Platform2 UD-1404S Subwoofer User Manual UD 1404S

Platform2 International Limited Subwoofer UD 1404S

User manual

Download: Platform2 UD-1404S Subwoofer User Manual UD 1404S
Mirror Download [FCC.gov]Platform2 UD-1404S Subwoofer User Manual UD 1404S
Document ID2678800
Application ID3X6qlbj6IAaOYfMj35MuWw==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize75.63kB (945336 bits)
Date Submitted2015-07-14 00:00:00
Date Available2015-07-14 00:00:00
Creation Date2015-07-10 16:18:09
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2015-07-10 16:18:09
Document TitleMicrosoft Word - UD-1404S User manual
Document CreatorPScript5.dll Version 5.2
Document Author: Administrator

A5 SIZE

IMMERSE UD‐1404 and UD‐1404S User Manual
2.1 Wi‐Fi / Bluetooth Multi‐Room Sound Bar with Wireless Subwoofer
* Please read the instructions carefully before using the system and keep the manual
for future reference.
Table of Content
Inside the Box
Precautions
Product Introduction
Overview
Soundbar
Subwoofer
Remote Control
Setup IMMERSE
Placement
Connect to TV
Connect to DVD player
Connect to other devices
‐ Wi‐Fi
‐ Bluetooth
‐ Ethernet
‐ Aux‐in / Analog / Optical / Coaxial
Multi‐Room
Sound Effect Mode
Firmware Update
Troubleshooting
Inside the Box
Carefully unpack the carton and confirm that the following parts are included.
• IMMERSE Wi‐Fi / Bluetooth sound bar
• Subwoofer
• Remote control
• AC adaptors
• Manual
Precautions
* Please read these safety instructions carefully to ensure your safety.
• Do not use this product where contact with moisture, liquids, humidity or rain is
possible to avoid electric shock and operating damage.
• Avoid exposing this product to direct sunlight, stove tops or any other heat sources
to prevent operating damage.
• Do not cover the ventilation openings – this may cause overheating, damage to the
product, and a hazardous condition.
• Do not drop, disassemble, deform, modify or insert any objects into this product as
operating damage will result.
• Do not attempt to repair, modify or disassemble the product yourself. This product
does not contain any user‐serviceable components.
• Do not clean the product with alcohol, ammonia based cleaners, abrasive cleaners
or wet cloth. Only clean with a soft dry cloth.
• Do not place this product on its side, on slanted surfaces as well as near the edge
of high surfaces, like shelves. Take care to prevent accidental falling. The product
may vibrate while playing music, which cause it to move and fall off a surface.
• Do not bring your product in to contact with any sharp objects as this may cause
scratches and operating damage.
• Observe all signs and displays that require an electrical device or RF radio product
to be switched off in designated areas.
• Dispose of the product in accordance with local laws and regulations.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates use and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
FCC Notice
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
FCC Caution
• Any changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate this equipment.
• This device and its antenna(s) must not be co‐located or operating in conjunction
with any other antenna or transmitter.
FCC ID: NKTUD‐1404, NKTUD‐1404S
To locate the FCC and IC id‐entification numbers, please look on the underside of the
IMMERSE.
Model number UD‐1404,UD ‐1404S
The crossed‐out wheelie bin symbol means that the product must be disposed of
separately in the European Union. These products must not be disposed of with
unsorted household waste.
Product Introduction
The iui DESIGN UD‐1404 “IMMERSE” multi‐room 2.1 sound bar is a breakthrough in
providing high performance audio to your TV and also the whole home. You’re in
control – you can use sound bar with other iui DESIGN Wi‐Fi speakers. And the
configuration options are almost limitless.
Historically, if you wanted to listen to music from your TV or digital device, you could
connect to your speaker with a 3.5mm audio cable, or Bluetooth. But IMMERSE
provides you breakthrough flexibility. While it connects via an audio cable and
Bluetooth, it also can connect by Wi‐Fi and wired Ethernet.
And by using Wi‐Fi or wired Ethernet, you can create a whole home audio system, so
that you have music distributed throughout your home.
To get the best experience from IMMERSE, it’s good to understand some basics. First
and foremost, you can simply connect the product by using the 3.5mm audio line in
or Bluetooth if you want to just connect a TV to the sound bar. But to play your music
to the sound bar and also to other Wi‐Fi speakers, you need to take a few additional
steps. But, let’s first walk through the basics…
Since IMMERSE is a very high‐performance sound bar with amazing technology
capability, you have options to meet your lifestyle. First, you need to decide how to
connect your TV and other digital devices to the product, and what the trade‐offs are
for each type of connection.
3.5mm Audio Line‐in:
If you use the 3.5mm stereo audio line in, you can simply connect your audio source
to IMMERSE, and you can enjoy high performance audio. Of course, you will be
limited to one IMMERSE sound bar and you have to remain physically connected.
Bluetooth:
Bluetooth is a simple wireless connection to connect your digital source to your
IMMERSE. Bluetooth technology only connects from one source (your TV or other
digital source, like a PC or Smartphone) to one speaker, such as IMMERSE sound bar.
And Bluetooth has lower sound performance than a wired 3.5mm audio connection,
due to compression of the signal during wireless transmission. Its range is also
limited, typically to one room.
Wi‐Fi:
Using Wi‐Fi, you can connect your Wi‐Fi digital source (such as your TV, PC, Mac,
tablet, smartphone, etc) to the IMMERSE sound bar or more Wi‐Fi speakers. The
benefit of Wi‐Fi over Bluetooth is important – Wi‐Fi allows you to stream one source
to IMMERSE sound bar and other iui DESIGN Wi‐Fi speakers all over your house
(because Wi‐Fi typically has longer range), and the bandwidth of Wi‐Fi is much higher
than Bluetooth, so the quality of the sound performance is essentially the same as a
3.5mm wired audio connection.
Of course, Wi‐Fi performance in the home is influenced by many factors – the quality
of your wireless router, how many people are connected to the router and
downloading at the same time, the number of routers that are active (which is really
important in high‐density housing such as apartment buildings).
In general, we recommend a maximum of one IMMERSE and two iui DESIGN Wi‐Fi
speakers connected to your router. More is possible if you take certain technical
steps to improve your bandwidth – but that discussion is beyond the scope of this
manual.
And Wi‐Fi performance is impacted by the capability of your Wi‐Fi enable digital
device – for example, an iOS based product such as an iPhone can only reliably
connect to one Wi‐Fi device at a time. But if you use iTunes on your PC or Mac, you
can connect to multiple Wi‐Fi speakers. You can also use Android smartphones,
tablets and PC’s to connect using a standard known as DLNA, and connects to
multiple Wi‐Fi speakers.
Wired Ethernet:
Wired Ethernet, where the IMMERSE is connected to your router or Ethernet switch
with an Ethernet cable will give you the best performance. You can typically
connect many more than three Wi‐Fi speakers. Ultimately, there is a limitation of
your router or Ethernet switch, but for most standard residential users this is not a
factor. And wired Ethernet will give you the audio performance of a 3.5mm wired
connection.
So the first decision you will have to make is how you want to connect to IMMERSE.
Once you make that decision, then you can follow the easy steps in this manual to
start enjoying your music.
If you are using an iPhone or /and Android device, we have an app that makes it easy
to set‐up your IMMERSE. You can use the app to connect the IMMERSE to your home
network, you can name it (Living Room, Bedroom, Den), and you can assign
IMMERSE and other iui DESIGN Wi‐Fi speakers to groups, so that you can play your
music to one, some or all Wi‐Fi speakers and sound bar.
The IMMERSE application also updates the software on your IMMERSE sound bar,
keeping it current and up to date. The IMMERSE application does not take the place
of your music player software, such as iTunes, Windows Media Player or streaming
music service applications such as Pandora. The application lets you configure your
IMMERSE speakers, and then you use your favorite applications to select and play
music.
Overview
Sound Bar
Front
Touch panel
POWER – Switch the soundbar and subwoofer on or to standby.
SOURCE – Select an input source for the soundbar.
MFB – Activate Bluetooth pairing mode in Bluetooth mode.
VOL+ / VOL ‐ – Increase or decrease volume.
SUB –Activate soundbar and subwoofer pairing mode.
LED display panel – Show audio input selection
NFC sensor – Pair with Bluetooth enabled devise with NFC feature
Back
Power ‐ Switch the soundbar and subwoofer on or to standby.
DC jack – Connect with power source.
AUX IN – Connect to an audio source with a 3.5mm audio line‐in cable.
Analog line‐in (L / R) – Connect to an audio source with a RCA cable.
Coaxial line‐in – Connect to an audio source with a coaxial cable.
Optical line‐in – Connect to an audio source with a digital optical cable.
RJ45 Ethernet jack – Connect to a Wi‐Fi network router with a RJ45 Ethernet
cable.
z
Wall mount holes – Mount
soun
ndbar on waall with screews(not included)
Sub
bwoofer
the subwoofer on
o or off.
Power – Switch
DC jack – Connect with power so
ource.
Pairing bu
utton – Activvate soundb
bar and sub
bwoofer pairing mode.
Remote Control
Power– Switch the soundbar on or to standby.
Wi‐Fi mode ‐ Select Wi‐Fi as an input source
Bluetooth mode ‐ Select Bluetooth as an input source
SOURCE – Select an input source for the soundbar.
VOL+ / VOL‐ ‐ Increase or decrease soundbar volume
Sub LV‐ / Sub LV+ ‐ Increase or decrease subwoofer volume
Game / Movie / Music – Use pre‐installed sound effect
Setup IMMERSE
The IMMERSE sound bar transmits sound signal from audio source to the subwoofer
by 2.4GHz wireless technology for reliable connection.
Connect Soundbar to Subwoofer
When the soundbar and subwoofer are connected to power source and powered on,
they connect automatically and the LED on subwoofer turns green.
If the connection between the subwoofer and the sound bar is lost …
1. Connect soundbar and subwoofer to power source.
2. Switch on the power of soundbar and subwoofer
3. Press the pairing button on the subwoofer
4. Press the “SUB” button on the soundbar touch panel or press the “SUB” button
on the remote control.
5.
6.
The SUB LED on soundbar and the LED on subwoofer are flashing which indicate
that they are establishing a connection.
The LED on soundbar stops flashing and the LED on subwoofer turns to solid
green when the connection is established.
Placement
IMMERSE offer 2 placement options of sounbbar to fit for different placements. For
better sound experience, the soundbar should be placed at or close to ear level.
Option 1: Tabletop
Comes with rubber foot at the bottom of IMMERSE, place the IMMERSE soundbar on
flat surface horizontally with the iui DESIGN logo facing out.
Option 2: Wall Mounting
Comes with screw holes at the back of the soundbar, follow the below steps to
mount it on wall.
1. Prepare screws (not supplied) that are suitable for the holes on the back of the
sound bar.
2. Fasten the screws to the wall. The screws should protrude 11 to 12mm.
3.
Hang the sound bar on to the screws.
Subwoofer
The subwoofer should be placed flat surface, preferably on floor. For stable
connection with the soundbar, place it within 3 meters or 9 feet from the soundbar.
Connect to TV
After you finish setting up the IMMERSE system, it can connect to a TV using analog
or optical audio input.
Connect the soundbar and TV with a RCA cable / a digital optical cable as shown
below.
If you connect using a RCA cable, select “ANALOG” as the audio source.
If you connect using a digital optical cable, select “OPTICAL” as the audio source.
Connect to DVD
After you finish setting up the IMMERSE system, it can connect to a DVD player using
analog, optical or coaxial audio input.
Connect the soundbar and the DVD player with a RCA cable / a digital optical cable /
a coaxial cable.
If you connect using a RCA cable, select “ANALOG” as the audio source.
If you connect using a digital optical cable, select “OPTICAL” as the audio source.
If you connect using a coaxial cable, select “COAXIAL” as the audio source.
Connect to other devices
After you finish setting up the IMMERSE system, it can connect to other devices, such
as smartphones, tablets, PCs, video game consoles, etc. using the following
connection options.
Wireless:
‐ Wi‐Fi
‐ Bluetooth
Wired
‐ Ethernet
‐ Aux‐in
‐ Analog
‐ Optical
‐ Coaxial
Wi‐Fi ‐ Connect to other devices
After you finish setting up the IMMERSE system, it can stream music wirelessly from
a digital music source through Wi‐Fi connection.
Before Setup
Please make sure your device is connected to the same Wi‐Fi network where
IMMERSE will be located. Otherwise, an error message will appear after entering
password as the app cannot detect IMMERSE in the current Wi‐Fi network.
Setup for Android / iOS user
1.
Download the free iui DESIGN Wi‐Fi Audio App from Google Play or App Store.
2.
Select “WIFI” as the audio source.
3.
Launch the app on your device. Press “Add Speaker” button to start the setup
procedure.
4.
Open the Wi‐Fi setting page on your device. Turn on the Wi‐Fi feature and select
“IMMERSExxxx”* from the list of available wireless networks*.
5.
Go back to the app and select your Wi‐Fi network inside the app.
6.
Enter password for your Wi‐Fi network you chose#. The LED indicator turns to
solid green.
7.
Rename IMMERSE and tap “Save” the confirm.
* If the IMMERSE could not be found in the list, follow the section “Reset Wi‐Fi
Connection” to reset the speaker to factory default and try again.
# In case of incorrect password or failed connection, follow the section “Reset
Wi‐Fi Connection” to reset the speaker to factory default and start the setup
procedure again.
Setup for PC / Mac user
1.
Select “WIFI” as the audio source.
2.
Connect IMMERSE to your PC / Mac using Wi‐Fi / RJ45 Ethernet cable.
A. Use an Ethernet cable to connect IMMERSE and your device. It takes
approximately 30 seconds to establish connection with IMMERSE. The LED
indicator will turn to solid amber once the connection is completed.
B.
Search and connect “IMMERSExxxx” in Wi‐Fi setting page*. The LED
indicator will turn to solid purple once the connection is completed.
3.
Browse the below link on your device to enter the setup page:
http://192.168.6.1/
4.
Select “Connect to Home” > “Wireless” in the setup page.
5.
Select your Wi‐Fi network.
6.
Enter password for your Wi‐Fi network you chose and Click “Join”.
7.
Click “Done” and remove the Ethernet cable if you use it for setup#.
* If the IMMERSE could not be found in the list, follow the section “Reset Wi‐Fi
Connection” to reset the speaker to factory default and try again.
# In case of incorrect password or failed connection, follow the section “Reset Wi‐Fi
Connection” to reset the speaker to factory default and start the setup procedure
again.
Streaming Music via Wi‐Fi Connection
For Android User
You should download a DLNA compatible player for streaming music. Select
IMMERSE (which may appear with the name you assigned) as your audio output
device in the music player. Different players may have different setups, please refer
to those corresponding user guides for detail.
For iOS user
You can stream music to IMMERSE via AirPlay:
1. Launch your music player
2. Tap on AirPlay
3. Choose “IMMERSE”
(If you renamed it, it will appear with the name you assigned)
For PC User
Windows Media Player 11 and above can be used to stream music to IMMERSE
through "Play To" feature. Use "Play To" on your music library from Windows Media
Player. For detail instruction for "Play To" feature, please consult the user manual for
your specific device.
For Mac User
You can stream music to IMMERSE via iTunes:
1. Launch iTunes
2. Click AirPlay
3. Choose “IMMERSE”
(If you renamed it, it will appear with the name you assigned)
* Please make sure your device is connected to the same Wi‐Fi network as
IMMERSE is located.
Advanced Setting
Using the iui DESIGN Wi‐Fi Audio App, you can control the advanced setting of
IMMERSE and other iui DESIGN Wi‐Fi speakers, including “Rename Your Speaker”,
“Multi‐Room”, “Audio Channel” and “Firmware Update”.
For multi‐room setting, see the section “Multi‐Room” for detailed instructions.
For firmware update, see the section “Firmware Update” for detailed instructions.
Reset Wi‐Fi Connection
If you wish to connect IMMERSE to another Wi‐Fi network or you could not find
IMMERSE in the list of available wireless networks in Wi‐Fi setting page, you need to
reset the Wi‐Fi connection. After restoring the factory setting, the name of speaker
will be set as “IMMERSExxxx”.
To reset the Wi‐Fi network, follow the below instructions:
1.
Connect IMMERSE to power source. Select “WIFI” as the audio source.
2.
Press and hold MFB+Volume Up + Volume Down keys for 4 seconds. The LED
indicator will flash red 4 times to indicate that the factory reset is done.
* The Factory Reset only applies to Wi‐Fi mode with no 3.5mm line‐in connection.
If you want to reset to the factory default, please disconnect the 3.5mm audio line in
cable.
Bluetooth ‐ Connect to other devices
After you finish setting up the IMMERSE system, it can stream music wirelessly from
a Bluetooth enabled device by setting or NFC (for NFC enabled devices only).
By Setting ‐ Bluetooth Connection
1. Select “BT” as the audio source.
2. Press “Bluetooth” button on remote control to activate pairing mode. Or, touch
and hold the MBF button on the soundbar touch panel
3. Turn on the Bluetooth feature on your device
4. Search “IMMERSE” and select.
5. Confirm pairing and the BT LED indicator lights up.
By NFC ‐ Bluetooth Connection ‐ for NFC enabled device only
1. Select “BT” as the audio source.
2. Turn on the NFC feature on your device
3. Tap on the NFC sensor for pairing.
4.
Confirm pairing and the BT LED indicator lights up.
Ethernet ‐ Connect to other devices
After you finish setting up the IMMERSE system, it can stream music wirelessly from
a digital music source through Wi‐Fi connection while the IMMERSE system is
physically connected with the Wi‐Fi router.
Before Setup
Please prepare a RJ45 Ethernet cable and a PC / Mac which has Wi‐Fi feature for
setup.
Setup
1. Select “LAN” as the audio source.
2.
Search and connect“IMMERSExxxx” in Wi‐Fi setting page*. The LED indicator
will turn to solid purple once the connection is completed.
3.
Browse the below link on your device to enter the setup page:
http://192.168.6.1/
4.
Select “Connect to Home” > “LAN” in the setup page.
5.
Click “Join”. Use an Ethernet cable to connect the soundbar and your Wi‐Fi
router.
6.
Click “Done”. The Ethernet LED indicator lights up once the connection is
completed.
Streaming Music via Wi‐Fi Connection
See the section “Streaming Music via Wi‐Fi Connection” under “Wi‐Fi – Connect to
other devices” for detailed instructions.
Advanced Setting
Using the iui DESIGN Wi‐Fi Audio App, you can control the advanced setting of
IMMERSE and other iui DESIGN Wi‐Fi speakers, including “Rename Your Speaker”,
“Multi‐Room”, “Audio Channel” and “Firmware Update”.
For multi‐room setting, see the section “Multi‐Room” for detailed instructions.
For firmware update, see the section “Firmware Update” for detailed instructions.
Aux‐in / Analog / Optical / Coaxial ‐ Connect to other devices
After you finish setting up the IMMERSE system, it can connect to an audio source
using aux‐in, analog, optical or coaxial audio input.
Connect the soundbar and the audio source with a 3.5mm audio line‐in cable / a RCA
cable / a digital optical cable / a coaxial cable as shown below.
If you connect using a 3.5mm audio line‐in cable, select “AUX IN” as the audio
source.
If you connect using a RCA cable, select “ANALOG” as the audio source.
If you connect using a digital optical cable, select “OPTICAL” as the audio source.
If you connect using a coaxial cable, select “COAXIAL” as the audio source
Multi‐Room
“Multi‐Room” allows grouping IMMERSE and other iui DESIGN Wi‐Fi speakers to play
together from the same music source. This feature only can be used in Wi‐Fi or
Ethernet connection and with iui DESIGN Wi‐Fi Audio App,
In the iui DESIGN Wi‐Fi Audio App, follow the below steps for multi‐room setup
Slide the button to group the speakers.
Stream music using Wi‐Fi connection.
* For most of the devices, it can connect reliably up to 3 speakers
* Due to limitation of iPhone, multi‐room is not stable for iPhone users.
Sound Effect Mode
There are 3 pre‐set sound effect modes in IMMERSE: Music mode, Movie mode and
Game mode. Different modes have different audio equalizer setting. You can choose
the mode that fits your usage.
Firmware Update
“Firmware Update” allows updating the firmware of IMMERSE maintain the best
product performance. It is strongly recommended that you always update your
firmware, and regularly check to see if an update is available.
For Android / iOS User
In the iui DESIGN app, the sign means there is update available.
Tap “ “.
Tap on the speaker you wish to update. Press “ “ button.
For PC User
1.
Connect your PC to the Wi‐Fi network where IMMERSE is located.
2.
3.
Open “Your Neighborhood Network”.
Double click EVERYWHERE to enter setup page.
4.
5.
6.
7.
Click
Click
Click
Click
“Others…”.
“Firmware Upgrade”.
“Check Update”.
“Update” if there is available update.
For Mac User
1. Connect your Mac to the Wi‐Fi network where IMMERSE is located.
2. Open “Safari”.
3. Select “Preferences…” in Safari toolbar.
4. Click “Advanced” and check the box for “Include Bonjour in the Favorites bar”.
5. Select “Bonjour > Webpages > IMMERSE” to enter setup page.
6. Click “Others… ”.
7. Click “Firmware Upgrade”.
8. Click “Check Update”.
9. Click “Update” if there is available update.
*Please keep stable network and power connection during firmware upgrade.
Troubleshooting
TBA

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2015:07:10 16:18:09+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2015:07:10 16:18:09+08:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : Microsoft Word - UD-1404S User manual
Document ID                     : uuid:d1aaad18-edc3-49bb-b6c8-54d8766a3449
Instance ID                     : uuid:f4adda2c-1fd2-4df3-9d8b-db88d757afa6
Page Count                      : 28
Author                          : Administrator
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NKTUD-1404S

Navigation menu