Powerwave Technologies 5JS0095 Multi-Carrier Power Amplifier User Manual 044 3505 Rev A G3L 1929 160 001

Download:
Mirror Download [FCC.gov]
Document ID	873856
Application ID	RZLctSuIacDixOw/svkyoA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	79.34kB (991693 bits)
Date Submitted	2007-11-29 00:00:00
Date Available	2007-12-05 00:00:00
Creation Date	2007-09-06 07:43:11
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2007-09-06 07:46:42
Document Title	044-3505 Rev A G3L-1929-160-001.book
Document Creator	PScript5.dll Version 5.2.2
Document Author:	rwillett

G3L-1929-160-001
Multi-Carrier
Power Amplifier
Installation and
Service Manual
044-05305 Rev A
August 2007
© 2007 Powerwave Technologies Incorporated. All rights reserved.
Powerwave Technologies, and the Powerwave logo are registered trademarks.
This Powerwave product is intended only for installation in a RESTRICTED ACCESS LOCATION and
this Powerwave product is designed to operate within the normal operating (typical operating) ranges
or conditions specified in this document. Operation of this equipment beyond the specified ranges in
this document may cause:
1. Spurious emissions that violate regulatory requirements.
2. The equipment to be automatically removed from service when maximum thresholds are exceeded.
3. The equipment to not perform in accordance with its specifications.
It is the operator’s responsibility of the operator to ensure this equipment is properly installed and
operated within Powerwave operating specifications to obtain proper performance from the equipment
and to comply with regulatory requirements.
For PERMANENTLY CONNECTED EQUIPMENT, a readily accessible disconnect device shall be
incorporated in the building permanent wiring.
Warnings, Cautions, and Notes
Warnings, Cautions, and Notes are found throughout this manual where applicable. The associated
icons are used to quickly identify a potential condition that could result in the consequences described
below if precautions are not taken. Notes clarify and provide additional information to assist the user.
WARNING: This warning symbol means danger. You are in a situation that could cause
bodily injury or death. Before working on any equipment, be aware of the hazards involved
with electrical and RF circuits and be familiar with standard practices for preventing accidents.
CAUTION: The caution symbol means reader be careful. In this situation, the user might do
something that could result in equipment damage or loss of data.
NOTE The note symbol means reader take note. Notes contain helpful suggestions or references
to material not covered in this document. Procedures are not contained in notes.
044-05305 Rev A
Revision Record
Revision Letter
ii
Date of Change
Reason for Change
Aug 2007
Initial Release
044-05305 Rev A
Table of Contents
Chapter 1 - Product Description
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Chapter 2 - Controls and Indicators
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
MCPA Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Chapter 3 - Installation
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Damaged Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Air Conditioning Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
MCPA Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Initial Start-up and Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Chapter 4 - Maintenance
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
MCPA Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Return for Service Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Obtaining an RMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Repackaging for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Chapter 5 - Specifications
Multi-Carrier Power Amplifier Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
044-05305 Rev A
iii
Table of Contents
G3L-1929-160-001
List of Figures
1-1 MCPA Front and Rear Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-2 MCPA Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2-1 MCPA Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2-2 MCPA Interface Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
3-1 MCPA Quarter-Turn Fasteners and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
List of Tables
2-1 MCPA Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2-2 MCPA Alarm States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2-3 MCPA Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
3-1 MCPA Unpacking and Inspection Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3-2 MCPA Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3-3 Initial Start-up Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
4-1 Recommended Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4-2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4-3 MCPA Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
5-1 MCPA Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
iv
044-05305 Rev A
Chapter 1
Product Description
Introduction
This manual contains information and procedures for the installation, operation, and maintenance of the
G3L-1929-160-001 Multi-Carrier Power Amplifier (MCPA).
Scope of Manual
This manual is intended for use by service technicians familiar with similar types of equipment. It contains
service information required for the equipment described and is current as of the printing date. Changes which
occur after the printing date may be incorporated by a complete manual revision or alternatively as additions.
The manual is organized into the following chapters:
❑
❑
❑
❑
❑
Chapter 1 - Product Description
Chapter 2 - Controls and Indicators
Chapter 3 - Installation
Chapter 4 - Maintenance
Chapter 5 - Specifications
Product Description
The MCPA shown in Figure 1-1 MCPA Front and Rear Views is a linear, feed-forward multi-carrier power
amplifier that operates in the PCS band from 1930 MHz to 1995 MHz with an instantaneous bandwidth of
65 MHz. The instantaneous bandwidth is the maximum frequency band in which any two or more signals can
occupy. The instantaneous bandwidth of the MCPA is set automatically.
The MCPA is modular in design and ideally suited for use in CDMA 2000, CDMA and and 1X-EVDO base
stations. The MCPA provides a gain of 63 dB to supply a 160 watt output. Refer to Figure 1-2 MCPA
Functional Block Diagram for the MCPA functional block diagram. Refer to Chapter 5 for the MCPA
specifications.
Functional Description
The MCPA is a self-contained module typically operated in parallel with other identical MCPAs as part of a
subrack assembly.
The MCPA consists of the following major functions:
❑
Preamplifier
❑
Main and error amplifiers
❑
Feed-forward loop control
❑
Pilot tone generator
❑
Controller
❑
Cooling
❑
Power Distribution
044-05305 Rev A
1-1
Functional Description
G3L-1929-160-001 MCPA
Rear
Front
Figure 1-1 MCPA Front and Rear Views
1-2
044-05305 Rev A
G3L-1929-160-001 MCPA
Functional Description
FIRST LOOP
SECOND LOOP
Pilot Tone
First Loop
Phase and Gain
Premain
Amplifier
Delay
Filter
Main
Amplifier
RF Out
RF Sample
Pilot Tone
Generator
RF In
Preamp
First Loop
Detection
First Loop
Control
Error Out
Second Loop
Phase and Gain
Delay
Second Loop
Control
Forward Power / Pilot Tone Detect
Reflected Power (VSWR)
Controller
-5
+15 +9 +5
VDC VDC VDC VDC
+27 VDC
Error
Amplifier
System
Faults
Front Panel
Status
User
Interface
LED
Control ON/OFF/RESET
Switch
Figure 1-2 MCPA Functional Block Diagram
Preamplifier
The carrier (RF In) is applied to the input port of the MCPA and fed to the preamplifier stage where it is
amplified using two stages of class A mode amplifiers. The output of the preamplifier is split into two paths, one
to the main amplifier and one to the error amplifier.
Main and Error Amplifiers
The main amplifier provides the balance of gain and power in the 1930 MHz to 1995 MHz frequency band,
using class AB amplification for maximum efficiency. The error amplifier and feed forward loops correct signal
non-linearities introduced by the class AB main amplifier.
In the error amplifier, which operates in class A mode, the RF signal is coupled to an attenuator and phase
shifter in the first feed-forward loop, phase shifted by 180 degrees and then amplified in the premain amplifier.
The output from the pre-main amplifier is fed to the class AB main amplifier and then sampled using a coupler.
The signal (RF sample) is combined with the main input signal and input to the second feed-forward loop.
There, the RF sample is attenuated, phase shifted 180 degrees, and fed to the error amplifier where it is
amplified to a level identical to the sample output from the main amplifier. The output from the error amplifier
(Error Out) is coupled back and added to the output from the main amplifier, with the control loops continuously
making adjustments to cancel out any distortion in the final output signals.
044-05305 Rev A
1-3
Functional Description
G3L-1929-160-001 MCPA
Feed-forward Loop Control
The primary function of the first loop is to amplify the carrier signals and isolate an error signal for the second
loop. It does this by amplifying the carrier signals and isolating an error signal which is passed to the second
loop. The first loop control section phase shifts the main input signals by 180 degrees and constantly monitors
the output for correct phase and gain.
The primary function of the second loop is to amplify the error signal to cancel out spurious products developed
in the main amplifier. The input signal is amplified by a preamplifier and fed to a coupler and delay line. The
signal from the coupler is fed to the attenuator and phase shifter in the first loop.
The second loop control section obtains a sample of the distortion added to the output signals by the main
amplifiers. The signal is phase shifted 180 degrees, then fed to the error amplifier where it is amplified to the
same power level as the input sample. The signal is then coupled to the main amplifier output. The final output
is monitored by the second loop and adjusted to ensure that the signal distortion and intermodulation distortion
on the final output is cancelled out.
During routine operation, all normal variations are automatically compensated for by the feed-forward loop
control. If large variations occur beyond the adjustment range of the loop control, the controller shuts down the
MCPA RF section and a loop fault is reported to the system.
Pilot Tone Generator
The pilot tone is an internally generated signal with a predetermined frequency, phase, and amplitude is
known. If the pilot signal is suppressed at the amplifier output, then the distortion created by the main amplifier
is also suppressed.
The pilot tone signal is injected into the first loop and detected at the feedforward output of the second loop.
The pilot tone is coupled off of the main amplifier creating a second pilot tone that is attenuated and phase
shifted 180 degrees to be used as the reference. The second pilot tone is amplified in the error amplifier and
mixed with the signals from the main signal path.
The first and second pilot tones should cancel each other out in an ideal situation. If the output detector senses
that the pilot tones do not cancel each other out, the information feeds back to control the gain and phase of
both the main and error amplifier paths minimizing output distortion.
Controller
The controller constantly compares the active RF paths with internal references for dynamic correction of small
variations through the RF feedback control circuits to maintain constant gain, and also provides the alarm
monitoring and control for the MCPA.
A front panel mounted tri-color LED provides MCPA operational status to the local operator. The OFF/ON/
RESET switch allows the operator to power on, power off or reset the MCPA. System faults are sent to a
remote location through the user interface.
Cooling
The MCPA components are mounted on a heatsink and cooled by forced air flowing over the heatsink fins.
System fans draw external air through the MCPA front panel inlet and exhaust air through the MCPA rear
panel outlet. The internal temperature is monitored to keep the MCPA within the specified operating
temperature.
1-4
044-05305 Rev A
G3L-1929-160-001 MCPA
Functional Description
Power Distribution
The host system provides +26 to 28 VDC power for the MCPA. The DC/DC converter and voltage regulator in
the MCPA converts the +27 VDC to +15 VDC, +9 VDC, +5 VDC, and -5 VDC for internal use. The MCPA has
no built-in short-circuit protection.
The MCPA operates at full power if the system DC supply is within 26 to 30 VDC. The MCPA shuts down if the
applied DC power is less than 20.5 VDC or greater than 30.5 VDC.
044-05305 Rev A
1-5
Functional Description
G3L-1929-160-001 MCPA
This page intentionally left blank.
1-6
044-05305 Rev A
Chapter 2
Controls and Indicators
Introduction
This chapter contains descriptions of the G3L-1929-160-001 Multi-Carrier Power Amplifier (MCPA)
controls and indicators.
MCPA Controls and Indicators
The location of the MCPA controls and indicators are illustrated in Figure 2-1 and listed with
descriptions in Table 2-1.
Multi-color LED
Status Indicator
OFF/ON/RESET Switch
Figure 2-1 MCPA Controls and Indicators
MCPA Alarms
MCPA alarm conditions are reported to the system as logic level signals through the rear connector.
The front panel LED provides a visual reference for the operator of MCPA status. Refer to Table 2-1
for a listing of LED states. Refer to Table 2-2 for a listing of Alarm states.
044-05305 Rev A
2-1
MCPA Controls and Indicators
G3L-1929-160-001 MCPA
Table 2-1. MCPA Controls and Indicators
Controls and Indicators
Description
Toggle Switch, Three Position
RESET (Up)
Resets MCPA. LED indicates boot mode (red), then turns solid
green
ON (Center)
Enables MCPA. LED indicates solid green
OFF (Down)
Disables MCPA. LED Indicates solid red
LED, Status
Green (solid)
RF enabled, OFF/ON/RESET switch set to On (center position),
normal operation, no alarm
Green (blinking)
Standby
Yellow (solid)
Minor Alarm - APC function enabled
Yellow (blinking)
VSWR Warning
Red (solid)
Major alarm - Critical fault present.
Red/Yellow (alternating)
Downloading. Do not interrupt power.
Table 2-2 MCPA Alarm States
Alarm
Definition
Alarm type/LED
Auto-Recovery
Output
Overpower
Disables MCPA immediately if
output power is >+2 dB over rated
output RF power.
Major
(Red)
Input power decreases below -4dBm
Automatic
Power Control
(APC)
Enabled if output power is > 52.67
dBm.*
Minor
(Yellow)
MCPA auto-recovers when output
power drops below rated maximum
output power.
Input
Overdrive
Disables MCPA immediately if input
RF drive is >-1 dBm
Major
(Red)
Input power decreases below -4dBm
High
Temperature
Disables MCPA if sensor
temperature is > +95° C.
Major
(Red)
MCPA auto-recovers when sensor
temperature drops to less than +85
°C.
High Reverse
Power
Disables MCPA if the reverse RF
output power is higher than 49 dBm
for a duration of 1-minute.
Minor (Yellow)
during 1minute
validation
period then
changes to
Major (Red)
Reverse power must be < 48.3 dBm.
2-2
044-05305 Rev A
G3L-1929-160-001 MCPA
MCPA Controls and Indicators
Table 2-2 MCPA Alarm States (Continued)
Alarm
Definition
Alarm type/LED
Auto-Recovery
Exceed
Maximum
Voltage
Disables MCPA immediately if
supply DC voltage > +30.5 VDC.
Major
(Red)
Auto-recovery when supply voltage
drops to < +29.5 VDC.
Below
Minimum
Voltage
Disables MCPA immediately if
supply DC Voltage < +20.5 VDC
Major
(Red)
Auto-recovery when supply voltage
increases to >+24.0 VDC
Loop Fail
(Linearization
Alarm)
Disables MCPA if loop convergence
fails.
Major
(Red)
Auto-recovery when loop converges.
MCPA tries to auto recover ten times
before permanent shut down. Two
minutes and 5 seconds for each try.
Internal DC
Fail
Alarm if internal voltages fail or out
of range.
Minor
(None)
Auto-recovery once voltage is within
range. No shutdown until linearization
alarm occurs.
Device Fail
Alarm if one or more output power
devices fail.
Minor
(None)
No auto-recovery. No shutdown until
linearization alarm occurs.
*Note: If MCPA cannot compensate gain to maintain compliance, Output Overpower or Input Overdrive faults provide
MCPA protection.
MCPA Connectors
The MCPA power, alarm, control, and RF connections are made through a D-sub combination male
interface connector located on the rear of the MCPA. Pin assignments are illustrated in Figure 2-2
and listed in Table 2-3. Alarms are interpreted and generated by the MCPA and reported to the base
station as a system level alarm. The PC I/O RJ-11 connector is for factory use only.
1 2 3 4 5 6 7 8 9
A1
A2
A3
A4
10 11 12 13 14 15 16 17
Figure 2-2 MCPA Interface Connector
044-05305 Rev A
2-3
MCPA Controls and Indicators
G3L-1929-160-001 MCPA
Table 2-3 MCPA Connector Pinouts
Pin
2-4
Function
Pin
Function
A1
RF Input (Coaxial Contact)
Summary_Fault
A2
+27 VDC (Power Contact)
DC (On/Off)
A3
Ground (Power Contact)
10
NC
A4
RF Output (Coaxial Contact)
11
NC
TX_H (RS-485)
12
NC
TX_L (RS-485)
13
NC
GND
14
NC
RX_H (RS-485)
15
NC
RX_L (RS-485)
16
HPE (High Power Enable)
GND
17
NC
MOD_DET (Module Detection)
044-05305 Rev A
Chapter 3
Installation
Introduction
This chapter contains unpacking, inspection, startup and installation procedures for the
G3L-1929-160-001 Multi-Carrier Power Amplifier (MCPA).
•
Review this chapter prior to equipment installation.
•
Review any government and local codes applicable to this installation.
•
Read the instructions in this Chapter and Chapter 4 before operating the equipment.
Unpacking and Inspection
Perform the steps in Table 3-1 to unpack and inspect the MCPA.
Table 3-1. MCPA Unpacking and Inspection Instructions
Step
Action
Carefully open container and remove MCPA.
Visually inspect MCPA for damage that may have occurred during shipment.
Check for evidence of water damage, bent or warped chassis, loose screws or
nuts, or extraneous packing material in connectors. If possible, inspect equipment
in the presence of the delivery person.
If possible, retain all packing material that can be reused for repackaging
components.
Damaged Equipment
If the MCPA is damaged, a claim should be filed with the carrier when the extent of any damage is
assessed. Contact the factory for a return material authorization (RMA). Refer to Chapter 4 for the
return procedure.
Air Conditioning Requirement
The MCPA generates 2771 BTUs of heat at 36 amps, 27 VDC and 160 watts average RF power
output. The MCPA operates within the extended low temperature and high temperature environments
as listed in Chapter 5.
MCPA Installation Instructions
CAUTION: Do not slam the MCPA into the system subrack during installation. Using
excessive force can damage the MCPA interface connector.
044-05305 Rev A
3-1
MCPA Installation Instructions
G3L-1929-160-001 MCPA
The modular MCPA can be installed in a variety of systems. All system connections to the MCPA are
made through the MCPA rear connector, no additional wiring is required. Perform the steps in Table
3-2 to install the MCPA. Refer to Figure 3-1 for quarter-turn fastener position and switch location.
Table 3-2 MCPA Installation
Step
Action
Set MCPA OFF/ON/RESET switch to the OFF (down) position.
Ensure quarter-turn fasteners are in unlocked position.
Lift and insert MCPA into the subrack. Turn the quarter-turn fasteners to locked
position to secure MCPA into subrack.
Quarter-turn
fastener
RF Switch:
RESET
ON
OFF
RJ-11
Connector
(Factory use only)
Quarter-turn
fastener
Unlocked
Locked
Interface
Connector
Figure 3-1 MCPA Quarter-Turn Fasteners and Connectors
3-2
044-05305 Rev A
G3L-1929-160-001 MCPA
Initial Start-up and Operating Procedures
Initial Start-up and Operating Procedures
Perform the MCPA initial start-up per the instructions in Table 3-3.
CAUTION: Before applying power, ensure input and output cables are properly terminated at
the Duplexer front panel. Do not operate MCPA without a load attached. Excessive input
power may damage the MCPA. Refer to Chapter 5 for input power requirements.
Table 3-3 Initial Start-up Procedure
Step
Action
Verify all system input and output cables are properly connected.
Verify +27 VDC (+/- 1 VDC) supply is available.
Set MCPA OFF/ON/RESET switch to ON (center) position.
Allow MCPA to warm-up for a minimum of two minutes before taking power readings.
044-05305 Rev A
3-3
Initial Start-up and Operating Procedures
G3L-1929-160-001 MCPA
This page intentionally left blank.
3-4
044-05305 Rev A
Chapter 4
Maintenance
Introduction
This chapter contains instructions for periodic maintenance, testing and troubleshooting for the
G3L-1929-160-001 Multi-Carrier Power Amplifier (MCPA).
Periodic Maintenance
NOTE Check your sales order and equipment warranty before attempting to service or repair unit.
Do not break seals on equipment under warranty or warranty will be null and void. Do not
return equipment for warranty or repair service until proper shipping instructions are
received from factory. See Obtaining an RMA.
Periodic maintenance requirements for the MCPA are listed in Table 4-1.
Table 4-1. Recommended Periodic Maintenance
Action
Task
Interval
Cleaning
3 Months
Inspect for debris especially around front panel vents. Remove
dust with a soft cloth/brush or vacuum cleaner
Troubleshooting
Perform the instructions in Table 4-2 in the case of an MCPA fault or alarm.
Table 4-2 Troubleshooting
Step
Action
Check for proper DC supply voltage.
Set the OFF/ON/RESET switch momentarily to RESET (Up) position.
Contact your field representative or the factory if fault does not clear.
044-05305 Rev A
4-1
MCPA Removal and Replacement
G3L-1929-160-001 MCPA
MCPA Removal and Replacement
Perform the instructions in Table 4-3 to remove and replace a MCPA.
CAUTION: Do not slam the MCPA into the system during installation. Using excessive force
can damage the MCPA connector.
CAUTION: When removing the MCPA from the system, support the MCPA to prevent the rear
of the MCPA from suddenly dropping when the guide rail disengages from the track.
Dropping the MCPA can damage the rear multi-pin connector. The MCPA weighs
approximately 28.60 lbs. (12.97 kg).
Table 4-3 MCPA Removal and Replacement
Step
Action
Set MCPA OFF/ON/RESET switch to OFF (down).
Loosen two quarter-turn fasteners that secure MCPA to the subrack.
With steady even pressure, use handle on front of the MCPA to pull the MCPA out of the
system.
To replace MCPA, set MCPA OFF/ON/RESET switch to OFF (down).
Turn quarter-turn fasteners to unlocked position.
Insert MCPA into subrack. Turn quarter-turn fasteners to locked position to secure MCPA.
Return for Service Procedures
When returning products to Powerwave, the following procedures will ensure optimum response.
Obtaining an RMA
A Return Material Authorization (RMA) number must be obtained prior to returning equipment and to
reduce delays in receiving repair service. Please contact our Repair Department at (714) 466-1000 to
obtain this number, or FAX your request to (714) 466-5816.
Repackaging for Shipment
To ensure safe shipment of a component, it is recommended that the original packing materials be
reused If this is not possible, use suitable shipping cartons and foam inserts to prevent damage in
transit.
4-2
044-05305 Rev A
Chapter 5
Specifications
Multi-Carrier Power Amplifier Specifications
The performance and physical specifications for the G3L-1929-160-001 MCPA are listed in Table 5-1.
Table 5-1. MCPA Specifications
Electrical
Specifications/Features
Operating Frequency Band
1930-1995 MHz
Instantaneous Bandwidth
65 MHz
Air Interface
CDMA, CDMA-2000, 1X-EVDO
RF Output Power
160 W Max. Nominal
150 W Max. Over all conditions
180 W APC (Automatic Power Control)
Maximum Input (before shutdown)
-1 dBm
Duty Cycle
Continuous
BTUs
2771 at 36 Amps, 27 V and 160 W average RF power output
RF Gain
63 dB
Gain Flatness
±0.5 dB (Max.)
Gain Variation over Temperature
±0.5 dB (Max.)
Spurious Emissions (ACP)
-13 dBm (Max.) 1 MHz Bandwidth
Harmonics
-13 dBm (Max.) 1 MHz Bandwidth; -50 dBc (Max.)
Out of Band Spurious
-60 dBc (Max) ITU-R, SM329-9, Category B
Input Return Loss
16 dB (Min.)
Output Return Loss
16 dB (Min.)
Input Voltage Range
+26 VDC to 28 VDC nominal; Operational range of 21.0 VDC to 30
VDC.
MCPA disables at less than 20.5 VDC or greater than+30.5 VDC.
DC Current:
(Max @ APC)
(Nominal)
36 Amps at 26 V and 160 W average RF power output.
34.8 Amps at 27 V and 160 W average RF power output.
Efficiency
>17%
Mechanical
Specifications/Features
044-05305 Rev A
5-1
Multi-Carrier Power Amplifier Specifications
G3L-1929-160-001 MCPA
Table 5-1. MCPA Specifications (Continued)
Controls
Three position toggle switch: OFF/ON/RESET.
Alarm Indication
LED; Green (normal), Yellow (minor alarm), Red (Major alarm).
Platform Compatibility
G3L-1929-160-001 will reduce power level to G3L-1929-120 levels if
placed in a G3L-1929-120 subrack. PA will perform at rated power
levels with Software upgrade for subrack.
RF Input / Output / Status / Alarm /
Control / DC Input Connector
21-pin D-subminiature combo connector.
DImensions
354.6 mm high, 99 mm wide, 499.9 mm deep (including handles)
(13.96” H X 3.9” W X 19.7” D)
Weight
12.97 kg (28.5 lbs)
Environmental
Specifications/Features
Operating Temperature Range
-33 ºC. to +50 ºC.
Storage Temperature
-40 ºC. to +70 ºC.
Operating Humidity, Normal
5% to 95% relative humidity (non-condensing).
Storage Humidity
5% to 95% relative humidity (non-condensing).
RF Power Derating for DC Input Voltage.
28.1 to 30.0 VDC - 0.5 dB
26.0 to 28.0 VDC - rated operation
25.0 to 25.9 VDC - 1.0 dB
24.0 to 24.9 VDC - 1.5 dB
21.0 to 23.9 VDC - 2.0 dB
5-2
044-05305 Rev A
Powerwave Installation and Service Manual
Worldwide Corporate Headquarters
1801 East St. Andrew Place
Santa Ana, CA 92705 USA
Tel: 714-466-1000
Fax: 714-466-5800
www.powerwave.com
Main European Office
Knarramasgatan 7 8tr
164 40 Kista, Sweden
Sweden
Tel: +46 8 540 822 00
Fax: +46 8 540 824 91
Main Asia-Pacific Office
23 F Tai Yau Building
181 Johnston Road
Wanchai, Hong Kong
Tel: +852 2512 6123
Fax: +852 2575 4860
©Copyright 2007, Powerwave Technologies, Inc. All Rights reserved. Powerwave, Powerwave Technologies, The Power in Wireless and the Powerwave logo are registered trademarks of Powerwave Technologies, Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 25
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:da8ab759-4fe9-4499-9592-fda9a0a5f31a
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2007:09:06 07:43:11-05:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2007:09:06 07:46:42-05:00
Metadata Date                   : 2007:09:06 07:46:42-05:00
Document ID                     : uuid:c9fc8319-430a-46a9-8c9a-6f2c8a974e85
Format                          : application/pdf
Title                           : 044-3505 Rev A G3L-1929-160-001.book
Creator                         : rwillett
Author                          : rwillett

EXIF Metadata provided by EXIF.tools