Pontiac Automobile Parts Users Manual 250 4166

Automobile Parts to the manual af38e34c-c8fe-43ed-8272-1941eef59ef7

: Pontiac Pontiac-Automobile-Parts-Users-Manual-272652 pontiac-automobile-parts-users-manual-272652 pontiac pdf

Open the PDF directly: View PDF .
Page Count: 5

Download
Open PDF In Browser	View PDF

B.

REGULATOR

Note:

INSTALLATION

Remove left access panel above left rear
shock tower (note wing-type
nuts).

1. To form brackets for mounting regulator use
(Fig. 7) template. Refer to Owner's Manual on
Regulator Installation for bracket attachment
to regulator.
2. Trirn..il1sulation away from bracket
left shock tower.

on side of

3. Align regulator brackets with lower edge of
shock tower bracket. Mark and drill 2, 3/16"
holes. Install regulator using 1/4-14self-tapping
screws. Fig. 2
4. Route regulator cable under air cleaner. Follow
existing throttle cable to throttle as shown in
Fig. 3.
Form 2033

.rap

5. Attach~bead chain connector to existing
throttle as shown in Fig. 3.

D.

WIRING

HARNESS

1. Installation of the wiring harness requires a harness extension part #250-4166. This is due to the engine
distance from the fuse panel, brake light switch and control switch.

2

~

2. Remove Console
.a. Lift out ash trays. remove 2 -7 mm screws from each (under ash trays).
Note: This part of the console only needs to be lifted a few inches. Do not pullover

gear lever.

b. Loosen 2 -7 mm screws at the front of main console. Open glove box, remove 2 -7 mm screws. Lift out
console.
Note: Use caution upon removal not to damage wiring that is attached to the cigarette lighter.

Glove

Box

Loosen
two
7 mm Screws

./
?~

7

Removetwo
mm
.Screws

~

.,
~--"-~--~-:~:

Fig. 5
Harness
Extension

Ash Tray, one on each
side of gear lever

Remove

two

7 mm Screws

Connect white connector to 16' extension,
use red self-stripping connectors:

3

Fig.7

Fig.8

4

~

E.

VACUUM

TYPE

SYSTEM

1. To install vacuum type system on vehicle follow illustration as shown
below. Refer to Owner's Manual for remaining installation.

1st
-/HOle

ServoAssembly
/
~.

Shock
/TOWer

To Vacuum
Source ---c:

,~

'\ \-.'-

---11

/

~
~
3116" Hole (2)

R~:~~~~
~

SERVO
BRACKET
TEMPLATE

Servo
Bracket

3rd
Hole

F. ELECTRONIC

REGULATOR

AND

HARNESS

EXTENSION
1. Follow same procedure as mentioned in Section D, except
Electronic Regulator is mounted as shown in console.

Regulator

,

rC-

l!f

~

'I>
o

-

"

y'(

9132.. Hole

:'-'r
Harness
Extension

7/16"Hole

318" Hole

5



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Page Count                      : 5
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:2387539e-15fd-44bd-8e6a-8e170d7d3bf5
Producer                        : Hewlett-Packard Intelligent Scanning Technology.3
Modify Date                     : 2003:12:18 14:02:56-05:00
Create Date                     : 2000:03:16 12:02:24Z
Metadata Date                   : 2003:12:18 14:02:56-05:00
Document ID                     : uuid:bdfcc01c-63c2-451d-83c5-8cb289d57de4
Format                          : application/pdf
Title                           : 250-4166
Creator                         : ICP
Description                     : Supplement Installation Instructions for Pontiac Fiero
Author                          : ICP
Subject                         : Supplement Installation Instructions for Pontiac Fiero

EXIF Metadata provided by EXIF.tools