Power Monitors E2003 Eagle Class PQ Wireless Power Monitor User Manual Eagle users manual 1203
Power Monitors, Inc. Eagle Class PQ Wireless Power Monitor Eagle users manual 1203
users manual
Eagle Class PQ Wireless™ Recorder User’s Manual Power Monitors Inc. 1661 Virginia Avenue Harrisonburg, VA 22802 USA http://www.powermonitors.com 1-800-296-4120 540-434-4120 Fax: 540-432-9430 Eagle Class PQ Wireless™ Digital Recorder Manual ©2003 Power Monitors Inc. All Rights Reserved Contents subject to change without notice. This version: November 2003 Corrections or ideas for this manual please e-mail: lbarker@powermonitors.com Eagle Class PQ Wireless™ Digital Recorder Manual Foreword We founded Power Monitors Inc. (PMI) to provide state-of-the art, easy-to-use, and affordable electronic test equipment to the power industry. Our products have been developed by working directly with electric utilities to determine their specific needs. These products are designed for only one purpose: to collect and assist in the analysis of field-recordable data for electric utilities. The Eagle Class Recorder™ were developed with your needs in mind. We created them to meet the needs of a large utility, and based their unique capabilities on our years of experience building versatile voltage recording and analysis equipment. Inside lightweight, weatherproof, rugged enclosures, state-of-the-art electronics measure and record true RMS voltage and current on four channel connections. The units require so little power; they operate on the voltage from one of the attached lines. There are no batteries to recharge prior to use. Each unit has been individually calibrated to ensure high accuracy and stability over a wide range of temperatures. PMI recorders remain the only products on the market that will allow both electronic “stripchart” recording and a number of specialized recording modes tailored to the power industry. The specialized reports are merged with unique data collection techniques to provide accurate information that is easy to understand. Features such as flicker monitoring, event recording, and min/max/Avg recording of both voltage and current make PMI recorders the ideal products for distribution monitoring. The Recorder features: • • • • • • • • • True RMS voltage and current measurement on each of four channels Programmable abnormal voltage recording On-site, real-time display of voltage, current and power via Palm PDA & PMIScan or PMIView Software Single-cycle response (16 msec) More than 122,000 samples per second 0-600 volt RMS operating range 0-10, 100, 500, 1000, and 5000 Amp current input ranges Up to 4,096K FLASH EPROM memory Memory capacity for more than one year of summary data, 500 event records, 500 records of significant change, 500 records of flicker data • Rugged, weatherproof enclosure NEMA 4X • All channels captured simultaneously in one cabinet Recorder/WinScan™ graphs and reports include: • Stripchart and histogram analysis for RMS voltage, RMS current, power factor, displacement power factor, real power, apparent power, reactive power, volt-amps, frequency, and phase angle • Power outage report • Abnormal voltage report • Current or voltage out of limits report • Significant change report • Event change report • Flicker report Because of these capabilities, the Eagle Class Recorder™ are the perfect instruments for analyzing and solving power quality and quantity problems. After looking through this manual and using your Recorder, please contact us with any questions about its operation, or with ideas for new features or products. We want you to be happy with this product, and we always appreciate any input that helps us develop products to meet your future needs. Thank you, Walter M. Curt Owner, Power Monitors Inc. Eagle Class PQ Wireless™ Digital Recorder Manual TABLE OF CONTENTS FOREWORD................................................................................................................................................3 1.1.1 Purpose ..........................................................................................................................................8 1.1.2 Manual Layout ..............................................................................................................................8 1.2 RECORDER DESCRIPTION...............................................................................................................8 1.2.1 General...........................................................................................................................................8 1.2.2 Available Models ...........................................................................................................................9 1.2.3 Inputs .............................................................................................................................................9 1.2.4 Instrument Size..............................................................................................................................9 1.2.5 System Description ........................................................................................................................9 1.2.6 Memory ........................................................................................................................................10 1.2.7 Clock ............................................................................................................................................10 1.2.8 Recorder Construction ................................................................................................................10 1.2.9 Communications..........................................................................................................................10 1.3 SUPPLIED EQUIPMENT ..................................................................................................................10 1.3.1 Equipment Listing .......................................................................................................................10 1.4 ACCESSORIES ..................................................................................................................................10 1.4.1 General.........................................................................................................................................10 1.4.3 Current Probe ..............................................................................................................................11 1.4.4 Adapters .......................................................................................................................................11 1.4.5 Cases ............................................................................................................................................11 1.4.6 Spare Parts List............................................................................................................................11 1.4.6 VOLTAGE CLIPS ................................................................................................................................11 1.5 SPECIFICATIONS.............................................................................................................................12 1.5.1 General.........................................................................................................................................12 SAFETY NOTICE .....................................................................................................................................13 CONNECTION INFORMATION CHAPTER 2 ....................................................................................14 2.1 INTRODUCTION ..............................................................................................................................14 2.1.1 General.........................................................................................................................................14 2.1.2 Manual Updates...........................................................................................................................14 2.2 EQUIPMENT HANDLING................................................................................................................14 2.2.1 Initial Inspection .........................................................................................................................14 2.2.2 Unpacking Procedure..................................................................................................................14 2.2.3 Equipment Return .......................................................................................................................14 2.2.4 Storage .........................................................................................................................................14 2.3 WIRING SPECIFICATIONS AND....................................................................................................15 PROCEDURES ........................................................................................................................................15 2.3.1 Power Requirements....................................................................................................................15 2.3.2 Installing the Recorder................................................................................................................16 2.3.3 Communications Port Connections ............................................................................................20 OPERATION CHAPTER 3 ......................................................................................................................21 3.1 INTRODUCTION ..............................................................................................................................21 Eagle Class PQ Wireless™ Digital Recorder Manual 3.1.1 General.........................................................................................................................................21 3.2 CONTROL AND PRESENTATION..................................................................................................21 3.2.1 General.........................................................................................................................................21 3.2.2 Operator Controls ........................................................................................................................21 3.2.3 Initialization.................................................................................................................................21 AN OUTLINE OF WINSCAN™ CHAPTER 4 ......................................................................................22 4.1 RETRIEVING DATA FROM THE RECORDER ..............................................................................22 APPENDIX 1: PC AND RECORDER CONFIGURATION FACTORY SETTINGS .......................23 APPENDIX 2: WARRANTY CLAUSE...................................................................................................25 APPENDIX 3: TROUBLESHOOTING ..................................................................................................26 APPENDIX 4: EAGLE CLASS RECORDER™ FORMULAS ............................................................27 APPENDIX 5: REGULATORY INFORMATION ................................................................................31 INDEX.........................................................................................................................................................32 Eagle Class PQ Wireless™ Digital Recorder Manual SAFETY NOTICE THIS SAFETY NOTICE HAS BEEN INCLUDED TO EMPHASIZE THE DANGER OF HAZARDOUS VOLTAGES ON THE INPUT CONNECTION LEADS OF YOUR INSTRUMENT. USE EXTREME CAUTION WHEN CONNECTING OR SERVICING YOUR INSTRUMENT. SIGNAL INPUTS WARNING USE EXTREME CAUTION WHEN WIRING SIGNAL INPUT CONNECTIONS. HAZARDOUS POTENTIALS MAY EXIST ON SIGNAL INPUT LEADS. THESE HAZARDOUS POTENTIALS MAY BE EXPOSED INSIDE THE INSTRUMENT CASE AND ON THE VOLTAGE CLIPS OF YOUR INSTRUMENT. ANY VOLTAGE POTENTIAL AT THE SIGNAL SOURCE WILL EXIST ON THE INSTRUMENT'S RESPECTIVE SIGNAL INPUT CABLE. SAFETY ISSUES PLEASE READ CAREFULLY BEFORE INSTALLING OR USING THE RECORDER. THE RECORDER CONTAINS DANGEROUS VOLTAGE LEVELS DURING OPERATION. DO NOT DISASSEMBLE THE RECORDER. THE RECORDER CONTAINS NO USER-SERVICEABLE PARTS INSIDE. THIS DEVICE IS MANUFACTURED FOR USE BY TRAINED AND QUALIFIED PERSONNEL ONLY. DO NOT INSTALL OR OPERATE WHILE IN CONTACT WITH STANDING WATER OR WET GROUND. WEAR PROTECTIVE GLOVES AND SAFETY GLASSES AT ALL TIMES DURING THE INSTALLATION, OPERATION AND REMOVAL OF THE RECORDER. DURING INSTALLATION, DISCONNECT POWER FROM ANY LINES TO WHICH THE RECORDER WILL BE ATTACHED. PMI CURRENT PROBES ARE MANUFACTURED WITH INTEGRAL LEADS AT THE CLAMP-ON PROBE END, PREVENTING ACCIDENTAL DISCONNECTION AND MAXIMIZING SAFETY. IN ADDITION, THE CURRENT PROBE ASSEMBLIES INCORPORATE A BUILT-IN VOLTAGE-LIMITING FEATURE. THIS LIMITS THE PROBE OUTPUT VOLTAGE TO ONLY A FEW VOLTS SHOULD THE PROBE BECOME DISCONNECTED FROM THE RECORDER WHILE STILL CLAMPED AROUND THE CURRENT-CARRYING CONDUCTOR. THIS FEATURE PREVENTS THE POSSIBILITY OF ELECTRIC SHOCK TO THE USER AT THE DISCONNECTED CONNECTOR END TERMINALS. PROBE CABLES WITH A WATERPROOF CONNECTOR THAT MATES WITH A WATERPROOF RECEPTACLE MOUNTED ON THE RECORDER HOUSING ARE ALSO PROVIDED. ALTHOUGH THE RECORDER HAS BEEN DESIGNED AND BUILT TO BE AS SAFE AS POSSIBLE, GREAT Eagle Class PQ Wireless™ Digital Recorder Manual CARE SHOULD BE EXERCISED AT ALL TIMES DURING OPERATION AND INSTALLATION. Eagle Class PQ Wireless™ Digital Recorder Manual GENERAL DESCRIPTION CHAPTER 1 1.1 GENERAL 1.1.1 Purpose This manual is a user reference guide for the Series Eagle Class Recorder™ (Figure 1-1). The manual provides detailed instructions for connection, operation, programming, and communications interface. 1.1.2 Manual Layout The layout of this Manual is by Chapters and numbered Paragraphs. A. Chapters Chapters within this manual are arranged in the following order: Chapter 1 - General Description Chapter 2 - Connection Information Chapter 3 - Operation Chapter 4 - Configuration Chapter 5 - Communications Interface B. Paragraphs Paragraphs are numbered sequentially with the first number corresponding to the Chapter number, the second number corresponding to the topic, and the third indicating number paragraph within that topic. Alpha characters indicate subparagraphs of the main paragraph. Figure 1-1: Eagle Class Recorder™ 1.2 RECORDER DESCRIPTION 1.2.1 General The Eagle Class Recorder™ are easy-to-use, true RMS, micro-computer-based voltage, amperage and power recording device that produce accurate readings and professional reports. These recorders can help you resolve customer voltage and power quality complaints, record flicker, conduct long-term voltage and current surveys, and detect voltage and current variations as brief as one cycle. The Recorders will not disrupt normal power supply; rather, it uses a minimal amount of voltage from one of the lines it is monitoring. Each Recorder gathers and stores stripchart data, recording the average, minimum and maximum readings for a selected interval with one-cycle resolution. Even events lasting less than one cycle are revealed in WinScan™ reports if the Recorder is configured to capture the information. The Recorder also calculates derivative power measurements such as power factor, phase angle, reactive power, and others. Installing the Recorder is relatively simple, although using the unit requires the same attention to safety as working with any other high-voltage device. Once the unit has been installed and the data you need have been recorded, the data can be downloaded using either serial cable or Bluetooth wireless technology. Real-time data can be checked using a Palm® operating system PDA. Please refer to the PalmView manual for further information. You can then view and analyze the data using the WinScan™ software. With the software you can create an array of graphs and reports, each of which provides you with useful, clearly presented power data. Eagle Class PQ Wireless™ Digital Recorder Manual 1.2.2 Available Models There are several models of the Eagle Class Recorder™ that can be provided. The label on the front cover will designate the model of the unit. The recorder models available and their corresponding codes are: 220 – 2 Channel (two voltage and two current) 330 – 3 Channel (three voltage and three current) 440- 4 Channel (four voltage and four current) Figure 1-2: Recorder Label 1.2.3 Inputs Direct hookups are fed into 2,3, or 4 voltage, 0-600vac, and 4 current inputs. The amount of current that can be monitored is dependant on the current transducer being used. Up two eight direct inputs are available to be recorded and used with reports and strip charts. To record an input, the input must be selected as a strip chart in WinScan™. 1.2.4 Instrument Size The Recorder is contained in a standard 5-3/8 inch (136.5 mm) long x 2-3/8 wide (60.3 mm) high x 1-3/16 inch (30mm) high NEMA 4x sealed box. 1.2.5 System Description The Recorder is a system designed to measure and record AC Power parameters using state of the art digital technology. Signal inputs from AC power connections are monitored by the system. No pen, ink or paper are required. The unit can also be used with PalmView software running on a Palm® Personal Digital Assistant (PDA) for real time viewing of waveforms, harmonic bar graphs, vectors, as well as numeric values. A. Day-To-Day Use Day-to-day operating measurements are stored and recalled instantly. Up to two MB of standard internal memory allows data to be efficiently and economically stored and retrieved. B. Configuration WinScan™ software allows the user to program the unit quickly and efficiently using an Windows operating system PC. Programming can also be done using PalmScan Software running on a Palm® PDA. It’s graphical touch screen interface provides straight forward, user friendly configuration. Strip charts, Event parameters, and Flicker parameters can be easily programmed. Other parameters such as Scales, CT and PT ratios, and engineering units are also easy to program. C. Applications A Recorder may be configured by you to record and monitor almost any voltage and current configuration. Typical measurement applications include, but are not limited to: • Voltage Levels • Current Levels • Power Factor • Harmonics to the 51st • Phase Rotation • Flicker • Power Levels Eagle Class PQ Wireless™ Digital Recorder Manual D. System Technology This power Recorder is a state of the art system, designed around a microprocessor, with an executable program stored in memory. The memory is used for data and setup storage. Bluetooth Wireless technology is also incorporated to allow users access to data without an actual physical connection. 1.2.6 Memory Electrically Erasable Programmable Read Only Memory (EEPROM) eliminates the need for a battery back-up. Programming is stored in EEPROM. In the event of a power loss or system reset, the programming will be protected. 1.2.7 Clock The Time-of-Day clock will be maintained indefinitely after loss of line power by an internal NiMH battery. 1.2.8 Recorder Construction The Power Recorder features modular construction. All printed circuits boards are sealed for electrical isolation and protection from the elements. Servicing should only be done by an authorized service center of PMI. The PC boards are conformal coated and high voltage is present, servicing by unauthorized personnel can result in product or bodily damage. 1.2.9 Communications The standard RS232 port allows you to plug the Recorder into your computer and download the data from memory. An AC Adapter is also supplied that you can plug into the 9 pin D shell that will power the unit for programming or downloads. This eliminates the need to have AC voltage supplied directly to the voltage leads. 1.3 SUPPLIED EQUIPMENT 1.3.1 Equipment Listing Figure 1-3: Serial Cable The following items are supplied with your Recorder: • the Eagle Class Recorder™ • CD Containing • WinScan™ • This manual • a WinScan™ Manual • Sample files • a serial communications cable • a 12-volt power adapter wall transformer and cord. • Voltage leads and probes If any of these items are missing, call PMI immediately. Current probes are an accessory and should be ordered as a separate line item. 1.4 ACCESSORIES 1.4.1 General Additional functions and capabilities can be added to the Recorder as accessories. These options are briefly described in the following paragraphs. Eagle Class PQ Wireless™ Digital Recorder Manual 1.4.2 Current Clamps TLAR 10 Amp current clamps are available in sets of 2,3, or 4 clamps. 1.4.3 Current Probe Figure 1-4: TLAR Clamps PMI has a wide range of current probes (Flexible CTs) that range in circumference from 24 to 48 inches and have ranges of 100, 1000, and 5000 Amps. All our flexible current probes are powered from the unit itself so no external batteries are needed. See figure 1-5 1.4.4 Adapters If you have an older PMI unit we have a wide range of adapters available so you can use your existing serial cables with your new unit(s). 1.4.5 Cases PMI carries a wide selection of cases to carry your new or old unit, cables, CTs, and manuals all in the same container. See figure 1-6. Figure 1-5: Flex CTs 1.4.6 Spare Parts List Eagle Class Recorder™ ---------------------------------------------------Eagle Class Recorder™ Comm. Cable Voltage Leads BLK test lead, straight to Right Angle RED test lead, straight to Right Angle BLU test lead, straight to Right Angle YEL test lead, straight to Right Angle WHT test lead, straight to Right Angle Jaw Grip, 4mm 90506002000 30150021 30250022 30250023 30250024 30250025 30250026 Figure 1-6: Cases 1.4.6 Voltage Clips PMI carries a wide variety of voltage clips for your application. Figure 1-7: Voltage Clips Eagle Class PQ Wireless™ Digital Recorder Manual 1.5 SPECIFICATIONS 1.5.1 General The Eagle Class Recorder™ specifications are shown in Table 1-1. Table 1-1 Eagle Class Recorder™ Specifications Eagle Class Recorder™ Recorder Specifications Input AC Voltage 0 to 600 VAC AC Current 0 to 10, 100, 1000 or 5000 Amps Sample rate: samples per second 122,800 all channels 15,360 per channel (256/cycle) Channels 2, 3, or 4 voltage 2, 3, or 4 current Measured Qualities RMS Voltage (Volts) RMS Current (Amps) Real Power (Watts) Apparent Power (VA) Reactive Power (VAR) Phase Angle (Degrees) Power Factor (Watts/VA) Displacement PF (cos(phase angle)) Power Usage kWh, kVARh, kVAh Frequency Hz Note: All quantities are measured for each cycle. Accuracy/Resolution (-20°F to 135°F) Accuracy Percent of full scale Voltage 0.33 % (w/o probe) Current 1.0 % Power 1.0 % Phase Angle 1 degree Power Factor ±0.02 Displacement PF ±0.02 Resolution: Displayed/Internal Voltage 1 V / 0.1 V Current 0.1 A / 0.1 A on 10-amp (Displays 1 A on other scales) Power 10 W / 10 W VAR 10VAR/10VAR VA 10VA/10VA Phase Angle 1° / 1° Power Factor 0.01 / 0.01 Displacement PF 0.01 / 0.01 Power Usage 0.001 kWh/0.001 kWh Information Storage Memory RAM FLASH EPROM DSP Waveform RAM TOTAL MEMORY Waveform capture: 128K (battery-backed) 4MB up to 256K 2.2 million readings Triggered Capacity Summary data Over 1 year Event data 500 records Significant change data 1000 records Flicker data 1000 records Stripcharts 4 hours to over 1 yr. Voltage Current Power Factor Displacement PF Real Power Reactive Power Apparent Power Phase Angle Frequency Retention time > 5 years Communications Local Type Serial Cable Wireless Bluetooth Standards RS232 Compatible, Bluetooth Data rate 1,200 to 56 kbaud Stripchart settings 1 second to 4 hours Significant change 1V to 8 V, in 1V steps Flicker settings User-defined or standard Battery voltage check Automatic Power Requirements Recording load < 1.5 Watts Environmental Operating temperature -20°F to 135°F Shock 60Hz to 2KHz, acceleration 25G Vibration 10Hz to 60Hz, amplitude 1.8mm Physical Dimensions Size 5.375” x 2.375” x 1.188” Weight <1.0 lbs. Case NEMA 4X Power Fail Operation The device operates with no input voltage for more than 2 hours. This allows it to measure down to 0 volts on all channels during power outage periods. Harmonics (optional) Voltage Current Measures: Magnitude Phase THD Measures to the 51st Measures to the 51st Implementation of new developments and product improvements may result in specification changes in this document Eagle Class PQ Wireless ™ Digital Recorder Manual SAFETY NOTICE This Safety Notice has been included to emphasize the danger of hazardous voltages on the INPUT CONNECTION LEADS of your instrument. USE EXTREME CAUTION WHEN CONNECTING OR SERVICING your instrument. Please read the entire contents of the Installation and Wiring Chapter before attempting to connect or service your instrument. SIGNAL INPUTS WARNING Use extreme caution when wiring signal input connections. Hazardous potentials may exist on signal input terminals, which are floating, with respect to instrument ground. These hazardous potentials may be exposed inside the instrument case and on the Connectors of your instrument. Any voltage potential at the signal source will exist on the instrument's respective signal input cable. 13 Eagle Class PQ Wireless ™ Digital Recorder Manual Connection Information Chapter 2 2.1 INTRODUCTION 2.1.1 General This chapter provides information and procedures for connection of the Recorder. Included are handling procedures, installation and wiring specifications, and instructions for both standard and optional equipment. 2.1.2 Manual Updates This manual may periodically be up-dated with addendums that could affect the connection information contained in this section. Review each addendum, if any, in the front of this manual and note changes that pertain to this section. 2.2 EQUIPMENT HANDLING 2.2.1 Initial Inspection Exercise care when unpacking instruments from the shipping cartons. The instruments are packed in a shock-resistant foam retainer to prevent damage during normal transit. If damage to the shipping carton is evident, ask the carrier's representative to be present when the instrument is unpacked and refer to Limited Warranty Statement, Appendix A. 2.2.2 Unpacking Procedure Perform the following steps to unpack your Recorder. 1. Remove the foam retainer and instrument from the shipping carton. 2. Carefully remove the instrument from the foam retainer. A. Detected Damage If damage is detected after unpacking the instrument, re-pack the instrument and return it to the factory as described in the following paragraph. 2.2.3 Equipment Return Before returning a damaged or malfunctioning instrument to the factory for repairs, a Return Authorization Number must be obtained from the factory. A. Return Authorization and Required Information If the instrument is to be returned for repairs, refer to Appendix B, "Return Authorization", for complete instructions on returning instrumentation. 2.2.4 Storage For prolonged storage before installation, re-pack the Power Recorder in the shipping container. Cushion the Recorder with foam molding or equivalent and store in a cool, dry area. We do not recommend storage of the Recorder for more than one year. If longer storage time is required, contact the factory for additional storage information. See Table 2-1. 14 Eagle Class PQ Wireless ™ Digital Recorder Manual Table 2-1: Environmental Precautions ENVIRONMENTAL PRECAUTIONS For optimum performance, observe the following precautions when selecting a storing environment for the Recorder. • Avoid direct sunlight and high temperature. Operating temperature must be within -20°F to 135°F (-29 to 57°C). • Avoid sudden temperature swings of 10°C or more. • Avoid locations susceptible to vibration, shock, static electricity, high magnetic, electro-magnetic, or radiation fields. • Avoid extremely dusty, dirty, or corrosive gas environments. • Maintain adequate air circulation paths to ensure proper cooling of the unit. Ambient operating temperature should not exceed 135°F (57°C). Detailed Specifications are included in Chapter 1, Table 1-1,2,3. 2.3 WIRING SPECIFICATIONS AND PROCEDURES 2.3.1 Power Requirements The Recorder operates on voltages from 80 to 600Vac, 45-65 Hertz. A. Recorder Operating Power Connection Power connections to the Recorder are made by connecting the Phase A voltage signal input wiring to an appropriate signal of 80-600Vac. This will automatically charge the batteries (Batteries could take up to 14 hours to fully charge) and power up the Recorder. B. Batteries and power The Recorder, when installed, powers itself from the line voltage on Channel 1. It requires less than 1.5 watts. This means the Recorder does not contain large internal batteries that must be recharged or replaced; the Recorder can be retrieved from the field, downloaded, and reinstalled elsewhere minutes later. A small, AAA NiMH battery takes care of the Recorder’s minimal power needs during a power outage while the Recorder is in record mode. This battery recharges off Channel 1 and should be replaced every three years. In addition, a Li memory backup battery allows the Recorder to sit on a shelf for up to three years after being initialized and still be ready for installation. Its memory can also hold recorded data for up to three years. A 12-volt power adapter is provided to power the Recorder during downloads in the office or in the field if the Recorder has been disconnected from the line voltage. The AAA battery will run the unit for up to 2 hours if power is lost. WARNING 15 Eagle Class PQ Wireless ™ Digital Recorder Manual WHEN CONNECTING THE SIGNAL MEASURING LEADS, BE CAREFUL NOT TO TOUCH ANY OF THE CONNECTION POINTS. LETHAL VOLTAGE AND CURRENT CAN EXIST ON ANY INPUT LEAD OR CONNECTION POINT. 2.3.2 Installing the Recorder This chapter explains the physical installation of the Eagle Class Recorder™. Installing the Recorder is not difficult for a professional familiar with similar equipment, although the same care required when working with any high-voltage equipment must be taken to complete the job safely. Please take the time to read Safety Issues, page 6, before installing the Recorder. There are two things to connect when installing the Recorder: 1. The current probes, and 2. The alligator voltage clip leads. Installation of the current probes depends on whether your Recorder is equipped with these items. Please read through the next three sections before installing your Recorder. Disconnect the power from the lines you plan to monitor until the installation is complete. Also, connect channel 1 voltage last, as this will start the two minute countdown for recording. A. The current probes 1. CTs The optional TLAR current clamps connect to the nine pin connector on the side of the Recorder housing. The Recorder automatically detects the amperage rating of the clamp connected during the two-minute initialization countdown which starts when power is applied to the unit (see below). The Eagle Class Recorder™ Recorder can be equipped with current clamps rated for 10A (TLAR), or Flexible CTs that have multiple ranges of 100A, 1000 or 5000A. Once the desired clamps are properly connected to the Recorder, clamp around the line or bus you wish to monitor. The arrow on the body of the current clamps or probes must point toward the customer (away from the utility)—in the direction of the current. The current clamps measure amperage through induction. PMI recommends that current clamps be connected to the Recorder whenever they are attached to a power line. 2. Installation of Flexible CT Insert the connector of the Flex CT into the 9-pin connector on the side of the recorder. The cable branches to 2, 3 or 4 flexible clamps, each of which is snapped into a loop around each line to be monitored. The “smart box” midway on the cable senses the induced current and processes the information for measurement. The recorder’s current range can be set using WinScan or PMIScan. Remember, Safety is always our primary concern. C. The voltage clip leads The Recorder can monitor voltage on up to four channels. Alligator clip leads are provided for each channel. These leads are color-coded as follows: Table 2-2: Voltage leads color coding Channel Channel 1 Channel 2 Channel 3 Channel 4 Common Lead Black Red Blue Yellow White Phase Common 16 Eagle Class PQ Wireless ™ Digital Recorder Manual Attach the alligator clip leads to voltage lines in a pattern which will monitor the phases on which you wish to collect data. For information on several ways to monitor power, see the next section, Connecting to different types of services. The Recorder will borrow its power from the voltage on Channel 1. As soon as voltage is applied to the Channel 1 lead, the Recorder begins a two-minute countdown. During this countdown, the Recorder will sample the voltages on each channel in order to set the nominal voltage for the recording period. The Recorder also uses this time to detect which probes are connected to it—see the information on current probe connections above. While the countdown continues, you may adjust some Recorder settings. However, making a change to the Recorder settings will restart the countdown at two minutes. During the two-minute countdown, you may exchange one type of current clamp for another (on the Eagle Class Recorder™ only). However, if you change the probes, you must restart the two-minute initialization countdown by interrupting and then restoring power to the Recorder. If probes on an operating Recorder are exchanged with probes of a different type without reinitializing the Recorder, the unit will retain the setting of the first probes as the operating type. This may result in incorrect measurements. 1. Connecting to different types of services - When planning how to connect your Recorder, keep the following things in mind: • The banana jacks are color-coded by channel: black is Channel 1, red is Channel 2, blue is Channel 3, yellow is Channel 4, and white is common. • The unit is powered from the voltage between Channel 1, the black jack, and common, the white jack. For this reason, even if you are not connecting all the input wires, Black and White must be connected. • Be aware of the input voltage warning label on the Recorder, do not exceed the maximum input voltage. The limits are 600 volts RMS channel to channel or channel to common for the Eagle Class Recorder™. • You may use four-channel units to monitor five-channel systems; naturally, you will record data for only four of the channels. Conversely, you can use a four-channel unit to monitor a single-phase system: either unplug the unused leads, connect them in parallel so that all channels are recording the same information, or clip together to avoid noise readings. Again, the Channel 1 leads must be connected in order to power the unit.. Below are diagrams showing several basic circuits and possible ways to connect them: To connect a Recorder to monitor a delta service, connect one of the clips leads for three channels to both corners of the phase. Clip lead for Channel 1 (black) will be connected to one corner (A). Clip the White lead to the next corner (B), and clip the blue lead to the third corner (C). Figure 2-1: 3 Wire Delta 17 Eagle Class PQ Wireless ™ Digital Recorder Manual Figure 2-2: 4 Wire Delta You can connect the clip leads phase-to-phase on a Wye service in the same manner you would when monitoring a delta service. Figure 2-3: 3 wire wye phase to phase 18 Eagle Class PQ Wireless ™ Digital Recorder Manual Figure 2-4: 4 wire wye You can also connect the unit to monitor phase-to-neutral references by connecting one lead (the hot side) for each channel to the respective phase in the circuit, and connect the white lead (common) to the neutral. In the diagram, Channel 1 is represented by the black lead, Channel 2 (red) , and Channel 3 (blue). 19 Eagle Class PQ Wireless ™ Digital Recorder Manual Figure 2-5: Two phase three wire Figure 2-6: 2.5 Element Z-coil 2.3.3 Communications Port Connections A. General Designed into the Recorder is a Communications Port. The standard interface cable is an RS232 Serial type used to interface with a remote terminal or computer. The Communications Port allows you to access and manipulate the recorded information on the Recorder. Figure 2-7: Serial Connection B. RS232 Serial Cable The RS232 Serial Cable is configured and wired to conform to the industry standard RS232 connection. Connect the 6-pin connector of the comm. cable to your Recorder and the DB-9 (RS232) end of the cable to your computer serial port If the Recorder’s channel 1 voltage leads are not connected to >80Vac, connect the AC adapter provided to the power jack on the 9 pin D shell as shown in figure 2-7. Then plug the adapter into a 120VAC outlet. You can now use WinScan™ to download and/or set up the unit to record. Please refer to the WinScan™ manual for instructions. 20 Eagle Class PQ Wireless ™ Digital Recorder Manual Operation Chapter 3 3.1 INTRODUCTION 3.1.1 General This chapter contains information concerning system operation 3.2 CONTROL AND PRESENTATION 3.2.1 General The following paragraphs are intended to familiarize you with the front panel controls and commands along with any other day-to- day operating controls. The Recorder presents information through the display and the WinScan™ program. 3.2.2 Operator Controls All controls are via the WinScan program or PMIScan. 3.2.3 Initialization The Eagle must be initialized before recording data. This is done by connecting the Eagle to your PC with the Eagle serial cable or through Bluetooth, and running WinScan. See the section \PC Communications with the Eagle" for information on how to connect the Eagle to the PC. See the WinScan documentation for details on how to initialize a Voltage Scanner. The Eagle may also be initialized with Palm-based PDA using the optional PMIScan software. The connection can be with the serial cable or Bluetooth. Please see the PMIScan manual for further details. 3.2.4 LED Indicator The unit has an LED that will indicate when the unit is counting down by blinking once per second. The LED will blink once every six seconds when the unit is in record mode. Lastly, the LED will stay lit when communicating with the unit. 21 Eagle Class PQ Wireless ™ Digital Recorder Manual An outline of WinScan™ Chapter 4 4.1 RETRIEVING DATA FROM THE RECORDER After your Recorder has finished collecting data, you need to download the data in order to analyze it on your computer. This process can be accomplished either over blue tooth (if your PDA or computer have a Blue tooth device) or via a serial cable. As the data is downloaded, your computer will save it in a file which can later be opened and analyzed. Please refer to the WinScan™ Manual for instructions. Figure 4-1 illustrates the basic structure of WinScan™. As you can see, the main menu option HELP leads to information on the program, while the option FILE leads to operations involving the Recorder, the data it collects, and the tools needed to interpret that data. File Main Menu Help Program Info Load Scanner Connect Computer settings Scanner settings Create, view and print graphs Create, view and print reports Data retrieval Figure4-2: Software outline The most useful options in the FILE menu are RECORDER CONTROL and LOAD. As shown in the diagram, RECORDER CONTROL leads to options which adjust settings on the Recorder and computer. These options regulate the collection and retrieval of data by the Recorder. The other important option, LOAD, is the gateway to creating, viewing and printing WinScan™ graphs and reports. Familiarize yourself with all the operations of WinScan™ as described in this manual before attempting to use your Recorder. After you are familiar with WinScan™, use the Quick Guide, in the WinScan™ Manual, as a reminder of the steps required for certain operations. For your own protection, please take the time to read Safety Issues, before installing or operating the Recorder. 22 Eagle Class PQ Wireless ™ Digital Recorder Manual Appendix 1: PC and Recorder configuration factory settings PC SETUP OPTION FACTORY SETTING Local: Serial Port Local: Baud Rate Modem: Serial Port Modem: Baud Rate Dialing Method Auto Recorder Reset Scale Factor: Voltage Scale Factor: Current Auto Clock Reset Auto Data Save Stripchart Report Header Com 1 28800 Com 2 Auto Tone Prompt On On Checked RECORDER SETUP/INITIALIZE OPTION FACTORY SETTINGS LED Indicator Interval Recording Overwrite Ab. LED Trigger Duration Interval Data Storage Significant Change Threshold Modem Ring Count Number of Channels Rotary Switch Override Recording Interval Checked Checked 5 seconds 100 percent 3 volts 3 rings Not Checked 1 minute EVENT RECORDING PARAMETERS 120 volts 6 volts 10 cycles Nominal Voltage Threshold Bands Minimum Event Time Default settings are identical for all four channels. 23 Eagle Class PQ Wireless ™ Digital Recorder Manual FLICKER PARAMETERS—from ANSI/IEEE STANDARD 141 Period Tolerance (%) 10 seconds 1.5 1 minute 15 minutes 2.5 30 minutes 1 hour 3.5 4 hours 8 hours 12 hours 24 hours Default settings are identical for all four channels. ABNORMAL LED INDICATORS Nominal Limit 10 10 10 10 10 10 10 10 Low Range Standard: 120 10 Standard: 208 12 Standard: 240 13 Standard: 277 24 Standard: 480 Custom: 106 11 Custom: 203 Default settings are identical for all four channels. High Range 12 20 24 27 48 10 23 24 Eagle Class PQ Wireless ™ Digital Recorder Manual Appendix 2: Warranty Clause Power Monitors Inc. (PMI) warrants each new product manufactured and sold to be free from defects in material, workmanship, and construction, and that when used in accordance with this manual will perform to applicable specifications for a period of one year after shipment. If examination by PMI discloses that the product has been defective, then our obligation is limited to repair or replacement, at our option, of the defective unit or its components. PMI is not responsible for products which have been subject to misuse, alteration, accident, or for repairs not performed by PMI. The foregoing warranty constitutes PMI’s sole liability, and is in lieu of any other warranty of merchantability or fitness. PMI shall not be responsible for any incidental or consequential damages arising from any breach of warranty. Equipment Return If any PMI product requires repair or is defective, call PMI at (800) 296-4120 before shipping the unit to PMI. If the problem cannot be resolved over the phone, PMI will issue a return authorization number. For prompt service, all shipments to PMI must include: 1. 2. 3. 4. 5. 6. Billing and shipping address for return of equipment. The name and telephone number of whom to contact for further information. A description of the problem or the work required. A list of the enclosed items and serial numbers. A return authorization number. If possible, a copy of the original invoice. Equipment returned to PMI must be shipped with freight charges prepaid. After repair, PMI will return equipment F.O.B. factory. If equipment is repaired under warranty obligation, freight charges (excluding air freight or premium services) will be refunded or credited to the customer’s account. Return equipment to: Power Monitors Inc. 1661 Virginia Avenue Harrisonburg, VA. 22802 USA Attention: Repair Department 25 Eagle Class PQ Wireless ™ Digital Recorder Manual Appendix 3: Troubleshooting Symptom Unit indicates negative real power, wrong phase angle Unit indicates negative real power, wrong phase angle Current clamp "buzzes" when connected around conductor. Unit will not communicate Unit will not communicate Unit will not download data Recorder downloads to 99% and gives serial comm error Strip chart shows very high or wildly fluctuating, unrealistic readings or spikes on V and I Possible Solution Voltage leads on this channel may be reversed; also may be due to reversed current CT connection Current CT may be reversed, clamped around conductor in wrong direction; also may be due to reversed voltage leads. Clamp jaws not closing completely, or dirt/rust on surface of metal jaws; Clean contacts and retry. Also try a different CT Make certain that Local and Modem port are set to different com #s, and that Palm Pilot HotSync Manager is turned off! Insure the serial port is correct and serial cables are correct. Retry at different baud rates. Turn off power management (or power saving) in the Windows control panel and the bios. Retry. Try Different baud Rates, Bring up the task manager in Windows and "end task" for all programs except WinScan™, Systray, and Explorer, Retry. Contact PMI for assistance and/or WinScan™ upgrade Contact PMI for an upgrade and retry. Contact PMI for WinScan™ Upgrade Waveform capture graph does not plot time axis correctly; 50Hz sinusoidal waveform plotted with 60Hz period. Waveform capture graph does not plot time axis correctly; 50Hz sinusoidal waveform plotted with 60Hz period. Contact PMI for WinScan™ Upgrade Some current channels do not work on flex CT's. Possible wires in flex CT are cut or nicked. Try a different set or Contact PMI for Evaluation 26 Eagle Class PQ Wireless ™ Digital Recorder Manual Appendix 4: Eagle Class Recorder™ Formulas 27 Eagle Class PQ Wireless ™ Digital Recorder Manual 28 Eagle Class PQ Wireless ™ Digital Recorder Manual 29 Eagle Class PQ Wireless ™ Digital Recorder Manual 30 Eagle Class PQ Wireless ™ Digital Recorder Manual APPENDIX 5: Regulatory Information U.S. FCC Part 15 and Industry Canada RSS 210 Statements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The letters “IC” have no other meaning or purpose than to identify the Industry Canada certification number/registration number. FCC Warning Changes or modifications not expressly approved by Power Monitors Inc. could void the user’s authority to operate this equipment. Safety Warning In order to ensure user safety and maintain a water tight, pollution free internal environment, this product, including the enclosure lid, has been sealed shut at the factory. There are no user serviceable parts inside. Any attempt to open the sealed lid could pose a safety hazard, compromise the watertight integrity of the enclosure, and may permanently alter the required electrical isolation between high voltage circuitry and the user. The AC line fuse, MOV, and the internal batteries (memory backup Lithium battery, and the NIMH ride-through battery) are replaceable, but should only be performed by PMI Inc. to ensure continued product safety and performance. 31 Eagle Class PQ Wireless ™ Digital Recorder Manual INDEX Power Monitors Inc. Address, 26 Phone number, 1 Warranty, 26 Power Requirements, 12, 15 RS232 Serial Cable, 21 SAFETY, 6, 13 Safety Issues, 6 Scanner Batteries, 15 Installing, 16 Memory, 12 Power, 15, 17 Retrieving data from, 23 Specifications, 12 SCANNER CONNECT, 23 Specifications, 15 Storage, 12, 14, 24 Two-minute countdown. See Countdown, initialization Voltage clip leads, 16 Color-coding, 16 Voltage leads, 16 WARNING, 6, 13, 15 WinScan, 9 Wye circuit, 18 : 3 wire wye, 19 : Two phase three wire, 20 2.5 Element Z-coiL, 20 3 wire wye, 19 4 Wire Delta, 18 4 wire wye, 19 AC Adapter, 10 Adapters, 11 Alligator clips. See Voltage clip leads Cases, 11 Clock, 10, 24 Countdown, initialization, 17 Current Clamps, 11 Current Probe, 11 Current probes, 7, 16 Precautions when installing, 16, 17 Default settings. See Factory settings Delta circuit, 17 ENVIRONMENTAL PRECAUTIONS, 15 Factory settings, 24 Inputs, 9 LCD, 8, 10, 17 Models, 9 modem, 16 Palm, 9 PalmScan, 9 Power adapter, 15 32
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 32 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:ffda713a-fb04-48af-a5b1-6517af36d9ab Producer : Acrobat Distiller 6.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2003:12:19 10:24:41-05:00 Create Date : 2003:12:19 10:24:41-05:00 Document ID : uuid:93ea89e2-c651-4d94-bd0e-012513971552 Format : application/pdf Title : Microsoft Word - Eagle users manual 1203.doc Creator : gks Author : gksEXIF Metadata provided by EXIF.tools