Pmi Piranha Evo Users Manual
2015-09-01
: Pmi Pmi-Piranha-Evo-Users-Manual-804591 pmi-piranha-evo-users-manual-804591 pmi pdf
Open the PDF directly: View PDF .
Page Count: 2
The EVO grip frame is capable of high rates of fire and an agitating hopper such as a VL Revolution,
Halo, or Evolution 2 is recommended for better performance.
ELECTRONIC ANTI-CHOP EYE (ACE): When the ACE is activated, it will only allow you to fire when there is a paintball in the chamber. When the
ACE is off, the rate of fire defaults to a slower setting so you won't chop paint. However, this means you will not be able to dry fire the marker quickly. To
turn the ACE on or off, press button B on the right hand side of the frame while the marker is ready to fire. The Eye logo on the LCD will only appear while
the ACE is turned on.
SEAR RELEASE SLIDE:The sear release slide is located on the left hand
side of the EVO grip frame. To reinstall the bolt/block/hammer assembly, push
the sear release slide up before the hammer comes in contact with the sear.
That will allow the bolt/block/hammer assembly to slide easily into the marker.
REG PRESSURE: The regulator pressure can be changed with a 1/8” allen
wrench. Screwing the adjustment screw in will lower the pressure. The regulator
should be set near 300 psi to get 300 fps. Lower regulator pressure will lower
velocity, but if the pressure gets too low, the marker might not recock.
INSTRUCTIONS FOR USE
ON/OFF BUTTON: The on/off is the silver button located on the
left hand side of the gripframe. Push it once and hold it in for three full
seconds to turn your Evo LCD on. The LCD will turn on, but the marker
is in "safe mode." Press the on/off button again and the safety will
turn off. The red on/off indicator will then light up.
TIMER: The Evo must be in "safe mode" to change the timer set-
tings. Press button B on the right hand side once to change settings. Once
the numbers are blinking use button A to increase timer clock by one minute
increments. Press button B once when the countdown time is set and the
numbers will stop blinking. To start the timer, turn the safety
off and fire the marker once.
ODOMETER: The Evo must be in "safe mode" to view the odometer.
Press the A button to view the odometer.
SAFETY: Read your instruction manual and follow all the rules of marker safety. When you turn the marker on by holding the on/off button for three
seconds, it automatically goes into "safe mode." To turn the safety off, press the on/off button once lightly. The red on/off
indicator will turn on and the marker is now ready to fire.
To turn the marker back on safety,
press the on/off button once and the red on/off
indicator will turn off. To turn the marker off hold the on/off button
for three seconds while it is in safe mode. The frame should be left off
when not using the marker or you will drain the battery.
WARNING: Never use water to clean the marker, or
you run the risk of damaging the electronic trigger frame.
00 00
Eye
Indicator
Counter/Timer
LCD DISPLAY
Flush Cocking Rod
Locking
Velocity Thumb
Adjuster
On/Off Button
LCD
(see below)
Sear Release
Charge Port
Adjustable
DSR Regulator
Adjustable Drop Forward
Electronic Anti-Chop Eye
PMI High Performance Rifled Barrel
10º Bottom Line
Adapter
Low Pressure
Gauge
EVO BATTERY: The EVO comes with a 9 volt rechargeable battery. You must charge it for a full 22 hours before initial use since the it does not come fully
charged. For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if your rechargeable
battery is dead or if you want to play with the frame right away. You will need to remove the right grip panel when you need to replace it.
On/Off Indicator
WARNING: PMI RECOMMENDS USING THE 9V RECHARGEABLE BATTERY PROVIDED FOR OPTIMAL PERFORMANCE. DO NOT
USE THE BATTERY CHARGER WHEN USING ANY NON-RECHARGEABLE BATTERY.
Disassembly of electronic trigger frame will void warranty.
1. Vertical Feed Receiver–Gold Fade 71711
2. Barrel–Gold 71717
3. Ram Air Chamber–Gold 71546
3B. Ram Air Spring 71599
3C. Ram Air Piston 71579
3D. Piston O-Ring 10608
5. Field Strip Pin Assembly 10021
6. Valve Body 71663
7. Valve Cup Seal Assembly 10127
8. Vertical Top Tube–Gold 71516
9. Valve Guide 10520
10. Valve Spring 71597
11. Grey Venturi Bolt 71704
12. Rear Block w/ Cushion 71661
13. Flush Cocking Rod 10201
14. Hammer Assembly 10024
15. Hammer Spring 71598
16. ASA O-Ring 10608
17. Spring Guide 10301
18. Vertical ASA–Gold 71527
19. Left Eye Cover 71701
20. Ball Detents 10160
21. LCD Gripframe Assembly 71720
22. Sear Release Slide 71585
23. LCD Grips 71707
24. Right Eye Cover 71700
25. Thumb Adjust Velocity Screw 10482
25A. Velocity Lock Screw 42029
26. Valve Set Screw 10514
27. ASA Screw 71580
28. Ball Detent/Eye Cover Screws 10782
29. Rear Trigger Frame Screw 71583
30. Grip Screws 71708
31. Front Trigger Frame Screw 71582
32. Bolt Pin 10291
33. Velocity Screw O-Ring 10460
34. Rear Block O-Rings 10260
35. Blue Hammer O-Ring 10129
36. Screen Filter 71667
37. Bolt O-Rings 41010
37. Valve O-Rings 41010
37. Ram Air Chamber O-Ring 41010
37. Regulator O-Ring 41010
38. Trigger Assembly 71586
39. Barrel O-Ring 10161
41. 3.75” Hose 47021
42. Bottom Line SS Screws 42016
43. 10˚ Bottom Line Adapter–Charcoal 71646
44. Sear 71591
45. 90° Elbow 47000
50. Flush Cocking Guide O-Ring 10212
51. C-Clip 10207
52. Retaining Washer 10206
53. Flush Spring 10203
54. Drop Forward–Charcoal 71656
55. Sear Spring 71590
56. Trigger/Sear Pin 71588
57. Sear Spring Pin 71589
58. Trigger Spring 71587
67. Low Pressure Gauge 46090
68. NGO Top 41600
69. Reg Seat Seal 41517
70. Poppet O-Ring (013-70) 57976
71. Poppet 41509
72. Reg Seat Base O-Ring (006-70U) 10162
73. DSR Reg Spring 41510
74. Reg Seat Base 41505
75. Reg Body Mid (black) 41601
76. Bottom Swivel (black) 41602
77. Bottom Bolt O-Ring (012-70) 18085
78. Bottom Bolt 41503
79. Adjusting Screw 41504
80. Adjusting Screw O-Ring 57607
81. DSR 10-32 Plug 41506
82. Seal Stop O-Ring (002-70) 57631
83. Interior Bottom Bolt O-Ring (010-70) 57645
84. Clear EVO Eye 71702
85. Smoke EVO Eye 71703
86. Board Screws 71592
87. Board Cover 71593
88. Upper EVO Board 71706
89. LCD Board 71705
90. LCD Board Screws 71721
91. 8.4 Volt Battery 70181
92. Charge Port Cover 71596