Plantronics Cs50 Owners Manual PIB V8
2014-07-31
: Plantronics Plantronics-Cs50-Owners-Manual plantronics-cs50-owners-manual plantronics pdf
Open the PDF directly: View PDF 
.
Page Count: 9
| Download | |
| Open PDF In Browser | View PDF |
CS50 WIRELESS OFFICE HEADSET SYSTEM PRODUCT INFORMATION BOOKLET BASICS WELCOME BASICS This Product Information Booklet contains information not described in the Quick Start Guide* (QSG). The QSG should be used to set up your CS50 Wireless Office Headset System. BASICS Installation . . . . . . . . . . . . 2 Location . . . . . . . . . . . . . . 3 Headset/Handset Mode . . . 3 Placing and Receiving a Call Using Headset . . . 4 Placing and Receiving a Call Using Handset . . . 4 OPTIONS Optional Handset Lifter Use . . . . . . . . . . . . . 7 IntelliStand Function . . . . . 8 Switching to Handset . . . . . 8 FEATURES Out of Range Warning . . . 5 Low Battery Warning . . . . . 5 Recharging Headset . . . . . 6 Replacing Battery . . . . . . . 6 SUBSCRIPTION . . . . . . . . 12 TIP LOCATION TM TROUBLESHOOTING . . . . 9 TECHNICAL SUPPORT . . 11 SYSTEM RESET . . . . . . . . 13 MAINTENANCE. . . . . . . . 13 PARTS & ACCESSORIES . . 14 *This Product Information Booklet and Quick Start Guide are available on-line at www.plantronics.com/documentation. Do not position the CS50 system near other electronic equipment. Incorrect positioning can cause problems with noise or interference. HEADSET/HANDSET MODE Pressing the talk button 14 * on the headset selects headset mode. The talk indicator 2 on the base unit will illuminate green and the talk indicator light 17 on the headset will also illuminate when in headset mode. Both of the indicators are off when in handset mode. By selecting handset mode after completing your call, you will conserve the headset battery power and extend the remaining available talk time. You can achieve this by pressing the talk button immediately on conclusion of the call. TALK BUTTON 14 INSTALLATION Please install the CS50 Wireless Office Headset System in accordance with the instructions detailed in the QSG. 2 * 14 17 Callouts have been first identified in the Examine Component section of the QSG. 3 BASICS NOTE OUT OF RANGE WARNING To place a call using the headset, the system must be in headset mode. Take the handset off hook and dial in the normal way. You will then be able to talk through your headset. When the call is complete, return the telephone handset to the cradle. As you walk away from the base unit you will eventually reach the system operating range limit. When in headset mode a warning alert of two beeps will sound in the headset shortly before you meet the range limit. RECEIVING A C ALL USING YOUR HEADSET On hearing this alert you should walk closer to the base unit to ensure call quality is maintained. When your telephone rings take the handset off hook. Ensure that your CS50 Wireless Office Headset System is in headset mode. You will then be able to talk through your headset. If you remain out of range for more than 15 minutes the system will drop the call permanently. If using a Plantronics Handset Lifter the handset will be replaced and the call terminated. When the call is complete, return the telephone handset to the cradle. PLACING AND RECEIVING A C ALL USING HANDSET In handset mode the telephone can be used to make and receive calls in the normal way. Ensure that your CS50 Wireless Office Headset System is in handset mode. 4 FEATURES FEATURES If you have installed a Plantronics Handset Lifter please refer to the sections “Making and Receiving a call using the Lifter” on page 7. PLACING A C ALL USING YOUR HEADSET LOW BATTERY WARNING When the headset battery is running low (approximately 5 minutes talk time remaining), an audible warning will be heard through the headset as a single beep repeating every 10 seconds. Soon after hearing this warning, you should recharge the headset. 5 RECHARGING THE HEADSET To recharge the headset, place it into the charge cradle 1 in the base unit. During charging, the charge indicator 9 on the base unit will flash amber. 1 When the headset is fully charged, the charge indicator on the base unit will stop flashing and remain illuminated. FEATURES 9 A completely depleted headset requires a minimum charge time of 1 hour before use, and 3 hours to fully charge. Should it be necessary to replace the headset battery at anytime please refer to the diagrams below. SETTING UP THE OPTIONAL HANDSET LIFTER Use the directions provided with the handset lifter to set it up. MAKING A C ALL USING THE HANDSET LIFTER Press the talk button on the headset. The handset lifter will raise the telephone handset off hook. You will then hear a dial tone in your headset and can proceed to make a call as normal. When you finish your call press the talk button. The handset lifter then lowers the handset to end the call. RECEIVING A CALL USING THE HANDSET LIFTER When a new call is received the telephone rings as normal, but in addition, a ring alert of three short beeps will be heard in your headset, also the headset talk indicator light will flash. 1 2 To answer the call press the talk button on the headset. The handset lifter will then raise the telephone handset off hook and you will be able to talk to the caller. 3 4 5 6 PLANTRONICS OPTIONS REPLACING THE HEADSET BATTERY OPTIONS NOTE The ring alert feature (audio and visual) is only active when the handset lifter is connected. When you have finished your call, press the talk button on your headset. The handset lifter then lowers the handset to end the call. 7 TROUBLESHOOTING TM INTELLISTAND FUNCTION 10 OFF OPTIONS ON When the CS50 Wireless Office Headset System is used in conjunction with a Plantronics Telephone Handset Lifter, you can enable the IntelliStand feature. The IntelliStand senses when the headset has been removed or placed in the CS50 base unit, automatically activating the lifter and enabling headset/handset mode to answer or end a call. SYMPTOM I cannot hear caller/dial tone. 2 3 The IntelliStand feature is disabled (off) when the IntelliStand switch 10 is in position I (up), or enabled (on) when the switch is in position II (down). SWITCHING FROM HEADSET TO HANDSET WHEN USING THE HANDSET LIFTER Callers cannot hear me. 13 SWITCHING FROM HANDSET TO HEADSET WHEN USING THE HANDSET LIFTER If during a call you are using the telephone handset and want to switch to your headset, press the talk button on the headset. The handset lifter will raise and you will be able to continue the call using your headset. Place the telephone handset on the handset lifter. When the call is finished press the talk button on your headset. The handset lifter will lower the handset and end the call. 8 12 * 1 2 • Try other telephone configuration dial 4 settings on the base unit. Ensure the selected number is directly in line with the horizontal position indicator. See Step 4.4 in the QSG. • Increase the speak volume fine tune 13 on the base unit. If the volume is still too low, increase the talk volume master setting 12 on the bottom of the base unit. • Check that the mute function is off. See Step 5.2 in the QSG. 3 ... Callouts refer to Quick Start Guide (QSG) for details of corresponding numbered features. 9 TROUBLESHOOTING If during a call you are using your headset and want to switch to the telephone handset, remove the handset from the handset lifter, then press the talk button on your headset. The handset lifter will lower and you will then be able to continue the call using the handset. 11 4 SUGGESTION • Check that all cords and jacks are connected correctly. • Check that the base has power (power indicator 3 * is red) and the headset battery is fully charged. • Try other telephone configuration dial 4 settings on the base unit. Ensure the selected number is directly in line with the horizontal position indicator. See Step 4.4 in the QSG. • Ensure you are in headset mode. Press the talk button to select correct mode. The talk indicator 2 light on the base is on (green). • Select another listen volume master 11 setting on the base. SYMPTOM SUGGESTION People I talk to can hear a buzz in the background. •Your phone may be sensitive to 900 MHZ. Move the CS50 base further away from your phone. •If the AC Adapter is plugged into a power strip, try plugging it into the wall directly. •Call TAC for a RF filter. I can hear beeps in the headset. •One beep every 10 seconds is caused by a low battery warning. Recharge battery by returning it to the base charge cradle for one to three hours until charge light stays lit or quits blinking. •Two beeps is an out of range warning. Move closer to the base. •Three rapid beeps every 15 seconds indicates your mute is on. Press the mute control 15 dial once to turn mute off. •When an optional lifter is connected, three repetitive beeps indicate a call is coming into the headset. Press the talk button on the headset to answer the call. 15 10 SUGGESTION I can hear too much echo or sidetone. • Lower the speak volume fine tune 13 on the base unit. • If the volume is still too high, lower the speak volume master 12 setting. See Step 5.4 and 5.5. in QSG. My handset lifter operates every time I remove or replace my headset in the base unit. • Disable the IntelliStand function by moving the IntelliStand switch 10 to position I (off). Battery talk time performance • Replace battery with a new battery is significantly degraded even pack. Refer to the diagrams on after a full recharge. page 6. Headset is uncomfortable when worn in over-the-ear mode. • Try changing earloop sizes. Experiment to find the best fit. Suddenly the call is dropped. • Try to reset the system. See page 13. (Talk indicator on the headset If this does not work, try the and base will not be re-subscription procedure on page 12. illuminated.) I hear static that does not allow me to communicate. • Try to re-establish a link by pressing the headset talk button. If that does not work, try resetting the base unit. See Step 4 of System Reset on page 13. Last, try the whole System Reset procedure on page 13. The Plantronics Technical Assistance Center (TAC) is ready to assist you! Dial (800) 544-4660 x 5538 Sunday 5 P.M. through Friday, 5 P.M. Pacific Time or visit the Support section of our website at www.plantronics.com. Contact TAC for accessibility information. 11 TROUBLESHOOTING TROUBLESHOOTING Receive sounds distorted. •Move the CS50 base unit further away from telephone or computer. •If your telephone has a receive volume control, lower your telephone volume 15 until the distortion disappears. •Lower the listen volume 15 control on the headset. If the distortion persists, lower the listen volume master 11 setting on the 11 back of base. See Step 5.1 and 5.2 in the QSG. •Perform system reset. See page 13. SYMPTOM SUBSCRIPTION 2. 1. Return the headset to the headset charge cradle. 2. Press and hold both the talk volume fine tune buttons on the base unit for a minimum of 5 seconds. The power indicator 3 will then flash (red). 3. 3. Press and hold the headset mute control button for a minimum of 5 seconds. The talk indicator light 17 on the headset will then illuminate (green). Successful re-subscription is indicated when the power indicator is fully illuminated and the talk indicator light is off. 17 SUBSCRIPTION 3 4. To complete the process, reset the base unit by disconnecting the AC power adapter 24 from the AC power adapter jack 7 for 5 seconds, then reconnect. 5. If re-subscription fails within 2 minutes the headset will return to the un-subscribed state. Try the re-subscription process again or call Technical Support (page 11). 12 To recover from some fault conditions (refer to the Troubleshooting Section) you may need to perform a system reset. To perform the system reset follow this procedure: 1. Press both the talk button 14 and the mute control button on the headset for 5 seconds. 2. When the talk indicator light release both buttons. 17 15 on the headset blinks, 3. Press the talk button again. 4. Next reset the base unit by disconnecting the AC power adapter 24 from the AC power adapter jack 7 for 5 seconds, then reconnect. The system reset operation is complete. MAINTENANCE 1. Unplug the unit from the telephone and the AC adapter from the power source before cleaning. 2. Clean the equipment with a damp (not wet) cloth. 3. Do not use solvents or other cleaning agents. 13 SYSTEM RESET/MAINTENANCE The headset and base unit are supplied subscribed to each other. However, if you wish to use a replacement headset with the base unit then the units must be re-subscribed as follows: SYSTEM RESET PARTS & ACCESSORIES PARTS & ACCESSORIES P/N DESCRIPTION P/N DESCRIPTION 64394-11 Earloops–pack of 3 66735-01 Over-the-Head Band 43937-01 Replacement Cushions Foam (2) 67063-01 Replacement Cushions Leatherette (2) 64397-01 Behind-the-Head Neckband with Adapter 64395-11 Over-the-Head Band with Tripod Tripod CS5 WIRELESS 0 OFFIC HEADSET SYSTEME 64416-01 Quick Start Guide* PRODUCT INFORMAT PLA N 60961-11 NI C KLET S HL10 Telephone Handset Lifter On-line Indicator 64399-01 Battery 64400-01 Battery Door 64401-01 AC Adapter 66291-01 Double Filter Cord 64396-11 64402-11 CS50 Headset For information on spare par ts and accessories, call Plantronics at (800) 544-4660 x5538, or visit the Plantronics website at www.plantronics.com. *This Product Information Booklet and Quick Start Guide are available on-line at www.plantronics.com/documentation. 14 PARTS & ACCESSORIES PARTS & ACCESSORIES 65116-01 TR O ION BOO 15 345 Encinal Street Santa Cruz, California 95060 (800) 544-4660 www.plantronics.com © 2003 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Plantronics and the logo design combined, and IntelliStand are trademarks or registered trademarks of Plantronics, Inc. All other trademarks are the property of the respective owners. Patent U.S. 5,210,791 and Patents Pending Printed in China 63915-01 (7-04 )
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes X Press Private : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%DocumentCustomColors: (PANTONE 286 C).%%+ (PANTONE 286 ).%%+ (PANTONE 138 C).%%CMYKCustomColor: 1 .66 0 .02 (PANTONE 286 C).%%+ 1 .66 0 .02 (PANTONE 286 ).%%+ 0 .42 1 .01 (PANTONE 138 C).%%EndComments Create Date : 2004:07:28 16:26:17Z Creator : QuarkXPress(tm) 6.1 Modify Date : 2004:08:26 04:22:53-07:00 Page Count : 9 Page Mode : UseThumbs Creation Date : 2004:07:28 16:26:17Z Producer : QuarkXPress(tm) 6.1 Mod Date : 2004:08:26 04:22:53-07:00 Metadata Date : 2004:08:26 04:22:53-07:00 Title : CS50 PIB v8EXIF Metadata provided by EXIF.tools