Pmi Piranha Evo Users Manual

: Pmi Pmi-Piranha-Evo-Users-Manual-804591 pmi-piranha-evo-users-manual-804591 pmi pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

INSTRUCTIONS FOR USE
The EVO grip frame is capable of high rates of fire and an agitating hopper such as a VL Revolution,
Halo, or Evolution 2 is recommended for better performance.
The EVO comes with a 9 volt rechargeable battery. You must charge it for a full 22 hours before initial use since the it does not come fully
charged. For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if your rechargeable
battery is dead or if you want to play with the frame right away. You will need to remove the right grip panel when you need to replace it.
EVO BATTERY:

WARNING: PMI RECOMMENDS USING THE 9V RECHARGEABLE BATTERY PROVIDED FOR OPTIMAL PERFORMANCE. DO NOT
USE THE BATTERY CHARGER WHEN USING ANY NON-RECHARGEABLE BATTERY.
SAFETY: Read your instruction manual and follow all the rules of marker safety. When you turn the marker on by holding the on/off button for three
seconds, it automatically goes into "safe mode." To turn the safety off, press the on/off button once lightly. The red on/off
Flush Cocking Rod
indicator will turn on and the marker is now ready to fire.
Electronic Anti-Chop Eye

PMI High Performance Rifled Barrel

Locking
Velocity Thumb
Adjuster

On/Off Button

To turn the marker back on safety,
press the on/off button once and the red on/off
indicator will turn off. To turn the marker off hold the on/off button
for three seconds while it is in safe mode. The frame should be left off
when not using the marker or you will drain the battery.
Low Pressure
Gauge
ON/OFF BUTTON: The on/off is the silver button located on the
left hand side of the gripframe. Push it once and hold it in for three full
seconds to turn your Evo LCD on. The LCD will turn on, but the marker
is in "safe mode." Press the on/off button again and the safety will
Adjustable
turn off. The red on/off indicator will then light up.

Sear Release
LCD
(see below)
On/Off Indicator
Charge Port

DSR Regulator

The Evo must be in "safe mode" to change the timer settings. Press button B on the right hand side once to change settings. Once
Adjustable Drop Forward
10º Bottom Line
the numbers are blinking use button A to increase timer clock by one minute
Adapter
increments. Press button B once when the countdown time is set and the
numbers will stop blinking. To start the timer, turn the safety
SEAR RELEASE SLIDE: The sear release slide is located on the left hand
off and fire the marker once.
side of the EVO grip frame. To reinstall the bolt/block/hammer assembly, push
the sear release slide up before the hammer comes in contact with the sear.
ODOMETER: The Evo must be in "safe mode" to view the odometer.
That will allow the bolt/block/hammer assembly to slide easily into the marker.
Press the A button to view the odometer.
TIMER:

LCD DISPLAY

The regulator pressure can be changed with a 1/8” allen
wrench. Screwing the adjustment screw in will lower the pressure. The regulator
should be set near 300 psi to get 300 fps. Lower regulator pressure will lower
velocity, but if the pressure gets too low, the marker might not recock.
REG PRESSURE:

00 00
Counter/Timer

Eye
Indicator

WARNING: Never use water to clean the marker, or
you run the risk of damaging the electronic trigger frame.

When the ACE is activated, it will only allow you to fire when there is a paintball in the chamber. When the
ACE is off, the rate of fire defaults to a slower setting so you won't chop paint. However, this means you will not be able to dry fire the marker quickly. To
turn the ACE on or off, press button B on the right hand side of the frame while the marker is ready to fire. The Eye logo on the LCD will only appear while
the ACE is turned on.
ELECTRONIC ANTI-CHOP EYE (ACE):

1.
2.
3.
3B.
3C.
3D.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
25A.
26.

Vertical Feed Receiver–Gold Fade
Barrel–Gold
Ram Air Chamber–Gold
Ram Air Spring
Ram Air Piston
Piston O-Ring
Field Strip Pin Assembly
Valve Body
Valve Cup Seal Assembly
Vertical Top Tube–Gold
Valve Guide
Valve Spring
Grey Venturi Bolt
Rear Block w/ Cushion
Flush Cocking Rod
Hammer Assembly
Hammer Spring
ASA O-Ring
Spring Guide
Vertical ASA–Gold
Left Eye Cover
Ball Detents
LCD Gripframe Assembly
Sear Release Slide
LCD Grips
Right Eye Cover
Thumb Adjust Velocity Screw
Velocity Lock Screw
Valve Set Screw

71711
71717
71546
71599
71579
10608
10021
71663
10127
71516
10520
71597
71704
71661
10201
10024
71598
10608
10301
71527
71701
10160
71720
71585
71707
71700
10482
42029
10514

27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
37.
37.
37.
38.
39.
41.
42.
43.
44.
45.
50.
51.
52.
53.
54.
55.
56.
57.

ASA Screw
Ball Detent/Eye Cover Screws
Rear Trigger Frame Screw
Grip Screws
Front Trigger Frame Screw
Bolt Pin
Velocity Screw O-Ring
Rear Block O-Rings
Blue Hammer O-Ring
Screen Filter
Bolt O-Rings
Valve O-Rings
Ram Air Chamber O-Ring
Regulator O-Ring
Trigger Assembly
Barrel O-Ring
3.75” Hose
Bottom Line SS Screws
10˚ Bottom Line Adapter–Charcoal
Sear
90° Elbow
Flush Cocking Guide O-Ring
C-Clip
Retaining Washer
Flush Spring
Drop Forward–Charcoal
Sear Spring
Trigger/Sear Pin
Sear Spring Pin

71580
10782
71583
71708
71582
10291
10460
10260
10129
71667
41010
41010
41010
41010
71586
10161
47021
42016
71646
71591
47000
10212
10207
10206
10203
71656
71590
71588
71589

58.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
79.
80.
81.
82.
83.
84.
85.
86.
87.
88.
89.
90.
91.
92.

Disassembly of electronic trigger frame will void warranty.

Trigger Spring
Low Pressure Gauge
NGO Top
Reg Seat Seal
Poppet O-Ring (013-70)
Poppet
Reg Seat Base O-Ring (006-70U)
DSR Reg Spring
Reg Seat Base
Reg Body Mid (black)
Bottom Swivel (black)
Bottom Bolt O-Ring (012-70)
Bottom Bolt
Adjusting Screw
Adjusting Screw O-Ring
DSR 10-32 Plug
Seal Stop O-Ring (002-70)
Interior Bottom Bolt O-Ring (010-70)
Clear EVO Eye
Smoke EVO Eye
Board Screws
Board Cover
Upper EVO Board
LCD Board
LCD Board Screws
8.4 Volt Battery
Charge Port Cover

71587
46090
41600
41517
57976
41509
10162
41510
41505
41601
41602
18085
41503
41504
57607
41506
57631
57645
71702
71703
71592
71593
71706
71705
71721
70181
71596



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2003:12:09 13:38:47
Producer                        : Acrobat Distiller 4.0 for Macintosh
Creator                         : QuarkXPressª: LaserWriter 8 8.7.1
Author                          : production assistant
Title                           : EVO
Modify Date                     : 2003:12:09 13:38:56-06:00
Page Count                      : 2

EXIF Metadata provided by EXIF.tools