Powerwave Technologies 5JS0042 Linear Feed-Forward Power Amplifier User Manual Part 3

Powerwave Technologies Inc Linear Feed-Forward Power Amplifier Part 3

User Manual Part 3

Download: Powerwave Technologies 5JS0042 Linear Feed-Forward Power Amplifier User Manual Part 3
Mirror Download [FCC.gov]Powerwave Technologies 5JS0042 Linear Feed-Forward Power Amplifier User Manual Part 3
Document ID74210
Application IDt4GYcVoqchP/OVzrhynFnQ==
Document DescriptionUser Manual Part 3
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize13.67kB (170895 bits)
Date Submitted1999-12-07 00:00:00
Date Available2000-04-06 00:00:00
Creation Date2001-05-09 15:55:12
Producing SoftwareAcrobat Distiller 4.0 for Windows
Document Lastmod2001-05-09 15:55:13
Document TitleUser Manual Part 3

Section
GENERAL DESCRIPTION
1-1. INTRODUCTION
This manual contains information and procedures for installation, operation, and maintenance of
Powerwave’s Generation 3.1 amplifier system. The manual is organized into six sections as
follows:
Section 1. General Description
Section 2. Installation
Section 3. Operating Instructions
Section 4. Principles of Operation
Section 5. Maintenance
Section 6. Troubleshooting
1-2. GENERAL DESCRIPTION
The G3X-800 Series (NTL107AA) amplifier (figure 1-1) is a linear, feed-forward power amplifier
that operates in the 25-MHz frequency band from 869 MHz to 894 MHz. The amplifier can
simultaneously transmit multiple frequencies, with better than -65 dBc third order intermodulation
distortion (IMD). The amplifier system is modular in design, and is ideally suited for use in
AMPS/TDMA/CDMA base stations. The plug-in G3X-800 Series (NTL107AA) amplifier modules
can each provide 110 watts of power and function completely independently of each other. The
amplifier modules are designed for parallel operation to produce high peak power output and
backup redundancy for remote applications. The system is housed in the MCR20XX Series
(NTL107AC) subrack (figure 1-2) which holds two G3X-800 Series (NTL107AA) amplifiers to
produce up to 200 watts output. All solid-state, the system is designed to provide trouble-free
operation with minimum maintenance. The system's modular construction and unique and highly
effective LED-based operational status and fault indicators help minimize downtime. The turn-on
and turn-off sequences of voltages are fully automatic, as is overload protection and recycling.
Inadvertent operator damage from front panel manipulation is virtually impossible.
Notice
To comply with FCC regulations, no
channels existing within 200 kHz spacing
from the edges of any frequency block are to
be used for transmission.
The MCR20XX Series (NTL107AC) subrack contains an RF power splitter/combiner and a control
module that monitors the functional status of all plug-in amplifiers. The rear panel of the subrack
has the system RF I/O connectors and DC power input terminals. The front panel of each
amplifier module has unit level status/fault indicators and a power on/off circuit breaker. Primary
power for the amplifier system is +27 Vdc. Cooling for each plug-in amplifier module is provided
by two fans mounted on the front and two on the rear of the module. The fans draw outside air
through the front of the module and exhaust hot air out through the rear of the module.
044-05055 Rev. A
1-1
1-3. FUNCTIONAL AND PHYSICAL SPECIFICATIONS
Functional and physical specifications for the amplifier system are listed in table 1-2.
1-4. EQUIPMENT CHANGES
Powerwave Technologies, Inc. reserves the right to make minor changes to the equipment,
including but not necessarily limited to component substitution and circuitry changes. Changes
that impact this manual may subsequently be incorporated in a later revision of this manual.
1-5. ORDERING INFORMATION
Table 1-1 following gives the part numbers and descriptions to be used when ordering either an
entire system or individual major components that comprise the system.
SYSTEM
ORDER
NUMBER
MCR20XX
Series
(NTL107AC)
044-05055 Rev. A
Table 1-1. Major System Components
DESCRIPTION OF
SUBQTY
SYSTEM NUMBER
COMPONENT
PER
MODEL
SYSTEM
NUMBER
200 W 869-894 MHz Linear
System for Base Station
Equipment.
DESCRIPTION OF SUBCOMPONENT MODEL
NUMBER
MCR20XX
Series
(NTL107AC)
2-Unit 23” Subrack.
G3X-800
Series
(NTL107AA)
110 W 869-894 MHz Amplifier
Module.
800-00972-001
Front fan assembly (Intake)
800-00972-002
Rear fan assembly (Exhaust)
1-2
044-05055 Rev. A
1-3
044-05055 Rev. A
1-4
Table 1-2. Generation 3.1 Multicarrier Cellular Amplifier System Functional Specifications
Frequency Range:
Total Output Power (Minimum) in
MCR20XX (NTL107AA) System:
Maximum Input Power
Intermodulation Distortion
and In-Band Spurious:
Nominal RF Gain:
Gain Variation:
Output Port Return Loss:
Output Protection:
Input Port Return Loss:
Second Harmonic:
Out of Band Spurious:
DC Input Voltage:
DC Input Current:
PA Self Protection:
Operating Temperature:
Storage Temperature:
Operating Humidity:
Storage Humidity:
Connectors
DC Power:
RF INPUT:
RF OUT (Antenna):
SYSTEM ALARM:
RS-485
MICROPROCESSOR INTERFACE
Alarms
Monitors
Dimensions:
G3X-800 Series (NTL107AA)
Amplifier:
MCR20XX Series
(NTL107AC) Subrack:
044-05055 Rev. A
869-894 MHz
110 W typical (1 Module)
200 W typical (2 Modules)
Overdrive fault activates when input power >5 dBm
-68 dBc (Typical) @ +24 to +28 Vdc @ 200 Watts
(-65 dBc (Max) @ +21.7 to +24 Vdc)
31 ±1 dB to 49 ±1 dB Adjustable
± 0.6 dB @ 27 Vdc ±1 Vdc
+ 0.6 / -0.8 dB @ 24 to 26 Vdc
16 dB (Min)
Mismatch Protected (Isolator)
16 dB (Min)
-13 dBm (Max)
-60 dBc (Max) @ +24 to +28 Vdc
21.7 to 30 Vdc (24 to 28 Vdc for rated operation)
110 Amps (Typical) @ 27 ±1 Vdc Input, 200 Watts
MCA Disabled Upon 5-Second Continuous Alarm
-5 ºC to +60 ºC Ambient
-40 ºC to +85 ºC
5% - 95% Relative Humidity (Noncondensing)
0% - 95 % Relative Humidity (Noncondensing)
¼-20 studs
SMA
Type N
9-Pin D-Subminiature Female
9-Pin D-Subminiature Female
9-Pin D-Subminiature Female
Over Power, VSWR, DC Failure, High Temperature, Loop
Failure, Fan Failure
Forward Power and Reverse Power
5.22" High, 17.00” Wide, 20.44” Deep
(Including handles, rear fans)
11.33” High, 23.00” Wide, 22.77” Deep
(With amplifiers inserted)
1-5

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:05:09 15:55:12
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:05:09 15:55:13-04:00
Page Count                      : 5
EXIF Metadata provided by EXIF.tools
FCC ID Filing: E675JS0042

Navigation menu