Powerwave Technologies 5JS0056 Multi Carrier RF Power Amplifier User Manual 273676
Powerwave Technologies Inc Multi Carrier RF Power Amplifier 273676
Contents
Manual 1
G3S-800-140-031 Installation & Service Manual Section 1 General Description 1-1 Introduction This manual contains information and procedures for installation, operation, and maintenance of Powerwave’s G3S-800-140-031 multicarrier RF power amplifier. The manual is organized into six sections as follows: Section 1. General Description Section 2. Installation Section 3. Operating Instructions Section 4. Principles of Operation Section 5. Maintenance Section 6. Troubleshooting 1-2 General Description The G3S-800-140-031 (see figure 1-1) is a linear, feed-forward power amplifier that operates in the frequency band from 851 MHz to 869 MHz. The amplifier can simultaneously transmit multiple frequencies, with better than -60 dBc third order intermodulation distortion (IMD). It is designed for use in an amplifier system that is modular in design, and is ideally suited for use in base stations. The plug-in Model G3S-800-140-031 amplifier modules can each provide 140 watts of power and function completely independently of each other. The amplifier modules are designed for parallel operation to produce high peak power output and backup redundancy for remote applications. All solid-state, the system is designed to provide trouble-free operation with minimum maintenance. The system's modular construction and unique and highly effective LED-based operational status and fault indicators help minimize downtime. The turn-on and turnoff sequences of voltages are fully automatic, as is overload protection and recycling. Inadvertent operator damage from front panel manipulation is virtually impossible. The amplifier module has a status connector that allows the host system to monitor the amplifier module performance. The front panel of each amplifier module has unit level status/fault indicators and an RF on/off/reset switch. Primary power for the amplifier is +27 Vdc. Cooling for each plug-in amplifier module is provided by four fans, two mounted on the front and two on the rear of the module. The fans draw outside air through the front of the module and exhaust hot air out through the rear of the module. 1-3 Functional And Physical Specifications Functional and physical specifications for the amplifier are listed in table 1-2. 1-4 Equipment Changes Powerwave Technologies, Inc. reserves the right to make minor changes to the equipment, including but not necessarily limited to component substitution and circuitry changes. Changes that impact this manual may subsequently be incorporated in a later revision of this manual. Copyright Powerwave Technologies, Inc., September 2001. All rights reserved All specifications are subject to change without notice. Contact the factory for complete performance data. 1-1 September 2001 044-05095 Rev. A G3S-800-140-031 Installation & Service Manual 1-5 Ordering Information Table 1-1 following gives the part numbers and descriptions to be used when ordering either an entire amplifier or replacement fans. Table 1-1 Major Amplifier Components Model Number G3S-800-140-031 800-01075-003 800-00972-002 Description 140 W 851-869 MHz MCPA Module Front fan assembly Rear fan assembly. Table 1-2 G3S-800-140 Multicarrier Cellular Amplifier Functional Specifications Frequency Range Instantaneous Bandwidth Total Maximum Input Power Total Output Power IMD and In-band Spurious, mean measurement, 30 kHz bandwidth@ +26 to +28Vdc, 25°C Out of Band Spurious & Noise, measured in 30 KHz BW RF Gain Gain Flatness: Gain Variation w/ Voltage and Frequency Gain Variation Over Temperature: Noise Figure Output Protection: Input Port Return Loss: Harmonics: Out of Band Spurious: Duty Cycle: DC Input Power: DC Circuit Breaker Rating Operating Temperature: Storage Temperature: Operating Humidity: Storage Humidity: DC Input, Summary Alarm, and RF Input / Output Connectors: Heat Generation Weight Dimensions: Electrical Service Recommendations Circuit Breakers 851-869 MHz (18 MHz Bandwidth) 18 MHz -6.54 dBm 140 W (51.46 dBm) typical (1 Module) -60dBc or -16 dBm max @ up to 16 equal power CW tones with a combined maximum power of P0 with a max single carrier power of P0/16 with maximum crest factor of 7.5dB up to the maximum rated RF output power. -60 dBc max @ +26 to +28 Vdc 58 dB +0.5 dB ±0.5 dB @ 27 Vdc ±1 Vdc + 0.5 dB; 26 to 28 Vdc ±0.5 dB 25 dB max Mismatch Protected 16 dB min Better than -50 dBc Better than -60 dBc Continuous +27 Vdc ±1 Vdc, 70 amps max Operational +21 Vdc to 30 Vdc 100 Amps 0º C to +50º C -40º C to +85º C 0 % to 80 % Relative Humidity (noncondensing) 0 % to 100 % Relative Humidity (noncondensing) 21-Pin D-Subminiature Combo Connector plus singlepin D-Sub connector for additional DC capability. 5510 BTUS (1 Amplifier) 50 lbs. 5.20” High, 17.00” Wide, 20.00” Deep Capable of handling anticipated inrush current (normally 25% over equipment maximum current draw), in a load center with a master switch. Copyright Powerwave Technologies, Inc., September 2001. All rights reserved All specifications are subject to change without notice. Contact the factory for complete performance data. 1-2 September 2001 044-05095 Rev. A G3S-800-140-031 Installation & Service Manual Figure 1-1 G3S-800-140-031 Copyright Powerwave Technologies, Inc., September 2001. All rights reserved All specifications are subject to change without notice. Contact the factory for complete performance data. 1-3 September 2001 044-05095 Rev. A
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2002:09:30 12:26:09-07:00 Modify Date : 2002:09:30 12:26:09-07:00 Page Count : 3 Creation Date : 2002:09:30 19:26:09Z Mod Date : 2002:09:30 19:26:09Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : Administrator Metadata Date : 2002:09:30 19:26:09Z Creator : Administrator Title : Microsoft Word - 273676.DOCEXIF Metadata provided by EXIF.tools