Plantronics BBS Stereo Bluetooth/Corded Headset User Manual BBS

Plantronics Inc Stereo Bluetooth/Corded Headset BBS

BBS-User Manual

The rst time you power on your headphones, thepairing process begins.1Slide the power switch on. You hear "pairing" andthe LEDs ash red and blue. GET PAIRED 2Activate Bluetooth on your phone and set it tosearch for new devices.•iPhone Settings > Bluetooth > On*•Android Settings > On > Scan for devices**Menus may vary by device.3Select “PLT_SLB.”If necessary, enter four zeros (0000) for thepasscode or accept the connection.Once successfully paired, you hear “pairingsuccessful” and the LEDs stop ashing. ([ ])HEADPHONE OVERVIEW Play/pause musicTap the Play/pause button.VolumeRotate the volume wheel forward (+) orbackward (–) to control the volume.Track selectionTap the Forward button or Back button tocontrol the track selection.Open micTap the red button to hear your naturalsurroundings.Voice dial (smartphone)If your smartphone has a voice-enabled assistant,press and hold the Call button for 3 secondsand wait for the phone prompt.Answer a callChoose:•Put on the headset to answer call, or•Tap the Call button End a callTap the Call button to end current call.Decline a callPress and hold the Call button for 2 seconds.MuteDuring a call, press the red button. You hear"mute on/o." While muted, taking o theheadphones transfers the call to your phone.Call back last call (smartphone)To dial your last number you dialed, double-tapthe Call button.It takes up to 2 hours to fully charge yourheadphones. The LEDs turn o once charging iscomplete. ===== Tip: To check the headphones battery status, tap the Callbutton while wearing your headphones. Headphonesmust be in idle state.Your headphones have up to 12 hours of listeningtime.CHARGEAdjust the headphones for a comfortable t.Lengthen or shorten the band until it tscomfortably. ADJUST THE FIT
1Slide and hold the power button towards theBluetooth icon until the LEDs ash red and blue.2Activate Bluetooth on your second device andfollow steps 2 and step 3 in "Get Paired." PAIR SECOND DEVICESmart sensors respond when you put on or takeo your headphones.Putting on your headphones will:•Resume music•Answer a callTaking off your headphones will:•Pause music (while music is playing)•Transfer active call to phoneDisable sensorsTo disable the sensors, hold both the Mute andCall buttons for more than 6 seconds until theLED ashes purple then red. Repeat to reactivate;the LED ashes purple then blue.USE SENSORSWhen the battery is exhausted use yourheadphones with the provided 3.5 mm Applecable.Use the cable to:•Adjust the volume with the (+) and (–) buttons.•Play/pause music or answer/end a call with the button = single tap• Track forward with the button = double tap• Track backward with the button = triple tap•Activate Siri with the button = 3 second pressHYBRID_MODETo enable HD voice (wideband), hold both the redbutton and Play/pause buttons for more than6 seconds until the LEDs ashes purple. Repeat todisable.HD voice functions properly when both devices support it.ENABLE HD VOICEIf your Mac is Bluetooth-enabled, you can pairyour headset to it.1Place your headset in pair mode (slide and holdthe power button towards the Bluetooth icon).2On you mac, choose Apple menu > SystemPreferences.3Click Set Up New Device (+), select "PLT_SLB" andfollow the onscreen instructions.PAIR TO MACYou can change the language and other settingsby downloading Plantronics Hub for Windowsand Mac at plantronics.com/software. You canalso download the free mobile apps PlantronicsHub for iOS and Android.Plantronics Hub enables you to:•Change language (Plantronics Hub for Windowsand Mac only)• Receive rmware updates (Plantronics Hub forWindows and Mac only)• Turn "mute o" voice alert on/o• Turn smart sensors on/oCUSTOMIZEGET STARTEDSUBLIMEDesigned in Santa Cruz, CaliforniaRead the guides for setup, use and safety. Formore help, don’t return to the store; nd a localphone support number at plantronics.com/support.NEED MORE HELP?© 2014 Plantronics, Inc. All Rights Reserved. Bluetooth isa registered trademark of Bluetooth SIG, Inc. and any useby Plantronics is under license. iPhone is a trademark ofApple, Inc. All other trademarks are the property of theirrespective owners.Patents: U.S. 5,712,453; 7,039,179; Patents pending.200462-XX 11.14 MODEL ID: PITE14
FCC statement ·This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ·These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. ·If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. The measured SAR levels evaluated are in compliance with the FCC RF exposure guidelines. .
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. IC Radiation Exposure Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. NCC警語 低功率電波輻性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機,非經許可,公司,商號或使用者均不得擅自變更頻率,加大功率或變更原設計之特性及功能。第十四條 低功率射頻電機之使用不得影響飛航影響安全及干擾合法通信,經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信, 指一電信法規定作業之無線電通信低功率射頻電機需忍受合法通信或工業,科學及醫療用電波輻射性電機設備之干擾。

Navigation menu