Planex Communications BT-06HS-C Bluetooth headset User Manual
Planex Communications inc. Bluetooth headset Users Manual
Users Manual
3. Turn on/ Turn off
4. Pairing with your mobile phone
It need to pair with your Bluetooth device, first time.
5. How to wear the headset
4. "BT-06HS-C” will show on certain items in your mobile phone.
5. Key in pairing pin code "0000”press " yes" , the indicator
light will turn from the blue/red flashing status into blue
flashing, it means the pairing has been successful.
6.Now the headset has been in the "connected mode".
you may receive or dial the phone call.
5 Sec
- Stand-by mode-------
blue light flash once every 5 Sec.
- C
blue light flash two times every 5 Sec.
- Active call mode-----
blue light flash three times every 5 Sec.
- low battery-----
red light flash.
onnected mode----
Choose the ear tip size
Choose the ear plug size
3 Sec
Power on - blue light flashing.
Power off - red light flashing then off.
10cm~1m
The pairing
distance Devices found
BT-06HS-C
Red blue
Press the MFB key for about
3 Sec, to turn on and turn off.
1.Before pairing, make sure your
headset is off.
2.Press the MFB key for at least
5 sec; the blue and red light
flashing alternately it means the
headset is in the “pairing mode".
3.Please ensure that your mobile
phone is provided the Bluetooth
Function, and activate the function.
large one on headset already
Bluetooth Standard
Talktime
Standby time
Charging time
Supported Bluetooth profiles
Operating temperature range
Storage temperature
Operation range
Power Supply
Over 5 .
Over 120
Within 90 ~120Mins.
10 meters(open space)
Handsfree / Headset .
Bluetooth V2.1
hrs
hrs.
0 ~ 55 'C
0% ~ 90% (non-concrete status)
5V DC, 00~240V AC adapter
Specification of the Headset
1. Charging the Headset
1. At least for 4 hours when first time charging,
2. When charging, the red light on; fully charged the light
will be off.
2. Introduction of the product
Bluetooth Headset
User Manual
BT-06HS-C
LED light indicator
Speaker
Ear plug
Hook point
Ear tip
Charging Port
Microphone
Volume key
MFB key
USB
Port
Charging Plug
Model: BT-06HS-C
FCC ID. : SJ9-BT-06HS-C
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATIONS IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
( 1 ) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
( 2 ) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFEERENCE THAT MAY UNDESIRED OPERATION.
Made in Taiwan Brand Name:PCI
Cap the ear tip
6. How to wear it firmly
X
Parallel
To make a call, dial through your mobile phone.
10. Answer a call.
11. Voice dialing
12. Redial last number
13. Volume control.
Mute & un-mute
Press 2 Sec
If you can't wear it firmly, use the ear hook as assist
9. End a call.
--- - ---- - -
Click
Double-Click
----------
Click
---------- ----------
Click
---------- ----------
1.When during call press the “ MFB &
Vol key” you will hear
a “ Do-lu-do-do" sound, then your
voice won't be heard.
2.Click the Vol key again, to un-mute
the microphone.
Simultaneously,
7. Make a call.
8. Reject a call.
microphone toward jaw
----------
Inserted
completely
X
Inserted
Incompletely
Inserted
Incompletely
Inserted
Incompletely
The ear tip must insert to ear bone completely.
When you hear the in-coming
call rings from your headset;
press the MFB key for 2 Sec,
when you hear the " Do Do"
sound than release it. -------
Reject a call.
2 Sec
Click
Click
When you finish a call; click the
MFB key to end the call.
When you have a incoming call click
the MFB key after you hear the ring
from the headset.
1.The headset should be under
"Connected mode", click the MFB
key; then you can make the " Voice
dialing " by the mobile phone's
operation instruction..
2.This function depends on the
specification of your mobile phone.
1.The headset should be under
"Connected mode". By double-click
the MFB key, after you hear a " Do-
Do " sound from the headset, then it
will redial again.
2.This function depends on the
specification of your mobile phone.
You can adjust the headset volume
during a call.
Press / Click
Click
left ear right ear
The salient insert
in the little hole
LL
Press and hold continuously.
Click continually.
Ringing.....
Ringing.....
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. (Example - use only shielded interface cables
when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment.