language.

Make sure the microphone and speakers are not moved during the Full Auto MCACC Setup.
Using the Full Auto MCACC Setup will overwrite any existing settings for the MCACC preset you select.
Before using the Full Auto MCACC Setup, the headphones should be disconnected.
The OSD display is only displayed when the receiver’s HDMI OUT terminal and the TV’s HDMI input are connected with an HDMI cable. If the TV is connected with anything other than an HDMI cable, watch the front
panel display while performing the various operations and making settings.

CAUTION
!	 The test tones used in the Full Auto MCACC Setup are output at high volume.

The setting is completed and the System Setup menu reappears automatically.

THX®
!	 THX is a trademark of THX Ltd. which is registered in some jurisdictions. All rights reserved.

1	Press u RECEIVER to switch on the receiver and your TV.
Make sure that the TV’s video input is set to this receiver.

2	

Connect the microphone to the MCACC SETUP MIC jack on the front panel.
MULTI-ZONE
CONTROL
ON/OFF

SPEAKERS

iPod iPhone iPad
DIRECT CONTROL

AUTO SURR/ALC/
STREAM DIRECT

STEREO

STANDARD
SURROUND

ADVANCED
SURROUND

BAND

PHONES
TUNER EDIT

MCACC
SETUP MIC

5V

USB
2.1 A

HDMI 5 INPUT

iPod iPhone iPad

Microphone

Tripod

Make sure there are no obstacles between the speakers and the microphone.
If you have a tripod, use it to place the microphone so that it’s about ear level at your normal listening position. If
you do not have a tripod, use some other object to install the microphone.
Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make
accurate measurement impossible:
!	 Sofas or other soft surfaces.
!	 High places such as tabletops and sofa tops.

37

　
　
　
　

04

Basic Setup

The Full Auto MCACC display appears once the microphone is connected.

1a.Full Auto MCACC

1a.Full Auto MCACC

A/V RECEIVER

Now Analyzing...

1a.Full Auto MCACC

L
FHL
C
FHR
R
SR
SBR
SBL
SL
SW
10

2/9

A/V RECEIVER

Speaker System
EQ Type
MCACC
THX Speaker

: Normal(SB/FH)
: SYMMETRY
: M1.MEMORY 1
:
NO

Environment Check
Ambient Noise
: OK
Microphone
:
Speaker YES/NO :

START

Exit
Exit

Return

Select the parameters you want to set.

!	 When data measurement is taken, the reverb characteristics data (both before- and after-calibration) that this
receiver had been storing will be overwritten.
!	 When measurement is taken of the reverb characteristics data other than SYMMETRY, the data are not
measured after the correction. If you will need to measure after correcting data, take the measurement using
the EQ Professional menu in the Manual MCACC setup (page 78).
If the speakers are connected using any setup other than Normal(SB/FH), be sure to set Speaker System before
the Full Auto MCACC Setup. See Speaker system setting on page 84.
!	 Speaker System – Shows the current settings. When this is selected and ENTER is pressed, the speaker
system selection screen appears. Select the proper speaker system, then press RETURN to return.
	 If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another
room, read through Speaker system setting on page 84 and make sure to connect your speakers as necessary
before continuing to step 4.
!	 EQ Type – This determines how the frequency balance is adjusted. Normally select SYMMETRY. For details,
see Automatic MCACC (Expert) on page 76.
!	 MCACC – The six MCACC presets are used for storing surround sound settings for different listening positions. Simply choose an unused preset for now (you can rename it later in Data Management on page 81).
!	 THX Speaker – Select YES when using THX speakers (all speakers other than the front speakers are set to
SMALL). In other cases, leave at NO.

4	Press
5	

7	

RETRY
Cancel

Make sure ‘OK’ is selected, then press ENTER.

A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum
receiver settings.
Again, try to be as quiet as possible while this is happening. It may take 3 to 10 minutes.

8	 The Full Auto MCACC Setup procedure is completed and the Home Menu menu reappears
automatically.
Be sure to disconnect the microphone from this receiver upon completion of the Full Auto MCACC Setup.
The settings made in the Full Auto MCACC Setup should give you excellent surround sound from your system,
but it is also possible to adjust these settings manually using The Advanced MCACC menu on page 75 or The
System Setup and Other Setup menus on page 83.
!	 Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12
cm (5 inches) will end up with different size settings. You can correct the setting manually using the Manual
speaker setup on page 84.
!	 The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and room characteristics into account) and generally does not need to
be changed.
!	 If Full Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing environment, we recommend adjusting the settings manually.

then select START.

Follow the instructions on-screen.

Make sure the microphone is connected, and if you’re using a subwoofer, make sure it is switched on and set to a
comfortable volume level.

6	

OK

Exit

A/V RECEIVER
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES

The configuration shown on-screen should reflect the actual speakers you have.
!	 If you see an ERR message (or the speaker configuration displayed isn’t correct), there may be a problem
with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker connections. If there doesn’t seem to be a problem, you can simply use i/j to select the speaker and k/l to
change the setting and continue.
!	 If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the
phase (dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are
properly connected.
	If Reverse Phase is displayed, the speaker’s wiring (+ and –) may be inverted. Check the speaker
connections.
—	 If the connections were wrong, turn off the power, disconnect the power cord, then reconnect properly.
After this, perform the Full Auto MCACC procedure again.
—	 If the connections were right, select GO NEXT and continue.

!	 If you leave the GUI screen for over five minutes, the screen saver will appear.

3	

Cancel

:
:
:
:
:
:
:
:
:
:

Wait for the test tones to finish, then confirm the speaker configuration in the GUI screen.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present
in your setup. Try to be as quiet as possible while it’s doing this.
If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed,
the Full Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press
ENTER in step 7.
!	 With error messages (such as Too much ambient noise! or Check microphone.), select RETRY after checking for ambient noise (see Problems when using the Auto MCACC Setup on page 38) and verifying the mic
connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.

Problems when using the Auto MCACC Setup
If the room environment is not optimal for the Auto MCACC Setup (too much background noise, echo off the
walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for
household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them
off if necessary. If there are any instructions showing in the front panel display, please follow them.
!	 Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off
the TV when doing the Auto MCACC Setup.

38

　
　
　
　

04

Basic Setup

Input function default and possible settings

The Input Setup menu

The terminals on the receiver generally correspond to the name of one of the input functions. If you have connected components to this receiver differently from (or in addition to) the defaults below, see The Input Setup
menu on page 39 to tell the receiver how you’ve connected up. The dots (k) indicate possible assignments.

You only need to make settings in the Input Setup menu if you didn’t hook up your digital equipment according
to the default settings (see Input function default and possible settings on page 39). In this case, you need to tell
the receiver what equipment is hooked up to which terminal so the buttons on the remote control correspond to
the components you’ve connected.
!	 The OSD display is only displayed when the receiver’s HDMI OUT terminal and the TV’s HDMI input are connected with an HDMI cable. If the TV is connected with anything other than an HDMI cable, watch the front
panel display while performing the various operations and making settings.

1	Press

Input function
BD

on the remote control, then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.

2	

Select ‘System Setup’ from the Home Menu.

3	

Select ‘Input Setup’ from the System Setup menu.
4b.Input Setup

4.System Setup

A/V RECEIVER

A/V RECEIVER

a.Manual SP Setup
b. Input Setup
c. OSD Language
d. Network Setup
e. HDMI Setup
f. Other Setup

Input Terminals
HDMI

Audio

Component
IN 1

(BD)

DVD

IN 1

COAX-1

SAT/CBL

IN 2

COAX-2

k

DVR/BDR

IN 3

OPT-2

IN 2

k

k

VIDEO

IN 4

HDMI 5
(front panel)

IN 5

HDMI 6

IN 6

Input
Input Name
Input Skip

:
:
:

DVD
Rename
OFF

INTERNET RADIO

Audio In
HDMI Input
Component In

:
:
:

COAX-1
Input-1
In-1

SiriusXM
PANDORA

Exit

4	

Return

Exit

Return

MEDIA SERVER
FAVORITES

Select the input function that you want to set up.

The default names correspond with the names next to the terminals on the rear panel (such as DVD or SAT/CBL
which, in turn, correspond with the names on the remote control.

5	

iPod/USB

Select the input(s) to which you’ve connected your component.

For example, if your DVD player only has an optical output, you will need to change the DVD input function’s
Audio In setting from COAX-1 (default) to the optical input you’ve connected it to. The numbering (OPT-1 to
OPT-2) corresponds with the numbers beside the inputs on the back of the receiver.

6	

OPT-1


CD

ANALOG-1


TUNER

When you’re finished, proceed to the settings for other inputs.

ADAPTER PORT

There are optional settings in addition to the assignment of the input jacks:
!	 Input Name – You can choose to rename the input function for easier identification. Select Rename to do so,
or Default to return to the system default.
!	 Input Skip – When set to ON, that input is skipped when selecting the input using INPUT SELECT. (DVD and
other inputs can be still be selected directly with the input function buttons.)

7	

TV

a	When ARC at HDMI Setup is set to ON, it is not possible to make assignments to the TV input’s Audio In terminals.
b	 Only the TV and CD inputs can be assigned to ANALOG-1.

When you’re finished, press RETURN.

You will return to the System Setup menu.

39

　
　
　
　

04

Basic Setup

Operation Mode Setup
This receiver is equipped with a great number of functions and settings. The Operation Mode feature is provided
for users who find it difficult to master all these functions and settings.
One of two settings can be selected for the Operation Mode: Expert and Basic.
!	 The OSD display is only displayed when the receiver’s HDMI OUT terminal and the TV’s HDMI input are connected with an HDMI cable. If the TV is connected with anything other than an HDMI cable, watch the front
panel display while performing the various operations and making settings.

1	Press

3	

Select the Operation Mode setting you want.

Descriptions

Page
51

iPod iPhone iPad DIRECT
CONTROL

Switches the input to iPod/USB and sets the mode allowing operation
from the iPod.

43

When you’re finished, press RETURN.

About the Home Menu
This receiver’s Home Menu (HOME MENU) can be used to make various settings and to check and adjust items
that have been set.
To display the Home Menu screen, press
on the remote control, then press HOME MENU.

!	 Expert (default) – Users can set all the functions by themselves.
!	 Basic – The number of operable functions is restricted, and functions whose operations are restricted are
automatically set to achieve the Pioneer-recommended sound and picture quality. The functions that can be
operated are shown below. They can be set as necessary by referring to the operating instructions.
Operable functions/items

Plays with phase shifting in the low range corrected.

4	

on the remote control, then press HOME MENU.

Select ‘Operation Mode Setup’ from the Home Menu.

Descriptions

PHASE (Phase Control)

You will return to the Home Menu.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.

2	

Operable functions/items

HOME MENU
A/V RECEIVER

1. Advanced MCACC
2. MCACC Data Check
3. Data Management
4. System Setup
5. Network Information
6. Operation Mode Setup

Page

HOME MENU

Exit

Full Auto MCACC

Makes high precision sound field settings easily.

37

Input Name

Input names can be changed as desired for easier use.

39

Input Skip

Inputs not being used are skipped (not displayed).

39

Software Update

Updates to the latest version of the software.

88

Network Information

Checks the receiver’s IP address.

87

MCACC
(MCACC preset)

Selects your favorite MCACC preset memory.

62

DELAY
(Sound Delay)

Adjusts the delay time of the overall sound.

62

S.RTRV
(Auto Sound Retriever)

Plays compressed sound with high sound quality.

62

DUAL
(Dual Mono)

Dual monaural audio setting.

62

V.SB
(Virtual Surround Back)

Creates a virtual surround back channel sound for playback.

62

V.HEIGHT
(Virtual Height)

Creates a virtual height channel sound for playback.

62

V.WIDE
(Virtual Wide)

Creates a virtual wide channel sound for playback.

62

V.DEPTH
(Virtual Depth)

Plays with a sound field suited for 3D images.

62

INPUT SELECT (INPUT SELECTOR)

Switches the input.

42

VOLUME +/–, MUTE

Use to set the listening volume.

42

LISTENING MODE

Only Pioneer-recommended modes can be selected.

48

PQLS

Plays using the PQLS function.

60

Return

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.
The top level in the Home Menu is as shown below. Refer to the respective explanations to set, check and adjust
as necessary.
!	 Advanced MCACC – Use this to make automatic settings and detailed manual settings for the surround
sound. For details, see Making receiver settings from the Advanced MCACC menu on page 76.
!	 MCACC Data Check – Use this to check the MCACC memory. For details, see Checking MCACC Data on page
80.
!	 Data Management – Use this to manage the data in the MCACC memory. For details, see Data Management
on page 81.
!	 System Setup – Use this to make various settings related to this system. For details, see Making receiver settings from the System Setup menu on page 84.
!	 Network Information – The setting status of the network-related items can be checked. For detail, see
Checking the Network Information on page 87.
!	 Operation Mode Setup – Use this to select this receiver’s operation mode. For details, see Operation Mode
Setup on page 40.

Audio Parameters

Other functions

40

　
　
　
　

Basic playback
Playing a source.............................................................................................................................. 42
Playing an iPod............................................................................................................................... 43
Playing a USB device...................................................................................................................... 44
Listening to the radio..................................................................................................................... 45
Bluetooth ADAPTER for Wireless Enjoyment of Music............................................................... 46

41

　
　
　
　

05

Basic playback

Turning off the sound

Playing a source

Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound).

Here are the basic instructions for playing a source (such as a DVD disc) with your home theater system.

%	 Press MUTE.

AUTO/ALC/
DIRECT

RECEIVER

1

Playing a source with HDMI connection
%	 Use INPUT SELECT to select the input function connected to the receiver’s HDMI input
terminals.

BDR
BD

DVD

DVR

HDMI

NET

ADPT

TV

CD

USB

CBL

iPod

SAT

INPUT SELECT

You can also perform the same operation by using the INPUT SELECTOR dial on the front panel or by pressing
HDMI on the remote control repeatedly.
!	 Set the HDMI parameter in Setting the Audio options on page 62 to THROUGH if you want to hear HDMI audio
output from your TV (no sound will be heard from this receiver).
!	 If the video signal does not appear on your TV, try adjusting the resolution settings on your component or display. Note that some components (such as video game units) have resolutions that may not be converted. In
this case, use an analog video connection.

TUNER
RECEIVER

VOLUME

RECEIVER

1	

Switch on your system components and receiver.

Start by switching on the playback component (for example a DVD player), your TV and subwoofer (if you have
one), then the receiver (press u RECEIVER).
Make sure that the TV’s video input is set to this receiver.

2	

Select the input function you want to play.

You can use the input function buttons on the remote control, INPUT SELECT, or the front panel
INPUT SELECTOR dial.
!	 If you need to manually switch the input signal type press SIGNAL SEL (page 50).

3	Press

to the receiver operation mode.

4	 Press AUTO/ALC/DIRECT (AUTO SURR/ALC/STREAM DIRECT) to select ‘AUTO SURROUND’
and start playback of the source.
If you’re playing a Dolby Digital or DTS surround sound source, you should hear surround sound. If you are playing a stereo source, you will only hear sound from the front left/right speakers in the default listening mode.
!	 You may need to check the digital audio output settings on your DVD player or digital satellite receiver. It
should be set to output Dolby Digital, DTS and 88.2 kHz / 96 kHz PCM (2 channel) audio, and if there is an
MPEG audio option, set this to convert the MPEG audio to PCM.
!	 See also Listening to your system on page 48 for information on different ways of listening to sources.
It is possible to check on the front panel display whether or not multi-channel playback is being performed properly. For details, see Auto Surround, ALC and Stream Direct with different input signal formats on page 101.
When using surround speakers, 2DIGITAL is displayed when playing Dolby Digital 5.1 channel signals, and DTS
is displayed when playing DTS 5.1-channel signals.
If the display does not correspond to the input signal and listening mode, check the connections and settings.

5	

Use the VOLUME +/– to adjust the volume level.

Turn down the volume of your TV so that all sound is coming from the speakers connected to this receiver.

Note
!	 The playback operation can be performed on the OSD screen for certain inputs, but the OSD screen is only
displayed when the receiver and TV are connected with an HDMI cable. If the receiver and TV are connected
with anything other than an HDMI cable, perform the various operations while watching the front panel.

42

　
　
　
　

05

Basic playback

Playing an iPod

Note
!	 You can play all of the songs in a particular category by selecting the All item at the top of each category list.
For example, you can play all the songs by a particular artist.

This receiver has the iPod iPhone iPad USB terminal that will allow you to control playback of audio content from
your iPod using the controls of this receiver.
Here we describe the procedure for playback on an iPod. For playback on a USB device, see Playing a USB device
on page 44.

Basic playback controls
This receiver’s remote control buttons can be used for basic playback of files stored on an iPod.
!	Press iPod USB to switch the remote control to the iPod/USB operation mode.

Important
!	 This receiver is compatible with the audio and video of the iPod nano 3G/4G/5G/6G (audio only for the iPod
nano 6G), iPod touch 1G/2G/3G/4G, iPhone, iPhone 3G, iPhone 3GS, iPhone 4, iPhone 4S, iPad and iPad 2.
However, some of the functions may be restricted for some models.
!	 This receiver has been developed and tested for the software version of iPod/iPhone/iPad indicated on the
website of Pioneer (http://pioneer.jp/homeav/support/ios/na/).
!	 Installing software versions other than indicated on the website of Pioneer to your iPod/iPhone/iPad may result
in incompatibility with this receiver.
!	 iPod, iPhone and iPad are licensed for reproduction of non-copyrighted materials or materials the user is
legally permitted to reproduce.
!	 Features such as the equalizer cannot be controlled using this receiver, and we recommend switching the
equalizer off before connecting.
!	 Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from any
inconvenience or loss of recorded material resulting from the iPod failure.
!	 When listening to a track on the iPod in the main zone, it is possible to control the sub zone, but not to listen to
a different track in the sub zone from the one playing in the main zone.

DISP
TOP MENU

ENTER

RETURN

Switching the iPod controls
You can switch over the iPod controls between the iPod and the receiver.

1	

1	Press u RECEIVER to switch on the receiver and your TV.

2	

See Connecting an iPod on page 33.
About one minute is required between turning the power on and completion of startup.
!	 It is also possible to operate the iPod on the iPod itself, without using the TV screen. For details, see
Switching the iPod controls on page 43.

2	

Press iPod CTRL to switch the iPod controls.

This enables operation and display on your iPod, and this receiver’s remote control and GUI screen become
inactive.

Press iPod CTRL again to switch back to the receiver controls.
Note

!	 Change the receiver’s input to the iPod in one action by pressing the iPod iPhone iPad DIRECT CONTROL
button on the front panel to enable iPod operations on the iPod.

Press iPod USB on the remote control to switch the receiver to the iPod/USB.

When the display shows the names of folders and files, you’re ready to play music from the iPod.
!	 The controls of your iPod will be inoperable when connected to this receiver.

Playing back audio files stored on an iPod
To navigate songs on your iPod, you can take advantage of the GUI screen of your TV connected to this receiver.
You can also control all operations for music in the front panel display of this receiver.
!	 Note that characters that cannot be displayed on this receiver are displayed as #.
!	 This feature is not available for photos on your iPod. To display photos, switch iPod operation to the iPod (see
Switching the iPod controls on page 43).

Finding what you want to play
When your iPod is connected to this receiver, you can browse songs stored on your iPod by playlist, artist name,
album name, song name, genre or composer, similar to using your iPod directly.

1	Use i/j to select a category, then press ENTER to browse that category.
!	 To return to the previous level any time, press RETURN.

2	Use i/j to browse the selected category (e.g., albums).
!	Use k/l to move to previous/next levels.

3	 Continue browsing until you arrive at what you want to play, then press d to start
playback.
43

　
　
　
　

05

Basic playback

Playing back photo files stored on a USB memory device

Playing a USB device
It is possible to play files using the USB interface on the front of this receiver.
!	 Compatible USB devices include external magnetic hard drives, portable flash memory drives (particularly key
drives) and digital audio players (MP3 players) of format FAT16/32.
!	 Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and
assumes no responsibility for any loss of data that may occur when connected to this receiver.

!	 Photo files cannot be played in the sub zone.

1	Press u RECEIVER to switch on the receiver and your TV.

The selected content is displayed in full screen and a slideshow starts.

1	Use i/j to select a folder, then press ENTER to browse that folder.
!	 To return to the previous level any time, press RETURN.

2	 Continue browsing until you arrive at what you want to play, then press ENTER to start
playback.

See Connecting a USB device on page 33.
About one minute is required between turning the power on and completion of startup.
!	 Make sure the receiver is in standby when disconnecting the USB device.

2	

Basic playback controls
Button(s)

Press iPod USB on the remote control to switch the receiver to the iPod/USB.

When the display shows the names of folders and files, you’re ready to play from the USB device.

What it does

ENTER, d

Starts displaying a photo and playing a slideshow.

g

Stops the player and returns to the previous menu.

Note
If an Over Current message lights in the display, the power requirements of the USB device are too high for this
receiver. Try following the points below:
!	 Switch the receiver off, then on again.
!	 Reconnect the USB device with the receiver switched off.
!	 Use a dedicated AC adapter (supplied with the device) for USB power.
If this doesn’t remedy the problem, it is likely your USB device is incompatible.

Tip
!	 Slideshows of photo files can be played while listening to music files by returning to the folder/file list display
while playing a music file on a USB device then playing the photo files.

Playing back audio files stored on a USB memory device
The maximum number of levels that you can select in Step 1 (below) is 9.
!	 Note that non-Roman characters in the playlist are displayed as #.

1	Use i/j to select a folder, then press ENTER to browse that folder.
!	 To return to the previous level any time, press RETURN.

2	 Continue browsing until you arrive at what you want to play, then press d to start
playback.
!	 Copyrighted audio files cannot be played back on this receiver.
!	 DRM-protected audio files cannot be played back on this receiver.

Basic playback controls
This receiver’s remote control buttons can be used for basic playback of files stored on USB memory devices.
!	Press iPod USB to switch the remote control to the iPod/USB operation mode.
DISP
TOP MENU

ENTER

RETURN

44

　
　
　
　

05

Basic playback

About playable file formats

Listening to the radio

The USB function of this receiver supports the following file formats. Note that some file formats are not available
for playback although they are listed as playable file formats.

The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and
manual (step) tuning functions. If you already know the frequency of the station you want, see Tuning directly to a
station below. Once you are tuned to a station you can memorize the frequency for recall later-see Saving station
presets on page 45 for more on how to do this.

Music files
Category

MP3


Extension

.mp3

WAV

.wav

WMA

.wma

.m4a 
.aac
.3gp
.3g2

AAC

FLAC


.flac

Stream

MPEG-1 Audio Layer-3

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate

16 bit

Channel

2 ch

Bitrate

8 kbps to 320 kbps

VBR/CBR

Supported/Supported

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz

Quantization bitrate

16 bit, 24 bit

LPCM

WMA2/7/8/9


MPEG-4 AAC LC
MPEG-4 HE AAC
(aacPlus v1/2)

Channel

2 ch

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate

16 bit

Channel

2 ch

Bitrate

5 kbps to 320 kbps

VBR/CBR

Supported/Supported

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate

16 bit

Channel

2 ch

.jpg

Use BAND to change the band (FM or AM), if necessary.

3	

Tune to a station.

Improving FM sound
If the TUNED or STEREO indicator doesn’t light when tuning to an FM station because the signal is weak, press
MPX to switch the receiver into mono reception mode. This should improve the sound quality and allow you to
enjoy the broadcast.

Using the noise cut mode
The two noise cut modes can be used when receiving AM broadcasts. Press MPX to select the noise cut mode (1
to 2).

Bitrate

16 kbps to 320 kbps
Supported/Supported

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz

1	

Press TUNER to select the tuner.

2	

Use BAND to change the band (FM or AM), if necessary.

Quantization bitrate

16 bit, 24 bit

3	

Press D.ACCESS (Direct Access).

Channel

2 ch

4	

Use the number buttons to enter the frequency of the radio station.

Tuning directly to a station

For example, to tune to 106.00 (FM), press 1, 0, 6, 0, 0.
If you make a mistake halfway through, press D.ACCESS twice to cancel the frequency and start over.

Saving station presets
If you often listen to a particular radio station, it’s convenient to have the receiver store the frequency for easy
recall whenever you want to listen to that station. This saves the effort of manually tuning in each time. This
receiver can memorize up to 63 stations, stored in seven banks, or classes (A to G) of 9 stations each.

Photo files

JPEG

2	

VBR/CBR

FLAC

Extension

Press TUNER to select the tuner.

There are three ways to do this:
!	 Automatic tuning – To search for stations in the currently selected band, press and hold TUNE +/– for about
a second. The receiver will start searching for the next station, stopping when it has found one. Repeat to
search for other stations.
!	 Manual tuning – To change the frequency one step at a time, press TUNE +/–.
!	 High speed tuning – Press and hold TUNE +/– for high speed tuning. Release the button at the frequency
you want.

a	 “MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson multimedia.”
b	 Files encoded using Windows Media Codec 9 may be playable but some parts of the specification are not supported; specifically, Pro, Lossless, Voice.
c	 Apple lossless encoding is not supported.
d	 Uncompressed FLAC files are not supported. Pioneer does not guarantee playback.

Category

1	

Format

1	

Meeting the following conditions:
!	 Baseline JPEG format
!	 Y:Cb:Cr – 4:2:2

Tune to a station you want to memorize.

See Listening to the radio on page 45 for more on this.

2	

Press TOOLS (TUNER EDIT).

The display shows PRESET MEMORY, then a blinking memory class.

3	 Press CLASS to select one of the seven classes, then press PRESET +/– to select the station
preset you want.
You can also use the number buttons to select a station preset.

45

　
　
　
　

05
4	

Basic playback

Press ENTER.

Bluetooth ADAPTER for Wireless Enjoyment of Music

After pressing ENTER, the preset class and number stop blinking and the receiver stores the station.

Listening to station presets
1	

Press TUNER to select the tuner.

2	

Press CLASS to select the class in which the station is stored.

Bluetooth wireless
technology enabled device:
cell phone

Press repeatedly to cycle through classes A to G.

3	

Bluetooth wireless
technology enabled device:
Digital music player

Device not equipped with
Bluetooth wireless technology:
Digital music player
+
Bluetooth audio transmitter
(sold commercially)

Press PRESET +/– to select the station preset you want.

!	 You can also use the number buttons on the remote control to recall the station preset.

Naming station presets
For easier identification, you can name your station presets.

1	

Choose the station preset you want to name.

Music data

See Listening to station presets on page 46 for how to do this.

2	

Press TOOLS (TUNER EDIT).

This receiver

The display shows PRESET NAME, then a blinking cursor at the first character position.

3	

Bluetooth®
ADAPTER

Remote control
operation

Input the name you want.

Use TUNE +/– (or TUNE i/j of front panel) to select a character, PRESET +/– (or PRESET k/l of front panel) to
set the position, and ENTER to confirm your selection.

!	 About one minute is required between turning the power on and completion of startup.

Note
!	 To erase a station name, simply repeat steps 1 to 3 and input eight spaces instead of a name.
!	 Once you have named a station preset, you can press DISP when listening to a station to switch the display
between name and frequency.

Wireless music play
When the Bluetooth ADAPTER (AS-BT100 or AS-BT200) is connected to this unit, a product equipped with
Bluetooth wireless technology (portable cell phone, digital music player, etc.) can be used to listen to music wirelessly. Also, by using a commercially available transmitter supporting Bluetooth wireless technology, you can
listen to music on a device not equipped with Bluetooth wireless technology. The AS-BT100 and AS-BT200 models
supports SCMS-T contents protection, so music can also be enjoyed on devices equipped with SCMS-T type
Bluetooth wireless technology.
!	 The Air Jam function cannot be used with the AS-BT100.

Remote control operation
The remote control supplied with this unit allows you to play and stop media, and perform other operations.
!	 It must be necessary that the Bluetooth wireless technology enabled device supports AVRCP profiles.
!	 Remote control operations cannot be guaranteed for all Bluetooth wireless technology enabled devices.

Pairing the Bluetooth ADAPTER and Bluetooth wireless technology device
“Pairing” must be done before you start playback of Bluetooth wireless technology content using the Bluetooth
ADAPTER. Make sure to perform pairing the first time you operate the system or any time pairing data is cleared.
The pairing step is necessary to register the Bluetooth wireless technology device to enable Bluetooth communications. For more details, see also the operating instructions of your Bluetooth wireless technology device.
!	 Pairing is required when you first use the Bluetooth wireless technology device and Bluetooth ADAPTER.
!	 To enable Bluetooth communication, pairing should be done with both your system and Bluetooth wireless
technology device.

46

　
　
　
　

05

Basic playback

!	 If the Bluetooth wireless technology device’s security code is “0000”, there is no need to make the security code
setting on the receiver. Press ADPT to set the ADAPTER PORT input, then conduct the pairing operation on
the Bluetooth wireless technology device. If pairing is successful, there is no need to performing the pairing
operation below.
!	 When using the AS-BT200 only: This unit complies with Bluetooth Specifications Ver. 2.1. When this unit and
another device equipped with Bluetooth wireless technology both comply with Bluetooth Specification Ver. 2.1,
pairing of the two may be possible without the need for inputting a password.
In this case, a passcode may be displayed on this receiver and on the device equipped with Bluetooth wireless technology. If this happens, check that the same passcode is displayed on this receiver and the device
equipped with Bluetooth wireless technology, then press ENTER. After this, also perform the connection
operation on the Bluetooth device to be connected. If the passcode does not match the code displayed on the
Bluetooth device to be connected, press RETURN to cancel pairing, then try starting over.
Press ADPT to set the ADAPTER PORT input, then conduct the pairing operation on the Bluetooth wireless
technology device. If pairing is successful, there is no need to performing the pairing operation below.
!	 Pair one unit at a time.
!	 When connecting this receiver by Bluetooth connections with a device equipped with the Bluetooth function to
listen to music, do not connect any devices other than this receiver by Bluetooth connection to the Bluetoothequipped device. If a Bluetooth connection is already established with a device other than this receiver, disconnect the other device before connecting this receiver.

1	

Press ADPT on the remote control to switch the receiver to ADAPTER PORT input.

2	

Press TOP MENU to select Bluetooth Setup.

Listening to music contents of a Bluetooth wireless technology device with
your system
1	

Press ADPT on the remote control to switch the receiver to ADAPTER PORT input.

!	The ADAPTER PORT input can also be selected by pressing SOUND RETRIEVER AIR on the receiver. In this
case, the optimum listening mode (SOUND RETRIEVER AIR) is selected automatically.

2	 From the Bluetooth wireless technology device, perform the operation to connect to the
Bluetooth ADAPTER.
!	 When the Bluetooth ADAPTER is not plugged into the ADAPTER PORT, No Adapter will be displayed if
ADAPTER PORT input is selected.

3	

Start playback of music contents stored on the Bluetooth wireless technology device.

This receiver’s remote control buttons can be used for basic playback of files stored on Bluetooth wireless technology devices.
!	 Bluetooth wireless technology device should be compatible with AVRCP profile.
!	 Depending on the Bluetooth wireless technology device you use, operation may differ from what is shown in
the remote control buttons.

3	Use i/j to select ‘PIN’ then press ENTER.
4	Use i/j to select one of PIN codes 0000, 1234 or 8888, then press ENTER.
You can use any of 0000, 1234 or 8888 PIN codes. Bluetooth wireless technology device using any other PIN
code cannot be used with this receiver.

4	 While listening to a source, set the remote control to the receiver operation mode, then
press ADV SURR repeatedly to select SOUND RETRIEVER AIR.

5	 Switch on the Bluetooth wireless technology device that you want to make pair, place it
near the receiver and set it to the pairing mode.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by PIONEER CORPORATION is under license. Other trademarks and trade names are those of their
respective owners.

6	 Check to see that the Bluetooth ADAPTER is detected by the Bluetooth wireless technology
device.
When the Bluetooth wireless technology device is connected:
Bluetooth wireless technology device name appears in the receiver display.
!	 The system can display alphanumeric characters only. Other characters may not be displayed correctly.
When the Bluetooth wireless technology device is not connected:
No Device appears in the receiver display. In this case, perform the connection operation from the side of the
Bluetooth wireless technology device.

Air Jam
Air Jam - a Pioneer-exclusive application and available for free.
Air Jam lets you connect multi compatible devices to this unit using Bluetooth wireless technology. With it, you
can make a group playlist directly on a supported device to play in your home theater through the unit. You and
your friends can add songs from your devices to the playlist. Also Air Jam lets you delete the song before anyone
has to hear it.

7	 From the Bluetooth wireless technology device list, select Bluetooth ADAPTER and enter
the PIN code selected in step 4.
!	 The PIN code may in some cases be referred to as PASSKEY.

1	

Press ADPT on the remote control to switch the receiver to ADAPTER PORT input.

2	

Press TOP MENU to select Bluetooth Setup.

3	Use i/j to select ‘Air Jam’ then press ENTER.
4	Use i/j to select ‘Air Jam ON’ then press ENTER.
For more details of using Air Jam, access to our website.
http://pioneer.jp/product/soft/iapp_airjam/en.html

47

　
　
　
　

Listening to your system
Enjoying various types of playback using the listening modes................................................. 49
Selecting MCACC presets............................................................................................................... 50
Choosing the input signal.............................................................................................................. 50
Better sound using Phase Control................................................................................................. 51

48

　
　
　
　

06

Listening to your system

!	 2 PRO LOGIC – 4.1 channel surround sound (sound from the surround speakers is mono)
!	 2 Pro Logic IIz HEIGHT – Up to 7.1 channel sound (front height)
!	 WIDE SURROUND MOVIE – Up to 7.1 channel sound (front wide), especially suited to movie sources
!	 WIDE SURROUND MUSIC – Up to 7.1 channel sound (front wide), especially suited to music sources
!	 Neo:6 CINEMA – 7.1 channel sound (surround back), especially suited to movie sources
!	 Neo:6 MUSIC – 7.1 channel sound (surround back), especially suited to music sources
!	 STEREO – The audio is heard with your sound settings and you can still use the audio options.
With multichannel sources, if you have connected surround back, front height or front wide speakers, you can select
(according to format):
!	 2 Pro Logic IIx MOVIE – See above
!	 2 Pro Logic IIx MUSIC – See above
!	 Dolby Digital EX – Creates surround back channel sound for 5.1 channel sources and provides pure decoding for 6.1 channel sources (like Dolby Digital Surround EX)
!	 DTS-ES Matrix or DTS-ES Discrete – Allows you to hear 6.1 channel playback with DTS-ES encoded sources
!	 DTS Neo:6 – Allows you to hear 6.1 channel playback with DTS encoded sources
!	 Neo:6 – Allows you to hear 6.1 channel playback
!	 2 Pro Logic IIz HEIGHT – See above
!	 WIDE SURROUND MOVIE – See above
!	 WIDE SURROUND MUSIC – See above
!	 STEREO – See above
!	 Straight Decode – Plays back without the effects above.

Enjoying various types of playback using the listening modes
Using this receiver, you can listen to any source in surround sound. However, the options available will depend
on your speaker setup and the type of source you’re listening to.
To play with surround sound, check “Standard surround sound” or “Using the Advanced surround effects” below
and select the desired mode.
To play with the optimum mode for the input signal, see “Auto playback” or “Using Stream Direct”. (The sound is
played in stereo when 2-channel signals are input, in surround when multi-channel signals are input.)

Important
!	 The listening modes and many features described in this section may not be available depending on the current source, settings and status of the receiver.

Auto playback
There are many ways to listen back to sources using this receiver, but the simplest, most direct listening option
is the Auto Surround feature. The receiver automatically detects what kind of source you’re playing and selects
multichannel or stereo playback as necessary.

1	Press

to the receiver operation mode.

2	 While listening to a source, press AUTO/ALC/DIRECT (AUTO SURR/ALC/STREAM DIRECT) for
auto playback of a source.
AUTO SURROUND shows briefly in the display before showing the decoding or playback format. Check the digital format indicators in the front panel display to see how the source is being processed.
!	 If the source is Dolby Digital, DTS, or Dolby Surround encoded, the proper decoding format will automatically
be selected and shows in the display.
!	 When listening to the ADAPTER PORT input, the SOUND RETRIEVER AIR feature is selected automatically.
ALC – In the Auto level control (ALC) mode, this receiver equalizes playback sound levels.
Also, the low and high frequency sounds, dialogs, surround effects, etc., that are difficult to hear when the volume is low are adjusted to be optimal for the volume level. This mode is particularly optimum when listening at
night.

Note
!	 When listening sources in 2 Pro Logic IIz HEIGHT mode, you can also adjust the H.GAIN effect (see Setting
the Audio options on page 62).
!	 When listening to 2-channel sources in Dolby Pro Logic IIx Music mode, there are three further parameters
you can adjust: C.WIDTH,DIMENSION and PANORAMA. See Setting the Audio options on page 62 to adjust
them.
!	 When listening to 2-channel sources in Neo:6 Cinema or Neo:6 Music mode, you can also adjust the center
image effect (see Setting the Audio options on page 62).
!	 When listening through headphones, you can select STEREO mode only.

Using the Advanced surround effects

Note
!	When ALC is selected, the effect level can be adjusted using the EFFECT parameter in Setting the Audio
options on page 62.

The Advanced surround effects can be used for a variety of additional surround sound effects. Most Advanced
Surround modes are designed to be used with film soundtracks, but some modes are also suited for music
sources. Try different settings with various soundtracks to see which you like.

Standard surround sound

1	Press

The following modes provide basic surround sound for stereo and multichannel sources.

1	Press
2	

2	

to the receiver operation mode.

to the receiver operation mode.

Press ADV SURR (ADVANCED SURROUND) repeatedly to select a listening mode.

!	 ACTION – Designed for action movies with dynamic soundtracks
!	 DRAMA – Designed for movies with lots of dialog
!	 SCI-FI – Designed for science fiction with lots of special effects
!	 MONO FILM – Creates surround sound from mono soundtracks
!	 ENT.SHOW – Suitable for musical sources
!	 EXPANDED – Creates an extra wide stereo field
!	 TV SURROUND – Provides surround sound for both mono and stereo TV sources
!	 ADVANCED GAME – Suitable for video games
!	 SPORTS – Suitable for sports programs
!	 CLASSICAL – Gives a large concert hall-type sound
!	 ROCK/POP – Creates a live concert sound for rock and/or pop music

While listening to a source, press STANDARD (STANDARD SURROUND).

If necessary, press repeatedly to select a listening mode.
!	 If the source is Dolby Digital, DTS, or Dolby Surround encoded, the proper decoding format will automatically
be selected and shows in the display.
!	 If the surround back speakers are not connected, 2 Pro Logic IIx becomes 2 Pro Logic II (5.1 channel
sound).
With two channel sources, you can select from:
!	 2 Pro Logic IIx MOVIE – Up to 7.1 channel sound (surround back), especially suited to movie sources
!	 2 Pro Logic IIx MUSIC – Up to 7.1 channel sound (surround back), especially suited to music sources
!	 2 Pro Logic IIx GAME – Up to 7.1 channel sound (surround back), especially suited to video games

49

　
　
　
　

06

Listening to your system

!	 UNPLUGGED – Suitable for acoustic music sources
!	 EXT.STEREO – Gives multichannel sound to a stereo source, using all of your speakers
!	 F.S.SURR FOCUS – Use to provide a rich surround sound effect directed to the center of where the front left
and right speakers sound projection area converges.
!	 F.S.SURR WIDE – Use to provide a surround sound effect to a wider area than FOCUS mode.
FOCUS position
(Recommended)
Front left
speaker

Front right
speaker

Selecting MCACC presets
!	 Default setting: MEMORY 1
If you have calibrated your system for different listening positions, you can switch between settings to suit the
kind of source you’re listening to and where you’re sitting (for example, watching movies from a sofa, or playing a
video game close to the TV).

WIDE position
Front left
speaker

%	 While listening to a source, press MCACC.

Front right
speaker

Press repeatedly to select one of the six MCACC presets. See Data Management on page 81 to check and manage your current settings.
!	 These settings have no effect when headphones are connected.
!	 You can also press k/l to select the MCACC preset.

Choosing the input signal
On this receiver, it is possible to switch the input signals for the different inputs as described below.
!	 This receiver can only play back Dolby Digital, PCM (32 kHz to 192 kHz) and DTS (including DTS 96/24) digital
signal formats. The compatible signals via the HDMI terminals are: Dolby Digital, DTS, PCM (32 kHz to 192
kHz), Dolby TrueHD, Dolby Digital Plus, DTS-EXPRESS, DTS-HD Master Audio and SACD.
!	 You may get digital noise when an LD, CD, DVD or BD player compatible with DTS is playing an analog signal.
To prevent noise, make the proper digital connections (page 23) and set the signal input to DIGITAL.
!	 Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with
your DVD player.

!	 SOUND RETRIEVER AIR – Suitable for listening to the sound from a Bluetooth wireless technology device.
The SOUND RETRIEVER AIR listening mode can only be selected when the ADAPTER PORT input.
!	 PHONES SURR – When listening through headphones, you can still get the effect of overall surround.

Note
!	 When an Advanced Surround listening mode is selected, the effect level can be adjusted using the EFFECT
parameter in Setting the Audio options on page 62.
	 However, with F.S.SURR FOCUS, F.S.SURR WIDE and SOUND RETRIEVER AIR, the effect level cannot be
adjusted.
!	 The Front Stage Surround Advance (F.S.SURR FOCUS and F.S.SURR WIDE) function allows you to create natural surround sound effects using just the front speakers and the subwoofer.

1	Press
2	

Each press cycles through the options as follows:
!	 AUTO – The receiver selects the first available signal in the following order: HDMI; DIGITAL; ANALOG.
!	 ANALOG – Selects an analog signal.
!	 DIGITAL – Selects an optical or coaxial digital signal.
!	 HDMI – Selects an HDMI signal.
—	 When the HDMI audio output parameter is set to THROUGH, the sound will be heard through your TV, not
from this receiver.
When set to DIGITAL, HDMI or AUTO (only selected DIGITAL or HDMI), the indicators light according to the
signal being decoded (see Display on page 14).

Using Stream Direct
Use the Stream Direct modes when you want to hear the truest possible reproduction of a source. All unnecessary signal processing is bypassed, and you’re left with the pure analog or digital sound source.
Processing differs depending on the input signal and whether or not surround back speakers are connected. For
details, see Auto Surround, ALC and Stream Direct with different input signal formats on page 101.

1	Press

to the receiver operation mode.

Press SIGNAL SEL to select the input signal corresponding to the source component.

to the receiver operation mode.

2	 While listening to a source, press AUTO/ALC/DIRECT (AUTO SURR/ALC/STREAM DIRECT) to
select the mode you want.
Check the digital format indicators in the front panel display to see how the source is being processed.
!	 AUTO SURROUND – See Auto playback on page 49.
!	 ALC – Listening in Auto level control mode (page 49).
!	 DIRECT – Plays back sound from the source with the least modification next to PURE DIRECT. With DIRECT,
the only modifications added to PURE DIRECT playback are calibration of the sound field by the MCACC system and the Phase Control effect.
!	 PURE DIRECT – Plays back unmodified sound from source with only minimal digital treatment.

Note
!	 When listening through headphones, you can select ALC or PURE DIRECT mode only.

50

　
　
　
　

06

Listening to your system

　
　
　
　

Better sound using Phase Control
This receiver’s Phase Control feature uses phase correction measures to make sure your sound source arrives at
the listening position in phase, preventing unwanted distortion and/or coloring of the sound.
Phase Control technology provides coherent sound reproduction through the use of phase matching for an optimal sound image. The default setting is on and we recommend leaving Phase Control switched on for all sound
sources.

%	 Press PHASE (PHASE CONTROL) to switch on phase correction.
The PHASE CONTROL indicator on the front panel lights.

Note
!	 Phase matching is a very important factor in achieving proper sound reproduction. If two waveforms are ‘in
phase’, they crest and trough together, resulting in increased amplitude, clarity and presence of the sound
signal. If a crest of a wave meets a trough, then the sound will be ‘out of phase’ and an unreliable sound image
will be produced.
!	 For discs created with standards other than Phase Control, the LFE channel is delayed upon recording in the
first place. Phase Control Plus function corrects for phase shifting on such discs. For instructions on setting
the Phase Control Plus, see Setting the Audio options on page 62.
!	 If your subwoofer has a phase control switch, set it to the plus (+) sign (or 0º). However, the effect you can
actually feel when PHASE CONTROL is set to ON on this receiver depends on the type of your subwoofer. Set
your subwoofer to maximize the effect. It is also recommended you try changing the orientation or the place of
your subwoofer.
!	 Set the built-in lowpass filter switch of your subwoofer to off. If this cannot be done on your subwoofer, set the
cutoff frequency to a higher value.
!	 If the speaker distance is not properly set, you may not have a maximized PHASE CONTROL effect.
!	The PHASE CONTROL mode cannot be set to ON in the following cases:
—	When headphones are plugged in.
—	When the PURE DIRECT mode is switched on.
—	When the HDMI audio output parameter is set to THROUGH in Setting the Setting the Audio options on page
62.

51

Playback with NETWORK features
Introduction.................................................................................................................................... 53
Playback with Network functions................................................................................................. 54
About network playback............................................................................................................... 55
About playable file formats........................................................................................................... 57

52

　
　
　
　

07

Playback with NETWORK features

Using AirPlay on iPod touch, iPhone, iPad, and iTunes

Introduction

AirPlay works with iPhone 4S, iPhone 4, iPhone 3GS, iPod touch (4th, 3rd and 2nd generations), iPad 2, iPad with
iOS 4.2 or later, and iTunes 10.1 (Mac and PC) or later.
To use AirPlay, select your receiver on your iPod touch, iPhone, iPad or in iTunes. *1
The receiver’s input will switch automatically to AirPlay when AirPlay is in use. *2
The following operations can be performed when in AirPlay mode:
!	 Adjustment of the receiver’s volume from iPod touch, iPhone, iPad or iTunes.
!	 Pause/resume, next/previous track, and shuffle/repeat from the remote control of the receiver.
!	 Display of the currently playing track information on the receiver’s display, including artist, song and album
name.
*1: For more information, see the Apple website (http://www.apple.com).
*2: The receiver’s power automatically turns on when Network Standby at Network Setup is set to ON.

This receiver is equipped with the LAN terminal and you can enjoy the following features by connecting your
components to these terminals.

Listening to Internet radio stations
You can select and listen to your favorite Internet radio station from the list of Internet radio stations created,
edited, and managed by the vTuner database service exclusively for use with the Pioneer products.
dSee Playback with Network functions on page 54 and Listening to Internet radio stations on page 54.

Playback the music files stored in PCs
You can playback a lot of musics stored in your PCs using this unit.
!	 Besides a PC, you can also play back audio files stored on your other components with the built-in media
server function based on DLNA 1.0 or DLNA 1.5 framework and protocols (i.e. network-capable hard disks and
audio systems).
dSee Playback with Network functions on page 54 and Playing back audio files stored on components on the
network on page 55.

Note
!	 A network environment is required to use AirPlay.
!	 The receiver’s name that shows up in the AirPlay UI on iPod touch, iPhone, iPad and iTunes can be changed by
Friendly Name from Network Setup.
!	 AirPlay provided on this receiver has been developed and tested based on the software versions for the iPod,
iPhone, iPad and the software versions for iTunes that are indicated on the Pioneer website. AirPlay may not
be compatible with iPod, iPhone, iPad or iTunes software versions other than those indicated on the Pioneer
website.

Listening to SiriusXM or Pandora
dSee Listening to SiriusXM Internet Radio on page 55.
dSee Listening to Pandora Internet Radio on page 55.

Note
!	 To listen to Internet radio stations, you must sign a contract with an ISP (Internet Service Provider) beforehand.
!	 Photo or video files cannot be played back.
!	 With Windows Media Player 11 or Windows Media Player 12, you can even play back copyrighted audio files on
this receiver.

About the DHCP server function
To play back audio files stored on components on the network or listen to Internet radio stations, you must turn
on the DHCP server function of your router. In case your router does not have the built-in DHCP server function,
it is necessary to set up the network manually. Otherwise, you cannot play back audio files stored on components
on the network or listen to Internet radio stations. See Network Setup menu on page 86 for more on this.

About playable DLNA network devices
This unit allows you to play music on media servers connected on an identical Local Area Network (LAN) as the
receiver. This unit allows for the playing of files stored on the following devices:
!	 PCs running Microsoft Windows Vista or XP with Windows Media Player 11 installed
!	 PCs running Microsoft Windows 7 with Windows Media Player 12 installed
!	 DLNA-compatible digital media servers (on PCs or other components)
Files stored in a PC or DMS (Digital Media Server) as described above can be played via command from an external Digital Media Controller (DMC). Devices controlled by this DMC to play files are called DMRs (Digital Media
Renderers). This receiver supports this DMR function. When in the DMR mode, such operations as playing and
stopping files can be performed from the external controller. Volume adjustment and the muting control are also
possible. The DMR mode is canceled if the remote control unit is operated while in the DMR mode (aside from
certain buttons, including the VOLUME +/–, MUTE and DISP).
!	 Depending on the external controller being used, playback may be interrupted when the volume is adjusted
from the controller. In this case, adjust the volume from the receiver or remote control.

Authorizing this receiver
This receiver must be authorized to enable playback. This happens automatically when the receiver makes a
connection over the network to the PC. If not, please authorize this receiver manually on the PC. The authorization
(or permission) method for access varies depending on the type of server currently being connected. For more
information on authorizing this receiver, refer to the instruction manual of your server.

53

　
　
　
　

07

Playback with NETWORK features

Listening to Internet radio stations

Playback with Network functions

Internet radio is an audio broadcasting service transmitted via the Internet. There are a large number of Internet
radio stations broadcasting a variety of services from every corner of the world. Some are hosted, managed,
and broadcast by private individuals while others are by the corresponding traditional terrestrial radio stations
or radio networks. Whereas terrestrial, or OTA (over-the-air), radio stations are geographically restricted on the
range of radio waves broadcast from a transmitter through the air, Internet radio stations are accessible from
anywhere in the world, as long as there is a connection to the Internet, as services are not transmitted through
the air but are delivered over the World Wide Web. On this receiver you can select Internet radio stations by genre
as well as by region.
Depending on the Internet line conditions, the sound may not be smooth when playing Internet radio.

Important
!	 About one minute is required between turning the power on and completion of startup.
!	 When you play back audio files, ‘Connecting...’ is displayed before playback starts. The display may continue
for several seconds depending on the type of file.
!	 In case a domain is configured in a Windows network environment, you cannot access a PC on the network
while you are logged onto the domain. Instead of logging onto the domain, log onto the local machine.
!	 There are cases where the time elapsed may not be correctly displayed.

1	

Press NET repeatedly to select the category you want to play back.

About list of Internet radio

It may take several seconds for this receiver to access the network.
Select a category from the following list:
!	 INTERNET RADIO – Internet radio
!	 SiriusXM – Internet radio that supports SiriusXM
!	 PANDORA – Internet radio that supports Pandora
!	 MEDIA SERVER – Server components on the network
!	 FAVORITES – Favorite songs currently being registered
Depending on the selected category, the names of folders, files, and Internet radio stations are displayed.

The list of Internet radio stations on this receiver is created, edited, and managed by the vTuner database service
exclusively for use with this receiver. For details about vTuner, see vTuner on page 105.

Saving and retrieving Internet radio stations
You can easily save and retrieve saved Internet radio stations. See Playing back your favorite songs on page 55 for
more on this.
!	 To listen to Internet radio stations, you must have high-speed broadband Internet access. With a 56 K or ISDN
modem, you may not enjoy the full benefits of Internet radio.
!	 The port number varies depending on the Internet radio station. Check the firewall settings.
!	 A list of Internet radio stations provided by the vTuner database service is subject to change or deletion without
notice due to various reasons.
!	 Broadcasts may be stopped or interrupted depending on the Internet radio station. In this case, you cannot
listen to a radio station selected from the list of Internet radio stations.

2	Use i/j to select the folder, music files or Internet radio station to play back, and then
press ENTER.
Press i/j to scroll up and down the list and select the desired item. When you press ENTER, playback starts
with the playback screen being displayed for the selected item. To return to the list screen, press RETURN.
When the list screen is displayed from the playback screen, the playback screen reappears automatically if no
operation is performed for 10 seconds while the list screen is displayed.
Only audio files with the mark can be played. In case of the folders with the mark, use i/j and ENTER to
select the desired folder and audio files.

3	

Registering broadcast stations not on the vTuner list from the special Pioneer site
With the receiver, broadcast stations not included on the list of station distributed by vTuner can be registered
and played. Check the access code required for registration on the receiver, use this access code to access the
special Pioneer Internet radio site and register the desired broadcast stations in your favorites. The address of the
special Pioneer Internet radio site is:
http://www.radio-pioneer.com

Repeat step 2 to play back the desired song.

For detailed operating instructions, refer to the section shown below.
!	 Internet radio stations – See Listening to Internet radio stations on page 54.
!	 SiriusXM – See Listening to SiriusXM Internet Radio on page 55.
!	 Pandora – See Listening to Pandora Internet Radio on page 55.
!	 Media server – See Playing back audio files stored on components on the network on page 55.
!	 Favorites – See Playing back your favorite songs on page 55.

1	

2	Use i/j to select ‘Help’, then press ENTER.

Basic playback controls

3	Use i/j to select ‘Get access code’, then press ENTER.

You can perform the following operations with the remote control of this receiver. Note that some buttons are not
available for operation depending on the category currently being played back.
!	Press NET to switch the remote control to the network operation mode.

The access code required for registration on the special Pioneer Internet radio site is displayed. Make a memo of
this address.
The following can be checked on the Help screen:
!	 Get access code – The access code required for registration on the special Pioneer Internet radio site is
displayed.
!	 Show Your WebID/PW – After registering on the special Pioneer Internet radio site, the registered ID and
password are displayed.
!	 Reset Your WebID/PW – Resets all the information registered on the special Pioneer Internet radio site.
When reset, all the registered broadcast stations are also cleared. If you want to listen to the same stations,
re-register after resetting.

+Favorite
TOP MENU

Display the Internet Radio list screen.

To display the Internet Radio list screen, perform step 1 at Playback with Network functions on page 54.

TOOLS
DISP
ENTER

RETURN
/ CLR

54

　
　
　
　

07

Playback with NETWORK features

4	 Access the special Pioneer Internet radio site from your computer and perform the
registration process.

Playing back your favorite songs
Up to 64 favorite tracks on the media server and/or Internet radio stations can be registered in the Favorites
folder. Note that only the audio files stored on components on the network can be registered.

http://www.radio-pioneer.com
Access the above site and use the access code in step 3 to perform user registration, following the instructions
on the screen.

Registering and deleting audio files and Internet radio stations in and from the
Favorites folder

5	 Register the desired broadcast stations as your favorites, following the instructions on the
computer’s screen.
Both broadcast stations not on the vTuner list and stations on the vTuner list can be registered. In this case they
are registered on the receiver as favorite broadcast stations and can be played.

1	

Press NET repeatedly to select the INTERNET RADIO or MEDIA SERVER.

2	

With the track or Internet radio station you want to register selected, press +Favorite.

The selected song or Internet radio station is then registered in the Favorite.

Listening to SiriusXM Internet Radio
Check the website below to listen to SiriusXM Internet Radio: http://www.siriusxm.com/internetradio
!	 You must have a registered account in order to listen to songs using SiriusXM Internet Radio.
	Select SiriusXM, then follow the instructions on the screen to make the account settings.
!	 If you want to check or change an account that has already been registered, press the TOOLS button on the
SiriusXM top page and display the account input screen, then check or change the account.
!	 Some functions may be changed at SiriusXM’s discretion.

Note
!	 To delete tracks or Internet radio stations that have been registered, set the input to FAVORITES, select the
track or station to be deleted, then press the CLR button.

About network playback
The network playback function of this unit uses the following technologies:

Note
!	 When disposing of the product, we recommend you reset it to delete the data. See Resetting the system on
page 68.

Windows Media Player
See Windows Media Player 11/Windows Media Player 12 on page 105 for more on this.

Listening to Pandora Internet Radio

Windows Media DRM

Pandora is personalized internet radio that is designed to help you discover new music you’ll love mixed in with
music you already know.
For details, check the website: http://www.pandora.com
!	 You must have a registered account in order to listen to songs using Pandora Internet Radio.
	Select PANDORA, then follow the instructions on the screen to make the account settings.
!	 As of February 2012, the Pandora service is only offered in the United States.
!	 Some functions may be changed at Pandora’s discretion.

Microsoft Windows Media Digital Rights Management (WMDRM) is a platform to protect and securely deliver
content for playback on computers, portable devices and network devices. This unit’s functions as a WMDRM 10
for networked devices. WMDRM protected content can only be played on media servers supporting WMDRM.
Content owners use WMDRM technology to protect their intellectual property, including copyrights. This device
uses WMDRM software to access WMDRM protected content. If the WMDRM software fails to protect the content,
content owners may ask Microsoft to revoke the software’s ability to use WMDRM to play or copy protected content.
Revocation does not affect unprotected content. When you download licenses for protected content, you agree that
Microsoft may include a revocation list with the licenses. Content owners may require you to upgrade WMDRM to
access their content. If you decline an upgrade, you will not be able to access content that requires the upgrade.
This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology
outside of this product is prohibited without a license from Microsoft.

Note
!	 When disposing of the product, we recommend you reset it to delete the data. See Resetting the system on
page 68.
Pandora®, the leading internet radio service, gives people music they love anytime, anywhere, through personalized
radio stations.

DLNA

Playing back audio files stored on components on the network
This unit allows you to play music on media servers connected on an identical Local Area Network (LAN) as the
receiver. This unit allows for the playing of files stored on the following devices:
!	 PCs running Microsoft Windows Vista or XP with Windows Media Player 11 installed
!	 PCs running Microsoft Windows 7 with Windows Media Player 12 installed
!	 DLNA-compatible digital media servers (on PCs or other components)

DLNA CERTIFIEDTM Audio Player
The Digital Living Network Alliance (DLNA) is a cross-industry organization of consumer electronics, computing industry and mobile device companies. Digital Living provides consumers with easy sharing of digital media
through a wired or wireless network in the home.

55

　
　
　
　

07

Playback with NETWORK features

The DLNA certification logo makes it easy to find products that comply with the DLNA Interoperability Guidelines.
This unit complies with DLNA Interoperability Guidelines v1.5.
When a PC running DLNA server software or other DLNA compatible device is connected to this player, some
setting changes of software or other devices may be required. Please refer to the operating instructions for the
software or device for more information.
DLNATM, the DLNA Logo and DLNA CERTIFIEDTM are trademarks, service marks, or certification marks of the Digital
Living Network Alliance.

About playback behavior over a network
!	 Playback may stall when the PC is switched off or any media files stored on it are deleted while playing content.
!	 If there are problems within the network environment (heavy network traffic, etc.) content may not be displayed
or played properly (playback may be interrupted or stalled). For best performance, a 100BASE-TX connection
between player and PC is recommended.
!	 If several clients are playing simultaneously, as the case may be, playback is interrupted or stalled.
!	 Depending on the security software installed on a connected PC and the setting of such software, network
connection may be blocked.
Pioneer is not responsible for any malfunction of the player and/or the NETWORK features due to communication error/malfunctions associated with your network connection and/or your PC, or other connected equipment.
Please contact your PC manufacturer or Internet service provider.
“Windows MediaTM” is a trademark of Microsoft Corporation.
This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a
license from Microsoft Licensing, Inc.
Microsoft®, Windows®7, Windows®Vista, Windows®XP, Windows®2000, Windows®Millennium Edition, Windows®98,
and WindowsNT® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/
or other countries.

Content playable over a network
!	 Even when encoded in a compatible format, some files may not play correctly.
!	 Movie or Photo files cannot be played back.
!	 There are cases where you cannot listen to an Internet radio station even if the station can be selected from a
list of radio stations.
!	 Some functions may not be supported depending on the server type or version used.
!	 Supported file formats vary by server. As such, files not supported by your server are not displayed on this unit.
For more information check with the manufacturer of your server.

Disclaimer for Third Party Content
ACCESS TO THIRD PARTY CONTENT SERVICES, INCLUDING ALL ASSOCIATED FEATURES AND
FUNCTIONALITIES, IS PROVIDED “AS IS,” “AS AVAILABLE” AND AT THE USER’S OWN RISK, WITHOUT
WARRANTY OF ANY KIND. PIONEER DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, IN CONNECTION
WITH ACCESS TO AND USE OF CONTENT SERVICES THROUGH THIS DEVICE, INCLUDING WITHOUT
LIMITATION WARRANTIES OF MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR
PURPOSE, AND NON-INFRINGEMENT. PIONEER DOES NOT GUARANTEE, REPRESENT, OR WARRANT
THAT CONTENT SERVICES WILL BE FREE FROM ERRORS, INTERRUPTION, LOSS, CORRUPTION, ATTACK,
VIRUSES, INTERFERENCE, HACKING, OR OTHER SECURITY INTRUSION, AND PIONEER DISCLAIMS ANY
LIABILITY IN CONNECTION WITH THE FOREGOING. PIONEER IS NOT LIABLE OR RESPONSIBLE FOR ANY
LOSS OR DAMAGE ARISING FROM ACCESS TO OR USE OF CONTENT. NO ORAL OR WRITTEN INFORMATION
OR ADVICE GIVEN BY PIONEER OR ITS CUSTOMER SERVICES REPRESENTATIVES WILL CREATE ANY SUCH
WARRANTY.
IN NO EVENT WILL PIONEER, ITS AFFILIATES, OR THEIR RESPECTIVE OFFICERS, DIRECTORS, OR EMPLOYEES
BE LIABLE IN CONNECTION WITH YOUR USE OF THIRD PARTY CONTENT SERVICES THROUGH THIS DEVICE
FOR PERSONAL INJURY OR SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY
KIND, INCLUDING WITHOUT LIMITATION DAMAGES FOR ATTORNEY’S FEES, LOST DATA OR LOST PROFITS,
REGARDLESS OF THE THEORY OF LIABILITY AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN NO EVENT WILL PIONEER’S TOTAL LIABILITY TO YOU FOR ALL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIRD PARTY CONTENT SERVICES (OTHER THAN AS MAY BE REQUIRED BY LAW
IN CASES INVOLVING PERSONAL INJURY) EXCEED $10.00. THE FOREGOING LIMITATIONS WILL APPLY EVEN
IF THE ABOVE REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IF ANY APPLICABLE AUTHORITY HOLDS ANY
PORTION OF THIS SECTION TO BE UNENFORCEABLE, THEN LIABILITY WILL BE LIMITED TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW.

56

　
　
　
　

07

Playback with NETWORK features

　
　
　
　

About playable file formats
The NETWORK feature of this receiver supports the following file formats. Note that some file formats are not
available for playback although they are listed as playable file formats. Also, the compatibility of file formats varies depending on the type of server. Check with your server to ensure the compatibility of file formats supported
by your server.
!	 Internet radio playback may be affected by the Internet communications environment, and in this case playback may not be possible even with the file formats listed here.

Music files
Category

MP3


WAV

WMA

AAC

FLAC


Extension

.mp3

.wav

.wma

.m4a
.aac
.3gp
.3g2

.flac

Stream

MPEG-1 Audio Layer-3

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate

16 bit

Channel

2 ch

Bitrate

8 kbps to 320 kbps

VBR/CBR

Supported/Supported

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz

Quantization bitrate

16 bit, 24 bit

LPCM

WMA2/7/8/9


MPEG-4 AAC LC
MPEG-4 HE AAC
(aacPlus v1/2)

Channel

2 ch

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate

16 bit

Channel

2 ch

Bitrate

5 kbps to 320 kbps

VBR/CBR

Supported/Supported

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate

16 bit

Channel

2 ch

Bitrate

16 kbps to 320 kbps

VBR/CBR

Supported/Supported

Sampling frequency

32 kHz, 44.1 kHz, 48 kHz,
88.2 kHz, 96 kHz, 176.4 kHz,
192 kHz

Quantization bitrate

16 bit, 24 bit

Channel

2 ch

FLAC

a	 “MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson multimedia.”
b	 Files encoded using Windows Media Codec 9 may be playable but some parts of the specification are not supported; specifically, Pro, Lossless, Voice.
c	 Uncompressed FLAC files are not supported. Pioneer does not guarantee playback.

57

Control with HDMI function
About the Control with HDMI function........................................................................................ 59
Making Control with HDMI connections...................................................................................... 59
HDMI Setup..................................................................................................................................... 59
Before using synchronization........................................................................................................ 59
About synchronized operations.................................................................................................... 60
Setting the PQLS function.............................................................................................................. 60
About Sound Retriever Link and Stream Smoother Link............................................................ 60
Cautions on the Control with HDMI function.............................................................................. 60

58

　
　
　
　

08

Control with HDMI function

4	

About the Control with HDMI function

Select the ‘Control’ setting you want.

Choose whether to set this unit’s Control with HDMI function ON or OFF. You will need to set it to ON to use the
Control with HDMI function.
When using a component that does not support the Control with HDMI function, set this to OFF.
!	 ON – Enables the Control with HDMI function. Set Control Mode, ARC and PQLS in the subsequent setting
items to the desired values.
	 Also, by setting this to ON, the Sound Retriever Link and Stream Smoother Link functions can be operated
automatically by connecting a player supporting the respective functions. See Setting the Audio options
on page 62 for details on Sound Retriever Link, Setting the Video options on page 64 for details on Stream
Smoother Link.
!	 OFF – The Control with HDMI is disabled. The Control Mode, ARC and PQLS functions in the subsequent
setting items cannot be used.

Synchronized operations below with a Control with HDMI-compatible Pioneer TV or Blu-ray Disc player are possible when the component is connected to the receiver using an HDMI cable.
!	 The receiver’s volume can be set and the sound can be muted using the TV’s remote control.
!	 The receiver’s input switches over automatically when the TV’s input is changed or a Control with HDMIcompatible component is played.
!	 The receiver’s power is also set to standby, when the TV’s power is set to standby.

Important
!	 With Pioneer devices, the Control with HDMI functions are referred to as “KURO LINK”.
!	 You cannot use this function with components that do not support Control with HDMI.
!	 We only guarantee this receiver will work with Pioneer Control with HDMI-compatible components. However,
we do not guarantee that all synchronized operations will work with components that support the Control with
HDMI function.
!	 Use a High Speed HDMI® cable when you want to use the Control with HDMI function. The Control with
HDMI function may not work properly if a different type of HDMI cable is used.
!	 For details about concrete operations, settings, etc., refer to also the operating instructions for each
component.

5	

Select the ‘Control Mode’ setting you want.

Choose whether you want to enable synchronized operations.
!	 ON – Enabled for the synchronized operations.
!	 OFF – The synchronized operations disabled.

6	

Select the ‘ARC’ setting you want.

When a TV supporting the HDMI ARC (Audio Return Channel) function is connected to the receiver, the sound of
the TV can be input via the HDMI OUT terminal.
!	 ON – The TV’s sound is input via the HDMI terminal.
!	 OFF – The TV’s sound is input from the Audio input terminals other than HDMI inputs.

Making Control with HDMI connections

7	

You can use synchronized operation for a connected TV and other components.
!	 Be sure to connect the TV’s audio cable to the audio input of this unit. When the TV and receiver are connected
by HDMI connections, if the TV supports the HDMI ARC (Audio Return Channel) function, the sound of the TV
is input to the receiver via the HDMI OUT terminal, so there is no need to connect an audio cable. In this case,
set ARC at HDMI Setup to ON (see HDMI Setup on page 59).
For details, see Connecting your TV and playback components on page 25.

Select the ‘PQLS’ setting you want.

Choose whether to set this unit’s PQLS function AUTO or OFF.
For details about PQLS function, see Setting the PQLS function on page 60.
!	 AUTO – PQLS is enabled. A precision quartz controller in this receiver eliminates distortion caused by timing
errors (jitter), giving you the best possible digital-to-analog conversion when you use the HDMI interface. This
is valid as an HDMI function for PQLS-compatible players.
!	 OFF – PQLS is disabled.

8	
Important

Select the ‘Standby Through’ setting you want.

It is possible to transfer signals from an HDMI-connected player to the TV when this receiver’s power is on
standby.
Select the HDMI input whose HDMI signal is to be input for through transfer when in the standby mode. When
Last is selected, the signal being input to the currently selected HDMI input is transferred. When OFF is selected,
no HDMI input is transferred through when in the standby mode. (However, when Control is set to ON, the HDMI
signal is transferred through by the Control with HDMI function even when in the standby mode.)
!	 When anything other than OFF is set for this setting, the receiver’s HDMI input can be switched even when
the receiver is in the standby mode. (Switch by pointing the remote control at the receiver and pressing the
HDMI, BD, DVD, SAT/CBL or DVR/BDR button.)
!	 This setting can be used even with devices that are not compatible with the Control with HDMI function.
!	 Setting to anything other than “OFF” increases power consumption in the standby mode.

!	 When connecting this system or changing connections, be sure to switch the power off and disconnect the
power cord from the wall socket. After completing all connections, connect the power cords to the wall socket.
!	 After this receiver is connected to an AC outlet, a 2 second to 10 second HDMI initialization process begins.
You cannot carry out any operations during this process. The HDMI indicator in the front panel display blinks
during this process, and you can turn on this receiver once it has stopped blinking. When you set the Control
with HDMI to OFF, you can skip this process. For details about the Control with HDMI feature, see Control with
HDMI function on page 58.
!	 To get the most out of this function, we recommend that you connect your HDMI component not to a TV but
rather directly to the HDMI terminal on this receiver.

9	

HDMI Setup

When you’re finished, press HOME MENU.

You must adjust the settings of this receiver as well as the connected Control with HDMI-compatible components in order to make use of the Control with HDMI function. For more information see the operating instructions for each component.

Before using synchronization

1	Press

1	

Put all components into standby mode.

2	

Turn the power on for all components, with the power for the TV being turned on last.

Once you have finished all connections and settings, you must:

on the remote control, then press HOME MENU.

2	

Select ‘System Setup’, then press ENTER.

3	

Select ‘HDMI Setup’, then press ENTER.
59

　
　
　
　

08

Control with HDMI function

%	 Press PQLS to select the PQLS setting.

3	 Choose the HDMI input to which the TV is connected to this receiver, and see if video
output from connected components displays properly on the screen or not.
4	

The setting is displayed on the front panel display.
!	 PQLS AUTO – PQLS is enabled. A precision quartz controller in this receiver eliminates distortion caused by
timing errors (jitter), giving you the best possible digital-to-analog conversion when you use the HDMI interface. This is valid as an HDMI function for PQLS-compatible players.
!	 PQLS OFF – PQLS is disabled.

Check whether the components connected to all HDMI inputs are properly displayed.

About synchronized operations

About Sound Retriever Link and Stream Smoother Link

Important
!	 Synchronized operations are enabled when Control Mode is set to ON after setting Control in HDMI Setup to
ON. For details, see HDMI Setup on page 59.
The Control with HDMI-compatible component connected to the receiver operates in sync as described below.
!	 From the menu screen of the Control with HDMI-compatible TV, set audio to be played through this receiver,
and the receiver will switch to the synchronized amp mode.
!	 When in the synchronized amp mode, you can adjust the receiver’s volume or mute the sound using the TV’s
remote control.
!	 When in the synchronized amp mode, the synchronized amp mode is canceled when the receiver’s power is
turned off. To turn the synchronized amp mode back on, set audio to be played through the receiver from the
TV’s menu screen, etc. This receiver will power up and switch to the synchronized amp mode.
!	 When the synchronized amp mode is canceled, the receiver’s power turns off if you were viewing an HDMI
input or a TV program on the TV.
!	 When in the synchronized amp mode, the synchronized amp mode is canceled if an operation that produces
sound from the TV is performed from the TV’s menu screen, etc.
!	 When the TV’s power is set to standby, the receiver’s power is also set to standby. (Only when the input for a
component connected to the receiver by HDMI connection is selected or when watching the TV.)
!	 The receiver’s input switches automatically when the Control with HDMI-compatible component is played.
!	 The receiver’s input switches automatically when the TV’s input is switched.
!	 The synchronized amp mode remains in effect even if the receiver’s input is switched to a component other
than one connected by HDMI.
The operations below can also be used on Pioneer Control with HDMI-compatible TVs.
!	 When the receiver’s volume is adjusted or the sound is muted, the volume status is displayed on the TV’s
screen.
!	 When the OSD language is switched on the TV, the receiver’s language setting also switches accordingly.

These are automatic functions allowing you to output optimum audio and video signals from the receiver using
the Control with HDMI function. When a player supporting the respective function is connected to the receiver
by HDMI, the sound/picture is optimized for the compressed audio/video file played on the player.
!	 Depending on the compressed audio/video file format, it may not be operated automatically.

Sound Retriever Link
When playing a compressed audio file on the player, the file’s bitrate information is acquired using the Control
with HDMI function, and the sound is optimized on the receiver based on this information.
To activate the Sound Retriever Link function, make the setting below.

1	

Set the HDMI Setup’s Control to ON, and set the Control Mode setting to ON.

See HDMI Setup on page 59.

2	

Set the S.RTRV (Auto Sound Retriever) setting to ON.

See Setting the Audio options on page 62.

Stream Smoother Link
Using the Control with HDMI function, the receiver automatically detects whether a compressed video file is
being played on the player, and if so automatically activates the Stream Smoother function.
To activate the Stream Smoother Link function, make the setting below.

1	

Set the HDMI Setup’s Control to ON, and set the Control Mode setting to ON.

See HDMI Setup on page 59.

2	

Set the STREAM (Stream Smoother) setting to AUTO.

See Setting the Video options on page 64.

Setting the PQLS function

Cautions on the Control with HDMI function

PQLS (Precision Quartz Lock System) is a digital audio signal transfer control technology using the Control with
HDMI function. It offers higher-quality audio playback by controlling audio signals from the receiver to a PQLS
compatible player, etc. This enables removing jitter that has a negative effect on the quality of the sound and is
generated upon transmission.
!	 On players compatible with PQLS Bit-stream, PQLS always works for all sources.
!	 On players compatible with PQLS Multi Surround, PQLS works for all sources. Set the player’s audio output to
Linear PCM.
!	 On players compatible with PQLS 2 ch Audio, PQLS only works when playing CDs.
Please refer to the operating instructions supplied with your player for more information.
This function is activated when Control is set to ON.

!	 Connect the TV directly to this receiver. Interrupting a direct connection with other amps or an AV converter
(such as an HDMI switch) can cause operational errors.
!	 Only connect components (Blu-ray Disc player, etc.) you intend to use as a source to the HDMI input of this
receiver. Interrupting a direct connection with other amps or an AV converter (such as an HDMI switch) can
cause operational errors.
!	When Control is set to ON, HDMI Input in The Input Setup menu on page 39 is automatically set to OFF.
!	 When the receiver’s Control is turned ON, even if the receiver’s power is in the standby mode, it is possible
to output the audio and video signals from a player via HDMI to the TV without producing sound from the
receiver, but only when a Control with HDMI-compatible component (Blu-ray Disc player, etc.) and compatible
TV are connected. In this case, the receiver’s power turns on and the power and HDMI indicators light.

Tip
!	 The PQLS setting is set at PQLS in HDMI Setup on the HOME MENU, but the setting can also be switched
with the remote control, as described below.

60

　
　
　
　

Using other functions
Setting the Audio options............................................................................................................. 62
Setting the Video options.............................................................................................................. 64
Switching the speaker terminals................................................................................................... 66
Using the MULTI-ZONE controls.................................................................................................... 66
Making an audio or a video recording......................................................................................... 67
Network settings from a web browser........................................................................................ 67
Using the sleep timer..................................................................................................................... 67
Dimming the display...................................................................................................................... 67
Checking your system settings...................................................................................................... 67
Resetting the system...................................................................................................................... 68

61

　
　
　
　

09

Using other functions

Setting the Audio options
There are a number of additional sound settings you can make using the AUDIO PARAMETER menu. The
defaults, if not stated, are listed in bold.

Important

Setting

What it does

Option(s)
OFF

S.RTRV
(Auto Sound Retriever)


With the Auto Sound Retriever function, DSP processing is used to
compensate for the loss of audio data upon compression, improving
the sound’s sense of density and modulation.
Also, when a player supporting the Sound Retriever Link function is
connected to the receiver by HDMI, by setting this to ON, the bitrate
information of the compressed audio file being played on the player
is acquired using the Control with HDMI function, and the sound is
optimized based on this information (Sound Retriever Link).

DNR
(Digital Noise Reduction)

May improve the quality of sound in a noisy source (for example, video OFF
tape with lots of background noise) when switched on.
This only has an effect with 2-channel signal inputs.
ON
This mode is effective for contents with a sampling frequency of 48
kHz or less.

DIALOG E
(Dialog Enhancement)


Localizes dialog in the center channel to make it stand out from other
c OFF/FLAT/UP1/UP2/
background sounds in a TV or movie soundtrack. By moving from UP1
UP3/UP4 d
through UP2 and UP3 up to UP4, you can make the sound source
Default: OFF
seem to relocate upwards.

Hi-bit24

Creates a wider dynamic range with digital sources like CDs, DVDs or
BDs. 16- and 20-bit PCM as well as compressed audio is requantized
to 24 bits, and the high frequency component is interpolated upon
data processing to enable smoother, more subtle musical expression.
This mode is effective for contents with a sampling frequency of 48
kHz or less.

!	 Note that if a setting doesn’t appear in the AUDIO PARAMETER menu, it is unavailable due to the current
source, settings and status of the receiver.

1	Press

to the receiver operation mode, then press AUDIO PARAMETER.

2	Use i/j to select the setting you want to adjust.
Depending on the current status/mode of the receiver, certain options may not be able to be selected. Check the
table below for notes on this.

3	Use k/l to set as necessary.
See the table below for the options available for each setting.

4	

Press RETURN to confirm and exit the menu.

Audio parameter menu
Setting

What it does

Option(s)

MCACC
(MCACC preset)

Selects your favorite MCACC preset memory when multiple preset
memories are saved. When an MCACC preset memory has been
renamed, the given name is displayed.

c M1. MEMORY 1 to
M6. MEMORY 6 d
Default:
M1. MEMORY 1

EQ
(Acoustic Calibration EQ)

Switches on/off the effects of EQ Pro.

S-WAVE
(Standing Wave)

Switches on/off the effects of Standing Wave Control.

Phase C+
(Phase Control Plus)

For discs created with standards other than Phase Control, the LFE
channel is delayed upon recording in the first place. This function
corrects for phase shifting on such discs.
This function is especially effective when playing music.
When AUTO is selected, the LFE channel’s delay is measured automatically and the disc is played with the optimum correction.

c AUTO/0 to 16 (ms) d
Default: AUTO

DELAY
(Sound Delay)

Some monitors have a slight delay when showing video, so the
soundtrack will be slightly out of sync with the picture. By adding a
bit of delay, you can adjust the sound to match the presentation of
the video.

c 0.0 to 10.0 (frames) d
1 second = 30 frames
(NTSC)
Default: 0.0
BYPASS

TONE
(Tone Control)

Applies the treble and bass tone controls to a source, or bypasses
them completely.
This setting is only displayed when the listening mode is STEREO,
Auto surround (STEREO) or SOUND RETRIEVER AIR.

BASS


Adjusts the amount of bass.

c –6 to +6 (dB) d
Default: 0 (dB)

TREBLE


Adjusts the amount of treble.

c –6 to +6 (dB) d
Default: 0 (dB)

ON

ON

OFF

CH1 – Channel 1 is
heard only

ON
OFF

DUAL
(Dual Mono)

Specifies how dual mono encoded Dolby Digital soundtracks should
be played. Dual mono is not widely used, but is sometimes necessary
when two languages need to be sent to separate channels.

CH2 – Channel 2 is
heard only

OFF

Fixed PCM

This is useful if you find there is a slight delay before OFF recognizes
the PCM signal on a CD, for instance.
When ON is selected, noise may be output during playback of nonPCM sources. Please select another input signal if this is a problem.

DRC
(Dynamic Range Control)


Adjusts the level of dynamic range for movie soundtracks optimized
for Dolby Digital, DTS, Dolby Digital Plus, Dolby TrueHD, DTS-HD and
DTS-HD Master Audio (you may need to use this feature when listening to surround sound at low volumes).

Loud Mgmt
(Loudness Management)

Adjusts the level of dynamic range for movie soundtracks optimized
for Dolby TrueHD (you may need to use this feature when listening to
surround sound at low volumes).
This can only be set when DRC is set to OFF and the input signal is a
Dolby TrueHD signal.

LFE
(LFE Attenuate)

Some audio sources include ultra-low bass tones. Set the LFE attenuator as necessary to prevent the ultra-low bass tones from distorting
the sound from the speakers.
The LFE is not limited when set to 0 dB, which is the recommended
value. When set to –5 dB, –10 dB, –15 dB or –20 dB, the LFE is limited
by the respective degree. When OFF is selected, no sound is output
from the LFE channel.

ON
OFF

ON

62

CH1 CH2 – Both channels heard from front
speakers

ON
AUTO
MAX
MID
OFF
ON
OFF

c OFF/ –20dB/ –15dB/
–10dB/ –5dB/ 0dB d
Default: 0dB

　
　
　
　

09

Using other functions

Setting

What it does

Option(s)
OFF

A.ATT
(Analog input attenuate)

The input attenuator lowers the input level of an analog signal when
it’s too strong. You can use this if you find that the OVER indicator
lights often or you can hear distortion in the sound.
The attenuator isn’t available with digital sources, or when using the
Stream Direct (ANALOG DIRECT) modes.

SACD GAIN


Brings out detail in SACDs by maximizing the dynamic range (during
digital processing).

0dB

HDMI
(HDMI Audio)


Specifies the routing of the HDMI audio signal out of this receiver
(amp) or through to a TV. When THROUGH is selected, no sound is
output from this receiver.

AMP

OFF

A.DELAY
(Auto delay)


This feature automatically corrects the audio-to-video delay between
components connected with an HDMI cable. The audio delay time
is set depending on the operational status of the display connected
with an HDMI cable. The video delay time is automatically adjusted
according to the audio delay time.

C.WIDTH
(Center Width)
(Applicable only when using a
center speaker)


Provides a better blend of the front speakers by spreading the center
channel between the front right and left speakers, making it sound
wider (higher settings) or narrower (lower settings).

c 0 to 7 d
Default: 3

DIMENSION


Adjusts the depth of the surround sound balance from front to back,
making the sound more distant (minus settings), or more forward
(positive settings).

c –3 to +3 d
Default: 0

PANORAMA


Extends the front stereo image to include the surround speakers for a
‘wraparound’ effect.

C.IMAGE
(Center Image)
(Applicable only when using a
center speaker)


Adjusts the center image to create a wider stereo effect with vocals.
Adjust the effect from 0 (all center channel sent to front right and left
speakers) to 10 (center channel sent to the center speaker only).

c 0 to 10 d
Defaults:
Neo:6 MUSIC: 3
Neo:6 CINEMA: 10

EFFECT

Sets the effect level for the currently selected Advanced Surround or
ALC mode (each mode can be set separately).

c 10 to 90 d
Defaults:
EXT.STEREO: 90
Others: 50

H.GAIN
(Height Gain)

Adjusts the output from the front height speaker when listening in 2
Pro Logic IIz HEIGHT mode. If set to HIGH, the sound from the top
will be more emphasized.

LOW

V.SB
(Virtual Surround Back)


When you’re not using surround back speakers, selecting this mode
allows you to hear a virtual surround back channel through your surround speakers. You can choose to listen to sources with no surround
back channel information.

OFF

V.HEIGHT
(Virtual Height)


When you’re not using front height speakers, selecting this mode
allows you to hear a virtual front height channel through your front
speakers.

OFF

When you’re not using front wide speakers, selecting this mode
allows you to hear a virtual front wide channel through your front
speakers.
This improves the continuity of the sound from the front channel to
the surround channels.

OFF

V.WIDE
(Virtual Wide)


Setting

What it does

V.DEPTH
(Virtual Depth)


When this mode is selected, the sound field expands virtually to
behind the display, resulting in a sound field with the same depth as
the 3D picture to achieve a better sense of presence.

Option(s)
OFF

ON

MIN
MID
MAX

a	 The adjustment can be made only when TONE is set to ON.
b	 ! When ON is selected, the Sound Retriever effect is optimized based on the bitrate information of the contents input to the
USB memory audio and INTERNET RADIO, SiriusXM, PANDORA, MEDIA SERVER, FAVORITES (digital audio input only) to
achieve high sound quality.
	 ! With the iPod/USB, INTERNET RADIO, SiriusXM, PANDORA, MEDIA SERVER, FAVORITES or ADAPTER PORT input function, by default S.RTRV is set to ON.
	 ! When ON is selected, optimum correction of the audio signals input via the HDMI OUT terminal is conducted with the HDMI
ARC (Audio Return Channel) function, and the sound of digital TV broadcasts is produced with HD quality. This is valid when
the input is set to TV and ARC in HDMI Setup is set to ON. (See HDMI Setup on page 59.)
c	 UP1 to UP4 can be selected only when the front height speaker is connected. The presence or absence of effects depends on
the listening mode.
d	 The initially set AUTO is only available for Dolby TrueHD signals. Select MAX or MID for signals other than Dolby TrueHD.
e	 You shouldn’t have any problems using this with most SACD discs, but if the sound distorts, it is best to switch the gain setting
back to 0dB.
f	 ! The HDMI Audio setting cannot be switched while performing synchronized amp mode operations.
	 ! The synchronized amp mode must be turned on in order to play the receiver’s HDMI audio and video input signals from the TV
with the receiver’s power in the standby mode. See About synchronized operations on page 60.
g	 This feature is only available when the connected display supports the automatic audio/video synchronizing capability (‘lipsync’)
for HDMI. If you find the automatically set delay time unsuitable, set A.DELAY to OFF and adjust the delay time manually. For
more details about the lipsync feature of your display, contact the manufacturer directly.
h	 Only when listening to 2-channel sources in Dolby Pro Logic IIx Music/Dolby Pro Logic II Music mode.
i	 Only when listening to 2-channel sources in Neo:6 MUSIC/CINEMA mode.
j	 ! You can’t use the Virtual Surround Back mode when the headphones are connected to this receiver or when any of the stereo,
Front Stage Surround Advance, Sound Retriever Air or Stream Direct modes is selected.
	 ! You can only use the Virtual Surround Back mode if the surround speakers are on and the SB setting is set to NO or if Front
Bi-Amp or ZONE 2 is selected at Speaker System. It can also be used when Speaker B is selected at Speaker System and
SP:dA+B ON is selected with the SPEAKERS button.
	 ! This mode is effective for contents with a sampling frequency of 48 kHz or less.
k	 ! You can’t use the Virtual Height mode when the headphones are connected to this receiver or when any of the stereo, Front
Stage Surround Advance, Sound Retriever Air or Stream Direct modes is selected.
	 ! You can only use the Virtual Height mode if the surround speakers are on and the FH setting is set to NO. It can also not be
used when playing signals containing actual front height channel information.
	 ! This mode is effective for contents with a sampling frequency of 48 kHz or less.
l	 ! You can’t use the Virtual Wide mode when the headphones are connected to this receiver or when any of the stereo, Front
Stage Surround Advance, Sound Retriever Air or Stream Direct modes is selected.
	 ! You can only use the Virtual Wide mode if the surround speakers are on and the FW setting is set to NO. It can also not be
used when playing signals containing actual front wide channel information.
	 ! This mode is effective for contents with a sampling frequency of 48 kHz or less.
m	 ! This mode is effective for contents with a sampling frequency of 48 kHz or less.
	 ! You can’t use the Virtual Depth mode when the headphones are connected to this receiver or Stream Direct modes is
selected.

+6dB

THROUGH

ON

OFF
ON

MID
HIGH

ON

ON

ON

63

　
　
　
　

09

Using other functions

Setting the Video options
There are a number of additional picture settings you can make using the VIDEO PARAMETER menu. The
defaults, if not stated, are listed in bold.

Setting

What it does

V.ADJ
(Advanced Video Adjust)

Sets the optimum picture quality for the type of monitor that is connected. Select PDP for plasma displays, LCD for liquid crystal monitors, FPJ for front projectors, PRO for professional monitors. If you
want to adjust the picture quality settings to your personal tastes,
select MEMORY.

Important
!	 Note that if an option cannot be selected on the VIDEO PARAMETER menu, it is unavailable due to the current
source, setting and status of the receiver.
!	 All of the setting items can be set for each input function.
!	 Setting items other than V.CONV can only be selected when V.CONV is set to ON.

1	Press

Option(s)
PDP
LCD
FPJ
PRO
MEMORY

Reduces noise in the luminance (Y) signal.

YNR


to the receiver operation mode, then press VIDEO PARAMETER.

c

c 0 to +8 d
Default: 0

2	Use i/j to select the setting you want to adjust.
Depending on the current status/mode of the receiver, certain options may not be able to be selected. Check the
table below for notes on this.

d
(The image is only an example for checking the effect.)

3	Use k/l to set as necessary.

Reduces noise in the input’s color (C) signal.

See the table below for the options available for each setting.

4	

Press RETURN to confirm and exit the menu.

CNR


c

c 0 to +8 d
Default: 0

Video parameter menu
Setting

What it does

V.CONV
(Digital Video Converter)


Converts video signals for output from the HDMI OUT connector for
all video types (see page 24).

d
(The image is only an example for checking the effect.)

Option(s)
ON

Reduces block noise (block-shaped distortion generated upon MPEG
compression) in the picture.

OFF
AUTO

BNR


PURE
RES
(Resolution)


Specifies the output resolution of the video signal (when video input
signals are output at the HDMI OUT connector, select this according
to the resolution of your monitor and the images you wish to watch).
(“480p” indicates the 480p/576p resolution setting.)

480p
720p
1080p

Reduces mosquito noise (distortion generated at the contours of the
picture upon MPEG compression) in the picture.

1080/24p
This setting optimizes the operation of the progressive scanning circuit for playing film materials. Normally set it to AUTO. If the picture
seems unnatural, switch this to ON or OFF.

AUTO

P.MOTION
(Progressive Motion)


Adjusts the motion and still picture quality when video output is set
to progressive.

c –4 to +4 d
Default: 0
OFF

STREAM
(Stream Smoother)


This improves elements that reduce picture quality mainly noticeable
in network contents, such as mosquito noise and block noise.
When AUTO is selected, this unit’s Stream Smoother function
automatically turns on when network contents are played on the
player supporting Stream Smoother Link and connected to this unit
by HDMI (assuming that integrated operation with the Control with
HDMI function is set). (Stream Smoother Link)

c 0 to +8 d
Default: 0

d
(The image is only an example for checking the effect.)

1080i

PCINEMA
(PureCinema)


c

ON

MNR


OFF

c

c 0 to +8 d
Default: 0

d
(The image is only an example for checking the effect.)
Adjusts how sharp edges appear.

ON
DETAIL


AUTO

c

d
(The image is only an example for checking the effect.)

64

c 0 to +8 d
Default: 0

　
　
　
　

09
Setting

Using other functions

What it does

Option(s)

Adjusts the overall brightness.

c
BRIGHT
(Brightness)


0

Adjusts the contrast between light and dark.

c

0

c –6 to +6 d
Default: 0

d
(The image is only an example for checking the effect.)
Adjusts the red/green balance.

c
HUE


0

c –6 to +6 d
Default: 0

d
(The image is only an example for checking the effect.)
Adjusts saturation from dull to bright.

c
CHROMA
(Chroma Level)


0

c –6 to +6 d
Default: 0

d
(The image is only an example for checking the effect.)
BLK SETUP
(Black Setup)


Sets the black level according to the video input signal.
Normally select 7.5. If the dark parts of the picture are all black with
this setting, select 0.

What it does

Option(s)

ASP
(Aspect)


Specifies the aspect ratio when input signals are output at the HDMI
output. Make your desired settings while checking each setting on
your display (if the image doesn’t match your monitor type, cropping
or black bands appear).

THROUGH
NORMAL

a	 ! If the video picture deteriorates when this settings is switched ON, switch it OFF.
	 ! When connected to a video device using the component video input, set this setting to ON and watch with the HDMI output.
b	 ! When set to a resolution with which the TV (monitor) is not compatible, no picture is output. Also, in some cases no picture
will be output due to copyright protection signals. In this case, change the setting.
	 ! When AUTO is selected, the resolution is selected automatically according to the capacity of the TV (monitor) connected by
HDMI. When PURE is selected, the signals are output with the same resolution as when input (see About the video converter on
page 24).
c	 ! This setting is valid for HDMI output.
	 ! P.MOTION is disabled when PCINEMA is set to ON.
	 ! This setting have the effect only for pictures recorded in the interlaced scan format (480i/576i or 1080i signals).
d	 Adjustment is not possible unless V.ADJ (Advanced Video Adjust) is set to MEMORY.
e	 ! This setting is only displayed when the video signals below are being input:
—	480i, 576i, 480p, 576p, 720p, 1080i analog video signals
—	480i, 576i, 480p, 576p, 720p, 1080i, 1080p, 1080p24 HDMI video signals
f	 This adjustment is only possible when 480i signals are being input from the composite video jacks.
g	 ! If the image doesn’t match your monitor type, adjust the aspect ratio on the source component or on the monitor.
	 ! This setting is only displayed when 480i/p or 576i/p video signals are being input.

c –6 to +6 d
Default: 0

d
(The image is only an example for checking the effect.)

CONTRAST


Setting

7.5
0

65

　
　
　
　

09

Using other functions

Switching the speaker terminals

Using the MULTI-ZONE controls

If you selected Normal(SB/FH), Normal(SB/FW) or Speaker B at Speaker system setting on page 84, you can
switch between speakers using the SPEAKERS button. If you selected Front Bi-Amp or ZONE 2, the button will
simply switch your main speaker terminals on or off.

The following steps use the front panel controls to adjust the sub zone volume and select sources. See MULTIZONE remote controls on page 67.

1	Press

Each press selects a MULTI-ZONE option:
!	 ZONE 2 ON – Selects your primary (ZONE 2) sub zone
!	 ZONE 2&3 ON – Select both sub zones
!	 ZONE 3 ON – Selects your secondary (ZONE 3) sub zone
!	 MULTI ZONE OFF – Switches the MULTI-ZONE feature off
The MULTI-ZONE indicator lights when the MULTI-ZONE control has been switched ON.

2	

1	

to the receiver operation mode.

Use SPEAKERS to select a speaker system setting.

As mentioned above, if you have selected Front Bi-Amp or ZONE 2, the button will simply switch your main
speaker terminal (A) on or off.
Press repeatedly to choose a speaker terminal option:
When you select Normal(SB/FH), you can select from:
!	 SP: SB/FH ON – Surround back or front height channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. The surround back and front height
channels are switched automatically according to the audio input signal.
!	 SP: SB ON – Surround back channels are added to the front, center and surround channels (maximum 5
channels) and a maximum of 7 channels are output.
!	 SP: FH ON – Front height channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output.
!	 SP: OFF – No sound is output from the speakers (Pre-AMP mode).
When you select Normal(SB/FW), you can select from:
!	 SP: SB/FW ON – Surround back or front wide channels are added to the front, center and surround channels
(maximum 5 channels) and a maximum of 7 channels are output. The surround back and front wide channels
are switched automatically according to the audio input signal.
!	 SP: SB ON – Surround back channels are added to the front, center and surround channels (maximum 5
channels) and a maximum of 7 channels are output.
!	 SP: FW ON – Front wide channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output.
!	 SP: OFF – No sound is output from the speakers (Pre-AMP mode).
When you select Speaker B, you can select from:
!	 SP: A ON – Sound is output from the A-speaker terminals (up to 7 channels (including surround back channels), depending on the source).
!	 SP: B ON – Sound is output from the two speakers connected to the B-speaker terminals. Multichannel
sources will not be heard.
!	 SP: A+B ON – Sound is output from the A-speaker terminals (up to 5 channels, depending on the source), the
two speakers connected to the B-speaker terminals, and the subwoofer. The sound from the B-speaker terminals will be the same as the sound from the A-speaker terminals (multichannel sources will be downmixed to
2 channels).
!	 SP: OFF – No sound is output from the speakers (Pre-AMP mode).

2	

Press MULTI-ZONE ON/OFF on the front panel.

Press MULTI-ZONE CONTROL on the front panel to select the sub zone(s) you want.

If you selected ZONE 2&3 ON above, you can toggle between ZONE 2 and ZONE 3.
!	 When the receiver is on, make sure that any operations for the sub zone are done while ZONE and your
selected sub zone(s) show in the display. If this is not showing, the front panel controls affect the main zone
only.
	 If the receiver is in standby, the display is dimmed, and ZONE and your selected sub zone(s) continue to show
in the display.

3	

Use the INPUT SELECTOR dial to select the source for the zone you have selected.

For example, ZONE 2 DVD sends the source connected to the DVD inputs to the primary (ZONE 2) sub room.
!	 If you select TUNER, you can use the tuner controls to select a preset station (see Saving station presets
on page 45 if you’re unsure how to do this). The tuner cannot be tuned to more than one station at a time.
Therefore, changing the station in one zone also changes the station in the other zone. Please be careful not
to change stations when recording a radio broadcast.

4	

Use the MASTER VOLUME dial to adjust the volume for the sub zone.

When Speaker System is set to anything other than ZONE 2, the volume output from the receiver’s AUDIO
ZONE 2 OUT terminals can be fixed to –40 dB or 0 dB and the volume can be adjusted from the connected amplifier. If you want to adjust the volume from the connected amplifier, see ZONE Setup on page 89.

5	 When you’re finished, press MULTI-ZONE CONTROL again to return to the main zone
controls.
You can also press MULTI-ZONE ON/OFF on the front panel to switch off all output to the sub zone.
!	 You won’t be able to switch the main zone off completely unless you’ve switched off the MULTI-ZONE control
first.
!	 If you don’t plan to use the MULTI-ZONE feature for a while, turn off the power in both the sub and main
rooms so that this receiver is in standby.

Note
!	 The subwoofer output depends on the settings you made in Manual speaker setup on page 84. However, if SP:
B ON is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).
!	 All speaker systems (except Speaker B connections) are switched off when headphones are connected.

66

　
　
　
　

09

Using other functions

MULTI-ZONE remote controls

Network settings from a web browser

Press the remote control’s ZONE 2 or ZONE 3 to operate the corresponding zone.
The following table shows the possible MULTI-ZONE remote controls:

Network settings and Pandora or SiriusXM account settings can be made using the browser on a computer connected to the same LAN as the receiver.

Button(s)

What it does

u

Switches on/off power in the sub zone.

INPUT SELECT

Use to select the input function in the sub zone.

Input function buttons

Use to select the input function directly (this may not work for some functions) in the sub
zone.

For example, if the receiver’s address is 192.168.0.2, input “http://192.168.0.2/”. Check the receiver’s IP address at
Checking the Network Information on page 87.
When connected with the receiver, the Web Control screen appears in the browser.

VOLUME +/–


Use to set the listening volume in the sub zone.

3	

MUTE


Mutes the sound or restores the sound if it has been muted (adjusting the volume also
restores the sound).

to the receiver operation mode, then press SLEEP repeatedly to set the sleep
30 min

60 min

Off

90 min

Dimming the display
You can choose between four brightness levels for the front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.

%	Press
to the receiver operation mode, then press DIMMER repeatedly to change the
brightness of the front panel display.

Select the source you want to record.

!	 You can also choose to turn the display off. In this case, the FL OFF indicator lights.

Prepare the source you want to record.

Tune to the radio station, load the CD, video, DVD etc.

Checking your system settings

Select the input signal according to the signal to be recorded.

Use the status display screen to check your current settings for features such as surround back channel processing and your current MCACC preset.

Use the remote control’s SIGNAL SEL button.

Prepare the recorder.

1	Press
settings.

Insert a blank tape, MD, video etc. into the recording device and set the recording levels. Refer to the instructions
that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level
automatically-check the component’s instruction manual if you’re unsure.

5	

When the Web Control screen appears, select the item you want to set.

!	 You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle
through the sleep options again.
!	 The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.

Use the input function buttons (or INPUT SELECT).

4	

Input the receiver’s IP address into the browser’s address input field.

%	Press
time.

You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to
the receiver (such as a CD player or TV).
Keep in mind you can’t make a digital recording from an analog source or vice-versa, so make sure the components you are recording to/from are hooked up in the same way (see Connecting your equipment on page 18 for
more on connections).
!	 The receiver’s volume, Audio parameters (the tone controls, for example), and surround effects have no effect
on the recorded signal.
!	 Some digital sources are copy-protected, and can only be recorded in analog.
!	 Some video sources are copy-protected. These cannot be recorded.
Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use
the same type of video cable for connecting your recorder as you used to connect your video source (the one you
want to record) to this receiver. For example, you must connect your recorder using Component video if your
source has also been connected using Component video.

3	

2	

The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use the remote control to set the sleep timer.

Making an audio or a video recording

2	

Turn on the computer’s power and launch the Internet browser.

Using the sleep timer

a	 The volume cannot be adjusted on the receiver if Volume Level at ZONE 2 Setup under ZONE Setup is set to –40 dB Fixed or
0 dB Fixed.

1	

1	

to the receiver operation mode, then press STATUS to check the system

The front panel display shows each of the following settings for three seconds each: Input Source d Sampling
Frequency d MCACC preset d ZONE 2 input d ZONE 3 input.

Start recording, then start playback of the source component.

2	

67

When you’re finished, press STATUS again to switch off the display.

　
　
　
　

09

Using other functions

Setting

Resetting the system

Default
iPod/USB, INTERNET RADIO, SiriusXM,
PANDORA, MEDIA SERVER, FAVORITES,
ADAPTER PORT input function

ON

Other input functions

OFF

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.
Set MULTI-ZONE to MULTI ZONE OFF.
!	 Disconnect the iPod and USB memory device from the receiver beforehand.
!	 Set the Control with HDMI to OFF (see HDMI Setup on page 59).

Sound Delay

0.0 frame

1	

Switch the receiver into standby.

Dual Mono

CH1

2	

While holding down ENTER on the front panel, press u STANDBY/ON.

DRC

AUTO

SACD Gain

0 dB

LFE Attenuate

0 dB

The display shows RESET? OK.

Auto delay

OFF

4	

Digital Safety

Auto Sound Retriever

The display shows RESET c NO d.

3	

Select ‘RESET’ using PRESET k/l, then press ENTER on the front panel.
Press ENTER to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default settings.
!	 Note that all settings will be saved, even if the receiver is unplugged.

50

Center Width

3

Dimension

0

Panorama

OFF

Neo:6 Options

Center Image

Neo:6 CINEMA: 10
Neo:6 MUSIC: 3

2 PL IIz Options

Height Gain

MID

Listening Mode (2 ch/multi ch)

AUTO SURROUND

Listening Mode (Headphones)

STEREO

2 PL II Music Options

Setting

Default

Digital Video Converter

ON

SPEAKERS

SB/FH ON

Speaker System

Normal(SB/FH)

Speaker Setting

90

Other modes

Effect Level

Default system settings

Front

SMALL

Center

SMALL

FH/FW

SMALL

Surr

SMALL

SB

SMALLx2

SW

YES

Surround Position

IN REAR

Crossover

80 Hz

X-Curve

OFF

DIMMER

Brightest

All Inputs

See also Setting the Audio options on page 62 for other default DSP settings.
MCACC

OFF

Control Mode

--- (OFF)

ARC (Audio Return Channel)

--- (OFF)

PQLS

--- (AUTO)

Standby Through

OFF

DSP
Power On Level

LAST

Volume Limit

OFF

Mute Level

FULL

Phase Control

ON

0.0 dB

EQ Data (M1 to M6)

HDMI
AMP

M1: MEMORY 1

Standing Wave (M1 to M6)

See Input function default and possible settings on page 39.

Control

MCACC Position Memory
Channel Level (M1 to M6)
Speaker Distance (M1 to M6)

Inputs

HDMI Audio

OFF
ExtendedStereo

68

10’00’’
ATT of all channels/filters

0.0 dB

SWch Wide Trim

0.0 dB

All channels/bands

0.0 dB

EQ Wide Trim

0.0 dB

　
　
　
　

Controlling the rest of your system
About the Remote Setup menu..................................................................................................... 70
Operating multiple receivers......................................................................................................... 70
Setting the remote to control other components....................................................................... 70
Selecting preset codes directly...................................................................................................... 70
Programming signals from other remote controls...................................................................... 71
Erasing one of the remote control button settings..................................................................... 71
Erasing all learnt settings that are in one input function........................................................... 71
Direct function................................................................................................................................ 72
About the ALL ZONE STBY (All Zone Standby) and DISCRETE ON (Discrete On) functions...... 72
Resetting the remote control settings.......................................................................................... 72
Controlling components................................................................................................................ 73

69

　
　
　
　

10

Controlling the rest of your system

About the Remote Setup menu

Setting the remote to control other components

The Remote Setup mode is set by pressing the number button while pressing RCU SETUP. The different items
on the Remote Setup menu are described below. For their setting procedures, refer to the explanations for the
respective items.

Most components can be assigned to one of the input function buttons (such as DVD or CD) using the component’s manufacturer preset code stored in the remote.
However, there are cases where only certain functions may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote control will not work for the model that you are using.
If you can’t find a preset code that matches the component you want to control, you can still teach the remote
individual commands from another remote control (see Programming signals from other remote controls on
page 71).
!	 With the TV CONTROL buttons, the TV can be operated regardless of the input set for the remote control’s
operation mode. When using one TV set, we recommend assigning the same TV’s preset codes to the
TV CONTROL INPUT button and the TV button. When using two TV sets, for better convenience assign the TV
connected to the MONITOR OUT terminals to the TV CONTROL INPUT button, the other TV to the TV button.
!	 Devices may be assigned to the following input function buttons.

Setting

What it does

Preset recall

Preset codes can be set for the various input functions. The remote control codes of a number of other
devices (including products of other brands) are preset in the remote control to allow these devices to be
operated. See Selecting preset codes directly on page 70.

Code learning

If the desired operations cannot be performed even though you have set the preset codes, the remote control
signals of other devices can be learned directly. See Programming signals from other remote controls on
page 71.

Direct function

This is a setting for changing only the remote control unit’s operation screen, without changing the receiver’s
input, when the remote control unit’s input function buttons are pressed. This is convenient for using the
remote control unit for devices not connected to the receiver. See Direct function on page 72.

Erase learning

This function is used to erase remote control codes that have been learned. Codes learned for the different
input functions can be erased individually. See Erasing one of the remote control button settings on page 71.

Reset function

This is a function for resetting preset codes that have been set. Key resetting can be done for individual input
functions. See Erasing all learnt settings that are in one input function on page 71.

All reset

This is a function for resetting all remote control unit settings you have made to the defaults set upon shipment from the factory. See Resetting the remote control settings on page 72.

Change RC
mode

If you have multiple Pioneer receivers, amplifiers, etc., this setting can be used to prevent other units from
operating simultaneously when the remote control unit is operated. See Operating multiple receivers on page
70.

RECEIVER ALL ZONE STBY
DISCRETE ON

SOURCE

RCU SETUP
BDR
BD

DVD

DVR

HDMI

ADPT

TV

CD

NET

USB

CBL

OPTION 1

iPod

SAT

TUNER

INPUT SELECT

STATUS

INPUT

Note

RECEIVER

VOLUME

TV CONTROL

!	 You can cancel or exit any of the steps by pressing RCU SETUP.
!	 After one minute of inactivity, the remote automatically exits the operation.

CH

VOL

MUTE

Operating multiple receivers
Up to four receivers can be operated discretely using this receiver’s remote control when using multiple receivers, provided they are of the same model as this receiver. The receiver to be operated is switched by inputting the
preset code to set the remote control setting.
!	 Set the remote modes on the receivers before using this function (see Remote Control Mode Setup on page
88).

1	

Selecting preset codes directly
1	

Press and hold RCU SETUP, then press ‘1’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.
!	 To cancel the preset setup mode press RCU SETUP.

Press and hold RCU SETUP, then press ‘4’ for three seconds.

2	

Release the button after the LED flashes once. The LED continues to flash.
!	 To cancel the preset setup mode press RCU SETUP.

Press the input function button for the component you want to control.

To assign the preset codes of the TV to be operated with the TV CONTROL function, press the TV CONTROL
INPUT button.
The LED blinks once and flashes continuously.

2	 Press the number button for the receiver (“Receiver 1” to “Receiver 4”) you wish to
operate.

3	

For example, to operate “Receiver 2”, press ‘2’.
If the LED lights for one second and continues to flash, the setting has been successfully completed.
When the preset code is input, the LED flashes three times to indicate that the setting has failed.

Use the number buttons to enter the 4-digit preset code.

See Preset code list on page 109.
If the LED lights for one second and continues to flash, the setting has been successfully completed.
When the preset code is fully input, the LED flashes three times to indicate that the setting has failed. If this happens, enter the 4-digit preset code again.

70

　
　
　
　

10
4	

Controlling the rest of your system

!	 The remote controls should be 3 cm (1 inch) apart.

Repeat steps 2 through 3 for the other components you want to control.

To try out the remote control, switch the component on or off (into standby) by pressing u SOURCE. If it doesn’t
seem to work, select the next code from the list (if there is one).

5	

Press RCU SETUP to exit the preset setup mode.
This receiver’s
remote control

Programming signals from other remote controls

If the LED lights for one second and continues to flash, the setting has been successfully completed.
!	 If the LED flashes for five seconds, it means the memory is full. See Erasing all learnt settings that are in one
input function on page 71 to erase a programmed button you’re not using to free up more memory (note that
some signals may take more memory than others).
!	 Note that interference from TVs or other devices will sometimes result in the remote control learning the
wrong signal.
!	 Some commands from other remote controls cannot be learned, but in most cases the remotes just need to
be moved closer together or farther apart.

SOURCE

RCU SETUP

5	

BDR
BD

DVD

DVR

HDMI

TV

CD

NET

ADPT

USB

CBL

OPTION 1

iPod

SAT

TUNER
STATUS

INPUT

RECEIVER

VOLUME

CH

VOL

PHASE

PQLS

MPX

6	

D.FILT

Erasing one of the remote control button settings

TUNE

This erases one of the buttons you have programmed and restores the button to the factory default.

AUTO/ALC/
DIRECT STANDARD ADV SURR +Favorite

1

2
5

SPEAKERS DIMMER

7

8

1	

3

AUDIO
AUTO
CH LEVEL S.RTRV

6
SLEEP

9

VIDEO
PARAMETER

TOP MENU

0

ENTER

ZONE 2

ZONE 3

ZONE 4

Z2

Z3

Z4

/ CLR

CH

2	

CH

3	

RECEIVER

iPod CTRL

1	

4	

Repeat step 3 to erase other buttons.

5	

Press RCU SETUP to exit the erasing mode.

Erasing all learnt settings that are in one input function

Press and hold RCU SETUP, then press ‘2’ for three seconds.

This operation erases all the operational settings of other devices that have been programmed in one input function, and restores the factory default.
This function is handy for erasing all data programmed for devices no longer being used.

Release the button after the LED flashes once. The LED continues to flash.
!	 To “learn” codes at the TV CONTROL buttons, proceed to step 3.
!	 To cancel the preset setup mode press RCU SETUP.

2	

Press and hold the button to be erased for three seconds.

If the LED lights for one second, the erasing has been successfully completed.

ENTER

RETURN

Press the input function button corresponding to the command to be erased.

The LED flashes once.

OPTION 2

TOOLS
MENU

HOME
MENU

Press and hold RCU SETUP, then press ‘7’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.
!	 To erase operations registered at the TV CONTROL buttons, proceed to step 3.
!	 To cancel the preset setup mode press RCU SETUP.

DISP

D.ACCESS HDMI OUT CLASS
AUDIO
PARAMETER

Press RCU SETUP to exit the programming mode.

PTY

PRESET

4
MUTE

Hi-Bit

BAND

SIGNAL SEL MCACC

TV CONTROL

To program additional signals for the current component repeat steps 3 and 4.

To program signals for another component, exit and repeat steps 2 through 4.
FEATURES

INPUT SELECT

Other remote
control

4	 Press the corresponding button on the other remote control that is sending (teaching) the
signal to this receiver’s remote control.

If the preset code for your component is not available, or the available preset codes do not operate correctly, you
can program signals from the remote control of another component. This can also be used to program additional
operations (buttons not covered in the presets) after assigning a preset code.
The remote can store about 120 preset codes from other components (this has been tested with codes of Pioneer
format only).
Certain buttons represent operations that cannot be learned from other remote controls. The buttons available
are shown below:
RECEIVER ALL ZONE STBY
DISCRETE ON

3 cm
(1 inch)

1	

Press the input function button for the component you want to control.

Press and hold RCU SETUP, then press ‘9’ for three seconds.

The LED blinks once and flashes continuously.

Release the button after the LED flashes once. The LED continues to flash.
!	 To cancel the preset setup mode press RCU SETUP.

3	 Point the two remote controls towards each other, then press the button that will be
doing the learning on this receiver’s remote control.

2	 Press and hold the input function button corresponding to the command to be erased for
three seconds.

The LED flashes once, then stops flashing, remaining lit.

To erase the operations registered at all the TV CONTROL buttons, press the TV CONTROL INPUT button for 3
seconds.
If the LED lights for one second, the erasing has been successfully completed.

71

　
　
　
　

10

Controlling the rest of your system

Direct function

Using Discrete On

!	 Default setting: On
You can use the direct function feature to control one component using the remote control while at the same
time, using your receiver to playback a different component. This could let you, for example, use the remote
control to set up and listen to a CD on the receiver, and then use the remote control to rewind a tape in your VCR
while you continue to listen to your CD player.
When direct function is on, any component you select (using the input function buttons) will be selected by both
the receiver and the remote control. When you turn direct function off, you can operate the remote control without affecting the receiver.

1	

1	

2	

Resetting the remote control settings
Use this procedure to reset all the remote control’s settings to the factory default.
!	 When preset codes are set, all the signals learned in the input function buttons are cleared. This function is
convenient when you want to reset some but not all of input function buttons.

Release the button after the LED flashes once. The LED continues to flash.
!	 To cancel the preset setup mode press RCU SETUP.

Press the input function button for the component you want to control.

3	

Press ‘1’ (On) or ‘0’ (Off) to switch the direct function mode.

1	

Press and hold RCU SETUP, then press ‘0’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

If the LED lights for one second and continues to flash, the setting has been successfully completed.
If the LED flashes three times, the setting has failed.

4	

Press an input function button you want to play.

The receiver’s power turns on (if it was already on, it stays on, without turning off), and the input switches to the
input selected here.

Press and hold RCU SETUP, then press ‘5’ for three seconds.

2	

Press ALL ZONE STBY DISCRETE ON.

The LED continues to flash.

2	

Press and hold the ENTER button for three seconds.

If the LED lights for one second, the erasing has been successfully completed.

Press RCU SETUP to exit the setup.

Default preset codes

About the ALL ZONE STBY (All Zone Standby) and DISCRETE ON
(Discrete On) functions
ALL ZONE STBY (All Zone Standby)
The All Zone Standby can be used to turn all zones to OFF when the receiver’s power is switched to standby.
Also, when using separate Pioneer amplifiers/receivers for the sub zones, they can also be set to standby
simultaneously.
!	 In order to set the power of amplifiers/receivers connected to sub zones to the standby mode, the connected
amplifiers/receivers must be installed or connected in such a way that they can receive remote control signals.
!	 The power of the amplifiers/receivers can be switched to standby with this operation even when using multiple
Pioneer amplifiers/receivers and their Remote Control Mode have been changed.

DISCRETE ON (Discrete On)
The Discrete On function lets you perform a series of operations: switching to the input you want to play while
turning the receiver’s power on.
When the receiver is installed in an AV rack, etc., and you cannot tell whether the power is set to the on or the
standby mode, this operation is handy because it allows you to switch to the selected input without switching the
receiver’s power to standby, even if the power is on when the operation is performed.

Using All Zone Standby
1	

Press ALL ZONE STBY DISCRETE ON.

The LED continues to flash.

2	Press u RECEIVER.
The receiver’s power switches to standby and all zones are turned off.

72

Input function button

Preset code

BD

2255

DVD

2197

DVR/BDR

2144

HDMI

2034

TV

0305

CD

5000

SAT/CBL

6329

OPTION

1103

TV CONTROL (INPUT)

0305

　
　
　
　

10

Controlling the rest of your system

TV and Audio/Video components

Controlling components
This remote control can control components after entering the proper codes (see Setting the remote to control
other components on page 70 for more on this). Use the input function buttons to select the component.
RECEIVER ALL ZONE STBY
DISCRETE ON

SOURCE

RCU SETUP
BDR
BD

DVD

DVR

HDMI

TV

CD

NET

ADPT

USB

CBL

OPTION 1

iPod

SAT

Button(s)

TV

TV (Monitor) BD/DVD

HDD/BDR/
DVR

VCR

SAT/CATV

u SOURCE

POWER ON/
OFF

POWER ON/
OFF

POWER ON/
OFF

POWER ON/
OFF

POWER ON/
OFF

POWER ON/
OFF

Number buttons

numerics

numerics

numerics

numerics

numerics

numerics

!/CLR

! (dot)

KURO LINK

CLEAR

+

—

*

ENTER (CLASS)

CH ENTER

CH ENTER

ENTER

ENTER

—

ENTER

EXIT/INFO

EXIT

TOP MENU

TOP MENU

—

LIST

TOOLS/GUIDE/
EPG

USER MENU

TOOLS


GUIDE

—

GUIDE

i/j/k/l

i/j/k/l

i/j/k/l

i/j/k/l

i/j/k/l

—

i/j/k/l

ENTER

ENTER

ENTER

ENTER

ENTER

—

ENTER

HOME MENU

HOME MENU

HOME MENU

HOME MENU

—

HOME MENU

RETURN

RETURN

RETURN

RETURN

—

RETURN

d

—

—

d

d

d

d

e

—

AUTO SETUP

e

e

e

e

g

—

FREEZE

g

g

g

g

m

—

—

m

m

m

m

n

—

—

n

n

n

n

o

ANT

AV SELECTION

o

o

—

o

p

—

SCREEN SIZE

p

p

—

p

AUDIO

AUDIO

AUDIO

AUDIO

AUDIO

AUDIO

AUDIO

DISP

DISPLAY

DISPLAY

DISPLAY

DISPLAY

—

DISPLAY/INFO

CH +/–

OUTPUT
RESOLUTION
+/–


CH +/–

CH +/–

CH +/–

TUNER

INPUT SELECT

STATUS

RECEIVER

VOLUME

INPUT
TV CONTROL

CH

VOL

MUTE

AUDIO
PARAMETER

VIDEO
PARAMETER

TOOLS
MENU

TOP MENU

ENTER
HOME
MENU

RETURN

iPod CTRL

FEATURES
PHASE

PQLS

MPX

Hi-Bit

BAND

D.FILT
PTY

CH +/–
PRESET

TUNE

AUTO/ALC/
DIRECT STANDARD ADV SURR +Favorite
AUDIO
1
2
3

SIGNAL SEL MCACC

4

5

SPEAKERS DIMMER

7

8

a	 Controls for BD.

AUTO
CH LEVEL S.RTRV

6

DISP

SLEEP

9

CH

D.ACCESS HDMI OUT CLASS
/ CLR

0

ZONE 2

ZONE 3

Z2

Z3

ENTER

CH

ZONE 4 OPTION 2

Z4

RECEIVER

73

CH +/–

　
　
　
　

10

Controlling the rest of your system

Audio/Video components

TV (Projector)

Button(s)

LD

CD/CD-R/SACD

MD/DAT

TAPE

Button(s)

TV (Projector)

u SOURCE

POWER ON/OFF

POWER ON/OFF

POWER ON/OFF

POWER ON/OFF

u SOURCE

POWER ON

Number buttons

numerics

numerics

numerics

—

1

MOVIE

CLEAR

2

STANDARD

3

DYNAMIC

4

USER1

5

USER2

6

USER3

7

COLOR+

8

SHARP+

!/CLR

+10

>10/CLEAR

CLEAR


ENTER (CLASS)

ENTER

DISC/ENTER

OPEN/CLOSE


ENTER

—

MSc

TOP MENU

—

—

LEGATO LINK


—

MSd

i/j/k/l

i/j/k/l

—

—

e/g/m/n

9

GAMMA

ENTER

ENTER

—

—

—

0

COLOR–

—

SACD SETUP


—

—

!/CLR

SHARP–

RETURN

—

—

—

ENTER (CLASS)

COLOR TEMP

d

d

d

d

d

e

e

e

e

e

g

g

g

g

g

i/j/k/l

m

m

m

m

m

ENTER

n

n

n

n

n

o

o

o

o

o

p

p

p

p

p

AUDIO

AUDIO

PURE AUDIO


—

—

DISP

DISPLAY/INFO

TIME


—

—

EXIT
INFO
i/j/k/l
ENTER
TEST
HIDE
MENU

a	 Controls for MD.
b	 Controls for SACD.

74

m

HDMI1

d

HDMI2

n

COMP.

o

VIDEO

e

S-VIDEO

g

BRIGHT–

p

BRIGHT+

AUDIO

POWER OFF

DISP

ASPECT

CH +/–

CONTRAST+/–

　
　
　
　

The Advanced MCACC menu
Making receiver settings from the Advanced MCACC menu..................................................... 76
Automatic MCACC (Expert)........................................................................................................... 76
Manual MCACC setup.................................................................................................................... 78
Checking MCACC Data................................................................................................................... 80
Data Management.......................................................................................................................... 81

75

　
　
　
　

11

The Advanced MCACC menu

!	 Auto MCACC – The default is ALL (recommended), but you can limit the system calibration to only one setting (to save time) if you want.
—	 When data measurement is taken (after selecting ALL or Keep SP System), the reverb characteristics
data (both before- and after-calibration) that this receiver had been storing will be overwritten.
—	 When measurement is performed with other than SYMMETRY (after selecting ALL or Keep SP System),
the reverberation characteristics after calibration cannot be predicted, so the graph for the characteristics
after calibration (“After”) cannot be displayed. If you will need to display the graph for the characteristics
after calibration (“After”), take the measurement using the EQ Professional menu in the Manual MCACC
setup (page 78).
—	The EQ Pro & S-Wave measurement is also taken when ALL or Keep SP System is selected. See
Acoustic Calibration EQ Professional on page 79 for more on this.
—	 Either effect of Acoustic Calibration EQ Professional and Standing Wave can be switched on and off in the
respective MCACC preset. For details, see Setting the Audio options on page 62.
!	 EQ Type (only available when the Auto MCACC Menu above is EQ Pro & S-Wave) – This determines how the
frequency balance is adjusted.
	 After a single calibration is performed, each of the following three correction curves can be stored separately
in the MCACC memory.
—	 SYMMETRY implements symmetric correction for each pair of left and right speakers to flatten the
frequency-amplitude characteristics.
—	 ALL CH ADJ is a ‘flat’ setting where all the speakers are set individually so no special weighting is given to
any one channel.
—	 FRONT ALIGN sets all speakers in accordance with the front speaker settings (no equalization is applied
to the front left and right channels).
	 If you selected ALL or Keep SP System as your Auto MCACC menu, you can specify the MCACC preset
where you want to save the SYMMETRY, ALL CH ADJ and FRONT ALIGN settings.
!	 THX Speaker (only available when the Auto MCACC Menu above is ALL or Speaker Setting) – Select YES
when using THX speakers (all speakers other than the front speakers are set to SMALL). In other cases, leave
at NO.
!	 STAND.WAVE Multi-Point (only available when the Auto MCACC Menu above is EQ Pro & S-Wave) – In
addition to measurements at the listening position, you can use two more reference points for which test
tones will be analyzed for standing waves. This is useful if you want to get a balanced ‘flat’ calibration for several seating positions in your listening area. Place the microphone at the reference point indicated on-screen
and note that the last microphone placement will be at your main listening position:

Making receiver settings from the Advanced MCACC menu
The Advanced MCACC (Multi Channel ACoustic Calibration) system was developed in Pioneer’s laboratories with
the aim of making it possible for home users to perform adjustments of the same level as in a studio easily and
with high precision. The acoustic characteristics of the listening environment are measured and the frequency
response is calibrated accordingly to allow high precision, automatic analysis and optimal calibration of the
sound field to bring it closer to a studio environment than ever before. Furthermore, while it was previously difficult to eliminate standing waves, this receiver is equipped with a standing wave control function using a unique
process to perform acoustic analysis and reduce their influence.
This section describes how to calibrate the sound field automatically and fine-adjust the sound field data
manually.

1	Press u RECEIVER to switch on the receiver and your TV.
Make sure that the TV’s video input is set to this receiver.

2	Press

on the remote control, then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.
!	Press HOME MENU at any time to exit the Home Menu.

3	

Select ‘Advanced MCACC’ from the Home Menu, then press ENTER.

4	

Select the setting you want to adjust.

!	 Full Auto MCACC – See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37 for
a quick and effective automatic surround setup.
!	 Auto MCACC – See Automatic MCACC (Expert) on page 76 for a more detailed MCACC setup.
!	 Manual MCACC – Fine-tunes your speaker settings and customizes the Acoustic Calibration EQ (see Manual
MCACC setup on page 78).
!	 Demo – No settings are saved and no errors occur. When the speakers are connected to this receiver, the
test tone is output repeatedly. Press RETURN to cancel the test tone.

Automatic MCACC (Expert)
If your setup requires more detailed settings than those provided in Automatically conducting optimum sound
tuning (Full Auto MCACC) on page 37, you can customize your setup options below. You can calibrate your system differently for up to six different MCACC presets, which are useful if you have different listening positions
depending on the type of source (for example, watching movies from a sofa, or playing a video game close to the
TV).

2nd reference
point

3rd reference
point

1

2

Important
!	 Make sure the microphone/speakers are not moved during the Auto MCACC Setup.
!	 The screen saver will automatically appear after five minutes of inactivity.

3

Main listening
position

CAUTION

3	

!	 The test tones used in the Auto MCACC Setup are output at high volume.

1	

Select ‘Auto MCACC’ from the Advanced MCACC menu, then press ENTER.

If the Advanced MCACC screen is not displayed, refer to Making receiver settings from the Advanced MCACC
menu on page 76.

2	

Connect the microphone to the MCACC SETUP MIC jack on the front panel.

Make sure there are no obstacles between the speakers and the microphone.

Select the parameters you want to set.

Use i/j to select the item, then use k/l to set.

76

　
　
　
　

11

The Advanced MCACC menu

8	
MULTI-ZONE
CONTROL
ON/OFF

SPEAKERS

iPod iPhone iPad
DIRECT CONTROL

AUTO SURR/ALC/
STREAM DIRECT

STEREO

STANDARD
SURROUND

BAND

PHONES
TUNER EDIT

MCACC
SETUP MIC

5V

USB
2.1 A

HDMI 5 INPUT

9	 The Auto MCACC Setup procedure is completed and the Advanced MCACC menu reappears
automatically.

iPod iPhone iPad

The settings made in the Auto MCACC Setup should give you excellent surround sound from your system, but
it is also possible to adjust these settings manually using the Manual MCACC setup menu (starting below) or
Manual SP Setup menu (starting on page 84).
!	 Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12
cm (5 inches) will end up with different size settings. You can correct the setting manually using the Manual
speaker setup on page 84.
!	 The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and room characteristics into account) and generally does not need to
be changed.
!	 If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing
environment, we recommend adjusting the settings manually.
You can also choose to view the settings by selecting individual parameters from the MCACC Data Check screen
(see Checking MCACC Data on page 80).
Press RETURN after you have finished checking each screen. When you’re finished, select RETURN to go back to
the Home Menu.
Be sure to disconnect the microphone from this receiver upon completion of the Auto MCACC Setup.

Microphone

Tripod

If you have a tripod, use it to place the microphone so that it’s about ear level at your normal listening position. If
you do not have a tripod, use some other object to install the microphone.
!	 It may not be possible to measure correctly if the microphone is placed on a table, sofa, etc.

4	

When you’re finished setting the options, select START then press ENTER.

5	

Follow the instructions on-screen.

6	

Wait for the Auto MCACC Setup to finish outputting test tones.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present
in your setup. Try to be as quiet as possible while it’s doing this.
!	 With error messages (such as Too much ambient noise! or Check microphone.), select RETRY after checking for ambient noise (see Problems when using the Auto MCACC Setup on page 38) and verifying the mic
connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.
!	 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

7	

Make sure ‘OK’ is selected, then press ENTER.

A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum
receiver settings.
Again, try to be as quiet as possible while this is happening. It may take 3 to 7 minutes.
!	 If you selected a STAND.WAVE Multi-Point setup (in step 2), you will be asked to place the mic at the 2nd
and 3rd reference points before finally placing it at your main listening position.

ADVANCED
SURROUND

If necessary, confirm the speaker configuration in the GUI screen.

The configuration shown on-screen should reflect the actual speakers you have.
If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed,
the Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press ENTER in
step 8.
!	 If you see an ERR message (or the speaker configuration displayed isn’t correct), there may be a problem
with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker connections. If there doesn’t seem to be a problem, you can simply use i/j to select the speaker and k/l to
change the setting and continue.
!	 If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the
phase (dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are
properly connected.
	If Reverse Phase is displayed, the speaker’s wiring (+ and –) may be inverted. Check the speaker
connections.
—	 If the connections were wrong, turn off the power, disconnect the power cord, then reconnect properly.
After this, perform the Auto MCACC procedure again.
—	 If the connections were right, select GO NEXT and continue.

77

　
　
　
　

11

The Advanced MCACC menu

3	

Manual MCACC setup
You can use the settings in the Manual MCACC setup menu to make detailed adjustments when you’re more
familiar with the system. Before making these settings, you should have already completed Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37.
You only need to make these settings once (unless you change the placement of your current speaker system or
add new speakers).

4	

Fine Speaker Distance

CAUTION

!	 Default setting: 10’00’’ (all speakers)
For proper sound depth and separation with your system, it is necessary to add a slight bit of delay to some
speakers so that all sounds will arrive at the listening position at the same time. You can adjust the distance of
each speaker in half inch increments. The following setting can help you make detailed adjustments that you may
not achieve using the Manual speaker setup on page 84.

Important
!	 Press the MCACC button while the pertinent setup screens are displayed to select MCACC presets.
!	 For some of the settings below, you’ll have to connect the setup microphone to the front panel and place it
about ear level at your normal listening position. Press HOME MENU to display the Home Menu before you
connect the microphone to this receiver.
!	See Problems when using the Auto MCACC Setup on page 38 for notes regarding high background noise
levels and other possible interference.
!	 If you’re using a subwoofer, switch it on and turn up the volume to the middle position.

Select ‘Manual MCACC’ from the Advanced MCACC menu.
Select the setting you want to adjust.

If you’re doing this for the first time, you might want to make these settings in order.
!	 Fine Channel Level – Make fine adjustments to the overall balance of your speaker system (see Fine Channel
Level on page 78).
!	 Fine SP Distance – Make precise delay settings for your speaker system (see Fine Speaker Distance on page
78).
!	 Standing Wave – Control overly resonant low frequencies in your listening room (see Standing Wave on
page 79).
The last two settings are specifically for customizing the parameters explained in Acoustic Calibration EQ Adjust
on page 79:
!	 EQ Adjust – Manually adjust the frequency balance of your speaker system while listening to test tones (see
Acoustic Calibration EQ Adjust on page 79).
!	 EQ Professional – Calibrate your system based on the direct sound coming from the speakers and make
detailed settings according to your room’s reverb characteristics (see Acoustic Calibration EQ Professional
on page 79).

Adjust the distance of the left channel from the listening position.

3	

Select each channel in turn and adjust the distance as necessary.

4	

!	 Default setting: 0.0dB (all channels)
You can achieve better surround sound by properly adjusting the overall balance of your speaker system. You can
adjust the Channel Level of each speaker in 0.5 dB increments. The following setting can help you make detailed
adjustments that you may not achieve using the Manual speaker setup on page 84.

When you’re finished, press RETURN.

You will return to the Manual MCACC setup menu.

Select ‘Fine Channel Level’ from the Manual MCACC setup menu.

The volume increases to the 0.0 dB reference level.

2	

Select ‘Fine SP Distance’ from the Manual MCACC setup menu.

2	

When it sounds like the delay settings are matched up, press j to confirm and continue to the next channel.
!	 For comparison purposes, the reference speaker will change depending on which speaker you select.
!	 If you want to go back and adjust a channel, simply use i/j to select it.

Fine Channel Level

1	

1	

Use k/l to adjust the delay of the speaker you selected to match the reference speaker.
Listen to the reference speaker and use it to measure the target channel. From the listening position, face the two
speakers with your arms outstretched pointing at each speaker. Try to make the two tones sound as if they are
arriving simultaneously at a position slightly in front of you and between your arm span.
!	 If you can’t seem to achieve this by adjusting the distance setting, you may need to change the angle of your
speakers very slightly.
!	 The subwoofer’s test tone differs in tone from other channels. Adjust so that the sound of the subwoofer can
be heard distinctly. Note that when adjusting the subwoofer, depending on the low frequency response of
your speaker, it may be difficult to hear the change even when the setting is increased or decreased or when
the position of the speaker is changed. Note that it may be difficult to compare this tone with the other speakers in your setup (depending on the low frequency response of the reference speaker).

See Making receiver settings from the Advanced MCACC menu on page 76 if you’re not already at this screen.

2	

When you’re finished, press RETURN.

You will return to the Manual MCACC setup menu.

!	 The test tones used in the Manual MCACC setup are output at high volume.

1	

Select each channel in turn and adjust the levels (+/–12.0 dB) as necessary.

Use k/l to adjust the volume of the speaker you selected to match the reference speaker. When it sounds like
both tones are the same volume, press j to confirm and continue to the next channel.
!	 For comparison purposes, the reference speaker will change depending on which speaker you select.
!	 If you want to go back and adjust a channel, simply use i/j to select it.

Adjust the level of the left channel.

This will be the reference speaker level, so you may want to keep the level around 0.0dB so that you’ll have plenty
of room to adjust the other speaker levels.
!	 After pressing ENTER, test tones will be output.

78

　
　
　
　

11

The Advanced MCACC menu

Standing Wave

Acoustic Calibration EQ Professional

!	 Default setting: ON/ATT 0.0dB (all filters)
Acoustic standing waves occur when, under certain conditions, sound waves from your speaker system resonate
mutually with sound waves reflected off the walls in your listening area. This can have a negative effect on the
overall sound, especially at certain lower frequencies. Depending on speaker placement, your listening position, and ultimately the shape of your room, it results in an overly resonant (‘boomy’) sound. The Standing Wave
Control uses filters to reduce the effect of overly resonant sounds in your listening area. During playback of a
source, you can customize the filters used for Standing Wave Control for each of your MCACC presets.
!	 Standing Wave control filter settings cannot be changed during playback of sources using the HDMI
connection.

This setup minimizes the unwanted effects of room reverberation by allowing you to calibrate your system based
on the direct sound coming from the speakers.
Performing the Acoustic Calibration EQ Professional procedure is effective when the lower frequencies seem
overly reverberant in your listening room (i.e. it sounds ‘boomy’) as shown at Type A below, or when different
channels seem to exhibit different reverb characteristics as shown at Type B.
!	 Type A: Reverberance of high vs. low frequencies

1	

Select ‘Standing Wave’ from the Manual MCACC setup menu.

2	

Adjust the parameters for the Standing Wave Control.

High frequencies
Acoustic Cal. EQ Pro.
calibration range

!	 Filter Channel – Select the channel to which you will apply the filter(s): MAIN (all except center channel and
subwoofer), Center or SW (subwoofer).
!	 TRIM (only available when the filter channel above is SW) – Adjust the subwoofer channel level (to compensate for the difference in output post-filter).
!	 Freq / Q / ATT – These are the filter parameters where Freq represents the frequency you will be targeting
and Q is the bandwidth (the higher the Q, the narrower the bandwidth, or range) of the attenuation (ATT, the
amount of reduction to the targeted frequency).

3	

Low frequencies

Level

0

80

!	 Type B: Reverb characteristics for different channels
Front L

Level

When you’re finished, press RETURN.

Front R

You will return to the Manual MCACC setup menu.
Acoustic Cal. EQ Pro.
calibration range

Acoustic Calibration EQ Adjust
!	 Default setting: ON/0.0dB (all channels/bands)
Acoustic Calibration Equalization is a kind of room equalizer for your speakers (excluding the subwoofer). It works
by measuring the acoustic characteristics of your room and neutralizing the ambient characteristics that can
color the original source material (providing a ‘flat’ equalization setting). If you’re not satisfied with the adjustment provided in Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37 or Automatic
MCACC (Expert) on page 76, you can also adjust these settings manually to get a frequency balance that suits
your tastes.

1	

Select ‘EQ Adjust’ from the Manual MCACC setup menu.

2	

Select the channel(s) you want and adjust to your liking.

0

80

Conventional MCACC
EQ calibration range
Time
(in msec)
160

Using Acoustic Calibration EQ Professional
1	

Select ‘EQ Professional’, then press ENTER.

2	

Select an option and press ENTER.

!	 Reverb Measurement – Use this to measure the reverb characteristics before and after calibration.
!	 Reverb View – You can check the reverb measurements made for specified frequency ranges in each
channel.
—	 If the Reverb View procedure is performed after the Automatically conducting optimum sound tuning
(Full Auto MCACC) on page 37 or Reverb Measurement operation, depending on the standing wave
control setting, differences may appear on the reverb graph. With the Auto MCACC function, the reverberations are measured with the standing waves controlled, so the reverb characteristics graph shows the
characteristics with the effect of the standing waves eliminated. By contrast, the Reverb Measurement
function measures the reverberations without controlling the standing waves, so the graph indicates the reverb characteristics including the effect of the standing waves. If you wish to check the
reverb characteristics of the room itself (with the standing waves as such), we recommend using the
Reverb Measurement function.
!	 Advanced EQ Setup – Use this to select the time period that will be used for frequency adjustment and
calibration, based on the reverb measurement of your listening area. Note that customizing system calibration using this setup will alter the settings you made in Automatically conducting optimum sound tuning (Full
Auto MCACC) on page 37 or Automatic MCACC (Expert) on page 76 and is not necessary if you’re satisfied
with these settings.

Use i/j to select the channel.
Use k/l to select the frequency and i/j to boost or cut the EQ. When you’re finished, go back to the top of
the screen and press k to return to Ch, then use i/j to select the channel.
!	The OVER! indicator shows in the display if the frequency adjustment is too drastic and might distort. If this
happens, bring the level down until OVER! disappears from the display.

3	

Conventional MCACC
EQ calibration range
Time
160
(in msec)

When you’re finished, press RETURN.

You will return to the Manual MCACC setup menu.

Note
!	 Changing the frequency curve of one channel too drastically will affect the overall balance. If the speaker balance seems uneven, you can raise or lower channel levels using test tones with the TRIM feature. Use k/l to
select TRIM, then use i/j to raise or lower the channel level for the current speaker.

79

　
　
　
　

11
3	

The Advanced MCACC menu

If you selected ‘Reverb Measurement’, select EQ ON or EQ OFF, and then START.

Checking MCACC Data

The following options determine how the reverb characteristics of your listening area are displayed in
Reverb View:
!	 EQ OFF – You will see the reverb characteristics of your listening area without the equalization performed by
this receiver (before calibration).
!	 EQ ON – You will see the reverb characteristics of your listening area with the equalization performed by this
receiver (after calibration). Note that the EQ response may not appear entirely flat due to adjustments necessary for your listening area.
—	 The calibration corresponding to the currently selected MCACC preset will be used when EQ ON is
selected. To use another MCACC preset, press MCACC to select the MCACC memory you want to store.
—	 After auto calibration with EQ Type : SYMMETRY (Full Auto MCACC, etc.), the graph for the inferred
reverb characteristics can be displayed by selecting Reverb View. To display the actually measured
reverb characteristics after EQ calibration, measure with EQ ON.
When the reverb measurement is finished, you can select Reverb View to see the results on-screen. See
Professional Calibration EQ graphical output on page 94 for troubleshooting information.

At the procedure of Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37, the procedure of Automatic MCACC (Expert) on page 76 or after fine-adjusting at Manual MCACC setup on page 78, you
can check your calibrated settings using the GUI screen.

1	Press

on the remote control, then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.

2	

Select ‘MCACC Data Check’ from the Home Menu.

3	

Select the setting you want to check.

!	 Speaker Setting – Used to check the settings of the speaker systems. See Speaker Setting on page 80 for
more on this.
!	 Channel Level – Used to check the output level of the different speakers. See Channel Level on page 80 for
more on this.
!	 Speaker Distance – Used to check the distance to the different speakers. See Speaker Distance on page 80
for more on this.
!	 Standing Wave – Used to check the standing wave control filter settings. See Standing Wave on page 81 for
more on this.
!	 Acoustic Cal EQ – Used to check the calibration values of the listening environment’s frequency response.
See Acoustic Cal EQ on page 81 for more on this.

4	 If you selected ‘Reverb View’, you can check the reverb characteristics for each channel.
Press RETURN when you’re done.
The reverb characteristics are displayed when the Full Auto MCACC or Reverb Measurement measurements
are conducted.
Use k/l to select the channel, frequency and calibration setting you want to check. Use i/j to go back and
forth between the three. The reverb characteristics graph before and after EQ calibration can be displayed by
selecting Calibration : Before / After. Note that the markers on the vertical axis indicate decibels in 2 dB steps.

4	 Press RETURN to go back to the MCACC Data Check menu, repeating steps 2 and 3 to check
other settings.

5	 If ‘Advanced EQ Setup’ is selected, select the MCACC memory to be stored, then enter the
desired time setting for calibration, and then select START.

5	

!	 To specify the place where the MCACC memory is to be stored, press MCACC to select the MCACC memory
you want to store.
Based on the reverb measurement above, you can choose the time period that will be used for the final frequency
adjustment and calibration. Even though you can make this setting without reverb measurement, it is best to use
the measurement results as a reference for your time setting. For an optimal system calibration based on the
direct sound coming from the speakers, we recommend using the 30-50ms setting.
Use k/l to select the setting. Use i/j to switch between them.
Select the setting from the following time periods (in milliseconds): 0-20ms, 10-30ms, 20-40ms, 30-50ms,
40-60ms, 50-70ms and 60-80ms. This setting will be applied to all channels during calibration.
When you’re finished, select START. It will take about 2 to 4 minutes for the calibration to finish.
After the Acoustic Calibration Equalization is set, you are given the option to check the settings on-screen.

When you’re finished, press RETURN.

You will return to the Home Menu.

Speaker Setting
Use this to display the speaker size and number of speakers. See Speaker Setting on page 84 for more on this.

1	

Select ‘Speaker Setting’ from the MCACC Data Check menu.

2	

Select the channel you want to check.

Use i/j to select the channel. The corresponding channel on the layout diagram is highlighted.

Channel Level
Use this to display the level of the various channels. See Channel Level on page 85 for more on this.

1	

Select ‘Channel Level’ from the MCACC Data Check menu.

2	

When ‘MCACC’ is highlighted, use k/l to select the MCACC preset you want to check.

The level of the various channels set at the selected MCACC preset is displayed. ‘---’ is displayed for channels that
are not connected.

Speaker Distance
Use this to display the distance from the different channels to the listening position. See Speaker Distance on
page 85 for more on this.

1	

Select ‘Speaker Distance’ from the MCACC Data Check menu.

2	

When ‘MCACC’ is highlighted, use k/l to select the MCACC preset you want to check.

The distance from the various channels set at the selected MCACC preset is displayed. ‘---’ is displayed for channels that are not connected.

80

　
　
　
　

11

The Advanced MCACC menu

Standing Wave

Data Management

Use this to display the standing wave related adjustment values for the various MCACC memories. See Standing
Wave on page 79 for more on this.

1	

This system allows you to store up to six MCACC presets, allowing you to calibrate your system for different listening positions (or frequency adjustments for the same listening position). This is useful for alternate settings to
match the kind of source you’re listening to and where you’re sitting (for example, watching movies from a sofa,
or playing a video game close to the TV).
From this menu you can copy from one preset to another, name presets for easier identification and clear any
ones you don’t need.
!	 This can be done in Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37 or
Automatic MCACC (Expert) on page 76, either of which you should have already completed.

Select ‘Standing Wave’ from the MCACC Data Check menu.

2	 When ‘Filter Channel’ is highlighted, use i/j to select the channel for which you want to
check standing wave control.
The standing wave related calibration value for the selected channel stored at the selected MCACC preset and its
graph are displayed.

3	Press k to highlight ‘MCACC’, then use i/j to select the MCACC preset you want to
check.

1	Press

Acoustic Cal EQ
Use this to display the calibration values for the frequency response of the various channels set in the different
MCACC presets. See Acoustic Calibration EQ Adjust on page 79 for more on this.

1	

Select ‘Acoustic Cal EQ’ from the MCACC Data Check menu.

2	

When ‘Ch’ is highlighted, use i/j to select the channel.

on the remote control, then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.

2	

Select ‘Data Management’ from the Home Menu.

3	

Select the setting you want to adjust.

!	 Memory Rename – Name your MCACC presets for easy identification (see Renaming MCACC presets on
page 81).
!	 MCACC Memory Copy – Copy settings from one MCACC preset to another (see Copying MCACC preset data
on page 81).
!	 MCACC Memory Clear – Clear any MCACC presets that you don’t want (see Clearing MCACC presets on
page 82).

The calibration value for the frequency response of the selected channel stored at the selected MCACC preset
and its graph are displayed.

3	Press k to highlight ‘MCACC’, then use i/j to select the MCACC preset you want to
check.

Renaming MCACC presets
If you have several different MCACC presets that you’re using, you may want to rename them for easier
identification.

1	

Select ‘Memory Rename’ from the Data Management setup menu.

2	

Select the MCACC preset you want to rename, then select an appropriate preset name.

Use i/j to select the preset, then k/l to select a preset name.

3	

Repeat for as many MCACC presets as necessary, then press RETURN when you’re finished.

You will return to the Data Management setup menu.

Copying MCACC preset data
If you want to manually adjust the Acoustic Calibration EQ (see Manual MCACC setup on page 78), we recommend copying your current settings to an unused MCACC preset. Instead of just a flat EQ curve, this will give you
a reference point from which to start.
!	 The settings made in Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37 or
Automatic MCACC (Expert) on page 76.

1	

Select ‘MCACC Memory Copy’ from the Data Management setup menu.

2	

Select the setting you want to copy.

!	 All Data – Copies all the settings of the selected MCACC preset memory.
!	 Level & Distance – Copies only the channel level and speaker distance settings of the selected MCACC preset memory.

3	 Select the MCACC preset you’ll be copying the settings ‘From’, then specify where you
want to copy them (‘To’).
Make sure you don’t overwrite an MCACC preset you’re currently using (this can’t be undone).

81

　
　
　
　

11
4	

The Advanced MCACC menu

　
　
　
　

Select ‘OK’ to confirm and copy the settings.

When MCACC Memory Copy? is displayed, select YES. If NO is selected, the memory is not copied.
Completed! shows in the GUI screen to confirm the MCACC preset has been copied, then you automatically
return to the Data Management setup menu.

Clearing MCACC presets
If you are no longer using one of the MCACC presets stored in memory, you can choose to clear the calibration
settings of that preset.

1	

Select ‘MCACC Memory Clear’ from the Data Management setup menu.

2	

Select the MCACC preset you want to clear.

Make sure you don’t clear an MCACC preset you’re currently using (this can’t be undone).

3	

Select ‘OK’ to confirm and clear the preset.

When MCACC Memory Clear? is displayed, select YES. If NO is selected, the memory is not cleared.
Completed! shows in the GUI screen to confirm the MCACC preset has been cleared, then you automatically
return to the Data Management setup menu.

82

The System Setup and Other Setup menus
Making receiver settings from the System Setup menu............................................................. 84
Manual speaker setup.................................................................................................................... 84
Network Setup menu..................................................................................................................... 86
Checking the Network Information.............................................................................................. 87
The Other Setup menu................................................................................................................... 87

83

　
　
　
　

12

The System Setup and Other Setup menus

Speaker system setting

Making receiver settings from the System Setup menu

!	 Default setting: Normal(SB/FH)
There are several ways you can use the speaker terminals with this receiver. In addition to a normal home theater
setup where they are used for the front height speakers or front wide speakers, they can be used for bi-amping
the front speakers or as an independent speaker system in another room.

The following section describes how to change the speaker-related settings manually and make various other
settings (input selection, OSD language selection, etc.).

1	Press u RECEIVER to switch on the receiver and your TV.
Make sure that the TV’s video input is set to this receiver.

2	Press

1	

on the remote control, then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.
!	Press HOME MENU at any time to exit the Home Menu.

3	

Select ‘System Setup’ from the Home Menu, then press ENTER.

4	

Select the setting you want to adjust.

Select ‘Speaker System’ from the Manual SP Setup menu.

See Making receiver settings from the System Setup menu on page 84 if you’re not already at this screen.

2	

Select the speaker system setting.

!	 Normal(SB/FH) – Select for normal home theater use with front height speakers in your main (speaker system A) setup.
!	 Normal(SB/FW) – Select for normal home theater use with front wide speakers in your main (speaker system
A) setup.
!	 Speaker B – Select to use the B speaker terminals to listen to stereo playback in another room (see Switching
the speaker terminals on page 66).
!	 Front Bi-Amp – Select this setting if you’re bi-amping your front speakers (see Bi-amping your speakers on
page 22).
!	 ZONE 2 – Select to use the surround back speaker terminals for an independent system in another zone (see
Using the MULTI-ZONE controls on page 66).

!	 Manual SP Setup – Sets the type of connection used for surround back terminals and the size, number distance and overall balance of the connected speakers (see Manual speaker setup on page 84).
!	 Input Setup – Specifies what you’ve connected to the digital, HDMI and component video inputs (see The
Input Setup menu on page 39).
!	 OSD Language – The GUI screen’s display language can be changed (see Changing the OSD display language (OSD Language) on page 37).
!	 Network Setup – Conducts the setup necessary to connect this unit to the network (see Network Setup
menu on page 86).
!	 HDMI Setup – Synchronizes this receiver with your Pioneer component supporting Control with HDMI (page
58).
!	 Other Setup – Makes customized settings to reflect how you are using the receiver (see The Other Setup
menu on page 87).

3	 If you selected Normal(SB/FH), Normal(SB/FW), or Speaker B in Step 2, select the placement
of the surround speakers.
In a 7.1-channel surround system with surround speakers placed directly at the sides of the listening position,
the surround sound of 5.1-channel sources is heard from the side. This function mixes the sound of the surround
speakers with the surround back speakers so that the surround sound is heard from diagonally to the rear as it
should be.
Depending on the positions of the speakers and the sound source, in some cases it may not be possible to
achieve good results. In this case, set the setting to ON SIDE or IN REAR.
!	 ON SIDE – Select when the surround speakers is positioned right beside you.
!	 IN REAR – Select when the surround speaker is positioned obliquely behind you.

Manual speaker setup
This receiver allows you to make detailed settings to optimize the surround sound performance. You only need
to make these settings once (unless you change the placement of your current speaker system or add new
speakers).
These settings are designed to customize your system, but if you’re satisfied with the settings made in
Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37, it isn’t necessary to make all of
these settings.

4	

When ‘Setting Change?’ is displayed, select Yes.

If No is selected, the setting is not changed.
You will return to the Manual SP Setup menu.

Speaker Setting

See Making receiver settings from the System Setup menu on page 84 if you’re not already at this screen.

Use this setting to specify your speaker configuration (size, number of speakers and crossover frequency). It
is a good idea to make sure that the settings made in Automatically conducting optimum sound tuning (Full
Auto MCACC) on page 37 are correct. Note that this setting applies to all MCACC presets, and cannot be set
independently.
!	 If you’re using a THX speaker setup, set all speakers to SMALL.

2	

1	

Select ‘Speaker Setting’ from the Manual SP Setup menu.

2	

Choose the set of speakers that you want to set, then select a speaker size.

CAUTION
!	 The test tones used in the Manual SP Setup are output at high volume.

1	

Select ‘Manual SP Setup’, then press ENTER.
Select the setting you want to adjust.

If you are doing this for the first time, you may want to adjust these settings in order:
!	 Speaker System – Specifies how you are using your surround back speaker terminals and B speaker terminals (page 84).
!	 Speaker Setting – Specifies the size and number of speakers you’ve connected (page 84).
!	 Channel Level – Adjusts the overall balance of your speaker system (page 85).
!	 Speaker Distance – Specifies the distance of your speakers from the listening position (page 85).
!	 X-Curve – Adjusts the tonal balance of your speaker system for movie soundtracks (page 85).

Use k/l to select the size (and number) of each of the following speakers:
!	 Front – Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn’t connect a
subwoofer. Select SMALL to send the bass frequencies to the subwoofer.
!	 Center – Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. If you didn’t connect a center speaker, choose NO
(the center channel is sent to the front speakers).

3	 Make the adjustments necessary for each setting, pressing RETURN to confirm after each
screen.
84

　
　
　
　

12

The System Setup and Other Setup menus

!	 FH – Select LARGE if your front height speakers reproduce bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. If you didn’t connect front height speakers, choose
NO (the front height channel is sent to the front speakers).
—	 You can adjust this setting only when Speaker System setting is Normal(SB/FH).
—	 If the surround speakers are set to NO, this setting will automatically be set to NO.
!	 FW – Select LARGE if your front wide speakers reproduce bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. If you didn’t connect front wide speakers, choose
NO (the front wide channel is sent to the front speakers).
—	 You can adjust this setting only when Speaker System setting is Normal(SB/FW).
—	 If the surround speakers are set to NO, this setting will automatically be set to NO.
!	 Surr – Select LARGE if your surround speakers reproduce bass frequencies effectively. Select SMALL to send
bass frequencies to the other speakers or subwoofer. If you didn’t connect surround speakers choose NO (the
sound of the surround channels is sent to the front speakers or a subwoofer).
!	 SB – Select the number of surround back speakers you have (one, two or none). Select LARGEx2 or LARGEx1
if your surround back speakers reproduce bass frequencies effectively. Select SMALLx2 or SMALLx1 to send
bass frequencies to the other speakers or subwoofer. If you didn’t connect surround back speakers choose
NO.
—	 If you selected ZONE 2 or Front Bi-Amp (in Speaker system setting on page 84) you can’t adjust the surround back settings.
—	 If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.
!	 SW – LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES
is selected. Choose the PLUS setting if you want the subwoofer to output bass sound continuously or you
want deeper bass (the bass frequencies that would normally come out the front and center speakers are also
routed to the subwoofer). If you did not connect a subwoofer choose NO (the bass frequencies are output
from other speakers).
—	 If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers
and PLUS for the subwoofer. This may not, however, yield the best bass results. Depending on the speaker
placement of your room you may actually experience a decrease in the amount of bass due low frequency
cancellations. In this case, try changing the position or direction of speakers. If you can’t get good results,
listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL
alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option is to
route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.
If you select NO for the subwoofer the front speakers will automatically be fixed to LARGE. Also, the center, surround, surround back, front height and front wide speakers can’t be set to LARGE if the front speakers are set to
SMALL. In this case, all bass frequencies are sent to the subwoofer.

3	

Channel Level
Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor
when setting up a home theater system.

1	
2	

Adjust the level of each channel using k/l.

Use i/j to switch speakers.
Adjust the level of each speaker as the test tone is emitted.
!	 If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and
adjust the level of each speaker to 75 dB SPL (C-weighting/slow reading).

3	

When you’re finished, press RETURN.

You will return to the Manual SP Setup menu.

Note
!	 You can change the channel levels by press
then using k/l on the remote control.

to the receiver operation mode, then press CH LEVEL, and

Speaker Distance
For good sound depth and separation from your system, you need to specify the distance of your speakers from
the listening position. The receiver can then add the proper delay needed for effective surround sound.

1	

Select ‘Speaker Distance’ from the Manual SP Setup menu.

2	

Adjust the distance of each speaker using k/l.

You can adjust the distance of each speaker in 1/2 inch Increments.

3	

When you’re finished, press RETURN.

You will return to the Manual SP Setup menu.

Note
!	 For best surround sound, make sure the surround back speakers are the same distance from the listening
position.

X-Curve

Select ‘X. OVER’ and set the crossover frequency.

Frequencies below this point will be sent to the subwoofer (or LARGE speakers).
!	 This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or
the subwoofer, and bass sounds playing back from those selected as SMALL. It also decides where the cutoff
will be for bass sounds in the LFE channel.
!	With Full Auto MCACC setup or Auto MCACC setup (ALL or Speaker Setting), the setting here will not
apply and the crossover frequency will be automatically set. Crossover frequency is a frequency aimed at
achieving the optimal sound field taking into account the bass capacity of all connected speakers and human
aural characteristics.
!	 If you’re using THX speakers, confirm that the crossover frequency is set to 80Hz.

4	

Select ‘Channel Level’ from the Manual SP Setup menu.

The test tones will start.

Most soundtracks mixed for cinema sound too bright when played back in large rooms. The X-Curve setting acts
as a kind of re-equalization for home theater listening, and restores proper tonal balance of movie soundtracks.

1	

Select ‘X-Curve’ from the Manual SP Setup menu.

2	

Choose the X-Curve setting you want.

Use k/l to adjust the setting. The X-Curve is expressed as a downwards slope in decibels per octave, starting
at 2 kHz. The sound becomes less bright as the slope increases (to a maximum of –3.0dB/oct). Use the following
guidelines to set the X-Curve according to your room size:

Room size (ft 2) ≤400 ≤550 ≤650 ≤800 ≤2200 ≤12000

When you’re finished, press RETURN.

X-Curve
(dB/oct)

You will return to the Manual SP Setup menu.

–0.5

–1.0

–1.5

–2.0

–2.5

–3.0

!	 If you select OFF, the frequency curve will be flat and the X-Curve has no effect.

3	
85

When you’re finished, press RETURN.

　
　
　
　

12

The System Setup and Other Setup menus

Proxy Hostname/Proxy Port

Network Setup menu

This setting is required when you connect this receiver to the Internet via a proxy server. Enter the IP address
of your proxy server in the ‘Proxy Hostname’ field. Also, enter the port number of your proxy server in the
‘Proxy Port’ field.

Make the settings for connecting the receiver to the Internet and using the network functions.

1	Press

on the remote control, then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.

1	

Select ‘IP Address, Proxy’ from the Network Setup menu.

2	

Select ‘System Setup’ from the Home Menu.

2	

Select the DHCP setting you want.

3	

Select ‘Network Setup’ from the System Setup menu.

4	

Select the setting you want to adjust.

When you select ON, the network is automatically set up, and you do not need to follow Steps 3. Proceed with
Step 4.
If there is no DHCP server on the network and you select ON, this receiver will use its own Auto IP function to
determine the IP address.
!	 The IP address determined by the Auto IP function is 169.254.X.X. You cannot listen to an Internet radio station if the IP address is set for the Auto IP function.

If you are doing this for the first time, you may want to adjust these settings in order:
!	 IP Address, Proxy – Sets up the IP address/Proxy of this receiver (page 86).
!	 Network Standby – Allows the AVNavigator function to be used even when the receiver is in the standby
mode (page 86).
!	 Friendly Name – The name of the receiver displayed on a computer or other device connected to the network
can be changed (page 86).
!	 Parental Lock – Restricts usage of network functions (page 87).
!	 Port Number Setting – Sets the numbers of the ports where signals from IP Control are received (page 87).

3	 Enter the IP Address, Subnet Mask, Default Gateway, Primary DNS Server and
Secondary DNS Server.
Press i/j to select a number and k/l to move the cursor.

4	 Select ‘OFF’ or ‘ON’ for the Enable Proxy Server setting to deactivate or activate the proxy
server.
In case you select ‘OFF’, proceed with Step 7. In case you select ‘ON’, on the other hand, proceed with Step 5.

IP address/Proxy setting

5	

In case the router connected to the LAN terminal on this receiver is a broadband router (with a built-in DHCP
server function), simply turn on the DHCP server function, and you will not need to set up the network manually.
You must set up the network as described below only when you have connected this receiver to a broadband
router without a DHCP server function. Before you set up the network, consult with your ISP or the network manager for the required settings. It is advised that you also refer to the operation manual supplied with your network
component.
!	 In case you make changes to the network configuration without the DHCP server function, make the corresponding changes to the network settings of this receiver.

Enter the address of your proxy server or the domain name.

Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.

6	

Enter the port number of your proxy server.

Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.

7	

Select ‘OK’ to confirm the IP Address/Proxy setup.

Network Standby
This setting allows the AVNavigator function for operating the receiver from a computer connected on the same
LAN as the receiver to be used even when the receiver is in the standby mode.

IP Address
The IP address to be entered must be defined within the following ranges. If the IP address defined is beyond the
following ranges, you cannot play back audio files stored on components on the network or listen to Internet radio
stations.
Class A: 10.0.0.1 to 10.255.255.254
Class B: 172.16.0.1 to 172.31.255.254
Class C: 192.168.0.1 to 192.168.255.254

1	

Select ‘Network Standby’ from the Network Setup menu.

2	

Specify whether the Network Standby is ON or OFF.

!	 ON – The AVNavigator function can be used even when the receiver is in the standby mode.
!	 OFF – The AVNavigator function cannot be used when the receiver is in the standby mode (This lets you
reduce power consumption in the standby mode).

Friendly Name

Subnet Mask
In case an xDSL modem or a terminal adapter is directly connected to this receiver, enter the subnet mask provided by your ISP on paper. In most cases, enter 255.255.255.0.

1	

Select ‘Friendly Name’ from the Network Setup menu.

2	

Select ‘Edit Name’ then select ‘Rename’.

If after changing the name you want to restore the name to the default, select Default.

Default Gateway

3	

In case a gateway (router) is connected to this receiver, enter the corresponding IP address.

Input the name you want.

Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.

Primary DNS Server/Secondary DNS Server
In case there is only one DNS server address provided by your ISP on paper, enter it in the ‘Primary DNS Server’
field. In case there are more than two DNS server addresses, enter ‘Secondary DNS Server’ in the other DNS
server address field.

86

　
　
　
　

12

The System Setup and Other Setup menus

Parental Lock

The Other Setup menu

Set restrictions for using Internet services. Also set the password accompanying the usage restrictions.
!	 Upon shipment from the factory, the password is set to “0000”.

The Other Setup menu is where you can make customized settings to reflect how you are using the receiver.

1	Press

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.

Important
When the INTERNET RADIO, SiriusXM, PANDORA or FAVORITES input is selected, the setting made here cannot be reflected.

1	

Select ‘Parental Lock’ from the Network Setup menu.

2	

Input the password.
Specify whether to turn Parental Lock on or off.

!	 OFF – Internet services are not restricted.
!	 ON – Internet services are restricted.

4	

If you want to change the password, select Change Password.

In this case, the procedure returns to step 2.

On this receiver, there can be up to 5 numbers of ports where signals are received. One of these, port 8102 cannot
be changed, but the desired number can be set for the 4 other ports.

Select ‘Port Number Setting’ from the Network Setup menu.

2	

Select the port number you want to change.

3	

Input the port number.

Note

Select the setting you want to adjust.

1	

Select ‘Auto Power Down’ from the Other Setup menu.

2	

Select the zone you want to set and set the time after which the power turns off.

!	 MAIN – The time can be selected from among “15 min”, “30 min”, “60 min” and “OFF”. The power turns off
after there has been no signal and no operation for the selected time.
!	 ZONE 2 – The time can be selected from among “30 min”, “1 hour”, “3 hours”, “6 hours”, “9 hours” and
“OFF”. The power turns off after the selected time.
!	 ZONE 3 – The time can be selected from among “30 min”, “1 hour”, “3 hours”, “6 hours”, “9 hours” and
“OFF”. The power turns off after the selected time.

!	 When the wireless LAN converter (AS-WL300) is connected, the port number cannot be set to port 3.
!	 We recommend setting the port number to 23 or within the range of 49152 to 65535.
!	 When the port number is changed, network communications between the receiver and AVNavigator are no
longer possible. In this case, click Settings on the AVNavigator’s function menu, select the IP Address tab and
input one of the port numbers set on the receiver side to enable communications with AVNavigator.

Note

Checking the Network Information

!	 Depending on the connected devices, the Auto Power Down function may not work properly due to excessive
noise or other reasons.

The setting status of the following network-related items can be checked.
!	 IP Address – Check the IP address of this receiver.
!	 MAC Address – Check the MAC address of this receiver.
!	 Friendly Name – Friendly Name on page 86.

on the remote control, then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the
screens and select menu items. Press RETURN to exit the current menu.

2	

Select ‘Other Setup’, then press ENTER.

4	

The power can be set to turn off automatically if no operation has been performed for a specific amount of time
with no audio or video signals being input to the receiver. When using ZONE 2 or ZONE 3, the ZONE 2 or ZONE 3
power can also be set to turn off, but for ZONE 2 or ZONE 3 the power turns off automatically after the amount of
time set here even if signals are being input or operations have been performed.
Different times can be set for the main zone, ZONE 2 and ZONE 3.

If there are other port numbers you want to change, repeat steps 2 and 3.

1	Press

3	

Auto Power Down

!	Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.
!	 It is not possible to set the same port number more than once.

4	

Select ‘System Setup’ from the Home Menu.

5	 Make the adjustments necessary for each setting, pressing RETURN to confirm after each
screen.

Port Number Setting

1	

2	

If you are doing this for the first time, you may want to adjust these settings in order:
!	 Auto Power Down – Sets the power to turn off automatically when the receiver is not being used.
!	 Volume Setup – Sets up the volume-related operations of this receiver (page 88).
!	 Remote Control Mode Setup – Sets this receiver’s remote control mode (page 88).
!	 Software Update – Use to update the receiver’s software and check the version.
!	 ZONE Setup – Use to make the sub zone-related settings (page 89).
!	 EXTENSION Setup – Allows the CU-RF100 to be used even when the receiver is in the standby mode (page
89).

Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.

3	

on the remote control, then press HOME MENU.

Select ‘Network Information’ from the Home Menu.

Display the setting status of the network-related items.

87

　
　
　
　

12

The System Setup and Other Setup menus

!	 If an update file is provided on the Pioneer website, download it onto your computer. When downloading an
update file from the Pioneer website onto your computer, the file will be in ZIP format. Unzip the ZIP file before
saving it on the USB memory device. If there are any old downloaded files or downloaded files for other models
on the USB memory device, delete them.

Volume Setup
You can set the maximum volume of this receiver or specify what the volume level will be when the power is
turned on.

1	

Select ‘Volume Setup’ from the Other Setup menu.

2	

Select the Power ON Level setting you want.

Important

The volume can be set so that it is always set to the same level when the receiver’s power is turned on.
!	 LAST (default) – When the power is turned on, the volume is set to the same level as when the power was last
turned off.
!	“---” – When the power is turned on, the volume is set to minimum level.
!	 –80.0dB to +12.0dB – Specify the volume to be set when the power is turned on, in steps of 0.5 dB.
It is not possible to set a volume level greater than the value specified at Volume Limit setup (see below).

!	 DO NOT unplug the power cord during updating.
!	 When updating via the Internet, do not disconnect the LAN cable. When updating via a USB memory device,
do not disconnect the USB memory device.
!	 If updating is interrupted before it is completed, start updating over from the beginning.
!	 The receiver’s settings may be reset when the software is updated. Information on the models for which the
settings are reset is provided on the Pioneer website. Check the website before updating.

3	

1	

Select ‘Software Update’ from the Other Setup menu.

2	

Select the update procedure.

Select the Volume Limit setting you want.

Use this function to limit the maximum volume. The volume cannot be increased above the level set here, even by
operating VOLUME button (or the dial on the front panel).
!	 OFF (default) – The maximum volume is not limited.
!	 –20.0dB/–10.0dB/0.0dB – The maximum volume is limited to the value set here.

4	

!	 Update via Internet – The receiver checks whether updatable software is available via the Internet.
!	 Update via USB Memory – The receiver checks whether the USB memory device inserted into the USB port
on the receiver’s front panel contains updatable software.
	“Accessing” is displayed and the update file is checked. Wait a while.

Select the Mute Level setting you want.

This sets how much the volume is to be turned down when MUTE is pressed.
!	 FULL (default) – No sound.
!	 –40.0dB/–20.0dB – The volume will be turned down to the level specified here.

5	

3	

Check on the screen whether or not an update file was found.

If “New version found.” is displayed, the update file has been found. The version number and updating time are
displayed.
If “This is the latest version. There is no need to update.” is displayed, no update file has been found.

When you’re finished, press RETURN.

You will return to the Other Setup menu.

4	

Remote Control Mode Setup

The updating screen appears and updating is performed.
!	 The power turns off automatically once updating is completed.

!	 Default setting: 1
This sets this receiver’s remote control mode to prevent erroneous operation when multiple units of the receiver
are being used.

1	

Select ‘Remote Control Mode Setup’ from the Other Setup menu.

2	

Select the Remote Control Mode setting you want.

3	

Select ‘OK’ to change the remote control mode.

4	

Follow the instructions on the screen to change the remote control’s setting.

Software Update messages
Status messages
FILE ERROR

See Operating multiple receivers on page 70.

5	

To update, select OK.

When you’re finished, press RETURN.

You will return to the Other Setup menu.

Descriptions
Try disconnecting then reconnecting the USB device or storing the update file again. If the error still
occurs, try using a different USB memory device.
No update file was found on the USB memory device. Store the file in the USB memory device’s root
directory.

UPDATE ERROR 1 to
UPDATE ERROR 7

Turn the receiver’s power off, then turn it back on and try updating the software again.

Update via USB

If this message flashes, updating has failed. Update via a USB memory device. Put the update file on a
USB memory device and connect the device to the USB port. When the file is found, software updating
starts automatically.

UE11

Software Update

UE22

Use this procedure to update the receiver’s software and check the version. There are two ways to update: via the
Internet and via a USB memory device.
Updating via the Internet is performed by accessing the file server from the receiver and downloading the file.
This procedure is only possible if the receiver is connected to the Internet.
Updating via a USB memory device is performed by downloading the update file from a computer, reading this
file onto a USB memory device then inserting this USB memory device into the USB port on the receiver’s front
panel. With this procedure, the USB memory device containing the update file must first be inserted into the USB
port on the receiver’s front panel.

UE33

88

Updating has failed. Use the same procedure to update the software again.

　
　
　
　

12

The System Setup and Other Setup menus

8	

ZONE Setup

Select the HPF (High Pass Filter) setting you want.

This can only be set when ZONE 2 is selected in step 2.
The low frequency component output from the AUDIO ZONE 2 OUT terminals is cut. When a subwoofer is connected in Zone 2, we recommend setting this to “ON”. This is only valid when Zone 2 is connected using the
AUDIO ZONE 2 OUT terminals.
!	 OFF (default) – The High Pass Filter function is disabled.
!	 ON – The High Pass Filter function is enabled.

The volume setting and tone for the sub zones that can be used with this receiver can be changed and adjusted
here.

CAUTION
!	 Note that when Volume Level is set to 0 dB Fixed, the audio output from the AUDIO ZONE 2 OUT terminals
is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may
be produced even when Volume Level is set to –40 dB Fixed.

9	

Select the TONE setting you want.

1	

Select ‘ZONE Setup’ from the Other Setup menu.

2	

Select ‘ZONE 2’ or ‘ZONE 3’, then press ENTER.

This can only be set when ZONE 2 is selected in step 2.
The bass and treble for ZONE 2 can be adjusted. When BYPASS is selected, the original sound is played as such.
When ON is selected, the BASS and TREBLE can be adjusted.
!	 When the speaker terminals are being used for Zone 2, the TONE settings cannot be made.

3	

Select the Volume Level setting you want.

10	 Adjust the bass (BASS) and treble (TREBLE) to your tastes.

When making multi-zone connections using the AUDIO ZONE 2 OUT or AUDIO ZONE 3 OUT terminals and performing playback in Zone 2 or Zone3, you can set whether to adjust the Zone 2 or Zone3 volume on the receiver or
to fix it to a specific volume (–40 dB Fixed or 0 dB Fixed). This is set to Variable upon shipment from the factory,
allowing the volume to be adjusted on the receiver. If you would like to adjust the volume from the connected
amplifier, make the setting below.
For ZONE 2, this setting is not possible if multi-zone settings have been made using the speaker terminals and
Speaker System is set to ZONE 2. In this case, adjust the volume for the sub zones on the receiver.
!	 Variable (default) – The Zone 2/Zone3 volume is adjusted from the receiver.
!	 –40 dB Fixed/0 dB Fixed – The Zone 2/Zone 3 volume level output from the receiver is fixed to the value set
here.

4	

This can only be set when ZONE 2 is selected in step 2 and ON is selected in step 8.
The BASS and TREBLE can each be adjusted between –10.0dB and +10.0dB, in 1 dB steps.

11	 When you’re finished, press RETURN.
You will return to the Other Setup menu.

EXTENSION Setup
!	 Default setting: OFF
A separately sold the CU-RF100 can be used to operate the receiver by RF communications. To do so, set the
EXTENSION setting to ON. When ON is set here, the receiver can be operated even when the receiver is in the
standby mode.

Select the Power ON Level setting you want.

The sub zone volume is set to the volume selected here when the sub zone is turned on using the multi-zone function. Zones 2 and 3 can be set separately.
When Volume Level is set to –40 dB Fixed or 0 dB Fixed, the volume is fixed to that level, so the volume cannot
be set here.
!	 LAST (default) – When MULTI-ZONE is turned on, the volume is set to the level set the last time you were
listening to that zone.
!	“---” – When MULTI-ZONE is turned on, the volume for that zone is set to the minimum.
!	 –80.0dB to 0dB – When MULTI-ZONE is turned on, the volume is set to the level set here. The volume can be
set up to the value set at Volume Limit below.

5	

Select the Volume Limit setting you want.

Select the Mute Level setting you want.

The mute level for the zone selected in step 2 can be set.
This sets how much the volume is to be turned down when MUTE is pressed.
!	 FULL (default) – No sound.
!	 –40.0dB/–20.0dB – The volume will be turned down to the level specified here.

7	

Select ‘EXTENSION Setup’ from the Other Setup menu.

2	

Select the EXTENSION setting you want.

3	

When you’re finished, press RETURN.

You will return to the Other Setup menu.

The maximum volume for the zone selected in step 2 can be set.
!	 OFF (default) – The maximum volume is not limited.
!	 –20.0dB/–10.0dB – The maximum volume is limited to the value set here.

6	

1	

Adjust Lch Level and Rch Level.

The channel level for the zone selected in step 2 can be set.
The level can be adjusted between –12.0dB and +12.0dB, in 1 dB steps.

89

　
　
　
　

FAQ
Troubleshooting............................................................................................................................. 91
Power...............................................................................................................................................91
No sound......................................................................................................................................... 91
Other audio problems.................................................................................................................... 92
ADAPTER PORT terminal................................................................................................................ 93
Video................................................................................................................................................93
Settings............................................................................................................................................93
Professional Calibration EQ graphical output.............................................................................. 94
Display.............................................................................................................................................94
Remote control............................................................................................................................... 94
HDMI................................................................................................................................................94
AVNavigator................................................................................................................................... 95
USB interface................................................................................................................................... 96
iPod..................................................................................................................................................96
Network.......................................................................................................................................... 96
Web Control.................................................................................................................................... 97
Wireless LAN................................................................................................................................... 98

90

　
　
　
　

13

FAQ

Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong
with this component, check the points below. Sometimes the trouble may lie in another component. Investigate
the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized independent service company to carry out repair
work.
!	 If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.
If the problem is not solved after the troubleshooting below, if the screen freezes unexpectedly or if the buttons on
the remote control or front panel stop working completely, do the following:
!	Press u STANDBY/ON on the front panel to turn off the power, then turn the power back on.
!	 If the power cannot be turned off, press and hold u STANDBY/ON on the front panel for over 10 seconds. The
power will turn off. In this case, the various settings made on the receiver may be cleared. (However, settings
made when the power was turned off normally are not cleared.)

Symptom

Remedy

AMP OVERHEAT blinks in the display and the FL OFF indicator flash
and the power turns off.

Allow the unit to cool down in a well-ventilated place before switching back on (see
Installing the receiver on page 9).
Check whether the cables used to connect the speakers are short-circuited.
Wait at least 1 minute, then try turning the power on again.
The temperature within the unit has exceeded the allowablevalue.
Lower the volume level.

The receiver suddenly power off or
ADVANCED MCACC flashes.

The power unit is damaged. Unplug the receiver from the wall and call a Pioneer authorized independent service company.

FAN STOP is displayed, then
iPod iPhone iPad indicator blinks.

The built-in cooling fan is malfunctioning. Do not try switching the receiver on. Unplug
the receiver from the wall and call a Pioneer authorized independent service company.

No sound

Power

Symptom

Remedy

No sound is output when an input
function is selected.
No sound is output from the front
speakers.

Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).

Symptom

Remedy

The power does not turn on.

Make sure that the power cord is plugged in to an active power outlet.
Try disconnecting from the power outlet, then plugging back in.

Make sure the correct input signal is selected (press SIGNAL SEL).

Power cannot be turned off.
(ZONE 2 ON or ZONE 3 ON is displayed.)

Press the remote control’s ZONE 2 or ZONE 3, then press u RECEIVER to switch the sub
zone off.

Note that when Fixed PCM ON is selected, you won’t be able to hear any other signal
format (see Setting the Audio options on page 62).

The receiver suddenly switches off
or the iPod iPhone iPad indicator
blinks.

Check that there are no loose strands of speaker wire touching the rear panel or another
set of wires. If so, re-attach the speaker wires, making sure there are no stray strands.

During loud playback the power suddenly switches off.

Turn down the volume.

Check that the speakers are connected properly (see Connecting the speakers on page
21).

The receiver may have a serious problem. Disconnect from the power and call a Pioneer
authorized independent service company.

No sound from the surround or
center speakers.

Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 78.

Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t
selected; select one of the surround listening modes (see Enjoying various types of playback using the listening modes on page 49).
Check that the surround/center speakers are not set to NO (see Speaker Setting on page
84).
Check the channel level settings (see Channel Level on page 85).
Check the speaker connections (see Connecting the speakers on page 21).

No sound from surround back
speakers.

Try switching the receiver off, then back on again.
Try disconnecting the power cord, then connect again.

Check that the surround back speakers are set to LARGE or SMALL, and the surround
speakers are not set to NO (see Speaker Setting on page 84).
Check the speaker connections (see Connecting the speakers on page 21). If only one
surround back speaker is connected, make sure it’s connected to the left channel
speaker terminal.

AMP ERR blinks in the display, then The receiver may have a serious problem. Do not try switching the receiver on. Unplug the
the power automatically switches off. receiver from the wall and call a Pioneer authorized independent service company.
The ADVANCED MCACC blinks and
the power does not turn on.
The receiver suddenly switches off or
the FL OFF indicator blinks.

Check that the MCACC setup microphone is disconnected.

Check that the source component is connected properly (see Connecting your equipment
on page 18).

Switch on the digital safety feature. While holding down ENTER on the front panel,
press u STANDBY/ON to set this receiver to the standby mode. Use TUNE i/j to
select D.SAFETY cOFFd, and then use PRESET k/l to select 1 or 2 (select D.SAFETY
cOFFd to deactivate this feature). If the power switches off even with 2 switched on, turn
down the volume. With 1 or 2 on, some features may be unavailable.
The unit does not respond when the
buttons are pressed.

Make sure the correct input function is selected.

Surround back speakers will not play while the Speaker System is set to Speaker B and
audio is being played through speaker B.

There is a problem with the receiver’s power unit or fan. Try turning on the power. If the
same thing happens, the receiver is damaged. Unplug the receiver from the wall and call
a Pioneer authorized independent service company. (Other symptoms may appear when
the power is turned on.)

When Speaker System is set to Normal(SB/FH) or Normal(SB/FW) and SP: FH ON or
SP: FW ON is selected with the SPEAKERS button, no sound will be output from the surround back speakers. Select SP: SB/FH ON, SP: SB/FW ON or SP: SB ON (see Switching
the speaker terminals on page 66).

91

　
　
　
　

13

FAQ

Symptom

Remedy

Symptom

Remedy

No sound from front height or front
wide speakers.

Check that the front height or front wide speakers are set to LARGE or SMALL, and the
surround speakers are not set to NO (see Speaker Setting on page 84).

Broadcast stations cannot be
selected automatically, or there is
considerable noise in radio broadcasts.

Fully extend the FM wire antenna, adjust the position for best reception and secure to a
wall, etc.

When Speaker System is set to Normal(SB/FH) or Normal(SB/FW) and SP: SB ON is
selected with the SPEAKERS button, no sound will be output from the front height or
front wide speakers. Select SP: SB/FH ON, SP: SB/FW ON, SP: FH ON or SP: FW ON (see
Switching the speaker terminals on page 66).
Check that the subwoofer is connected properly, switched on and the volume turned up.

Noise is output when scanning a
DTS CD.

This is not a malfunction of the receiver. The scan function of your player alters the digital
information, making it unreadable, resulting in noise being output. Lower the volume
when scanning.

When playing a DTS format LD there
is audible noise on the soundtrack.

Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on
page 50).

Can’t record audio.

You can only make a digital recording from a digital source, and an analog recording
from an analog source.

If your subwoofer has a sleep function, make sure it is switched off.
Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 84).
The crossover frequency may be set too low; try setting it higher to match the characteristics of your other speakers (see Speaker Setting on page 84).
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting on page 84).

For digital sources, make sure that what you’re recording isn’t copy protected.
Subwoofer output is very low.

Check that the LFE channel is not set to OFF, or to a very quiet setting (see Setting the
Audio options on page 62).
Check the speaker connection (see Connecting the speakers on page 21).

The Phase Control feature doesn’t
seem to have an audible effect.

Check the speaker level settings (see Channel Level on page 85).
Check that the speaker hasn’t been set to NO (see Speaker Setting on page 84).
The channel may not be recorded in the source. By using one of the advanced effect
listening modes, you may be able to create the missing channel (see Enjoying various
types of playback using the listening modes on page 49).
Sound is produced from analog
components, but not from digital
ones (DVD, LD, CD, etc.).

Check that the input signal type is set to DIGITAL (see Choosing the input signal on page
50).
Make sure that the digital input is assigned correctly for the input jack the component is
connected to (see The Input Setup menu on page 39).
If the source component has a digital volume control, make sure this is not turned down.
Check that your BD or DVD player is compatible with Dolby Digital/DTS discs.

If the HDMI input function is selected, sound is muted until exiting the Home Menu.

Other audio problems
Symptom

Remedy

Speaker switching sound (clicking
sound) is heard from receiver during
playback.

Depending on the listening mode, the front height (or front wide) and surround back
speakers may switch automatically in function of changes in the input audio. A speaker
switching sound (clicking sound) will be heard from the receiver at this time. If this sound
bothers you, we recommend to change the speaker terminal option (see Switching the
speaker terminals on page 66).

Noise or hum can be heard even
when there is no sound being input.

Check that personal computers or other digital components connected to the same
power source are not causing interference.

Can’t select some Input functions by
the INPUT SELECTOR on the front
panel or the INPUT SELECT button
on the remote control.

Check the Input Skip settings in the Input Setup menu (see The Input Setup menu on
page 39).
Check the HDMI Input assignment in the Input Setup menu then try OFF (see The Input
Setup menu on page 39).

See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37 to
There seems to be a time lag
between the speakers and the output set up your system again using MCACC (this will automatically compensate for a delay in
the subwoofer output).
of the subwoofer.

Check the digital output settings or the HDMI audio output settings of your BD or DVD
player. Make sure that the DTS signal output is set to On.
If the source component has a digital volume control, make sure this is not turned down.

No sound when using the
Home Menu.

If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass
cutoff is set to the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
Make sure the speaker distance setting is correct for all speakers (see Speaker Distance
on page 85).

Check the digital output settings on the source component.
No sound is output or a noise is output when Dolby Digital/DTS software
is played back.

To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL
(see Speaker Setting on page 84).

The speakers may be out of phase. Check that the positive/negative speaker terminals on
Everything seems to be set up correctly, but the playback sound is odd. the receiver are matched with the corresponding terminals on the speakers (see Connecting the speakers on page 21).

Check the speaker level settings (see Channel Level on page 85).
No sound from one speaker.

Adjust the position and direction of the AM antenna.
Noise may be caused by interference from other equipment, such as a fluorescent light,
motor, etc. Switch off or move the other equipment, or move the AM antenna.

Check the speaker connections (see Connecting the speakers on page 21).
No sound from subwoofer.

Use an outdoor antenna for better reception (see page 31).

92

The maximum volume available
(shown in the front panel display) is
lower than the +12dB maximum.

Check that the Volume Limit is set to OFF (see Volume Setup on page 88).

Certain listening modes or
HOME MENU items cannot be
selected.

When Operation Mode is set to Basic, the Pioneer-recommended settings are made and
not all of the functions can be used. To use all of the functions without restrictions, set
Operation Mode to Expert (see Operation Mode Setup on page 40).

The channel level setting may be over 0.0dB.

　
　
　
　

13

FAQ

Symptom

ADAPTER PORT terminal
Symptom

Remedy

The Bluetooth wireless technology
device cannot be connected or operated. Sound from the Bluetooth wireless technology device is not emitted
or the sound is interrupted.

Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave
oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If
such an object is near the unit, set the unit far from it. Or, stop using the object emitting
the electromagnetic waves.
Check that the Bluetooth wireless technology device is not too far from the unit and that
obstructions are not set between the Bluetooth wireless technology device and the unit.
Set the Bluetooth wireless technology device and the unit so that the distance between
them is less than about 10 m (33 ft.) and no obstructions exist between them.
Check that the Bluetooth ADAPTER and the ADAPTER PORT of the unit are correctly
connected.

The picture's movement is unnatural. When Resolution under VIDEO PARAMETER is set to 1080/24p, the picture may not be
displayed properly for some source materials. In this case, set the resolution to something other than 1080/24p (page 64).

The Bluetooth wireless technology device may not be set to the communication mode
supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless
technology device.
Check that pairing is correct. The pairing setting was deleted from this unit or the Bluetooth wireless technology device. Reset the pairing.

Settings

Check that the profile is correct. Use a Bluetooth wireless technology device that supports
A2DP profile and AVRCP profile.

Symptom

Remedy

The Auto MCACC Setup continually
shows an error.

The ambient noise level may be too high. Keep the noise level in the room as low as
possible (see also Problems when using the Auto MCACC Setup on page 38). If the noise
level cannot be kept low enough, you will have to set up the surround sound manually
(page 84).

Video
Symptom
No image is output when an input is
selected.

When using only one surround back speaker, connect it to the SURROUND BACK L
(Single) terminals.

Remedy

To use a 5.1-channel speaker set, use the surround speakers for the surround channel,
not the surround back channel.

Check the video connections of the source component.
For HDMI, or when V.CONV is set to OFF and a TV and another component are connected with different cords (in Setting the Video options on page 64), you must connect
your TV to this receiver using the same type of video cable as you used to connect your
video component. For the component video input, however, signals are only output from
the HDMI output, so when using the component video input, set V.CONV to ON.

Make sure there are no obstacles between the speakers and the microphone.
If Reverse Phase is displayed, try the following:
— The speaker’s wiring (+ and –) may be inverted. Check the speaker connections.
— Depending on the type of speakers and their installation conditions, Reverse Phase
may be displayed even if the speakers are properly connected. If this happens, select
GO NEXT and continue.
— If the speaker is not pointed to the microphone (listening position) or when using
speakers that affect the phase (dipole speakers, reflective speakers, etc.), it may not be
possible to properly identify the polarity.

Make sure the input assignment is correct for components connected using component
video or HDMI cables (see The Input Setup menu on page 39).
Check the video output settings of the source component.
Check that the video input you selected on your TV is correct.
Some components (such as video game units) have resolutions that may not be converted. If adjusting this receiver’s Resolution setting (in Setting the Video options on page
64) and/or the resolution settings on your component or display doesn’t work, try switching V.CONV (in Setting the Video options on page 64) to OFF.
Can’t record video.

After using the Auto MCACC Setup,
the speaker size setting is incorrect.

There may have been some low frequency noise in the room from an air-conditioner,
motor, etc. Switch off all other appliances in the room and use Auto MCACC Setup again.
Depending on a number of factors (bass reproduction capabilities of the speakers, room
size, speaker placement, etc.) this may occur in some cases. Change the speaker setting
manually in Speaker Setting on page 84, and use the ALL (Keep SP System) option for
the Auto MCACC menu in Automatic MCACC (Expert) on page 76 if this is a recurring
problem.

Check that the source is not copy-protected.
The video converter is not available when making recordings. Check that the same type
of video cable is used for connecting both the recorder and the video source (the one you
want to record) to this receiver.

Noisy, intermittent, or distorted
picture.

Remedy

Video signals are not output from the When a monitor only compatible with resolutions of 480i is connected to the component
component terminal.
terminal and another monitor is connected to the HDMI terminal, the video signals may
not be output to the monitor connected to the component terminal. If this happens, do
the following:
— Turn off the power of the monitor connected to the HDMI terminal.
— Change the VIDEO PARAMETER menu RES setting (see Setting the Video options on
page 64).
— Video signals from the HDMI terminal cannot be output to the component terminals.
Input the video signals from the player or other source to the composite or component
terminals. When using the component terminal, assign it at Input Setup (see The Input
Setup menu on page 39).

Sometimes a video deck may output a noisy video signal (during scanning, for example),
or the video quality may just be poor (with some video game units, for example). The
picture quality may also depend on the settings, etc. of your display device. Switch off
the video converter and reconnect the source and display device using the same type of
connection (component or composite), then start playback again.

93

Can’t adjust the Fine Speaker Distance setting properly.

Check that the speakers are all in phase (make sure the positive (+) and negative (–)
terminals are matched up properly).

The display shows KEY LOCK ON
when you try to make settings.

With the receiver in standby, press u STANDBY/ON for about 5 seconds while holding
down SPEAKERS to disable the key lock.

Most recent settings have been
erased.

The power cord was disconnected from the wall while adjusting this setting.
Settings are only stored if all the zones are turned off. Turn off all the zones before unplugging the power cord.

　
　
　
　

13

FAQ

Symptom

Remedy

Symptom

Remedy

The various system settings are not
stored.

Do not pull out the power cord while conducting the settings. (The settings will be stored
when both the main zone and sub zone turn off. Turn off all zones before pulling out the
power cord.)

When playing certain discs, none of
the receiver’s format indicators light.

The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on
what audio tracks are recorded on the disc.

When playing a disc with the listening mode set to Auto Surround or
ALC, 2 Pro Logic II or DTS Neo:6
appear on the receiver.

Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on
page 50).

During playback of DVD-Audio, the
display shows PCM.

This will occur when playing DVD-Audio material over the HDMI connection. This is not a
malfunction.

The power turns off automatically
and some indicator flashes, or some
indicator flashes and the power does
not turn on.

See the Power section (page 91).

Certain listening modes or
HOME MENU items cannot be
selected.

When Operation Mode is set to Basic, the Pioneer-recommended settings are made and
not all of the functions can be used. To use all of the functions without restrictions, set
Operation Mode to Expert (see Operation Mode Setup on page 40).

Professional Calibration EQ graphical output
Symptom

Remedy

The reverb characteristics graph
after EQ calibration does not appear
entirely flat.

There are cases where the graph does not appear flat (even when selecting ALL CH ADJ
in the Auto MCACC Setup) due to adjustments made to compensate for room characteristics to achieve optimal sound.
Areas of the graph may appear identical (before and after) when there is little or no
adjustment needed.

Remote control

The graph may appear to have shifted vertically when comparing before and after measurements.
EQ adjustments made using the
Manual MCACC setup do not appear
to change the reverb characteristics
graph after EQ calibration.

Despite level adjustments being made, the filters used for analysis may not display these
adjustments in the reverb characteristics graph after EQ calibration. However, these
adjustments are taken into account by the filters dedicated to overall system calibration.

Lower frequency response curves do
not seem to have been calibrated for
SMALL speakers.

Low frequencies used in bass management (the subwoofer channel) will not change for
speakers that have been specified as SMALL in the configuration, or do not output these
frequencies.

If a two channel soundtrack is currently playing (including Dolby Surround encoded),
then this is not a malfunction. Check the disc packaging for details about the audio
tracks available.

Symptom

Remedy

Cannot be remote controlled.

Set the remote control unit’s remote control mode so that it matches the setting on the
main unit (see Operating multiple receivers on page 70).
Check whether the receiver’s remote control mode is properly set (see Remote Control
Mode Setup on page 88).
Try replacing the batteries in the remote control (see Loading the batteries on page 9).
Be sure to operate within 7 m (23 ft.) and a 30º angle of the remote sensor on the front
panel (see Operating range of remote control unit on page 9).

Calibration is performed, but due to your speakers’ low frequency limitations, no measurable sound is output for display.

Check that there are no obstacles between the receiver and the remote control.
Make sure that there is no fluorescent or other strong light shining on to the remote
sensor.
Other components can’t be operated
with the system remote.

Display

If the battery ran down, the preset codes may have been cleared. Re-enter the preset
codes.

Symptom

Remedy

The preset code may be incorrect. Redo the procedure for entering preset codes.

The display is dark or off.

Press DIMMER repeatedly to select a different brightness.

The OSD screen is not displayed.

The OSD screen is not displayed unless the receiver and TV are connected using an
HDMI cable. If the TV does not support HDMI, perform the various operations and make
the settings while watching the display on the receiver’s front panel.

When commands from the remote control units of other devices are registered using the
learning function, in some cases they may not be learned properly. In this case, register
the commands again using the learning function (see page 71). If they still do not work,
they may be in a special format that cannot be registered on this receiver’s remote control. Operate the device using another remote control.

You can’t get DIGITAL to display
when using SIGNAL SEL.

Check the digital connections and make sure that the digital inputs are assigned correctly (see The Input Setup menu on page 39).

2 DIGITAL or DTS does not light
when playing Dolby/DTS software.

These indicators do not light if playback is paused.

HDMI

Check the playback (especially the digital output) settings of the source component.

When playing Dolby Digital or DTS
Check that the player is connected using a digital connection.
sources, the receiver’s format indica- Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on
tors do not light.
page 50).
Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to
PCM.
Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is
selected.

94

Symptom

Remedy

The HDMI indicator blinks continuously.

Check all the points below.

　
　
　
　

13

FAQ

Symptom

Remedy

No picture or sound.

This receiver is HDCP-compatible. Check that the components you are connecting are
also HDCP-compatible. If they are not, please connect them using the component or
composite video jacks.

AVNavigator

Depending on the connected source component, it’s possible that it will not work with
this receiver (even if it is HDCP-compatible). In this case, connect using the component
or composite video jacks between source and receiver.

Symptom

Causes

Remedy

AVNavigator cannot be
installed.

An error message may appear
if there are not enough system
resources available.

Re-start the PC, then start install with no other applications
active.

Installation of AVNavigator may fail
because of incompatibilities with
other applications.

Try the following, in the order indicated.
1. If there are any other applications active, exit the other
applications and try to start install again.
2. If that does not work, try restarting your PC, then start
install with no other applications active.

The receiver’s power is not turned
on.

Turn the receiver’s power on. (Wait about 60 seconds after
the power turns on for network functions to start.)
After this, press Detection in AVNavigator to redetect the
receiver.

The receiver or computer is not connected to the LAN.

Connect a LAN cable to the receiver or computer (page 32).
After this, press Detection in AVNavigator to redetect the
receiver.

The router’s power is off.

Turn the router’s power on.
After this, press Detection in AVNavigator to redetect the
receiver.

AVNavigator’s network settings are
not correct.

If your router does not support DHCP, the receiver’s
IP address must be set in AVNavigator. First set the IP
address on the receiver, then set the same address in
AVNavigator (page 86).
After this, press Detection in AVNavigator to redetect the
receiver.

Network connections could be
restricted due to the computer’s network settings, security settings, etc.

Check the computer’s network settings, security settings,
etc.
After this, press Detection in AVNavigator to redetect the
receiver.

When the operating instructions
interactive mode is changed, the
settings may not be transferred to
the browser, causing AVNavigator to
stop interacting.

Either refresh the page’s display using the browser’s
refresh button or display a different page from the links so
that the setting is transferred.

If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
If video images do not appear on your TV, try adjusting the resolution, Deep Color or other
setting for your component.

AVNavigator does not interact well with the receiver.

While analog video signals are being output over HDMI, use a separate connection for
audio output.
To output signals in Deep Color, use an HDMI cable (High Speed HDMI® Cable) to connect this receiver to a component or TV with the Deep Color feature.
No picture.

Try changing the Resolution setting (in Setting the Video options on page 64).

No sound, or sound suddenly
ceases.

Check that the HDMI Audio setting is set to AMP (Setting the Audio options on page 62).
If the component is a DVI device, use a separate connection for the audio.
If analog video is being output over HDMI, please use a separate connection for the
audio.
Check the audio output settings of the source component.
HDMI format digital audio transmissions require a longer time to be recognized. Due
to this, interruption in the audio may occur when switching between audio formats or
beginning playback.
Turning on/off the device connected to this unit’s HDMI OUT terminal during playback,
or disconnecting/connecting the HDMI cable during playback, may cause noise or interrupted audio.

Noisy or distorted picture.

Sometimes a video deck may output a noisy video signal (during scanning, for example),
or the video quality may just be poor (with some video game units, for example). The
picture quality may also depend on the settings, etc. of your display device. Switch off
the video converter and reconnect the source and display device using the same type of
connection (component or composite), then start playback again.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.

HDCP ERROR shows in the display.

Check whether or not the connected component is compatible with HDCP. If it is not
compatible with HDCP, reconnect the source device using a different type of connection
(component or composite). Some components that are compatible with HDCP still cause
this message to be displayed, but so long as there is no problem with displaying video,
this is not a malfunction.

Synchronized operation not possible
using Control with HDMI function.

Check the HDMI connections.
The cable may be damaged.
Select ON for the Control Mode with HDMI setting (see HDMI Setup on page 59).
Turn the TV’s power on before turning on this receiver’s power.
Set the TV side Control with HDMI setting to on (see TV’s operating instructions).

95

This is because of the browser’s
When the Wiring Navi,
Operation Guide,
security function.
Interactive Manual, Glossary
or Software Update is
launched, a warning about
security protection appears
on the browser.

This is not a problem. Perform the operation to authorize
the blocked contents.

Software updating does not
operate well.

Contact your contracted provider.

There may be a problem with your
Internet Service Provider’s network.

　
　
　
　

13

FAQ

USB interface
Symptoms

Network
Causes

The folders/files stored on a The folders/files are currently stored
USB memory device are not in a region other than the FAT (File
displayed.
Allocation Table) region.

A USB memory device is
not recognized.

Remedies

Symptoms

Causes

Remedies

Store the folders/files in the FAT region.

Cannot access the network.

The LAN cable is not firmly connected.

Firmly connect the LAN cable (page 32).

The router is not switched on.

Switch on the router.

Internet security software is currently installed in the connected
component.

There are cases where a component with Internet security
software installed cannot be accessed.

The audio component on the network which has been switched off is
switched on.

Switch on the audio component on the network before
switching on this receiver.

The number of levels in a folder is
more than 9.

Limit the maximum number of levels in a folder to 9 (page
44).

The audio files are copyrighted.

Copyrighted audio files stored on a USB memory device
cannot be played back (page 44).

The USB memory device does not
support the mass storage class
specifications.

Try using a USB memory device compatible with the mass
storage class specifications. Note that there are cases
where even the audio files stored on a USB memory device
compatible with the mass storage class specifications are
not played back on this receiver (page 44).

Playback does not start
while “Connecting...” continues to be displayed.

The component is currently disconnected from this receiver or the
power supply.

Check whether the component is properly connected to
this receiver or the power supply.

Connect the USB memory device and switch on this
receiver (page 33).

The PC or Internet radio is
not properly operated.

The corresponding IP address is not
properly set.

Switch on the built-in DHCP server function of your router,
or set up the network manually according to your network
environment (page 86).

The IP address is being automatically configured.

The automatic configuration process takes time. Please
wait.

Windows Media Player 11 or
Windows Media Player 12 is not currently installed on your PC.

Install Windows Media Player 11 or Windows Media Player
12 on your PC (page 53).

Audio files recorded in MPEG-4
AAC or FLAC are being played back
on Windows Media Player 11 or
Windows Media Player 12.

Audio files recorded in MPEG-4 AAC or FLAC cannot be
played back on Windows Media Player 11 or Windows
Media Player 12. Try using another server. Refer to the
operation manual supplied with your server.

The component connected to the
network is not properly operated.

Check whether the component is affected by special circumstances or is in the sleep mode.
Try rebooting the component if necessary.

The component connected to the
network does not permit file sharing.

Try changing the settings for the component connected to
the network.

The folder stored on the component
connected to the network has been
deleted or damaged.

Check the folder stored on the component connected to
the network.

Network connections could be
restricted due to the computer’s network settings, security settings, etc.

Check the computer’s network settings, security settings,
etc.

The component connected to the
network is not properly set.

If the client is automatically authorized, you need to enter
the corresponding information again. Check whether the
connection status is set to “Do not authorize”.

There are no playable audio files on
the component connected to the
network.

Check the audio files stored on the component connected
to the network.

A USB hub is currently being used.

This receiver does not support USB hubs (page 44).

This receiver recognizes the USB
memory device as a fraud.

Switch off and on again this receiver.
Reconnect the USB device with the receiver switched off.
The audio files stored on
components on the network, such as a PC, cannot
be played back.

Change to an input other than iPod/USB, then set the input
back to iPod/USB.
A USB memory device is
connected and displayed,
but the audio files stored
on the USB memory device
cannot be played back.

Some formats of USB memory
devices, including FAT 12, NTFS, and
HFS, cannot be played back on this
receiver.

Check whether the format of your USB memory device is
either FAT 16 or FAT 32. Note that the FAT 12, NTFS, and
HFS formats cannot be played back on this receiver (page
44).

The file format cannot be properly
played back on this receiver.

See the list of file formats that can be played back on this
receiver (page 45).

iPod
Symptoms

Causes

Remedies

iPod is not recognized.

This receiver recognizes the iPod as
a fraud.

Switch off and on again this receiver.
Reconnect the iPod with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
Cannot access the component connected to the
network.

96

　
　
　
　

13

FAQ

Symptoms

Causes

Remedies

Audio playback is undesirably stopped or disturbed.

The audio file currently being played
back was not recorded in a format
playable on this receiver.

Check whether the audio file was recorded in a format supported by this receiver.
Check whether the folder has been damaged or corrupted.
Note that there are cases where even the audio files listed
as playable on this receiver cannot be played back or
displayed (page 57).

The LAN cable is currently disconnected.

Connect the LAN cable properly (page 32).

There is heavy traffic on the network
with the Internet being accessed on
the same network.

Use 100BASE-TX to access the components on the network.

Web Control

There is a connection routed through There may be a shortage of bandwidth on the 2.4 GHz band
a wireless LAN on the same network. used by the wireless LAN. Make wired LAN connections not
routed through a wireless LAN.
Install away from any devices emitting electromagnetic
waves on the 2.4 GHz band (microwave ovens, game consoles, etc.). If this does not solve the problem, stop using
other devices that emit electromagnetic waves.
In case of Windows Media Player
11: You are currently logged onto
the domain through your PC with
Windows XP or Windows Vista
installed.
In case of Windows Media Player
12: You are currently logged onto
the domain through your PC with
Windows 7 installed.

Instead of logging onto the domain, log onto the local
machine (page 54).

Cannot listen to Internet
radio stations.

The firewall settings for components
on the network are currently in
operation.

Check the firewall settings for components on the network.

You are currently disconnected from
the Internet.

Check the connection settings for components on the
network, and consult with your network service provider if
necessary (page 86).

The broadcasts from an Internet
radio station are stopped or interrupted.

There are cases where you cannot listen to some Internet
radio stations even when they are listed in the list of Internet radio stations on this receiver (page 54).

The remote control is not currently
set to the Network function mode.

Press NET to set the remote control to the Network function mode (page 54).

The Network functions
cannot be operated with
the buttons on the remote
control.

Causes

Remedies

Web Control screen is not
displayed on browser.

This receiver’s IP address has not
been entered into the browser correctly.

Check the receiver’s IP address and enter it correctly in the
browser (page 86).

Receiver settings cannot be
made from a browser.

JavaScript is disabled on the internet Enable JavaScript.
browser.
The browser is not compatible with
JavaScript.

When in the DMR mode, depending In this case, adjust the volume from the receiver or remote
on the external controller being used, control.
playback may be interrupted when a
volume operation is performed from
the controller.

Cannot access Windows
Media Player 11 or
Windows Media Player 12.

Symptoms

97

Use an internet browser that is compatible with JavaScript.

　
　
　
　

13

FAQ

Try making the wireless LAN converter’s advanced settings.
!	 The wireless LAN converter can be connected to a computer to make the advanced wireless LAN settings.
For details, see the CD-ROM included for the wireless LAN converter. Check the settings of the wireless
LAN router, etc., then change the settings of the wireless LAN converter.
	 Note, however, that making the advanced wireless LAN settings will not necessarily improve the wireless
LAN environment. Be careful when changing the settings.

Wireless LAN
Network cannot be accessed via wireless LAN.
Wireless LAN converter’s power is not on. (Wireless LAN converter’s “Power”, “WPS” and “Wireless” indicators are not all lit.)
!	 Check that the USB cable connecting the wireless LAN converter to the receiver’s DC OUTPUT for
WIRELESS LAN terminal is properly connected.

The access point is set to conceal the SSID.
!	 In this case, the SSID may not be displayed on the access point list screen. If not, set the SSID, etc., by
making the wireless LAN converter settings on the receiver manually.

WLAN POW ERR is displayed on the receiver’s display window.
!	 There is a problem with the wireless LAN converter’s power supply. Turn the receiver’s power off, then
disconnect the USB cable, reconnect the USB cable and turn the receiver’s power back on.
!	If WLAN POW ERR is still displayed after repeating the above procedure several times, there is a problem
with the receiver or the USB cable. Unplug the receiver from the wall and call a Pioneer authorized independent service company.

The access point’s security settings use WEP 152-bit length code key or shared key authentication.
!	 The receiver does not support WEP 152-bit length code key or shared key authentication.
Network connections cannot be established even when the above measures are taken.
!	 Reset the wireless LAN converter. After this, redo the wireless LAN converter’s settings.
	 About resetting
	 1. Check that the wireless LAN converter’s power is on.
	 2. Press the wireless LAN converter’s reset button for at least 3 seconds.
	 3. Release the reset button.
	 When the wireless LAN converter is restarted, the resetting procedure is completed.

The LAN cable is not firmly connected.
!	 Firmly connect the LAN cable (page 34).
Wireless LAN converter and base unit (wireless LAN router, etc.) are too far apart or there is an obstacle
between them.
!	 Improve the wireless LAN environment by moving the wireless LAN converter and base unit closer
together, etc.
There is a microwave oven or other device generating electromagnetic waves near the wireless LAN
environment.
!	 Use the system in a place away from microwave ovens or others device generating electromagnetic
waves.
!	 Avoid using devices generating electromagnetic waves as much as possible when using the system with
the wireless LAN.
Multiple wireless LAN converters are connected to the wireless LAN router.
!	 When connecting multiple wireless LAN converters, their IP addresses must be changed.
Wireless LAN connections cannot be established between the wireless LAN converter and base unit (wireless
LAN router, etc.).
!	 The wireless LAN converter must be set in order to establish wireless LAN connections. For details, see
the CD-ROM included with the wireless LAN converter.
The IP address settings of the receiver and wireless LAN converter do not match the settings of the wireless
LAN router, etc.
!	 Check the IP address settings of the receiver and wireless LAN converter (including the DHCP setting).
	 If the receiver’s DHCP setting is “ON”, turn the receiver’s power off, then turn the power back on.
	 Check that the IP addresses of the receiver and wireless LAN converter match the settings of the wireless
LAN router, etc.
	 If the receiver’s DHCP setting is “OFF”, set an IP address matching the network of the base unit (wireless
LAN router, etc.).
	 For example, if the wireless LAN router’s IP address is “192.168.1.1”, set the receiver’s IP address to
“192.168.1.XXX” (*1), the subnet mask to “255.255.255.0”, the gateway and DNS to “192.168.1.1”.
	 Next, set the wireless LAN converter’s IP address to “192.168.1.249” (*2).
	 (*1) Set the “XXX” in “192.168.1.XXX” to a number between 2 and 248 that is not assigned to other devices.
	 (*2) Set the “249” in “192.168.1.249” to a number between 2 and 249 that is not assigned to other devices.

98

　
　
　
　

Additional information
Surround sound formats..............................................................................................................100
About iPod....................................................................................................................................100
About SiriusXM.............................................................................................................................100
About FLAC...................................................................................................................................100
Windows 7....................................................................................................................................101
Auto Surround, ALC and Stream Direct with different input signal formats.......................... 101
Speaker Setting Guide................................................................................................................. 102
About messages displayed when using network functions..................................................... 103
Important information regarding the HDMI connection.......................................................... 103
Cleaning the unit..........................................................................................................................103
Preset code list..............................................................................................................................109

99

　
　
　
　

14

Additional information

Surround sound formats

About SiriusXM

Below is a brief description of the main surround sound formats you’ll find on BDs, DVDs, satellite, cable and
terrestrial broadcasts, and video cassettes.

Dolby
The Dolby technologies are explained below. See http://www.dolby.com for more detailed information.
Hardware and subscription sold separately. SiriusXM service automatically renews and you will be billed, at thencurrent rates, until you call us at 1-866-635-2349 to cancel.
See our Customer Agreement for complete terms at www.siriusxm.com.
Canadian service available at www.sirius.ca or www.xmradio.ca.
Be sure to read these agreements before you purchase your subscription.
Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “Surround EX” and the double-D symbol
are trademarks of Dolby Laboratories.

About FLAC

DTS

FLAC Decoder

The DTS technologies are explained below. See http://www.dts.com for more detailed information.

Copyright © 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007
Josh Coalson
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the
following conditions are met:
!	 Redistributions of source code must retain the above copyright notice, this list of conditions and the following
disclaimer.
!	 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
!	 Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or
promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929;
7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS-HD and
the Symbol together are registered trademarks & DTS-HD Master Audio is a trademark of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved.

About iPod

“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to
connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless
performance.
Apple, AirPlay, iPad, iPhone, iPod, iPod nano, iPod touch, iTunes and Mac are trademarks of Apple Inc., registered in
the U.S. and other countries.
The AirPlay logo is a trademark of Apple Inc.

100

　
　
　
　

14

Additional information

Windows 7

Auto Surround, ALC and Stream Direct with different input signal
formats
The following charts show what you will hear with different input signal formats, depending on the Stream Direct
mode (see Using Stream Direct on page 50) you have selected.

Stereo (2 channel) signal formats
Auto Surround / ALC /
DIRECT

PURE DIRECT

Dolby Digital Surround

2 Pro Logic IIx MOVIE

2 Pro Logic IIx MOVIE

DTS Surround

Neo:6 CINEMA

Neo:6 CINEMA

Other stereo sources

Stereo playback

Stereo playback

Analog sources

As above

ANALOG DIRECT (stereo)

PCM sources

As above

Stereo playback

DVD-A sources

As above

As above

SACD sources

As above

As above

Dolby Digital Surround

2 Pro Logic II MOVIE

2 Pro Logic II MOVIE

DTS Surround

Neo:6 CINEMA

Neo:6 CINEMA

Other stereo sources

Stereo playback

Stereo playback

Analog sources

As above

ANALOG DIRECT (stereo)

PCM sources

As above

Stereo playback

DVD-A sources

As above

As above

SACD sources

As above

As above

Auto Surround / ALC

PURE DIRECT / DIRECT

Dolby Digital EX
2 Pro Logic IIx MOVIE


Dolby Digital EX
2 Pro Logic IIx MOVIE


Input signal format
Surround Back speaker(s): Connected

Windows and the Windows logo are trademarks of the Microsoft group of companies.

Surround Back speaker(s): Not connected

Multichannel signal formats
Input signal format
Surround Back speaker(s): Connected
Dolby Digital EX (6.1 channel flagged)
Dolby TrueHD EX (6.1 channel flagged)
DTS-HD Master Audio ES (6.1 channel flagged)

DTS-ES (Matrix)

DTS-ES (Matrix)

DTS-ES (6.1 channel sources/6.1 channel flagged)

DTS-ES (Matrix/Discrete)

DTS-ES (Matrix/Discrete)

DTS sources (5.1 channel encoding)

Straight decoding

Straight decoding

DTS-HD sources

As above

As above

Other 5.1/6.1/7.1 channel sources

As above

As above

Surround Back speaker(s): Not connected
DVD-A sources/Multi-ch PCM

Straight decoding

Straight decoding

SACD sources (5.1 channel encoding)

As above

As above

Other 5.1/6.1/7.1 channel sources

As above

As above

a	 Unavailable with only one surround back speaker connected.

101

　
　
　
　

14

Additional information

Also note that placing it near a wall may result in sympathetic vibrations with the building that could excessively
amplify the bass sound.
If the subwoofer must be installed near a wall, place it at an angle so that it is not parallel to the wall surface. This
can help reduce any sympathetic vibrations, but depending on the shape of the room this could result in standing waves. However, even if standing waves are generated, their influence on the sound quality can be prevented
using the Auto MCACC’s standing wave control function (page 79).

Speaker Setting Guide
In order to achieve an even better surround effect, it is important to accurately position the speakers and make
their volume and tone characteristics uniform so as to finely focus the multi-channel sound.
The three major elements in positioning the speakers are distance, angle and orientation (the direction in
which the speakers are pointing).
Distance: The distance of all the speakers should be equal.
Angle: The speakers should be horizontally symmetrical.
Orientation: The orientation should be horizontally symmetrical.
In most homes, however, it is not possible to achieve this environment. For the distance, on this receiver it is possible to automatically correct the speaker distance electrically to a precision of 1 cm (0.5 inch) using the Full Auto
MCACC Setup function (page 37).

Step 5: Default settings with the Auto MCACC Setup (auto sound field
correction) function
It is more effective to perform the Full Auto MCACC Setup (page 37) procedure once the adjustments described
above have been completed.

Note

Step 1: Speaker layout and distance adjustment

!	 The distance to the subwoofer may be slightly larger than the distance actually measured with a tape measure,
etc. This is because this distance is corrected for electric delay, and is not a problem.

Use speaker stands or the like to make sure the speakers are steady, and leave at least 10 cm (4 inches) from the
surrounding walls. Position the speakers attentively so that the speakers on the left and right are at equal angles
from the listening position (center of the adjustments). (We recommend using cords, etc., when adjusting the
layout.) Ideally all the speakers should be equidistant from the listening position.

Positional relationship between speakers and monitor
Position of front speakers and monitor

Note

The front speakers should be as equidistant as possible to the monitor.

!	 If the speakers cannot be set at equal distances (on a circle), use the Auto MCACC Setup speaker distance
correction and Fine Speaker Distance functions to make them equalize the distance artificially.

Step 2: Adjusting the speaker height

R

L

Adjust the heights (angles) of the different speakers.
Adjust so that the front speaker units reproducing mid- and high frequencies is roughly at the height of the ears.
If the center speaker cannot be set at the same height as the front speakers, adjust its angle of elevation to point
it to the listening position.
Set surround speaker 1 so that it is not under the height of the ears.

45° to 60°

Step 3: Adjusting the speaker orientation
If the left and right speakers are not pointing in the same direction, the tone will not be the same on the right
and left, and as a result the sound field will not be reproduced properly. However, if all the speakers are pointed
towards the listening position, the sound field will seem cramped. Testing by the Pioneer Multi-channel Research
Group has shown that a good sense of sound positioning can be achieved by pointing all the speakers towards
an area 30 cm (12 inches) to 80 cm (31 inches) behind the listening position (between the surround speakers and
the listening position).
However, the sense of sound positioning can differ according to the conditions in the room and the speakers
being used. In smaller environments in particular (when the front speakers are close to the listening position),
with this method the speakers will be pointed too inward. We suggest you use this example of installation as
reference when trying out different installation methods.

Position of center speaker and monitor
Since mostly dialogs are output from the center speaker, keeping the center speaker as close as possible to the
screen makes the overall sound more natural. For TVs using Braun tubes, however, when installing the center
speaker on the floor, adjust its angle of elevation to point it towards the listening position.
Installation on floor

(Diagram as seen
from the side)
Monitor

Step 4: Positioning and adjusting the subwoofer
Placing the subwoofer between the center and front speakers makes even music sources sound more natural (if
there is only one subwoofer, it doesn’t matter if it is placed on the left or right side). The low bass sound output
from the subwoofer is not directional and there is no need to adjust the height. Normally the subwoofer is placed
on the floor. Put it in a position at which it will not cancel out the bass sound output from the other speakers.

!	 If the center speaker is not of the shielded type, install it away from the TV.
!	 When installing the center speaker on top of the monitor, place it facing slightly downwards towards the listening position.

102

　
　
　
　

14

Additional information

About messages displayed when using network functions

Important information regarding the HDMI connection

Refer to the following information when you come up with a status message while operating the Network
functions.

There are cases where you may not be able to route HDMI signals through this receiver (this depends on
the HDMI-equipped component you are connecting-check with the manufacturer for HDMI compatibility
information).
If you aren’t receiving HDMI signals properly through this receiver (from your component), please try one of the
following configurations when connecting up.

Status messages

Descriptions

Connection Down

The selected category or Internet radio station cannot be accessed.

File Format Error

Cannot be played back for some reasons.

Track Not Found

The selected song has not been found anywhere on the network.

Server Error

The selected server cannot be accessed.

Server Disconnected

The server has been disconnected.

Empty

There are no files stored in the selected folder.

License Error

The license for the contents to be played back is invalid.

Item Already Exists

This is displayed when the file you have attempted to register in the Favorites folder has
already been registered.

Favorite List Full

This is displayed when you have attempted to register a file in the Favorites folder but the
Favorites folder is already full.

Configuration A
Use component video cables to connect the video output of your HDMI-equipped component to the receiver’s
component video input. The receiver can then convert the analog component video signal to a digital HDMI signal for transmission to the display. For this configuration, use the most convenient connection (digital is recommended) for sending audio to the receiver. See the operating instructions for more on audio connections.

Note
!	 The picture quality will change slightly during conversion.

Configuration B
Connect your HDMI-equipped component directly to the display using an HDMI cable. Then use the most convenient connection (digital is recommended) for sending audio to the receiver. See the operating instructions for
more on audio connections. Set the display volume to minimum when using this configuration.

Note
!	 If your display only has one HDMI terminal, you can only receive HDMI video from the connected component.
!	 Depending on the component, audio output may be limited to the number of channels available from the
connected display unit (for example audio output is reduced to 2 channels for a monitor with stereo audio
limitations).
!	 If you want to switch the input function, you’ll have to switch functions on both the receiver and your display
unit.
!	 Since the sound is muted on the display when using the HDMI connection, you must adjust the volume on the
display every time you switch input functions.

Cleaning the unit
!	 Use a polishing cloth or dry cloth to wipe off dust and dirt.
!	 When the surface is dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with
water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleansers.
!	 Never use thinners, benzene, insecticide sprays or other chemicals on or near this unit, since these will corrode the surface.

103

　
　
　
　

14

Additional information

Decoding

Glossary

A technology for converting digital signals that have been compressed upon recording by a digital signal processing circuit, etc., into the original signals. The term “decoding” (or “matrix decoding”) is also used for the technology which converts 2-channel sound sources into multiple channels or expands 5.1-channel signals into 6.1 or
7.1 channels.

Audio formats/Decoding
Dolby
The Dolby technologies are explained below. See http://www.dolby.com for more detailed information.

Calibrating the sound field/Improving the sound quality

Dolby Digital

Phase Control

Dolby Digital is a multichannel digital audio coding system widely used in cinemas, and in the home for DVD and
digital broadcast soundtracks.

The Phase Control technology incorporated into this receiver’s design provides coherent sound reproduction
through the use of phase matching for an optimal sound image at your listening position.

Dolby TrueHD

Virtual Surround Back

Dolby TrueHD is the lossless encoding technology developed for high-definition optical discs in the upcoming
era.

When you’re not using surround back speakers, selecting this mode allows you to hear a virtual surround back
channel through your surround speakers. You can choose to listen to sources with no surround back channel
information.

Dolby Digital Plus
Dolby Digital Plus is the audio technology for all high-definition programming and media. It combines the efficiency to meet future broadcast demands with the power and flexibility to realize the full audio potential expected
in the upcoming high-definition era.

Virtual Height
When you’re not using front height speakers, selecting this mode allows you to hear a virtual front height channel
through your front speakers.

Dolby Digital Surround EX

Virtual Wide

Dolby Digital Surround EX (the EX stands for EXtended) is an extension of Dolby Digital encoding whereby a
surround back channel is matrixed into the surround left/right channels for 6.1 channel playback. This allows for
compatibility with Dolby Digital 5.1 channel decoding, as well as for decoding using Dolby Digital EX.

When you’re not using front wide speakers, selecting this mode allows you to hear a virtual front wide channel
through your front speakers.

Virtual Depth

Dolby Pro Logic IIx and Dolby Surround

When this mode is selected, the sound field expands virtually to behind the display, resulting in a sound field with
the same depth as the 3D picture to achieve a better sense of presence.

Dolby Pro Logic IIx is an improved version of the Dolby Pro Logic II (and Dolby Pro Logic) decoding system.
Dolby Surround is an encoding system which embeds surround sound information within a stereo soundtrack,
which a Dolby Pro Logic decoder can then use for enhanced surround listening with greater sound detail.

Auto Sound Retriever
The Auto Sound Retriever feature employs DSP technology to restore sound pressure and smooth jagged artifacts left over after compression.
With some audio inputs, the Sound Retriever effect is automatically optimized based on the bitrate information of
the contents that have been input to achieve high sound quality.

Dolby Pro Logic IIz
Adding a pair of speakers above the front left and right speakers adds expressiveness in the vertical direction to
the previous horizontally-oriented sound field. The height channel strengthens the sound field’s sense of threedimensionality and air, producing presence and expansion.

Sound Retriever Air

DTS

Sound Retriever Air compensates for reduced sound quality due to compression when sending Bluetooth signals.

The DTS technologies are explained below. See http://www.dts.com for more detailed information.

PQLS

DTS Digital Surround

Jitterless high quality playback is possible by connecting a PQLS-compatible player with HDMI connections.

DTS Digital Surround is a 5.1-channel audio coding system from DTS Inc. now widely used for DVD-Video, DVDAudio, 5.1 music discs, digital broadcasts, and video games.

ALC (Auto Level Control)
In the Auto level control (ALC) mode, this receiver equalizes playback sound levels.
Also, the low and high frequency sounds, dialogs, surround effects, etc., that are difficult to hear when the volume is low are adjusted to be optimal for the volume level. This mode is particularly optimum when listening at
night.

DTS-HD Master Audio
DTS-HD Master Audio is a technology that delivers master audio sources recorded in a professional studio to
listeners without any loss of data, preserving audio quality.

DTS-HD High Resolution Audio

Front Stage Surround Advance

A high definition audio technology by which signals can be transferred over HDMI cables.

With the Front Stage Surround Advance feature, you can enjoy seamless, natural surround sound effects using
only the front speakers, without deteriorating the quality of the original sound.

DTS-ES
DTS-ES (the ES stands for Extended Surround) is a decoder that is capable of decoding both DTS-ES Discrete 6.1
and DTS-ES Matrix 6.1 encoded sources.

MCACC
The Auto MCACC Setup provides a quick but accurate surround sound setup, which includes the advanced features of Professional Acoustic Calibration EQ.

DTS Neo:6
DTS Neo:6 can generate 7.1 channel surround sound from any matrixed stereo source (such as video or TV) and
from 5.1 channel sources.

104

　
　
　
　

14

Additional information

HDMI

Windows Media Player 11/Windows Media Player 12
Windows Media Player is software to deliver music, photos and movies from a Microsoft Windows computer to
home stereo systems and TVs.
With this software, you can play back files stored on the PC through various devices wherever you like in your
home.
This software can be downloaded from Microsoft’s website.
!	 Windows Media Player 11 (for Windows XP or Windows Vista)
!	 Windows Media Player 12 (for Windows 7)
For more information check the official Microsoft website.

Control with HDMI function
Synchronized operations below with a Control with HDMI-compatible Pioneer TV or Blu-ray Disc player are possible when the component is connected to the receiver using an HDMI cable.
!	 The receiver’s volume can be set and the sound can be muted using the TV’s remote control.
!	 The receiver’s input switches over automatically when the TV’s input is changed or a Control with HDMIcompatible component is played.
!	 The receiver’s power is also set to standby, when the TV’s power is set to standby.

ARC (Audio Return Channel)

Windows Media DRM

When a TV supporting the HDMI ARC (Audio Return Channel) function is connected to the receiver, the sound of
the TV can be input via the HDMI OUT terminal.
The sound of the TV can be input from the receiver’s HDMI OUT terminal, so connection with the TV can be completed with a single HDMI cable.

Windows Media DRM is a DRM (Digital Rights Management) service for the Windows Media platform. It is
designed to provide secure delivery of audio and/or video content over an IP network to a PC or other playback
device in such a way that the distributor can control how that content is used. The WMDRM-protected content
can only be played back on a component supporting the WMDRM service.

Router

Network function

A device for relaying data flowing on a network to another network. In homes, routers often also function as
DHCP servers. Products with built-in wireless LAN access points are called “wireless LAN routers”.

AirPlay
This receiver supports AirPlay audio streaming from iPod touch 2G/3G/4G, iPhone, iPhone 3G, iPhone 3GS,
iPhone 4, iPhone 4S, iPad, iPad 2 with iOS 4.2 or later, and iTunes 10.1 (Mac and PC) or later.
For more information, see the Apple website (http://www.apple.com).

DHCP
Abbreviation of Dynamic Host Configuration Protocol. A protocol for automatically assigning such setting information as IP addresses within network connections. This offers convenience in that, when enabled, it allows
network functions to be used simply by connecting the devices to the network.

DLNA
The Digital Living Network Alliance (DLNA) is a cross-industry organization of consumer electronics, computing industry and mobile device companies. Digital Living provides consumers with easy sharing of digital media
through a wired or wireless network in the home.

Wireless LAN/Wi-Fi
“Wi-Fi” (Wireless Fidelity) is a trademark coined by the Wi-Fi Alliance trade association to increase recognition
of wireless LAN standards. With the increase in the number of devices connected to computers in recent years,
Wi-Fi offers the advantage of eliminating the complexity of making connections with LAN cables by using wireless connection. As a way of reassuring users, products that have passed interoperability tests carry the logo
“Wi-Fi Certified” to indicate that compatibility is assured.

vTuner
vTuner is a paid online database service that allows you to listen to radio and TV broadcasts on the Internet.
vTuner lists thousands of stations from over 100 different countries around the globe. For more detail about
vTuner, visit the following website:
http://www.radio-pioneer.com
“This product is protected by certain intellectual property rights of NEMS and BridgeCo. Use or distribution of
such technology outside of this product is prohibited without a license from NEMS and BridgeCo or an authorized
subsidiary.”

WPS
Abbreviation of Wi-Fi Protected Setup. A standard established by the Wi-Fi Alliance industry group for a function
allowing settings related to interconnection of WPS-compatible wireless LAN devices and encryption to be made
with simple operations. There are a number of methods, including push-button configuration and PIN code configuration. This AV receiver supports both push-button configuration and PIN code configuration.

aacPlus

SSID

AAC decoder uses aacPlus developed by Coding Technologies. (www.codingtechnologies.com)

Abbreviation of Service Set IDentifier. A wireless LAN access point identifier. Can be set as desired using up to 32
characters of English letters and numbers.

FLAC
FLAC (Free Lossless Audio Codec) is an audio format allows lossless codec. Audio is compressed in FLAC without any loss in quality. For more details about FLAC, visit the following website:
http://flac.sourceforge.net/

Windows Media
Windows Media is a multimedia framework for media creation and distribution for Microsoft Windows. Windows
Media is either a registered trademark or trademark of Microsoft Corporation in the U.S. and/or other countries.
Use an application licensed by Microsoft Corporation to author, distribute, or play Windows Media formatted
content. Using an application unauthorized by Microsoft Corporation is subject to malfunction.

105

　
　
　
　

14

Additional information

　
　
　
　

Bluetooth function
Bluetooth wireless technology
A short-range wireless communications standard for digital devices. Information is exchanged between devices
several meters to several tens of meters apart using radio waves. It uses radio waves on the 2.4 GHz band which
does not require applications for licenses or usage registration for applications conducting wireless exchange
of digital information at relatively low speeds, such as computer mouses and keyboards, mobile phones, smartphones, text and audio information for PDAs, etc.

Pairing
“Pairing” must be done before you start playback of Bluetooth wireless technology content using the Bluetooth
ADAPTER. Make sure to perform pairing the first time you operate the system or any time pairing data is cleared.
The pairing step is necessary to register the Bluetooth wireless technology device to enable Bluetooth communications. For more details, see also the operating instructions of your Bluetooth wireless technology device.
!	 Pairing is required when you first use the Bluetooth wireless technology device and Bluetooth ADAPTER.
!	 To enable Bluetooth communication, pairing should be done with both your system and Bluetooth wireless
technology device.

Receiver function
Operation Mode
This receiver is equipped with a great number of functions and settings. The Operation Mode feature is provided
for users who find it difficult to master all these functions and settings.

106

14

Additional information

Slideshow

Features index

See Playing back photo files stored on a USB memory device on page 44.

Bluetooth ADAPTER

Operation Mode
See Operation Mode Setup on page 40.

See Bluetooth ADAPTER for Wireless Enjoyment of Music on page 46.

AVNavigator

ARC (Audio Return Channel)

See About using AVNavigator (included CD-ROM) on page 9.

See HDMI Setup on page 59.

Full Auto MCACC

SACD Gain

See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 37.

See Setting the Audio options on page 62.

Automatic MCACC (Expert)

Auto delay

See Automatic MCACC (Expert) on page 76.

See Setting the Audio options on page 62.

Manual MCACC setup

Height Gain (Dolby Pro Logic llz Height option)

See Manual MCACC setup on page 78.

See Setting the Audio options on page 62.

PQLS

Virtual Surround Back

See Setting the PQLS function on page 60.

See Setting the Audio options on page 62.

Phase Control

Virtual Height

See Better sound using Phase Control on page 51.

See Setting the Audio options on page 62.

Standing Wave

Virtual Wide

See Setting the Audio options on page 62.

See Setting the Audio options on page 62.

Phase Control Plus

Virtual Depth

See Setting the Audio options on page 62.

See Setting the Audio options on page 62.

Auto Sound Retriever

Digital Video Converter

See Setting the Audio options on page 62.

See Setting the Video options on page 64.

ALC (Auto Level Control)

Pure Cinema

See Auto playback on page 49.

See Setting the Video options on page 64.

Front Stage Surround Advance

Progressive Motion

See Enjoying various types of playback using the listening modes on page 49.

See Setting the Video options on page 64.

Sound Retriever Air

Advanced Video Adjust

See Enjoying various types of playback using the listening modes on page 49.

See Setting the Video options on page 64.

Dialog Enhancement

Auto Power Down
See The Other Setup menu on page 87.

See Setting the Audio options on page 62.

Internet radio
See Listening to Internet radio stations on page 54.

vTuner
See Listening to Internet radio stations on page 54.

DLNA
See About network playback on page 55.

AirPlay
See Using AirPlay on iPod touch, iPhone, iPad, and iTunes on page 53.

Wireless LAN
See Connecting to a wireless LAN on page 34.

Playback High Resolution audio file
See About playable file formats on page 57.
See Playing a USB device on page 44.

107

　
　
　
　

14

Additional information

Integrated Control Section

Specifications
Amplifier section
Continuous average power output of 120 watts* per channel, min., at 8 ohms, 1 kHz with no more than
0.08 %** total harmonic distortion.
Multi channel simultaneous power output (1 kHz, 1 %, 8 W)
7 ch total..............................................................................................................................................................600 W
Continuous Power Output (1 kHz, 8 W, 0.08 %)
Front.................................................................................................................................................... 120 W + 120 W
Center..................................................................................................................................................................120 W
Surround............................................................................................................................................. 120 W + 120 W
Surround back.................................................................................................................................... 120 W + 120 W
Continuous Power Output (1 kHz, 4 W, 1.0 %)
Front.................................................................................................................................................... 190 W + 190 W
Center..................................................................................................................................................................190 W
Surround............................................................................................................................................. 190 W + 190 W
Surround back.................................................................................................................................... 190 W + 190 W
Total harmonic distortion......................................................................................... 0.04 % (1 kHz, 110 W + 110 W, 8 W)
Guaranteed speaker impedance...................................................................................................................... 4 W to 16 W
* Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Output Claims for
Amplifiers
** Measured by Audio Spectrum Analyzer

Audio Section
Input (Sensitivity/Impedance)
LINE........................................................................................................................................................370 mV/47 kW
Output (Level/Impedance)
REC........................................................................................................................................................370 mV/2.2 kW
Signal-to-Noise Ratio (IHF, short circuited, A network)
LINE................................................................................................................................................................... 101 dB

Tuner Section
Frequency Range (FM).....................................................................................................................87.5 MHz to 108 MHz
Antenna Input (FM)................................................................................................................................. 75 W unbalanced
Frequency Range (AM).......................................................................................................................530 kHz to 1700 kHz
Antenna (AM)............................................................................................................................. Loop antenna (balanced)

Video Section
Signal level
Composite Video..................................................................................................................................... 1 Vp-p (75 W)
Component Video..................................................................................... Y: 1.0 Vp-p (75 W), PB/PR: 0.7 Vp-p (75 W)
Corresponding maximum resolution
Component Video.................................................................................................. 1080p (1125p) (Video convert off)

Digital In/Out Section
HDMI terminal.......................................................................................................................................... 19-pin (Not DVI)
HDMI output type............................................................................................................................................... 5 V, 55 mA
USB terminal........................................................................................................ USB2.0 High Speed (Type A) 5 V, 2.1 A
iPod terminal........................................................................................................................ USB, and Video (Composite)
ADAPTER PORT terminal................................................................................................................................ 5 V, 100 mA
WIRELESS LAN ADAPTER terminal............................................................................................................... 5 V, 600 mA

108

Control (IR) terminal.....................................................................................................................ø 3.5 Mini-jack (MONO)
IR signal..............................................................................................................................High Active (High Level: 2.0 V)
RS-232C cable type.........................................................................................................9-pin, cross type, female-female
EXTENSION terminal....................................................................................................................................... 5 V, 150 mA

Network Section
LAN terminal................................................................................................................................10 BASE-T/100 BASE-TX

Miscellaneous
Power requirements..................................................................................................................................AC 120 V, 60 Hz
Power consumption...................................................................................................................................................290 W
In standby...........................................................................................................0.1 W (HDMI Setup – Control : OFF)
0.3 W (HDMI Setup – Control : ON)
Dimensions....................................................................................................... 435 mm (W) x 185 mm (H) x 441 mm (D)
(17 1/8 in. (W) x 7 1/4 in. (H) x 17 3/8 in. (D))
Weight (without package).........................................................................................................................14.4 kg (31.7 lb)

Number of Furnished Parts
MCACC Setup microphone............................................................................................................................................... 1
Remote control unit........................................................................................................................................................... 1
AAA size IEC R03 dry cell batteries................................................................................................................................... 2
iPod cable........................................................................................................................................................................... 1
AM loop antenna................................................................................................................................................................ 1
FM wire antenna................................................................................................................................................................ 1
Power cord
CD-ROM (AVNavigator)
Quick start guide
Safety Brochure
Warranty sheet

Note
!	 Specifications and the design are subject to possible modifications without notice, due to improvements.
!	 This product includes FontAvenue® fonts licensed by NEC Corporation. FontAvenue is a registered trademark of
NEC Corporation.

　
　
　
　

14

Additional information

Penney 0100, 0102
Philco 0003, 0004, 0005,
0006, 0007, 0100, 0101
Philips 0003, 0004, 0007,
0019, 0020, 0101
Philips Magnavox 0019
Pilot 0004, 0100
Polaroid 0057, 0106
Portland 0004, 0005, 0006
Prima 0065
Princeton 0097
Prism 0010
Proscan 0000
Proton 0004, 0006, 0007
Protron 0055
Proview 0068
Pulsar 0004, 0011, 0099
Quasar 0003, 0010, 0105
Radio Shack 0100, 0104
Radio Shack/Realistic 0000,
0004, 0006, 0007, 0008
RCA 0000, 0003, 0004, 0005,
0006, 0013, 0024, 0035
Realistic 0100, 0104
Runco 0011, 0099, 0100
Sampo 0004, 0006, 0100,
0107
Samsung 0004, 0005, 0006,
0007, 0022, 0032, 0076, 0077,
0083, 0100, 0110
Sansui 0025
Sanyo 0004, 0050
Sceptre 0072
Scotch 0006
Scott 0004, 0006, 0007, 0008,
0009, 0090, 0104
Sears 0000, 0004, 0006,
0009, 0101, 0102, 0103
Sharp 0004, 0006, 0007,
0014, 0033
Sheng Chia 0014
Shogun 0004
Signature 0001
Sony 0002, 0018, 0029, 0030,
0031, 0034
Soundesign 0004, 0006,
0008, 0009, 0104
Squareview 0103
SSS 0004, 0008, 0104
Starlite 0008, 0104
Superscan 0014
Supre-Macy 0012
Supreme 0002
SVA 0088

Preset code list
You should have no problem controlling a component if you find the manufacturer in this list, but please note that
there are cases where codes for the manufacturer in the list will not work for the model that you are using. There
are also cases where only certain functions may be controllable after assigning the proper preset code.

Important
!	 We do not guarantee the operations of all the manufacturers and devices listed. Operation may not be possible
even if a preset code is entered.
	 If you can’t find a preset code that matches the component you want to control, you can still teach the remote
individual commands from another remote control (see Programming signals from other remote controls on
page 71).

TV
Pioneer 0004, 0006, 0113,
0233, 0252, 0275, 0291, 0305
Admiral 0001, 0014
Adventura 0012
Aiwa 0002
Akai 0002, 0100
Albatron 0097
Alleron 0009
America Action 0104
Amtron 0008
Anam 0104
Anam National 0003, 0008
AOC 0004, 0005, 0006, 0100
Apex 0021, 0102, 0106
Audiovox 0008, 0104
Aventura 0103
Axion 0094
Bang & Olufsen 0111
Belcor 0004
Bell & Howell 0001
Benq 0064
Bradford 0008, 0104
Brillian 0109
Brockwood 0004
Broksonic 0104
Candle 0004, 0006, 0012,
0100
Carnivale 0100
Carver 0101
CCE 0110
Celebrity 0002
Celera 0106
Changhong 0106
Citizen 0004, 0006, 0008,
0100
Clarion 0104
Coby 0056
Colortyme 0004, 0006

Concerto 0004, 0006
Contec 0104
Contec/Cony 0007, 0008
Craig 0008, 0104
Crosley 0081, 0101
Crown 0008, 0104
CTX 0063
Curtis Mathes 0000, 0004,
0006, 0014, 0100, 0101
CXC 0008, 0104
Cytron 0093
Daewoo 0004, 0005, 0006,
0023
Daytron 0004, 0006
Dell 0073
DiamondVision 0096
Dimensia 0000
Disney 0046
Dumont 0004, 0011, 0099
Durabrand 0041, 0103, 0104
Dwin 0014
Electroband 0002
Electrograph 0107
Electrohome 0002, 0003,
0004, 0006
Element 0082
Emerson 0004, 0006, 0007,
0008, 0009, 0023, 0103, 0104
Emprex 0092
Envision 0004, 0006, 0100
Epson 0061
ESA 0103
Fujitsu 0009
Funai 0008, 0009, 0103, 0104
Futuretech 0008, 0104
Gateway 0067, 0107, 0108
GE 0000, 0003, 0004, 0006,
0010, 0016, 0039

GFM 0080, 0084
Gibralter 0004, 0011, 0099,
0100
Goldstar 0004, 0005, 0006,
0007, 0100
Gradiente 0066
Grunpy 0008, 0009, 0104
Haier 0112
Hallmark 0004, 0006
Harman/Kardon 0101
Harvard 0008, 0104
Havermy 0014
Hewlett Packard 0053
Hisense 0069
Hitachi 0004, 0006, 0007
Hyundai 0098
Ilo 0089, 0091
IMA 0008
Infinity 0101
InFocus 0074
Initial 0091
Insignia 0085, 0086
Inteq 0099
Janeil 0012
JBL 0101
JC Penney 0000, 0004, 0005,
0006, 0010
JCB 0002
Jensen 0004, 0006
JVC 0007, 0010, 0044
Kawasho 0002, 0004, 0006
KEC 0104
Kenwood 0004, 0006, 0100
KLH 0106
Kloss Novabeam 0008, 0012
KTV 0008, 0100, 0104, 0110
LG 0005, 0052, 0078, 0097
Logik 0001

Luxman 0004, 0006
LXI 0000, 0006, 0101, 0102
Magnavox 0004, 0006,
0019, 0020, 0037, 0042, 0100,
0101
Majestic 0001
Marantz 0004, 0006, 0062,
0100, 0101
Maxent 0087, 0107
Megapower 0097
Megatron 0006
Memorex 0001, 0005, 0006,
0041
MGA 0004, 0005, 0006, 0100
Midland 0010, 0011, 0099
Mintek 0091
Mitsubishi 0004, 0005, 0006,
0014, 0045
Monivision 0097
Montgomery Ward 0001
Motorola 0003, 0014
MTC 0004, 0005, 0006, 0100
Multitech 0008, 0104, 0110
NAD 0006, 0102
NEC 0003, 0004, 0005, 0006,
0100
Net-TV 0107
Nikko 0006, 0100
Norcent 0060
Olevia 0048, 0054, 0059
Onwa 0008, 0104
Oppo 0095
Optimus 0105
Optoma 0075
Optonica 0014
Orion 0025
Panasonic 0003, 0010, 0017,
0027, 0105, 0114

109

Sylvania 0004, 0006, 0049,
0079, 0080, 0100, 0101, 0103
Symphonic 0008, 0041,
0103, 0104
Syntax 0054
Syntax-Brillian 0054
Tandy 0014
Tatung 0003, 0108
Technics 0010, 0105
Techwood 0004, 0006, 0010
Teknika 0001, 0004, 0005,
0006, 0007, 0008, 0009, 0101,
0104
TMK 0004, 0006
TNCi 0099
Toshiba 0026, 0028, 0036,
0038, 0040, 0043, 0102
Vector Research 0100
Vidikron 0101
Vidtech 0004, 0005, 0006
Viewsonic 0058, 0107
Viking 0012
Viore 0089
Vizio 0004, 0070, 0071, 0108
Wards 0000, 0001, 0004,
0005, 0006, 0009, 0100, 0101
Waycon 0102
Westinghouse 0047, 0051
White Westinghouse 0023
Yamaha 0004, 0005, 0006,
0100
Zenith 0001, 0004, 0011,
0015, 0099

　
　
　
　

14

Additional information

DVD

VCR

If operations are not possible using the preset codes below, you may be able to conduct operations with the preset
codes for the BD, DVR (BDR, HDR).

Pioneer 1035, 1108
ABS 1017
Adventura 1005
Aiwa 1005
Alienware 1017
American High 1004
Asha 1002
Audio Dynamics 1000
Audiovox 1003
Bang & Olufsen 1032
Beaumark 1002
Bell & Howell 1001
Calix 1003
Candle 1002, 1003
Canon 1004
Citizen 1002, 1003
Colortyme 1000
Craig 1002, 1003
Curtis Mathes 1000, 1002,
1004
Cybernex 1002
CyberPower 1017
Daewoo 1005
DBX 1000
Dell 1017
DIRECTV 1016, 1020, 1022,
1023, 1024, 1027, 1030, 1031
Dish Network 1029
Dishpro 1029
Durabrand 1018
Dynatech 1005
Echostar 1029
Electrohome 1003
Electrophonic 1003
Emerson 1003, 1004, 1005
Expressvu 1029
Fisher 1001
Fuji 1004
Funai 1005

Pioneer 2014, 2197, 2256
Accurian 2092
Advent 2072
Aiwa 2012
Akai 2066
Alco 2070
Allegro 2087
Amphion MediaWorks
2037
AMW 2037
Apex 2002, 2018, 2079, 2080
Apple 2058
Arrgo 2088
Aspire 2073
Astar 2052
Audiovox 2070
Axion 2040
Bang & Olufsen 2081
Blaupunkt 2080
Blue Parade 2078
Boston 2059
Broksonic 2066
California Audio Labs 2068
CambridgeSoundWorks
2065
CineVision 2087
Coby 2029
Curtis Mathes 2089
CyberHome 2000, 2088
Cytron 2039

Daewoo 2021, 2087
Denon 2026, 2068
Desay 2055
DiamondVision 2042
Disney 2022
Durabrand 2090
Emerson 2067, 2082, 2091
Enterprise 2082
ESA 2053, 2091
Fisher 2083
Funai 2091
GE 2016, 2077, 2080
GFM 2043
Go Video 2087
Gradiente 2068
Greenhill 2080
Haier 2094
Harman/Kardon 2030, 2084
Hitachi 2011
Hiteker 2079
iLive 2062
Ilo 2038
Initial 2038, 2080
Insignia 2036, 2064, 2091
Integra 2078
iSymphony 2060
JBL 2084
JVC 2013
Kawasaki 2070
Kenwood 2028, 2068

KLH 2070, 2080
Koss 2024, 2069, 2075
Landel 2093
Lasonic 2085
Lenoxx 2074, 2090
LG 2019, 2051, 2061, 2082,
2087
Liquid Video 2075
Liteon 2025, 2092
Magnavox 2067, 2076, 2091
Memorex 2066
Microsoft 2077
Mintek 2038, 2080, 2086
Mitsubishi 2020
Nesa 2080
Next Base 2093
Nexxtech 2056
Onkyo 2076
Oppo 2041, 2057
Oritron 2069, 2075
Panasonic 2005, 2007, 2017,
2032, 2033, 2050, 2068, 2076
Philips 2045, 2076
Proceed 2079
Proscan 2077
Qwestar 2069
RCA 2008, 2016, 2070, 2077,
2078, 2080
Regent 2074
Rio 2087

Rowa 2071
Samsung 2009, 2011, 2015,
2031, 2044, 2068
Sansui 2066
Sanyo 2066, 2083
Sharp 2035
Sherwood 2063
Shinsonic 2086
Sonic Blue 2087
Sony 2003, 2004, 2010, 2012,
2027, 2046, 2047, 2048
Sungale 2054
Superscan 2067
Sylvania 2023, 2067, 2091
Symphonic 2023
Teac 2070
Technics 2068
Theta Digital 2078
Toshiba 2001, 2006, 2049,
2066, 2076
Trutech 2000
Urban Concepts 2076
US Logic 2086
Venturer 2070
Xbox 2077
Yamaha 2005, 2068
Zenith 2019, 2076, 2082,
2087

BD
If operations are not possible using the preset codes below, you may be able to conduct operations with the preset
codes for the DVD, DVR (BDR, HDR).
Pioneer 2034, 2192, 2255,
2258, 2259, 2260, 2281
Denon 2310, 2311, 2312
Hitachi 2307, 2308, 2309

JVC 2290, 2291, 2293, 2294,
2295, 2296
LG 2286, 2287
Marantz 2302, 2303
Mitsubishi 2300, 2301

Onkyo 2289
Panasonic 2277, 2278, 2279
Philips 2280
Samsung 2282
Sharp 2304, 2305, 2306

Sony 2283, 2284, 2285, 2292
Toshiba 2288, 2262
Yamaha 2297, 2298, 2299

Garrard 1005
Gateway 1017
GE 1002, 1004
GOI 1029
Goldstar 1000, 1003
Gradiente 1005
Harley Davidson 1005
Harman/Kardon 1000
Headquarter 1001
Hewlett Packard 1017
HNS 1016
Howard Computers 1017
HP 1017
HTS 1029
Hughes Network Systems
1016, 1020, 1022, 1023, 1024
Humax 1016, 1020
Hush 1017
iBUYPOWER 1017
Instant Replay 1004
JC Penney 1000, 1001, 1002,
1003, 1004
JCL 1004
JVC 1000, 1001, 1020, 1029
Kenwood 1000, 1001
Kodak 1003, 1004
LG 1003
Linksys 1017
Lloyd’s 1005
LXI 1003
Magnavox 1004, 1018
Magnin 1003
Marantz 1000, 1001, 1004
Marta 1003
Media Center PC 1017
MEI 1004
Memorex 1001, 1002, 1003,
1004, 1005, 1018, 1019
MGN Technology 1002

Microsoft 1017
Mind 1017
Mitsubishi 1010
Motorola 1004
MTC 1002
Multitech 1002, 1005
NEC 1000, 1001
Nikko 1003
Niveus Media 1017
Noblex 1002
Northgate 1017
Olympus 1004
Optimus 1003
Orion 1014, 1019
Panasonic 1004, 1008
Philco 1004
Philips 1004, 1011, 1016,
1020, 1022, 1023, 1024, 1025
Philips Magnavox 1011
Pilot 1003
Proscan 1030
Pulsar 1018
Quarter 1001
Quartz 1001
Quasar 1004
Radio Shack 1003
Radio Shack/Realistic 1001,
1002, 1003, 1004, 1005
Radix 1003
Randex 1003
RCA 1002, 1004, 1007, 1016,
1020, 1022, 1030, 1031
Realistic 1001, 1002, 1003,
1004, 1005
ReplayTV 1026
Ricavision 1017
Runco 1018
Samsung 1002, 1016, 1022,
1024

Sanky 1018
Sansui 1014, 1019
Sanyo 1001, 1002
Sears 1001, 1003, 1004
Sharp 1012
Shogun 1002
Singer 1004
Sonic Blue 1026
Sony 1006, 1009, 1017, 1021
Stack 1017
STS 1004
Sylvania 1004, 1005
Symphonic 1005
Systemax 1017
Tagar Systems 1017
Tandy 1001
Tashiko 1003
Teac 1005
Technics 1004
Teknika 1003, 1004, 1005
Tivo 1016, 1020, 1021, 1022,
1025
TMK 1002
Toshiba 1015, 1017, 1028
Totevision 1002, 1003
Touch 1017
UltimateTV 1031
Unitech 1002
Vector Research 1000
Video Concepts 1000
Videosonic 1002
Viewsonic 1017
Voodoo 1017
Wards 1002, 1003, 1004,
1005
XR-1000 1004, 1005,
Yamaha 1000, 1001
Zenith 1013, 1018
ZT Group 1017

Kenwood 5020, 5021, 5031
Luxman 5049
Marantz 5033
Onkyo 5017, 5018, 5030,
5050
Panasonic 5036
Philips 5022, 5032, 5044

RCA 5013, 5029
Roadstar 5052
Sharp 5051
Sony 5012, 5023, 5026, 5027,
5028, 5039
TEAC 5015, 5016, 5034, 5035,
5037

Technics 5041
Victor 5014
Yamaha 5024, 5025, 5038,
5046, 5047

CD
Pioneer 5000, 5011, 5070
AKAI 5043
Asuka 5045
Denon 5019
Fisher 5048
Goldstar 5040
Hitachi 5042

DVR (BDR, HDR)
If operations are not possible using the preset codes below, you may be able to conduct operations with the preset
codes for the DVD, BD.
Pioneer 2078, 2099, 2107,
2260, 2261, 2264, 2265, 2266, Sharp 2267, 2275
Toshiba 2274
2109, 2144, 2193, 2194, 2195, 2270
Sony 2268, 2271, 2272, 2273,
2196, 2257, 2258, 2259,
Panasonic 2263, 2269
2276

110

14

Additional information

Pace 6074, 6029, 6028,
6106, 6083
Panasonic 6112, 6083
Paragon 6112
Penney 6112
Philips 6012
Pulsar 6112
Quasar 6112

Satellite Set Top Box
Pioneer 6097, 6098, 6325,
6328, 6329
ADB 6035, 6001
Akai 6102
Alba 6005, 6011, 6013
Allsat 6102
Alltech 6011
Amstrad 6033, 6030, 6044
Anttron 6013
Asat 6102
Austar 6000, 6045
Bell ExpressVu 6002, 6003
British Sky Broadcasting
6030
Canal 6105
Chaparral 6034
CNS 6001
Coolsat 6021
Crossdigital 6043
Digenius 6104
Digiwave 6053
DirecTV 6070, 6110, 6111,
6062, 6063, 6113, 6008, 6038,
6054, 6069, 6060, 6059, 6043,
6018, 6114, 6115, 6116, 6093
Dish Network System
6002, 6089, 6003, 6004
Dishpro 6002, 6089, 6004
Echostar 6002, 6089, 6036,
6005, 6003, 6004

Expressvu 6002, 6004
Fortec Star 6123, 6023
Fresat 6014
Funai 6070
GE 6111
General Instrument 6032
GOI 6002, 6004
Grundig 6007, 6030
Hirschmann 6033
Hisense 6020
Hitachi 6038, 6049
Houston 6002
HTS 6002, 6004
Hughes Network Systems
6113, 6038, 6054, 6114, 6115,
6116
Hyundai 6016
iLo 6020
Innova 6059
Jerrold 6032
Kathrein 6096
Lava 6053
LG 6047, 6018
Marantz 6102
McIntosh 6032
Mitsubishi 6038
Motorola 6032, 6042
NEC 6050, 6131
Netsat 6059
Next Level 6032

nfusion 6015
Nokia 6025, 6026, 6118,
6119, 6121
Pace 6035, 6005, 6030, 6031
Panarex 6016
Panasonic 6008, 6009, 6030
Pansat 6016, 6022
Philips 6002, 6113, 6038,
6054, 6060, 6059, 6102, 6103,
6030, 6114
Primestar 6032
Proscan 6110, 6111
Proton 6020
RadioShack 6002, 6111,
6032
Radix 6036
RCA 6002, 6110, 6111, 6113,
6109, 6061, 6114
Saba 6014
Sagem 6041, 6120
Samsung 6070, 6113, 6091,
6043, 6017, 6114, 6093
Sanyo 6046
Sat Cruiser 6015
Schwaiger 6066
Siemens 6007, 6036
SKY 6042, 6059, 6030, 6031
SM Electronic 6011
Smart 6051
Sonicview 6055, 6107

Sony 6062, 6063, 6030
Star Choice 6032
Star Trak 6032
TechniSat 6033
Thomson 6110, 6111, 6014
Tivo 6113, 6114, 6115, 6116
Toshiba 6038, 6054, 6039
TPS 6041
Triasat 6033
Ultrasat 6021
US Digital 6020
USDTV 6020
ViewSat 6048
Voom 6032
Zehnder 6101
Zenith 6042, 6069, 6037

Dishpro 6002, 6089
Echostar 6002, 6089, 6003
Expressvu 6002
Hughes Network Systems
6113, 6114, 6115, 6116
JVC 6003

Motorola 6032
Philips 6113, 6114
Proscan 6110
Samsung 6114
Sonicview 6055, 6107
Sony 6062

Pioneer 6029, 6325, 6328,
6329
Amino 6078
Bright House 6074, 6029
Cable One 6074, 6029
Cablevision 6074, 6029
Charter 6074, 6029, 6058
Cisco 6029, 6083

Comcast 6074, 6029, 6083,
6076
Cox 6074, 6029
Digeo 6081, 6058
Homecast 6024
Insight 6074, 6029
Knology 6029
Mediacom 6074, 6029

CD-R
Pioneer 5001, 5053, 5071
Philips 5054
Yamaha 5055

Tuner
Pioneer 5060

Laser Disc Player
Pioneer 5002, 5003

Cassete Deck
Pioneer 5058, 5059

Star Choice 6032
Tivo 6113, 6114, 6115, 6116

Digital Tape
Pioneer 5057

MD
Pioneer 5056

Cable Set Top Box
Pioneer 0297, 6028, 6029,
6095, 6099, 6325, 6328, 6329
ABC 6122
Accuphase 6122
Amino 6077, 6078
Auna 6082
BCC 6072
Bell & Howell 6122
Bright House 6074, 6029

Cable One 6074, 6029
Cablevision 6074, 6029
Charter 6074, 6029, 6058
Cisco 6029, 6028, 6083
Comcast 6074, 6029, 1982
Cox 6074, 6029
Digeo 6029, 6058
Director 6073
Emerson 6122

Fosgate 6072
General Instrument 6073,
6072, 6122
Homecast 6024
i3 Micro 6077
Insight 6074, 6073, 6029
Jebsee 6122
Jerrold 6073, 6072, 6122
Knology 6029

Starcom 6122
Stargate 6122
Suddenlink 6074, 6029
Supercable 6072
Time Warner 6074, 6029,
6058
Tivo 6076
Toshiba 6112

United Cable 6072, 6122
US Electronics 6072
Videoway 6112
Zenith 6112

Cable Set Top Box (Cable/PVR Combination)

Satellite Set Top Box (SAT/PVR Combination)
Bell ExpressVu 6002, 6003
DirecTV 6070, 6110, 6062,
6113, 6060, 6059, 6114, 6115,
6116
Dish Network System
6002, 6089

Regal 6072
Rogers 6029
Runco 6112
Samsung 6095
Scientific Atlanta 6029,
6028, 6027, 6112
Sejin 6077
Shaw 6074

Network Audio Player

Macab 6040
Mediacom 6074, 6029
Memorex 6112
Motorola 6074, 6073, 6072,
6029, 6122, 6094
MTS 6094
Myrio 6077, 6078
Noos 6040

Pioneer 5063

Game
X-Box 2313

AV Receiver
Pioneer 5096 (ID 1), 5097 (ID 2), 5098 (ID 3), 5099 (ID 4),

111

Motorola 6074, 6081
Myrio 6078
Pace 6029
Panasonic 6083
Rogers 6029
Scientific Atlanta 6029
Shaw 6074
Suddenlink 6074, 6029

Supercable 6072
Time Warner 6074, 6029,
6058
Tivo 6076

To register your product, find the nearest authorized service location, to
purchase replacement parts, operating instructions, or accessories,
please go to one of following URLs :
Pour enregistrer votre produit, trouver le service après-vente agréé le plus
proche et pour acheter des pièces de rechange, des modes d’emploi ou
des accessoires, reportez-vous aux URL suivantes :

In the USA/Aux Etats-Unis
http://www.pioneerelectronics.com

In Canada/Aux Canada
http://www.pioneerelectronics.ca
S018_B1_EnFr

PIONEER CORPORATION

1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

PIONEER ELECTRONICS (USA) INC.

P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404

PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.

Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B3_En

© 2012 PIONEER CORPORATION.
All rights reserved.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms, Extract, Print high-res
Page Mode                       : UseThumbs
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Create Date                     : 2012:02:23 13:51:13+09:00
Metadata Date                   : 2012:06:04 10:08:44+09:00
Modify Date                     : 2012:06:04 10:08:44+09:00
Creator Tool                    : Adobe InDesign CS5_J (7.0.4)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 4628 bytes, use -b option to extract), (Binary data 11181 bytes, use -b option to extract)
Instance ID                     : uuid:110949c0-3173-46d4-a6cc-2ed0cbbd9cc3
Document ID                     : xmp.did:500B86CCCF5DE1119D9EB07065E3A2A3
Original Document ID            : xmp.did:BD7C5823AFD2DF1185BFE72C625F81A3
Rendition Class                 : proof:pdf
History Action                  : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:BD7C5823AFD2DF1185BFE72C625F81A3, xmp.iid:BE7C5823AFD2DF1185BFE72C625F81A3, xmp.iid:BF7C5823AFD2DF1185BFE72C625F81A3, xmp.iid:C07C5823AFD2DF1185BFE72C625F81A3, xmp.iid:C17C5823AFD2DF1185BFE72C625F81A3, xmp.iid:C27C5823AFD2DF1185BFE72C625F81A3, xmp.iid:80D25B57DED4DF118EE3809702E6E73B, xmp.iid:D68BFAE4E1D4DF1184DB93F360701A6D, xmp.iid:6667E981EED4DF119477AE0AFF17CF30, xmp.iid:6767E981EED4DF119477AE0AFF17CF30, xmp.iid:6867E981EED4DF119477AE0AFF17CF30, xmp.iid:6967E981EED4DF119477AE0AFF17CF30, xmp.iid:6A67E981EED4DF119477AE0AFF17CF30, xmp.iid:6B67E981EED4DF119477AE0AFF17CF30, xmp.iid:6C67E981EED4DF119477AE0AFF17CF30, xmp.iid:6D67E981EED4DF119477AE0AFF17CF30, xmp.iid:6E67E981EED4DF119477AE0AFF17CF30, xmp.iid:7F509948F7D4DF119477AE0AFF17CF30, xmp.iid:80509948F7D4DF119477AE0AFF17CF30, xmp.iid:81509948F7D4DF119477AE0AFF17CF30, xmp.iid:82509948F7D4DF119477AE0AFF17CF30, xmp.iid:DF1DBB9703D5DF119477AE0AFF17CF30, xmp.iid:E01DBB9703D5DF119477AE0AFF17CF30, xmp.iid:E11DBB9703D5DF119477AE0AFF17CF30, xmp.iid:E31DBB9703D5DF119477AE0AFF17CF30, xmp.iid:E41DBB9703D5DF119477AE0AFF17CF30, xmp.iid:E51DBB9703D5DF119477AE0AFF17CF30, xmp.iid:E61DBB9703D5DF119477AE0AFF17CF30, xmp.iid:E71DBB9703D5DF119477AE0AFF17CF30, xmp.iid:90160B1294D6DF119B68B9CA869E44B8, xmp.iid:265F67786CD7DF1180ABEB0C5B508451, xmp.iid:275F67786CD7DF1180ABEB0C5B508451, xmp.iid:285F67786CD7DF1180ABEB0C5B508451, xmp.iid:FA0FD85F26D8DF11AEA0D14A8F41919A, xmp.iid:FC0FD85F26D8DF11AEA0D14A8F41919A, xmp.iid:FD0FD85F26D8DF11AEA0D14A8F41919A, xmp.iid:FE0FD85F26D8DF11AEA0D14A8F41919A, xmp.iid:FF0FD85F26D8DF11AEA0D14A8F41919A, xmp.iid:0010D85F26D8DF11AEA0D14A8F41919A, xmp.iid:0110D85F26D8DF11AEA0D14A8F41919A, xmp.iid:C1551CBD4FD8DF11AEA0D14A8F41919A, xmp.iid:C2551CBD4FD8DF11AEA0D14A8F41919A, xmp.iid:C3551CBD4FD8DF11AEA0D14A8F41919A, xmp.iid:C4551CBD4FD8DF11AEA0D14A8F41919A, xmp.iid:B065F5458FD9DF118E15F9A692C32F03, xmp.iid:B165F5458FD9DF118E15F9A692C32F03, xmp.iid:B265F5458FD9DF118E15F9A692C32F03, xmp.iid:B365F5458FD9DF118E15F9A692C32F03, xmp.iid:B465F5458FD9DF118E15F9A692C32F03, xmp.iid:B565F5458FD9DF118E15F9A692C32F03, xmp.iid:B665F5458FD9DF118E15F9A692C32F03, xmp.iid:B765F5458FD9DF118E15F9A692C32F03, xmp.iid:B865F5458FD9DF118E15F9A692C32F03, xmp.iid:B965F5458FD9DF118E15F9A692C32F03, xmp.iid:08A77BFA9DDADF1185E5BCAD3A02C8DD, xmp.iid:09A77BFA9DDADF1185E5BCAD3A02C8DD, xmp.iid:0AA77BFA9DDADF1185E5BCAD3A02C8DD, xmp.iid:0BA77BFA9DDADF1185E5BCAD3A02C8DD, xmp.iid:0CA77BFA9DDADF1185E5BCAD3A02C8DD, xmp.iid:1E43A314EADBDF11A0F6D0EC920EFD89, xmp.iid:1F43A314EADBDF11A0F6D0EC920EFD89, xmp.iid:2043A314EADBDF11A0F6D0EC920EFD89, xmp.iid:37186A90F1DBDF11A0F6D0EC920EFD89, xmp.iid:38186A90F1DBDF11A0F6D0EC920EFD89, xmp.iid:B0C43C0045DFDF11BED7D38683B319C5, xmp.iid:B1C43C0045DFDF11BED7D38683B319C5, xmp.iid:B2C43C0045DFDF11BED7D38683B319C5, xmp.iid:B3C43C0045DFDF11BED7D38683B319C5, xmp.iid:B4C43C0045DFDF11BED7D38683B319C5, xmp.iid:B5C43C0045DFDF11BED7D38683B319C5, xmp.iid:B6C43C0045DFDF11BED7D38683B319C5, xmp.iid:B7C43C0045DFDF11BED7D38683B319C5, xmp.iid:B8C43C0045DFDF11BED7D38683B319C5, xmp.iid:B9C43C0045DFDF11BED7D38683B319C5, xmp.iid:870060DD53DFDF11BED7D38683B319C5, xmp.iid:880060DD53DFDF11BED7D38683B319C5, xmp.iid:F343AB9156DFDF11AF17EE27679E0F26, xmp.iid:F443AB9156DFDF11AF17EE27679E0F26, xmp.iid:F543AB9156DFDF11AF17EE27679E0F26, xmp.iid:F643AB9156DFDF11AF17EE27679E0F26, xmp.iid:F743AB9156DFDF11AF17EE27679E0F26, xmp.iid:F843AB9156DFDF11AF17EE27679E0F26, xmp.iid:F943AB9156DFDF11AF17EE27679E0F26, xmp.iid:FA43AB9156DFDF11AF17EE27679E0F26, xmp.iid:FB43AB9156DFDF11AF17EE27679E0F26, xmp.iid:FC43AB9156DFDF11AF17EE27679E0F26, xmp.iid:874F22F764DFDF11AF17EE27679E0F26, xmp.iid:884F22F764DFDF11AF17EE27679E0F26, xmp.iid:894F22F764DFDF11AF17EE27679E0F26, xmp.iid:8A4F22F764DFDF11AF17EE27679E0F26, xmp.iid:8B4F22F764DFDF11AF17EE27679E0F26, xmp.iid:8C4F22F764DFDF11AF17EE27679E0F26, xmp.iid:8D4F22F764DFDF11AF17EE27679E0F26, xmp.iid:8E4F22F764DFDF11AF17EE27679E0F26, xmp.iid:8F4F22F764DFDF11AF17EE27679E0F26, xmp.iid:C7804F26CBDFDF11A6D9EB45E29DAC08, xmp.iid:C8804F26CBDFDF11A6D9EB45E29DAC08, xmp.iid:C9804F26CBDFDF11A6D9EB45E29DAC08, xmp.iid:CA804F26CBDFDF11A6D9EB45E29DAC08, xmp.iid:CB804F26CBDFDF11A6D9EB45E29DAC08, xmp.iid:CC804F26CBDFDF11A6D9EB45E29DAC08, xmp.iid:CD804F26CBDFDF11A6D9EB45E29DAC08, xmp.iid:CE804F26CBDFDF11A6D9EB45E29DAC08, xmp.iid:CF804F26CBDFDF11A6D9EB45E29DAC08, xmp.iid:B7D75AE801E0DF11A6D9EB45E29DAC08, xmp.iid:B8D75AE801E0DF11A6D9EB45E29DAC08, xmp.iid:B9D75AE801E0DF11A6D9EB45E29DAC08, xmp.iid:BAD75AE801E0DF11A6D9EB45E29DAC08, xmp.iid:63B73C88A7E0DF11B3C4858E17D37DEF, xmp.iid:64B73C88A7E0DF11B3C4858E17D37DEF, xmp.iid:65B73C88A7E0DF11B3C4858E17D37DEF, xmp.iid:66B73C88A7E0DF11B3C4858E17D37DEF, xmp.iid:FC5A6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:FD5A6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:FE5A6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:FF5A6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:005B6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:015B6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:025B6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:035B6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:045B6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:055B6C50B8E0DF11B58B83C56CDA20CC, xmp.iid:E506AEB1DAE0DF11B58B83C56CDA20CC, xmp.iid:E606AEB1DAE0DF11B58B83C56CDA20CC, xmp.iid:E706AEB1DAE0DF11B58B83C56CDA20CC, xmp.iid:E806AEB1DAE0DF11B58B83C56CDA20CC, xmp.iid:E906AEB1DAE0DF11B58B83C56CDA20CC, xmp.iid:EA06AEB1DAE0DF11B58B83C56CDA20CC, xmp.iid:EB06AEB1DAE0DF11B58B83C56CDA20CC, xmp.iid:EC06AEB1DAE0DF11B58B83C56CDA20CC, xmp.iid:6D7BA8AA6AE1DF1183F4B7CE091E9159, xmp.iid:6E7BA8AA6AE1DF1183F4B7CE091E9159, xmp.iid:6F7BA8AA6AE1DF1183F4B7CE091E9159, xmp.iid:F736CF3E7FE1DF11A5A8D52123199C2D, xmp.iid:F836CF3E7FE1DF11A5A8D52123199C2D, xmp.iid:F936CF3E7FE1DF11A5A8D52123199C2D, xmp.iid:FA36CF3E7FE1DF11A5A8D52123199C2D, xmp.iid:FB36CF3E7FE1DF11A5A8D52123199C2D, xmp.iid:571B6C6999E1DF1189E7A48C309892D5, xmp.iid:581B6C6999E1DF1189E7A48C309892D5, xmp.iid:591B6C6999E1DF1189E7A48C309892D5, xmp.iid:5A1B6C6999E1DF1189E7A48C309892D5, xmp.iid:5B1B6C6999E1DF1189E7A48C309892D5, xmp.iid:5C1B6C6999E1DF1189E7A48C309892D5, xmp.iid:5D1B6C6999E1DF1189E7A48C309892D5, xmp.iid:905EB9CAAAE1DF11B804A57D97F8F730, xmp.iid:EDAE583030E2DF118501FD8DDFD0F3C2, xmp.iid:EEAE583030E2DF118501FD8DDFD0F3C2, xmp.iid:D0DDE4F500E3DF118CD8C066DD3CB84A, xmp.iid:D1DDE4F500E3DF118CD8C066DD3CB84A, xmp.iid:D2DDE4F500E3DF118CD8C066DD3CB84A, xmp.iid:D3DDE4F500E3DF118CD8C066DD3CB84A, xmp.iid:D4DDE4F500E3DF118CD8C066DD3CB84A, xmp.iid:81A0E98795E4DF11AB55DEF4C0D16723, xmp.iid:82A0E98795E4DF11AB55DEF4C0D16723, xmp.iid:83A0E98795E4DF11AB55DEF4C0D16723, xmp.iid:84A0E98795E4DF11AB55DEF4C0D16723, xmp.iid:85A0E98795E4DF11AB55DEF4C0D16723, xmp.iid:86A0E98795E4DF11AB55DEF4C0D16723, xmp.iid:87A0E98795E4DF11AB55DEF4C0D16723, xmp.iid:88A0E98795E4DF11AB55DEF4C0D16723, xmp.iid:89A0E98795E4DF11AB55DEF4C0D16723, xmp.iid:8AA0E98795E4DF11AB55DEF4C0D16723, xmp.iid:6AF49B758BE5DF11B731D5C9AB127786, xmp.iid:6BF49B758BE5DF11B731D5C9AB127786, xmp.iid:6CF49B758BE5DF11B731D5C9AB127786, xmp.iid:6DF49B758BE5DF11B731D5C9AB127786, xmp.iid:6EF49B758BE5DF11B731D5C9AB127786, xmp.iid:26537129DFE7DF11AA68AFB8DBEA1FF8, xmp.iid:27537129DFE7DF11AA68AFB8DBEA1FF8, xmp.iid:28537129DFE7DF11AA68AFB8DBEA1FF8, xmp.iid:29537129DFE7DF11AA68AFB8DBEA1FF8, xmp.iid:2A537129DFE7DF11AA68AFB8DBEA1FF8, xmp.iid:2B537129DFE7DF11AA68AFB8DBEA1FF8, xmp.iid:2C537129DFE7DF11AA68AFB8DBEA1FF8, xmp.iid:46EAEA06C8EBDF118D03B6BB798DD5D3, xmp.iid:47EAEA06C8EBDF118D03B6BB798DD5D3, xmp.iid:48EAEA06C8EBDF118D03B6BB798DD5D3, xmp.iid:49EAEA06C8EBDF118D03B6BB798DD5D3, xmp.iid:4AEAEA06C8EBDF118D03B6BB798DD5D3, xmp.iid:25C95D4508EEDF11A75090A65772AC5D, xmp.iid:26C95D4508EEDF11A75090A65772AC5D, xmp.iid:27C95D4508EEDF11A75090A65772AC5D, xmp.iid:29C95D4508EEDF11A75090A65772AC5D, xmp.iid:73F0B7377EF3DF11AD289558223C1E16, xmp.iid:EBE173E5A4F3DF11AD289558223C1E16, xmp.iid:ECE173E5A4F3DF11AD289558223C1E16, xmp.iid:EDE173E5A4F3DF11AD289558223C1E16, xmp.iid:EEE173E5A4F3DF11AD289558223C1E16, xmp.iid:EFE173E5A4F3DF11AD289558223C1E16, xmp.iid:96AABDACCCF3DF11BE708E615171AC00, xmp.iid:35B33B7C07F6DF11AB4CA3A573C6476B, xmp.iid:36B33B7C07F6DF11AB4CA3A573C6476B, xmp.iid:37B33B7C07F6DF11AB4CA3A573C6476B, xmp.iid:38B33B7C07F6DF11AB4CA3A573C6476B, xmp.iid:3BB33B7C07F6DF11AB4CA3A573C6476B, xmp.iid:01A2A96F76F7DF1186B3E7C192F245D0, xmp.iid:B5C1AB3493F7DF11B51D87A8C28892B8, xmp.iid:B6C1AB3493F7DF11B51D87A8C28892B8, xmp.iid:912A50A13AF8DF118AE593D9C8D0B7BF, xmp.iid:922A50A13AF8DF118AE593D9C8D0B7BF, xmp.iid:932A50A13AF8DF118AE593D9C8D0B7BF, xmp.iid:942A50A13AF8DF118AE593D9C8D0B7BF, xmp.iid:952A50A13AF8DF118AE593D9C8D0B7BF, xmp.iid:972A50A13AF8DF118AE593D9C8D0B7BF, xmp.iid:982A50A13AF8DF118AE593D9C8D0B7BF, xmp.iid:992A50A13AF8DF118AE593D9C8D0B7BF, xmp.iid:9A2A50A13AF8DF118AE593D9C8D0B7BF, xmp.iid:8844983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:8944983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:8A44983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:8B44983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:8C44983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:8D44983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:8E44983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:8F44983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:9044983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:9144983E5AF8DF118AE593D9C8D0B7BF, xmp.iid:2588C7AE13F9DF11B198B407C250D1DF, xmp.iid:B86B22E363FCDF118CBD9FF558F6C96C, xmp.iid:B96B22E363FCDF118CBD9FF558F6C96C, xmp.iid:BA6B22E363FCDF118CBD9FF558F6C96C, xmp.iid:BB6B22E363FCDF118CBD9FF558F6C96C, xmp.iid:BC6B22E363FCDF118CBD9FF558F6C96C, xmp.iid:CFA21382E6FCDF1189ABB305DC55FD08, xmp.iid:D0A21382E6FCDF1189ABB305DC55FD08, xmp.iid:D1A21382E6FCDF1189ABB305DC55FD08, xmp.iid:D2A21382E6FCDF1189ABB305DC55FD08, xmp.iid:76D65BDE07FEDF118DB9B51D8BAF258A, xmp.iid:77D65BDE07FEDF118DB9B51D8BAF258A, xmp.iid:78D65BDE07FEDF118DB9B51D8BAF258A, xmp.iid:79D65BDE07FEDF118DB9B51D8BAF258A, xmp.iid:7AD65BDE07FEDF118DB9B51D8BAF258A, xmp.iid:7BD65BDE07FEDF118DB9B51D8BAF258A, xmp.iid:6FBEE9AE7DFEDF119C5486EC3966001A, xmp.iid:70BEE9AE7DFEDF119C5486EC3966001A, xmp.iid:71BEE9AE7DFEDF119C5486EC3966001A, xmp.iid:72BEE9AE7DFEDF119C5486EC3966001A, xmp.iid:73BEE9AE7DFEDF119C5486EC3966001A, xmp.iid:7DA615110301E011B2E2A5E844553EDA, xmp.iid:847218403903E0118EB6923FA0245970, xmp.iid:857218403903E0118EB6923FA0245970, xmp.iid:867218403903E0118EB6923FA0245970, xmp.iid:877218403903E0118EB6923FA0245970, xmp.iid:321A01FCFB03E011B68982AFFC596531, xmp.iid:331A01FCFB03E011B68982AFFC596531, xmp.iid:341A01FCFB03E011B68982AFFC596531, xmp.iid:351A01FCFB03E011B68982AFFC596531, xmp.iid:361A01FCFB03E011B68982AFFC596531, xmp.iid:371A01FCFB03E011B68982AFFC596531, xmp.iid:381A01FCFB03E011B68982AFFC596531, xmp.iid:391A01FCFB03E011B68982AFFC596531, xmp.iid:0EB723152608E01189EE8841C75CDB7E, xmp.iid:0FB723152608E01189EE8841C75CDB7E, xmp.iid:AF5AA2AFB61EE0119F468029ACC1BCF7, xmp.iid:B05AA2AFB61EE0119F468029ACC1BCF7, xmp.iid:B35AA2AFB61EE0119F468029ACC1BCF7, xmp.iid:580F12E37C1FE0119957FA2A4E0AB345, xmp.iid:20BF04EC2E24E011B72DC4EC2F4E7276, xmp.iid:21BF04EC2E24E011B72DC4EC2F4E7276, xmp.iid:23BF04EC2E24E011B72DC4EC2F4E7276, xmp.iid:24BF04EC2E24E011B72DC4EC2F4E7276, xmp.iid:25BF04EC2E24E011B72DC4EC2F4E7276, xmp.iid:26BF04EC2E24E011B72DC4EC2F4E7276, xmp.iid:27BF04EC2E24E011B72DC4EC2F4E7276, xmp.iid:9CC927E84F24E011B72DC4EC2F4E7276, xmp.iid:9DC927E84F24E011B72DC4EC2F4E7276, xmp.iid:9EC927E84F24E011B72DC4EC2F4E7276, xmp.iid:9FC927E84F24E011B72DC4EC2F4E7276, xmp.iid:A0C927E84F24E011B72DC4EC2F4E7276, xmp.iid:A1C927E84F24E011B72DC4EC2F4E7276, xmp.iid:A2C927E84F24E011B72DC4EC2F4E7276, xmp.iid:A3C927E84F24E011B72DC4EC2F4E7276, xmp.iid:A4C927E84F24E011B72DC4EC2F4E7276, xmp.iid:A6C927E84F24E011B72DC4EC2F4E7276, xmp.iid:0E6A68A82028E0119991EF7807710112, xmp.iid:0F6A68A82028E0119991EF7807710112, xmp.iid:106A68A82028E0119991EF7807710112, xmp.iid:126A68A82028E0119991EF7807710112, xmp.iid:1BB8D3477471E0118BB5C139B43BFB0D, xmp.iid:7E01DF248071E0118BB5C139B43BFB0D, xmp.iid:85D03CEE2396E0118BD0BC47D4B279BE, xmp.iid:86D03CEE2396E0118BD0BC47D4B279BE, xmp.iid:87D03CEE2396E0118BD0BC47D4B279BE, xmp.iid:8AD03CEE2396E0118BD0BC47D4B279BE, xmp.iid:8BD03CEE2396E0118BD0BC47D4B279BE, xmp.iid:8CD03CEE2396E0118BD0BC47D4B279BE, xmp.iid:42B2BF356E96E0119316A4E7D2B7C78C, xmp.iid:551DF83ACD97E011988DC480882787B2, xmp.iid:0EC26E35929CE011A009CCAC0691FF5A, xmp.iid:845051FC9B9CE0119903C9B4CB7A41A2, xmp.iid:875051FC9B9CE0119903C9B4CB7A41A2, xmp.iid:885051FC9B9CE0119903C9B4CB7A41A2, xmp.iid:895051FC9B9CE0119903C9B4CB7A41A2, xmp.iid:09ABA71CF99DE01181ADDFDBF00B07BB, xmp.iid:0AABA71CF99DE01181ADDFDBF00B07BB, xmp.iid:0BABA71CF99DE01181ADDFDBF00B07BB, xmp.iid:E355643C279EE011B320F4048AC33781, xmp.iid:E455643C279EE011B320F4048AC33781, xmp.iid:AA154985F0A1E0119BC284466FB97AE0, xmp.iid:0039D90382F0E0118A4FEF8414BC4E22, xmp.iid:0139D90382F0E0118A4FEF8414BC4E22, xmp.iid:0339D90382F0E0118A4FEF8414BC4E22, xmp.iid:0539D90382F0E0118A4FEF8414BC4E22, xmp.iid:0639D90382F0E0118A4FEF8414BC4E22, xmp.iid:00762ADF7FF5E011B099EB96CDAF7F81, xmp.iid:01762ADF7FF5E011B099EB96CDAF7F81, xmp.iid:02762ADF7FF5E011B099EB96CDAF7F81, xmp.iid:04762ADF7FF5E011B099EB96CDAF7F81, xmp.iid:82C5CF8E56F9E0119557A2DC9BF27A1E, xmp.iid:83C5CF8E56F9E0119557A2DC9BF27A1E, xmp.iid:84C5CF8E56F9E0119557A2DC9BF27A1E, xmp.iid:86C5CF8E56F9E0119557A2DC9BF27A1E, xmp.iid:ADC5D6450DFAE011B138BBA41BD7DCC5, xmp.iid:82EE9349C0FAE011B617A36978E74009, xmp.iid:83EE9349C0FAE011B617A36978E74009, xmp.iid:85EE9349C0FAE011B617A36978E74009, xmp.iid:86EE9349C0FAE011B617A36978E74009, xmp.iid:87EE9349C0FAE011B617A36978E74009, xmp.iid:88EE9349C0FAE011B617A36978E74009, xmp.iid:89EE9349C0FAE011B617A36978E74009, xmp.iid:8AEE9349C0FAE011B617A36978E74009, xmp.iid:8BEE9349C0FAE011B617A36978E74009, xmp.iid:FC45BEF3E7FAE011B617A36978E74009, xmp.iid:FD45BEF3E7FAE011B617A36978E74009, xmp.iid:FE45BEF3E7FAE011B617A36978E74009, xmp.iid:FF45BEF3E7FAE011B617A36978E74009, xmp.iid:0046BEF3E7FAE011B617A36978E74009, xmp.iid:0146BEF3E7FAE011B617A36978E74009, xmp.iid:89CE38FA7CFBE0119F6EC47661517117, xmp.iid:8ACE38FA7CFBE0119F6EC47661517117, xmp.iid:8BCE38FA7CFBE0119F6EC47661517117, xmp.iid:8CCE38FA7CFBE0119F6EC47661517117, xmp.iid:17F5609B6E04E11199CD8690557E8519, xmp.iid:DE15C0BDE404E111AE2DE40A07DC0ED6, xmp.iid:DF15C0BDE404E111AE2DE40A07DC0ED6, xmp.iid:19D50CFCBA05E111856FD804407EB05F, xmp.iid:72F4C576BB05E1118944C6C7C7D403AA, xmp.iid:73F4C576BB05E1118944C6C7C7D403AA, xmp.iid:3C746B718E06E111ADD588E4BEEB170F, xmp.iid:2608245F9F06E111ADD588E4BEEB170F, xmp.iid:FBED3A6B2209E1118FBDDBC27643B0A3, xmp.iid:F1AE4BA9A509E111A118F02C244CD66D, xmp.iid:64DC99F6D04BE1119163C50451ED6542, xmp.iid:88D9725BD14BE1119163C50451ED6542, xmp.iid:47B659E6B95DE111993BDC3615039B8D, xmp.iid:48B659E6B95DE111993BDC3615039B8D, xmp.iid:D97BA31CCE5DE1119D9EB07065E3A2A3, xmp.iid:500B86CCCF5DE1119D9EB07065E3A2A3, xmp.iid:70626786D85DE1119D9EB07065E3A2A3, xmp.iid:71626786D85DE1119D9EB07065E3A2A3, xmp.iid:79E744CCD95DE1119D9EB07065E3A2A3, xmp.iid:7AE744CCD95DE1119D9EB07065E3A2A3
History When                    : 2010:10:08 16:39:09+09:00, 2010:10:08 16:46:09+09:00, 2010:10:08 16:46:09+09:00, 2010:10:08 17:38:29+09:00, 2010:10:08 17:42:05+09:00, 2010:10:08 17:43:58+09:00, 2010:10:11 11:22:05+09:00, 2010:10:11 11:54:57+09:00, 2010:10:11 13:17:49+09:00, 2010:10:11 13:37:46+09:00, 2010:10:11 13:47:24+09:00, 2010:10:11 13:50:50+09:00, 2010:10:11 13:54:15+09:00, 2010:10:11 14:03:44+09:00, 2010:10:11 14:08:35+09:00, 2010:10:11 14:11:24+09:00, 2010:10:11 14:17:16+09:00, 2010:10:11 14:33:57+09:00, 2010:10:11 14:38:30+09:00, 2010:10:11 15:45:02+09:00, 2010:10:11 15:48:18+09:00, 2010:10:11 15:48:45+09:00, 2010:10:11 17:09:16+09:00, 2010:10:11 17:13:23+09:00, 2010:10:11 17:41:46+09:00, 2010:10:11 18:01:57+09:00, 2010:10:11 18:05:53+09:00, 2010:10:11 18:06:39+09:00, 2010:10:11 18:06:51+09:00, 2010:10:13 16:02:09+09:00, 2010:10:14 17:24:32+09:00, 2010:10:14 17:24:45+09:00, 2010:10:14 17:28:40+09:00, 2010:10:15 19:01:30+09:00, 2010:10:15 19:04:20+09:00, 2010:10:15 19:08:23+09:00, 2010:10:15 20:05:01+09:00, 2010:10:15 20:06:22+09:00, 2010:10:15 20:06:57+09:00, 2010:10:15 20:08:57+09:00, 2010:10:15 20:32:55+09:00, 2010:10:15 20:52:57+09:00, 2010:10:15 20:56:37+09:00, 2010:10:15 20:58:02+09:00, 2010:10:17 10:38:42+09:00, 2010:10:17 10:39:56+09:00, 2010:10:17 10:43:33+09:00, 2010:10:17 12:34:21+09:00, 2010:10:17 12:34:57+09:00, 2010:10:17 12:40:45+09:00, 2010:10:17 12:41:01+09:00, 2010:10:17 12:53:14+09:00, 2010:10:17 17:32:49+09:00, 2010:10:17 18:30:45+09:00, 2010:10:18 19:23:31+09:00, 2010:10:18 19:27:19+09:00, 2010:10:18 19:28:41+09:00, 2010:10:18 19:30:06+09:00, 2010:10:18 19:30:31+09:00, 2010:10:20 10:33:45+09:00, 2010:10:20 10:34:29+09:00, 2010:10:20 11:23:20+09:00, 2010:10:20 11:41:54+09:00, 2010:10:20 11:42:40+09:00, 2010:10:24 17:02:09+09:00, 2010:10:24 17:10:32+09:00, 2010:10:24 17:32:03+09:00, 2010:10:24 17:41:53+09:00, 2010:10:24 17:45:26+09:00, 2010:10:24 17:47:17+09:00, 2010:10:24 17:51:16+09:00, 2010:10:24 18:02:56+09:00, 2010:10:24 18:45:43+09:00, 2010:10:24 18:46:17+09:00, 2010:10:24 18:48:33+09:00, 2010:10:24 18:53:18+09:00, 2010:10:24 19:07:54+09:00, 2010:10:24 19:13:45+09:00, 2010:10:24 19:16:58+09:00, 2010:10:24 19:28:48+09:00, 2010:10:24 19:38:37+09:00, 2010:10:24 19:43:10+09:00, 2010:10:24 19:43:53+09:00, 2010:10:24 19:59:52+09:00, 2010:10:24 20:01:08+09:00, 2010:10:24 20:48:14+09:00, 2010:10:24 20:50:58+09:00, 2010:10:24 20:54:02+09:00, 2010:10:24 20:55:52+09:00, 2010:10:24 20:57:29+09:00, 2010:10:24 21:05:10+09:00, 2010:10:24 21:08:18+09:00, 2010:10:24 21:10:16+09:00, 2010:10:24 21:16:20+09:00, 2010:10:24 21:17:43+09:00, 2010:10:25 09:39:16+09:00, 2010:10:25 09:46:29+09:00, 2010:10:25 10:05:38+09:00, 2010:10:25 11:18:53+09:00, 2010:10:25 11:50:26+09:00, 2010:10:25 11:51:05+09:00, 2010:10:25 12:00:13+09:00, 2010:10:25 15:22:59+09:00, 2010:10:25 15:33:05+09:00, 2010:10:25 15:34:24+09:00, 2010:10:25 16:27:38+09:00, 2010:10:25 17:56:05+09:00, 2010:10:25 17:58:21+09:00, 2010:10:26 11:19:59+09:00, 2010:10:26 11:38:02+09:00, 2010:10:26 11:53:47+09:00, 2010:10:26 12:00:05+09:00, 2010:10:26 13:20:07+09:00, 2010:10:26 13:33:22+09:00, 2010:10:26 13:42:01+09:00, 2010:10:26 14:41:18+09:00, 2010:10:26 14:55:20+09:00, 2010:10:26 14:56:06+09:00, 2010:10:26 15:43:36+09:00, 2010:10:26 16:54:38+09:00, 2010:10:26 17:11:44+09:00, 2010:10:26 17:15:13+09:00, 2010:10:26 17:26:13+09:00, 2010:10:26 17:41:55+09:00, 2010:10:26 19:47:22+09:00, 2010:10:26 19:48:14+09:00, 2010:10:26 19:50:03+09:00, 2010:10:26 19:53:22+09:00, 2010:10:26 19:55:51+09:00, 2010:10:26 20:03:58+09:00, 2010:10:27 10:36:49+09:00, 2010:10:27 10:50:55+09:00, 2010:10:27 10:51:57+09:00, 2010:10:27 13:04:07+09:00, 2010:10:27 14:56:21+09:00, 2010:10:27 14:57:04+09:00, 2010:10:27 15:06:48+09:00, 2010:10:27 15:12:12+09:00, 2010:10:27 16:11:25+09:00, 2010:10:27 16:14:47+09:00, 2010:10:27 17:49:54+09:00, 2010:10:27 17:56:38+09:00, 2010:10:27 18:00:04+09:00, 2010:10:27 18:02:55+09:00, 2010:10:27 18:06:11+09:00, 2010:10:27 18:15:50+09:00, 2010:10:28 10:10:44+09:00, 2010:10:28 10:12:08+09:00, 2010:10:29 11:05:10+09:00, 2010:10:29 11:09:04+09:00, 2010:10:29 11:12:36+09:00, 2010:10:29 14:14:59+09:00, 2010:10:29 14:19:19+09:00, 2010:10:31 11:21:12+09:00, 2010:10:31 12:03:41+09:00, 2010:10:31 12:27:29+09:00, 2010:10:31 12:38:58+09:00, 2010:10:31 14:01:06+09:00, 2010:10:31 14:33:27+09:00, 2010:10:31 14:37:06+09:00, 2010:10:31 17:29:07+09:00, 2010:10:31 17:38:27+09:00, 2010:10:31 17:38:32+09:00, 2010:11:01 16:41:38+09:00, 2010:11:01 16:42:04+09:00, 2010:11:01 17:01:09+09:00, 2010:11:01 17:01:45+09:00, 2010:11:01 20:10:11+09:00, 2010:11:04 15:45:50+09:00, 2010:11:04 18:26:47+09:00, 2010:11:04 18:28:53+09:00, 2010:11:04 18:55:39+09:00, 2010:11:04 18:57:34+09:00, 2010:11:04 18:57:47+09:00, 2010:11:04 18:58:28+09:00, 2010:11:09 15:10:18+09:00, 2010:11:09 15:33:34+09:00, 2010:11:09 15:33:40+09:00, 2010:11:09 15:47:40+09:00, 2010:11:09 19:00:39+09:00, 2010:11:12 11:55:13+09:00, 2010:11:12 12:02:54+09:00, 2010:11:12 12:59:38+09:00, 2010:11:12 16:38:16+09:00, 2010:11:19 15:07:10+09:00, 2010:11:19 15:18:59+09:00, 2010:11:19 16:25:01+09:00, 2010:11:19 16:25:33+09:00, 2010:11:19 16:55:42+09:00, 2010:11:19 17:01:09+09:00, 2010:11:19 20:03:44+09:00, 2010:11:22 16:25:49+09:00, 2010:11:22 16:41:56+09:00, 2010:11:22 16:47:14+09:00, 2010:11:22 17:03:37+09:00, 2010:11:22 17:34:28+09:00, 2010:11:24 11:56:29+09:00, 2010:11:24 15:22:26+09:00, 2010:11:24 15:24:15+09:00, 2010:11:25 11:20:54+09:00, 2010:11:25 11:28:36+09:00, 2010:11:25 11:30:35+09:00, 2010:11:25 11:33:32+09:00, 2010:11:25 11:33:58+09:00, 2010:11:25 13:00:37+09:00, 2010:11:25 14:11:30+09:00, 2010:11:25 14:41+09:00, 2010:11:25 14:50:31+09:00, 2010:11:25 15:07:12+09:00, 2010:11:25 15:17:48+09:00, 2010:11:25 15:25:44+09:00, 2010:11:25 15:43:59+09:00, 2010:11:25 15:50:41+09:00, 2010:11:25 15:57:31+09:00, 2010:11:25 16:09:37+09:00, 2010:11:25 16:43:25+09:00, 2010:11:25 18:13:35+09:00, 2010:11:25 18:13:57+09:00, 2010:11:26 13:14:37+09:00, 2010:11:30 18:26:18+09:00, 2010:11:30 18:35:40+09:00, 2010:11:30 19:37:53+09:00, 2010:11:30 20:11:12+09:00, 2010:11:30 20:17:35+09:00, 2010:12:01 10:01:19+09:00, 2010:12:01 10:10:56+09:00, 2010:12:01 10:15:49+09:00, 2010:12:01 10:25:34+09:00, 2010:12:02 20:32:39+09:00, 2010:12:02 20:59:55+09:00, 2010:12:02 21:01:08+09:00, 2010:12:02 21:12:15+09:00, 2010:12:02 21:27:16+09:00, 2010:12:02 21:33:22+09:00, 2010:12:03 10:36+09:00, 2010:12:03 10:36:49+09:00, 2010:12:03 11:15:44+09:00, 2010:12:03 11:26:22+09:00, 2010:12:03 13:19:19+09:00, 2010:12:06 15:35:50+09:00, 2010:12:09 11:08:44+09:00, 2010:12:09 11:29:25+09:00, 2010:12:09 12:00:13+09:00, 2010:12:09 16:50:23+09:00, 2010:12:10 10:22:42+09:00, 2010:12:10 10:30:36+09:00, 2010:12:10 10:36:59+09:00, 2010:12:10 11:10:07+09:00, 2010:12:10 16:09:23+09:00, 2010:12:10 16:10:08+09:00, 2010:12:10 16:34:36+09:00, 2010:12:10 16:51:07+09:00, 2010:12:15 17:34:07+09:00, 2010:12:15 18:10:41+09:00, 2011:01:13 10:44:40+09:00, 2011:01:13 10:46:54+09:00, 2011:01:13 14:54:30+09:00, 2011:01:14 10:23:26+09:00, 2011:01:20 10:33:28+09:00, 2011:01:20 10:47:49+09:00, 2011:01:20 13:06:18+09:00, 2011:01:20 13:31:11+09:00, 2011:01:20 13:34:50+09:00, 2011:01:20 13:40+09:00, 2011:01:20 13:42:53+09:00, 2011:01:20 13:44:03+09:00, 2011:01:20 13:46:29+09:00, 2011:01:20 13:47:41+09:00, 2011:01:20 13:49:49+09:00, 2011:01:20 13:57:22+09:00, 2011:01:20 15:28:30+09:00, 2011:01:20 15:43:08+09:00, 2011:01:20 15:43:14+09:00, 2011:01:20 15:50:58+09:00, 2011:01:20 16:15:12+09:00, 2011:01:25 10:21:56+09:00, 2011:01:25 10:30:52+09:00, 2011:01:25 13:45:56+09:00, 2011:01:25 15:12:45+09:00, 2011:04:28 19:13:20+09:00, 2011:04:28 19:13:20+09:00, 2011:06:14 10:16:28+09:00, 2011:06:14 11:12:42+09:00, 2011:06:14 11:14:01+09:00, 2011:06:14 11:58:20+09:00, 2011:06:14 11:59:56+09:00, 2011:06:14 13:10+09:00, 2011:06:14 19:08:11+09:00, 2011:06:16 17:46:31+09:00, 2011:06:22 14:40:59+09:00, 2011:06:22 16:19:03+09:00, 2011:06:22 16:55:58+09:00, 2011:06:22 17:22:30+09:00, 2011:06:22 17:23:55+09:00, 2011:06:24 09:30:07+09:00, 2011:06:24 14:56:23+09:00, 2011:06:24 14:56:39+09:00, 2011:06:24 15:00:17+09:00, 2011:06:24 15:04:40+09:00, 2011:06:29 10:38:42+09:00, 2011:10:07 10:16:42+09:00, 2011:10:07 10:46:26+09:00, 2011:10:07 11:06:51+09:00, 2011:10:07 11:09:27+09:00, 2011:10:07 11:20:46+09:00, 2011:10:13 18:43:57+09:00, 2011:10:13 18:57:01+09:00, 2011:10:13 18:57:59+09:00, 2011:10:13 19:30:21+09:00, 2011:10:18 15:58:17+09:00, 2011:10:18 16:00:33+09:00, 2011:10:18 16:06:10+09:00, 2011:10:18 20:19:33+09:00, 2011:10:19 15:27:49+09:00, 2011:10:20 11:07:39+09:00, 2011:10:20 11:14:39+09:00, 2011:10:20 11:54:11+09:00, 2011:10:20 12:00:05+09:00, 2011:10:20 12:46:30+09:00, 2011:10:20 12:48:44+09:00, 2011:10:20 13:04:07+09:00, 2011:10:20 13:24:19+09:00, 2011:10:20 13:28:21+09:00, 2011:10:20 15:51:35+09:00, 2011:10:20 16:06:11+09:00, 2011:10:20 16:09:56+09:00, 2011:10:20 16:12:27+09:00, 2011:10:20 16:59:04+09:00, 2011:10:20 17:00:26+09:00, 2011:10:21 09:38:21+09:00, 2011:10:21 10:05:10+09:00, 2011:10:21 10:27:37+09:00, 2011:10:21 10:46:50+09:00, 2011:11:01 18:48:09+09:00, 2011:11:02 08:53:48+09:00, 2011:11:02 09:05:43+09:00, 2011:11:03 10:27:24+09:00, 2011:11:03 10:32:26+09:00, 2011:11:03 10:33:21+09:00, 2011:11:04 11:41:05+09:00, 2011:11:04 13:42:16+09:00, 2011:11:07 18:25:23+09:00, 2011:11:08 10:04:51+09:00, 2012:01:31 15:01:06+09:00, 2012:01:31 15:03:55+09:00, 2012:02:23 10:01:21+09:00, 2012:02:23 10:01:22+09:00, 2012:02:23 12:37:20+09:00, 2012:02:23 12:38:08+09:00, 2012:02:23 13:40:40+09:00, 2012:02:23 13:40:42+09:00, 2012:02:23 13:49:48+09:00, 2012:02:23 13:49:53+09:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0
History Changed                 : /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata
Derived From Instance ID        : xmp.iid:D97BA31CCE5DE1119D9EB07065E3A2A3
Derived From Document ID        : xmp.did:BD7C5823AFD2DF1185BFE72C625F81A3
Derived From Original Document ID: xmp.did:BD7C5823AFD2DF1185BFE72C625F81A3
Derived From Rendition Class    : default
Doc Change Count                : 6033
Format                          : application/pdf
Title                           : 
Creator                         : 
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Has XFA                         : No
Page Count                      : 112
Page Layout                     : SinglePage
EXIF Metadata provided by EXIF.tools

Navigation menu