Porta Phone RF1900V1 DECT RF Module User Manual RFModuleUserManual

Porta Phone Company Inc DECT RF Module RFModuleUserManual

User Manual

Page 1 RF1G9V1 Module User Manual Introduction RF1G9V1 Module is a DECT (Digital Enhanced Cordless Telecommunications) compatibility products. To the quality of audio and to the safety offered from the digital technology, It’s offers manifold and useful features including Full duplex system. The module be application to cordless phone, walkie talkie and other data communications. Dimension Drawing Outside view
Page 2 Block Diagram Synch-Interface Pin1- syn_out Pin2- syn_en Pin3- syn_clk Pin4- syn_data Pin5- slot_ctrl Pin6- radio_en Pin7- trdata Pin8- vcc_dig Pin9- rstn Pin10,12-15,17,19-20,22-25,27,30-31.-GND Pin11- vccrf Pin16- vccPA Pin18- A_ctrl2 Pin21- ANT Pin26- A_ctrl1 Pin28- vccrf Pin29- bclk RX Part RC4,5,14,15 RL2,3,7,8 TX Part RC16,21,2427,28,63,64, RL4,5RU1 DE19RF19 RFIC Transceiver RD1 TX,RX Switch RF1G9 Pin1-7 Synch-Interface Syn_clk Syn_data EXT-CLK 13.824MHz
Page 3 Specification Standard DECT6.0 (Digital Enhanced Cordless Telecommunications) Frequency 1920 ~1930MHz (USA) Frequency 1880 ~1900MHz (EURO) Channel Separation 1.728 MHz Modulation type GFSK Transmission speed 1.152 Mbps (Baud rate) Duplexing Time Division Duplex (TDD) Speech encoding ADPCM / 32kbit/s RF Accessing Time Division Multiple Access (TDMA) TX Power Not more than 20dBm Channel 5(USA), 10(EURO) Coverage range 100m indoor; 400m in open space(PP to FP) Power Supply DC 3.3V/ 30-80mA Normal condition of use 0 O C to 40 O C Storage Temperature -10 O C to 60 O C LIMITED WARRANTY This limited warranty only applies to the use of this device with a communications service for which it is designed. This device alone does not provide the customer with any communications service and requires a separate subscription to a communications service from a service provider. Altering service provider-specific settings may void the warranty. This limited warranty does not warrant that the device will be free of any limitations of voice quality or service caused by (1) the services provided by the customer’s underlying communications service provider; or (2) interference from other radio frequencies or transmissions, static electricity, and other electronic devices. FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module The final end product must be labeled in a visible area with the following” Contains FCC ID:B4HRF1900V1 FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The module supports the highest gain of antenna is 2.0dBi when install to the end product.
Page 4 IC Warning: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Le présent appareil est conforme Après examen de ce matériel aux conformité ou aux limites d’intensité de champ RF, les utilisateurs peuvent sur l’exposition aux radiofréquences et la conformité and compliance d’acquérir les informations correspondantes. La distance minimale du corps à utiliser le dispositif est de 20cm. Assemble to main board The RF module can put on the main board by SMT or hand soldering. This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module The final end product must be labeled in a visible area with the following” limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This equipment complies with IC radiation exposureThe module supports the highest gain of antenna is 2.0dBi when install to the end product.contains IC:3064A-RF1900V1.

Navigation menu